Hi guys, here's my problem:
When I connect my HTC to the computer only battery charges. At no time did I get the option to "Sync, Mass Storage, etc. ..".
I've tried different MicroUSB, but I think the problem is the phone.
When connected, do not install the drivers or anything, it automatically starts to charge the phone.
I had thought of sending it to HTC SAT, but the problem is that I am Root, S-OFF and bootloader unlocked with HTCDev. Would try to make the method for re-S-On, the original recovery, etc. .. I can not do any of the steps since for all you need to connect your phone to PC with USB.
I have been told to try to install an RUU, maybe that solves the problem of malfunctioning USB, but you know any other method by which it can again be S-On?
Check in your phone settings that you haven't set it to charge only rather than asking you when you plug in the cable.
And when you pull down the notification panel on the homescreen, isn't there an option showing to let you select which mode you're in?
MMoodyB said:
Check in your phone settings that you haven't set it to charge only rather than asking you when you plug in the cable.
And when you pull down the notification panel on the homescreen, isn't there an option showing to let you select which mode you're in?
Click to expand...
Click to collapse
I have everything related to the software reviewed, and never gives me the connection type.
What I'm trying to get is back to being s-on the original recovery, etc ...but it is impossible, the pc did not detected and I can not do any command from MS-DOS.
Also thanks for the reply.
By any chance have you tried a new USB cable ? The reason I'm asking is I had the same problem and it would charge only and not give me the opportunity to do anything else. Once I switched USB cables to another universal cable I was able to sync and Suddenly was recognised again. I had to use the universal cable though as my other two cables did the same thing no joy. But once I hooked up to the universal my problem was solved. So before you go as far as returning the device DO try another universal cable. You can get them from amazon for about 1.99 very inexpensively! As a matter of fact I just ordered another because cables in my case have gone bad fast . Perhaps because I buy the cheap ones. Lol. But do try it. It solved my problem right away. It won't hurt to try. Strange thing was it didn't work on my other two cables only my universal cable. But I'm ok with that because it IS working perfectly now using the universal cable. Like I said its worth a try . Hope this helps you out. Best wishes!
Sent from my Sensation Z710e using xda premium
Related
I've looked everywhere and cant seem to find an answer, so i figured i'd start a new thread.
My captivate used to connect to my computer just fine, but there was another computer it would just NOT connect too! Well, after a few months, it stopped connecting to my home computer as well.
I have USB debugging on, the phone is rooted and everything. When I plug it in and mount the USB drives, i get drives J and K on my computer, one for the internal storage, and one for the SD card i have in the phone.
When double clicking any of those drives, it just sits there and reads forever without ever doing anything. I can use the SDK to run "adb devices" and it see's the phone, Odin One Click finds the phone but freezes on reading file line, or just fails all together.
Any ideas?
Try reinstalling the samsung usb drivers and restart your computer, that'd be my first step.
Sent from my SAMSUNG-SGH-I897 using XDA App
You have to be on the touch wiz home screen if you're trying to connect to Kies, otherwise turn on USB debugging and you should be good to go
Sent from my SAMSUNG-SGH-I897 using XDA App
SeenNotScene: I've uninstalled, rebooted, re-installed several times. I've been having this problem for a couple months now and i've tried everything i can think of. It doesnt work
bkhams: I dont even know what Kies is? I always have USB debugging turned on, and once connected i bring down the drop down menu and mount the USB so i can access my phones files as if they were another drive.
I had the same problem, and Samsung peeps told me I had to use the USB cable that came with the phone, low and behold they were right. Connected right away with the USB that came with the phone, could that be your problem?
I had the same problem in the past and it was actually a hardware problem with the Captivate and not anything with the computer. I ended up taking the phone in and they exchanged it for me.
I do not know if yours could be having the same problem, but that was my experience. Frustrating, to say the least.
Hmm... Could be the hardware i guess.. I know its not the cable though because i've only ever used the cable that came with it.
Have you tried connecting to the USB port directly off the motherboard? My connections were "sketchy" at best when using the ports of the top of the computer case. Once I connected directly off the MOBO, zero problems since.
Sloved!
axis01 said:
Have you tried connecting to the USB port directly off the motherboard? My connections were "sketchy" at best when using the ports of the top of the computer case. Once I connected directly off the MOBO, zero problems since.
Click to expand...
Click to collapse
Thank you for suggestions! My front USB connector is probably connected to some internal HUB, not going straight to the motherboard and wont work. Connecting directly to MB USB solve the problem. I am a little bit surprised... but whatever - M$ bull*hits. I spend couple of hours yesterday to find out whats going on. Thank you again!
I have been searching for about a week now and still can't figure this problem out. I bought this phone used about a month ago and I haven't tried to connect it to my pc until just recently. I am wanting to root and unlock my phone but I can't connect to pc using usb cord although it will charge it.
I am on GB 2.3.6 vuvkj6, stock.
I have tried 4 different usb cords, 4 different pc/laptops and all usb ports. I have also installed and uninstalled several usb drivers with no luck.
My phone can only get into download mode using a jig. Even in download mode, I can't connect to pc. I have tried using Heimdall, Odin, and kies but it just does not connect.
If I can use a jig to get it into dl mode, does that mean the phones usb port is fine?
I just want to be able to connect with pc. Is it possible to flash using my sdcard? I am thinking maybe the phone is missing something to pick up the usb signal or something.
I am lost, any help would be appreciated.
Maybe, I think it's a phone issue.
Do you still have a warranty?
I bought this phone used, so no warranty. If the jig works, does that mean the usb port is ok?
Does the phone charge when plugged in? Have you tried to go ahead and flash even though it says not recognized?
ligitalipeople
Yes the phone does charge when plugged in. I can't flash using Heimdall or Odin. Any other way of flashing?
I have also put the phone into debug mode with no luck.
Have you done a factory reset?
Yes, I have done a factory reset.
FINALLY! I got it to work.
Can you post back here and tell us what you did to get it working in case someone else has the issue?
Thanks and glad you got it going!
I am not sure what made it work for me. But what I did was "clear memory" on ram. I don't remember how I got onto that screen but I clicked on ram and clear memory.
I then pushed the usb into the pc a few times really fast until pc showed somethnig other than "usb device not recognized". Pc then started to show device connected.
if you are using windows i have found that sometimes the usb ports u used for the phone get stuck to the driver that was there in the first place. So what I do to fix this is go into device manager from the control panel and then uninstall the drivers for the specific port that I am trying to use. While keeping my phone unplugged from the computer I then reinstall the samsung drivers, restart my computer and then try to plug my phone in. 90% of the time that has been what works for me.
Ok, I figured out the problem. It has nothing to do with the drivers or clearing ram memory. My problem is the actual micro usb connection. If is a little loose from side to side and when I push it to one side, it connects no problem.
That is the exact same thing that happened to my wife's phone... luckily it was still under warranty...
Sent from my SGH-T959V using Tapatalk
My phone is out of warranty. At least now I know the problem. It was extremely frustrating trying to figure it out.
So my girlfriends little brother gave me his skyrocket. He asked me to backup his pics, which I did with no problem. I then did a factory reset. After that, my computer does not recognize the phone! I've tried different cables, different computers. My girlfriend has the exact same phone, connects right away.
I even flashed it with a different rom and put ICS on it. No luck! I then proceeded to take it to a phone repair place, thinking it might be the actual usb port. They said they checked out the port, and it look fine. All solder joints were good, no bent pins.
The weird thing is, is that it connects on an average of 1/20 times! It charges perfectly too. The phone doesn't go in and out of charge mode if i wiggle the cable either. I'm kind of confused! Is there a file on the phone that tells the computer what it is when connected? If so, can I manually replace that file? WHAT DO I DO!
When you goto recovery mode can you goto mounts and say mount usb? and does the pc recognize it then?
Sent from my SAMSUNG-SGH-I727 using xda premium
Kind of. We had trouble with it when flashing it. I personally didn't flash it. I watched my friend do it
Sent from my SAMSUNG-SGH-I727 using XDA
You could try installing the drivers again..
You mean on the computer? I did that. No luck. It does connect more often though WITH the drivers.
I had some problems with USB connectivity too. Using the cable that the Skyrocket came with solved my issues.
Have you tried any combination of restarting and reinstalling the drivers?
Swyped from my Nook Tablet, running CM7.
Yes. I've tried multiple cables including the stock cable. Installing drivers, restarting both devices. I have definitely ruled out the cable, the PC ( PC's actually), and the physical USB port.
Sent from my SAMSUNG-SGH-I727 using XDA
I had similar issues, messed with phone for a bit and came up with this
System settings>more>USB utilites
Now I got a screen that says USB mass storage with a button that says Connect storage to PC. Tap Button.
A window will pop up asking to Turn off USB debugging (if on) Tap OK
Connect USB cable to storage (plug USB cord into PC).
You should now be at the USB Mass Storage screen, Tap button at bottom (Turn on USB storage)
I found this to be the way to turn on Mass Storage since I flashed ICS, I believe. Hope this helps you, it took me a little while to figure out.
ChillFactorz said:
I had similar issues, messed with phone for a bit and came up with this
System settings>more>USB utilites
Now I got a screen that says USB mass storage with a button that says Connect storage to PC. Tap Button.
A window will pop up asking to Turn off USB debugging (if on) Tap OK
Connect USB cable to storage (plug USB cord into PC).
You should now be at the USB Mass Storage screen, Tap button at bottom (Turn on USB storage)
I found this to be the way to turn on Mass Storage since I flashed ICS, I believe. Hope this helps you, it took me a little while to figure out.
Click to expand...
Click to collapse
Of course, that's how it's always been except in a slightly different location on ICS
I've tried that also. Didn't work
Sent from my SAMSUNG-SGH-I727 using XDA
it basically sounds like the USB port on the phone is dead. Warranty that sucker
I took it to a repair shop. They said the port was perfectly fine!
Sent from my SAMSUNG-SGH-I727 using XDA
Not to mention that it was working perfectly before I did the factory restore
Sent from my SAMSUNG-SGH-I727 using XDA
how exactly did the repair shop test it?
try plugging it into another usb port on the same computer or try using a different computer. It could be the usb port on the PC itself.
gokartracer5 said:
try plugging it into another usb port on the same computer or try using a different computer. It could be the usb port on the PC itself.
Click to expand...
Click to collapse
That's the first thing he tried, it's in the OP
yeah i've tried everything! The repair shop determined that the port was good by examining it under a scope and they also said they tried re-flowing the solder joints. They said they wanted to stay away from replacing the usb port because it was very difficult to replace, not to mention they didn't warranty the job!
Someone has to know the answer to this!
Sent from my SAMSUNG-SGH-I727 using XDA
if its still under warranty replace it, thats all u can do. No one else in this forum besides u can physically touch the phone, so if you've tried all suggestions thats all thats left
i have the same problem but mine is little different, when i power off the phone it keeps on going to download mode, i keep on restarting it and it goes back to download mode, i flash stock rom and it does the same, i flash ics rom and it keeps on doing the same can anyone help?
So this issue started a few days ago. Any time I plugged my phone in it would constantly connect and disconnect from the pc. I've tried multiple usb cables, ports, and the 3 PCs I have with the same result on each. Now when I plug it in, it is no longer being recognized by the PC, Odin, ADB, etc... It will charge but that is it.
I have a warranty replacement coming to me however I need to be able to get this one back to stock... Any suggestions?
Before anyone asks, NO it has never been wet, dropped, damaged in any way, set on fire, caught in a land slide, earthquake, what have you.. The phone itself functions perfectly fine. All drivers are up to date, none of my PCs configurations have changed. I have one I use specifically for app development and not even that one will see the phone.
I had the same problem. I used a different cable and it all worked better....now with that said it happened again so I flashed my phone back to stock and all was well.
Then went to flashing ROMS.
Sent from my SAMSUNG-SGH-I727 using xda premium
Really check out the micro usb cable. A bad cable will just about always allow a device to charge, but data transfer is another story. If you really have tried a few micro USB cables, then it the problem relies elsewhere. Try restarting both phone and PC, and if neither works, sounds like you have a busted port on the Skyrocket.
Thank you both for your responses. I am a PC technician so I followed my usual troubleshooting steps to figure this out. I narrowed it down to either all of my cables are bad (not a chance) or the phone is just f**ked (likely). Ah well ill have to try to use another way to force the stock firmware and recovery on here. Lol
HTC = Hate The Consumer
I use my old Nokia OEM USB cable. Connects with the right number of pins on the USB connection end. I'd check your USB cables for # of pins . Skyrocket uses 5 I believe. Also that there is sufficient power to your USB ports. Aka avoid front USB ports which could only be 4 pin....
Sent from my I727 rocket on Marz! @[email protected]
When you plug the usb cable in, do you see the usb icon at the top left of your screen? I have to pull that window down to tell it to connect to pc, then confirm it again before mine connects. Mine doesn't auto connect on its own.
I see you've been a member for a few years so if its not connecting, that really sucks man. Hope you get it figured out.
Sent from my SAMSUNG-SGH-I727 using xda premium
Your phone is a ghost.
Sent from my HTC One X
Not running the AOKP ROM are you? The R3 build had an issue with this, and all AOKP will disable USB to PC if you enable 'fast charge' under ROM Control...
Good luck :S
According to what I've been reading you can try using the *#7284# code and setting the USB portion from PDA to MODEM and then back to PDA and it would kickstart the connection. No dice for me though. Ive been through 7 different USB cables already.. I am not about to go and buy one just to keep playing with it my other phones connect just fine using the same cables. No, I am running the latest Sky ICS
When I plug my USB cable into my computer and then into my phone the phone does not recognize the computer and vice versa. It will charge, but that is it. A few weeks ago I tried an AOKP rom which has "fast charge" I set this setting to be on to test it out and then turned it off. Ever since then I have not been able to transfer files with the cable plugged in, so I used AirDroid to wirelessly do it. I remember something in the warning about it, but I thought when you format/wipe and flash a new rom it corrects the issue. I have flashed a completely new rom since then and still nothing. Any help would be nice, thanks.
Try going back to stock through Odin or heimdal
Sent from my HTC PH39100 using XDA
How are you supposed to Odin/heimdall, if it doesn't connect even during download mode?
Sent from my SAMSUNG-SGH-I997 using xda premium
Lol didn't think of that...when I had my infuse I had the same problem with the stock USB cable...after a while data transfer stopped and it became a charge only cable...I would use my dads cable that worked perfect for data transfer...
So try a different USB cord or try a different USB port...
Sent from my HTC PH39100 using XDA
You can try this too
Hi, I faced this issue few times and tried several options like change cable/port/computer and worked.
One thing Recently i noticed when all of the above failed in my case is :- 1 Development->Uncheck the USB debug mode, 2. Check Mass Storage in USB connection setting. ( you need to unplug usb cable while doing it)
Now try connecting and give few minutes. If you can see the USB mass storage notification you are good to go. Go back and change the Debug mode as Checked.
It worked for me couple of times hope it may work for you too.
Cjohns8792 said:
When I plug my USB cable into my computer and then into my phone the phone does not recognize the computer and vice versa. It will charge, but that is it. A few weeks ago I tried an AOKP rom which has "fast charge" I set this setting to be on to test it out and then turned it off. Ever since then I have not been able to transfer files with the cable plugged in, so I used AirDroid to wirelessly do it. I remember something in the warning about it, but I thought when you format/wipe and flash a new rom it corrects the issue. I have flashed a completely new rom since then and still nothing. Any help would be nice, thanks.
Click to expand...
Click to collapse
Sounds like the dreaded USB port failure. Many Infuse users have gone through this as its a known issue. I returned mine and got a replacement via warranty.
Cjohns8792 said:
When I plug my USB cable into my computer and then into my phone the phone does not recognize the computer and vice versa. It will charge, but that is it. A few weeks ago I tried an AOKP rom which has "fast charge" I set this setting to be on to test it out and then turned it off. Ever since then I have not been able to transfer files with the cable plugged in, so I used AirDroid to wirelessly do it. I remember something in the warning about it, but I thought when you format/wipe and flash a new rom it corrects the issue. I have flashed a completely new rom since then and still nothing. Any help would be nice, thanks.
Click to expand...
Click to collapse
Hey There,
We had the same issue with many units and solved all by doing the following:
-Flashing the unit back to stock
-Performing a factory data reset after flashing(This is a must)
Note: Even though your device will not connect to the computer in PDA mode you should still be able to connect in download mode so it can be flashed with ODIN.(Unless if it's hardware related)