Related
Purchased a gtablet, all went smooth after I installed the TNT Rom, but found some sound issues, and found out that seemed to plague a lot of other people, so decided to try another ROM - can't even recall which one now. But now where I'm stuck at is if I hold down vol up and power, I get "Recovery key detected Booting recovery kernel image" and it sits there forever. Even if I take out the microsd card, I get the same screen. A normal power attempt sits forever at the Viewsonic "birds" screen. I've tried just about every rom, none take . I'm pretty sure I had the clockwork recoverymod installed, but now I can't even get into that.
I tried volume down + power, (ATP mode?) but none of the drivers I've found are for Windows 7 64 bit, so I can't access the tablet in that mode because the lack of drivers.
Any suggestions on what to do from here?
Thanks!
http://forum.xda-developers.com/showthread.php?t=989320&highlight=nvflash+windows
Good Luck
http://forum.xda-developers.com/showpost.php?p=9302497&postcount=5
Bottom of instructions section -- a few users have written posts on nvflash for windows.
LGCubana said:
http://forum.xda-developers.com/showthread.php?t=989320&highlight=nvflash+windows
Good Luck
Click to expand...
Click to collapse
Hi,
Thanks for the link.. I think I've seen that - I don't see a APX driver missing in Device Manager - there is a ADB Interface, however when I let that install drivers, it says the Device cannot start - Code 10.
I may have another computer I can boot up and try
phirephoto,
I wrote the USB post and used the files there to NVFlash in APX mode. I know the info there is accurate.
I also have found, however, that if you install the whole SDK kit instead of the files in my post, it installs ADB. I don't know much about ADB but I know it basically works about the same.
If you have the APX driver it says it is the nVidia USB driver in Device Manager. So I am assuming you have installed SDK.
I can only suggest you make sure what files are installed on your PC and what method you are using and then research this site. I know several people have used the ADB methods and posted about them.
Good luck.
Rev
If you have another computer -- try the method reobeet posted along with the Advent Vega USB files. I know that has worked.
butchconner said:
phirephoto,
I wrote the USB post and used the files there to NVFlash in APX mode. I know the info there is accurate.
I also have found, however, that if you install the whole SDK kit instead of the files in my post, it installs ADB. I don't know much about ADB but I know it basically works about the same.
If you have the APX driver it says it is the nVidia USB driver in Device Manager. So I am assuming you have installed SDK.
I can only suggest you make sure what files are installed on your PC and what method you are using and then research this site. I know several people have used the ADB methods and posted about them.
Good luck.
Rev
If you have another computer -- try the method reobeet posted along with the Advent Vega USB files. I know that has worked.
Click to expand...
Click to collapse
It did work on my old POS XP Laptop I knew that thing was useful for something!
Thanks again.. Never thought I'd be so happy to see "TapnTap" again. And now I'm up and running on the Vegan rom
i've just flashed prime 1.9 mobile data ver over CWM. have to say the whole proccess ended faster then normal. after rebooting i get nothing. black screen.
tried holding power for 10-20 sec, even 30. nothing.
so tried going into APX mode and nvflashing through pc. but when i'm doing that the pc recognizing it as "unknown device" and not an APX.
so i've realy got nothing. and i cant communicate with pc to nvflash.
obviously i tried manualy install APX driver from nvflash folder. but still get unknown device.
please help!
what should i do?
im not a newbie i've done those things dozens of times. (nvflash, apx, cwm..) but i've never faced a totall brick
so you already had nvflash connected to device before it is bricked so you are sure all is setup corectly ?
cause it is a real pain in the but that when the tf is in apx it just looks dead.
If that is the case than I dont have a clue because nvflash is kind of a last resort
Uninstall the drivers, reboot, install the drivers again and try for apx, if its a no go then reboot pc and try for apx.
Sorry i cant be more help.
Edit - Make sure the TF actually has some juice in it. Leave it on charge for a couple of hours.
i've done nvflash before and i'm familiar with the procedure.
about uninstalling drivers and rebooting, maybe will help altough i've tried going into apx with other computers with no success aswell.
please help!
no one knows maybe theres a reset button or something inside the transformer. just a way to bring APX back!
if you can get back into revovery, try to flash again.
check md5sum yo make sure you have a good file
Sent from my Transformer TF101 using Tapatalk
thats the thing. ive got nothing. the screen just stays black no matter what. so i thought maybe APX will rescue me but i now dont have even APX. is it even possible?
apx mode on ming leaves the screen blank and off. leave your tablet on a charger for a while to make sure it is charged, a couple of hours at least reduce as many errors as you can. if you have the apx drivers installed right when you plug it in to windows you will hear a beep saying you plugged a device in. You could also try to install the apx drivers again.
http://forum.xda-developers.com/showthread.php?t=1123429
this will tell you how to do it.
http://forum.xda-developers.com/showthread.php?t=1185104
this thread has better instructions though.
have you ever installed nvflash drivers before...or is this the first time?
ive already told yall. i done this proccess before (nvflash and going into APX. i know the screen should stay off and only the computer should say APX device been detected or something like that. but the message im getting from pc is "unknown device" connected. and when i try to manually install the apx drivers from device manager by directing it to the nvflash folder where the drivers should be- it just stays unknown device and says that the most updated drivers for it is already installed
I'm having the same issue. I can't get into APX mode anymore. Just appears as "Unknown Device" in device manager.
I'm currently running PRIME 1.7. My clockwork recovery also fails to recognize the SD card, so I can't flash a new ROM that way either. I really want to switch to Revolver, but with no APX, it's not going to happen.
hmm maybi you can try it on a other pc. if you have luck it can be recognizedd
Unknown Device......?
Uninstall the drivers, reboot pc, reinstall fresh drivers, reboot pc, connect TF101
Next time use the search function or google.
Hey everyone first this is a great place full of info, I just get and Trio stealth pro 7 by mach speed technology, I rooted it, I intalled CWM without problems, I also flash CM9 without any problem, but I change CPU values, to min=900MHz max=1200MHz something like that and after that a turn off the tablet then when I turn on again it just freeze in lock screen after boot. and I can't go to recovery mode with hardware bottons, Sorry for my english I'm from Venezuela. thanks any help.
Joshdmo said:
Hey everyone first this is a great place full of info, I just get and Trio stealth pro 7 by mach speed technology, I rooted it, I intalled CWM without problems, I also flash CM9 without any problem, but I change CPU values, to min=900MHz max=1200MHz something like that and after that a turn off the tablet then when I turn on again it just freeze in lock screen after boot. and I can't go to recovery mode with hardware bottons, Sorry for my english I'm from Venezuela. thanks any help.
Click to expand...
Click to collapse
You can get into recovery via ADB, Download the USB drivers for your device and then get the Android SDK tools, you can read up how to do that, then get into your platform tools folder, get a cmd prompt going, turn it on, and type "adb reboot recovery" as fast as you can before it freezes.
orangekid said:
You can get into recovery via ADB, Download the USB drivers for your device and then get the Android SDK tools, you can read up how to do that, then get into your platform tools folder, get a cmd prompt going, turn it on, and type "adb reboot recovery" as fast as you can before it freezes.
Click to expand...
Click to collapse
Thanks man, I now downloading the android SDK tools, but i can't find the usb driver, but i think my pc already has it installed because I rooted my tablet from here with unlockroot, anyways I will get it a shout and I let you now if i need some help, thenks for the answer so fast.
Joshdmo said:
Thanks man, I now downloading the android SDK tools, but i can't find the usb driver, but i think my pc already has it installed because I rooted my tablet from here with unlockroot, anyways I will get it a shout and I let you now if i need some help, thenks for the answer so fast.
Click to expand...
Click to collapse
yeah bro, let us know if it worked
Ok bro i did install the sdk and the plataformtools how i open the adb sorry i'm kind of noob in this sdk stuff
Sent from my LG-P500 using xda app-developers app
Ey man thanks for the help, I install recovery from ADB shell but for some reason every time i reboot my tablet the recovery is gone, so i restore stock rom but the touch is nota working and now i can't connect to adb because debugging mode is off in the tablet, any ideas? Please bro and thanks for the help
Sent from my LG-P500 using xda app-developers app
Hello. I have the same problem but where do you get the stock firmware?
Sent from my Xperia Mini Pro using xda app-developers app
Stealth Pro
siuishere said:
Hello. I have the same problem but where do you get the stock firmware?
Sent from my Xperia Mini Pro using xda app-developers app
Click to expand...
Click to collapse
Don't know if you're still having the same problem but if so, you're in luck. I have the same tablet, what I did to restore mine was to download livesuit to flash a recovery image onto your device. Of course everything will be deleted but once you're back into your tablet you can put all your apps back on &/or your custom rom. I was able to get CM10 onto mine running very smoothly so I recommend iit.
Anyway, use the recovery image for the ly-f1 tablet. It's exactly like the stealth pro trio tablet so you can use the same things. Just google "ly-f1 recovery image" download a good one and open it up in livesuit. After that you're gonna wanna put your tablet into download mode.To do that you wanna make sure the tablet is off. Plug your usb in. Press and hold the volume down button on your tablet while pressing the power button about 10 times or at least until you hear your computer respond. Livesuit will guide you there rest of the way. It's really simple.
GOOD LUCK.
YannaMariex said:
Don't know if you're still having the same problem but if so, you're in luck. I have the same tablet, what I did to restore mine was to download livesuit to flash a recovery image onto your device. Of course everything will be deleted but once you're back into your tablet you can put all your apps back on &/or your custom rom. I was able to get CM10 onto mine running very smoothly so I recommend iit.
Anyway, use the recovery image for the ly-f1 tablet. It's exactly like the stealth pro trio tablet so you can use the same things. Just google "ly-f1 recovery image" download a good one and open it up in livesuit. After that you're gonna wanna put your tablet into download mode.To do that you wanna make sure the tablet is off. Plug your usb in. Press and hold the volume down button on your tablet while pressing the power button about 10 times or at least until you hear your computer respond. Livesuit will guide you there rest of the way. It's really simple.
GOOD LUCK.
Click to expand...
Click to collapse
Can you tell me where would I find the Image files. I tried to using the livesuite i keep getting invalid img file with files that i have
trio7-a10-bma250-stockimg
and
trio7-a10-mxc622x-stockimg
Joshdmo said:
Hey everyone first this is a great place full of info, I just get and Trio stealth pro 7 by mach speed technology, I rooted it, I intalled CWM without problems, I also flash CM9 without any problem, but I change CPU values, to min=900MHz max=1200MHz something like that and after that a turn off the tablet then when I turn on again it just freeze in lock screen after boot. and I can't go to recovery mode with hardware bottons, Sorry for my english I'm from Venezuela. thanks any help.
Click to expand...
Click to collapse
Hi, I'm kinda of a noob at this stuff, but I've learned quite a bit recently from just reading around, so bear with me if I don't understand or need more specific instructions. I have the trio stealth pro 7 and it is always stuck on the boot screen with the android logo when I boot. I was attempting to flash cm9 on the tablet but after I wiped the tablet initially, i couldnt find the cm9 rom on my internal memory while in recovery mode, so I ended up turning off my tablet, which now doesn't boot up anymore (stuck with android logo). I found a fix where you can use livesuite and adb to fix this issue; however, after installing adb, my tablet is not being detected, (my phone does). My tablet is not being recognized by windows in general, and it doesn't show up under device manager. There was one part of the step where I need to install usb drivers for the tablet; however, I cant find any online. I have used the tablet before with my computer before the attempt to flash cm9, so I am guessing drivers should already be installed. I feel I can get this issue fixed if I can just get adb to recognize my tablet. Perhaps this fix is not the one I need and maybe there's a simpler fix. I'm just too dumb to have realized it. Another note to add is, pressing the combination of power and volume buttons does nothing. Please help!!! thank you!!
stock images download
Hi guys ... Trio tablet Is similar or the same as Ly-F1 tablets :cyclops: these stock images will work and can be downloaded from link bekow.. make sure you download live suite first, applicable drivers (adb/fastboot) and you should be good . Follow directions accordingly and as reminder ,, :highfive: ,,, flashing / adb / sdk should only be used by advanced users who are comfortable using the SDK ADB flash tools.. . I am in no way responsible for bricked devices... Happy Flashing. :cyclops:
http://lyxfsz.com/en/downs.htm?sortid=0_22 Downloads LINK
Good day, I am new here as a member. I think I bricked my TF101. The other day I installed 2 apps from play store if i remember it it was yousendit. I am running on stock ICS. then it just automatically turned off. i tried to turn it on again but when it goes into the asus screen with circling dots it just turns off again. tried cold booting it, still the same. then i used wipe data. but an hour has past still my tablet is still showng the android with a rotating orb in its belly. so last night i downloaded every tool i could research. first i tried PERI but it says it does not recognize my device, then i use brks tool v8, i tried installing stock rom as instructed, no success. then i tried easy flasher today and now i cant even see the first boot screen.
I hope you can help me, i use this tablet at work and presentation to my clients. I am new with this OS and seems that i wrecked my tab by solving it myslef, I hope this was not the case. BTW i have a B60 tf101. i bought it second hand with my savings so i have no warranty.
can you please give me a step by step solution, i am very desperate here, thank you.
blitz_krieg916 said:
Good day, I am new here as a member. I think I bricked my TF101. The other day I installed 2 apps from play store if i remember it it was yousendit. I am running on stock ICS. then it just automatically turned off. i tried to turn it on again but when it goes into the asus screen with circling dots it just turns off again. tried cold booting it, still the same. then i used wipe data. but an hour has past still my tablet is still showng the android with a rotating orb in its belly. so last night i downloaded every tool i could research. first i tried PERI but it says it does not recognize my device, then i use brks tool v8, i tried installing stock rom as instructed, no success. then i tried easy flasher today and now i cant even see the first boot screen.
I hope you can help me, i use this tablet at work and presentation to my clients. I am new with this OS and seems that i wrecked my tab by solving it myslef, I hope this was not the case. BTW i have a B60 tf101. i bought it second hand with my savings so i have no warranty.
can you please give me a step by step solution, i am very desperate here, thank you.
Click to expand...
Click to collapse
Easy flaher is the way out,
1) Download universal naked driver and unzip into a folder
2) Download latest Asus transformer firmware and put it in firmware folder.
3) Uninstall all Asus drivers from your laptop.
4) Disconnect your laptop from WiFi/internet and make it offline
4) Now plug your tablet and let windows install required driver.
5) If windows cannot install driver( mostly it won't as laptop is not connected to the net) then use "manually install driver" option and select the folder where you downloaded and unzipped "universal naked driver" and that should install the naked driver.
6) If that doesn't then goto device manager, there you should see unknown device, select it and update the driver manually.
7) Once the driver is installed, then unplug the tablet
8) now connect the tablet back and press volume up and power button together till laptop starts installing APX driver.
9) If it doesn't then try repeating step 5 or step 6 and that will install APX driver.
10) Launch EASY FLASHER and unroot and install stock ROM...
Good luck
Sent from my Transformer using xda app-developers app
udupa82 said:
Easy flaher is the way out,
1) Download universal naked driver and unzip into a folder
2) Download latest Asus transformer firmware and put it in firmware folder.
3) Uninstall all Asus drivers from your laptop.
4) Disconnect your laptop from WiFi/internet and make it offline
4) Now plug your tablet and let windows install required driver.
5) If windows cannot install driver( mostly it won't as laptop is not connected to the net) then use "manually install driver" option and select the folder where you downloaded and unzipped "universal naked driver" and that should install the naked driver.
6) If that doesn't then goto device manager, there you should see unknown device, select it and update the driver manually.
7) Once the driver is installed, then unplug the tablet
8) now connect the tablet back and press volume up and power button together till laptop starts installing APX driver.
9) If it doesn't then try repeating step 5 or step 6 and that will install APX driver.
10) Launch EASY FLASHER and unroot and install stock ROM...
Good luck
Sent from my Transformer using xda app-developers app
Click to expand...
Click to collapse
thanks i will try this immidiately. my laptop is ancient. hopefully i will do it right this time.ill let you know the development
Sir i still cant get it to work i followed your instruction.
BTW here are my details. I guess I downloaded the correct update.
TF101
B60KAS1245548
16gb
I am using an old HP laptop with XP as OS. And I adownloaded this from the asus website and placed it in the folder inside the easy flasher folder WW_epaduser9_2_1_27UpdateLauncher.zip.
Thanks in advance.
blitz_krieg916 said:
Sir i still cant get it to work i followed your instruction.
BTW here are my details. I guess I downloaded the correct update.
TF101
B60KAS1245548
16gb
I am using an old HP laptop with XP as OS. And I adownloaded this from the asus website and placed it in the folder inside the easy flasher folder WW_epaduser9_2_1_27UpdateLauncher.zip.
Thanks in advance.
Click to expand...
Click to collapse
I tihnk a PART of your issues is that you got the wrong file. Instead of the WW version you should be using the US_epaduser file. This is of course thinking that you are in the USA.
I downloaded the WW version thinking that the pad was bought here in the Philippines (second hand). Or maybe I am wrong. Thanks for the idea I'll download the other update and give it a try.
You have a B60 tablet, just use NvFlash via APX mode manually. Much less room for error than anything else IMO, first download image from here http://xdafileserver.nl/index.php?dir=Asus/Asus+Transformer+(TF101)/STOCK+ROMS/ICS+.27
Pick WW for ww tablet, or US for us tablet. (I believe yours will be a US tablet, purchased in the Philippines)
Then download wheelie (NvFlash tool) from androidroot.mobi. Copy and paste the files into the other folder you downloaded earlier, overwrite everything with the newer wheelie files.
Put TF into APX mode (Power off, hold volume up while plugged into computer, power back on, screen will remain black and computer should detect device in APX mode.)
Run Reflash_sbkv1.bat (make sure it is sbkv1 not sbkv2 as you have a B60)
If runs successfully you should be unbricked.
You can then reroot with PERI or other if desired.
blitz_krieg916 said:
thanks i will try this immidiately. my laptop is ancient. hopefully i will do it right this time.ill let you know the development
Click to expand...
Click to collapse
It doesn't matter what version of Asus you download ( I'm in US and I downloaded WW version), but can you explain what problems you facing while you try to follow the steps I mentioned... also screen shot of laptop would help I have bricked my tablet at least 10 times and easy flasher (wheelie) always brought it back....
Sent from my Transformer using xda app-developers app
udupa82 said:
It doesn't matter what version of Asus you download ( I'm in US and I downloaded WW version), but can you explain what problems you facing while you try to follow the steps I mentioned... also screen shot of laptop would help I have bricked my tablet at least 10 times and easy flasher (wheelie) always brought it back....
Sent from my Transformer using xda app-developers app
Click to expand...
Click to collapse
Pics and more info would help ^^
Easy flasher *should* work, from what I've heard of it.
I was wondering what's supposed to happen after I launch sbkv1, my tablet just seems to disconnect and the screen stays black.
im trying on whellie tonight
so here are my screenshots. i downloaded from the link you gave me, and downladed wheelie then extracted wheelie on the same folder as the rom. clicked on reflash sbkv1 and on to the next screenshot, how many minutes sholud i wait for it, it says done, but when i switch on my TF nothing happens.
I followed again the whelie using the US and this happened. will it automatically boot my TF or should i manually boot it?
I also used easyflasher and i got stuck with this? what am I doing wrong?
guys i found the box of my TF and shot a pic of the serial number just to be sure.
i researched a bit on other forums and i think im in an permanent apx loop which some say is unsolvable. is this true? i hope not.
blitz_krieg916 said:
I also used easyflasher and i got stuck with this? what am I doing wrong?
Click to expand...
Click to collapse
As far as I can understand, your laptop is recognizing your tablet in APX mode otherwise easy flasher won't work. So plug it back in apex mode and click on "flash Asus stock zip" it will push stock unrooted Asus rom, WAIT for it to finish, it might take some time but WAIT!!! Once its totally finished then you can reboot into a stock ROM.... WAIT for EASY FLASHER to finish.
if you like to root again then use the same to flash recovery and superuser
Sent from my Transformer using xda app-developers app
Thank you for your reply sir. I waited but it seems the while flashing as shown on the screen the TF gets disconnected. I counter check it on the device manager and the "nvidia boot reccovery" was not showing.
It never happened to me, it takes time but it always pushed stock zip through, if that's not happening then I'm out of ideas. I'm sorry to say I'm out of ideas. But sometime back I saw some where, some one suggested a way to unbrick using ADB, I'm not not sure how to ho about it, search the forum, you might find it.. good luck
Following is the last option if nothing else helps and no one can provide you an answer then try following
Instead of flashing Asus stock ROM, Use easy flash to push twrp recovery, i know its not conventional but if you get recovery then you can flash a custom rom... GOOD LUCK
Sent from my Transformer using xda app-developers app
udupa82 said:
It never happened to me, it takes time but it always pushed stock zip through, if that's not happening then I'm out of ideas. I'm sorry to say I'm out of ideas. But sometime back I saw some where, some one suggested a way to unbrick using ADB, I'm not not sure how to ho about it, search the forum, you might find it.. good luck
Following is the last option if nothing else helps and no one can provide you an answer then try following
Instead of flashing Asus stock ROM, Use easy flash to push twrp recovery, i know its not conventional but if you get recovery then you can flash a custom rom... GOOD LUCK
Sent from my Transformer using xda app-developers app
Click to expand...
Click to collapse
Thank you very much sir for your time and to all that replied to this problem. It really disconnects after formatting the 10th partition. I researched on how to use the ADB and that requires a lot more knowledge on programming. I will still try the last option, im crossing my fingers it will work or else ill call the asus service center her in the Philippines. Hopefully they can fx it and it wont be an expensive fix. Thanks again!
Afternoon guys,
Before anyone has a go at me, I've have spent about five hours looking through this forum for what I'm looking for and i've tried all the easy unroot/easy flasher/etc and got all the stock Asus rom and recovery. AND the forum search is temporarily unavailable.
So here is what I have:
ClockworkMod Recovery v5.8.3.4
Liquid Smooth Rom
I have installed the stock rom, recovery and wiped everything.
If i press the power button it loads into CWM recovery.
If i press power and down vol, it loads to the wipe data/load android screen, and which it hangs on forever,
So I guess what im asking you good people of the internet is:
A) How do I finally get rid of CWM Recovery (because even if i install another recovery it boots back to CWM), and
B) How on gods earth do I get back to stock?
Now I know people are going to be like search the forums, I have, and I've tried literally everything that everyone has posted, and clearly while it's worked for millions of other people, my tablet is retarded and doesnt want to follow the norm.
Also i am the greatest noob ever.
Any help would be greatly appreciated.
Thanks
Hmmm, did you unzip the stock ROM once before flashing (it will still be a zip).
Otherwise, try using EasyFlasher and APX mode. For EasyFlasher, do not unzip the stock ROM, use it as it downloads from Asus.
killerkuk said:
Afternoon guys,
Before anyone has a go at me, I've have spent about five hours looking through this forum for what I'm looking for and i've tried all the easy unroot/easy flasher/etc and got all the stock Asus rom and recovery. AND the forum search is temporarily unavailable.
So here is what I have:
ClockworkMod Recovery v5.8.3.4
Liquid Smooth Rom
I have installed the stock rom, recovery and wiped everything.
If i press the power button it loads into CWM recovery.
If i press power and down vol, it loads to the wipe data/load android screen, and which it hangs on forever,
So I guess what im asking you good people of the internet is:
A) How do I finally get rid of CWM Recovery (because even if i install another recovery it boots back to CWM), and
B) How on gods earth do I get back to stock?
Now I know people are going to be like search the forums, I have, and I've tried literally everything that everyone has posted, and clearly while it's worked for millions of other people, my tablet is retarded and doesnt want to follow the norm.
Also i am the greatest noob ever.
Any help would be greatly appreciated.
Thanks
Click to expand...
Click to collapse
If your TF is SBK1 (Serial B6O or earlier, some B7Os work too) you can use NVFlash
http://www.xdafileserver.nl/index.php?dir=Asus/Asus+Transformer+(TF101)/STOCK+ROMS/ICS+.27
Stick the TF into APX mode (Vol up & Power from Powered Off state)
Run download.bat as Admin (Right click > Run as Admin)
@frederuco
I did unzip it and install it. It still hangs.
I tried EasyFlasher, but for some reason I run through it and the process completes, when i reboot the tablet nothing has changed.
@*Detection*
I can't get the link to work for some reason.
Thanks for your help so far, but stupid tablet stays stupid!
killerkuk said:
@frederuco
I did unzip it and install it. It still hangs.
I tried EasyFlasher, but for some reason I run through it and the process completes, when i reboot the tablet nothing has changed.
@*Detection*
I can't get the link to work for some reason.
Thanks for your help so far, but stupid tablet stays stupid!
Click to expand...
Click to collapse
Try the direct links here
WW and US in that order
Code:
http://www.xdafileserver.nl/Files/Asus/Asus%20Transformer%20(TF101)/STOCK%20ROMS/ICS%20.27/NVFLASH_ICS_9.2.1.27_WW_NOROOT.7z
http://www.xdafileserver.nl/Files/Asus/Asus%20Transformer%20(TF101)/STOCK%20ROMS/ICS%20.27/NVFLASH_ICS_9.2.1.27_US_NOROOT.7z
Otherwise go to http://www.xdafileserver.nl and navigate to stock ROMs section
*Detection* said:
Try the direct links here
WW and US in that order
Code:
http://www.xdafileserver.nl/Files/Asus/Asus%20Transformer%20(TF101)/STOCK%20ROMS/ICS%20.27/NVFLASH_ICS_9.2.1.27_WW_NOROOT.7z
http://www.xdafileserver.nl/Files/Asus/Asus%20Transformer%20(TF101)/STOCK%20ROMS/ICS%20.27/NVFLASH_ICS_9.2.1.27_US_NOROOT.7z
Otherwise go to http://www.xdafileserver.nl and navigate to stock ROMs section
Click to expand...
Click to collapse
Much appreciated! :good:
Fingers crossed this works!
*Detection* said:
If your TF is SBK1 (Serial B6O or earlier, some B7Os work too) you can use NVFlash
http://www.xdafileserver.nl/index.php?dir=Asus/Asus+Transformer+(TF101)/STOCK+ROMS/ICS+.27
Stick the TF into APX mode (Vol up & Power from Powered Off state)
Run download.bat as Admin (Right click > Run as Admin)
Click to expand...
Click to collapse
I downloaded it and ran it as admin, DOS flashed up and disappeared before i could read what it said.
the nvflash app does the same, even when i run as admin.
maybe this is a lost cause..
killerkuk said:
I downloaded it and ran it as admin, DOS flashed up and disappeared before i could read what it said.
the nvflash app does the same, even when i run as admin.
maybe this is a lost cause..
Click to expand...
Click to collapse
What is the first 3 characters of your tablet serial?
And was it in APX mode connected to PC USB with APX drivers installed ?
*Detection* said:
What is the first 3 characters of your tablet serial?
And was it in APX mode connected to PC USB with APX drivers installed ?
Click to expand...
Click to collapse
The serial starts with B40.
Im on a mac (as i have no access to a pc) but have VMWARE running windows 7, with APX drivers on it.
When i put it in APX mode, it comes up that it is connected as Nvidia APX device.
Could this be where I'm going wrong?
killerkuk said:
The serial starts with B40.
Im on a mac (as i have no access to a pc) but have VMWARE running windows 7, with APX drivers on it.
When i put it in APX mode, it comes up that it is connected as Nvidia APX device.
Could this be where I'm going wrong?
Click to expand...
Click to collapse
Yea probably, I've never tried using NVFlash on anything other than a PC running Windows
Try updating the NVidia APX Device with these drivers
http://forum.xda-developers.com/attachment.php?attachmentid=1489867&d=1353190140
Chances are its the drivers running on the Mac that are causing the problem with the USB > VMWare > TF101
I know nothing about Mac, but I heard you can install Windows 7 almost natively using Bootcamp or something? Might be worth trying that if you can't do it in VMWare
*Detection* said:
Yea probably, I've never tried using NVFlash on anything other than a PC running Windows
Try updating the NVidia APX Device with these drivers
http://forum.xda-developers.com/attachment.php?attachmentid=1489867&d=1353190140
Chances are its the drivers running on the Mac that are causing the problem with the USB > VMWare > TF101
I know nothing about Mac, but I heard you can install Windows 7 almost natively using Bootcamp or something? Might be worth trying that if you can't do it in VMWare
Click to expand...
Click to collapse
thanks dude, looks like i need a trip to a friends house!
killerkuk said:
thanks dude, looks like i need a trip to a friends house!
Click to expand...
Click to collapse
Good luck!
*Detection* said:
Good luck!
Click to expand...
Click to collapse
Thanks for your help!
All sorted and back to stock. looks like it was an issue with the mac. plugged it into a pc and everything worked out fine!
WOOOOOOOOOOOOOOOOOOOOOOOOO!!!
killerkuk said:
Thanks for your help!
All sorted and back to stock. looks like it was an issue with the mac. plugged it into a pc and everything worked out fine!
WOOOOOOOOOOOOOOOOOOOOOOOOO!!!
Click to expand...
Click to collapse
Great!
At least you know now you can do what you like with it firmware / ROM / Recovery wise, and always be able to return it to stock, you can't break APX mode unless you physically damage the tablet