Help Needed!!! - HTC Sensation

Hi Guys,
I am new to this flashing ROMs, I have a HTC sensation and I used the Rovolutionary.io tutorial to S-Off my phone.
Since then I Downloaded the OTA Telstra ICS update as the current custom ROMs I have researched have had bugs with the WiFi tether (could be wrong).
I decided to use the OrDroid V9.0.0 ROM, but when I download the file from xda, It downloads it and does not stay zipped. I compress the file to .zip.
I tried to install the OTA and it comes up with the blue droid and white triangle and just freezes.
I then tried to install Ordroid through recovery and it gives me a message installation aborted. Please help as I cannot seem to update any way.
Cheers
Sent from my HTC Sensation Z710a using xda app-developers app

very strange! are you using the correct download link? when i ran ordroid i downloaded directly to my computer than i transfered to the root of my sd card by using the cable and running my device as disk drive.then i share the file to disk drive e which is my device. then i wipe data factory reset, wipe cash and dalvik, then install through recovery by choosing install zip , then reboot your device. did you do all these steps as ive shown? if so you should have no problem with the download or the zip file. if you do these steps their is no need to change the zip file in any way. It is correct the way it is. I hope this helps you ! Just follow the steps and it will work perfectly.
Always install through recovery! So download the way i have shown, go to recovery, wipe data factory reset, wipe cash and dalvik , stay in recovery, install zip from sd card, reboot. And your all set. Use this method every time. Pay attention to the way to download the zip. Its pretty straight foward. Download directly to computer. Run device as disk drive by checking disk drive. While your hooked up to your usb cable. Go to file shearing when it pops up on the computer, go to downloads, find your download, click share go to share with disk drive e. Then it will place the file to the root of your sd card. Then unplug. And follow flashing instructions i gave you in recovery.
Sent from my Sensation using xda premium

setted7 said:
Hi Guys,
I am new to this flashing ROMs, I have a HTC sensation and I used the Rovolutionary.io tutorial to S-Off my phone.
Since then I Downloaded the OTA Telstra ICS update as the current custom ROMs I have researched have had bugs with the WiFi tether (could be wrong).
I decided to use the OrDroid V9.0.0 ROM, but when I download the file from xda, It downloads it and does not stay zipped. I compress the file to .zip.
I tried to install the OTA and it comes up with the blue droid and white triangle and just freezes.
I then tried to install Ordroid through recovery and it gives me a message installation aborted. Please help as I cannot seem to update any way.
Cheers
Sent from my HTC Sensation Z710a using xda app-developers app
Click to expand...
Click to collapse
Howdy!
Did you download the file via your computer or via your phone? If it's via your computer just verify that the option to decompress your file aromatically is not tick, that is what could cause your file to decompress everytime you try.
See attachment.

Related

Rooting and Flashing a custom ROM

I flashed the leaked froyo firmware I897UCJI6 on my samsung captivate using odin 1-click method. I have a working 2.2 now. My phone is not rooted. I am planning to flash a custom ROM and try other custom ROMs out there in the market. I've gone through a three part video series by mobiletechvideos on how to root and flash a custom ROM (http://forum.xda-developers.com/showthread.php?t=884364). But, i still have a few questions.
1. For rooting, do i need to flash the phone back to the stock JF6?
2. In the xda link given above, i am fine until step #4. Step #5 is a little bit confusing to me. After i copy the root file to the root directory in the internal sd card on my phone, i rename it to update.zip. Also, i copy the clockworkrecovery to the root directory in the internal sd card in the phone and rename it to update.zip. Now, after i am doing with rooting and clockworkrecovery, i have to proceed further to flash the custom ROM. Now, the steps mentioned in the xda forum does not say anything about moving the custom ROM file to the root directory in the internal sd card on the phone. My question is: Do i need to copy the custom ROM zip file into the root directory of the phone? Do i need to rename the custome ROM file to update.zip as well?
Someone please help.
Yes rom goes on sd, no do not rename
If you are on ji6 you will not be able to install clockwork because of 3e recovery. Two option, flash back to stock using
http://www.fileserve.com/file/emnCn2j
One click odin, provided you are at&t and build number is 1009 and lower located under battery
2 look for modded 3e recovery in. development for captivate posted by exist
mcord11758 said:
Yes rom goes on sd, no do not rename
If you are on ji6 you will not be able to install clockwork because of 3e recovery. Two option, flash back to stock using
http://www.fileserve.com/file/emnCn2j
One click odin, provided you are at&t and build number is 1009 and lower located under battery
2 look for modded 3e recovery in. development for captivate posted by exist
Click to expand...
Click to collapse
Thanks for the reply. What is 3e recovery by the way? I am able to flash back to stock (jf6) using odin 1-click by following the volume up + down method to download. My build number is not in that 1000 series. Are you referring to s/n number found under the battery? In many threads I have seen ppl saying if u r under 1009 build # then you need to use 3 key combo method. You are saying the opposite. I am confused now. Sorry sir but I think I need.more explanation. I thank you for your time
Sent from my SAMSUNG-SGH-I897 using XDA App
Are you on at&t
If you can get into dl mode issuing volume and usb then you have three button combo. Later builds can not use jf6 stock 1010 and up. Your build had to be there, and I do not think it its possible it is not in the 1000s if you have a captivate
mcord11758 said:
Are you on at&t
If you can get into dl mode issuing volume and usb then you have three button combo. Later builds can not use jf6 stock 1010 and up. Your build had to be there, and I do not think it its possible it is not in the 1000s if you have a captivate
Click to expand...
Click to collapse
Pls clarify if s/n # found under battery is actually the build number. Also, according to many posts in this forum, three buttom combo is
1. Vol up
+
2. Vol down
+
3. Press Power button
Since when USB slot became a button? I am sorry but I dont understand.
Sent from my SAMSUNG-SGH-I897 using XDA App
Sorry for confusion
Recovery uses three burton combo
Volume up and down and power
Download mode uses volume up and down plug in usb
On your phone under battery left side under sn above sku there us your build. Mine is 1008
mcord11758 said:
Sorry for confusion
Recovery uses three burton combo
Volume up and down and power
Download mode uses volume up and down plug in usb
On your phone under battery left side under sn above sku there us your build. Mine is 1008
Click to expand...
Click to collapse
Thank you. Mine is 1007. So, now back to the question. I need to flash back to stock JF6 using odin 1-click. Then,i need to root the phone and install.clockworkmod recovery using the info found in the 3 part video series by mobiletechvideos. And,proceed with the custom ROM flash. Is my understanding correct? Thanks for replying patiently to all my queries. Thanks
Sent from my SAMSUNG-SGH-I897 using XDA App
No need to root when in stock.
Dl this
http://forum.xda-developers.com/attachment.php?attachmentid=464425&d=1292362952
This update zip gives you clockwork recovery.
When on stock put this on the root of your sd.
Phone off
Three button combo
When at&t comes up let go all three
Blue recovery
Select reinstall packages
Boots to same recovery
Reinstall packages
Green clockwork recovery
Rom should be saved to sd as well.
Select install zip from sd
Choose zip
Rom file
Confirm
done, let it do it's thing
enjoy
mcord11758 said:
No need to root when in stock.
Dl this
http://forum.xda-developers.com/attachment.php?attachmentid=464425&d=1292362952
This update zip gives you clockwork recovery.
When on stock put this on the root of your sd.
Phone off
Three button combo
When at&t comes up let go all three
Blue recovery
Select reinstall packages
Boots to same recovery
Reinstall packages
Green clockwork recovery
Rom should be saved to sd as well.
Select install zip from sd
Choose zip
Rom file
Confirm
done, let it do it's thing
enjoy
Click to expand...
Click to collapse
WOW! I clicked on the xda link from my phone and the update.zip got downloaded into the download folder in my internal sd (i deleted it). I see the point now. I need to root only to back up all apps and system data such as contacts, sms,media etc. Otherwise, no need to root. Please conform the steps one last time if you don't mind:
1. Copy the update.zip into the root directory of my phone (how to get to the root directory, by the way! Sorry it is a dumb question). Also, copy the custom ROM zip file to the same root directory.
2. Using 3 button combo, follow the remaining steps.
Now, after I successfully flash the custom ROM, can I use the android market and install all the apps I use.
Sent from my SAMSUNG-SGH-I897 using XDA App
antonyvijai said:
WOW! I clicked on the xda link from my phone and the update.zip got downloaded into the download folder in my internal sd (i deleted it). I see the point now. I need to root only to back up all apps and system data such as contacts, sms,media etc. Otherwise, no need to root. Please conform the steps one last time if you don't mind:
1. Copy the update.zip into the root directory of my phone (how to get to the root directory, by the way! Sorry it is a dumb question). Also, copy the custom ROM zip file to the same root directory.
2. Using 3 button combo, follow the remaining steps.
Now, after I successfully flash the custom ROM, can I use the android market and install all the apps I use.
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
When you open my files app you are looking at the root of your sd. You will see your download folder, go to it long press either file select move phone will direct you to root if sd, select paste.
You are correct you need root to run programs like titanium backup to backup your apps, but when you flash stock they will all be gone either way. So unless you are rooted now you can not back up your apps. You can dl them again do not restore any system data just user apps. Backup contacts by exporting to ext sd, or sim
I am checking out so I won't be responding again for the night. Good luck
The simplest way there is to root/ flash a rom is to use a one click root program.
http://forum.xda-developers.com/showthread.php?t=739304
If you use this, it roots your phone for you. After you root with the program in the link above( there are videos on how to use the program if you get confused ) Download Rom Manager from the market. open up rom manager and select flash clockwork mod recovery. After that in the program rom manager click reboot into recovery( easier than holding volume buttons) the stock recovery will pop up when the phone reboots. Click reinstall packages. It will bring you back to the stock recovery, click reinstall packages for a second time and you will have cwm (clock work mod ) recovery. In clockwork mod recovery there is an option to back up your phone. do this before you flash a rom. after you back up turn your phone on. Make sure it is in usb debugging. connect to your computer and on your phone select mount sd. drag the downloaded rom .zip file into the sd. the root of you phone is just what ever drive your phone shows up as. unplug your phone reboot into recovery and in cwm recovery there is an option to factory wipe, do this and after it is done, click the option install zip. then choose zip from sd. highlight the rom . zip file you are flashing and select it. it will take a minute or too and when it is done just reboot the phone. First boot will take a while but once it boots your all set. any questions you can pm me and good luck.
^ That's a way. .... OR you could use my program to do it all (Flash to stock, root, install custom ROM, etc.). Link is in my signature.
bay_wolf said:
^ That's a way. .... OR you could use my program to do it all (Flash to stock, root, install custom ROM, etc.). Link is in my signature.
Click to expand...
Click to collapse
also very true^^ his toolbox program has everything you would need in one spot
MaximumPotential said:
The simplest way there is to root/ flash a rom is to use a one click root program.
http://forum.xda-developers.com/showthread.php?t=739304
If you use this, it roots your phone for you. After you root with the program in the link above( there are videos on how to use the program if you get confused ) Download Rom Manager from the market. open up rom manager and select flash clockwork mod recovery. After that in the program rom manager click reboot into recovery( easier than holding volume buttons) the stock recovery will pop up when the phone reboots. Click reinstall packages. It will bring you back to the stock recovery, click reinstall packages for a second time and you will have cwm (clock work mod ) recovery. In clockwork mod recovery there is an option to back up your phone. do this before you flash a rom. after you back up turn your phone on. Make sure it is in usb debugging. connect to your computer and on your phone select mount sd. drag the downloaded rom .zip file into the sd. the root of you phone is just what ever drive your phone shows up as. unplug your phone reboot into recovery and in cwm recovery there is an option to factory wipe, do this and after it is done, click the option install zip. then choose zip from sd. highlight the rom . zip file you are flashing and select it. it will take a minute or too and when it is done just reboot the phone. First boot will take a while but once it boots your all set. any questions you can pm me and good luck.
Click to expand...
Click to collapse
Thanks a lot. This helps a lot. I also saw thw video on toolbox from bay_wolf on mobiletechvideo series. That looks pretty simple for an, amateur like me. The explanation you gave me is also superb. Thank you very much
Sent from my SAMSUNG-SGH-I897 using XDA App
bay_wolf said:
^ That's a way. .... OR you could use my program to do it all (Flash to stock, root, install custom ROM, etc.). Link is in my signature.
Click to expand...
Click to collapse
Thank you. I have your toolbox program installed in my computer running 64 bit windows 7 home.premium edition. I have a few questions. My phone is running the leaked JI6 2.2 rightnow. What should I choose first from the toolbox? If I choose, flash to stock then do I need to select thw JF6 firmware file from somewhere or the tool itself will do the job? Sameway, if I click root, then do I need to select a root / clockwork files to finish rooting or again the tool itself will do the job? I understand for flashing the custom ROM I need to choose the the ROM .zip file. I watched the video about your program on mobiletechvideos on youtube. I think I need to watch it again or if you don't mind then can you give me the steps to use your toolbox (given what firmware I have currently running). Thank you
Sent from my SAMSUNG-SGH-I897 using XDA App
Why ji6? What are the benefits other than the audience chip will work?

ROOT stock 1.47 ROM (hboot 6.98.1002) using 4EXTRecovery + Ad hoc wifi support

This tutorial is for noob people like me who needs a clean, simple and secure way to achieve something more from their stock ROM phones.
No doubt the devs are doing magics with their images but probably there are many conservative people who want to stay with their original firmwares.
So here we go:
My phone was runnig RUU_Saga_HTC_Europe_1.28.401.1_Radio_20.28b.30.080 5U_38.03.02.11_M_release out of the box first. It was S-ON. I S-OFFed it using Alpharevx and then I rooted it with Gingerbreak 1.20. Then I decided to update the phone with the stock RUU_Saga_HTC_Europe_1.47.401.4_Radio_20.28I.30.085 AU_3805.06.02.03_M_release_199410_signed and I lost my root but the phone was still showing S-OFF. Rooting with Gingerbreak is not working on 1.47.xxx ROMs. I rooted it using 4EXTRecovery v2.1.0 FINAL and this file from http://unrevoked.com/rootwiki/doku.php/public/revolutionary
To install 4EXTRecovery v2.1.0 FINAL on a non rooted phone(thanks to madmaxx82 and .sh4d0w.):
1. Download and unzip on your PC the attached 4EXTRecovery v2.1.0 FINAL.zip file
2.Copy all 5 files to the C:\ directory of your PC.
3.Connect your phone to the PC(debug usb option activated) charge only
4.Run cmd to open console, point to the directory where you copied the files and type: adb reboot bootloader - device will boot into the bootloader
5.Type: fastboot flash recovery recovery.img
Done
After reboot you should have 4EXTRecovery installed available from recovery option on your hboot menu.
6. Copy to the root of your SD Card the file su-2.3.6.3-efgh-signed.zip which you can download from here
7.Go to the 4EXTRecovery > install from sd card and choose su-2.3.6.3-efgh-signed.zip
8.Done. After reboot you should have SUPERUSER installed and your phone is rooted again
To get Ad hoc wifi support:
9.Download and unzip the attached Ad hoc.zip file to your PC.
10. Install from 4EXTRecovery ADHOC.v2.zip file and reboot.
11.Copy and replace wpa_supplicant file to: /system/bin
(you can use file expert apk from the market to do that)
Done. You have an Ad hoc wi-fi support.
YOUR PHONE MUST BE S-OFF BEFORE TO START THIS PROCEDURE!!!
DO IT ON YOUR OWN RISK!
Good luck!
You can have a look here for double check: http://forum.xda-developers.com/showpost.php?p=16171869&postcount=184
Just to be sure: does installing 4EXTRecovery or su-2.3.6.3-efgh-signed wipe any data from you phone?
NO it didn't !
I did it last night and worked !
Phone remains untached. Just rooted
Sent from my HTC Desire S using XDA Premium App
If I have ClockworkMod Recovery installed already then can I install 4EXTRecovery on top of that?
I don't think so. You better don't. But why do you need 4EXT once you have already CWM installed? I just shared one option to root 1.47.xx ROM which was not possible to do with Gingerbreak. If I have to remove CWM I would flash stock RUU. You will keep your S-OFF but will loose root. Then install 4EXTRecovery and proceed to root with the su-file. But maybe there is more elegant and time-saving way to do it. Just surch around the forum.
Sent from my HTC Desire S using XDA Premium App
Noob understands it to have better and more features.
This work with new hboot (6.98.1002 or like) or not
bilalovic1234 said:
This work with new hboot (6.98.1002 or like) or not
Click to expand...
Click to collapse
Yes, it works. That's the idea because Gingerbreak is not working on 6.98.1002
on cmd i have juste one message< waiting for device > how many time i need waiting or is wrong way
ando roido said:
If I have ClockworkMod Recovery installed already then can I install 4EXTRecovery on top of that?
Click to expand...
Click to collapse
yes you can install 4EXTRecovery on top of CWMR
4EXTRecovery basically is CWMR with more options & features
bilalovic1234 said:
on cmd i have juste one message< waiting for device > how many time i need waiting or is wrong way
Click to expand...
Click to collapse
Uninstall all HTC drivers and HTC Sync from your PC. Download fastboot drivers available here and install them. Make sure your phone is with USB debug active, connect it to the PC(charge only) and you should be OK. After everything done you may install your HTC Sync again if you want.
not help is same probleme .... f..ck.... i have superuser installed beefore this hboot and i cant delete superuser
bilalovic1234 said:
not help is same probleme .... f..ck.... i have superuser installed beefore this hboot and i cant delete superuser
Click to expand...
Click to collapse
Download the stock ROM from the dev section and flash the phone. I pointed this on the previous page. And follow the procedure - read it again.
teddy_irish said:
Download the stock ROM from the dev section and flash the phone. I pointed this on the previous page. And follow the procedure - read it again.
Click to expand...
Click to collapse
Same waiting for device all is ok but not work...
bilalovic1234 said:
Same waiting for device all is ok but not work...
Click to expand...
Click to collapse
But you have SuperUser installed so your phone is already rooted. What actually are you trying to do?
When I was installing the stock ROM I was using the drivers provided from the official HTC website. Before to succeed with flashing the RUU it gave me couple of times connection error and waiting for device. I tried with sync option and with charge option and it worked at the end. You can try that too. As far as I remember flashing the RUU was with USB debug OFF.
i have root my phone..
but i have problem with wifi..
i think i cant move the wpa_supplicant..
i have tick the root explorer in the file expert
any suggestion?
thanks u
loukasz said:
i have root my phone..
but i have problem with wifi..
i think i cant move the wpa_supplicant..
i have tick the root explorer in the file expert
any suggestion?
thanks u
Click to expand...
Click to collapse
What is the problem with your wifi? Install the file expert apk from market. Open it and go to the place on your SD Card where you put the file wpa_supplicant. Copy the file and navigate to /system/bin and paste it - it will ask you to overwrite the existing file. Press ok and that's it. Make sure that you have installed the ADHOC.v2.zip file from recovery too.
teddy_irish said:
What is the problem with your wifi? Install the file expert apk from market. Open it and go to the place on your SD Card where you put the file wpa_supplicant. Copy the file and navigate to /system/bin and paste it - it will ask you to overwrite the existing file. Press ok and that's it. Make sure that you have installed the ADHOC.v2.zip file from recovery too.
Click to expand...
Click to collapse
in wifi write error..
i replace the wpa_supplicant..any suggestion..i need my wifi
how can i check if the ADHOC.v2.zip installed?
edit:
Installing update...
Installing Wifi Adhoc..
Installation complete!
Install from sdcard complete
Click to expand...
Click to collapse
install again the ADHOC.v2.zip
replace the wpa_supplicant but Error in wifi still exist..
loukasz said:
in wifi write error..
i replace the wpa_supplicant..any suggestion..i need my wifi
how can i check if the ADHOC.v2.zip installed?
Click to expand...
Click to collapse
Just boot in to recovery and choose install zip from sd card
Navigate to ADHOC.v2.zip(the file should be on the root of your SD Card) and install it. Reboot.

S-off but no root?

Help, I attempted to root my Sensation. It says s-off but I'm not rooted, please help me. I used Revolutionary if that helps
Sent from my HTC Sensation 4G using XDA App
Make sure you have recovery installed clockwork.hen you need to flash the SU-sign.zip in threadnd you will have soft
Thanks, will do but I thought I did that when I was using Revolutionary. I'll do it again though, once again thank you
Sent from my HTC Sensation 4G using XDA App
follow this guide and you should be able to root your phone in no time
http://forum.xda-developers.com/showthread.php?t=1192300
Snake_skw said:
follow this guide and you should be able to root your phone in no time
http://forum.xda-developers.com/showthread.php?t=1192300
Click to expand...
Click to collapse
Thanks again, I'm not sleeping until I'm done lol kudos
Sent from my HTC Sensation 4G using XDA App
Hey snake when I get on to ROM manager an error occurred when trying to run privileged commands.
Sent from my HTC Sensation 4G using XDA App
When u root the sensation what you are doing first is s-off(ing) the bootloader. Then it boots u into revolutionarys recovery. From there u flash your su.zip. reboot. Rom manager. Flash clockwork mod and ur good to go.
sent from my Sensation
If you used revos method.
sent from my Sensation
royaljama said:
Hey snake when I get on to ROM manager an error occurred when trying to run privileged commands.
Sent from my HTC Sensation 4G using XDA App
Click to expand...
Click to collapse
thats because you dont have root and you have to flash the su-2.3.6.3-ef-signed.zip in the recovery to gain root access...
follow this simple guide:
1. Download the file su-2.3.6.3-ef-signed.zip from here: http://forum.xda-developers.com/attachment.php?attachmentid=670828&d=1311991644
2. Copy su-2.3.6.3-ef-signed.zip to your SD card root folder (main folder of your memory card)
3. Start clockworkmod recovery (instructions below. See To Start Clockwork recovery)
4. BACKUP YOUR ROM USING CWM BEFORE ATTEMPTING ROOT!
5. Navigate to "Backup & Restore" using the Volume Down button and press select (power button to select) then select "Backup"
6. Select "install zip from sdcard" after backing up
7. Then select "Choose zip from sdcard"
8. Then select "su-2.3.6.3-efgh-signed.zip"
9. Then select "Yes - install su-2.3.6.3-efgh-signed.zip" to confirm
10. Then go back
11. Then reboot.
12. You're rooted!
I've got s off and successful backup bus still no root...
I've followed the steps above to a "T" over and over with the same result. Every time I download this zip file and save it to the root of my phone's sd card. Then I open clockworkmod recovery mode on the phone, try to install the zip and all I get are when I open the SU-2 folder is more subfolders which clockworkmod tells me are empty. I've been working on this for days and can't figure out what I'm doing wrong to still not be rooted. What am I missing?
I say just follow the steps
revolutionary
superCID 11111111
PD58IMG of CWM to root of sdcard
bootloader(voldown + )
cwm installed
reboot
remove pd58 file
fastboot uncheck
poweroff
vol down+pwr
pick recovery
cwm
backup
flash custom rom that already has root
my two cents. this way was easier for me.
Great! It sounds like this will be helpful. Please forgive that i am a noob and I'm not familiar with the steps you just described.
1st. What is supercid 11111111?
2nd. It sounds like these steps are for installing CWM and creating a backup, which I have already done.
3rd. So you are saying that at this stage I can simply look for a custom rom that has root built in and flash it as is?
I appreciate the help and would benefit from any further explanation.
Thank you
ok so I've tried to install a custo rom - the latest leedroid- to see if it would work and I'm running into the same problem. I download the zip file, and then save the downloaded folder onto the root of my sd card. But whenever I go to install zip from sd card and select the file, all I get is subfolders. Where is the file I need to install for the custom rom? Am I doing something wrong? Is this because I'm using a mac?
My sd card is formatted properly, usb debugging is active, CWM seems to be working well enough, I don't get it.

Can't root my Sensation- Please Help!

I have an HTC sensation z7z10a. I purchased this phone to be able to get on AT&T's 3&4g frequencies without having to upgrade my unlimited data plan for non smart phones. So far so good, my phone gets 4g and AT$T is not aware that I have a smartphone.
Naturally after spending enough time in XDA and other phone forums to figure this out I became interested in flashing a custom ROM.
I used the revolutionary method to gain S-OFF, installed CWM, and used CWM to create a backup image. I've managed to fully wipe and then restore to my backup image, so CWM is working.
My problem is whenever I go to flash a custom rom I don't understand which file to select in recovery mode. Every zip I have downloaded, (including the one I need to finally get my phone rooted) opens up to a series of subfolders, none of which contain the files I need. The sub folders are typically : System, Data and META-INF. So I can't get rooted without being able to use the recovery mode to flash.
I used my friend's pc netbook in order to run Revolutionary and install CWM. Now I am using my Macbook Pro to download potential Roms zip files and move them onto my phones SD card. Could this be the problem?
I"ve searched and searched for and answer to this issue to no avail, please help me to figure this out. I'm stumped.
The zip you have to flash is the ROM you download...am I missing something?
You do not need to extract the zip file. Just put it on the SD card and then go to the recovery mode and select the option install zip from sd card and install it. I believe if you flash a custom rom, you would be automatically rooted, so no need to root it separately. Hope this helped
aNYthing24 said:
The zip you have to flash is the ROM you download...am I missing something?
Click to expand...
Click to collapse
Exactly- I don't understand why it won't work.
SickL1408 said:
You do not need to extract the zip file. Just put it on the SD card and then go to the recovery mode and select the option install zip from sd card and install it. I believe if you flash a custom rom, you would be automatically rooted, so no need to root it separately. Hope this helped
Click to expand...
Click to collapse
Thanks for this advice, this is my first time attempting this. I think you are right that most roms come with root access so I may be able to skip that step.
I know what you are saying, don't extract the file, just move the zip over as is. Only on my mac the files are arriving as a folder with subfolders, not a zip package. This HAS to be the problem! I will look harder for Mac info on downloaded zips to see if I can figure out why this is happening. Thanks again.
Update:
So I fixed the folder problem by going into safari settings and unchecking the open safe downloads box. No all the zip files I'm downloading are staying intact as zips.
However I just tried to flash revolution hd with no success. The full wipe zip for this rom was a failure as well. I will now try downloading the root zip again and see if rooting first helps at all.
So now I am rooted. Success!
imru88 said:
Update:
So I fixed the folder problem by going into safari settings and unchecking the open safe downloads box. No all the zip files I'm downloading are staying intact as zips.
However I just tried to flash revolution hd with no success. The full wipe zip for this rom was a failure as well. I will now try downloading the root zip again and see if rooting first helps at all.
Click to expand...
Click to collapse
Ah....Steve Jobs and his desire to prevent the user from doing anything useful strikes from beyond the grave.
This is why I won't touch a Mac. They want to do everything for you, even if it's not what you want or need to be done. On the plus side, at least you only have to push 1 button to get the Mac to do the wrong thing!
Glad you figured it out! Be careful with the ROM flashing though. It quickly becomes a life consuming obsession.

Need help fixing my phone

I just recently got an HTC One X and attempted to install a custom ROM on it. I have Cyanogenmod 10 on the phone but it is stuck in a bootloop and I forgot to make a recovery file of the stock ROM I had on here. I have seen people talk about installing a boot.img file but I have no clue a) where to find the file and b) how to install it. If someone could give me step by step directions on how to fix this I would be extremely appreciative. I also attempted to install the ruu file from a suggestion from someone else on here and it failed to update my phone and I attempted this twice. Any assistance would be of great help.
Try turning off your phone and rebooting into twrp recovery, connect your phone to a pc and mount storage. Download another Rom & move to phone , unmount,
System reset, wipe cache & davlik cache
Install other Rom reboot and wait patiently
Hopefully that'll work for ya. I would recommend viper 2.4.1
Sent from my HTC One X using xda premium
Thanks hopefully that works. I have rooted my phones a million times this is my first HTC phone and it has been such a pain! I'll try to other ROM you mentioned hopefully it will work for me. I read somewhere I need to change a boot.img file is that not true? If I do need to do that how will I go about doing so?
That worked! Thank you so much! Should I be able to flash other roms now or will that happen again?
Depends on your hboot version?
If your on hboot 1.14 you'll have to take these steps. All I did was copy this, as I've wrote this probably 100 times now:
Now this is using windows vista/7, hope you have it lol..
1. Download adb/fastboot from the first post in this thread. http://forum.xda-developers.com/showthread.php?p=28340689 now extract it.
2. Download the Rom of choice on either phone or computer. You'll need to copy it so that you have 2 copies, one for phone and one for computer. (This is the least confusing way).
3.download gapps onto your phone.
4. Right click and Extract the Rom.zip file... You'll see some files, the ONLY one you need is "boot.img" take the boot.img, copy it and paste it INSIDE THE ADB/FASTBOOT FOLDER.
5. Now enter recovery on phone. Choose "wipe".. wipe cache, dalvick, factory reset, system.. now go back and choose "install" Flash the Rom.zip followed by gapps.
6. Do not choose reboot! Instead, press back and choose reboot from the MAIN menu. One of the options is reboot to bootloader. Once in bootloader (white screen with skating androids) choose "fastboot"
7. On your computer, RIGHT CLICK your adb/fastboot folder. choose "open command prompt here"
8. Type --> fastboot flash boot boot.img
Success! Reboot phone and enjoy. it May seem like alot but I broke it down in individual steps. Others will argue to fastboot first or last, Ive seen my cousin have trouble doing it first. Now he does it last and its a success every single time. Feel free to ask any questions of you don't understand
9. Delete the extracted Rom contents to clean up and so you don't get confused if you have to do it to a different rom
Also check out the stickies in general section and development section. Guyincognito and redpoint has written some great tutorials and aquired a lot of resources rolled in to one. It would definatley benefit you to read up on it
Sent from my HTC One XL using Tapatalk 2

Categories

Resources