Odin 1.85 I get yellow on COM9.
I was trying KG4 and it failed.
I now get this trying KG4...
<ID:0/009> Removed!!
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_T959VUVKG4_CL385158_REV00_user_low_noship.tar.md5 is valid.
<OSM> T959VUVKG4-Phone-CL1037720.tar.md5 is valid.
<OSM> SGH-T959V-CSC-TMB-VIBRANTP.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009>
<ID:0/009> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
SOOOOOOO..... I searched and someone said do KC1 since it's asimple 1 file flash.....
I click PDA and select the KC1 file. I click start and it runs for a few minutes.
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_KC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> zImage
<ID:0/009> NAND Write Start!!
<ID:0/009> param.lfs
<ID:0/009> factoryfs.rfs
<ID:0/009> cache.rfs
<ID:0/009> data.rfs
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then I get FAIL.
If I reboot I get the TMobile Galaxy S screen stuck.
It's a new AT&T.
Help and thanks in advance. 3 hours of searching and flashing and still no go.....
hammermedia said:
Odin 1.85 I get yellow on COM9.
I was trying KG4 and it failed.
I now get this trying KG4...
<ID:0/009> Removed!!
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_T959VUVKG4_CL385158_REV00_user_low_noship.tar.md5 is valid.
<OSM> T959VUVKG4-Phone-CL1037720.tar.md5 is valid.
<OSM> SGH-T959V-CSC-TMB-VIBRANTP.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009>
<ID:0/009> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
SOOOOOOO..... I searched and someone said do KC1 since it's asimple 1 file flash.....
I click PDA and select the KC1 file. I click start and it runs for a few minutes.
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_KC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> zImage
<ID:0/009> NAND Write Start!!
<ID:0/009> param.lfs
<ID:0/009> factoryfs.rfs
<ID:0/009> cache.rfs
<ID:0/009> data.rfs
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then I get FAIL.
If I reboot I get the TMobile Galaxy S screen stuck.
It's a new AT&T.
Help and thanks in advance. 3 hours of searching and flashing and still no go.....
Click to expand...
Click to collapse
wait what phone do you have?
AT&T Branded Infuse 4G
:FACEPALM!!!!!!!: Let me tell you what section you are in.
Samsung Galaxy S 4G
Galaxy S 4G Q&A
Congrats. You have a paperweight. You need to find the Infuse 4G STOCK ROM better to check that devices forum.
No comment
Wow.
Sent from my SGH-T959V using XDA Premium App
and this is why i asked lol cause i read it just wanted to make sure that what i read was right lol thanks krylon and honk so i wasnt the only one that saw that
I've been flashing ROMs on phones for 6 years and this is a first.
The reseller I bought this thing from said it would take the Galaxy S ROMs. He will be getting a call tomorrow.
The Infuse forum had a ROM and I'm already back running.
hammermedia said:
I've been flashing ROMs on phones for 6 years and this is a first.
The reseller I bought this thing from said it would take the Galaxy S ROMs. He will be getting a call tomorrow.
The Infuse forum had a ROM and I'm already back running.
Click to expand...
Click to collapse
it does take galaxy s roms so long as there made for your device nottttttttttt another device
lmfao!!!!!! epic fail, you've been trolled
I like how krylon360 was the first to facepalm, haha. :x
Good to know your phone is running again though. Next time, be sure to use the proper ROMs, or else you'll just get a really fancy paperweight.
In addition to that, make sure you do research before you believe anything a reseller says. They'll sometimes say anything to sell you.
This is what happens every time:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_UCKD5.tar.md5 is valid.
<OSM> PHONE_UCKD5.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.rfs
<ID:0/003> dbdata.rfs
<ID:0/003> cache.rfs
<ID:0/003> param.lfs
<ID:0/003> zImage
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have tried 3 different computers with antivirus off and no other programs running and every usb port on those computers with 3 different cables each using [ODIN][UCKD5] GTG's Ultimate Unbrick following every step exactly. also tried using [ODIN][UCKD5] Odin - Stock (100% or Root+3e). ive been working on this for about 3 days and i able to get into download mode every time just fine no matter what state the phone is in and every computer recognizes the phone. no matter what it fails with the same error above.
Darthstygeon said:
This is what happens every time:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_UCKD5.tar.md5 is valid.
<OSM> PHONE_UCKD5.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.rfs
<ID:0/003> dbdata.rfs
<ID:0/003> cache.rfs
<ID:0/003> param.lfs
<ID:0/003> zImage
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have tried 3 different computers with antivirus off and no other programs running and every usb port on those computers with 3 different cables each using [ODIN][UCKD5] GTG's Ultimate Unbrick following every step exactly. also tried using [ODIN][UCKD5] Odin - Stock (100% or Root+3e). ive been working on this for about 3 days and i able to get into download mode every time just fine no matter what state the phone is in and every computer recognizes the phone. no matter what it fails with the same error above.
Click to expand...
Click to collapse
run Odin as an administrator. you may need to right click on the icon to get that option.
mfpearson said:
run Odin as an administrator. you may need to right click on the icon to get that option.
Click to expand...
Click to collapse
i forgot to mention that in my original post...i ran everything as administration with no different results. thanks though.
mfpearson said:
run Odin as an administrator. you may need to right click on the icon to get that option.
Click to expand...
Click to collapse
Have you tried to run Odin with no sd card in the phone?
no sd card no sim card or anything,,,,just the phone
I have got stuck in a boot loop, i forgot to make a backup in PhilZ Touch Advanced CWM Recovery and i've tried to restore to the original file with Odin3 V. 3.09 and
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T310UEUAMH2_T310XARAMH2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
this pops up. I have done the download mode and http://forum.xda-developers.com/showthread.php?t=2618798 tried using this tool so i could go to the stock firmware so far nothing is working. PLEASE HELP
Q&A for [ODIN][UCLB3] UCLB3 Unbrick - Return to stock - Working PIT included
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for [ODIN][UCLB3] UCLB3 Unbrick - Return to stock - Working PIT included. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
Attempted to follow the guide here on my old Infuse to breathe some life back into it, but I can't get it to work. Installed the drivers through Kies, Odin detects my phone in yellow. I follow the guide to the letter, but after flashing 'reset' in blue and getting the green 'pass' my phone simply doesn't reboot, nor can I boot it manually. I've removed the battery a few times and it doesn't change the situation. I can still boot into download mode with no issue and have tried flashing a few times, but I'm having no success booting the phone after Odin is done, nor can I get into recovery mode.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PHONE_UCLB3.tar.md5 is valid.
<OSM> PHONE_UCLB3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> modem.bin
<ID:0/003> modem.bin
<ID:0/003> Removed!!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Any ideas?
SG2Tiger said:
Attempted to follow the guide here on my old Infuse to breathe some life back into it, but I can't get it to work. Installed the drivers through Kies, Odin detects my phone in yellow. I follow the guide to the letter, but after flashing 'reset' in blue and getting the green 'pass' my phone simply doesn't reboot, nor can I boot it manually. I've removed the battery a few times and it doesn't change the situation. I can still boot into download mode with no issue and have tried flashing a few times, but I'm having no success booting the phone after Odin is done, nor can I get into recovery mode.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PHONE_UCLB3.tar.md5 is valid.
<OSM> PHONE_UCLB3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> modem.bin
<ID:0/003> modem.bin
<ID:0/003> Removed!!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Any ideas?
Click to expand...
Click to collapse
I never tried this flash before, but I do have a couple questions before proceeding...
Is your phone AT&T or Rogers?
Are you able to get back into download mode (that is, by method of device fully turned off, holding down both Volume Buttons and inserting the USB cable)?
joel.maxuel said:
I never tried this flash before, but I do have a couple questions before proceeding...
Is your phone AT&T or Rogers?
Are you able to get back into download mode (that is, by method of device fully turned off, holding down both Volume Buttons and inserting the USB cable)?
Click to expand...
Click to collapse
AT&T, the model is I997. I can still get into download mode, but I can't boot normally, nor into recovery mode (by holding volume up + volume down + power button; Samsung logo never appears). I used the included version of Odin with both the UCLB3_Unbrick_1.1.zip and UCLB3_Unbrick_root_1.1.zip files on the linked thread (I tried both).
SG2Tiger said:
AT&T, the model is I997. I can still get into download mode, but I can't boot normally, nor into recovery mode (by holding volume up + volume down + power button; Samsung logo never appears). I used the included version of Odin with both the UCLB3_Unbrick_1.1.zip and UCLB3_Unbrick_root_1.1.zip files on the linked thread (I tried both).
Click to expand...
Click to collapse
I always recommend this one for AT&T (could never try it myself, as I was a Rogers user), but you may have more luck with this (option A or D).
http://forum.xda-developers.com/showthread.php?t=1613523
joel.maxuel said:
I always recommend this one for AT&T (could never try it myself, as I was a Rogers user), but you may have more luck with this (option A or D).
http://forum.xda-developers.com/showthread.php?t=1613523
Click to expand...
Click to collapse
Tried this a few times and it keeps failing. It'll get about 1/3 of the way there and then my computer will make the 'device disconnected' noise and Odin will fail. I left it in download mode, plugged in, without attempting the download to see if it was an issue with my cable or port, and it didn't disconnect...it seems to only be happening when I attempt to flash the md5.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I997UCLB3-CWM-root-deodex-extras.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
SG2Tiger said:
Tried this a few times and it keeps failing. It'll get about 1/3 of the way there and then my computer will make the 'device disconnected' noise and Odin will fail. I left it in download mode, plugged in, without attempting the download to see if it was an issue with my cable or port, and it didn't disconnect...it seems to only be happening when I attempt to flash the md5.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I997UCLB3-CWM-root-deodex-extras.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
Even with option D? I see C was used, based on the log...
Sent from my Asus MeMO Pad 8"
joel.maxuel said:
Even with option D? I see C was used, based on the log...
Sent from my Asus MeMO Pad 8"
Click to expand...
Click to collapse
For some reason option D is taking an unreasonable amount of time to download (it's been over an hour now), so I had initially skipped it and tried options A and C, with the same results. I'll report back once I am actually able to get option D downloaded.
Same problem with every option. Progress reaches about halfway, then fails.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I997UCLB3-CWM-root-deodex.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
SG2Tiger said:
Same problem with every option. Progress reaches about halfway, then fails.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I997UCLB3-CWM-root-deodex.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
Last thing I can think of, you are using the Odin that comes with the package right?
joel.maxuel said:
Last thing I can think of, you are using the Odin that comes with the package right?
Click to expand...
Click to collapse
Yes, it should be Odin3 v1.7.
The dev-host file mirrors are down? Does anybody have copies of them to upload?
I need the one with root.
Umaroth said:
The dev-host file mirrors are down? Does anybody have copies of them to upload?
I need the one with root.
Click to expand...
Click to collapse
Sorry, no option A here, but I do have option C (with CWM, deodex, etc) on mirror. See the following link:
http://forum.xda-developers.com/showpost.php?p=58392432
Hope this helps.
Link Are Broken
Umm the link cant be downloaded.. i m trying to restore my infuse but most of the downloadable file is broken or file not found
ZExNos said:
Umm the link cant be downloaded.. i m trying to restore my infuse but most of the downloadable file is broken or file not found
Click to expand...
Click to collapse
Good evening,
Try my mirror:
http://forum.xda-developers.com/showpost.php?p=58392432
Options are limited, only "Option C" but it should be enough to get the job done.
Cheers.
Hey, I'm trying to return to stock firmware but all I can do is enter recovery or download mode. I tried to download odin 3.11 and previous user used and flash latest stock firmware from sammobile but all I get in odin is fails.
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
I'm flashing all 4 files CP,BL,AP,CSC
Sometimes I also get error FUSE 1 Binary or PIT
Any clues?
EDIT: WORKS!!! 3.11v of ODIN + SAMMOBILE latest Firmware. + restart of PC