Database Info

[ROM] Custom Roms For the GoGear Connect 3 8Gb

as I have promised here is are the first 3 custom ROMs for the gogear connect 3 8gb. if there is interest i will work on a few ROMs for the 16gb version also.
The way of installing roms on this device is a little different than most people are used to so i have included instructions
(with pictures this time!) but because of this way to do it it also makes this device almost brick proof and easy to fix.
before we start make sure your battery is at least charged 50%
THIS WILL DELETE ALL OF YOUR DATA EVEN THE STUFF ON THE "SD CARD"
In this guide i will be using the AndroidGeneric Rom for the example.
be sure to look in the rom package to see if i have given any extra instructions for the specific rom
1. Download the MfgTool Package at the bottom of this post. also download the rom package you wish to install.
2. extract the MfgTool Package somewhere onto your computer
3. extract the rom Package somewhere on your computer also.
4. now take the actual rom folder (in this case the AndroidGeneric folder) and put it into the profiles folder in MFG tool folder
5. Turn off your MP3 Player Compleatly
6. now with your player still turned off hold Volume Up and plug it into your computer.
7. dont let go of Volume Up untill a new device named SE Blank ELVIS shows up on your computer
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
8. install the driver located in the Drivers folder inside the MfgTools Folder (the driver isnt signed so you have to click a popup allowing it to install, x64 users may need to turn off driver signing to get this to work)
9. After Thats Done open MfgTool.exe
10. once Mfg tool is open click on the Options drop down menu from the menu bar and click Configuration
11. in the window that pops up Select the USB Ports tab. then scroll down the menu untill you find "Freescale i.MX51 USB BulkIO Device" and put a check mark in the check box next to it. then select ok.
12. now your back to the Mfg tool main window. Check the Profile drop down menu to make sure it is on the rom you want. then hit start.
13. it will install the rom you selected. when you get to the part where it says "please connect device" and the stop button is red it is done installing. hit the stop button and unplug your mp3 player from the computer.
14. turn on your mp3 player with its new rom. it may take a little bit longer than usual to start up but thats only because its for the first time.
15. you are done unless there are more instructions with the rom.
for people that have already done this, here is a set of instructions to install differant roms
1. extract the rom Package somewhere on your computer.
2. now take the actual rom folder (in this case the AndroidGeneric folder) and put it into the profiles folder in MFG tool folder
3. Turn off your MP3 Player Compleatly
4. now with your player still turned off hold Volume Up and plug it into your computer using the same usb port that you used the first time
5. dont let go of Volume Up untill you hear the beep of the computer recognizing the device.
9. After Thats Done open MfgTool.exe
12.Check the Profile drop down menu to make sure it is on the rom you want. then hit start.
13. it will install the rom you selected. when you get to the part where it says "please connect device" and the stop button is red it is done installing. hit the stop button and unplug your mp3 player from the computer.
14. turn on your mp3 player with its new rom. it may take a little bit longer than usual to start up but thats only because its for the first time.
15. you are done unless there are more instructions with the rom.
Here Are the Files:
MfgTool
Download
Custom rom AndroidGeneric with root and all the gogear modifications removed and the regular android files installed.(regular android boot screen also) (radio app is from original rom)
Download
Original Rom with Root
Download
Original Rom With Root and all the bloatware removed
Download

Do I need to be rooted already to follow these steps or it doesn't matter?

you dont need to be rooted this can be used as an alternative to rooting

thanks for the guide im rooted running stock rom minus bloat that u uploaded

im working on a pretty cool ROM. ill release it when i get all the bugs out. it will be completely different from the roms i have posted so far. im working on a mix between the honeycomb blue accents and ipod touch styling with the page transitions form ICS.and custom fonts. im using the MUIUI Music app to give it a mor ipod touch feel. when im done testing the rom ill post it up here for you guys.

at this moment in time i am unable to continue in develpoment on the device i had to sell it because of some financial issues. i will post the rom i made as it stood the day i sold the device. it was a pretty good rom and it was pretty straight foward. i will post it online within the next few days

I have a 16GB version and would love to install a custom ROM on it. Please count me ad interested in getting a 16GB version. I am also running a 64bit Version of Windows, does your guide support this, or only 32bit systems?

thanks! this gogear is my first android device.. i am currently running your -bloat rom. i would like to create my own roms. i was wondering though how is it you create these rom?? is there a tutorial somewhere about this?

Thank you for creating these ROMS. Can you confirm what build they are based off of?
The latest build from Phillips is:
Android Version: 2.3.3
Kernel Version: 2.6.35.3-00054-g1e2e42c
Build Number: GGC3.01.06.10
I am guessing that your builds are based off of these, but would like to make sure before I flash something. (This is good info to have in the OP in some form.)

Have one coming
When I get mines on the 12th ogf february i may see if i can make roms

HGStone said:
thanks! this gogear is my first android device.. i am currently running your -bloat rom. i would like to create my own roms. i was wondering though how is it you create these rom?? is there a tutorial somewhere about this?
Click to expand...
Click to collapse
you need a linux computer and the android sdk to develope and the adb drivers installed.

After following this guide, my GGC became bricked
MfgTool would stop at "Formatting op6 partition" before showing me "Update error -65535-" and after unplugging/plugging back in it shows up as "Linux File-Stor Gadget" and I can't access it from Windows because it says "Please insert a disk into drive X:" (I changed the drive letter so I wouldn't get confused)
It turns on but doesn't get past the Philips logo. I tried repairing it with songbird but I always ends with an unexplained error.
I tried flashing it with mateo1212's OriginalRooted and AndroidGeneric roms as well as the original GGC3 rom found in C:/Program Files/Philips/Philips Songbird Resources/Firmware/SA3CNT/SA3CNT.zip (extracted the archive to MfgTool/Profiles and named it SA3CNT) and still no luck, ending in the same error mentioned above.
Can anyone help? Philips is already sending me a replacement (I played dumb with them) but if I could save this one it would be great...

Can anyone help me with this? I`m doing everything as the instructions say, but the MfgTool wont update the rom.
It starts working on the device, but gets stuck on error message (operation time out). After that it starts all over by itself.
One possible reason could be that the mfgtool version provided here was not working properly on my win7 (64bit). To solve this I downloaded another version of the program form the authors website.
The reason I had to change version was that the mfgtool crashed everytime I entered the "configuration" menu and the "usb ports" submenu.
All the help is much appreciated!

yep
superkidmax said:
After following this guide, my GGC became bricked
MfgTool would stop at "Formatting op6 partition" before showing me "Update error -65535-" and after unplugging/plugging back in it shows up as "Linux File-Stor Gadget" and I can't access it from Windows because it says "Please insert a disk into drive X:" (I changed the drive letter so I wouldn't get confused)
It turns on but doesn't get past the Philips logo. I tried repairing it with songbird but I always ends with an unexplained error.
I tried flashing it with mateo1212's OriginalRooted and AndroidGeneric roms as well as the original GGC3 rom found in C:/Program Files/Philips/Philips Songbird Resources/Firmware/SA3CNT/SA3CNT.zip (extracted the archive to MfgTool/Profiles and named it SA3CNT) and still no luck, ending in the same error mentioned above.
Can anyone help? Philips is already sending me a replacement (I played dumb with them) but if I could save this one it would be great...
Click to expand...
Click to collapse
same man

superkidmax said:
After following this guide, my GGC became bricked
MfgTool would stop at "Formatting op6 partition" before showing me "Update error -65535-" and after unplugging/plugging back in it shows up as "Linux File-Stor Gadget" and I can't access it from Windows because it says "Please insert a disk into drive X:" (I changed the drive letter so I wouldn't get confused)
It turns on but doesn't get past the Philips logo. I tried repairing it with songbird but I always ends with an unexplained error.
I tried flashing it with mateo1212's OriginalRooted and AndroidGeneric roms as well as the original GGC3 rom found in C:/Program Files/Philips/Philips Songbird Resources/Firmware/SA3CNT/SA3CNT.zip (extracted the archive to MfgTool/Profiles and named it SA3CNT) and still no luck, ending in the same error mentioned above.
Can anyone help? Philips is already sending me a replacement (I played dumb with them) but if I could save this one it would be great...
Click to expand...
Click to collapse
Hi,
I also want to change rom but after reading you, I'm afraid now.
Have you take a look to this thread: http://forum.xda-developers.com/showthread.php?t=1396085
It says on the first post that:
I Have Figured out how to unbrick and flash this device if you have Messed it up while having root privileges. this method can also be used to install custom roms once some are made. if people need the repair/flash method or wanna work on roms let me know in the comments and i will post the files and guides needed for it.
Click to expand...
Click to collapse
Good luck.

I am new to this forum and normally would not dream of rooting so I have printed the instructions and thoughly read them. I wish to use the Original ROM rooted and with bloatware removed. I understand the instructions except for step 8. How do I install the driver?
Anyone know why some people report failure and bricked devices? I would hate for this to go wrong!

Where is everyone?

GraySan said:
I am new to this forum and normally would not dream of rooting so I have printed the instructions and thoughly read them. I wish to use the Original ROM rooted and with bloatware removed. I understand the instructions except for step 8. How do I install the driver?
Anyone know why some people report failure and bricked devices? I would hate for this to go wrong!
Click to expand...
Click to collapse
Hi, just follow the guideline it will be ok, as to step 8, in the device manager you should right click the SE Blank ELVIS and manually install the driver, wait a moment it will successfully install the driver, after that you can follow next step.
By the way, I just flashed under Win7 64, everything went smoothly when just follow the guideline. Thank you mateo1212!

For people with bricks because of this
PPl don't be scared if you get bricked, i try at first and i got bricked, my device was in a loop and did not start, at the beginning just was showing a black screen then i tried to turn it on and it was in a loop.But i manage to recover it! This is what i did to recover it:
Download the mfgtool provided in this post.
Download the android files to flash provided also here
Put the device in flash mode or whatever is called the state when you power on the device with the volume up key pressed. ( for me this was specially hard since it was doing a loop, what i did was to push the reset button with a needle, then as soon as release the reset, push the power button and the volume up, and then connect the usb cable... create your own way to do it, just keep in mind you need to have your device booted in this kind of service mode ( vol up and power) before proceed.
Then just click on start and wait... it did it successfully this time...
Obviously you need to put your rom folder in profiles and everything just as explained in this guide.
THANKS, I UPDATED MY DEVICE WITH ROOT! :cyclops:
---------- Post added at 05:48 AM ---------- Previous post was at 05:41 AM ----------
GraySan said:
I am new to this forum and normally would not dream of rooting so I have printed the instructions and thoughly read them. I wish to use the Original ROM rooted and with bloatware removed. I understand the instructions except for step 8. How do I install the driver?
Anyone know why some people report failure and bricked devices? I would hate for this to go wrong!
Click to expand...
Click to collapse
In my case it failed just after it erase everything with no reason, however the same method worked the second time so i think is not risky to try, you are going to be able to install it eventually following this method. For more info see my other post. Cheers.

fail to root it by supper click try download flash
I try to use supper click to root it but failed the information is like below
step #7 WaitForDevice ................short name = mixed, utf8, errors = remount-ro)/dev/b.
any idea about it?

Driver issues mt65xx,solved (easy),mediatek devices(canvas a116)

1>TAKE THE BATTERY ,SD ,SIM OUT OF THE PHONE
2>HOLDING VOLUME+ CONNECT IT TO PC VIA USB(ONCE YOU HEAR A SOUND FROM PC YOU CAN RELEASE VOLUME+)
3>OPEN DEVICE MANAGER(ON COMPUTER SEARCH IT OR CONTROL PANEL)
4>WAIT FOR 2-3 MINUTES
5>YOU WILL HEAR A SOUND & OTHER DEVICE WILL BE DISPLAYED
6>IN OTHER DEVICES ->MT65XX PRE-LOADER
7>RIGHT CLICK MT65XX PRELOADER
8>UPDATE DRIVER
9>LOCATE THE DRIVERS PROVIDED ACCORDING TO YOUR OS(VISTA,WIN7,XP)
10>IT WILL DO ITS STUFF
11>YO MAN THATS IT KeEp fU**ING d-_-b
NOTE:-
now you can flash firmware through sp-flash tool
if it does'nt work for first time repeat again
it will work for 2 or 3rd time
HOPE THIS WAS HELPFULL:fingers-crossed::fingers-crossed::fingers-crossed:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
waNNa AppReCiate

bhargav1991 said:
1>TAKE THE BATTERY ,SD ,SIM OUT OF THE PHONE
2>HOLDING VOLUME+ CONNECT IT TO PC VIA USB(ONCE YOU HEAR A SOUND FROM PC YOU CAN RELEASE VOLUME+)
3>OPEN DEVICE MANAGER(ON COMPUTER SEARCH IT OR CONTROL PANEL)
4>WAIT FOR 2-3 MINUTES
5>YOU WILL HEAR A SOUND & OTHER DEVICE WILL BE DISPLAYED
6>IN OTHER DEVICES ->MT65XX PRE-LOADER
7>RIGHT CLICK MT65XX PRELOADER
8>UPDATE DRIVER
9>LOCATE THE DRIVERS PROVIDED ACCORDING TO YOUR OS(VISTA,WIN7,XP)
10>IT WILL DO ITS STUFF
11>YO MAN THATS IT KeEp fU**ING d-_-b
NOTE:-
now you can flash firmware through sp-flash tool
if it does'nt work for first time repeat again
it will work for 2 or 3rd time
HOPE THIS WAS HELPFULL:fingers-crossed::fingers-crossed::fingers-crossed:
Click to expand...
Click to collapse
Still showing the same error: "S_BROM_CMD_STARTCMD_FAIL (2005)". Please tell me what to do.
Another thing, when I connect my A25 phone without battery, the device manager list updates itself every two seconds: once it shows the preloader vcom port and then in the next refresh there's no vcom port and this process repeats. Any idea why?

Follow the same procedure with this drivers http://www.mediafire.com/?31nddwqdot5ajp2
Sent from my Micromax A110 using xda premium

bhargav1991 said:
1>TAKE THE BATTERY ,SD ,SIM OUT OF THE PHONE
2>HOLDING VOLUME+ CONNECT IT TO PC VIA USB(ONCE YOU HEAR A SOUND FROM PC YOU CAN RELEASE VOLUME+)
3>OPEN DEVICE MANAGER(ON COMPUTER SEARCH IT OR CONTROL PANEL)
4>WAIT FOR 2-3 MINUTES
5>YOU WILL HEAR A SOUND & OTHER DEVICE WILL BE DISPLAYED
6>IN OTHER DEVICES ->MT65XX PRE-LOADER
7>RIGHT CLICK MT65XX PRELOADER
8>UPDATE DRIVER
9>LOCATE THE DRIVERS PROVIDED ACCORDING TO YOUR OS(VISTA,WIN7,XP)
10>IT WILL DO ITS STUFF
11>YO MAN THATS IT KeEp fU**ING d-_-b
NOTE:-
now you can flash firmware through sp-flash tool
if it does'nt work for first time repeat again
it will work for 2 or 3rd time
HOPE THIS WAS HELPFULL:fingers-crossed::fingers-crossed::fingers-crossed:
Click to expand...
Click to collapse
Hi,
I am having trouble installing drivers for win 8 x64 for micromax a116, which has same chip.
I have tried all possible things... can't install... any help ??
thanks
greg

i have tried this method and it works 100% try with different ports it should work and make sure which version u have 32 bit(x86) or 64 bit(x64)

Anybody know how to get one of these phones to connect with the tmobile network?

Well all this mediatek devices are unlocked .so any carrier sim should work
Sent from my GN708W using xda premium

gregferns said:
Hi,
I am having trouble installing drivers for win 8 x64 for micromax a116, which has same chip.
I have tried all possible things... can't install... any help ??
thanks
greg
Click to expand...
Click to collapse
Follow the below approach to install the drivers on Windows 8:
1. Go to the right bottom corner of the desktop and wait for the side menu to appear. When it's there click on the gear icon with the title "Settings".
2. Now click on the entry "More PC Settings", then click on the entry "General".
4. Scroll down to "Restart now" (under "Advanced startup") and click it.
5. Wait a bit for a menu.
6. Now click "Troubleshoot", then "Advanced Options" and after that click "Windows Startup Settings".
7. Click on "Restart" and wait for the profit to happen.
When the computer restarts, select the option "Disable driver signature enforcement". After it finally booted into the operating system you can install the unsigned driver. After you've installed the driver reboot once again and you're done.

hafizimtiaz said:
Still showing the same error: "S_BROM_CMD_STARTCMD_FAIL (2005)". Please tell me what to do.
Another thing, when I connect my A25 phone without battery, the device manager list updates itself every two seconds: once it shows the preloader vcom port and then in the next refresh there's no vcom port and this process repeats. Any idea why?
Click to expand...
Click to collapse
It did the same thing with my MT6577 (Wiko Cink PEAX), so I connected it with a battery and without holding VOL+. Then "MT65xx preloader" appeared in device manager then disappeared (once). It is normal that it disappears. When you start Flash_tool and when you click Download (or whatever you want to do) THEN you connect the phone (in off state), and the flash operation will succeed.

n4w4k said:
It did the same thing with my MT6577 (Wiko Cink PEAX), so I connected it with a battery and without holding VOL+. Then "MT65xx preloader" appeared in device manager then disappeared (once). It is normal that it disappears. When you start Flash_tool and when you click Download (or whatever you want to do) THEN you connect the phone (in off state), and the flash operation will succeed.
Click to expand...
Click to collapse
worked for me also
first you have to install those above given drivers
and after that you able to:highfive::highfive::highfive::highfive:

Thank you so much!

When i connect device to pc via usb.. a sound comes and it shows in list of drivers as in other devices and within 2 seconds it removes from device manager with another sound.. i did try this many times but same result..
Wat to do?..
Sent from my A116 using xda premium

gregferns said:
Hi,
I am having trouble installing drivers for win 8 x64 for micromax a116, which has same chip.
I have tried all possible things... can't install... any help ??
thanks
greg
Click to expand...
Click to collapse
I m having same issue in windows 8..did u got any solution ?
---------- Post added at 10:08 AM ---------- Previous post was at 09:41 AM ----------
avi_wizard said:
Follow the below approach to install the drivers on Windows 8:
1. Go to the right bottom corner of the desktop and wait for the side menu to appear. When it's there click on the gear icon with the title "Settings".
2. Now click on the entry "More PC Settings", then click on the entry "General".
4. Scroll down to "Restart now" (under "Advanced startup") and click it.
5. Wait a bit for a menu.
6. Now click "Troubleshoot", then "Advanced Options" and after that click "Windows Startup Settings".
7. Click on "Restart" and wait for the profit to happen.
When the computer restarts, select the option "Disable driver signature enforcement". After it finally booted into the operating system you can install the unsigned driver. After you've installed the driver reboot once again and you're done.
Click to expand...
Click to collapse
great it worked for me :good:

guys help me i have gionee p2 mtk6572 but i cant install the drivers on windows 8 help me with the drivers or how to connect the device please....!!

How to flash without scatter file????????????

bhargav1991 said:
1>TAKE THE BATTERY ,SD ,SIM OUT OF THE PHONE
2>HOLDING VOLUME+ CONNECT IT TO PC VIA USB(ONCE YOU HEAR A SOUND FROM PC YOU CAN RELEASE VOLUME+)
3>OPEN DEVICE MANAGER(ON COMPUTER SEARCH IT OR CONTROL PANEL)
4>WAIT FOR 2-3 MINUTES
5>YOU WILL HEAR A SOUND & OTHER DEVICE WILL BE DISPLAYED
6>IN OTHER DEVICES ->MT65XX PRE-LOADER
7>RIGHT CLICK MT65XX PRELOADER
8>UPDATE DRIVER
9>LOCATE THE DRIVERS PROVIDED ACCORDING TO YOUR OS(VISTA,WIN7,XP)
10>IT WILL DO ITS STUFF
11>YO MAN THATS IT KeEp fU**ING d-_-b
NOTE:-
now you can flash firmware through sp-flash tool
if it does'nt work for first time repeat again
it will work for 2 or 3rd time
HOPE THIS WAS HELPFULL:fingers-crossed::fingers-crossed::fingers-crossed:
Click to expand...
Click to collapse
Thanks mate. It helps.

solved my problem with windows 7 installation using guide wrote below
hope it helps some one
MT65xx Driver
MT65xx Drivers guide
press thanks if it works

Well.
I've posted in other similar threads today but its because i really need help - running out of alternatives.
I've partially bricked my THL T200 - it is stuck in bootanimation after i removed gallery.apk from the rom using TitaniumBackup.
Already tried all those flash methods in different sequences (with battery, without battery) but my phone just connect\disconnect all the time - i can't even install the VCOM driver.
I've TWRP installed - is there any rom for this phone i can flash using this.
All i want is go back to stock.
Thanks in advance for any ideas !

abhishekjain.ims said:
I m having same issue in windows 8..did u got any solution ?
---------- Post added at 10:08 AM ---------- Previous post was at 09:41 AM ----------
great it worked for me :good:
Click to expand...
Click to collapse
Bro, how did you install it on win 8?? i have win 8.1 64 bit OS and whenever i try installing this following the same procedure, it says "The folder you specified does not contain a compatible software driver for your device." i' unable to install this darn driver.. please help

n4w4k said:
It did the same thing with my MT6577 (Wiko Cink PEAX), so I connected it with a battery and without holding VOL+. Then "MT65xx preloader" appeared in device manager then disappeared (once). It is normal that it disappears. When you start Flash_tool and when you click Download (or whatever you want to do) THEN you connect the phone (in off state), and the flash operation will succeed.
Click to expand...
Click to collapse
mayank88288 said:
worked for me also
first you have to install those above given drivers
and after that you able to:highfive::highfive::highfive::highfive:
Click to expand...
Click to collapse
I Cant install the given drivers if MT65xx preloader disapears..?
And when i connect in off mode to my laptop and flash tools on download mode it does nothing my phone just goes charging?
See this thread: http://forum.xda-developers.com/general/help/mt65xx-flashing-problem-sp-flash-tool-t2846054

[DISCUSSION][GUIDE][PORT][ROM] Alcatel One Touch 4030 S'Pop/Glory 2 Development

This thread is for discussion for the development of this device. All interested devs are very welcome to join and help.
I started working on this device since I got it day 1 on March 11, 2013. Slowly, I progressed to every step in learning more about this device. Since then, many have joined finding ways to make this device better.
UPDATE:
This thread is old and very few to none uses this device anymore. I will leave this thread here for your reference.
All of the developments of this device will still be posted here so always keep in touch with this thread for great news.
Cheers! :good:

Unbrick theory...
trying the one touch upgrade utility. it wipes all data in phone and installs a fresh and latest ROM for the device. i guess this will also fix a bricked device somehow.
after this i will try to root it again using MTK tools and ap flash tools with a different idea in my mind... hope it works this time...
[EDIT] UNBRICK METHOD CONFIRMED WORKING!!!

One touch Upgrade
Hello there I'm a total noob in rooting and unlocking bootloads. I just got the same phone as my first android phone and wondered how to root it and I end up here. Now I'm asking how did you get the one touch upgrade software. I've searched the whole alcatel website but I keep getting on the FAQ page. Would you be so kind to put up the link for the software because I kinda bricked my phone here. I was also wondering what speed did you use during your Bin4ry script root attempt? Normal or Special? Keep doing a good job. Thanks for having the time to look for ways to root this phone.

sabinbp said:
Hello there I'm a total noob in rooting and unlocking bootloads. I just got the same phone as my first android phone and wondered how to root it and I end up here. Now I'm asking how did you get the one touch upgrade software. I've searched the whole alcatel website but I keep getting on the FAQ page. Would you be so kind to put up the link for the software because I kinda bricked my phone here. I was also wondering what speed did you use during your Bin4ry script root attempt? Normal or Special? Keep doing a good job. Thanks for having the time to look for ways to root this phone.
Click to expand...
Click to collapse
I tried the normal mode as Bin4ry said that the others might brick the phone it it wasn't the right model. did you brick it using the srcipt? any way. still trying to root it and finding help from rua1 that has a great knowledge in MTK phones...
here's the link of the upgrade utiliuty... just install it and choose alcatel 4030 (if your phone is s'pop) then power of the phone remove the battery and follow the instructions on PC and wait till it says plug the phone while powered off.. plug the usb (without battery) then wait for it to detect the device. when it loads, put the battery back and wait for it to download the firmware.. it will take hours to download it.. it's about 2+gigs... good luck on unbricking.. hope it works...

Phone unbricked
Many thanks for the software. My phone is now back to stock rom. for the Bin4ry I also tried Normal because I thought it was for tabs only. So MTK is the only course of action? Any news on fixing the 2 point horizontal bug? and the alcatel FAQ says there's this TCL calibration that you can activate to you know "calibrate" the touch screen. Do you also get the problem where in the stock alarm app alarms but you can't dismiss it ( I set it to crazy mode ) where you need to press 3 buttons to dismiss but still won't stop I really need to pull the battery out. Help please Thanks in advance.

sabinbp said:
Many thanks for the software. My phone is now back to stock rom. for the Bin4ry I also tried Normal because I thought it was for tabs only. So MTK is the only course of action? Any news on fixing the 2 point horizontal bug? and the alcatel FAQ says there's this TCL calibration that you can activate to you know "calibrate" the touch screen. Do you also get the problem where in the stock alarm app alarms but you can't dismiss it ( I set it to crazy mode ) where you need to press 3 buttons to dismiss but still won't stop I really need to pull the battery out. Help please Thanks in advance.
Click to expand...
Click to collapse
Great. So my theory really worked. Glad you unbricked it. I'm getting closer to rooting it. Just having problems flashing the cwm. Ones I managed to flash it, rooting may be successful. I use Mtk tools and flash tools and get help from rua1. Didn't use my alarm before so i'm not sure about the bug. Maybe you don't have to set it in crazy mode..

I tried to set the alarm in crazy mode and everything works fine. Just dismiss, unlock, and tap the three buttons with numbers and your done..

Rooted, finally!!
I finally rooted the alcatel spop. I will make a guide maybe later how I did it...

[GUIDE]How to flash CWM recovery and root Alcatel One Touch S'POP 4030
How to flash CWM recovery and root Alcatel One Touch S'POP 4030X(Glory 2)
Disclaimer: Your warranty is now void. You do this in your own risk. I do not take any responsibility to your device. This will definitely brick your device which is normal but follow the right instructions to make it work again.
Credits: This is tuts would not be possible without the help from the creator of MTKdroid tools, rua1 from XDA Developers. Thank the guy for his wonderful tool. If you wanna know how I did it, go to his thread right here. I also wanna acknowledge The Solutor and rimmon1971's efforts for porting the TWRP to our device. You can find The Solutor's work here.
Requirements:
1. A windows based PC
2. MTK Droid Root & Tools & SP Flash Tool
3. Universal ADB driver
4. One Touch Upgrade S
5. Root script
6. Patience
7. Most important! Use your brain!
Important!
To make this work without errors, don't use other drivers available in the web. Just install One Touch Upgrade S first. It will install the USB VCOM preloader driver. It will be needed by the SPFT to detect the phone. Use the provided ADB driver for the MT65xx_android_phone. If ever you get stucked in an error and your device wont boot anymore, just use One Touch Upgrade and your phone will be as good as new...
Guide: CWM/TWRP recovery
1. Download MTK Droid Root & Tools & SP Flash Tools, ADB Drivers, One Touch Upgrade S, and the Root script. Extract them anywhere in your computer.
2.Install ADB driver.This step is now optional to get adb working. You can now skip to step 5 if you just want to get rooted with CWM/TWRP recovery installed.. In your phone, go to Settings>Development. Set to on and check USB debugging.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3. Connect device to PC. Driver will fail to install (thats normal). Install UniversalAdbDriverSetup6.msi
Note: in Windows 8, this will pop-up. do this:
4. After installing the Universal ADB driver, go to device manager of your computer. Follow the images as descirbed.
ADB commands should work now (if you have ADB installed) and you won't have any problems about MTK droid tool not detecting phone.
5. Be sure that you have already installed One Touch Upgrade S before this step. Open SP Flash tool and select the scatter file by clicking on the Scatter-loading button.
6. UNCHECK BOOT and leave RECOVERY checked. Disregard what is on the photo. There's are reports that the latest firmwares are incompatible with the uploaded patched boot.img.
Note: By default, the CWM recovery will be selected in the SP Flash tool. If you want the fully working TWRP-recovery (I recomment this because CWM recovery is not fully functional), just click RECOVERY and replace it with this file.
7. Click Download button. Click yes on the download warning. Turn off phone, remove battery and connect the phone (without battery) and wait until SP Flash tool detects the phone and watch as it flash the image.
8. If everything passes without errors, unplug the phone, reinsert battery and boot to recovery by pressing power + volume up.
9. You should boot in CWM/TWRP recovery. We are ready to flash the Superuser app to gain root.
Guide: Superuser
You can use mtk droid root and tools here. Just plug in phone to pc while still in CWM recovery. Run mtk tools, wait to detect phone, click superuser, then build.prop, then delete china. Your done. Or use the guide below if you have problems with it.
Using CWM recovery to flash superSU
1. While still on CWM recovery, plug the phone into PC again.
2. Navigate using volume up and down buttons. Press Power button to select and Back soft key to go back.
3. Select mounts and storage>mount USB storage.
4. Copy the root-glory-2-4030E.zip to your sdcard.
5. After copying, select unmount and go back.
6. Select install zip from sdcard>choose zip from sdcard>root-glory-2-4030E.zip and select yes - Install root-glory-2-4030E.zip
7. It will flash the app to the system including all needed binaries. I also included the fix-permissions banary which is missing from the ROM.
8. Reboot the phone and wait. It will boot normally and no data will be lost. You will see superuser app in your app drawer. You are now rooted!:thumbsup:
Using TWRP recovery to flash superSU
1. While still on TWRP recovery,Connect the device to PC.
2. Tap mount in the screen then Mount USB storage.
3. Copy the root-glory-2-4030E.zip to your sdcard.
4. Press back on your device softkeys.
5. Tap install and select root-glory-2-4030E.zip
6. Wipe to confirm flash.
7. Reboot>System.
8 You're done.
Screenshots:
Guide to Unroot
Requirements:
1. Windows Based PC
2. SP flash tool (included in OT-4030 ROOT&CWM RECOVERY)
3. Stock recovery.img
4. Unroot script (Unroot-glory-4030E.zip)
Urooting
1. Copy Unroot-glory-4030E.zip to the root of sdcard.
2. Reboot to CWM recovery.
3. Select install zip from sdcard>choose zip from sdcard>Unroot-glory-4030E.zip and select yes - Install Unroot-glory-4030E.zip
4. On your PC, Open SP flashtool and select the scatterfile.
5. Remove check on BOOTIMG and click RECOVERY and select the stock recovery.img. Click download button and disregard download warning by clicking yes.
6.Connect the phone to pc without battery. After the download finished dialog, your done!
Links:
OT-4030 ROOT&CWM RECOVERY
Universal ADB driver
One Touch Upgrade S
Root script
Unroot script
Stock recovery.img
Mirror to all files
TWRP-recovery

I get this error after #3 of CWM recovery installation:

warfab said:
I get this error after #3 of CWM recovery installation:
Click to expand...
Click to collapse
Please attach log...

cyberangel22k said:
Please attach log...
Click to expand...
Click to collapse
Here are my logs...

Guide updated!
added some more steps for error 4050...

Anyone still getting errors, I will help today. you can send a PM on my personal G+ so I can answer quickly to your concerns...

boot_logo changed!
tried to change the boot logo and it worked! thanks to balamu96m for his guide.
This is my new boot logo

bootanimation problem!
I changed my bootanimation and tried if it works using these commands which i normally do with my past android devices.
Code:
adb shell bootanimation
the animation works fine but when i hit:
Code:
adb reboot
the animation showed was just android mask or android shine which shows when you don't have bootanimation.zip inside /data/local or /system/media. it's like a default bootanimation.
so once I booted, I tried again
Code:
adb shell bootanimation
the bootanimation works but when I reboot, it's back to default.
I tried replacing back the original bootanimation.zip but it still the defaut bootanimation. It's very weird. I haven't encountered this before...

cyberangel22k said:
Anyone still getting errors, I will help today. you can send a PM on my personal G+ so I can answer quickly to your concerns...
Click to expand...
Click to collapse
Me and many others are still waiting for your help at symbianize...

can't access symbianize since saturday
Dito muna kayo magpost ng mga tanong.. humihingi din ako ng tulong kay rua1 re: sa error 4050.

fixed!
cyberangel22k said:
I changed my bootanimation and tried if it works using these commands which i normally do with my past android devices.
Code:
adb shell bootanimation
the animation works fine but when i hit:
Code:
adb reboot
the animation showed was just android mask or android shine which shows when you don't have bootanimation.zip inside /data/local or /system/media. it's like a default bootanimation.
so once I booted, I tried again
Code:
adb shell bootanimation
the bootanimation works but when I reboot, it's back to default.
I tried replacing back the original bootanimation.zip but it still the defaut bootanimation. It's very weird. I haven't encountered this before...
Click to expand...
Click to collapse
Found out the cause of this issue. The stock ROM has no fix_permissions binary. So I pushed the binary and tried to fix perm again and now custom bootanimation.zip works!

4050 fix
to get past the 4050 error update the SPFlash Tool to this one http://forum.xda-developers.com/showthread.php?t=1982576
To those having problems with MTKDroid not detecting their phone download and install PDANet for Windows (any version would suffice)
just rooted my phone \^0^/

The complete solution to repair dead boot and unbrick and update LG P920 O3D

The complete solution to repair dead boot and unbrick and update & root LG P920 O3D to Android 4.0.4 without any problems with the official Rom ICS{ all fix}full 3D and camera work perfect all the most languages support.
Before anything make sure that all LG Drivers and everything Installed and run under Windows 7 ultimate and disable user account control settings don't run under Windows 8
LG Drivers https://docs.google.com/file/d/0Bwirw62bfRfebUNQNjJzUHlNbHM/edit?usp=sharing
First, download the following files:
1- flash fastboot and Replace the original boot and download mode http://www.mediafire.com/download/b...for_optimus-v1.22+modified+by+XcachorroX®.rar
or
https://drive.google.com/file/d/0Bwirw62bfRfeY2hsY3JRTDIybTQ/edit?usp=sharing
2- download Rom https://drive.google.com/file/d/0Bwirw62bfRfeM0dXbUVpcmNUOEU/edit?usp=sharing
3- download SmartFlashTool-3D to flash rom by fls and bin file https://docs.google.com/file/d/0Bwirw62bfRfeY0hKNjlqZFRSdUU/edit?usp=sharing
Second
Instructions:
After downloading the files previous
1- flash fastboot and Replace the original boot and download mode Until the fastboot is the basic boot for device.
Connect phone without battery,phone detect OMAP4430 {device manager}
Install driver omap "inside folder have drivers"(omap4boot-for_optimus-v1.22 modified by XcachorroX®\usb_drv_windows) by select update driver then select browse my computer for driver {install driver Manual}View attachment 2067365
After driver installation ends remove usb cable
Run start_fastboot.bat and select option 2
Pull out battery
when is waiting for omap44 connect usb cable to your phone he start .
then insert battery to your phone when is waiting5 Seconds and follow the instructions on screen after this you see logo LG Gray
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
in phone and He asks you entered fastboot Answer no and accept to flash and Replace the x-loader and u-boot source then inter to download mood and flash .
If the LG COSMO appears in device manager install driver for her by select update driver then select browse my computer for driver {install driver Manual} and select Install driver from "inside folder have drivers"(omap4boot-for_optimus-v1.22 modified by XcachorroX®\usb_drv_windows) then try again step 2 flash fastboot .
Another method to flash fastboot {Flash Wkpark boot loader +cwm normal recovery } use this tool and and follow the instructions on the screen https://docs.google.com/file/d/0Bwirw62bfRfeUWw0QU5jRVV4UlU/edit?usp=sharing
A Small Guide if Anyone has troubles installing Omap4430 Driver in Windows 7
arsen4oo said:
When plugging the phone in,find OMAP4430 in "Other Devices" in Device Manager.
Right click on OMAP4430,then click "Update Driver Software..."
Then browse to your omap4boot 1.8 folder that you have extracted from zip
Choose the usb_drv_windows folder and click OK
While installing the driver,ignore any warning messages
After installation finished you will be able to ressurect your phone
Good Luck!
Click to expand...
Click to collapse
2-flash Rom:
Connect phone usb with pc and Enter in download modeView attachment 2067367
Enter in download mode : Pull out battery then Hold Vol+ then connect usb cable to your phone then insert battery to your phone with Hold Vol+ .
run SmartFlashTool-3D and select mode Rom copy D/L and in destination binary file select CP.fls file in CP bin and select AP.bin file in AP bin from extract rom folder Then press Start .
After flash rom If the screen appears encryption unsuccessful
Make hard reset for phone by turn off phone then press hold down volume and power button and Make hard reset for phone.then restart phone.
Root:
Follow this method http://forum.xda-developers.com/showthread.php?t=2366916
1. Download This Drives and Install Them Both
2. Download This Root and Than Extract The Zip and Install The Root Program
3-A. In Your Phone Go To Settings -- Security And Enable Unknown sources
3-B. In Your Phone Go To Settings -- Developer options And Enable USB debugging
4. Connect your Phone To PC using Cable and Than Open The Root Program and Wait until u see your Device Name.
5. Your Phone Well Auto Reboot after Complete
6. Done
Install CWM & TRWP recovery mood :
install this as normal application and run after root your phone
https://docs.google.com/file/d/0Bwirw62bfRfeb2JPbEhKTXQ2OEE/edit?usp=sharing
FM Radio:
https://docs.google.com/file/d/0Bwirw62bfRfeX1BMWGFvMDVzSEk/edit?usp=sharing
extract then put FM Radio for ics 4.0.4 Lgp920.zip in external sd card then flash it by inter cwm mood recovery then choose install from sdcard then choose zip from sdcard then choose FM Radio for ics 4.0.4 Lgp920.zip
that's all after root phone and install cwm mood recovery.
Thank you for all
have a nice time

Where is the difference of this one:
http://forum.xda-developers.com/showthread.php?t=2246001
Sent from my LG-P920 using xda app-developers app

Difference in that it is easier with ROM no one touched and stable
p-vlad said:
Where is the difference of this one:
http://forum.xda-developers.com/showthread.php?t=2246001
Sent from my LG-P920 using xda app-developers app
Click to expand...
Click to collapse
I tried many ways to update my phone but I have a problems in camera ... etc.
Until my phone died and I found a way to reach a stable rom without problems and succeeded
Difference in that it is easier with ROM no one touched and stable
Thank you for your interest

GrMo Hady said:
I tried many ways to update my phone but I have a problems in camera ... etc.
Until my phone died and I found a way to reach a stable rom without problems and succeeded
Difference in that it is easier with ROM no one touched and stable
Thank you for your interest
Click to expand...
Click to collapse
This slight difference doesn't make it worthy a new thread.
This is called copying, it's 99% the same.
+ It's not clear and organized for an "easy" tutorial.

GrMo Hady said:
I tried many ways to update my phone but I have a problems in camera ... etc.
Until my phone died and I found a way to reach a stable rom without problems and succeeded
Difference in that it is easier with ROM no one touched and stable
Thank you for your interest
Click to expand...
Click to collapse
Well... As I said already to Karim Kahale before. SmartFlash make more problems than good stuff. I know that LGFlashTools is a bit more complicated but it do much better and clean job. Take a look here. Your threat is the same like Karim Kahale one just with another bin file. You have not opportunity to use large partition, the rom is not Rooted, 90% of the cases you end up with lost IMEI... so you end up with much more work to do.

this topic for a realistic experience
p-vlad said:
Well... As I said already to Karim Kahale before. SmartFlash make more problems than good stuff. I know that LGFlashTools is a bit more complicated but it do much better and clean job. Take a look here. Your threat is the same like Karim Kahale one just with another bin file. You have not opportunity to use large partition, the rom is not Rooted, 90% of the cases you end up with lost IMEI... so you end up with much more work to do.
Click to expand...
Click to collapse
Karim Kahale said:
This slight difference doesn't make it worthy a new thread.
This is called copying, it's 99% the same.
+ It's not clear and organized for an "easy" tutorial.
Click to expand...
Click to collapse
this topic for a realistic experience My Phone works very well and I m not lost my IMEI Tested frequently and successfully.
I do not care if he was in another similarity with the theme is normal to use the same tools
Of course these official rom not touched one of which is for anyone who wants to update and repair only.
All I want that permeated the interest of all
Thank you generally

thanks for this guide it helped me when Lg flash tool diden't work

+1 , I flashed twice with LG Support Tool, but this method is working and my SU760 is alive again.
Thank's!

thanks
sioxz said:
thanks for this guide it helped me when Lg flash tool diden't work
Click to expand...
Click to collapse
thanks

jorrddan said:
+1 , I flashed twice with LG Support Tool, but this method is working and my SU760 is alive again.
Thank's!
Click to expand...
Click to collapse
Thanks)

GrMo Hady said:
Thanks)
Click to expand...
Click to collapse

thanks this saved my day

Install CWM ClockWorkMOD Recovery On Any/Every MediaTek Device

Facebook Page
Facebook Group
Things You Need :
A Rooted Phone
MTK Droid Tool | Click Here to Download
Drivers (These Are Universal Drivers For All MediaTek Devices)--- Click Here To Download | Mirror
Procedure:
1. Download MTK Droid Tool and Drivers From Above
2. Install All Drivers Present in Three Folders
3. Connect Your Device With Computer Through USB Cable And Turn ON USB Debugging
4. From your computer, open MTK Droid Tools that you have downloaded above and extract it to your desired location.
5. Open MTK Droid Tools.exe from the extracted folder (Run as administrator). Wait for the tool to detect your device.
6. Click ROOT button to enable your device. Wait for the progress bar on the Status, see your phone to Grant Superuser access. If the color indicator turns GREEN, then you have successfully enabled root shell for your device.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
7. Now, select the Root, Backup, Recovery tab.
8. Now Click On Backup
9. Wait For The Back Up To Complete

Countinuing
10. After Backup Completed Click On " To Choose the Boot.img File " and Click on Recovery and Boot Button.
11. Now Open Backup Folder Present in MTK Droid Tool Folder
12. Now Open Your Device Backup Folder.Select One Folder. [Important: Make Sure You Open Your Device Backup Folder]
13. There You'll Find Boot File Select That File
14. First Window Will Appear Saying :TO Make CWM Recovery Automatically " Press Yes Button.

Countinuing
15. Second Window Will Appear Click No Button
16. Third Window Will appear Saying " Install Created Recovery To Phone " Press Yes Button
17. Last Window Will Appear Saying " To Reload Phone in Recover " Press Yes Button
Tadaa Now You Have CWM Recovery Installed On Your Device

No Reply ?

gOOD

Well done bro... Nice post. adding this in my thread

Soheir said:
Well done bro... Nice post. adding this in my thread
Click to expand...
Click to collapse
Thanks​

Thanks

Does anybody tried above ? Is backup & restore working with given CWM ?

omdhar said:
Does anybody tried above ? Is backup & restore working with given CWM ?
Click to expand...
Click to collapse
Yes

waqas1412 said:
Yes
Click to expand...
Click to collapse
interessting!! i will try this next week, when my handset arrived!

rionline said:
interessting!! i will try this next week, when my handset arrived!
Click to expand...
Click to collapse
OK

Just for the record :
I was not able to connect the device to the tool even though all the drivers were installed and everything. So what I did was, I opened iRoot and let it connect to the device and waited till the (device is rooted screen) appeared. Then I re-opened the MTKDroid software and it worked afterwards.
Yes, I took full backup and it is working. Haven't tried to restore it but atleast it takes full backup and looks legitimate :good:

suhel28 said:
Just for the record :
I was not able to connect the device to the tool even though all the drivers were installed and everything. So what I did was, I opened iRoot and let it connect to the device and waited till the (device is rooted screen) appeared. Then I re-opened the MTKDroid software and it worked afterwards.
Yes, I took full backup and it is working. Haven't tried to restore it but atleast it takes full backup and looks legitimate :good:
Click to expand...
Click to collapse
so, got my new honor holly yesterday and couldn't wait any longer. rooted, installed cwm and performing my first backup at this very moment. i do hope i will be able to boot afterwards. thumbs up...it is looking promising. has anyone tried restore a cwm backup yet?
by the way, i think our beloved holly molly should get a own forum.
greetings and thank you very much!!

rionline said:
so, got my new honor holly yesterday and couldn't wait any longer. rooted, installed cwm and performing my first backup at this very moment. i do hope i will be able to boot afterwards. thumbs up...it is looking promising. has anyone tried restore a cwm backup yet?
by the way, i think our beloved holly molly should get a own forum.
greetings and thank you very much!!
Click to expand...
Click to collapse
Yes I Had Restored My Phone After Bricking

I like!

waqas1412 said:
15. Second Window Will Appear Click No Button
16. Third Window Will appear Saying " Install Created Recovery To Phone " Press Yes Button
17. Last Window Will Appear Saying " To Reload Phone in Recover " Press Yes Button
Tadaa Now You Have CWM Recovery Installed On Your Device [/QUOTE
mY Honor holly is rooted. I tried to install CWM using MTK Droid tools as per your instructions, but when I click on root button at the bottom right corner of Droid tools, it shows something like, error - system it is not mounted as read/write error - adbd is not installed. Please help
Click to expand...
Click to collapse

makohu said:
waqas1412 said:
15. Second Window Will Appear Click No Button
16. Third Window Will appear Saying " Install Created Recovery To Phone " Press Yes Button
17. Last Window Will Appear Saying " To Reload Phone in Recover " Press Yes Button
Tadaa Now You Have CWM Recovery Installed On Your Device [/QUOTE
mY Honor holly is rooted. I tried to install CWM using MTK Droid tools as per your instructions, but when I click on root button at the bottom right corner of Droid tools, it shows something like, error - system it is not mounted as read/write error - adbd is not installed. Please help
Click to expand...
Click to collapse
when you open MTK Tool and click root button then goto your mobile and see if there a windows will promp for asking root permission
click on allow
if not work then tell me
Click to expand...
Click to collapse

Still not working...PLEASE HELP!!!!
waqas1412 said:
makohu said:
when you open MTK Tool and click root button then goto your mobile and see if there a windows will promp for asking root permission
click on allow
if not work then tell me
Click to expand...
Click to collapse
I gave the root permission for mtk droid tools on my mobile. When I open SuperSU in my honor holly it shows that adb has been granted supersu permission. But still the mtk tool is showing the same error again and again . I have tried it many times. I have micromax doodle 3, it works fine there but is showing this error in honor holly.
Bro I would also like to ask one more question. My phone gets heated up near the camera at the back when I play games and watch videos. Is there any solution for it. Please do reply. Thanks in advance.
Click to expand...
Click to collapse

makohu said:
waqas1412 said:
I gave the root permission for mtk droid tools on my mobile. When I open SuperSU in my honor holly it shows that adb has been granted supersu permission. But still the mtk tool is showing the same error again and again . I have tried it many times. I have micromax doodle 3, it works fine there but is showing this error in honor holly.
Bro I would also like to ask one more question. My phone gets heated up near the camera at the back when I play games and watch videos. Is there any solution for it. Please do reply. Thanks in advance.
Click to expand...
Click to collapse
Install ADBD Insecure Then Try Again
Heatead UP is Common Problem Not Worry About It
Click to expand...
Click to collapse