Hi, please help me. My Samsung Focus 1.3 doesn't boot, only starts and gets stuck on samsung blinking screen. I've tryed to make hard reset, but keys don't work. It only accept download mode. What can I do?
Try either restoring a Zune update, or re-flashing the stock ROM. There should be downloads and instructions for the latter in the device-specific part of the forum.
Alternatively, make sure the SD card (if you use one) is seated correctly. However, I think the most likely problem is just hardware failure, in which case you probably need to get the phone replaced (I assume it's under warranty).
Hi, it's impossible to start on MAGLDGR mode. This phone only accept Download mode, the yellow triangle. There is another way to re-flash from download mode?
After flashing with Focus 1.3 i917 AT&T USA and i917R ROGERS CANADA RETAIL ROMs, using WP7 downloader v. 7.21, it's stucked and just displays SAMSUNG.
Sorry, almost forget, Zune doesn't recognize my device.
I re-flash using I917UCK3 with similar results. This are the processes on WP7:
Open Phone image at : c:\users\nsc3\documents\jm\wp7\samsung-i917-focus-firmware-ucjk2-att-usa\signed_phone_cetus_att.bin
Open Eboot image at : c:\users\nsc3\documents\jm\wp7\samsung-i917-focus-firmware-ucjk2-att-usa\signed_eboot_cetus_att.eb0
Open PDA image at : c:\users\nsc3\documents\jm\wp7\samsung-i917-focus-firmware-ucjk2-att-usa\signed_pda_cetus_att.nb0
Open CSC image at : c:\users\nsc3\documents\jm\wp7\samsung-i917-focus-firmware-ucjk2-att-usa\signed_csc_cetus_att_i917attjk2.csc
Detect COM17 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH UNLOCK
[Channel 0] FLASH UNLOCK Success!!!
[Channel 0] Send Partition Table
[Channel 0] Partition Table is correct
[Channel 0] Erase MIBIB Region
[Channel 0] Write MIBIB Data
[Channel 0] MIBIB Download Success!!
[Channel 0] Erase FSBL Region
[Channel 0] Write FSBL Data
[Channel 0] FSBL Download Success!!
[Channel 0] Erase OSBL Region
[Channel 0] Write OSBL Data
[Channel 0] OSBL Download Success!!
[Channel 0] Erase AMSS Region
[Channel 0] Write AMSS Data
[Channel 0] AMSS Download Success!!
[Channel 0] Erase DSP1 Region
[Channel 0] Write DSP1 Data
[Channel 0] DSP1 Download Success!!
[Channel 0] Erase APPSBL Region
[Channel 0] Write APPSBL Data
[Channel 0] APPSBL Download Success!!
[Channel 0] Erase CSC Region
[Channel 0] Write CSC Data
[Channel 0] CSC Download Success!!
[Channel 0] Erase PDA Region
[Channel 0] Write PDA Data
[Channel 0] PDA Download Success!!
[Channel 0] FLASH LOCK
Detect COM17 Port
Samsung Focus doesn't boot
jmweb said:
I re-flash using I917UCK3 with similar results. This are the processes on WP7:
Open Phone image at : c:\users\nsc3\documents\jm\wp7\samsung-i917-focus-firmware-ucjk2-att-usa\signed_phone_cetus_att.bin
Open Eboot image at : c:\users\nsc3\documents\jm\wp7\samsung-i917-focus-firmware-ucjk2-att-usa\signed_eboot_cetus_att.eb0
Open PDA image at : c:\users\nsc3\documents\jm\wp7\samsung-i917-focus-firmware-ucjk2-att-usa\signed_pda_cetus_att.nb0
Open CSC image at : c:\users\nsc3\documents\jm\wp7\samsung-i917-focus-firmware-ucjk2-att-usa\signed_csc_cetus_att_i917attjk2.csc
Detect COM17 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH UNLOCK
[Channel 0] FLASH UNLOCK Success!!!
[Channel 0] Send Partition Table
[Channel 0] Partition Table is correct
[Channel 0] Erase MIBIB Region
[Channel 0] Write MIBIB Data
[Channel 0] MIBIB Download Success!!
[Channel 0] Erase FSBL Region
[Channel 0] Write FSBL Data
[Channel 0] FSBL Download Success!!
[Channel 0] Erase OSBL Region
[Channel 0] Write OSBL Data
[Channel 0] OSBL Download Success!!
[Channel 0] Erase AMSS Region
[Channel 0] Write AMSS Data
[Channel 0] AMSS Download Success!!
[Channel 0] Erase DSP1 Region
[Channel 0] Write DSP1 Data
[Channel 0] DSP1 Download Success!!
[Channel 0] Erase APPSBL Region
[Channel 0] Write APPSBL Data
[Channel 0] APPSBL Download Success!!
[Channel 0] Erase CSC Region
[Channel 0] Write CSC Data
[Channel 0] CSC Download Success!!
[Channel 0] Erase PDA Region
[Channel 0] Write PDA Data
[Channel 0] PDA Download Success!!
[Channel 0] FLASH LOCK
Detect COM17 Port
Click to expand...
Click to collapse
Hello, i have got the same probleme, please how did you resolve the problème ?
Hi,
my Nexus 5 was plugged on my laptop.
After a while I saw, that my phone rebooted. I saw the google logo.
I pressed and hold the "Power Button".
My phone booted again and stuck in the booting animation.
This happened three days ago.
I tried so many things. It's not working.
Maybe I messed up the partition.
The first thing I tried was to flash the android factory image like this (Flashing instructions - don't forget to press the button "ACKNOWLEDGE"):
https://developers.google.com/android/images
I first thought, that maybe the eMMC is fried.
I checked this like this ( https://forum.xda-developers.com/showthread.php?t=1284196 ):
Code:
adb shell
dmesg | grep mmc0
I didn't get a message like this:
Code:
mmc0: failed to get card ready
mmc0: reinit card
mmc0: Starting deferred resume
mmc0: Deferred resume failed
I read, that I should change to usb 2.0 port and the usb cable.
I've also a Galaxy nexus. I've tried to flash a new stock with WugFresh. Everything worked with the usb 2.0 port and the usb cable.
When I tried to do that with my nexus 5 nothing works. I get this failure messages:
FAILED (remote: flash write failure)
I used TWRP (twrp-3.0.3-0-hammerhead.img) and clockwork mod (recovery-clockwork-touch-6.0.4.4-hammerhead.img).
The main errors I get:
Can't mount /data
...
E: Can't mount /cache/recovery/command
E: Can't mount /cache/recovers/log
E: Can't open /cache/recovers/log
...
I really don't know what to do.
Is there a method to build the partition new? Or what else can I do?
Thank you for any help.
Does the bootloader relock when rebooted after being unlocked? Have you tried flashing the stock KK ROM?
Yes. It relocks when rebooted.
Do you mean Kit Kat? No, I didn't. I've tried only the new versions like 6.0.1 (MOB31E), 6.0.1 (M4B30Z, Dec 2016).
I will try KK Rom later.
I've downloaded this factory image:
"hammerhead" for Nexus 5 (GSM/LTE)
4.4.4 (KTU84P)
from here: https://developers.google.com/android/images
This is the original "flash-all.bat" file:
Code:
@ECHO OFF
PATH=%PATH%;"%SYSTEMROOT%\System32"
fastboot flash bootloader bootloader-hammerhead-hhz11k.img
fastboot reboot-bootloader
ping -n 5 127.0.0.1 >nul
fastboot flash radio radio-hammerhead-m8974a-2.0.50.1.16.img
fastboot reboot-bootloader
ping -n 5 127.0.0.1 >nul
fastboot -w update image-hammerhead-ktu84p.zip
echo Press any key to exit...
pause >nul
exit
I've changed the "flash-all.bat" a little bit. I added this line "fastboot oem unlock". When I not add "fastboot oem unlock", I get a message like "not unlocked":
Code:
@ECHO OFF
PATH=%PATH%;"%SYSTEMROOT%\System32"
[B]fastboot oem unlock[/B]
fastboot flash bootloader bootloader-hammerhead-hhz11k.img
fastboot reboot-bootloader
[B]fastboot oem unlock[/B]
ping -n 5 127.0.0.1 >nul
fastboot flash radio radio-hammerhead-m8974a-2.0.50.1.16.img
fastboot reboot-bootloader
[B]fastboot oem unlock[/B]
ping -n 5 127.0.0.1 >nul
fastboot -w update image-hammerhead-ktu84p.zip
echo Press any key to exit...
pause >nul
exit
I've started the "flash-all.bat". This is the output:
Code:
target reported max download size of 1073741824 bytes
sending 'bootloader' (2508 KB)...
OKAY [ 0.203s]
writing 'bootloader'...
FAILED (remote: flash write failure)
finished. total time: 0.406s
rebooting into bootloader...
OKAY [ 0.094s]
finished. total time: 0.094s
< waiting for any device >
...
OKAY [ 4.109s]
finished. total time: 4.109s
target reported max download size of 1073741824 bytes
sending 'radio' (45409 KB)...
OKAY [ 1.625s]
writing 'radio'...
FAILED (remote: flash write failure)
finished. total time: 2.844s
rebooting into bootloader...
OKAY [ 0.109s]
finished. total time: 0.109s
< waiting for any device >
...
OKAY [ 6.250s]
finished. total time: 6.250s
target reported max download size of 1073741824 bytes
archive does not contain 'boot.sig'
archive does not contain 'recovery.sig'
archive does not contain 'system.sig'
archive does not contain 'vendor.img'
wiping userdata...
Creating filesystem with parameters:
Size: 13725835264
Block size: 4096
Blocks per group: 32768
Inodes per group: 8144
Inode size: 256
Journal blocks: 32768
Label:
Blocks: 3351034
Block groups: 103
Reserved block group size: 823
Created filesystem with 11/838832 inodes and 93654/3351034 blocks
wiping cache...
Creating filesystem with parameters:
Size: 734003200
Block size: 4096
Blocks per group: 32768
Inodes per group: 7472
Inode size: 256
Journal blocks: 2800
Label:
Blocks: 179200
Block groups: 6
Reserved block group size: 47
Created filesystem with 11/44832 inodes and 5813/179200 blocks
--------------------------------------------
Bootloader Version...: HHZ20f
Baseband Version.....: M8974A-2.0.50.2.29
Serial Number........: 04ae306b2524b05b
--------------------------------------------
checking product...
OKAY [ 0.109s]
checking version-bootloader...
FAILED
Device version-bootloader is 'HHZ20f'.
Update requires 'HHZ11k'.
finished. total time: 0.594s
Press any key to exit...
Before flashing again, unlock the bootloader and immediately reboot the phone into fastboot. Does the bootloader relock when the phone is rebooted? If yes, the memory chip is damaged.
audit13 said:
Before flashing again, unlock the bootloader and immediately reboot the phone into fastboot. Does the bootloader relock when the phone is rebooted? If yes, the memory chip is damaged.
Click to expand...
Click to collapse
I have the same problem and after doing that I can see that my eMMC is in fact fried since the bootloader relocks. I was wondering, where is the bootloader/fastboot stored on the device? On the CPU/GPU/RAM stack or on the eMMC. If I swap out the eMMC chip, will I still be able to access it (the bootloader) with a blank eMMC or is it on the eMMC as well? I'm trying to find out what are the steps to format and partition the eMMC after a new one is installed...
I don't know where the bootloader is located. When I determine that there is a problem with the memory chip, I just replace the motherboard.
audit13 said:
I don't know where the bootloader is located. When I determine that there is a problem with the memory chip, I just replace the motherboard.
Click to expand...
Click to collapse
Thank you very much for sharing your experience!
I would assume that the bootloader is located on the eMMC since I can't write to the bootloader (or any other) partition from fastboot. I'll have to look into solutions during the weekend since I don't have much time until then, but replacing the MB is a no go for me because of the price.
I'm not sure where you are located but I live in a big city in Canada where I can find deals for people selling Nexus 5 phones with smashed screens and working internal components.
Good luck and please share your results. Thanks.
@audit13: When I unlock the bootloader and then reboot the phone into fastboot. The bootloader relocks.
Is the memory chip now really damaged? Can't I do nothing? My N5 is three years old. I don't want to pay a lot of money for a main board.
The cheapest solution for a damaged emmc chip may be to buy a used Nexus 5 with a smashed screen and working motherboard. This is what I had to do for 2 phones with self re-locking bootloaders.
I bought a display damaged nexus 5. It arrived today. Changed the main board. And Voila! It's working.
The other guy has installed this build:
"hammerhead" for Nexus 5 (GSM/LTE)
6.0.1 (MOB30H)
No my question: Which factory image should I install?
https://developers.google.com/android/images
"hammerhead" for Nexus 5 (GSM/LTE)
...
6.0.1 (MOB30H)
6.0.1 (MOB30M)
6.0.1 (MOB30P)
6.0.1 (MOB30Y)
6.0.1 (MOB31E)
6.0.1 (M4B30X, Oct 2016)
6.0.1 (M4B30Z, Dec 2016)
I'm not sure, because the last two has dates. Are they meaning something (I mean, are they special builds), because the other factory images don't have dates.
Or should I do this:
https://developers.google.com/android/ota
OTA binary image files that allow you to manually update your Nexus or Pixel device. This has the same effect of flashing the corresponding factory images, but without the need of wiping the device.
"hammerhead" for Nexus 5 (GSM/LTE)
6.0.1 (M4B30Z)
Is OTA better than factory images?
OK. I've installed this version 6.0.1 (M4B30Z, Dec 2016). Everything works.
my p2 got hard brick, no way to enter to fastboot and recovery, even with any configuration button, when connected to pc i only get red blinking led, screen show blank, and in pc device manager just show Qualcomm HS-USB QDLoader 9008, no solution how to Resurrected from death even with qfil tool or miflash tool, luckily now back to live after 3 month death, here what i did:
before all started, first recharge your p2 for 1/2 an hour to make sure enough battery more than 20%,
install lenovo p2 usb driver: https://mega.nz/#!rQgjACaJ!-ZVi7TDUgtVaUVEe7yGZ-jr4ijarO704T7x2IQdVjeU,
install qualcomm usb driver:
https://mega.nz/#!GNRWiQrJ!ASpU78MPYzh-I4EUiK_ba5YtlZUTQHP_r_P4Dd7hSZg
reboot your pc,
connect your p2 to pc,
go to pc device manager, you will see in pc device manager like in screenshot, if you didn't see like that press vol +and- togather with power button, hold all of them till appear like screenshoot
now download zip file blankflash tool https://mega.nz/#!PIZ0GChJ!3RhdFN38IajIVYQT_5ppZGxcconOntG1-d75vNK1Vg8, extract it, and place it in c folder your pc,
open folder and run blank-flash.bat,
automaticly your p2 will start reboot to fastboot,
or if your rom still intack p2 will reboot to system os,
Or if no os, now you can flash rom from fastboot
congratulation now your p2 back to live.
hendibudi said:
my p2 got hard brick, no way to enter to fastboot and recovery, even with any configuration button, when connected to pc i only get red blinking led, screen show blank, and in pc device manager just show Qualcomm HS-USB QDLoader 9008, no solution how to Resurrected from death even with qfil tool or miflash tool, luckily now back to live after 3 month death, here what i did:
before all started, first recharge your p2 for 1/2 an hour to make sure enough battery more than 20%,
install lenovo p2 driver,
reboot your pc,
connect your p2 to pc,
go to pc device manager,
you will see in pc device manager like in screenshot,
now download zip file blankflash tool, extract it, and place it in c folder your pc,
open folder and run blank-flash.bat,
automaticly your p2 will start reboot to fastboot,
or if your rom still intack p2 will reboot to system os,
congratulation now your p2 back to live
Click to expand...
Click to collapse
Thanks! Please post a link to download that BlankFlash Tool.
kermex said:
Thanks! Please post a link to download that BlankFlash Tool.
Click to expand...
Click to collapse
When upload finished there is link
hendibudi said:
When upload finished there is link
Click to expand...
Click to collapse
Great! Thanks again!
hendibudi said:
my p2 got hard brick, no way to enter to fastboot and recovery, even with any configuration button, when connected to pc i only get red blinking led, screen show blank, and in pc device manager just show Qualcomm HS-USB QDLoader 9008, no solution how to Resurrected from death even with qfil tool or miflash tool, luckily now back to live after 3 month death, here what i did:
before all started, first recharge your p2 for 1/2 an hour to make sure enough battery more than 20%,
install lenovo p2 driver,
reboot your pc,
connect your p2 to pc,
go to pc device manager,
you will see in pc device manager like in screenshot,
now download zip file blankflash tool, extract it, and place it in c folder your pc,
open folder and run blank-flash.bat,
automaticly your p2 will start reboot to fastboot,
or if your rom still intack p2 will reboot to system os,
congratulation now your p2 back to live
Click to expand...
Click to collapse
Waiting for download link. Will this fix no signal issue? Does it have non-holos.bin? Also if my device is working can I use that tool?
Sent from my Lenovo P2 using Tapatalk
abhayruparel said:
Waiting for download link. Will this fix no signal issue? Does it have non-holos.bin? Also if my device is working can I use that tool?
Sent from my Lenovo P2 using Tapatalk
Click to expand...
Click to collapse
No download link. I'm waiting for it, too. Maybe he doesn't want to share this.
kermex said:
No download link. I'm waiting for it, too. Maybe he doesn't want to share this.
Click to expand...
Click to collapse
Be patients for couple of days, compare to me waiting 3 months my p2 death back to live, cause i have limited data
hendibudi said:
Be patients for couple of days, compare to me waiting 3 months my p2 death back to live, cause i have limited data
Click to expand...
Click to collapse
Why you don't use wifi?!
kermex said:
Why you don't use wifi?!
Click to expand...
Click to collapse
Where?
hendibudi said:
Where?
Click to expand...
Click to collapse
He meant that why don't you use Wi-Fi for uploading. Please reply to #5
OK, thanks! Just forgot about this.
the laptop loses the portconnection and I get
readfile() failed , getlastError()=31
anny idea how to fix this?
Datech2 said:
after identifying CPU I get
the laptop loses the portconnection and I get
readfile() failed , getlastError()=31
anny idea how to fix this?
Click to expand...
Click to collapse
How about p2
hendibudi said:
How about p2
Click to expand...
Click to collapse
no reaction , the red led keeps blinking ,
when push de power button and the volume + he reconnects
Datech2 said:
no reaction , the red led keeps blinking ,
when push de power button and the volume + he reconnects
Click to expand...
Click to collapse
Check first post step by step
Yes blankflash method works. But I must push VolDown + Power buttons in the right moment to done it properly.
So below are my instructions. I also put my log. Without pushing the buttons I have IOError.
1. Install Latest Qualcomm 9008 Driver from link below and restart PC:
androidbrick.com/download/latest-2017-qualcomm-diag-qd-loader-windows-10-drivers-signed/
2. Download flashbank.zip from link below
mega.nz/#!PIZ0GChJ!3RhdFN38IajIVYQT_5ppZGxcconOntG1-d75vNK1Vg8
3. Unpack archive to C:\lenovo (or other directory if you are poweruser and you will know what to change in steps below)
4. Open cmd and go to C:\lenovo\
5. Turn off the phone, and connect to USB, in Device Manager you should see Qualcomm 9008 device in Ports (LPT & COMM) section (or something like this)
6. Push VolumeDown + Power buttons together
7. In cmd run command below
qboot blank-flash
8. When in cmd text below appear, release VolumeDown + Power buttons
Waiting for firehose to get ready ......
9. Now the phone should boot into Fastboot
My log:
C:\lenovo>qboot blank-flash
Opening device: \\.\COM3
OKAY [ 0.004s]
Detecting device
...cpu.id = 70 (0x46)
...cpu.sn = 2326272297 (0x8aa81929)
OKAY [ 7.010s]
Opening singleimage
OKAY [ 0.001s]
Loading package
...filename = bootloader.qboot.xml
OKAY [ 0.011s]
Loading programmer
...filename = programmer.mbn
OKAY [ 0.007s]
Sending programmer
OKAY [ 0.247s]
Handling things over to programmer
Waiting for firehose to get ready ......
Identifying CPU
...MSM8953 1.1
Storage Information
...physical partition number: 0
...num_partition_sectors=61071360
...SECTOR_SIZE_IN_BYTES=512
...num_physical_partitions=3
...MFR_ID=144
...OEM_ID=74
...Product name=HBG4a2
...{"storage_info": {"total_blocks":61071360, "block_size":512, "page_size":512, "num_physical":3, "mfr_id":144, "serial_num":574148832, "fw_version":"164","mem_type":"eMMC", "prod_name":"HBG4a2"}}
Flashing partition sbl1 with sbl1.mbn (375KB)
....100%
Flashing partition sbl1bak with sbl1.mbn (375KB)
....100%
Flashing partition rpm with rpm.mbn (170KB)
..100%
Flashing partition rpmbak with rpm.mbn (170KB)
..100%
Flashing partition tz with tz.mbn (1447KB)
.....100%
Flashing partition tzbak with tz.mbn (1447KB)
.....100%
Flashing partition devcfg with devcfg.mbn (36KB)
..100%
Flashing partition devcfgbak with devcfg.mbn (36KB)
..100%
Flashing partition aboot with emmc_appsboot.mbn (854KB)
....100%
Flashing partition abootbak with emmc_appsboot.mbn (854KB)
....100%
Flashing partition lksecapp with lksecapp.mbn (56KB)
....100%
Flashing partition lksecappbak with lksecapp.mbn (56KB)
....100%
Flashing partition cmnlib with cmnlib.mbn (196KB)
..100%
Flashing partition cmnlibbak with cmnlib.mbn (196KB)
..100%
Flashing partition cmnlib64 with cmnlib64.mbn (249KB)
..100%
Flashing partition cmnlib64bak with cmnlib64.mbn (249KB)
..100%
Flashing partition keymaster with keymaster.mbn (220KB)
..100%
Flashing partition keymasterbak with keymaster.mbn (220KB)
..100%
Flashing partition prov with prov32.mbn (64KB)
....100%
Flashing partition PrimaryGPT with gpt_main0.bin (17KB)
..100%
Flashing partition BackupGPT with gpt_backup0.bin (16KB)
....100%
Patching DISK -- Update last partition 56 'userdata' with actual size in Primary Header.
Patching DISK -- Update last partition 56 'userdata' with actual size in Backup Header.
Patching DISK -- Update Primary Header with LastUseableLBA.
Patching DISK -- Update Backup Header with LastUseableLBA.
Patching DISK -- Update Primary Header with BackupGPT Header Location.
Patching DISK -- Update Backup Header with CurrentLBA.
Patching DISK -- Update Backup Header with Partition Array Location.
Patching DISK -- Update Primary Header with CRC of Partition Array.
Patching DISK -- Update Backup Header with CRC of Partition Array.
Patching DISK -- Zero Out Header CRC in Primary Header.
Patching DISK -- Update Primary Header with CRC of Primary Header.
Patching DISK -- Zero Out Header CRC in Backup Header.
Patching DISK -- Update Backup Header with CRC of Backup Header.
OKAY [ 4.572s]
finished. total time: 11.861s
It worked like charm.[emoji106][emoji106][emoji106]
Sent from my Lenovo P2a42 using Tapatalk
I lost sim modem after flashing stock firmware
Anyway to restore it?
You'd only do this to restore fastboot or, if possible, boot into an existing OS, right? There's no way of recovering a lost signal by flashing modem?
slimok5 said:
Yes blankflash method works. But I must push VolDown + Power buttons in the right moment to done it properly.
So below are my instructions. I also put my log. Without pushing the buttons I have IOError.
1. Install Latest Qualcomm 9008 Driver from link below and restart PC:
androidbrick.com/download/latest-2017-qualcomm-diag-qd-loader-windows-10-drivers-signed/
2. Download flashbank.zip from link below
mega.nz/#!PIZ0GChJ!3RhdFN38IajIVYQT_5ppZGxcconOntG1-d75vNK1Vg8
3. Unpack archive to C:\lenovo (or other directory if you are poweruser and you will know what to change in steps below)
4. Open cmd and go to C:\lenovo\
5. Turn off the phone, and connect to USB, in Device Manager you should see Qualcomm 9008 device in Ports (LPT & COMM) section (or something like this)
6. Push VolumeDown + Power buttons together
7. In cmd run command below
qboot blank-flash
8. When in cmd text below appear, release VolumeDown + Power buttons
Waiting for firehose to get ready ......
9. Now the phone should boot into Fastboot
My log:
C:\lenovo>qboot blank-flash
Opening device: \.\COM3
OKAY [ 0.004s]
Detecting device
...cpu.id = 70 (0x46)
...cpu.sn = 2326272297 (0x8aa81929)
OKAY [ 7.010s]
Opening singleimage
OKAY [ 0.001s]
Loading package
...filename = bootloader.qboot.xml
OKAY [ 0.011s]
Loading programmer
...filename = programmer.mbn
OKAY [ 0.007s]
Sending programmer
OKAY [ 0.247s]
Handling things over to programmer
Waiting for firehose to get ready ......
Identifying CPU
...MSM8953 1.1
Storage Information
...physical partition number: 0
...num_partition_sectors=61071360
...SECTOR_SIZE_IN_BYTES=512
...num_physical_partitions=3
...MFR_ID=144
...OEM_ID=74
...Product name=HBG4a2
...{"storage_info": {"total_blocks":61071360, "block_size":512, "page_size":512, "num_physical":3, "mfr_id":144, "serial_num":574148832, "fw_version":"164","mem_type":"eMMC", "prod_name":"HBG4a2"}}
Flashing partition sbl1 with sbl1.mbn (375KB)
....100%
Flashing partition sbl1bak with sbl1.mbn (375KB)
....100%
Flashing partition rpm with rpm.mbn (170KB)
..100%
Flashing partition rpmbak with rpm.mbn (170KB)
..100%
Flashing partition tz with tz.mbn (1447KB)
.....100%
Flashing partition tzbak with tz.mbn (1447KB)
.....100%
Flashing partition devcfg with devcfg.mbn (36KB)
..100%
Flashing partition devcfgbak with devcfg.mbn (36KB)
..100%
Flashing partition aboot with emmc_appsboot.mbn (854KB)
....100%
Flashing partition abootbak with emmc_appsboot.mbn (854KB)
....100%
Flashing partition lksecapp with lksecapp.mbn (56KB)
....100%
Flashing partition lksecappbak with lksecapp.mbn (56KB)
....100%
Flashing partition cmnlib with cmnlib.mbn (196KB)
..100%
Flashing partition cmnlibbak with cmnlib.mbn (196KB)
..100%
Flashing partition cmnlib64 with cmnlib64.mbn (249KB)
..100%
Flashing partition cmnlib64bak with cmnlib64.mbn (249KB)
..100%
Flashing partition keymaster with keymaster.mbn (220KB)
..100%
Flashing partition keymasterbak with keymaster.mbn (220KB)
..100%
Flashing partition prov with prov32.mbn (64KB)
....100%
Flashing partition PrimaryGPT with gpt_main0.bin (17KB)
..100%
Flashing partition BackupGPT with gpt_backup0.bin (16KB)
....100%
Patching DISK -- Update last partition 56 'userdata' with actual size in Primary Header.
Patching DISK -- Update last partition 56 'userdata' with actual size in Backup Header.
Patching DISK -- Update Primary Header with LastUseableLBA.
Patching DISK -- Update Backup Header with LastUseableLBA.
Patching DISK -- Update Primary Header with BackupGPT Header Location.
Patching DISK -- Update Backup Header with CurrentLBA.
Patching DISK -- Update Backup Header with Partition Array Location.
Patching DISK -- Update Primary Header with CRC of Partition Array.
Patching DISK -- Update Backup Header with CRC of Partition Array.
Patching DISK -- Zero Out Header CRC in Primary Header.
Patching DISK -- Update Primary Header with CRC of Primary Header.
Patching DISK -- Zero Out Header CRC in Backup Header.
Patching DISK -- Update Backup Header with CRC of Backup Header.
OKAY [ 4.572s]
finished. total time: 11.861s
Click to expand...
Click to collapse
Hey I am stack on identifying the cpu
---------- Post added at 01:43 PM ---------- Previous post was at 01:34 PM ----------
slimok5 said:
Yes blankflash method works. But I must push VolDown + Power buttons in the right moment to done it properly.
So below are my instructions. I also put my log. Without pushing the buttons I have IOError.
1. Install Latest Qualcomm 9008 Driver from link below and restart PC:
androidbrick.com/download/latest-2017-qualcomm-diag-qd-loader-windows-10-drivers-signed/
2. Download flashbank.zip from link below
mega.nz/#!PIZ0GChJ!3RhdFN38IajIVYQT_5ppZGxcconOntG1-d75vNK1Vg8
3. Unpack archive to C:\lenovo (or other directory if you are poweruser and you will know what to change in steps below)
4. Open cmd and go to C:\lenovo\
5. Turn off the phone, and connect to USB, in Device Manager you should see Qualcomm 9008 device in Ports (LPT & COMM) section (or something like this)
6. Push VolumeDown + Power buttons together
7. In cmd run command below
qboot blank-flash
8. When in cmd text below appear, release VolumeDown + Power buttons
Waiting for firehose to get ready ......
9. Now the phone should boot into Fastboot
My log:
C:\lenovo>qboot blank-flash
Opening device: \.\COM3
OKAY [ 0.004s]
Detecting device
...cpu.id = 70 (0x46)
...cpu.sn = 2326272297 (0x8aa81929)
OKAY [ 7.010s]
Opening singleimage
OKAY [ 0.001s]
Loading package
...filename = bootloader.qboot.xml
OKAY [ 0.011s]
Loading programmer
...filename = programmer.mbn
OKAY [ 0.007s]
Sending programmer
OKAY [ 0.247s]
Handling things over to programmer
Waiting for firehose to get ready ......
Identifying CPU
...MSM8953 1.1
Storage Information
...physical partition number: 0
...num_partition_sectors=61071360
...SECTOR_SIZE_IN_BYTES=512
...num_physical_partitions=3
...MFR_ID=144
...OEM_ID=74
...Product name=HBG4a2
...{"storage_info": {"total_blocks":61071360, "block_size":512, "page_size":512, "num_physical":3, "mfr_id":144, "serial_num":574148832, "fw_version":"164","mem_type":"eMMC", "prod_name":"HBG4a2"}}
Flashing partition sbl1 with sbl1.mbn (375KB)
....100%
Flashing partition sbl1bak with sbl1.mbn (375KB)
....100%
Flashing partition rpm with rpm.mbn (170KB)
..100%
Flashing partition rpmbak with rpm.mbn (170KB)
..100%
Flashing partition tz with tz.mbn (1447KB)
.....100%
Flashing partition tzbak with tz.mbn (1447KB)
.....100%
Flashing partition devcfg with devcfg.mbn (36KB)
..100%
Flashing partition devcfgbak with devcfg.mbn (36KB)
..100%
Flashing partition aboot with emmc_appsboot.mbn (854KB)
....100%
Flashing partition abootbak with emmc_appsboot.mbn (854KB)
....100%
Flashing partition lksecapp with lksecapp.mbn (56KB)
....100%
Flashing partition lksecappbak with lksecapp.mbn (56KB)
....100%
Flashing partition cmnlib with cmnlib.mbn (196KB)
..100%
Flashing partition cmnlibbak with cmnlib.mbn (196KB)
..100%
Flashing partition cmnlib64 with cmnlib64.mbn (249KB)
..100%
Flashing partition cmnlib64bak with cmnlib64.mbn (249KB)
..100%
Flashing partition keymaster with keymaster.mbn (220KB)
..100%
Flashing partition keymasterbak with keymaster.mbn (220KB)
..100%
Flashing partition prov with prov32.mbn (64KB)
....100%
Flashing partition PrimaryGPT with gpt_main0.bin (17KB)
..100%
Flashing partition BackupGPT with gpt_backup0.bin (16KB)
....100%
Patching DISK -- Update last partition 56 'userdata' with actual size in Primary Header.
Patching DISK -- Update last partition 56 'userdata' with actual size in Backup Header.
Patching DISK -- Update Primary Header with LastUseableLBA.
Patching DISK -- Update Backup Header with LastUseableLBA.
Patching DISK -- Update Primary Header with BackupGPT Header Location.
Patching DISK -- Update Backup Header with CurrentLBA.
Patching DISK -- Update Backup Header with Partition Array Location.
Patching DISK -- Update Primary Header with CRC of Partition Array.
Patching DISK -- Update Backup Header with CRC of Partition Array.
Patching DISK -- Zero Out Header CRC in Primary Header.
Patching DISK -- Update Primary Header with CRC of Primary Header.
Patching DISK -- Zero Out Header CRC in Backup Header.
Patching DISK -- Update Backup Header with CRC of Backup Header.
OKAY [ 4.572s]
finished. total time: 11.861s
Click to expand...
Click to collapse
Phone boot into fastboot but no light