Hi folks,
My DS is currently running ViperSaga, and it's affected by a camera bug which is supposedly fixed by swapping my radio version (10.08.04_M) to the one from the ICU RUU. Since I'm S-ON (though htcdev-unlocked -- of course, I will do 'fastboot oem lock' before proceeding any further ) and would prefer to stay that way, I'll simply need to flash the entire ICS RUU in order to upgrade my radio. However, my USB connection is not 100%, and it has a tendency to drop out after the phone has been connected for a random number of minutes (the phone then goes into charge-only mode and is no longer seen by adb). Obviously, it would be bad if this happened while running the official RUU.
My first thought was to flash the RUU manually (fastboot erase cache, fastboot oem rebootRUU, fastboot flash zip rom.zip), and if the USB were to cut out, to simply reconnect and re-issue the fastboot flash zip rom.zip command. However, I did some Googling and found that there was another way, namely to put the rom.zip onto a mSD card renamed to PG88IMG.zip (the same way you S-OFF folks flash your radios ) and to let hboot do the upgrade all on its own.
My question is this: when upgrading hboot (as I will, from 2.00.0002 to 2.02.0002), you are often asked to flash the image twice if you do it via fastboot oem rebootRUU. (hboot pre-update! please flush image again immediately). Does the PG88IMG.zip flasher in hboot understand this and does it automatically flash itself a second time if needed?. I.e.: is it safe to upgrade hboot through PG88IMG.zip?
Sorry for the long post, but I wanted to make sure I'm as clear as possible as this is my main phone and I'd rather not brick it (though being able to take 5MP pictures on ViperSaga would be nice )
Thank you for your help!
I've decided to follow the following procedure:
1) reboot into Linux (USB seems more stable there)
2)
Code:
fastboot oem lock
fastboot erase cache
fastboot oem rebootRUU
fastboot flash zip rom.zip
(repeat last command because the flasher asked me to, as expected)
fastboot reboot-bootloader
3) Allow the system to boot, enable USB debugging, adb reboot-bootloader
4) re-unlock bootloader
5) flash recovery, boot.img, and ViperSaga
All is well
Oh no! Looks like your kindle wont boot! Dont worry, this thread got ya covered. Welcome to the Unbricking Station!
NOTE: I DO NOT TAKE RESPONSIBILITY IF THESE METHODS WILL MAKE YOUR DEVICE WORSE. USE AT YOUR OWN RISK.
1. I have a red screen at boot-up. What should i do?
This happens when you install the 2nd bootloader when you are on
software version 7.3.0 or higher, even though you downgraded to 7.2.3 the 7.3.0-7.X.X bootloader will retain.
SOLUTION: Flashing the 7.2.3 uboot file will do the trick by booting into fastboot with a fastboot cable and type these commands
fastboot -i 0x1949 flash bootloader kfhd7-u-boot-prod-7.2.3.bin
or if that doesnt work and you have backed-up your stock boot, recovery, and system type these
fastboot -i 0x1949 flash boot stock-boot.img
fastboot -i 0x1949 flash recovery stock-recovery.img
fastboot -i 0x1949 flash system stock-system.img
2. When i bootup it just gets stuck in the blue kindle fire logo or the bootanimation. What should i do?
This happens when you installed the 2nd bootloader successfully and you might have killed a binary during stack installation, or you might have messed with the system files of your OS.
SOLUTION: If you can boot up to TWRP (recovery), you can just flash the stock Amazon OS or CyanogenMod once again.
Booting to recovery can be done by just pressing the volume up button while in the ORANGE kindle fire logo, after that just press install and select which OS you had before the error.
Amazon OS: http://forum.xda-developers.com/showthread.php?t=2218475
CyanogenMod 10.1: http://forum.xda-developers.com/showthread.php?t=2245335
Use adb sideload, if you don't have these files on the kindle's internal storage.
Go to advanced, then to ADB Sideload.
While in your computer, go to a command prompt and type
Adb sideload *osfilename*.zip
After that, it will install itself and you are good to go!
3. When i flashed FireFireFire/broke the bootloader, it wont startup, what should I do?
You flashed a incompatible bootloader (1st Gen) on a 2nd Gen device.
SOLUTION: Your best bet is just send it back for a replacement.
If anyone have anymore methods to unbrick their device, send me a PM to get a chance for your method to be featured in this thread.
Credits to Hashcode for the bootloader and to Amazon for a wonderful device. xD
I've got a BIG problem with my new Pixel 5. I've successfully rooted it and had it operating for a day.
I then decided to boot into recovery mode just to see what the new stock recovery looks like (I used to use TWRP.).
BIG MISTAKE!
All I got was the error icon that I've seen in the past meaning that no recovery image is available. OK, so I try to just try to do a simple reboot. I'm taken back to the same place.
Now I try to reload Android. No luck! I'm stuck on:
"Device product is 'unknown'"
Update requires 'bramble'.
HELP!!!!
In the file android-info.txt, what would happen if I patched the line
require board=bramble
to
require board=unknown
Did you figure this out? I'm facing the same issue with my Pixel 5.
Edit: I figured it out. If you are having an issue with the 'flash-all.bat' command like we were, you just need to manually push the individual files and it should boot you back up into stock.
Run these commands:
1. fastboot flash bootloader <bootloader image file>
2. fastboot reboot-bootloader
3. fastboot flash radio <radio image file>.img
4. fastboot reboot-bootloader
5. fastboot update <image zip file>.zip
6. fastboot reboot
All of the reboot-bootloader commands may be redundant but it worked for me. It booted me into stock, verified I was unrooted with Root Checker, then proceeded to reboot back into the bootloader and 'fastboot flashing lock' to re-lock my bootloader and wipe the device.
This guide assumes you have the SDK Platform Tools installed and working, along with USB drivers for your device (if needed), and have your full update zip which you've already extracted the payload.bin from, and then dumped the images using payload dumper. If you haven't done any of these things yet, there are plenty of other guides out there on how to do them.
Steps:
1. Reboot your device to the bootloader (power off, then hold volume up + power) and connect it to USB.
2. The following command will wipe your device. I found this to be necessary to recover my OnePlus 9:
Code:
fastboot -w
3. Now flash the following files:
Code:
fastboot flash boot boot.img
fastboot flash cpucp cpucp.img
fastboot flash dtbo dtbo.img
fastboot flash modem modem.img
fastboot flash oplusstanvbk oplusstanvbk.img
fastboot flash oplus_sec oplus_sec.img
fastboot flash qweslicstore qweslicstore.img
fastboot flash shrm shrm.img
fastboot flash splash splash.img
fastboot flash vbmeta vbmeta.img
fastboot flash vbmeta_vendor vbmeta_vendor.img
fastboot flash vbmeta_system vbmeta_system.img
fastboot flash vendor_boot vendor_boot.img
fastboot flash vm-bootsys vm-bootsys.img
4. Now reboot into userspace fastboot, aka fastbootd. If you don't do this, the remaining files cannot be flashed:
Code:
fastboot reboot fastboot
5. Flash the remaining files:
Code:
fastboot flash abl abl.img
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash devcfg devcfg.img
fastboot flash dsp dsp.img
fastboot flash featenabler featenabler.img
fastboot flash hyp hyp.img
fastboot flash imagefv imagefv.img
fastboot flash keymaster keymaster.img
fastboot flash multiimgoem multiimgoem.img
fastboot flash qupfw qupfw.img
fastboot flash tz tz.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash xbl xbl.img
fastboot flash xbl_config xbl_config.img
fastboot flash product product.img
fastboot flash system system.img
fastboot flash system_ext system_ext.img
fastboot flash vendor vendor.img
fastboot flash odm odm.img
6. Final reboot:
Code:
fastboot reboot
7. If everything worked your phone should now boot into OxygenOS.
Note:
The files will be flashed to your currently active boot slot. If any of them fail to flash, switch to the other slot and start over from the beginning. I wasn't able to flash odm, product, system, system_ext and vendor to slot a, and had to use slot b instead. To check current slot:
Code:
fastboot getvar current-slot
To switch slots:
Code:
fastboot --set-active=a
or
Code:
fastboot --set-active=b
Use this guide at your own risk. I take no responsibility if you brick your device, set it on fire, or otherwise mess it up as a result of any of the above steps. That being said, it worked for me using 11.2.2.2.LE25AA available from the official OnePlus support website.
If you want, you can do the flashing easily with powershell, rather than running each command one after the other. Here is what I did:
1. Have fastboot.exe in your path, or in the same folder as all your extracted images. Open powershell and navigate to the folder with your boot images. Connect your phone to USB.
2. This will wipe your device! Reboot to the bootloader and run:
Code:
fastboot -w
3. Run:
Code:
gci -filter *.img | where {$_.Name.split('.')[0] -match 'boot|cpucp|dtbo|modem|oplusstanvbk|oplus_sec|qweslicstore|shrm|splash|vbmeta|vbmeta_vendor|vbmeta_system|vendor_boot|vm-bootsys'} | foreach-object { fastboot.exe flash $($_.Name.split('.')[0]) $_.Name }
4. Run:
Code:
fastboot reboot fastboot
5. Run:
Code:
gci -filter *.img | where {$_.Name.split('.')[0] -match 'abl|aop|bluetooth|devcfg|dsp|featenabler|hyp|imagefv|keymaster|multiimgoem|qupfw|tz|uefisecapp|xbl|xbl_config|product|system|system_ext|vendor|odm'} | foreach-object { fastboot.exe flash $($_.Name.split('.')[0]) $_.Name }
6. Run:
Code:
fastboot reboot
7. Proceed to boot normally.
The commands in steps 3 and 5 get a list of all files in the current directory with the .img extension, filter them to the correct ones to flash, and then flash them one after another.
If someone wants, I can probably throw together a script to run the whole process start to finish.
Edit: script attached. I've (unfortunately) had the opportunity to test it and fix all the bugs. So it works. You will need to have fastboot.exe accessible in your system PATH to run it.
Slikkster2k said:
If you want, you can do the flashing easily with powershell, rather than running each command one after the other. Here is what I did:
1. Have fastboot.exe in your path, or in the same folder as all your extracted images. Open powershell and navigate to the folder with your boot images. Connect your phone to USB.
2. Reboot to the bootloader and run:
Code:
fastboot -w
This will wipe your device!
3. Run:
Code:
gci -filter *.img | where {$_.Name.split('.')[0] -match 'boot|cpucp|dtbo|modem|oplusstanvbk|oplus_sec|qweslicstore|shrm|splash|vbmeta|vbmeta_vendor|vbmeta_system|vendor_boot|vm-bootsys'} | foreach-object { fastboot.exe flash $($_.Name.split('.')[0]) $_.Name }
4. Run:
Code:
fastboot reboot fastboot
5. Run:
Code:
gci -filter *.img | where {$_.Name.split('.')[0] -match 'abl|aop|bluetooth|devcfg|dsp|featenabler|hyp|imagefv|keymaster|multiimgoem|qupfw|tz|uefisecapp|xbl|xbl_config|product|system|system_ext|vendor|odm'} | foreach-object { fastboot.exe flash $($_.Name.split('.')[0]) $_.Name }
6. Run:
Code:
fastboot reboot bootloader
7. Proceed to boot normally.
The commands in steps 3 and 5 get a list of all files in the current directory with the .img extension, filter them to the correct ones to flash, and then flash them one after another.
If someone wants, I can probably throw together a script to run the whole process start to finish.
Click to expand...
Click to collapse
That would be helpful indeed. Would this script run on mac as well?
Not unless there's a version of PowerShell for macs (there is for Linux, but I don't know if it's compatible).
@Slikkster2k: I tried your tutorial. At first it did not work...serveral errors occure during copying one file. On the second run I had to change the slot, than it runs through.
But now I am in a boot loop, during starting the oxygen.
While wiping I got this message:
Code:
fastboot: error: Cannot generate image for userdata
Which version of the OS did you use?
I tried to install the actual european rom (11.2.3.3) on my indian device from china but this obviously did not work. Do you have any suggestions for me?
AxelM said:
@Slikkster2k: I tried your tutorial. At first it did not work...serveral errors occure during copying one file. On the second run I had to change the slot, than it runs through.
But now I am in a boot loop, during starting the oxygen.
While wiping I got this message:
Code:
fastboot: error: Cannot generate image for userdata
Which version of the OS did you use?
I tried to install the actual european rom (11.2.3.3) on my indian device from china but this obviously did not work. Do you have any suggestions for me?
Click to expand...
Click to collapse
I used 11.2.2.2.LE25AA as I said in the original post (this is the global variant, which matches my device). I am not sure if this works for cross-flashing, or if it's possible to cross-flash an Indian phone to EU. Have you tried restoring the Indian ROM? Does that work?
You're getting an actual boot loop? The error I was getting (and the reason I had to restore) was the phone booting to the bootloader or fastbootd (depending on the slot I tried) instead of Oxygen, because it couldn't mount the user partition due to encryption. In fastbootd an error was reported (I forget the exact one) which made me suspect it was a partition mounting issue. At no point was my phone actually boot looping, even during partial/failed flashes.
I've never encountered the error with fastboot -w, but I only did that on my phone once. From some searching online, it can be caused by an old version of the platform tools, so did you download the latest version?
@Slikkster2k: First of all, thank you for providing help
In deed, what worked was the indian first version. This i could flash and from there on everything works. Up to OS and than installing the latest european os. Now everything ist fine...
The error while whiping did not occure while using the indian version...so no clue why...
But now it works for me, thank you!
AxelM said:
@Slikkster2k: First of all, thank you for providing help
In deed, what worked was the indian first version. This i could flash and from there on everything works. Up to OS and than installing the latest european os. Now everything ist fine...
The error while whiping did not occure while using the indian version...so no clue why...
But now it works for me, thank you!
Click to expand...
Click to collapse
Glad to hear you got it working!
PowerShell script added to second post. Totally untested, but I tried to make it as idiot proof as possible.
Slikkster2k said:
This guide assumes you have the SDK Platform Tools installed and working, along with USB drivers for your device (if needed), and have your full update zip which you've already extracted the payload.bin from, and then dumped the images using payload dumper. If you haven't done any of these things yet, there are plenty of other guides out there on how to do them.
Steps:
1. Reboot your device to the bootloader (power off, hold volume up + power) and connect it to USB.
2. The following command will wipe your device. I found this to be necessary to recover my OnePlus 9:
Code:
fastboot -w
3. Now flash the following files:
Code:
fastboot flash boot boot.img
fastboot flash cpucp cpucp.img
fastboot flash dtbo dtbo.img
fastboot flash modem modem.img
fastboot flash oplusstanvbk oplusstanvbk.img
fastboot flash oplus_sec oplus_sec.img
fastboot flash qweslicstore qweslicstore.img
fastboot flash shrm shrm.img
fastboot flash splash splash.img
fastboot flash vbmeta vbmeta.img
fastboot flash vbmeta_vendor vbmeta_vendor.img
fastboot flash vbmeta_system vbmeta_system.img
fastboot flash vendor_boot vendor_boot.img
fastboot flash vm-bootsys vm-bootsys.img
4. Now reboot into userspace fastboot, aka fastbootd. If you don't do this, the remaining files cannot be flashed:
Code:
fastboot reboot fastboot
5. Flash the remaining files:
Code:
fastboot flash abl abl.img
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash devcfg devcfg.img
fastboot flash dsp dsp.img
fastboot flash featenabler featenabler.img
fastboot flash hyp hyp.img
fastboot flash imagefv imagefv.img
fastboot flash keymaster keymaster.img
fastboot flash multiimgoem multiimgoem.img
fastboot flash qupfw qupfw.img
fastboot flash tz tz.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash xbl xbl.img
fastboot flash xbl_config xbl_config.img
fastboot flash product product.img
fastboot flash system system.img
fastboot flash system_ext system_ext.img
fastboot flash vendor vendor.img
fastboot flash odm odm.img
6. Reboot back into the bootloader:
Code:
fastboot reboot bootloader
7. You should now be able to continue booting normally by pressing the power button.
Note:
The files will be flashed to your currently active boot slot. If any of them fail to flash, switch to the other slot and start over from the beginning. I wasn't able to flash odm, product, system, system_ext and vendor to slot a, and had to use slot b instead. To switch slots:
Code:
fastboot --set-active=a
or
Code:
fastboot --set-active=b
Use this guide at your own risk. I take no responsibility if you brick your device, set it on fire, or otherwise mess it up as a result of any of the above steps. That being said, it worked for me using 11.2.2.2.LE25AA available from the official OnePlus support website.
Click to expand...
Click to collapse
My phone has been weird for a week or so occasionally freezing up and saying system ui has crashed or something so I followed these instructions last night to completely wipe and reset everything (after backing up). It worked perfectly!
My only suggestion would be for step 7 to be:
fastboot reboot
Since we're already using fastboot it's just quicker and less fiddly than using the power button
toyanucci said:
That would be helpful indeed. Would this script run on mac as well?
Click to expand...
Click to collapse
Windows offered now to add to MAC - https://support.apple.com/en-us/HT201468
toyanucci said:
My phone has been weird for a week or so occasionally freezing up and saying system ui has crashed or something so I followed these instructions last night to completely wipe and reset everything (after backing up). It worked perfectly!
My only suggestion would be for step 7 to be:
fastboot reboot
Since we're already using fastboot it's just quicker and less fiddly than using the power button
Click to expand...
Click to collapse
Thanks, updated OP.
ok i kind of bricked my phone using this and i need a little help PLEASE?
Ok i tried the fist 2 steps 1. fastboot -w than the first list of commands using cmd with admin rights it worked...i think but it did load everything without issues...now i go to do the "fastboot reboot fastboot"
and now my phone is stuck on a black screen with nothing and i just hear the chime windows makes when you disconnect and reconnect a device..... and in the Device manager this comes up for 10 seconds than goes away for 5 than comes back NON STOP
i cant adb i cant do anything please help !
I'm not sure if this will help you, but I had a lot of issues initially running this. First off you need to use the Oneplus drivers, I don't think the qualcom driver will work the same way. I could be wrong, but that's what I did. Secondly, you need to force install the driver because Windows doesn't like it.
Here are the steps I took.
1. Uninstall any old drivers.
2. Install the newest Oneplus Drivers from here https://oneplususbdrivers.com/
3. Extract the zip file and run the installer like normal
4. Once the installer finishes, you'll need to reboot your machine and bring up the Startup settings (hold down shift and reboot (keep holding down shift until you get a screen with options)) Then click advanced and startup settings and hit restart after that. Once the machines starts up, on the first boot you will have a bunch of options. Choose option 7 "disabling driver signature enforcement" mode.
5. Once Windows launches and you login, go back into the device manager and follow these steps:
right click the device --> update driver
Browse my computer for drivers
Let me pick from a list of available drivers on my computer
Show all Devices --> Next
Have Disk (Button)
Navigate to where you installed Oneplus drivers (Default: C:\Program Files (x86)\OnePlus USB Drivers)
Select "OnePlus_android_winusb.inf"
Select "Oneplus Android Bootloader Interface" and then just hit next/OK until it installs.
You might need to reboot after doing the above, but this worked for me.
----------------------------------------
The above should get your drivers working properly in all modes (adb, fastbootd, bootloader, normal)
One other issue that I ran into when I was using the powershell script was that I was seeing intermittent errors. After trial and error I realized that Windows was picking up a different version of fastboot. I was initially using the minimal adb/fastboot files, but if you compare those to the ones listed in the first post in the "SDK Platform Tools", they are very different from each other, so you need to make sure you use the SDK Platform Tools version. The minimal ADB/Fastboot version will NOT work.
After I got those 2 things ironed out, the powershell script ran without a hiccup and my phone is stock and booting without an issue.
I know I'm late to respond to this thread, but I hope someone finds this information helpful!
Mine keeps trying this and it isn't running and or rebooting into Fastbootd when the script is ran. Should I just try and invoke this manually? I've tried that as well an I'm seeming to get errors left and right with no resolve.
I'd say try it manually and see where the errors happen. Does it boot into fastbootd at all?
Good work
toyanucci said:
I'd say try it manually and see where the errors happen. Does it boot into fastbootd at all?
Click to expand...
Click to collapse
Actually, I ended up making my phone hard bricked to the point where it doesn’t even turn on at this point. I’m just going to send it in for repair, which is nothing short of being due to my stupidity.
ilikepie___ said:
Actually, I ended up making my phone hard bricked to the point where it doesn’t even turn on at this point. I’m just going to send it in for repair, which is nothing short of being due to my stupidity.
Click to expand...
Click to collapse
It's probably stuck in edl mode. Nothing on the screen, no vibration or anything but it shows up in device manager when connected to a computer?
Try the man tool mentioned Here that worked for me.
toyanucci said:
It's probably stuck in edl mode. Nothing on the screen, no vibration or anything but it shows up in device manager when connected to a computer?
Try the man tool mentioned Here that worked for me.
Click to expand...
Click to collapse
I’ll give it a shot, yeah it doesn’t do anything. Can’t see a display or anything on the screen.