Related
Hello. I have got very annoying problem. I'm using Kyrillos 9.4.
Sometimes (twice a week) my g3 get freeze, and I can't unlock it, because screen don't light on. I must get battery off and on and after battery remove phone works as new.
I have this freeze on every kernel (G3MOD oc, non-oc, kyroarokernel)
Is there any fix for this issue?
This is annoying in the long run.
Do you have this problem too? Or my g3 has got defect?
PS. When I'm using stock, Samsung rom this issue does not exist.
Do u undervolt?
Cheers
Sent from my i9003 powered by Poseidon's Rom/Dxkp9 Junior + UC kernel
No. (10 characters)
mosak said:
No. (10 characters)
Click to expand...
Click to collapse
Then I'm not very sure. The only causes I know of freezes is undervolting and overclocking. Since u do neither, I don't know. I would wipe cache and dalvik cache, if doesn't work factory reset, if doesn't work reflash. Are u sure u tested on non-oc kernel?
Cheers
Sent from my i9003 powered by Poseidon's Rom/Dxkp9 Junior + UC kernel
Yes, I'm sure. Now i have got Non-OC kernel (G3MOD 2.3 non-oc). In set CPU I can set max frequency 667Mhz.
But on non-oc i have got this issue less frequently than on oc.
Maybe 1-2 times at month.
Have you ever got same frezze like mine?
Thank for help
Maybe once or twice on oc. I'm nt sure wad is causing your problem, but if its very little freezes then maybe you can live with it?
Cheers
Sent from my i9003 powered by Poseidon's Rom/Dxkp9 Junior + UC kernel
mosak said:
Hello. I have got very annoying problem. I'm using Kyrillos 9.4.
Sometimes (twice a week) my g3 get freeze, and I can't unlock it, because screen don't light on. I must get battery off and on and after battery remove phone works as new.
I have this freeze on every kernel (G3MOD oc, non-oc, kyroarokernel)
Is there any fix for this issue?
This is annoying in the long run.
Do you have this problem too? Or my g3 has got defect?
PS. When I'm using stock, Samsung rom this issue does not exist.
Click to expand...
Click to collapse
try flash the kernel with odin, using tar file. And next wipe data
Ok. I flashed kernel via Odin and now it's ok.
I post new reply after 100h uptime (or first freeze )
I have been having issues getting my TF101 to overclock in ICS. I have tried Codename Android, CM9, TeamEOS, and Revolver, and ALL of them I could not overclock in. I have tried SetCPU, No-Frills, and (if applicable) the built in frequency control. They all show that the maximum frequency is 1000MHz. I have no clue what is going wrong here. They all were able to gain Superuser, so that isn't the problem. Any and all help would be highly appreciated. I just have no clue what I could be doing wrong.
stompysan said:
I have been having issues getting my TF101 to overclock in ICS. I have tried Codename Android, CM9, TeamEOS, and Revolver, and ALL of them I could not overclock in. I have tried SetCPU, No-Frills, and (if applicable) the built in frequency control. They all show that the maximum frequency is 1000MHz. I have no clue what is going wrong here. They all were able to gain Superuser, so that isn't the problem. Any and all help would be highly appreciated. I just have no clue what I could be doing wrong.
Click to expand...
Click to collapse
Antutu CPUMaster Free works for me on Revolver4_1.3.1 and Blades_meh kernel. You have to manually go into it after installing a OC kernel and set the min and max frequencies and choose a governor and there's a checkbox to tell it to set these at boot. After that it works all day everyday for me up to 1680MHz and deep sleep works, too.
sidneyk said:
Antutu CPUMaster Free works for me on Revolver4_1.3.1 and Blades_meh kernel. You have to manually go into it after installing a OC kernel and set the min and max frequencies and choose a governor and there's a checkbox to tell it to set these at boot. After that it works all day everyday for me up to 1680MHz and deep sleep works, too.
Click to expand...
Click to collapse
Just tried Antutu CPU Master. Same issues. It says that my max frequency is 1000MHz.
Have you manually loaded a new kernel to replace the stock one? Setcpu and the like only modify settings that a kernel exposes, and the default kernel does not allow anything higher then 1000.
Tekfrog said:
Have you manually loaded a new kernel to replace the stock one? Setcpu and the like only modify settings that a kernel exposes, and the default kernel does not allow anything higher then 1000.
Click to expand...
Click to collapse
Yes. After doing so, I also go into my settings and clear the cache and data from SetCPU, so I could set it up again. Still, I am getting max 1000MHz.
stompysan said:
Yes. After doing so, I also go into my settings and clear the cache and data from SetCPU, so I could set it up again. Still, I am getting max 1000MHz.
Click to expand...
Click to collapse
Which kernel are you running now?
Tekfrog said:
Which kernel are you running now?
Click to expand...
Click to collapse
Thanks for trying to help, but I have found my problem. My recovery was still borked from when I tried flashing the official one in Rom Manager. Wiped my recovery, installed the roach recovery, reflashed all of my files, and now I am good to go. I feel like a derp now. LOL
Same issue w/ OC...but wipe recovery?
Your issue sounds exactly like the one I am currently having.
I would like to try your fix...but I am not understanding how the "wipe recovery" process goes. Would you mind please explaining that in more detail? Im pretty sure it IS NOT as simple as just doing a complete cache/data wipe then flashing the recovery over itself is it?
I am:
ViperMOD Prime rooted
ClockworkRecoveryMOD installed (but I think I may have fubar'd it doing the same thing you did trying to recover stock recovery)
FROZN 1.0.9 rom w/ included Guevor kernel and NoFrills CPU app
...but none of the CPU apps will let me OC...wether I flash the kernel seperate from the ROM or use the one included w/ the ROM.
Hope you can help me.
UPDATE: apparently this inability to OC the kernel in any way is happening to those of us experiencing the CWM bootloop issue...so since the loader goes immediately to CWM it never runs the flashed kernel.
So in these forums is a thread to fix the CWM bootloop and if you follow the instructions carefully, you fix the bootloop and thus allowing the flashed kernels a chance to actually install. I chose the Roach method which you can install the code using Terminal Emulator pretty intuitively. I didnt choose the other method because I didnt want to mess w/ setting up an ADB terminal on my PC, which seemed MUCH more difficult.
So...now FINALLY
ViperMOD Prime rooted
ClockworkMOD Touch Recovery 5.8.8
FROZN 1.0.9 ROM (w/ built-in Guevor kernel @ 1.2 default) and am OCd @ 1.54 (np's at all so far, lightning fast, havent even tried 1.6 or 1.7).
Only issue so far is File Manager app crashes on startup...which isnt good because now the other file manager app I tried doesnt see my ext_SDcard...the stock File Manager did.
I've tried using both tastyMEH and Blades using Revolver, CM9 and Android HD, and the stock ICS ROM, using Set CPU and ROM Toolbox pro to try and overclock. I've flashed the ROM first and then the Kernel, and the Kernel and then the ROM. Nothing I've done thus far has enabled me to set the CPU sliders past 1000 mhz. I know people are running these combos and getting 1.6-1.8 clocks. What am I screwing up? I'm using Clockwork Mod recovery to flash. I couldn't even get CM9 to boot.
Thanks so much in advance
Teh Wuss
WU55 said:
I've tried using both tastyMEH and Blades using Revolver, CM9 and Android HD, and the stock ICS ROM, using Set CPU and ROM Toolbox pro to try and overclock. I've flashed the ROM first and then the Kernel, and the Kernel and then the ROM. Nothing I've done thus far has enabled me to set the CPU sliders past 1000 mhz. I know people are running these combos and getting 1.6-1.8 clocks. What am I screwing up? I'm using Clockwork Mod recovery to flash. I couldn't even get CM9 to boot.
Thanks so much in advance
Teh Wuss
Click to expand...
Click to collapse
Please see above solution...I know it seems unrelated but it is the fix for both CWM bootloop AND being able to accept and install a flashed kernel.
If you need additional help, please ask. I am willing to share my solution in more detail to help others out.
WU55 said:
I've tried using both tastyMEH and Blades using Revolver, CM9 and Android HD, and the stock ICS ROM, using Set CPU and ROM Toolbox pro to try and overclock. I've flashed the ROM first and then the Kernel, and the Kernel and then the ROM. Nothing I've done thus far has enabled me to set the CPU sliders past 1000 mhz. I know people are running these combos and getting 1.6-1.8 clocks. What am I screwing up? I'm using Clockwork Mod recovery to flash. I couldn't even get CM9 to boot.
Thanks so much in advance
Teh Wuss
Click to expand...
Click to collapse
When you flash the kernel go to the about section in android and make sure the flash was actually successful.
fwbflash said:
Please see above solution...I know it seems unrelated but it is the fix for both CWM bootloop AND being able to accept and install a flashed kernel.
If you need additional help, please ask. I am willing to share my solution in more detail to help others out.
Click to expand...
Click to collapse
Thanks, this may be a step in the right direction. However I've tried 3 times now to flash the 5.8 touch to no avail. Everytime I reboot I end up with standard 5.5.0.4. I tried flashing with CWM. What am I doing wrong? If it helps ever since I flashed CWM, if the tablet retboots for any reason it automatically boots into CWM, and I have to cold boot into Android manually using the power and volume rocker.
Thanks again-
Teh Wuss
WU55 said:
Thanks, this may be a step in the right direction. However I've tried 3 times now to flash the 5.8 touch to no avail. Everytime I reboot I end up with standard 5.5.0.4. I tried flashing with CWM. What am I doing wrong? If it helps ever since I flashed CWM, if the tablet retboots for any reason it automatically boots into CWM, and I have to cold boot into Android manually using the power and volume rocker.
Thanks again-
Teh Wuss
Click to expand...
Click to collapse
Because your version of CWM is bad. You need to read this thread: http://forum.xda-developers.com/showthread.php?t=1530337
It's on the front page of general discussion, how did you even not see it yet.
horndroid said:
Because your version of CWM is bad. You need to read this thread: http://forum.xda-developers.com/showthread.php?t=1530337
It's on the front page of general discussion, how did you even not see it yet.
Click to expand...
Click to collapse
Thanks, this was it, I didn't see it, because I was a noob and didn't look for it.
Hello,
I have an HTC One S with ViperS 2.0.0 rom. Few days ago, I installed Elemental-S-JB-v2.1 kernel and choosed an 1.7 overclock for the CPU. After flashing the kernel zip and update boot.img via fastboot flash boot command, I booted my phone. All seems to work but when I controlled my overclock with kernel tuner.
So I noticed that the second core was at stock frequency instead of 1.7 GHz like the first core.
Some one could me explain why ?
Just set the second core's maximum clock rate to 1.7Ghz. The Kernel allows you to do this now.
KACE321 said:
Just set the second core's maximum clock rate to 1.7Ghz. The Kernel allows you to do this now.
Click to expand...
Click to collapse
Effectively, I notice that I could with kernel tuner manualy set the frequency of the second core. But I wonder why the overclock frequency choosed during installation of the kernel doesn't affect the second core.
For me, it's perhaps a mistake, it shows that the overclok frequency is not well applied by the installer or there with an problem with frequency policy with this kernel.
Nobody can give me an answer.
I noticed too that the CPU Governor between the first core and the second is different.
Someone knows why ?
That is normal ?
Someone with a stock Rom could check with kernel tuner if the CPU gouvernors are the same ?
Stuff like that has always been picky and not much you can do about it.
Okay, I am practically a beginner with this. Also, I did my flashing/rooting a month back, so I might muddle some of the facts.
The thing is, at first I had this problem : Thread
I had a stock Froyo on my phone and I tried following the steps of this thread : http://forum.xda-developers.com/show....php?t=1894737
The first mistake I did, was I flashed XXKPQ directly by mistake instead of XXKPE, which I noticed while I was in the middle of doing it.
The phone was working properly on the GB rom. After that I rooted it, following the guide using a cf root of XXKPQ.
Now, I didn't know if there was prerequisite for it or not, but I flashed the custom rom of http://forum.xda-developers.com/show....php?t=2300693
The first problem I saw was that while installing it from the sdcard, for a long time, the screen was blank. I left it thinking that it was part of it, but since it persisted, I rebooted it. The phone opened properly and after that I installed the gapps later through recovery mode.
The first major problem I saw was that the phone after screen locking, it used to shut down automatically. After looking through solutions, where none were working, I tried flashing to stock rom via odin (stock rom : http://forum.xda-developers.com/show...php?p=16107097)
After that though, whenever I open the phone, it just stucks at the samsung logo screen and doesn't go further.
Also, when in download mode, I tried it attaching to Odin but "USB device not recognized" comes all the time.
I don't know what to do.. I know I must have made loads of huge mistakes and I should have done everything, being properly informed, but now I really need a solution..
Click to expand...
Click to collapse
So, in the end, I remember re-flashing it to DDLF2 and then doing the XXKPE + XXKPQ + BAM Kernel + CWM 10.1.
But there is a SOD. After a while, it suddenly switches off.
Can anyone tell me what to do, to solve this problem and if someone has patience, please help me step by step? In the end, I want to have a JB custom rom in my phone. I just want to get there, without having any problems.
Any help please, removing this SOD?
tyson123g said:
Okay, I am practically a beginner with this. Also, I did my flashing/rooting a month back, so I might muddle some of the facts.
The thing is, at first I had this problem : Thread
So, in the end, I remember re-flashing it to DDLF2 and then doing the XXKPE + XXKPQ + BAM Kernel + CWM 10.1.
But there is a SOD. After a while, it suddenly switches off.
Can anyone tell me what to do, to solve this problem and if someone has patience, please help me step by step? In the end, I want to have a JB custom rom in my phone. I just want to get there, without having any problems.
Any help please, removing this SOD?
Click to expand...
Click to collapse
Flash It Again From First In Download Mode And Root It And Go To An Custom Rom.
karthik gowtham said:
Flash It Again From First In Download Mode And Root It And Go To An Custom Rom.
Click to expand...
Click to collapse
Do you mean the same process I used? DDLF2 -> XXKPE + XXKPQ -> BAM Kernel + CWM 10.1
Or am I missing something or adding something in the mix, which I shouldn't?
tyson123g said:
Do you mean the same process I used? DDLF2 -> XXKPE + XXKPQ -> BAM Kernel + CWM 10.1
Or am I missing something or adding something in the mix, which I shouldn't?
Click to expand...
Click to collapse
Why Do You Got To XXKPE From DDLF2 ,All I Was Trying To Say Was
XXKPE--->DDMF1--->CF-Root or Custom Kernels--->CM10.1 or Any Other Rom.
Thanks, the above way helped.
I installed using the process you mentioned, installing the CF Root for DDMF1 and then finally installing REMICS latest one (5.x).
But it is still a bit slow. So, I was thinking of overclocking it.
Can you tell me, which kernel should I flash?
tyson123g said:
Thanks, the above way helped.
I installed using the process you mentioned, installing the CF Root for DDMF1 and then finally installing REMICS latest one (5.x).
But it is still a bit slow. So, I was thinking of overclocking it.
Can you tell me, which kernel should I flash?
Click to expand...
Click to collapse
REMICS v6 now is out (smoother and more stable)
kernel 3.0.8 by dhiru1602 does not support OC but you can change the governor to ondemand or performance (performance>>processor>>CPU governor) and the I/O scheduler to deadline (performance>>I/O scheduler) but first you have to enable the developper options (7 hits on the Build number).
Hit thanks "button" if i helped you!
regards
Thanks for the suggestion, but I think I am missing something here.
I tried searching for the kernel, but I just can't seem to find it.
Am I doing something wrong?
Edit : Okay, so I searched and found out that most of the newer ROMs have it installed in itself, is that right?
But when I installed the REMICS 5.8 and tried using the no frills CPU app, I just don't see any option beyond 1 GHz.
tyson123g said:
Thanks for the suggestion, but I think I am missing something here.
I tried searching for the kernel, but I just can't seem to find it.
Am I doing something wrong?
Edit : Okay, so I searched and found out that most of the newer ROMs have it installed in itself, is that right?
But when I installed the REMICS 5.8 and tried using the no frills CPU app, I just don't see any option beyond 1 GHz.
Click to expand...
Click to collapse
Yes, because as i know kernel 3.0.8 by dhiru1602 which is the default (preinstalled) kernel of CM10.1 (Jelly bean 4.2.2) (REMICS 5.x and 6 and the newer jelly bean roms are based on CM10.1 by dhiru1602) does not support OC and you won't find other kernel for CM10.1 better than dhiru1602 kernel (it's only my idea).
I think dhiru1602 didn't implement OC in his kernel for reasons of stability and battery backup...and you don't have to use no frills CPU app anymore, just 7 hits on the Build number (About the phone >> Build number) will enable the "developper options" and "performance" (in "performance" you can change the CPU governor and I/O scheduler).
And don't use REMICS 5.8, REMICS 6 is better because many bugs were fixed!!!
Hit thanks "button" if i helped you!
regards
Thanks for the reply.
Just had one little question..
Even in the performance options, as the same in the no CPU app, my maximum frequency is always 1000 MHz?
Is it always like that, or should I go beyond it as well? I thought I was overclocking so I expected an option beyond it..
tyson123g said:
Thanks for the reply.
Just had one little question..
Even in the performance options, as the same in the no CPU app, my maximum frequency is always 1000 MHz?
Is it always like that, or should I go beyond it as well? I thought I was overclocking so I expected an option beyond it..
Click to expand...
Click to collapse
in CM10.1 kernel overclocking is not there for some stability issues... overclocking is possible but do it at your own risk
tyson123g said:
Thanks for the reply.
Just had one little question..
Even in the performance options, as the same in the no CPU app, my maximum frequency is always 1000 MHz?
Is it always like that, or should I go beyond it as well? I thought I was overclocking so I expected an option beyond it..
Click to expand...
Click to collapse
You really don't need to OC your CPU....if you are facing some lags in CM, this maybe because you didn't wipe data before install CM.
Usually I downclock my cpu to 600MHz and set the governor to conservative to save battery without facing lags...so really CM10.1 A8 is not lagging!!!
Okay. I have to install REMICS 6 anyway. I will try again. Hopefully this time, it is quick.
Well, I changed my mind and went with CM 10.1 A8. It is fast and good.
But for some reason, my phone is rebooting by itself.
Hi Guys....I'm posting here because I don't have the privileges to post on the official Trinity Kernel thread. I just flashed the kernel this morning and while I'm more than satisfied with the performance I'm a little worried that it simply won't let me choose the CPU frequency. It simply maxes out at 3.14 Ghz ...which is way more than I actually need or want...and whenever I try to go to a more safe 2.3- 2.4 Ghz it simply won't change....tried flashing older versions but it just the same. Is it safe for me to keep it like this or should I try another kernel? Thanks
Catani said:
Hi Guys....I'm posting here because I don't have the privileges to post on the official Trinity Kernel thread. I just flashed the kernel this morning and while I'm more than satisfied with the performance I'm a little worried that it simply won't let me choose the CPU frequency. It simply maxes out at 3.14 Ghz ...which is way more than I actually need or want...and whenever I try to go to a more safe 2.3- 2.4 Ghz it simply won't change....tried flashing older versions but it just the same. Is it safe for me to keep it like this or should I try another kernel? Thanks
Click to expand...
Click to collapse
what do you mean it wont let you chose cpu frequency? by default, trinity maxes at 2260mhz btw, not 3014mhz. you can set it manually to 3014mhz, but chances are that your phone will not be able to run at 3014mhz, very few can. anyways, you need to install a cpu control app to adjust your cpu speed, i use the trinity kernel toolbox, but there are others around.
Catani said:
Hi Guys....I'm posting here because I don't have the privileges to post on the official Trinity Kernel thread. I just flashed the kernel this morning and while I'm more than satisfied with the performance I'm a little worried that it simply won't let me choose the CPU frequency. It simply maxes out at 3.14 Ghz ...which is way more than I actually need or want...and whenever I try to go to a more safe 2.3- 2.4 Ghz it simply won't change....tried flashing older versions but it just the same. Is it safe for me to keep it like this or should I try another kernel? Thanks
Click to expand...
Click to collapse
When flashed, some kernels break root access. Flash the latest supersu (http://forum.xda-developers.com/showthread.php?t=1538053), and then you'll be able to use an app like TKT or trickster to adjust CPU. I use Trinity mostly, and sometimes have this issue if I forget to flash supersu,
also you need to have busybox installed if you are already using a cpu control app. the cpu control app would need busybox to work properly.
simms22 said:
what do you mean it wont let you chose cpu frequency? by default, trinity maxes at 2260mhz btw, not 3014mhz. you can set it manually to 3014mhz, but chances are that your phone will not be able to run at 3014mhz, very few can. anyways, you need to install a cpu control app to adjust your cpu speed, i use the trinity kernel toolbox, but there are others around.
Click to expand...
Click to collapse
Hi. Thanks for your quick reply. What I meant to say is that I use the trinity kernel toolbox but whatever cpu speed I choose it always goes back to 3014mhz...I even tried underclocking...just for the sake of it but nothing...I tried to go default with 2260 mhz but I still get 3014mhz in antutu and geekbench 3. Did a benchmark with antutu and I get 32460 when it should be around 24000. I don't know if I should be worried or glad. While my N5 isn't getting any hotter my past ock experiences tell me that I shouldn't push it. Am I doing something wrong?
Catani said:
Hi. Thanks for your quick reply. What I meant to say is that I use the trinity kernel toolbox but whatever cpu speed I choose it always goes back to 3014mhz...I even tried underclocking...just for the sake of it but nothing...I tried to go default with 2260 mhz but I still get 3014mhz in antutu and geekbench 3. Did a benchmark with antutu and I get 32460 when it should be around 24000. I don't know if I should be worried or glad. While my N5 isn't getting any hotter my past ock experiences tell me that I shouldn't push it. Am I doing something wrong?
Click to expand...
Click to collapse
Antutu and Geekbench 3 show you the max frequency that your phone can go up to on your Nexus 5. If the kernel is overclockable, then these benchmarks will show you the max frequency, in Trinity kernel's case, 3.1Ghz. If everything looks right in the Trinity Toolbox app, then you're good to go. Trinity doesn't come overclocked by default.
Catani said:
Hi. Thanks for your quick reply. What I meant to say is that I use the trinity kernel toolbox but whatever cpu speed I choose it always goes back to 3014mhz...I even tried underclocking...just for the sake of it but nothing...I tried to go default with 2260 mhz but I still get 3014mhz in antutu and geekbench 3. Did a benchmark with antutu and I get 32460 when it should be around 24000. I don't know if I should be worried or glad. While my N5 isn't getting any hotter my past ock experiences tell me that I shouldn't push it. Am I doing something wrong?
Click to expand...
Click to collapse
well, you are not running your phone at 3014mhz. a 32000+ in antutu is average for 2260mhz considering you are running the dalvik/bionic patches(your rom probably includes them. i getvabove 40000 at 2.5ghz, cant imagine what it woukd becat 3014mhz! btw, what rom are you running? anyways, it sounds to me as you dont have busybox installed, tkt needs it to work properly. go to the play store, find the busybox app by stericson, install it, open it, let it do its thing, then install it and reboot. that should get tkt working properly. like i said, the default trinity top cpu speed is 2260mhz and no higher.
Paradelle said:
When flashed, some kernels break root access. Flash the latest supersu (http://forum.xda-developers.com/showthread.php?t=1538053), and then you'll be able to use an app like TKT or trickster to adjust CPU. I use Trinity mostly, and sometimes have this issue if I forget to flash supersu,
Click to expand...
Click to collapse
Thanks....seems I lost root access. Re-flashed SuperSU and now everything's working great. Thanks guys for all your quick help. Have a nice one
Catani said:
Thanks....seems I lost root access. Re-flashed SuperSU and now everything's working great. Thanks guys for all your quick help. Have a nice one
Click to expand...
Click to collapse
awesome!
i flash supersu every single time i update my rom, rastakat, because it doesnt include su, and has to be flashed every time.