Hey all,
I have an unrooted Asus Eee Pad Transformer, and I was wondering if anyone could tell me if it is possible to tether the internet from my laptop to my Transformer.
I've plugged it into my laptop, and clicked tether, but do not seem to get any internet connection. Is anyone able to help?
Thanks
Rob
It is possible but you need additional software on your laptop or you need to enable ICS (Internet connection sharing) which often has mixed results.
It also depends on how your laptop is connecting to the internet. If your laptop has a wired connection to the net then your wifi will offer the hotspot connection for your other wireless devices such as the TF'er. I've used Connectify before which worked well although I did need to manually start the connection after each reboot even though it was in the startup programs.
Think I've decided it's my university internet connection. I have a wired connection, but unable to make a wifi hotspot as I'm only allowed one I.P address blah blah, so complete and utter ball ache if you ask. May give them a ring!
I'm in the same situation as you are. No wifi and only one IP.
Use Connectify on laptop. Works for me. No prolem with 1 IP becouse it will make it's own subnet.
Other option is to use USB-rj45 dongle. Had been explaned somewhere on this forum.
Why not use a WiFi router and mirror the IP address if you are only going to use one at a time.
Related
I need some help, as I'm kinda clueless with networking. I have an Ubuntu desktop connected to the same monitor my 360 is. I can connect to xbl a few different ways.
1. With the d-link wireless gaming adapter, set to adhoc mode, connected to my wifi tether.
2. USB/wifi tethering the desktop to my phone and sharing the internet connection with the Ethernet port where my Xbox is plugged in.
I've used, wifi tether for root users, barnacle (which supposedly allows port forwarding), built in USB and wifi tether (I'm on cm7 nightly with an HTC glacier)
I've managed to connect, but NAT is set to strict on all. Does anybody know how to change this? I don't know if there's a way to change this within the build.prop, or some other file?
Any help or advice would be much appreciated. I just have no other internet connection.
#AngelFace#
/b/rotherJudas said:
I need some help, as I'm kinda clueless with networking. I have an Ubuntu desktop connected to the same monitor my 360 is. I can connect to xbl a few different ways.
1. With the d-link wireless gaming adapter, set to adhoc mode, connected to my wifi tether.
2. USB/wifi tethering the desktop to my phone and sharing the internet connection with the Ethernet port where my Xbox is plugged in.
I've used, wifi tether for root users, barnacle (which supposedly allows port forwarding), built in USB and wifi tether (I'm on cm7 nightly with an HTC glacier)
I've managed to connect, but NAT is set to strict on all. Does anybody know how to change this? I don't know if there's a way to change this within the build.prop, or some other file?
Any help or advice would be much appreciated. I just have no other internet connection.
#AngelFace#
Click to expand...
Click to collapse
The lack of response really blows. I have the same exact issue and I cant fathom there not being a way around it . I'll keep looking and please let me know if you stumble upon something that works
The "nat type strict" we see on xbox live, from reading around allot deals with the bandwidth(speed) of your internet. If you use fast wifi, your nat type will be ok, but if someone goes on your wifi an use the internet, it's slower. The internet speeds we get from the cell towers is no where fast enough to change it.
If I helped, give thanks, if you please.
........Death before dishonor........
Team inferno
Leader
I tried to follow this tutorial to use a CradlePoint CTR350 router with the Sensation
http://www.cradlepoint.com/about/blog/an-android-powered-cradlepoint-router
I do not see the "Mobile Broadband Connect" USB connection mode. I did see a USB Tether option, which asked me Mac of PC and I figured the router would be more like a PC and I chose PC. The phone would not share its internet connection with the router.
Has anyone been able to use a Sensation with a CradlePoint router, and if so, which router and what settings did you do on the phone?
Thanks
Any comments?
Thanks in advance.
I really would like to be able to connect the Sensation to a Cradlepoint router so it can be a backup Internet source if my wireline Internet service is down. Any ideas on getting Sensation to work with CradlePoint?
tk_xda said:
I really would like to be able to connect the Sensation to a Cradlepoint router so it can be a backup Internet source if my wireline Internet service is down. Any ideas on getting Sensation to work with CradlePoint?
Click to expand...
Click to collapse
I had a quick look at the web site you gave. If I understand it, it's a USB -> WIFI router. Such that the Cradlepoint WIFI routes via USB and 3G (phone) to the Internet.
Assuming that's the case I can't see anything in particular why it shouldn't work.
Can you use USB tethering to connect a single PC to the Internet via USB/3G ? (If this works and my assumptions are correct the phone is working fine).
Do you need to configure the Cradlepoint device in any way ?
In the absence of this, the phone can act as a WiFI hotspot, does this not give you enough connectivity to the Internet?
gol_n_dal said:
I had a quick look at the web site you gave. If I understand it, it's a USB -> WIFI router. Such that the Cradlepoint WIFI routes via USB and 3G (phone) to the Internet.
Assuming that's the case I can't see anything in particular why it shouldn't work.
Can you use USB tethering to connect a single PC to the Internet via USB/3G ? (If this works and my assumptions are correct the phone is working fine).
Do you need to configure the Cradlepoint device in any way ?
In the absence of this, the phone can act as a WiFI hotspot, does this not give you enough connectivity to the Internet?
Click to expand...
Click to collapse
I actually have Mac and I often use the wifi tethering. I only tried USB tethering with the Cradlepoint. The first time the phone asked me Mac or PC and I chose PC, thinking Cradlepoint would be similar to PC. I don't know how to get it to ask PC or Mac for USB tethering again. I would like to be able to connect an Ethernet cable to Cradlepoint to get to the Internet. That would be for the scenario my home Internet is down, then I would want to connect my main router WAN to the Ethernet of the cradlepoint and get Internet through the cell phone.
Anyone have any success in using a cradlepoint?
I use need to use my phone to get my laptop online a lot. I had the Epic for two years, and rooted that so I could use the wireless tether. I have not rooted my Q LTE yet. Most of the time I don't care how the connection sets up my IP. However, I do have times when I need my laptop to be online and on a wired network connection simultaneously. When I tried to do that recently using Easy Tether, I kicked my IP for the laptop out of the 192.168.1.X range that I needs for the wired network. Anyone have advice on an app that will not bump my IP outside that? I tried FoxFi and can't get that to even work right (heard something about a known bug).
OK, my wife and I each have Sprint Samsung Galaxy S3's. We both have Wifi Tether TrevE mod installed and working and we also have a linksys router running DD-WRT.
I have wanted for a long time to create a stable home network with the router using our phones for internet. Reason being, We both have laptops that need access to our WiFi networked printer. And I also wanted to create a networked storage.
I started out trying to use the Router as a repeater bridge. The problem here is that in that mode there is no DHCP server in the router, so when you turn off WiFi Tether in the phone, there is no IP assignment taking place since it is handled by the phone. This is ok for the printer because we can set a static IP, but not ok for the laptops because they need to have auto ip assignment for all the other networks they might encounter. Plus I'd like to be able to have a friend come over and use the printer if need be without having to change his IP address. So this setup is unstable.
Then I tried the Router in Repeater mode. In this mode IP addresses are being assigned and everyone can see everyone else on the network. The problem here though, is that the Router and all connecting devices have to be in a separate subnet than the WiFi Tethering phone, i.e, Tethered Phone on 192.168.1.x and Router on 192.168.2.x (as far as I can tell anyway, I've tried putting them on the same subnet but fail to get internet access.) It's a problem because I have Samba Filesharing installed on the phones and the tethered phone is in a different subnet and not visible on the network. I want all devices visible.
So that's kind of where I am now, Wifi Tether on both phones (each setup with same settings so either phone can be used as our internet gateway) but they are on a separate subnet from the rest of the network while tethering.
How do I get all of my devices to be visible on the network?
Do I need a different setup in DD-WRT?
Currently it is setup in Gateway mode with DHCP server and wireless is in repeater mode with a VLAN setup with a different SSID from the WiFi tethered phone.
Do I need to usb tether the phone to the router? I have a usb port on the router but I've not found good instructions for getting the phones internet through to the router that way and I'm not sure that I would want it that way since I wouldn't be able to walk around with my phone.
Is there a way to make devices in different subnets visible to each other? Some kind of bridging or static routing or something?
Is it possible to have the phone connect to the router in a normal manner and for the router to then share the phones internet connection with the rest of the network? Then at least the router could run DHCP and be stable even without the phones.
Again, just to clarify, I want a home network with devices connecting to my WiFi router running DD-WRT and internet being provided by one of our phones, but with the network remaining intact when the internet provided phone is removed. Thanks for your help.
Bonus questions:
Is it possible to harness the power of both of our phones internet connections into one network by any means possible?
Are there any other wifi/tethering apps or another version of WiFi Tether that offer more features or the functionality of DD-WRT?
did you see this?
http://forum.xda-developers.com/showthread.php?t=1548844
pbmurdoc said:
did you see this?
http://forum.xda-developers.com/showthread.php?t=1548844
Click to expand...
Click to collapse
Thanks. Not much new there other than Barnacle. Didn't know about it, tried it, doesn't work on my phone. I would like to see a version of WiFi Tether with some more options though, why couldn't we have one with the same options as DD-WRT?
I did some more reading and I think what I need to do is link the subnet created by the router to the primary router (the phone serving Wifi Tether) through static routing. Unfortunately the static route needs to be done through the primary router and WiFi Tether doesn't include features like that.
I'll do some more experimenting and see what happens.
[A] Cellular Phone/USB Modem As WAN Connection
Answer is in the DD-WRT Wiki, here (http://www.dd-wrt.com/wiki/index.php/Cellular_Phone/USB_Modem_as_WAN_connection).
Or just google "DD-WRT Cellular Phone/USB Modem As WAN Connection", it should be the #1 result.
Their WIKI is a great resource.
Good luck!
EDIT:
In retrospect, I am unsure about linking to the DD-WRT site... external and all. If this is a no-no just let me know and I will delete the link.
DD-WRT Client Bridge worked for me
I was able to do what you're trying to do by configuring my DD-WRT router as a Client Bridge.
I can't post the link, but there are directions I followed exactly on the DD-WRT wiki in the section:
DD-WRT wiki mainpage / Linking Routers / Client Bridged
I'm connecting my router to the tether via wifi, and connecting my wired devices to the router. I haven't had it working long, but so far it has been great.
Got it, sort of
Just to update this thread. The client bridge is a great way to connect a wired network to the bridge but loses out on creating a stable wi-fi network when the phone tether is turned off.
Anyway, the final setup I managed was having the DD-WRT router set as a wireless repeater with a computer connected to it running a DHCP server. The computer takes care of the IP addreses so that we have a stable wired/wi-fi intranet when the phone is not sharing it's internet connection.
Update: I founde another solution/project based on OpenWRT
http://ofmodemsandmen.com/
my exploits using a Linksys E3000 have been documented here:
http://tweakedrom.com/forum/viewtopic.php?f=6&t=7
I kind of like the USB tether thing. The E3000 Router USB power charges and maintains my SCH-i605 (Verizon Samsung GN2) running CM12.1. I use this as a backup connection or in the event of main cable modem service disruption at the house. It is also great for traveling (hotels) or camping (car 12v adapter for router, or power inverter)
I just bought a used Asus RT-N66U router. Out of the box it supports USB tethering with android phones and dual WANs for failover/load balancing. ROOter also works, tested the x86 build on an old PC. I'm looking to cut out my ISP completely and just use 4G from the phone for internet. The issue I have run into is that I can't appear to do DDNS or port forwarding. My wireless carrier (verizon) appears to be employing a double NAT. If I perform a speedtest on the ookla app, I get 2 IP addresses in the results, an "internal" and an "external". Both are in the public range but I can't DDNS in with either of the IPs, nor can I get any kind of service working.
Anyone have a solution for this? I'm not 100% sure but I wonder if using the SIM card in a dedicated USB 4G modem (not tethering via the phone) would get me a direct IP? I suppose I could also sign up for a VPN service and run OpenVPN on the router but that'd cut down on speeds I think. I've also heard about punching holes for ports but I'm not 100% sure how that works, I assume I still need some 3rd party public IP for relaying or something.
Hi all,
Wondering if anyone knows of an Android app that will allow me to share the lan connection on my tablet via wifi?
Have looked at lots of hotspot type apps but the vast majority are simple shortcuts to an exisiting wifi hotspot function that shares the mobile data connection.
Seems daft to me that I have lan and wifi on my tablet but I'm looking at an ap to connect my other devices!
Thanks
Jin
I didnt understand what u said
If u want to share ur tab net to other use wifi hotspot
If u have wifi connection u can connect via wifi
Sent by typing by my fingers
Are you trying to tether your data connection or do you mean using your tablet as a hub for an existing wifi connection?
What phone do you have?
What carrier?
Did you root your phone?
Have you flashed a new ROM?
Sorry but you were rather vague in your post.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
Ok thanks. To clarify my tablet (not phone and therefore no carrier involved) has both ethernet and wifi I would like to use the ethernet to connect to my network/internet and then broadcast that connection via wifi.
This is exactly the same thing a normal wifi hotspot does except it broadcasts the mobile data connection as opposed to a wired connection.
The tablet has been flashed with Tims 6 ROM
Don't now if it's possible. On phone it;s not possible to share be a hotspot when you're on wifi. I guess it uses the same piece of hardware. That might also be the case for you with the LAN.
BTW try talking to this guy :
http://forum.xda-developers.com/showthread.php?t=1735708
he had sort of the same question perhaps he figured it out?
edit: This is also you i now see.. never mind
jontp2 said:
Ok thanks. To clarify my tablet (not phone and therefore no carrier involved) has both ethernet and wifi I would like to use the ethernet to connect to my network/internet and then broadcast that connection via wifi.
This is exactly the same thing a normal wifi hotspot does except it broadcasts the mobile data connection as opposed to a wired connection.
The tablet has been flashed with Tims 6 ROM
Click to expand...
Click to collapse
How do you have your tablet connected to the internet, wireless or wired? If wired, how did you do that? If it's wireless, you're just using your tablet as a signal booster.
What i'm confused on is if you connected your tablet wireless and want to connect other devices to your tablet's "wifi" which in essence is wifi, why can't that device connect to the same internet as your tablet?
I think we're all a bit confused on what you're trying to accomplish.
Sorry folks struggling here with what you don't get (not being smart just confused)
I have an Android tablet that has both wifi and an ethernet connection, I connect to my network via ethernet and want to use that connection to then create a wifi hotspot for my other devices to connect to.
I already do this with my win7 laptop and am looking for an app to do the same on the tablet.
If my terminology is correct I need to bridge the lan connection to the wifi adapter?