Related
This is for the people who got a new captivate through return or purchase or how ever you obtained it. If you tried flashing a new rom and now are stuck at the att boot loop or the battery loop and your phone will not boot up here is help.
1. See if your phone will do the 3 button recovery to get into download mode.
2. If you cant get into download mode you might need a Jig or do the resistor technique to get into download mode.
3. See if this odin (I897UCJF6-final-OCD-REV0.exe) will flash your phone back to the stock 2.1.
4. If after flashing the 2.1 odin and your phone still has boot loop then try the 2.2 stock odin
5. Next do the same as previous but try with this odin (I897UCJI6-OCD-REV02-Low-designgears_1_.exe) which is the 2.2 stock odin.
Note all of these flashes require you to be in download mode and have odin fired up on your pc the plug in your phone so odin can recognize it so
a. be in download mode (not connected to PC)
b. have odin open on pc
c. Plug in phone to pc and start odin.
odin likes to stop flashing when setting pit file so if it freezes give a sec and if nothing try it again.
if odin freezes on the set pit file your phone will have the dreaded phone to pc icon during boot but dont panic set your phone into download mode and try again.
If any questions should arise PM me or leave a comment and others and i will try and help.
Took me two days to fix my phone after flashing to stock to root it but i hope this helps you turn your 400 dollar paper weight back into a phone.
umm thanks but we know how to use odin there are a million guides in every ginerflash and captivate sticky.
and the 2.2 odin is actually an internal samsung beta 2.2 not official.
returning it with the designgears 2.2 will be an obvious warranty breach if they notice.
and your Step 4 and 5 seem to say the same thing... "flash 2.2 odin" (which isnt official)
and THE REAL FIX FOR THE BOOTLOOP:
reboot into RECOVERY > (not download)
wipe cache and data! (or factory reset)...
DONE!
reboot into the rom that you were trying to use!
takes 20 seconds and no reflashing anything.
i ran into this a few days ago while trying to root a friends captivate(1008) purchased from walmart recently. after trying to flash back to stock i was stuck on att boot loop and could not get into download mode via button combo to save my life. tried everthing minus a jig....after getting fed up with it, i sat it aside. to my amazment, after about 10-15 minutes the mf booted up. i had to use adb to reboot into download mode. flashed with odin(from aio toolkit) back to 2.1. everything worked fine, no problems except for one thing...sometimes it will still loop for a few minutes before it boots...sometimes it boots right away. Im still investigating the whole ordeal but my point here is: if you think your phone is stuck on att screen, just let it sit for a while....maybe a long while. and it should boot. then use adb to get back to download mode. i read every forum post on the web about this issue...just found this thread and thought id give ppl a heads up. hope it helps
I'm stuck in a bootloop right now on the Galaxy S animation screen and this wipe cache and data method doesn't seem to work for me.
so i recently tried flashing a darky rom theme onto my captivate running mosaic 8.
it worked the first time. then i tried another theme didnt like it, so flashed the darky rom one, and now, bootloop....
i can get my cappy into download mode, but odin doesn't recognize it.
i cannot get it into recovery mode with holding down the volume up and down and power button.
i need help
--edit--
fixed!
biggest help i have EVER had in custom roms/rooting etc..
http://forum.xda-developers.com/showthread.php?t=1351224
TRusselo said:
umm thanks but we know how to use odin there are a million guides in every ginerflash and captivate sticky.
and the 2.2 odin is actually an internal samsung beta 2.2 not official.
returning it with the designgears 2.2 will be an obvious warranty breach if they notice.
and your Step 4 and 5 seem to say the same thing... "flash 2.2 odin" (which isnt official)
and THE REAL FIX FOR THE BOOTLOOP:
reboot into RECOVERY > (not download)
wipe cache and data! (or factory reset)...
DONE!
reboot into the rom that you were trying to use!
takes 20 seconds and no reflashing anything.
Click to expand...
Click to collapse
ok cmw is not mounting cache or anything else any other ideas
Hi I want to know how can I unbrick my Samsung galaxy s 4g. I believe I bricked because now when I turned on only stock in the logo. Please can you help me with this. I'm leontx's wife. Thanks
If it's just showing the logo and it's there for over 15 minutes, you'll probably need to reflash something.
I'd suggest using one of the one-clicks from http://forum.xda-developers.com/showpost.php?p=19601810&postcount=2 and I'd probably suggest the second (Basic with a Twist) choice.
First, you need to get the phone into download mode. Easiest way to do that is to unplug USB cable, pull the battery out, plug the battery back in, and plug the phone back to the computer. Hold the volume buttons on the left and turn on the phone (while holding down the buttons). It should ask you if you want to go into download mode. Press volume+ to confirm, then unplug the phone from your computer and plug it back in (to make the computer realize that there's a device there). Now run the one-click to reflash your phone. If the flash fails, restart the phone and try again. If the phone reboots to a screen showing a little phone and a yellow warning sign, perfect... just flash it again. That's the alternate download screen, and I get it everytime I use Heimdall/Odin/Kies to flash it.
couldn't get into download mode
Hello,thanks for you help,I'm trying to fix my wife's galaxy s after she wiped and factory reset the phone when tried to recovery by herself.Now the phone is stock in the galaxy s 4g logo forever,I tried to get into recovery or download mode but i couldn't.She told me that the phone was giving her a error message about the keyboard app,then she removed the batt and put it back, the battery showed her almost dead like 1% when was like 79% few seconds before,then she called t-mobile and the person told her to do the recovery mode with the bottoms, she did it and the person ask how much batt the phone had, she said 79%.then the person sugested to full charge the batt,and call them(tmobile) back.So here we go... lol:laugh:.She tried to fix it and got into recovery mode and wiped and factory reset the phone,I dont know what she was doing and removed the batt to reboot the phone.and here we are now.When try to get into download mode the pc not recognize it say USB device not reconognized and the phone just show a loading logo but nothing happen.I just want to know if is possible to fix this or toss it,the phone is rooted with a custom rom,I tried with another batt but the same results.Im realy want to recover this phone to give it to my mother in law thank you so much
Leontx said:
Hi I want to know how can I unbrick my Samsung galaxy s 4g. I believe I bricked because now when I turned on only stock in the logo. Please can you help me with this. I'm leontx's wife. Thanks
Click to expand...
Click to collapse
i soft brick may phone yesterday, i use to flash my current rom and then reflash it again [clean flash] i just reflash it to save my game replay..
if you can boot into recovery mode, reflash your current rom and then backup and wipe everything exept sdcard then flash again.
Sounds like the battery crapping out on you & crashing while it was doing something important. Usually, a factory reset and new battery can fix. But, If the reset failed, it's not a biggie. find any of the one clicks that you might like to try (lumin30 has a awesome guide/thread w/ links). Batteries are cheap. Sometimes they will swell up when they die. If it spins easy when placed on flat surface is an easy check. There are a couple threads with links to 10 buck replacements around too.
Sent from my NookTablet using xda app-developers app
eureka !!!
my phone is alive.I could put it in download mode by removing the batt,put it back then holding both volumes bottoms,then connecting the phone to my pc(USB),no power bottom.and voila after putting this in download move everything else is piece of cake thank yall.
Ok so I'm new to the thread and basically to android tablets, so please forgive my ignorance if it should become prevalent.
I bought a Galaxy Note Pro 12.2 32GB wifi and had it for about one day. I performed a factory restore on the device in which it froze for about 2 hours. (this is probably the stupid part) I turned it off since it was not progressing after a long time and it booted up as a new device. After about 5 minutes of use, it randomly restarted and went into a boot loop. About every 15 or so boot screens, it sometimes boots up, then freezes and goes back into a boot loop. The longest it stayed active without resetting was about 10 minutes. After hours of research, I have done the following
Tried to boot into recovery to no avail. It just continuously pops up the device name screen
I have tried to flash the device with a stock rom in odin 3.9.
It recognizes the device but hangs at the Initialization stage. Sometimes it will give me a fail notice saying that it couldn't open the COM port
I've tried it on another computer, changed usb ports, powered on and off multiple times and nothing changes.
please let me know if i've forgotten anything. Any help will be appreciated.
Also I live in Japan, so if I can fix it myself that would be nice since this device isn't sold here yet, I'm not able to get support from a store. I'd like to avoid waiting a month sending it back to america, replacing it, and getting it sent back. Thanks in advance ^_^
Make sure you have the correct and latest Samsung drivers for your tablet.
If you have an SD card installed, try removing it and see if you can boot up and get it stable.
roninb30 said:
Ok so I'm new to the thread and basically to android tablets, so please forgive my ignorance if it should become prevalent.
I bought a Galaxy Note Pro 12.2 32GB wifi and had it for about one day. I performed a factory restore on the device in which it froze for about 2 hours. (this is probably the stupid part) I turned it off since it was not progressing after a long time and it booted up as a new device. After about 5 minutes of use, it randomly restarted and went into a boot loop. About every 15 or so boot screens, it sometimes boots up, then freezes and goes back into a boot loop. The longest it stayed active without resetting was about 10 minutes. After hours of research, I have done the following
Tried to boot into recovery to no avail. It just continuously pops up the device name screen
I have tried to flash the device with a stock rom in odin 3.9.
It recognizes the device but hangs at the Initialization stage. Sometimes it will give me a fail notice saying that it couldn't open the COM port
I've tried it on another computer, changed usb ports, powered on and off multiple times and nothing changes.
please let me know if i've forgotten anything. Any help will be appreciated.
Also I live in Japan, so if I can fix it myself that would be nice since this device isn't sold here yet, I'm not able to get support from a store. I'd like to avoid waiting a month sending it back to america, replacing it, and getting it sent back. Thanks in advance ^_^
Click to expand...
Click to collapse
Wow, you rooted (void warranty) on a day old tablet on a platform that is new to you? I've been rooting Android devices for over 3 years now and have had mine for a week now without root. Don't get me wrong, I have a list of things I want that require root and it will be happening but I figured I should at least run it for a couple weeks to make sure no defects pop up before I void the warranty. Good luck to you!
Russbad said:
Make sure you have the correct and latest Samsung drivers for your tablet.
If you have an SD card installed, try removing it and see if you can boot up and get it stable.
Click to expand...
Click to collapse
I've installed drivers a few times. No go.
I'm on it now and the boot loop seems to have stopped, but I still get random restarts. But each time it restarts, it's from factory, so it doesn't save anything I download or any settings such as enabling debugging in the developer settings.
rkirmeier said:
Wow, you rooted (void warranty) on a day old tablet on a platform that is new to you? I've been rooting Android devices for over 3 years now and have had mine for a week now without root. Don't get me wrong, I have a list of things I want that require root and it will be happening but I figured I should at least run it for a couple weeks to make sure no defects pop up before I void the warranty. Good luck to you!
Click to expand...
Click to collapse
I didn't root, and I haven't voided my warranty. I can still get into download mode and my flash counter is still at 0. I never tried to root, I simply wanted to flash to stock, from stock.
[Edit] I'd also like to mention that Odin has not successfully done anything, Every time I tried to flash it was done with a stock ROM, and everything that has gone wrong has occurred on nothing but the stock ROM
Is it possible that I need a pit file for the device since no version of Odin will get past initialization? ....if so where can I get one for the this model?
roninb30 said:
I've installed drivers a few times. No go.
I'm on it now and the boot loop seems to have stopped, but I still get random restarts. But each time it restarts, it's from factory, so it doesn't save anything I download or any settings such as enabling debugging in the developer settings.
I didn't root, and I haven't voided my warranty. I can still get into download mode and my flash counter is still at 0. I never tried to root, I simply wanted to flash to stock, from stock.
[Edit] I'd also like to mention that Odin has not successfully done anything, Every time I tried to flash it was done with a stock ROM, and everything that has gone wrong has occurred on nothing but the stock ROM
Click to expand...
Click to collapse
If you are not rooted and you have a boot loop I'd be returning the device for a new one...
rkirmeier said:
If you are not rooted and you have a boot loop I'd be returning the device for a new one...
Click to expand...
Click to collapse
I hate to agree since you would have to wait for a while to get the replacement, however the device sounds to be defective. just my two cents as a developer, if you flash anything to the device, root, a new image, or even the factory software, Knox will be tripped and the counter will go from zero to a one. My advice would be to get a replacement for the defective one.
Developers don't need no stinkin' signature!
If I've been able to help you, please hit the "Thanks" button.
Huge 3rd.
Device should just plain WORK out of the box. There shouldn't have been a need to flash stock to begin with.
One last suggestion, factory reset from recovery. From complete power off, hold volume up+home button+power and after a few seconds let go until it boots into recovery. From there wipe cache, wipe davlik, and factory restore. Good luck!
Android.Ninja said:
I hate to agree since you would have to wait for a while to get the replacement, however the device sounds to be defective. just my two cents as a developer, if you flash anything to the device, root, a new image, or even the factory software, Knox will be tripped and the counter will go from zero to a one. My advice would be to get a replacement for the defective one.
Developers don't need no stinkin' signature!
If I've been able to help you, please hit the "Thanks" button.
Click to expand...
Click to collapse
Yeah, it's unfortunate, but I have to suck it up and just pay the shipping back to Ameica....then again for it to come back. Just wanted to do everything I could before I had to send it. Thanks for the input though. I guess I learned quite a bit researching processes and terminology which will be helpful in the future. ^-^
Russbad said:
One last suggestion, factory reset from recovery. From complete power off, hold volume up+home button+power and after a few seconds let go until it boots into recovery. From there wipe cache, wipe davlik, and factory restore. Good luck!
Click to expand...
Click to collapse
Tried many times. The device pretty much gives me the finger by going blank and repeatedly showing the boot up logo when I hold the buttons down.
rkirmeier said:
Wow, you rooted (void warranty) on a day old tablet on a platform that is new to you? I've been rooting Android devices for over 3 years now and have had mine for a week now without root.
Click to expand...
Click to collapse
I voided my warrant after having mine for about an hour (though not new to Android). I did all my random "OCD does it work as I expect/want" tests and it passed, so I rooted. Had it for one week now, and I absolutely love everything about this tablet.
roninb30 said:
Yeah, it's unfortunate, but I have to suck it up and just pay the shipping back to Ameica
Click to expand...
Click to collapse
IMO, it will be worth it. This is my fourth tablet, and is the first one I've not had buyer's remorse with. Luckily with the gift credit for Google I was able to get the non-Tegra equivalents of some of my favorite games, too.
ExtremeRyno said:
I voided my warrant after having mine for about an hour (though not new to Android). I did all my random "OCD does it work as I expect/want" tests and it passed, so I rooted. Had it for one week now, and I absolutely love everything about this tablet.
IMO, it will be worth it. This is my fourth tablet, and is the first one I've not had buyer's remorse with. Luckily with the gift credit for Google I was able to get the non-Tegra equivalents of some of my favorite games, too.
Click to expand...
Click to collapse
After doing research, I think that even if I get a new one, I want to root it. With the problems I've read about for kitkat 4.4.2 I need to know how to fix problems, and start with a fresh install of roms and know how to use custom recovery. I haven't done anything yet, but I was wondering...
Since I'm stuck in a boot loop with no stock recovery, can I flash a custom recovery to fix my issues, flash the stock rom that is on sammobile.com and then root after that? From what I understand this is a soft brick since I can still sometimes access the device. I worked out why I couldn't access the device with adb and now it shows the device as listed. It stays on long enough to where I could flash a recovery before it restarts itself. I'm not trying to do anything stupid, just getting information before I pay the shipping for it back to the states. I've checked the knox counter in download mode, and it is still set to 0, so I haven't voided the warranty yet.
Any input would be greatly appreciated.
It's odd that a new device would not have recovery. I don't want to insult you, but just making sure we covered the basics, volume up+home+power gets you to recovery. The boot logo will flash about three times, make sure you're still pressing all three buttons, then let go after the 3rd flash of the boot logo then you should be in recovery. Volume down+home+power takes you to download mode, this is where you flash roms and recovery. I read in another post about someone not being able to get in recovery after numerous times, it turned out that he was hitting the volume down button instead of volume up. Just to be clear, if you do flash recovery, you will definitely trip knox, at this time there is no way around that.
Russbad said:
It's odd that a new device would not have recovery. I don't want to insult you, but just making sure we covered the basics, volume up+home+power gets you to recovery. The boot logo will flash about three times, make sure you're still pressing all three buttons, then let go after the 3rd flash of the boot logo then you should be in recovery. Volume down+home+power takes you to download mode, this is where you flash roms and recovery. I read in another post about someone not being able to get in recovery after numerous times, it turned out that he was hitting the volume down button instead of volume up. Just to be clear, if you do flash recovery, you will definitely trip knox, at this time there is no way around that.
Click to expand...
Click to collapse
I understand the skepticism. Yeah, I tried the button combination, usb in, usb out. I can power off the device completely only when it is plugged into power. When I hold the recovery combo from power on, the screen goes black with no flashing of the boot logo, looks as if it wants to go to recovery, and then then the boot logo comes up again, but just continues to the boot animation and continues the boot loop, even if i'm still holding down volume up and home buttons. It will sometimes boot up, then freeze after a couple of seconds, and return to boot loop. On rare occasions it will boot up, but turns me to setup like it's a brand new device. I can access everything for about 10 minutes, and then it will randomly restart and continue to boot loop again after that. I tried update/initialization in kies, but it would restart before the downloading and decompressing of binary could finish. It finished one time and then switch to a downloading screen (although it didn't say odin since you have to manually go there) but the update would freeze at 0 percent no matter how long I left the device there. It's all pretty lame ><
Hi everyone,
I'm hoping that someone can help me out with my device. I have a rooted sm-p900 that was working fine until a month ago when I tried to flash [ROM][7.1.x|SM-P900| Unofficial LineageOS 14.1 (v1awifi). I was busy multi-tasking and made the stupid mistake of flashing the rom before updating the BL. Since trying to do so, I have not been able to get past the first screen that says "Samsung sm-p900" . After the logo disappears, my screen remains lit but is just black.I could not restore my backup after either.
Where I am now:
- I can still access and use T.W.R.P. (latest 3.1.1) (If TWRP is left alone for too long, the device will reset to the same black screen and hang forever. If flashing a rom is taking long, the device will restart mid-flash as well.)
- I can still access download mode and use odin as well.
- I have since flashed the appropriate BL but that has not changed anything.
-I have tried clean flashing a magnitude of different roms and still come across the same problem.
I honestly have no idea how I can fix the device and have tried everything I know how. I would love to get it back as soon as possible. Any help is greatly appreciated, so thank you in advance!
jp2572 said:
Hi everyone,
I'm hoping that someone can help me out with my device. I have a rooted sm-p900 that was working fine until a month ago when I tried to flash [ROM][7.1.x|SM-P900| Unofficial LineageOS 14.1 (v1awifi). I was busy multi-tasking and made the stupid mistake of flashing the rom before updating the BL. Since trying to do so, I have not been able to get past the first screen that says "Samsung sm-p900" . After the logo disappears, my screen remains lit but is just black.I could not restore my backup after either.
Where I am now:
- I can still access and use T.W.R.P. (latest 3.1.1) (If TWRP is left alone for too long, the device will reset to the same black screen and hang forever. If flashing a rom is taking long, the device will restart mid-flash as well.)
- I can still access download mode and use odin as well.
- I have since flashed the appropriate BL but that has not changed anything.
-I have tried clean flashing a magnitude of different roms and still come across the same problem.
I honestly have no idea how I can fix the device and have tried everything I know how. I would love to get it back as soon as possible. Any help is greatly appreciated, so thank you in advance!
Click to expand...
Click to collapse
Have you tried taking it completely back to stock via Samsung Kies on your PC?
Sorry I don't have complete details, but it goes something like this (and if you search this site or Google, you'll find a good write-up on how to do a complete recovery using Kies):
1. If you can, make a backup using TWRP - if not, you are going to lose everything because of the next steps
2. Download and install the Kies software from the Samsung site and install it on your PC (I grabbed both versions, can install both on the same PC at the same time)
Make sure that it installs the Samsung USB driver
3. Connect to the tablet using the OEM cable - if you get a reaction from Kies, great
4. Somewhere in the Kies menu, you can tell it to do a complete recovery, including bootloader- if I remember correctly, you'll need your serial number (Sorry, been 18 months since I did just about the same thing and was able to recover it from my FUBAR, and I no longer run Windows so I can't step thru it)
It will go through downloading and flashing your tablet back to the state it was when you pulled it out of the box.
If you get to that point, you will have to go the whole route (including loading TWRP) to get it back to Lineage. It took me about two weeks to get it back to the way I had it before I was flashing and reading a book and talking to my wife all at the same time and didn't pay attention to what I touched on screen.
I apologize for the rambling and not having definitive statements, but I'm drugged up and been awake for the last 36 hours, and at my age that isn't a good combination.
Thank you so much for your help! I couldn't end up using that method because kies would not recognize my device for anything. It did get me inspired to try fixing it again however and it worked!
If anyone ever encounters the same or a similar problem, I just tried re-rooting it using odin and cf's autoroot file. It allowed me to be able to install roms again.
rhricik447 said:
Have you tried taking it completely back to stock via Samsung Kies on your PC?
Sorry I don't have complete details, but it goes something like this (and if you search this site or Google, you'll find a good write-up on how to do a complete recovery using Kies):
1. If you can, make a backup using TWRP - if not, you are going to lose everything because of the next steps
2. Download and install the Kies software from the Samsung site and install it on your PC (I grabbed both versions, can install both on the same PC at the same time)
Make sure that it installs the Samsung USB driver
3. Connect to the tablet using the OEM cable - if you get a reaction from Kies, great
4. Somewhere in the Kies menu, you can tell it to do a complete recovery, including bootloader- if I remember correctly, you'll need your serial number (Sorry, been 18 months since I did just about the same thing and was able to recover it from my FUBAR, and I no longer run Windows so I can't step thru it)
It will go through downloading and flashing your tablet back to the state it was when you pulled it out of the box.
If you get to that point, you will have to go the whole route (including loading TWRP) to get it back to Lineage. It took me about two weeks to get it back to the way I had it before I was flashing and reading a book and talking to my wife all at the same time and didn't pay attention to what I touched on screen.
I apologize for the rambling and not having definitive statements, but I'm drugged up and been awake for the last 36 hours, and at my age that isn't a good combination.
Click to expand...
Click to collapse
Try updating the bootloader again using odin
When this has happend factory reset
Flash the rom, addonsu and gapps in the same TWRP session
The rom should work then, I've been happily using it for about 6months now
Hi,
Apologies if this has been asked before, but I've done a relatively thorough search and I can't find a solution to this problem.
I have an S6 (SM-G920F), It was playing up for a few weeks before this, not charging well, and what not, thought it was a cable/hardware issue. Then it stopped working entirely. Initially when it was plugged into the wall it would say it was 91% charged, but if you tried to turn it on it would turn off, and reboot into the charging screen.
I've done quite alot of reading and I've ended up flashing it with Odin (I have a single .md5 file, which i've loaded onto the phone via AP) using the most recent FIrmware UK EE for the SM-G20F. This was successful, however now it only loads the Black screen with white text Samsung S6 powered by android screen and then goes blank and back to the white text screen.
I downloaded an alternative firmware (the one previous version), but this has had the same effect. I've tried to repartition with odin, but this fails.
1.) Is there anyway I can fix this?
2.) If not Is there anyway to remove files whilst in downlod mode?
3.) If I cannot fix it or recover my data, is there anyway to wipe the data securely from my phone so I can sell it for parts?
At present, I can't access recovery mode, only download mode. But whilst Odin communicates with the phone in download mode, I can't seem to access my files from explorer?
1. I would say you'd have to clear cache, immediately after flashing the firmware with Odin, but to do that, you'd have to get to Recovery Mode first...
Why can't you get to it? Does it just start trying to boot nornally? Because if so, it's just a matter of timing it. What I do is... hold power+home+voldown to get to the screen that asks me if I want to get into Download Mode, I press cancel, and immediately start holding power+home+volup until I see the bootsplash screen, and release the power button but keep holding home+volup, and it gets me to Recovery every time, even when I have difficulties such as this.
2. Not that I'm aware of. BUT you could flash TWRP with Odin, and if you then can manage to get to Recovery, you just need to plug your phone into a computer, and your phone will show up in the computer as a device/disk and you can freely remove stuff from it.
If... IF this were to work, I would suggest downloading a stock-based ROM and flashing it. It's far more likely to work properly and bootup without issue than the firmwares you can get, and it's far less much of a headache to do.
3. Nope. There are apps that can wipe data securely (such as Shreddit which does it according to military standards), but it can't be done from Download Mode. There may be some script that could do it in Recovery Mode, but I doubt it.
I mean... technically... you could flash TWRP, go to Recovery, move to your PC all the stuff you want to keep, select the wipe option in TWRP and then transfer randomly generated data from your PC to your phone until it's full - there are many apps that can generate such data. It's not something you could pass off as very very secure, but it should suffice.
I seem to always keep going to trying TWRP - so, you know, give it a shot.
King-V said:
1. I would say you'd have to clear cache, immediately after flashing the firmware with Odin, but to do that, you'd have to get to Recovery Mode first...
Why can't you get to it? Does it just start trying to boot nornally? Because if so, it's just a matter of timing it. What I do is... hold power+home+voldown to get to the screen that asks me if I want to get into Download Mode, I press cancel, and immediately start holding power+home+volup until I see the bootsplash screen, and release the power button but keep holding home+volup, and it gets me to Recovery every time, even when I have difficulties such as this.
2. Not that I'm aware of. BUT you could flash TWRP with Odin, and if you then can manage to get to Recovery, you just need to plug your phone into a computer, and your phone will show up in the computer as a device/disk and you can freely remove stuff from it.
If... IF this were to work, I would suggest downloading a stock-based ROM and flashing it. It's far more likely to work properly and bootup without issue than the firmwares you can get, and it's far less much of a headache to do.
3. Nope. There are apps that can wipe data securely (such as Shreddit which does it according to military standards), but it can't be done from Download Mode. There may be some script that could do it in Recovery Mode, but I doubt it.
I mean... technically... you could flash TWRP, go to Recovery, move to your PC all the stuff you want to keep, select the wipe option in TWRP and then transfer randomly generated data from your PC to your phone until it's full - there are many apps that can generate such data. It's not something you could pass off as very very secure, but it should suffice.
I seem to always keep going to trying TWRP - so, you know, give it a shot.
Click to expand...
Click to collapse
Thanks for your reply! So after flashing it goes straight back into the boot loop. Weirdly if its plugged into my laptop it spend about a second or two on the "Samsung Galaxy S6: Powered by Android" screen before plunging into darkness and shortly after repeating the same message. However if I plug it into the wall it spend over twice as long on that screen before repeating the cycle. It never goes any further.
I've tried your suggestion about perhaps its timing for recovery mode, but even if I go straight from cancelling download mode to trying the power, up and home key it doesn't go to recovery. I've tried a variety of timings both plugged into my laptop and plugged into the wall to no avail. If the phone isn't plugged in, it literally won't do anything whatsoever, won't even hint at turning on.
So Next I tried flashing it with TWRP via Odin and nothings changed, exactly the same bootloop and I still can't get into recovery mode.
I'm starting to think that sadly this phone my be beyond repair! Thanks for your help though, much appreciated.
Hi! I usually run out of my bootloops like this:
try this:
1: go to download mode, and press Power + home + volume —
2: As soon as the screen turns black, continue pressing Power and home, quickly release "volume —" and press "volume +". This will get you into recovery mode.
It always worked for me, so I wish the same for you. Good luck! (And sorry for my bad english)
vinicius_guerra said:
Hi! I usually run out of my bootloops like this:
try this:
1: go to download mode, and press Power + home + volume —
2: As soon as the screen turns black, continue pressing Power and home, quickly release "volume —" and press "volume +". This will get you into recovery mode.
It always worked for me, so I wish the same for you. Good luck! (And sorry for my bad english)
Click to expand...
Click to collapse
Hi Vinicius,
Thanks for the suggestion. Unfortunately it didn't work, I even tried flashing it back to a standard ROM from TWRP, but it still didn't do anything, just back to the Samsung logo and the loop continues ever more!
Hi, I have this problem as well.
Originally I had TWRP and root flashed into my phone but for reasons I needed to remove root.
So I followed the Odin route stated here "Mobikin how to remove root from android" (I can't post links but this should be the top result when googling)
However I didn't know if the recovery/boot should have went into AP or BL on the Odin menu and googling didn't give me any answers so I may have tried both....
Right now I tried flashing TWRP and I can't seem to boot into TWRP as well.
I was able to get into recovery mode but clearing data/cache didn't fix it for me.
EDIT: I managed to flash in another stock rom and it boots into the SAMSUNG logo but gets stuck there. I already went into recovery mode to delete data and cache partition but it still doesn't boot.
Melioetta Zyguard said:
Hi, I have this problem as well.
Originally I had TWRP and root flashed into my phone but for reasons I needed to remove root.
So I followed the Odin route stated here "Mobikin how to remove root from android" (I can't post links but this should be the top result when googling)
However I didn't know if the recovery/boot should have went into AP or BL on the Odin menu and googling didn't give me any answers so I may have tried both....
Right now I tried flashing TWRP and I can't seem to boot into TWRP as well.
I was able to get into recovery mode but clearing data/cache didn't fix it for me.
EDIT: I managed to flash in another stock rom and it boots into the SAMSUNG logo but gets stuck there. I already went into recovery mode to delete data and cache partition but it still doesn't boot.
Click to expand...
Click to collapse
Same experience. For all those 6 years that I used this device, the wifi was okay until now. It (wifi) is very buggy (turning on and off, and sometimes won't turn on at all) so I restarted the device, then bootloop happens. I flashed the stock rom via odin and clear data and cache. But it is still bootlooping. I think this is the sign that I need to replace my phone IF I couldn't find a fix to this.