I was trying to get 2.2 on my captivate. It got hung and after about an hour, I powered down phone (battery out).
I'm now getting [phone... (!).. COMPUTER] picture
Trying to get back to stock ROM 2.1, but I cannot get device in download mode
I had to use adb to get in download mode originally.
Is it possible I got a phone that doesn't go into download mode based on button combinations? If so, what do I do?
Unplug your phone from USB
Pull battery
Close Odin
Open Odin
Put in battery
Hold both volume buttons (NO POWER) and plug in USB
Hopefully this gets you into download mode
Still Fail
I've been trying that, but without open/close of Odin.
Still failed when I added that step.
get to that screen again: hold volume up/down and power at the same time.
When the screen goes black, then release power button but keep holding down volume up/down
Zilch25 said:
Unplug your phone from USB
Pull battery
Close Odin
Open Odin
Put in battery
Hold both volume buttons (NO POWER) and plug in USB
Hopefully this gets you into download mode
Click to expand...
Click to collapse
Yes, and remember to keep the volume buttons pressed in while plugging in the USB... I always hold them in until the droid/caution sign comes up.
alabamaroping said:
I was trying to get 2.2 on my captivate. It got hung and after about an hour, I powered down phone (battery out).
I'm now getting [phone... (!).. COMPUTER] picture
Trying to get back to stock ROM 2.1, but I cannot get device in download mode
I had to use adb to get in download mode originally.
Is it possible I got a phone that doesn't go into download mode based on button combinations? If so, what do I do?
Click to expand...
Click to collapse
Try the methods prescribed. There are several minor variations but you may have a phone that doesn't do three button recovery. In order to tell, we need some history on your phone. What is the RF Cal date? Were you able to three button into download before? Do you know if it was one of the ones that had the three button problem?
autocorrelation,
I tried that with the usb cable plugged in and without it plugged in.
Still no good.
joeybear23,
I've been trying that all afternoon. Probably about 50 times.
ianwood,
How do I get the RF Cal date? I don't see it under the battery where the S/N is located. I tried to do 3 button recovery to put phone into download mode when trying to install 2.2, but it wouldn't work. I had to use "adb reboot download".
I've never tried it before today. The only issue I've had was that it could NEVER connect to AT&T server to check for an update.
can you get it into recovery mode?
no recovery
No. It won't go into recovery mode either.
The only thing it WILL do is respond to all 3 buttons being pressed by the black screen flash after about 8 seconds.
If you keep holding all 3 buttons will it flash again after the initial black screen? Try releasing the power button and keeping holding vol up/down after the second black screen.
If I keep holding all 3 buttons, it just keeps flashing.
Also tried to let it flash twice (and even more) and releasing power right when it goes to black 2nd (or 3rd) time. Also tried releasing power half way through black screen, and right before black screen re-appears and also just as the screen powers back up. None of them work.
I ran into this yesterday and about freaked out. Don't panic - apparently one of the guys had this happen to them a lot. Take a deep breath, have ODIN open, plug your USB cable in, hold the volume buttons down at the same time, press and hold the power button till you see the phone to computer, and let go. You should get to the download screen again. Good luck; sucks when something like that happens and you don't know what's going on.
I know this wont help much, but I have one of the no 3 button phones, and after 20 minutes of trying all these methods, it did go into d-load mode. Unfortunately, I don't know exactly which combo I used since my brain went into overload when I finally saw the triangle appear. There is hope though, and please PLEASE post which one works for you(I'm afraid to mess with mine until I find a foolproof method)
I had a phone that wouldnt respond to ANY 3 button combo I tried. I bricked it (sorta on purpose) to the phone-!-computer screen and went and replaced the phone at AT&T (under the 30 day deal).
It didnt initially work with the 3-button but after the JH7 OTA DL mode and recovery mode work perfectly now. Also, GPS has been completely spot on when testing on my motorcycle with the phone in my backpack running my tracks.
If you are under the 30-day return policy, bring it in and come up with a good reason as to why they should give you a new phone. If not, then you're sorta SOL....
Zilch25 said:
Unplug your phone from USB
Pull battery
Close Odin
Open Odin
Put in battery
Hold both volume buttons (NO POWER) and plug in USB
Hopefully this gets you into download mode
Click to expand...
Click to collapse
This method just saved my butt!!!
I have never had trouble getting into recovery or download mode until today when I did a dumb thing. The phone would lock at the ATT screen when trying to power on and if the phone was off and I plugged it in to charge it would freeze and the circle logo that comes up before the green charging battery does.
Every method of getting into download or recovery failed up till now.
Thanks Zilch!!!
Hey guys gonna move this to Q&A.
I had this problem a few days ago after updating to 2.2. I tried every single button/usb/battery combo and nothing worked. FORTUNATELY I was within 30 days of purchasing it (I guess there's a silver lining when diving right into "hacking"), and I brought it to the store with the box and receipt and just told them it gave me an error when turning it on (played dumb) and they swapped it out without even testing. If you're over the 30 days then I think you're pretty much SOL... gotta pay for a replacement.
bricked
I declared it to be bricked and took it back to the store. I have only had it 2 weeks, so I basically pulled the same move of playing dumb and they gave me another one without any problem.
I'm wanting to try to see if I can put it in recovery mode and/or download mode with the buttons without even attaching it to anything, but now I'm paranoid about bricking it.
itsjustaphone said:
I know this wont help much, but I have one of the no 3 button phones, and after 20 minutes of trying all these methods, it did go into d-load mode. Unfortunately, I don't know exactly which combo I used since my brain went into overload when I finally saw the triangle appear. There is hope though, and please PLEASE post which one works for you(I'm afraid to mess with mine until I find a foolproof method)
Click to expand...
Click to collapse
Buddy, we need you to remember I'm in the exact position, no combo works and I bricked it after trying to load 2.2
Going into recovery or download will not brick it, its only everything after that point that might get you bricked.
So I was running Cog 2.2 Beta 1 and decided to upgrade to Beta 3. I did the Odin JF6 1-click to flash and then flashed to Cog 2.2 Beta 3, no problem.
This morning I was trying to downgrade to 2.1. I tried to go directly into download mode and holding vol up/vol down after inserting the battery while plugging in the USB cable. That did not work, it went straight to the battery charging screen. Then I used 'adb reboot download' and it worked. Odin found the phone and started flashing. And then hung. For like 8 minutes. I rebooted and now I have the exclamation point between the phone and computer pretty much no matter what. I'm thinking the 3 button recover broke somehow.
I've tried this:
Method 3: (KEY COMBO)
1. Remove the battery, sim card, sdcard if you have one
2. Insert the battery
3. Hold both Volume buttons (from i9000 just down, don't touch the power button)
4. Plug in the USB cable and continue holding both Volume buttons
Several times with no success. Any other ideas or am I screwed?
(BTW, I've searched the forums and have not come across this exact issue, so please forgive me if this is answered elsewhere.)
Thanks!
Use adb command is the fast way to get you into the current state (I've done this once myself).
There used to be instructions on the OneClick Odin thread help your recovery from this state. The way you posted above is not the one. Somehow this was removed.
IIRC, you have to use 3-button method:
1. Hold both vol+ and vol- then press and hold power button.
2. Continue to hold 3 buttons and wait for your phone to boot up then black screen then boot up again.
3. Hopefully, by second or third time, your phone will be in download mode. You can release the buttons after that.
Good luck.
I've tried this method a few times, letting up off of the power button at different stages. No luck. I think it's hosed. Stupid broken 3-button combo...
Welcome to the club, buddy... I have my Captivate on its box... showing the phone-!-Computer symbol out loud like its proud of it...
Ends up mine was bricked and AT&T says they will replace it. Which is cool, but it sucks because they will have an XML of all of my text messages, all of my TiBu files, and a ton of other personal data on the internal card that I do not know how to wipe after a brick. We'll see if they try to steal my identity or something.
I decided to install VooDoo lagfix on my new captivate when it still didn't have anything on it to minimize potential loss of information. I downloaded the lagfix, got it started, then the damn battery popped out when I got off my bed a few min into the mod. Immediately I felt like an idiot. Now, when I start my phone I get this sequence: ATT world phone screen, then a GALAXY S / GT-I9000 / SAMSUNG screen which it freezes on.
I have odin3 v1.7, but I'm unable to get it to Download Mode with any of the methods I've found (I don't know what I need for adb or what it is though...).
If I attempt to go go into download mode with Vol + & Power it shows a circle of radial lines, then it goes to a battery with the circle of radial lines (and I'm still holding both Vol + & power), then a black screen, then repeats what seems an indefinite amount of times. If I release the Power or Vol buttons it stays black for a couple seconds then it goes to the charging battery screen.
If I plug it in and turn it on with odin3 running, the phone stays on the frozen GALAXY S screen, odin3 recognizes it as COM6 but wont allow Start.
Any help would be great. My intuition says it has to be fixable if it's software.
Not sure if this will help, but earlier today I installed a theme on my phone that wasn't supported by my kernel by accident. The phone went to the AT&T World Phone screen then hit the Samsung Galaxy S screen and froze. I pulled the battery out to unfreeze the phone and then I put it back in after a few seconds and turned the phone on. I immediatly did the three button method and held it down so the phone did the AT&T World Phone/Samsung Galaxy S thing. I kept my fingers on them and the phone rebooted again (which is supposed to happen) and I kept the three buttons held down so again, it rebooted. After the second reboot I immediately took my fingers off the buttons when the AT&T World Phone screen popped up and I got into recovery. Now, this is a theme so it's totally different, but it's worth a shot and hopefully it works for you.
But if that doesn't work I still wouldn't worry as you most likely didn't brick your phone. If it was bricked it wouldn't be turning on at all and Odin is reading it at least so I'm sure with the right help if my method doesn't work, you can fix it.
Hopes this helps you man!
No power, just volume up and down plus in usb
Get a Jig. I was in the same boat. Worked like a charm.. You can make one (I did)
http://forum.xda-developers.com/showthread.php?t=841512
or you can buy a jig. Will surely work. Good luck
I dont know if this is a brick but I cant get any button combos i have tried to work this is a friends phone I am trying to fix. THis post is a copy and pase of another I found on another forup but it pretty much sums up my issue. I cant do the KDZ thing because so far I havent gotten into recovery and I saw another sugestion on how to restore the default rom and settings but it requires having the phone booting properly.
For the last several hours, I've been trying to just get my phone to turn on past the white LG logo against a black screen. I don't know how to get the phone into any kind of recovery mode or emergency mode. I've looked at tutorials on similar phones, none of the suggestions worked. Among those suggestions were:
- Hold the down volume + home button while holding the power button
- Hold the up volume + return button while holding the power button
- Hold the up volume + home button while holding the power button
I've had to take the battery out of my phone and put it back in numerous times. I've tried removing the SD card and replacing the battery. I had my phone rooted and was attempting to install custom recovery via Android Terminal. The last thing I remember was typing "su" and then at the # typing "sh /sdcard/rf.sh". The phone rebooted to the LG and I've been trying to recover ever since.
The phone isn't even recognized by my computer when connected via USB, although when the phone is connected to the computer via USB it will turn on from off position -- ostensibly I think this means it is charging?
I've read at least 12 different fixes on 12 different forums, I've googled, searched, asked for help, and my head is about to explode. There is no example that tells me anything definitive such as:
a) If my phone is for sure bricked
b) How to tell if it is for sure bricked
c) What I can do short of returning the phone
Can anyone help me to figure out a way to at least get my phone to boot up?
Hi folks. I've got a problem that I don't see anything quite matching in here. I have a Straight Talk/Verizon GS7. Last night I installed an app do to USB tethering on it. It worked great for the testing. After I disconnected and it sat idle for a while, I heard a notification sound and the blue light started flashing. I push the home key and the "back" and "window" key lit up, but the screen is black.
So here's what I've tried so far.
I tried to hold the power button to turn the phone off. Nothing.
I can soft reset by holding volume down and power. I get the splash screens for GS7, Samsung and TracFone. Then BSOD.
I can't get safe mode. I can't get recovery mode.
I can get to download mode. "Volume down, home, power"
The phone has developer tools turned on and USB debugging is enabled. Is there a way to do anything helpful from download mode? I'm not too concerned about losing data, so flashing a new ROM is fine by me.
stageman said:
Hi folks. I've got a problem that I don't see anything quite matching in here. I have a Straight Talk/Verizon GS7. Last night I installed an app do to USB tethering on it. It worked great for the testing. After I disconnected and it sat idle for a while, I heard a notification sound and the blue light started flashing. I push the home key and the "back" and "window" key lit up, but the screen is black.
So here's what I've tried so far.
I tried to hold the power button to turn the phone off. Nothing.
I can soft reset by holding volume down and power. I get the splash screens for GS7, Samsung and TracFone. Then BSOD.
I can't get safe mode. I can't get recovery mode.
I can get to download mode. "Volume down, home, power"
The phone has developer tools turned on and USB debugging is enabled. Is there a way to do anything helpful from download mode? I'm not too concerned about losing data, so flashing a new ROM is fine by me.
Click to expand...
Click to collapse
hi
Seem like flashing a new firmware may be the reasonable option...
Try flashing first with home_csc if you know what your CSC is at the moment..that way you may avoid losing your data
if that option is off the table...then use CSC and flash/ format your phone...
for your reference check here
https://forum.xda-developers.com/galaxy-s7/how-to/official-stock-firmware-update-odin-t3369431
https://www.sammobile.com/forum/showthread.php?t=30800
Pay attention to step 6 if you use CSC
Thank you for the response. While I was downloading the ROM I came across "Vysor" and was able to use it to control the phone. Using it I was able to get the phone to power off and get into recovery mode. I wiped the cache partition and uninstalled the Tether app and all is good now. Now I just have to decide whether or not to cancel the RMA that Straight Talk is sending me...
stageman said:
Thank you for the response. While I was downloading the ROM I came across "Vysor" and was able to use it to control the phone. Using it I was able to get the phone to power off and get into recovery mode. I wiped the cache partition and uninstalled the Tether app and all is good now. Now I just have to decide whether or not to cancel the RMA that Straight Talk is sending me...
Click to expand...
Click to collapse
great to know you solved.
If you know what caused the problem and fix it , i would keep the phone you have , was new when you got it right?