[Q] HTC Sensation Stuck at boot screen..Bricked? - HTC Sensation

Hello all, im fairly new to 'rooting' world and wish my first post wasn't on this, however, i'm not too sure where else to look for help! I believe my phone may be lost, but thought I'd ask before giving up completely. I was running ARHD 3.6.7 rom on my HTC Sensation. rooted, everything working like a charm, til last nite... I d/l and flash the ARHD 3.6.7 Hard Version Brightness Tweak from this post... http://forum.xda-developers.com/showthread.php?t=1350580. However, instead of going into recovery, I used rom manager ( I've read at times not to use this for certain things, so guessing this is one of em..noob mistake that may cost me my phone). While in rom manager, the following 2 options were checked, which I think is where I went wrong, 1) wipe data and cache 2) wipe dalvik cache. When my phone rebooted, the old 'android' boot image was showing instead of the 'Beats Audio' from the ARHD Rom. This is where I am at. The phone seems to be stuck at reloading this image over and over. I can not boot into recovery by holding the down volume and power. Any help would be greatly appreciated. Thanks

Chase79 said:
Hello all, im fairly new to 'rooting' world and wish my first post wasn't on this, however, i'm not too sure where else to look for help! I believe my phone may be lost, but thought I'd ask before giving up completely. I was running ARHD 3.6.7 rom on my HTC Sensation. rooted, everything working like a charm, til last nite... I d/l and flash the ARHD 3.6.7 Hard Version Brightness Tweak from this post... http://forum.xda-developers.com/showthread.php?t=1350580. However, instead of going into recovery, I used rom manager ( I've read at times not to use this for certain things, so guessing this is one of em..noob mistake that may cost me my phone). While in rom manager, the following 2 options were checked, which I think is where I went wrong, 1) wipe data and cache 2) wipe dalvik cache. When my phone rebooted, the old 'android' boot image was showing instead of the 'Beats Audio' from the ARHD Rom. This is where I am at. The phone seems to be stuck at reloading this image over and over. I can not boot into recovery by holding the down volume and power. Any help would be greatly appreciated. Thanks
Click to expand...
Click to collapse
Sholdn't have wiped anything when installing a mod, you need to open your recovery and reinstall ARHD ..if you don't have the .zip on your sdcard then just take it out of the phone and put it into the computer and copy over a .zip
you need to wipe everything before installing the ROM so user the super wipe
All can be found here..
http://forum.xda-developers.com/showthread.php?t=1098849

Friend I doubt you're bricked. Id say you had a bad install. I'd reinstall and is be happy to walk you through it. So good news is you're not bricked.
Sent from my HTC Sensation 4G using XDA App

Ok, not bricked is great! However, I do have another question. I have a pretty good uderstanding of what to do once in recovery, my question is ' how do I get there?' When I hold the down volume and power buttons, I still boot to the android screen which I am currently stuck on. I have the zip files I need on my sd card, just can't get to em... Is there another way to get into recovery to wipe and reinstall? Again, thx for the help, this is most definitely a learning experience

Chase79 said:
Ok, not bricked is great! However, I do have another question. I have a pretty good uderstanding of what to do once in recovery, my question is ' how do I get there?' When I hold the down volume and power buttons, I still boot to the android screen which I am currently stuck on. I have the zip files I need on my sd card, just can't get to em... Is there another way to get into recovery to wipe and reinstall? Again, thx for the help, this is most definitely a learning experience
Click to expand...
Click to collapse
HAve you tried pulling the battery out, then turning on to recovery

I have tried pulling the battery out, pulling the sd card out, seems like no matter, still loads to android screen. While at this screen, if i hold down power, nothing, phones stays on, if i hold down vol down + power, phone reboots to same screen. Seems like getting into recovery is my real problem...

ARHD doesn't recommend the use of Rom manager if you carefuly read the flashing instructions .further than that I had a problem like that in the past with my HTC desire ,what I did was to follow the unrevoked once again and did everything from the begining eventualy I got the recovery mode and flashed my new rom.maybe be if u follow a similar procedure by reinstalling the revolutionary kit will give u the desired outcome... Maybe sounds a bit odd but it worked for me .I don't think u have anything to lose if u try .your phone isn't bricked though by any means so no worries. Good luck maye
Sent from my HTC Sensation using xda premium

Chase79 said:
While at this screen, if i hold down power, nothing, phones stays on, if i hold down vol down + power, phone reboots to same screen.
Click to expand...
Click to collapse
Do you mean you're pressing volume down and power while your phone is already on ?

K, agreed, nothing to loose, gonna give that a go.. I am having detection issues. When I connect to pc, the device 'android phone' is recognized, but I can't access any files, HTC sync, fastboot for example saying no device connected, please check connection. I assume because the phone will not go past the boot screen? Anyhow, gonna try your suggestion. Thanks!

Mercvtio said:
Do you mean you're pressing volume down and power while your phone is already on ?
Click to expand...
Click to collapse
Yes, I have done both. While the phone is off, I have pressed vol down and power with no luck. I have also tried it while the phone was on (trying anything at that point). Still only going to android boot image.
Is there another way to enter recovery if vol down + power while phone is off doesnt work?

HALLELUJA..... Reboot into recovery successful! Not sure why, but after numerous attempt, I got it. Thx for all the quick replies. Wiping and reflashing now!!

Hey chase. Good job and have a look at coredroid Rom. Beautiful and fast. 2nd charge and at 20 hours at 49% battery left with moderate use.
Sent from my HTC Sensation 4G using XDA App

I'm having this same issue, I have used super-wipe and tried reflashing no change. still sits at the 'beats audio' flash screen. When I first tried to root the phone I believe i flashed the wrong radio zip but the hboot is version 1.23.0000 radio version is 10.14.9035.01_M whenever i try to reflash hboot or radio zips i get errors usually (status 7). It still boots into hboot and recovery just fine, but I'm not sure whats wrong or how exactly to fix it, any help would be appreciated. If you need any more information just ask. Thanks

messbarger said:
I'm having this same issue, I have used super-wipe and tried reflashing no change. still sits at the 'beats audio' flash screen. When I first tried to root the phone I believe i flashed the wrong radio zip but the hboot is version 1.23.0000 radio version is 10.14.9035.01_M whenever i try to reflash hboot or radio zips i get errors usually (status 7). It still boots into hboot and recovery just fine, but I'm not sure whats wrong or how exactly to fix it, any help would be appreciated. If you need any more information just ask. Thanks
Click to expand...
Click to collapse
Did you flash an ICS rom without installing the ICS firmware first?
If this is the case, take out your sd card, copy over the ICS firmware to the root of the sd card, boot into the bootloader, and it'll walk you through updating the firmware.

it says
model id incorrect
update fail!
press <power> to reboot.
i think the radio i tried to flash was for a different phone maybe, but it was in a tutorial to root and install arhd the tutorial said you have to update the radio to use ics. any ideas?

"model id incorrect" <- you need to super CID your phone.
Do you have adb running on your computer?

my bad guys i had supercid i hadnt changed it to 11111111 did that re-wiping and flashing now thanks for the help

Problem Solution
adamgaltress said:
Sholdn't have wiped anything when installing a mod, you need to open your recovery and reinstall ARHD ..if you don't have the .zip on your sdcard then just take it out of the phone and put it into the computer and copy over a .zip
you need to wipe everything before installing the ROM so user the super wipe
All can be found here..
http://forum.xda-developers.com/showthread.php?t=1098849
Click to expand...
Click to collapse
Follow these instructions and you will get your phone back - Had the same problem and this fixed it first time

Its been a while since this last post and I have had same problem today, 2012 March,..Using Htc super tool, while phone is off, and connected to usb cable, open htc super tool, and hit 4, it will cycle and press continue until it auotmatically boots the phone into recovery screen. Hope this helps it worked for me.

HTC Sensation Stuck at boot screen..Bricked?
I had the same issue and I was able to restore and get back to my old version.
As mentioned in
HTML:
http://forum.xda-developers.com/showthread.php?t=1192300
I followed everything, but still I cant flash my device correctly.
Here are my details.
I tried to flash ARHD 6.5.3 XE
-Revolutionary-
PYRAMID PVT SHIP S-OFF RL
HBOOT-1.17.1111
RADIO-10.14.9035.01_M
eMMC-boot
Jun 2 2011, 22:31:39

Related

Evo Shift Stuck In Boot Loop Please Help!

Hello,
I have an Evo Shift stuck in the boot loop. As soon as I put the battery in all it does is reset itself to the screen with the white background and green "HTC" logo, and will keep restarting until the battery dies.
If I hold volume down and turn it on, it does go into the bootloader, but picking ANYTHING, such as recovery or factory reset, does nothing but sending it back to the HTC screen.
I have tried flashing the RUU.exe (2.27.651.2) through Fastboot USB and it completed successfully, but it just restarts right back to the HTC screen. I have also put PG06img that I found on here on the root of my card, and it will never load it up.
Are there any other solutions anyone can think of? They would be much appreciated. I see a lot of these threads for regular Evos, but not for Shifts.
The only other thing I really know about the phone is that it is:
S-On
Hboot- 0.98.0001
Radio- 1.08.00.0506
Thank you so much for all of your help!
Seems to me you aren't rooted and that's more than likely your problem, boot into fastboot and use the ruu application for gingerbread.
Sent from my PG06100 using Tapatalk
Rooster85 said:
Seems to me you aren't rooted and that's more than likely your problem, boot into fastboot and use the ruu application for gingerbread.
Sent from my PG06100 using Tapatalk
Click to expand...
Click to collapse
While I am pretty sure I am not rooted, if you are talking about the early RUU release; 1.17.651.1, the application starts and then ends up failing in the beginning of the process. Is this what you are talking about? The drivers should be all good, the application starts to flash and then dies though. Thanks!
samcrac said:
While I am pretty sure I am not rooted, if you are talking about the early RUU release; 1.17.651.1, the application starts and then ends up failing in the beginning of the process. Is this what you are talking about? The drivers should be all good, the application starts to flash and then dies though. Thanks!
Click to expand...
Click to collapse
Use the new RUU. But make sure your SD card is formatted to a FAT32 partition. (Stock 2gig sd card and some other store boughts are not)
You can format on your computer and then place the RUU on the root of sd card again
(Bootloader won't recognize the ruu zip if not partitioned)
Sent from my Supreme Shift
notsointeresting said:
Use the new RUU. But make sure your SD card is formatted to a FAT32 partition. (Stock 2gig sd card and some other store boughts are not)
You can format on your computer and then place the RUU on the root of sd card again
(Bootloader won't recognize the ruu zip if not partitioned)
Click to expand...
Click to collapse
Ok, I just did this, everything updated fine and all completeted on the bootloader. It then said "press power to reboot." I did so, and went right back into the same boot loop. Any other ideas. I figured running this, and the RUU.exe on the computer were the sure fire ways to get this thing working again???
samcrac said:
Ok, I just did this, everything updated fine and all completeted on the bootloader. It then said "press power to reboot." I did so, and went right back into the same boot loop. Any other ideas. I figured running this, and the RUU.exe on the computer were the sure fire ways to get this thing working again???
Click to expand...
Click to collapse
So just a little information.
you said your not rooted?
So that means you have no ability to flash anything because you have no custom recovery and the bootloader isnt unlocked (S-on)
So what DID you do before it bootlooped? there had to have been something you were trying to do.
Not trying to blame anything on you at all just want to make sure we are helping the most accurate way possible
notsointeresting said:
So just a little information.
you said your not rooted?
So that means you have no ability to flash anything because you have no custom recovery and the bootloader isnt unlocked (S-on)
So what DID you do before it bootlooped? there had to have been something you were trying to do.
Not trying to blame anything on you at all just want to make sure we are helping the most accurate way possible
Click to expand...
Click to collapse
No I hear ya. I was sold the phone fairly cheap and was told "all you need to do is to reinstall the RUU, that is all that is wrong." Obviously I was skeptical, but when I checked everything out, everything looked good, and again, for the price, I knew it was a gamble. That being said, I'm sure something was tried in order to modify the phone and this is how it got like this.
I have soft bricked my old Evo 4g a handful of times and an RUU or Rom flash would always solve the problem.
Anyway, there is no custom recovery, and I'm pretty sure theres no root because it is still "S-ON," I am just trying to see if anyone here has any more info before it goes in for repair.
The only last thing I would guess you MIGHT be able to do is to install a custom recovery, but is there ANY way to do this by just being in the bootloader and using FASTBOOT USB? Any more help is greatly appreciated. Thanks!
samcrac said:
No I hear ya. I was sold the phone fairly cheap and was told "all you need to do is to reinstall the RUU, that is all that is wrong." Obviously I was skeptical, but when I checked everything out, everything looked good, and again, for the price, I knew it was a gamble. That being said, I'm sure something was tried in order to modify the phone and this is how it got like this.
I have soft bricked my old Evo 4g a handful of times and an RUU or Rom flash would always solve the problem.
Anyway, there is no custom recovery, and I'm pretty sure theres no root because it is still "S-ON," I am just trying to see if anyone here has any more info before it goes in for repair.
The only last thing I would guess you MIGHT be able to do is to install a custom recovery, but is there ANY way to do this by just being in the bootloader and using FASTBOOT USB? Any more help is greatly appreciated. Thanks!
Click to expand...
Click to collapse
It shouldn't have a custom recovery if it shows s-on.
I don't see why the RUU wouldn't work.
Honestly it doesn't sound like a softbrick- sounds like its just bricked (Which ive only heard of 1 Shift getting bricked completley)
notsointeresting said:
It shouldn't have a custom recovery if it shows s-on.
I don't see why the RUU wouldn't work.
Honestly it doesn't sound like a softbrick- sounds like its just bricked (Which ive only heard of 1 Shift getting bricked completley)
Click to expand...
Click to collapse
Make it 2! Thanks for your help though!!!
Also Stuck In A Bootloop
samcrac said:
Hello,
I have an Evo Shift stuck in the boot loop. As soon as I put the battery in all it does is reset itself to the screen with the white background and green "HTC" logo, and will keep restarting until the battery dies.
If I hold volume down and turn it on, it does go into the bootloader, but picking ANYTHING, such as recovery or factory reset, does nothing but sending it back to the HTC screen.
I have tried flashing the RUU.exe (2.27.651.2) through Fastboot USB and it completed successfully, but it just restarts right back to the HTC screen. I have also put PG06IMG that I found on here on the root of my card, and it will load it up (I'll see the blue loading bar and then the brown loading bar in the top right hand corner of the screen), but it then checks it again, and then goes back to the original screen for the bootloader.
Are there any other solutions anyone can think of? They would be much appreciated. I see a lot of these threads for regular Evos, but not for Shifts.
The only other thing I really know about the phone is that it is:
S-On
Hboot- 0.98.0001
Radio- 1.08.00.0506
Thank you so much for all of your help!
Click to expand...
Click to collapse
I'm trying to resolve a very similar problem as him, but I know of the history of my phone (since I'm the only owner), so hopefully an answer for me can assist him also.
The Story: One day, I'm playing Uno HD (downloaded from Android Market). I toss out a Draw 4, and then I see: "Google Infrastructure Failure" and a Triangle with an exclamation mark. I reset the phone, and it starts up fine. Then a few hours later, my phone randomly restarts itself into the bootloader screen after trying to reload the home screen (because the memory manager is overly aggressive).
I see no HTC Screen. It goes straight to the bootloader without any input. If I plug it to the charger from an off state, the amber light comes on, and 10 seconds later, bootloader screen. With a battery, it appears automatically after 45 seconds.
Fastboot can read my memory card just fine. It's already been re-formatted as FAT32 in my pitiful attempt to try to repair it. It's checked and read a PG06IMG file I placed on the SD Card's root, went through the entire process of reading it, but it doesn't ask me if I want to upgrade. It takes me back to the original screen. (Maybe I'm loading the wrong file).
Recovery and Factory Reset immediately restarts the bootloader after showing me the skateboarding android splash screen.
I've also tried to flash the newest stock RUU for it. (2.76.651.4), but after the RUU sends the command to start up in bootloader mode, the phone shuts off. Thus giving me the connection error.
(Maybe if someone could rewrite the .exe file to not send out the command to begin loading as if it was in the bootloader screen, it could work. I'd pay for that.)
Other Stuff:
ROM: Stock Sprint Gingerbread OTA ROM. I've been living the vanilla life. No root access. No funny stuff. Just a stock phone with apps (Third Blade, Uno HD, ASTRO File Manager, ect...)
Directly from bootloader screen:
SPEEDY XA SHIP S-ON
HBOOT-0.98.0001
RADIO-1.08.00.0506
eMMC-boot
April 11 2011, 22:32:34
Is there a way we can flash a file from the SD Card which will turn off the security and/or temp/perm root it? (forgive my noobness for such a question)
EDIT: I'm referring to a way that's outside of the adb push method. My device can't be found, and the device won't get past the bootloader screen, so that method doesn't help me too much. However, I do have the ADK Installed and the ADB Command Line works fine.
Ok .. HERE'S THE SOLUTION:
First off all if your S- ON it means you are NOT rooted
If you get stuck in a bootloop .. don't worry it can be fixed.
What you need to do is download PG06IMG.ZIP and place it on your sd card, you can access your sd card by going into recovery then mount section, then usb. This will allow you to move the file from your computer to the root of your sd card.
Once you do this be sure you back up any info you don't want to lose. Once you have the file in place, go back to fastboot ( hold vol down and power) it will read file and when it asks you to update press vol up. It will take a few minutes to update this will revert your phone back to stock but if you have an old recovery it will not do a full restore, it will only update the rom.
Once you get your phone back to working, I recommend updating your recovery by downloading Rom Manager and flashing the latest clockwork recovery. This problem happens usually due to an old recovery.
One other thing you can try if you do NOT want to reset your phone, you can try flashing a new kernal.
Sent from my PG06100 using Tapatalk
RUU won't work if your stuck in bootloop ..
Sent from my PG06100 using Tapatalk
If you want to root your phone use visionary to temp root then use shift rr .. you can then flash a custom recovery which is essential to avoid this from happening again
flylike2kites said:
I'm trying to resolve a very similar problem as him, but I know of the history of my phone (since I'm the only owner), so hopefully an answer for me can assist him also.
The Story: One day, I'm playing Uno HD (downloaded from Android Market). I toss out a Draw 4, and then I see: "Google Infrastructure Failure" and a Triangle with an exclamation mark. I reset the phone, and it starts up fine. Then a few hours later, my phone randomly restarts itself into the bootloader screen after trying to reload the home screen (because the memory manager is overly aggressive).
I see no HTC Screen. It goes straight to the bootloader without any input. If I plug it to the charger from an off state, the amber light comes on, and 10 seconds later, bootloader screen. With a battery, it appears automatically after 45 seconds.
Fastboot can read my memory card just fine. It's already been re-formatted as FAT32 in my pitiful attempt to try to repair it. It's checked and read a PG06IMG file I placed on the SD Card's root, went through the entire process of reading it, but it doesn't ask me if I want to upgrade. It takes me back to the original screen. (Maybe I'm loading the wrong file).
Recovery and Factory Reset immediately restarts the bootloader after showing me the skateboarding android splash screen.
I've also tried to flash the newest stock RUU for it. (2.76.651.4), but after the RUU sends the command to start up in bootloader mode, the phone shuts off. Thus giving me the connection error.
(Maybe if someone could rewrite the .exe file to not send out the command to begin loading as if it was in the bootloader screen, it could work. I'd pay for that.)
Other Stuff:
ROM: Stock Sprint Gingerbread OTA ROM. I've been living the vanilla life. No root access. No funny stuff. Just a stock phone with apps (Third Blade, Uno HD, ASTRO File Manager, ect...)
Directly from bootloader screen:
SPEEDY XA SHIP S-ON
HBOOT-0.98.0001
RADIO-1.08.00.0506
eMMC-boot
April 11 2011, 22:32:34
Is there a way we can flash a file from the SD Card which will turn off the security and/or temp/perm root it? (forgive my noobness for such a question)
EDIT: I'm referring to a way that's outside of the adb push method. My device can't be found, and the device won't get past the bootloader screen, so that method doesn't help me too much. However, I do have the ADK Installed and the ADB Command Line works fine.
Click to expand...
Click to collapse
Sent from my PG06100 using Tapatalk
Also if your phone can't be found its b/c you need to put it into diag mode .. ##DATA .. if you need more help google
tech-9 said:
If you want to root your phone use visionary to temp root then use shift rr .. you can then flash a custom recovery which is essential to avoid this from happening again
Sent from my PG06100 using Tapatalk
Click to expand...
Click to collapse
Sent from my PG06100 using Tapatalk
For the thread starter, the person that sold you the phone probably tried writing to the system partition with s-on. Since you can get to the bootloader, see if you can get into recovery. If you can, recovery can be seen in adb, even the stock recovery. From there, gingerbread root, plenty of guides out there, make sure you flash the misc.img, download the froyo downgrade zip (that pgimg09.zip or something like that, just search for it, but not with the numbers I just gave, those are made up.)
From there either flash the gingerbread zip or ruu, and goon with a unrooted life. Or follow one of the many guides to froyo root, and live the life of the rooted. Your choice.
For the second person with a similar issue, the same method will work for you (assuming you can get to recovery), gingerroot, froyo downgrade, and since you like being unrooted, just ruu or zip back to gingerbread.
Solution found enjoy, and just think, if root hadn't been discovered for gingerbread, you would be screwed right now, make sure to thank otaking.
I have the same boot loop problem. I tried using the PG06IMG.zip file and fastboot/bootloader screen says I have the wrong image. It's most likely because it's for 2.2 and I have 2.3. I also don't have any recovery. Is there a PG06IMG.zip for 2.3 or the like?
similar problem here
i'm fairly certain i tried recovery with the wrong or corrupt or incomplete PG06IMG.zip on my first attempt. i got the right one from here http://forum.xda-developers.com/showthread.php?t=1255474
i ran it, says update installed, but when i reboot i still get the loop
from bootloader
SPEEDY XE SHIP S-ON
HBOOT-0.93.0001
RADIO-1.07.00.1129
eMMC-boot
Nov 15 2010, 13:19:54
zdavidzz said:
i'm fairly certain i tried recovery with the wrong or corrupt or incomplete PG06IMG.zip on my first attempt. i got the right one from here http://forum.xda-developers.com/showthread.php?t=1255474
i ran it, says update installed, but when i reboot i still get the loop
from bootloader
SPEEDY XE SHIP S-ON
HBOOT-0.93.0001
RADIO-1.07.00.1129
eMMC-boot
Nov 15 2010, 13:19:54
Click to expand...
Click to collapse
Try downloading the zip again and re run it. Possibly a bad download?
Sent from my PG06100 using Tapatalk
also adb is telling me device not found. i think i might have to factory reset. is that crazy?
---------- Post added at 01:31 PM ---------- Previous post was at 01:27 PM ----------
and... that didn't help
i'm downloading the zip again right now.
since i have s-on, will i be able to install it though?
i can get the file on the root of the sdcard with an adapter since i can't push from adb. and i can't temp root the phone because if i try a normal reboot i get this stupid boot loop. is there a way to get s-off through hboot on the phone?
i don't know why i didn't notice that first file was messed up, it was only 6MB.

[Q] HTC Inspire (AT&T) clear droid 1.2.3 won't go into hboot

I'm a little stuck as to what to do now. Flashed clear droid 1.2.3 (gb) over clear droid 1.1.51 (froyo) after doing a factory reset and clearing the dalvik cache from clockwork recovery and flashing the recommended radio for gb. The stock mms app was force closing, for which ClearD recommended flashing the radio again... but the phone refuses to go into HBOOT when I hold the power button + the volume down button on startup. It just buzzes a few times and the screen stays black until I release the buttons and then it just boots normally except it gets stuck in airplane mode or refuses to recognize the SIM card until it's rebooted without holding down the volume button.
I did a backup with clockwork and a nandroid I think? If those are the same thing then I did two nandroids I'm thinking I should do another factory + dalvik wipe and flash the backup, but I'd like to get this thing on gingerbread. Any advice as to what I did wrong the first time would be greatly appreciated before I start over.
stompsfrogs said:
I'm a little stuck as to what to do now. Flashed clear droid 1.2.3 (gb) over clear droid 1.1.51 (froyo) after doing a factory reset and clearing the dalvik cache from clockwork recovery and flashing the recommended radio for gb. The stock mms app was force closing, for which ClearD recommended flashing the radio again... but the phone refuses to go into HBOOT when I hold the power button + the volume down button on startup. It just buzzes a few times and the screen stays black until I release the buttons and then it just boots normally except it gets stuck in airplane mode or refuses to recognize the SIM card until it's rebooted without holding down the volume button.
I did a backup with clockwork and a nandroid I think? If those are the same thing then I did two nandroids I'm thinking I should do another factory + dalvik wipe and flash the backup, but I'd like to get this thing on gingerbread. Any advice as to what I did wrong the first time would be greatly appreciated before I start over.
Click to expand...
Click to collapse
The good thing about Android (And ClearDroid) is that there are several ways to go about doing things.
Instead of trying the volume down + power trick, try installing the modpack (can be done by installing the zip through Rom Manager like it is a ROM) and then after install, just hold the power button, press "Reboot", then "Reboot into Bootloader" I believe.
If you still wish to try the power down option, make sure that USB Debugging is turned on and that fastboot is turned off in your settings. If still no success, post here and we will keep on troubleshooting. It might be good for others to see the steps we take to get this figured out.
:O thank you for trying to help me, master ClearD! I flashed the modpack like you said, and the sms errors went away However, I still can't get into HBOOT, and there isn't an option to do so in the modded shutdown menu Also, I don't have the option to turn off quick boot?? It's supposed to be in settings>applications>developement, right? And the phone lost the new radio! It went back to 12.56... instead of 12.62... and you said to flash that in HBOOT, so I didn't try doing it from recovery (which I can get into). I tried holding the volume button while the phone rebooted (instead of shutting it down then turning it back on) but that trick didn't work either.
It's a really sweet ROM, just so nobody gets the wrong impression from all my whining thank you for it, ClearD!
To get to the bootloader from the shutdown menu, hit "Restart" then select "Bootloader" from the next menu lol.
Try the latest release, 1.3.0, which has the advanced shutdown menu cooked back in, and the radio is not included in the Rom, it must be flashed separately or else it will stay as it was. Try that and let me know what happens.
Sent from my HTC Inspire 4G using XDA-funded carrier pigeons
Lol I'm such a tard... found bootloader... can I just put in the disclaimer that this isn't my phone? I'm trying to help a friend, I swear...
I redownloaded the radio and the checksum is 9ad454c7ac2a9bd69d9f0a5200f089b6, which is the checksum for 26.10.04.03_M (froyo radio). I'm confused, I totally downloaded 12.62.60.27P... do u um... have the right file hosted on techsupporteverything.com... when I went into HBOOT it got mad and said I needed an update so I guess that's why I got the OTA radio. Which is fine, really the sms thing was what I wanted to fix and that's all good now but I think you may have the wrong file up.
stompsfrogs said:
Lol I'm such a tard... found bootloader... can I just put in the disclaimer that this isn't my phone? I'm trying to help a friend, I swear...
I redownloaded the radio and the checksum is 9ad454c7ac2a9bd69d9f0a5200f089b6, which is the checksum for 26.10.04.03_M (froyo radio). I'm confused, I totally downloaded 12.62.60.27P... do u um... have the right file hosted on techsupporteverything.com... when I went into HBOOT it got mad and said I needed an update so I guess that's why I got the OTA radio. Which is fine, really the sms thing was what I wanted to fix and that's all good now but I think you may have the wrong file up.
Click to expand...
Click to collapse
Lol flash it and see, it should be correct though, I think...
The way the radio flashes is through hboot update, it will always ask you to update if there is any file on your microsd card named PD98IMG.zip that is valid to flash lol. I will double check though.
Sent from my HTC Inspire 4G using XDA-funded carrier pigeons

[Q] Phone won't boot into recovery, please help

Hi. This is the first time I've tried to install custom rom's on my phone so bear with me. I followed a post (since I can't post links yet just google: CyanogenMod 9 (CM9) for HTC One X is Here. It's the first link) detailing how to install CM9 on the OneX. Everything worked up until step 16 where you have to boot into recovery mode. When I select recovery mode from the bootloader, the phone just tries to restart and gets stuck at the HTC loading screen with a message underneath saying that this ROM is not official etc.
Is there an easy way to try and fix this and make it work properly? I've tried erasing the fastboot cache and that didn't make a difference. At this point I don't really care if I have to erase everything and just go back to what I had before. The phone doesn't show up as a drive on the PC when I plug it in.
Any help would be great!
SOLUTION: Ok this is what I did to get it working again. My phone is on Rogers so I had to download this RUU and then follow these steps to flash the RUU onto the phone. Pretty simple actually.
Well, I can tell you that the ROM you were trying to flash was not for the S4 variant of the HTC One X, the ROM you saw was for the international Tegra 3 chip which is VERY different. I would attempt to flash an RUU from the At&T HOX thread if that is possible. Sorry if I can't be of any more help, that's all I've got.
I just had this exact same problem on mine. Well I didn't try to install a full rom, but accidently tried to apply the mod where you remove the menu bar and remap the keys that was for the HTC One X (Internation/Tegra3) to my HTC One X (AT&T) and what happened was it would freeze at the HTC One Beats Audio screen and not do anything. Tried going to Recovery as well and nothing. So I thought. What I had to do was unplug my phone from USB, hold down power for about 7 seconds until screen goes black, immediately after screen goes black, release power button and start to hold down volume down button, this should get you to the Recovery menu. From here what you will need to do is go into FlashBoot, and then from ur PC (or mac... hopefully PC though) you need to relock your BootLoader, and get stock recovery (if you changed it). After this reboot and then go back into Recovery, FastBoot, and connect to PC. Now download the AT&T RUU (i used the newest, 1.85) and run through those steps. After this is finished phone should boot fine and your expensive device is saved.
Oh by the way, I'm an evolving Noob. Just started to do anything ...interesting... with my phone today, crap went down, and using these steps I was able to fix it, so if I am off on some of my steps or unclear, just comment please and I'll try and correct myself or giver farther details on what I did.
-Good Luck
Thanks for the replies but I think my situation is further complicated by the fact that my phone is a Rogers phone. I know the RUU is 1.73.631.1 but I don't know if a stock recovery is available for Rogers yet. It sounds like all I have to do is find the correct RUU and flash it to the phone.
TrueLandon, you said after you held the power button down for 7 seconds you could put the phone into recovery mode. Would that be the same thing as the bootloader menu (where you can select fastboot, factory reset etc)?
achoj said:
Thanks for the replies but I think my situation is further complicated by the fact that my phone is a Rogers phone. I know the RUU is 1.73.631.1 but I don't know if a stock recovery is available for Rogers yet. It sounds like all I have to do is find the correct RUU and flash it to the phone.
TrueLandon, you said after you held the power button down for 7 seconds you could put the phone into recovery mode. Would that be the same thing as the bootloader menu (where you can select fastboot, factory reset etc)?
Click to expand...
Click to collapse
Yes, sorry if I were unclear, still trying to learn the lingo and technical terms , and yea, that's what you would need then is the RUU for Rogers, but I think the other steps should work for you.
I'll PM you a link to 1.73 RUU for Rogers
achoj said:
Hi. This is the first time I've tried to install custom rom's on my phone so bear with me. I followed a post (since I can't post links yet just google: CyanogenMod 9 (CM9) for HTC One X is Here. It's the first link) detailing how to install CM9 on the OneX. Everything worked up until step 16 where you have to boot into recovery mode. When I select recovery mode from the bootloader, the phone just tries to restart and gets stuck at the HTC loading screen with a message underneath saying that this ROM is not official etc.
Is there an easy way to try and fix this and make it work properly? I've tried erasing the fastboot cache and that didn't make a difference. At this point I don't really care if I have to erase everything and just go back to what I had before. The phone doesn't show up as a drive on the PC when I plug it in.
Any help would be great!
EDIT: Is it even possible to do a factory reset at this point?
Click to expand...
Click to collapse
The facepalm is significant and this makes me wish HTC forced carriers to label the S4 One X as the One XL.
If your bootloader was unlocked, lock the bootloader and run the RUU from fastboot.
Thanks for the replies guys. Truelandon sent me the RUU that I need for my phone but there's no .exe file in it. I was just wondering if I can somehow use these files and flash my phone with this RUU. Most of the files that I ended up downloading are disk image files.
Addition to the issue
I flashed a cm9 rom on my hox (international version). Its working fine but the only issue is that i want to install black and cyan theme to it and when i try to flash it and the moment i hit recovery in boot loader my phone restarts and comes back normal.so i can't enter cwm to flash the theme.
manmeets said:
I flashed a cm9 rom on my hox (international version). Its working fine but the only issue is that i want to install black and cyan theme to it and when i try to flash it and the moment i hit recovery in boot loader my phone restarts and comes back normal.so i can't enter cwm to flash the theme.
Click to expand...
Click to collapse
Wrong forum you have the international one x the is the one xl forum so we can't really help your phone has completely different partitions.
The only thing I would suggest is to reflash your cwm and see if it helps.
Sent from my HTC One XL using Forum Runner

[Q] HTC One S Terrible bootloop/soft brick on TrickDroid ,cant find solution

Ok guys, new to the forums but this problem has had me fully occupied for the last 6 hours and I feel like I have tried everything. I had cm9 alpha 12, and went to flash TrickDroid v5.0, something happened and I'm currently stuck in some wierd bootloop/soft brick. I had access to CWM but my SD card wouldn't mount and my adb push attempts didn't do anything, for reasons I don't know why. My phone would start up into the wierd trickdroid bootup and last for like 30 minutes. I tried the solution of another thread on how to fix a bootloop/ softbrick, but now I dont have any CWM access and I can only access the bootloader or the endless bootup screen. I tried using the all in one tool to flash the CWM again but it just restarts it and puts it back into the bootup, and when i restart to go to bootloader to acess the recovery, it goes back to bootup. Every solution I try makes my problem worse, and to top it off I cant turn my phone off and keep it off because it will just start back up. Thanks.
Edit: Problem fixed. Downloaded the original all in 1 tool for htc one s, plugged phone into comp went to fastboot and with the tool flashed the phones stock recovery. I reset to factory defaults and cleared storage with it from the bootloader. After that, I flashed clockwork mod recovery again and my SD card was able to be mounted and accepted files from my adb push, and I reflashed cyanogenmod. Wuzzah!
milesmarrero said:
Ok guys, new to the forums but this problem has had me fully occupied for the last 6 hours and I feel like I have tried everything. I had cm9 alpha 12, and went to flash TrickDroid v5.0, something happened and I'm currently stuck in some wierd bootloop/soft brick. I had access to CWM but my SD card wouldn't mount and my adb push attempts didn't do anything, for reasons I don't know why. My phone would start up into the wierd trickdroid bootup and last for like 30 minutes. I tried the solution of another thread on how to fix a bootloop/ softbrick, but now I dont have any CWM access and I can only access the bootloader or the endless bootup screen. I tried using the all in one tool to flash the CWM again but it just restarts it and puts it back into the bootup, and when i restart to go to bootloader to acess the recovery, it goes back to bootup. Every solution I try makes my problem worse, and to top it off I cant turn my phone off and keep it off because it will just start back up. Thanks.
Click to expand...
Click to collapse
lol, meant to "quote" not "thanks".
Can you fastboot a new recovery?
Did you do a full wipe coming from CM9 to TrickDroid
Well I can't access the phone from usb on my computer (still takes charge though), so I don't think I can flash a recovery thru fastboot (I'm not too experienced though). From cm9, I wiped all and flashed trickdroid + tweak set, then it just stat their at home screen. CMW being lost occurred later.
Im in the same situation rght now. I have trickdroid and I went into my tweaks to set them back to their original setup...so removing all of the options I chose before when I used the tweaks for the first time. When I rebooted my phone it just hangs on the HTC screen. I can get into recovery and I tried reinstalling trickdroid but its still getting stuck. Not sure what to do at this point. I don't think I can put a recovery file on this since I can't connect it to my computer.
Hopefully someone can help us.
But the thing is I can't access recovery. I try to flash it again with the all in 1 tool and it won't work. It says it went through, but accessing it doesn't work.
If its recognised by USB when plugged in computer just run an ruu that's my solution all The time lol
Sent from my HTC One S using xda premium
Ok i somehow managed to get TWR on my phone, but still unable to mount the SD. How do I run the RUU? I downloaded it, but the instructions are flawed I think
Connect with USB to.computer go into faatboot USB then run ruu on pc
Sent from my HTC One S using xda premium
Well I thought the RUU was going to work, but it just stops at the HTC and gives me an error saying I can't. What now?
Ok currently, I relocked my bootloader in an attempt to do the RUU, but I get a 155 Unknown Error up doing such, using the TMOUS 1.53 ruu... other places I have seen say something about returning to the stock img etc, but I'm quite stuck. Any advice appreciated
htc one s stuck in bootloop almost unresponsive
hey guys, got a brain teaser for you.
i have a tmobile htc one s, unlocked, rooted using all in one htc tool, been at it for two days now. im stuck on the boot screen showing its unlocked, i used to be able to get into the boot loader screen but now it seems ive dead ended. ill hold any combination of power and vol up/down, the keys flash for 10 sec and the screen flashes once, i let go and it reboots, keeps that htc screen, after 20-30 sec goes black. my pc doings like it detects a device but i cant locate it. ive used adb and the htc all in one unlock tool trying to get any kind of os to launch.
Shortly before this i was able to go into the boot loader, clear and master reset the files and cache, and search for the rom zip, thus never allowing me to flash. on a journey to place this in the phone through various combinations of the all in one, adb push, and everything else i found on youtube, countless forum posts, i seem to be in a deeper hole now.
I ultimately want to end with a cm10 nightly on my tmo htc one s. I have never done this to a phone without a sd card. i come to this community humbly seeking any and all advice. thank you.

Bricked Inspire After New Rom Install

hello all,
I am new here and I have been searching the forums for a few days as well as the internet but I could not seem to find one that had my same problem, but if there is can you please direct me to it and apologies for that.
I was installing a new rom, the Blackout ICS Incredible v3.0.0 FULLY WORKING!!! [4.0.4][Sense 3.6], onto my inspire i did a full wipe using FULL_WIPE_1.5_EXT4_.zip and I cleared the caches. the install i thought went well because it went to 100% and i even chose what kind of background i could as well as choosing to over clock my processor. The phone the restarted after all of that and it went to the htc screen then faded to black, after about ten minutes of it being black screen i pulled out the battery.
Now when i try to recover it it wont go into hboot and it just goes to the htc white screen then it quickly fades to a black screen and stays like that.
so my question to you all is a Jtag the only way i can save my phone or is there something else i can do?
http://forum.xda-developers.com/showthread.php?p=30480411
Sent from a dream.
Teichopsia said:
http://forum.xda-developers.com/showthread.php?p=30480411
Sent from a dream.
Click to expand...
Click to collapse
Im sorry but I dont understand. I cannot enter hboot no mater what i do and don't you need to enter hboot to reflash it?
True, but I'm hoping you are doing something wrong.
Pull battery, wait a few minutes, place back in. Press and hold Volume down, then power button. Does it go into hboot? If not.
Read this.
http://forum.xda-developers.com/showthread.php?p=20382502
Edit: you are the first report with that issue after trying to flash that rom. My bet (that is, if you are new), you are not doing something wrong.
2nd edit: if you are new, then read the guide in post#7
http://forum.xda-developers.com/showthread.php?p=30007255
Sent from a dream.
Teichopsia said:
True, but I'm hoping you are doing something wrong.
Pull battery, wait a few minutes, place back in. Press and hold Volume down, then power button. Does it go into hboot? If not.
Read this.
http://forum.xda-developers.com/showthread.php?p=20382502
Edit: you are the first report with that issue after trying to flash that rom. My bet (that is, if you are new), you are not doing something wrong.
.
Click to expand...
Click to collapse
I really appreciate the help Teichopsia , but I've tried the power /volume - method many times and it still wont go to hboot. if it helps this is the 5 time i have have flashed a rom on my phone (and it is rooted) and yes sadly i had to be the first person to be unlucky enough to get my phone bricked from the blackout rom :crying:
i think i could get out of this mess if i could only get into hboot.
reading the method you linked to me will it work if i cant even get to the hboot screen? my phone only stays of the white htc logo screen for about 3 seconds then it goes to a lit black screen
on a side note should i report what happened to team blackout to see if they have any soloutions?
The only thing I can think of is trying to get into hboot without the sd card and sim card.
The rest is beyond my knowledge.
You'll need to wait for someone more knowledgable than myself to help you.
Remember, first press and hold the volume down button, while holding that down press the power button. Do not release either button till it shows the hboot. If that doesn't work, pull the battery for five minutes and try again. If you did this part exactly like that, then you can skip it.
Well, you already posyed your issue here, just wait for someone to help you. Glevitan is bound to show up sooner or later.
Sent from a dream.
I would see if you can send commands to it from adb while its in the blacked out state. adb is pretty easy to use and can be found easy online. if you get it installed type "adb devices", if it recognizes your device type "adb reboot bootloader" or "adb reboot recovery".
Novius vi said:
hello all,
I am new here and I have been searching the forums for a few days as well as the internet but I could not seem to find one that had my same problem, but if there is can you please direct me to it and apologies for that.
I was installing a new rom, the Blackout ICS Incredible v3.0.0 FULLY WORKING!!! [4.0.4][Sense 3.6], onto my inspire i did a full wipe using FULL_WIPE_1.5_EXT4_.zip and I cleared the caches. the install i thought went well because it went to 100% and i even chose what kind of background i could as well as choosing to over clock my processor. The phone the restarted after all of that and it went to the htc screen then faded to black, after about ten minutes of it being black screen i pulled out the battery.
Now when i try to recover it it wont go into hboot and it just goes to the htc white screen then it quickly fades to a black screen and stays like that.
so my question to you all is a Jtag the only way i can save my phone or is there something else i can do?
Click to expand...
Click to collapse
i also have the same problem. i'm using a DHD. and to add to that, my volume rocker is broken. i wonder why the warning not to select reboot immediately after installation wasnt part of the download as a readme or something. i may have just lost a perfectly good phone as a result
I can confirm as a third user and one knowledgable in flashing roms that the ICS blackout does the same thing to my phone. I can also confirm that pulling the battery and then trying hboot just results in the white htc screen instead of just popping up hboot. I was able to boot into recovery from the white htc screen by using adb and doing the "adb reboot recovery" command. I am able to restore my backup just fine so you guys will be able to fix it. it must just have a bad boot image for the version of hboot that we have installed.
Gizmoe said:
I can confirm as a third user and one knowledgable in flashing roms that the ICS blackout does the same thing to my phone. I can also confirm that pulling the battery and then trying hboot just results in the white htc screen instead of just popping up hboot. I was able to boot into recovery from the white htc screen by using adb and doing the "adb reboot recovery" command. I am able to restore my backup just fine so you guys will be able to fix it. it must just have a bad boot image for the version of hboot that we have installed.
Click to expand...
Click to collapse
Im sorry but this is the first time i have ever done something like that can you give me a step by step instruction how to do it or a link that says how, i dont want to sound lazy but I scared to mess up my phone even more
Use this guide its very easy. if you have already used your phone on your pc and the drivers are installed all you need to do is download the easyadb and follow the instrucions to where is says to type adb.exe. once it is started just type adb devices to make sure it sees your device and then adb reboot recovery
Ignore the fact the instructions are written for a xoom as it will work for any android device with the drivers already installed, which they should be from rooting, syncing and all the other stuff you have probably already done on pc.
UPDATE: I reinstalled ICS blackout but instead of wiping myself i just let aroma installer do it and everything went fine this time. I noticed the aroma installer reformats everything to ext4. its not mentioned in the op as a requirement but seems thats the case. Hboot version has nothing to do with it like i previously commented. It really is a cool rom with both ics and sense. I have only tried the sense version so far
Hope this helps?
Novius vi said:
Im sorry but this is the first time i have ever done something like that can you give me a step by step instruction how to do it or a link that says how, i dont want to sound lazy but I scared to mess up my phone even more
Click to expand...
Click to collapse
Just in case-- to get into recovery you must press and hold the volume down for a few seconds and then hold the power button. Do not do press them both at the same time. I realize you wrote that your volume rocker seems or is broken but I wrote above just in case-- when I first tried to root my phone, I was pushing them both at first and thought my rocker was broken....
Since you rooted the phone originally-- not sure how you did it. But if you go to this link you can download recovery flash. Read the "readme" file:
http://forum.xda-developers.com/showpost.php?p=29208930&postcount=10
Assuming you can get into recovery-- then reload the blackout ROM but you MUST let the aroma installer wipe and format do not use any other wipe/format tool. Then do NOT press the "FINISH" button-- instead press the back arrow-- you want to go back to flash recovery and reboot from there. If you press finish (like I did multiple times, the phone will just lockup).
Best of luck!
Three of us confirmed that hboot was inaccessible even after battery pull. I am no stranger to this device as well. The only fix was using adb reboot. Also if you actually reformat your partitions to ext4 before install, then aroma will install correctly. It's just not mounting anything if it's still in ext3 format. Definitely better to just do the full wipe within aroma though. I do agree with not hitting restart from aroma but someone already mentioned that a few posts up.
Thank you thank you thank you
After putting it into abd it recognized it and then i was able to put it into hboot. Im not out of the woods yet, but after not being to see hboot in so long, well its just amazing to see it again
ok now its in hboot it gives me 4 choices
bootloader
Reboot
Reboot Bootloader
power down
apologies again but just for reassurance which one should i select?
THANK YOU GUYS for getting me this far!!!
special thanks to Gizmoe for suggesting the adb route
Novius vi said:
After putting it into abd it recognized it and then i was able to put it into hboot. Im not out of the woods yet, but after not being to see hboot in so long, well its just amazing to see it again
ok now its in hboot it gives me 4 choices
bootloader
Reboot
Reboot Bootloader
power down
apologies again but just for reassurance which one should i select?
THANK YOU GUYS for getting me this far!!!
special thanks to Gizmoe for suggesting the adb route
Click to expand...
Click to collapse
Select bootloader to get to recovery option.
1shukla said:
Just in case-- to get into recovery you must press and hold the volume down for a few seconds and then hold the power
Assuming you can get into recovery-- then reload the blackout ROM but you MUST let the aroma installer wipe and format do not use any other wipe/format tool. Then do NOT press the "FINISH" button-- instead press the back arrow-- you want to go back to flash recovery and reboot from there. If you press finish (like I did multiple times, the phone will just lockup).
Best of luck!
Click to expand...
Click to collapse
I did exactly as you said I pressed finished and it asked if i wanted to reboot i said no. then it sent me back to recovery mode crossing my fingers hoping to see that it works:fingers-crossed:
Now, just manually reboot.
Sent from a dream.
You saved my phone!!
Thank you guys sooo much this Rom is great once I got past that minor issue
My phones working better than ever I even oced it a little bit
Again I am eternally grateful to you guys and team black out for this great Rom!

Categories

Resources