Hello,
I think emmc chip on my phone is dead. Do you know how much cost repair of emmc chip problem because I can't find that info on search.
All the best,
maxpowermne
maxpowermne said:
Hello,
I think emmc chip on my phone is dead. Do you know how much cost repair of emmc chip problem because I can't find that info on search.
All the best,
maxpowermne
Click to expand...
Click to collapse
I think you should replace the whole motherboard.
As my father used to say : a repaired phone is not like a brand new one.
---------- Post added at 02:02 AM ---------- Previous post was at 01:59 AM ----------
Also try typing in cmd dmesg | grep mmc0 with your phone connected to the pc via cable.You will need adb shell.
Ok, i typed that and I got this in CMD:
Code:
~ # dmesg | grep mmc0
dmesg | grep mmc0
<3>[ 8.580383] mmc0: No card detect facilities available
<6>[ 8.580902] mmc0: Qualcomm MSM SDCC at 0x00000000a0500000 irq 98,0 dma 7
<6>[ 8.581146] mmc0: Platform slot type: MMC
<6>[ 8.581268] mmc0: 4 bit data mode disabled
<6>[ 8.581390] mmc0: 8 bit data mode enabled
<6>[ 8.581634] mmc0: MMC clock 144000 -> 50000000 Hz, PCLK 96000000 Hz
<6>[ 8.581756] mmc0: Slot eject status = 0
<6>[ 8.581970] mmc0: Power save feature enable = 1
<6>[ 8.582122] mmc0: DM non-cached buffer at ffa0f000, dma_addr 0x0bb02000
<6>[ 8.582336] mmc0: DM cmd busaddr 0x0bb02000, cmdptr busaddr 0x0bb02300
<6>[ 8.736114] mmc0: new high speed MMC card at address 0001
<6>[ 8.737365] mmcblk0: mmc0:0001 M4G2DE 2.10 GiB
<3>[ 12.548736] mmc0: Failed to get card ready i = 127100
<6>[ 12.548828] mmc0: reinit card
<4>[ 12.548919] mmc0: Starting deferred resume
<6>[ 14.590759] mmc0: Deferred resume failed
<3>[ 14.595336] mmc0: DMA channel flushed (0x80000004)
<6>[ 14.595703] mmc0: Controller has been reset
<6>[ 14.595886] mmc0: Worked around bug 1535304
<3>[ 14.597320] mmc0: DMA channel flushed (0x80000004)
<6>[ 14.597686] mmc0: Controller has been reset
<6>[ 14.597869] mmc0: Worked around bug 1535304
<6>[ 14.604461] mmc0: reinit card
<4>[ 14.604553] mmc0: Starting deferred resume
<6>[ 16.642761] mmc0: Deferred resume failed
<3>[ 16.695770] mmc0: DMA channel flushed (0x80000004)
<6>[ 16.696228] mmc0: Controller has been reset
<6>[ 16.696380] mmc0: Worked around bug 1535304
<3>[ 16.697753] mmc0: DMA channel flushed (0x80000004)
<6>[ 16.698120] mmc0: Controller has been reset
<6>[ 16.698364] mmc0: Worked around bug 1535304
<6>[ 16.704986] mmc0: reinit card
<4>[ 16.705078] mmc0: Starting deferred resume
<6>[ 18.744812] mmc0: Deferred resume failed
<3>[ 18.747650] mmc0: DMA channel flushed (0x80000004)
<6>[ 18.748016] mmc0: Controller has been reset
<6>[ 18.748199] mmc0: Worked around bug 1535304
<3>[ 18.749572] mmc0: DMA channel flushed (0x80000004)
<6>[ 18.750030] mmc0: Controller has been reset
<6>[ 18.750183] mmc0: Worked around bug 1535304
<6>[ 18.756805] mmc0: reinit card
<4>[ 18.756896] mmc0: Starting deferred resume
<6>[ 20.796752] mmc0: Deferred resume failed
<3>[ 20.798828] mmc0: DMA channel flushed (0x80000004)
<6>[ 20.799255] mmc0: Controller has been reset
<6>[ 20.799438] mmc0: Worked around bug 1535304
<3>[ 20.800811] mmc0: DMA channel flushed (0x80000004)
<6>[ 20.801147] mmc0: Controller has been reset
<6>[ 20.801422] mmc0: Worked around bug 1535304
<6>[ 20.807983] mmc0: reinit card
<4>[ 20.808074] mmc0: Starting deferred resume
<6>[ 22.848815] mmc0: Deferred resume failed
<3>[ 23.129882] mmc0: DMA channel flushed (0x80000004)
<6>[ 23.130249] mmc0: Controller has been reset
<6>[ 23.130432] mmc0: Worked around bug 1535304
<3>[ 23.131866] mmc0: DMA channel flushed (0x80000004)
<6>[ 23.132232] mmc0: Controller has been reset
<6>[ 23.132385] mmc0: Worked around bug 1535304
<6>[ 23.139038] mmc0: reinit card
<4>[ 23.139160] mmc0: Starting deferred resume
<6>[ 25.181091] mmc0: Deferred resume failed
<3>[ 25.183227] mmc0: DMA channel flushed (0x80000004)
<6>[ 25.183593] mmc0: Controller has been reset
<6>[ 25.183776] mmc0: Worked around bug 1535304
<3>[ 25.185241] mmc0: DMA channel flushed (0x80000004)
<6>[ 25.185577] mmc0: Controller has been reset
<6>[ 25.185760] mmc0: Worked around bug 1535304
<6>[ 25.192321] mmc0: reinit card
<4>[ 25.192504] mmc0: Starting deferred resume
<6>[ 27.233093] mmc0: Deferred resume failed
<3>[ 27.312652] mmc0: DMA channel flushed (0x80000004)
<6>[ 27.313018] mmc0: Controller has been reset
<6>[ 27.313171] mmc0: Worked around bug 1535304
<3>[ 27.314666] mmc0: DMA channel flushed (0x80000004)
<6>[ 27.315032] mmc0: Controller has been reset
<6>[ 27.315185] mmc0: Worked around bug 1535304
<6>[ 27.321746] mmc0: reinit card
<4>[ 27.321868] mmc0: Starting deferred resume
<6>[ 29.355133] mmc0: Deferred resume failed
<3>[ 29.357238] mmc0: DMA channel flushed (0x80000004)
<6>[ 29.357604] mmc0: Controller has been reset
<6>[ 29.357788] mmc0: Worked around bug 1535304
<3>[ 29.359161] mmc0: DMA channel flushed (0x80000004)
<6>[ 29.359527] mmc0: Controller has been reset
<6>[ 29.359771] mmc0: Worked around bug 1535304
<6>[ 29.366363] mmc0: reinit card
<4>[ 29.366455] mmc0: Starting deferred resume
<6>[ 31.407165] mmc0: Deferred resume failed
<3>[ 31.478424] mmc0: DMA channel flushed (0x80000004)
<6>[ 31.478759] mmc0: Controller has been reset
<6>[ 31.479034] mmc0: Worked around bug 1535304
<3>[ 31.480407] mmc0: DMA channel flushed (0x80000004)
<6>[ 31.480743] mmc0: Controller has been reset
<6>[ 31.480987] mmc0: Worked around bug 1535304
<6>[ 31.487609] mmc0: reinit card
<4>[ 31.487701] mmc0: Starting deferred resume
<6>[ 33.529174] mmc0: Deferred resume failed
<3>[ 33.531311] mmc0: DMA channel flushed (0x80000004)
<6>[ 33.531677] mmc0: Controller has been reset
<6>[ 33.531951] mmc0: Worked around bug 1535304
<3>[ 33.533325] mmc0: DMA channel flushed (0x80000004)
<6>[ 33.533691] mmc0: Controller has been reset
<6>[ 33.533874] mmc0: Worked around bug 1535304
<6>[ 33.540527] mmc0: reinit card
<4>[ 33.540618] mmc0: Starting deferred resume
Battery light is ok when i plug charger, i can go i hboot and i can go in recovery but i can't install new rom because i get message Aborted. ( Status 1 )
Your chip is fried....sorry bro.
And how much cost a repair for desire s ?
About 200$ or more.However the price is lower than 250$.I asked some people from vodafone and they tolld me that a motherboard replacement is 213$;price may vary in different countries.
They also tolld me that don't replace theel chip.They just replace the whole phone/mainboard.
Ok, thanks for the info!
maxpowermne said:
Hello,
I think emmc chip on my phone is dead. Do you know how much cost repair of emmc chip problem because I can't find that info on search.
All the best,
maxpowermne
Click to expand...
Click to collapse
AFAIK, it needs the whole motherboard replaced. And it cost about 250$ (at least what i've read in czech forum). But first, I would try to send it for warranty repair. I was in similar situation a month ago and they replaced the whole motherboard. Even that I was S-OFFed with alpharev tool, but I was probably lucky.
The manufacture is pretty upfront about some specs like what Video and CPU are in the device. But, I was curious about some other modules, like the radios. Could someone who has a Razr HD or Razr MAXX HD do..
Code:
> adb shell dmesg
and
Code:
> adb shell lsmod
after a fresh boot and post the results?
Thanks!
gmatrangola said:
The manufacture is pretty upfront about some specs like what Video and CPU are in the device. But, I was curious about some other modules, like the radios. Could someone who has a Razr HD or Razr MAXX HD do..
Code:
> adb shell dmesg
and
Code:
> adb shell lsmod
after a fresh boot and post the results?
Thanks!
Click to expand...
Click to collapse
completely stock never rooted Maxx HD here, what I got from dmesg:
2
<3>[ 2.420357,1] pm_chg_iterm_set: bad mA=249 asked to set
<3>[ 2.420418,1] pm8921_chg_hw_config: Failed to set term current to 249 rc=-
22
<4>[ 2.421974,1] Warning: unable to open an initial console.
<6>[ 2.422249,1] Freeing init memory: 292K
<4>[ 2.426491,0] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/
oom_score_adj instead.
<6>[ 2.457805,1] EMU-det(detection_work): state CONFIG, time since last run -
297550 ms
<6>[ 2.458080,1] EMU-det(alt_mode_setup): SEMU_ALT_MODE_EN is standard
<6>[ 2.467755,1] EMU-det(detection_work): state SAMPLE, time since last run 1
0 ms
<6>[ 2.468945,1] EMU-det(adc_vbus_get): vbus=22 mV
<6>[ 2.527788,1] EMU-det(get_sense): SEMU_PPD_DET: ID floating
<6>[ 2.587852,1] EMU-det(get_sense): No need to check DMB_PPD_DET_N
<6>[ 2.588036,1] EMU-det(sense_dp_dm): D+/D- mask: 0x10
<6>[ 2.588097,1] EMU-det(get_sense): irq=0, SESS_END, FLOAT, NO_DCD,
<6>[ 2.588219,1] EMU-det(detection_work): SAMPLE keep waiting ...
<6>[ 2.597802,1] EMU-det(detection_work): state SAMPLE, time since last run 1
30 ms
<6>[ 2.599053,1] EMU-det(adc_vbus_get): vbus=22 mV
<6>[ 2.657866,1] EMU-det(get_sense): SEMU_PPD_DET: ID floating
<6>[ 2.670288,0] keychord: using input dev keypad_8960 for fevent
<6>[ 2.670379,0] keychord: using input dev pmic8xxx_pwrkey for fevent
<3>[ 2.670624,0] init: cannot open '/initlogo.rle'
<6>[ 2.727880,1] EMU-det(get_sense): No need to check DMB_PPD_DET_N
<6>[ 2.728032,1] EMU-det(sense_dp_dm): D+/D- mask: 0x10
<6>[ 2.728124,1] EMU-det(get_sense): irq=0, SESS_END, FLOAT, NO_DCD,
<6>[ 2.728246,1] EMU-det(detection_work): state IDENTIFY, time since last run
130 ms
<6>[ 2.729497,1] EMU-det(adc_vbus_get): vbus=22 mV
<6>[ 2.778116,1] qcache: created ephemeral tmem pool, id=0, client=65535
<6>[ 2.778513,1] EXT4-fs (mmcblk0p36): mounted filesystem with ordered data m
ode. Opts: (null)
<6>[ 2.787944,1] EMU-det(get_sense): SEMU_PPD_DET: ID floating
<6>[ 2.847978,1] EMU-det(get_sense): No need to check DMB_PPD_DET_N
<6>[ 2.848069,1] EMU-det(sense_dp_dm): D+/D- mask: 0x10
<6>[ 2.848191,1] EMU-det(get_sense): irq=0, SESS_END, FLOAT, NO_DCD,
<6>[ 2.848283,1] EMU-det(detection_work): no accessory
<6>[ 2.848405,1] EMU-det(notify_accy): EMU detection Notify: NONE
<6>[ 2.848649,1] EMU-det(alt_mode_setup): SEMU_ALT_MODE_EN is standard
<6>[ 2.848802,1] EMU-det(emu_id_protection_setup): No neccessary action
<6>[ 2.848863,1] msm_otg msm_otg: received DISCONNECTED event
<6>[ 2.849015,1] msm_otg msm_otg: UNDEFINED --> IDLE
<6>[ 2.850053,1] pm8921_chg_accy_notify: pm8921_chg_accy_notify: accy_state:
7
<6>[ 2.851121,1] msm_otg msm_otg: USB in low power mode
<6>[ 8.402136,0] qcache: created ephemeral tmem pool, id=1, client=65535
<6>[ 8.402685,0] EXT4-fs (mmcblk0p38): mounted filesystem with ordered data m
ode. Opts: (null)
<6>[ 8.402929,0] qcache: destroyed pool id=1, cli_id=65535
<6>[ 8.446268,1] EXT4-fs (mmcblk0p38): barriers disabled
<6>[ 8.447733,1] qcache: created ephemeral tmem pool, id=1, client=65535
<6>[ 8.448161,1] EXT4-fs (mmcblk0p38): mounted filesystem with ordered data m
ode. Opts: noauto_da_alloc,nobarrier
<6>[ 8.451915,1] qcache: created ephemeral tmem pool, id=2, client=65535
<6>[ 8.452250,1] EXT4-fs (mmcblk0p22): mounted filesystem with ordered data m
ode. Opts: (null)
<6>[ 8.476270,1] qcache: created ephemeral tmem pool, id=3, client=65535
<6>[ 8.476484,1] EXT4-fs (mmcblk0p35): mounted filesystem with ordered data m
ode. Opts: barrier=1
<6>[ 8.492598,1] qcache: created ephemeral tmem pool, id=4, client=65535
<6>[ 8.492751,1] EXT4-fs (mmcblk0p34): mounted filesystem with ordered data m
ode. Opts: barrier=1
<6>[ 8.509873,1] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mo
de. Opts: (null)
<6>[ 8.801342,1] EXT3-fs: barriers not enabled
<6>[ 8.801770,1] kjournald starting. Commit interval 5 seconds
<6>[ 8.803021,1] EXT3-fs (mmcblk0p27): using internal journal
<6>[ 8.803113,1] qcache: created ephemeral tmem pool, id=5, client=65535
<6>[ 8.803235,1] EXT3-fs (mmcblk0p27): mounted filesystem with writeback data
mode
<6>[ 8.874042,1] EXT4-fs (mmcblk0p36): re-mounted. Opts: (null)
<3>[ 9.044437,1] init: cannot find '/system/bin/telnetd', disabling 'telnet'
<6>[ 9.114542,0] warning: `batt_health' uses 32-bit capabilities (legacy supp
ort in use)
<6>[ 9.196368,0] Adding 163836k swap on /dev/block/zram0. Priority:-1 extent
s:1 across:163836k SS
<6>[ 9.372470,1] msm_thermal: enabled = 0
<6>[ 9.971829,1] subsys-restart: restart_level_set(): Phase 3 behavior activa
ted.
<3>[ 9.972073,1] android_usb: already disabled
<6>[ 9.972623,1] mtp_bind_config
<6>[ 9.972806,1] adb_bind_config
<6>[ 9.988982,1] adb_open
<6>[ 10.081703,0] alarm_set_rtc: Failed to set RTC, time will be lost on reboo
t
<6>[ 10.122630,1] wcnss_wlan triggered by userspace
<6>[ 10.177933,0]
<6>[ 10.177933,0] Trip point triggered by current temperature (41 degrees) mea
sured by Temperature-Sensor 0
<6>[ 10.562093,0] pil_qdsp6v4 pil_qdsp6v4.0: brought out of reset
<6>[ 10.595818,0] apr_tal:Q6 Is Up
<6>[ 10.778971,1] pil_riva pil_riva: brought out of reset
<6>[ 10.797497,1] wcnss_8960: Subsystem restart activated for riva.
<6>[ 10.941889,0] pil_qdsp6v4 pil_qdsp6v4.1: brought out of reset
<6>[ 10.951442,1] panel_enable is called
<6>[ 11.118358,0] MIPI panel Manufacture_id = 0x5
<6>[ 11.118419,0] MIPI panel Controller_ver = 0x8b
<6>[ 11.118480,0] MIPI panel Controller_drv_ver = 0x9d
<6>[ 11.118510,0] panel_enable completed. Power_mode =0x9c
<3>[ 11.150923,1] acdb_mmap: PMEM is not allocated, yet!
<6>[ 11.188585,0] platform pil_dsps.0: brought out of reset
<6>[ 11.228658,0] wcnss_wlan_ctrl_probe: SMD ctrl channel up
<6>[ 11.413764,0] apr_tal: SMD_EVENT_OPEN
<6>[ 11.545276,0] dtv_on: tv_src_clk=148500kHz, pm_qos_rate=148500kHz, [0]
<6>[ 11.545948,0] hdmi_msm hdmi_msm.1: power: ON (1920x1080 148500000)
<6>[ 11.546558,0] hdmi_msm hdmi_msm.1: HPD: panel power without 'hpd' feature
on
<6>[ 11.546680,0] hdmi_msm hdmi_msm.1: power=ON DVI= ON
<6>[ 11.546772,0] msm_fb msm_fb.458753: mdp4_overlay_dtv: on
<6>[ 11.570181,0] hdmi_msm hdmi_msm.1: power: OFF (audio off, Reset Core)
<6>[ 11.570395,0] hdmi_msm hdmi_msm.1: HDMI Audio: Disabled
<6>[ 11.570547,0] dtv_off
<6>[ 11.570639,0] hdmi_pll_disable: Disabled
<6>[ 11.572897,0] msm_fb msm_fb.458753: mdp4_overlay_dtv: off
<6>[ 11.661315,0] dtv_on: tv_src_clk=148500kHz, pm_qos_rate=148500kHz, [0]
<6>[ 11.662108,0] hdmi_msm hdmi_msm.1: power: ON (1920x1080 148500000)
<6>[ 11.662261,0] hdmi_msm hdmi_msm.1: HPD: panel power without 'hpd' feature
on
<6>[ 11.662353,0] hdmi_msm hdmi_msm.1: power=ON DVI= ON
<6>[ 11.662475,0] msm_fb msm_fb.458753: mdp4_overlay_dtv: on
<6>[ 11.689119,0] hdmi_msm hdmi_msm.1: power: OFF (audio off, Reset Core)
<6>[ 11.689333,0] hdmi_msm hdmi_msm.1: HDMI Audio: Disabled
<6>[ 11.689424,0] dtv_off
<6>[ 11.689516,0] hdmi_pll_disable: Disabled
<6>[ 11.691835,0] msm_fb msm_fb.458753: mdp4_overlay_dtv: off
<6>[ 13.056493,0] apr_tal: SMD_EVENT_OPEN
<6>[ 14.658110,0] pil_qdsp6v4 pil_qdsp6v4.2: brought out of reset
<3>[ 15.361056,0] Notify: smsm init
<6>[ 15.361117,0] _smem_log_init: no static log or log_idx allocated
<6>[ 15.361269,0] _smem_log_init: no power log or log_idx allocated
<6>[ 16.945368,0] apr_tal:Modem Is Up
<6>[ 17.799298,0] sps:REVISION of BAM 0xe1814000 is 0x5.
<3>[ 18.397161,0] handle_bam_mux_cmd: dropping invalid LCID 10 reserved 0 cmd
4 pad 0 ch 10 len 0
<3>[ 18.399603,0] handle_bam_mux_cmd: dropping invalid LCID 11 reserved 0 cmd
4 pad 0 ch 11 len 0
<6>[ 21.249198,0] wcnss_post_bootup: Cancel APPS vote for Iris & Riva
<6>[ 27.029421,0] request_suspend_state: wakeup (3->0) at 27020233550 (2012-11
-12 20:50:42.977106674 UTC)
<6>[ 27.518968,1] acc_open
<6>[ 27.519029,1] acc_release
<3>[ 27.748512,0] hcismd_set_enable 0
<6>[ 27.748756,0] Bluetooth: opening HCI-SMD channel :APPS_RIVA_BT_ACL
<6>[ 27.748878,0] Bluetooth: opening HCI-SMD channel :APPS_RIVA_BT_CMD
<3>[ 31.718052,1] init: sys_prop: permission denied uid:10004 nameersist.sy
s.mot.encrypt.device
<6>[ 32.104227,1] pm8xxx_rgb_led_set: red, 0
<6>[ 32.104410,1] pm8xxx_rgb_led_set: green, 0
<6>[ 32.104562,1] pm8xxx_rgb_led_set: blue, 0
<6>[ 32.104776,1] pm8xxx_rgb_blink_store: on/off=0/0, rup=1, rdown=1
<6>[ 32.104867,1] pm8xxx_rgb_blink_set: turning blinking off
<3>[ 32.136242,1] init: sys_prop: permission denied uid:10052 name:sys.mot.ui
.launched
<3>[ 32.360292,1] init: sys_prop: permission denied uid:10004 nameersist.sy
s.mot.encrypt.device
<6>[ 33.438791,0] CPU1: shutdown
<3>[ 33.605371,0] init: untracked pid 1099 exited
<6>[ 33.621364,1] CPU1 is up
<3>[ 35.365695,1] init: sys_prop: permission denied uid:10077 nameersist.sy
s.mot.encrypt.device
<3>[ 35.366183,1] init: sys_prop: permission denied uid:10077 nameersist.sy
s.mot.encrypt.device
<3>[ 35.451854,0] init: sys_prop: permission denied uid:10077 nameersist.sy
s.mot.encrypt.device
<3>[ 35.452281,0] init: sys_prop: permission denied uid:10077 nameersist.sy
s.mot.encrypt.device
<3>[ 35.463207,0] init: sys_prop: permission denied uid:10077 nameersist.sy
s.mot.encrypt.device
<3>[ 35.464214,0] init: sys_prop: permission denied uid:10077 nameersist.sy
s.mot.encrypt.device
<3>[ 38.581565,0] init: sys_prop: permission denied uid:10017 nameersist.sy
s.mot.encrypt.device
<3>[ 39.576010,0] hcismd_set_enable 1
<3>[ 39.581168,0] hci_smd_notify_event: Frame for unknown HCI device (hdev=NUL
L)
<3>[ 39.581321,0] hci_smd_notify_data: Frame for unknown HCI device (hdev=NULL
)
<6>[ 39.967862,1] hdmi_msm hdmi_msm.1: hdmi_msm_hpd_feature: 1
<6>[ 40.059362,1] hdmi_msm hdmi_msm.1: HDMI HPD: event detected
<6>[ 40.059484,1] hdmi_msm hdmi_msm.1: HDMI HPD: QDSP OFF
<6>[ 40.059667,1] hdmi_msm hdmi_msm.1: Hdmi state switch to 0: hdmi_msm_hpd_st
ate_work
<6>[ 40.059789,1] hdmi_msm hdmi_msm.1: HDMI HPD: sense DISCONNECTED: send OFFL
INE
<3>[ 40.223164,1] hcismd_set_enable 0
<6>[ 40.225759,0] Bluetooth: opening HCI-SMD channel :APPS_RIVA_BT_ACL
<6>[ 40.225911,0] Bluetooth: opening HCI-SMD channel :APPS_RIVA_BT_CMD
<3>[ 41.147321,0] init: sys_prop: permission denied uid:10042 name:sys.mot.ui
.launched
<3>[ 41.489577,0] l2cap_sock_connect: failed -115
<3>[ 42.943781,0] l2cap_sock_connect: failed -115
<3>[ 48.497604,0] init: sys_prop: permission denied uid:10004 nameersist.sy
s.mot.encrypt.device
<3>[ 48.682191,0] init: sys_prop: permission denied uid:10004 nameersist.sy
s.mot.encrypt.device
<3>[ 50.079505,0] init: sys_prop: permission denied uid:10017 nameersist.sy
s.mot.encrypt.device
<6>[ 53.190080,1] alarm_set_rtc: Failed to set RTC, time will be lost on reboo
t
<3>[ 63.224111,0] pm_chg_ibatmax_set: bad mA=3040 asked to set
<3>[ 65.054143,0] NOHZ: local_softirq_pending 08
<3>[ 65.062200,0] NOHZ: local_softirq_pending 08
<3>[ 65.074408,0] NOHZ: local_softirq_pending 08
<3>[ 65.078681,0] NOHZ: local_softirq_pending 08
<6>[ 65.873004,0] CPU1: shutdown
<6>[ 66.223805,1] CPU1 is up
<3>[ 66.265618,0] NOHZ: local_softirq_pending 08
<3>[ 66.319609,0] NOHZ: local_softirq_pending 08
<3>[ 66.434426,0] NOHZ: local_softirq_pending 08
<3>[ 66.671692,0] NOHZ: local_softirq_pending 08
<3>[ 66.672455,0] NOHZ: local_softirq_pending 08
<6>[ 67.373996,0] CPU1: shutdown
<6>[ 67.671631,1] CPU1 is up
<3>[ 68.169296,0] NOHZ: local_softirq_pending 08
<6>[ 68.373691,0] CPU1: shutdown
<6>[ 68.721715,1] CPU1 is up
<3>[ 68.886708,1] init: sys_prop: permission denied uid:10070 name:sys.mot.ui
.launched
<6>[ 77.973111,0] CPU1: shutdown
<6>[ 77.999633,0] process 3003 (method.latinime) no longer affine to cpu1
<6>[ 78.421608,1] CPU1 is up
<6>[ 78.974637,0] CPU1: shutdown
<6>[ 79.271661,1] CPU1 is up
<6>[ 81.922905,0] CPU1: shutdown
<6>[ 82.371646,1] CPU1 is up
<6>[ 84.123027,0] CPU1: shutdown
<3>[ 87.095986,0] usbin_uv_irq_handler: USB UnderVoltage
<6>[ 87.096108,0] EMU-det(emu_det_vbus_state): PM8921 USBIN callback: in
<6>[ 87.139935,0] EMU-det(detection_work): state CONFIG, time since last run 8
4410 ms
<6>[ 87.140210,0] EMU-det(alt_mode_setup): SEMU_ALT_MODE_EN is standard
<6>[ 87.149946,0] EMU-det(detection_work): state SAMPLE, time since last run 1
0 ms
<6>[ 87.157179,0] EMU-det(adc_vbus_get): vbus=5086 mV
<6>[ 87.209888,0] EMU-det(get_sense): SEMU_PPD_DET: ID floating
<6>[ 87.269861,0] EMU-det(get_sense): No need to check DMB_PPD_DET_N
<6>[ 87.269952,0] EMU-det(sense_dp_dm): D+/D- mask: 0x0
<6>[ 87.270105,0] EMU-det(get_sense): irq=0, SESS_VLD, FLOAT, USB_DEV,
<6>[ 87.270166,0] EMU-det(detection_work): SAMPLE keep waiting ...
<6>[ 87.279902,0] EMU-det(detection_work): state SAMPLE, time since last run 1
30 ms
<6>[ 87.281092,0] EMU-det(adc_vbus_get): vbus=5085 mV
<6>[ 87.339935,0] EMU-det(get_sense): SEMU_PPD_DET: ID floating
<6>[ 87.399908,0] EMU-det(get_sense): No need to check DMB_PPD_DET_N
<6>[ 87.400061,0] EMU-det(sense_dp_dm): D+/D- mask: 0x0
<6>[ 87.400122,0] EMU-det(get_sense): irq=0, SESS_VLD, FLOAT, USB_DEV,
<6>[ 87.400274,0] EMU-det(detection_work): state IDENTIFY, time since last run
120 ms
<6>[ 87.401464,0] EMU-det(adc_vbus_get): vbus=5087 mV
<6>[ 87.459880,0] EMU-det(get_sense): SEMU_PPD_DET: ID floating
<6>[ 87.519884,0] EMU-det(get_sense): No need to check DMB_PPD_DET_N
<6>[ 87.520067,0] EMU-det(sense_dp_dm): D+/D- mask: 0x0
<6>[ 87.520128,0] EMU-det(get_sense): irq=0, SESS_VLD, FLOAT, USB_DEV,
<6>[ 87.520250,0] EMU-det(notify_accy): EMU detection Notify: USB
<6>[ 87.520524,0] EMU-det(alt_mode_setup): SEMU_ALT_MODE_EN is standard
<6>[ 87.520647,0] msm_otg msm_otg: received VBUS event
<6>[ 87.520708,0] msm_otg msm_otg: IDLE --> PERIPHERAL
<6>[ 87.520891,0] pm8921_chg_accy_notify: pm8921_chg_accy_notify: accy_state:
7
<6>[ 87.523790,0] pm8921_chg_accy_notify: pm8921_chg_accy_notify: accy_state:
0
<6>[ 87.529925,0] msm_otg msm_otg: USB exited from low power mode
<6>[ 87.650602,0] android_work: did not send uevent (0 0 (null))
<6>[ 87.687166,0] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 87.691774,0] android_work: sent uevent USB_STATE=DISCONNECTED
<6>[ 87.753059,0] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 87.841843,1] CPU1 is up
<6>[ 87.911612,0] android_usb gadget: high speed config #1: android
<6>[ 87.911826,0] msm_otg msm_otg: Avail curr from USB = 500
<6>[ 87.912376,0] android_work: sent uevent USB_STATE=CONFIGURED
<6>[ 88.520402,1] mtp_open
<6>[ 101.192034,0] CPU1: shutdown
<6>[ 108.611719,1] CPU1 is up
<6>[ 110.161971,0] CPU1: shutdown
<6>[ 112.631741,1] CPU1 is up
<6>[ 113.882099,0] CPU1: shutdown
<6>[ 115.671936,1] CPU1 is up
<6>[ 116.673157,0] CPU1: shutdown
<6>[ 116.972104,1] CPU1 is up
<6>[ 117.575736,0] CPU1: shutdown
<6>[ 121.072852,1] CPU1 is up
<3>[ 121.076575,0] init: sys_prop: permission denied uid:10017 nameersist.sy
s.mot.encrypt.device
<6>[ 121.923760,0] CPU1: shutdown
<6>[ 122.222005,1] CPU1 is up
<6>[ 122.827071,0] CPU1: shutdown
<3>[ 123.222554,0] pm_chg_ibatmax_set: bad mA=3040 asked to set
<6>[ 123.891683,1] CPU1 is up
<6>[ 124.142804,0] CPU1: shutdown
<6>[ 125.221822,1] CPU1 is up
<6>[ 125.573416,0] CPU1: shutdown
<6>[ 125.772226,1] CPU1 is up
<6>[ 126.723149,0] CPU1: shutdown
<6>[ 131.174668,1] CPU1 is up
<6>[ 131.525957,0] CPU1: shutdown
---------- Post added at 01:00 PM ---------- Previous post was at 12:55 PM ----------
gmatrangola said:
The manufacture is pretty upfront about some specs like what Video and CPU are in the device. But, I was curious about some other modules, like the radios. Could someone who has a Razr HD or Razr MAXX HD do..
Code:
> adb shell dmesg
and
Code:
> adb shell lsmod
after a fresh boot and post the results?
Thanks!
Click to expand...
Click to collapse
and what I got from lsmod (nothing really):
evfwd 4506 0 - Live 0xbf000000
I found the following from Anandtech regarding the MSM8960 and its Cell technology:
http://www.anandtech.com/show/4940/qualcomm-new-snapdragon-s4-msm8960-krait-architecture/4
Hopefully this helps somewhat.
I cannot get pass the CWM recovery. CWM wont flash any ROMs even the backup I made originally. I have copied the log to show you what I am seeing. tried to fastboot etc. no success. Please take a look and give me you expert advise, seems to brick my device. (Visual Land Connect 7).
<7>[ 29.060627] [FORMAT_ERR] There is not enough valid block for using!
<7>[ 29.066889] [FORMAT_ERR] There is not enough free blocks for distribute!
<7>[ 29.073619] [FORMAT_ERR] Format nand disk failed!
<7>[ 29.078320] [NAND]init_blklayer fail
<6>[ 29.082158] init: command 'insmod' r=0
<6>[ 29.085966] init: command 'mkdir' r=0
<6>[ 29.089655] init: command 'mkdir' r=0
<6>[ 29.093366] init: command 'mkdir' r=0
<6>[ 29.097042] init: command 'mkdir' r=0
<6>[ 29.100744] init: command 'mkdir' r=0
<6>[ 29.104428] init: command 'mkdir' r=0
<6>[ 29.108118] init: command 'mkdir' r=0
<6>[ 29.111818] init: command 'mkdir' r=0
<6>[ 29.115515] init: command 'mkdir' r=0
<6>[ 29.119254] init: command 'mount' r=0
<6>[ 29.122981] init: command 'chown' r=0
<6>[ 29.126662] init: command 'chmod' r=0
<6>[ 29.130463] init: command 'write' r=0
<6>[ 29.134199] init: command 'write' r=0
<6>[ 29.137903] init: command 'write' r=-2
<6>[ 29.141711] init: processing action 0x290f0 (property_service_init)
<3>[ 29.148092] init: Unable to open persistent property directory /data/property errno: 2
<6>[ 29.156137] init: Created socket '/dev/socket/property_service' with mode '666', user '0', group '0'
<6>[ 29.165309] init: command 'property_service_init' r=0
<6>[ 29.170457] init: processing action 0x29138 (signal_init)
<6>[ 29.175926] init: command 'signal_init' r=0
<6>[ 29.180170] init: processing action 0x29180 (check_startup)
<6>[ 29.185780] init: command 'check_startup' r=0
<6>[ 29.190208] init: processing action 0x28b20 (boot)
<6>[ 29.195513] init: command 'ifup' r=0
<6>[ 29.199209] init: command 'hostname' r=0
<6>[ 29.203287] init: command 'domainname' r=0
<3>[ 29.207511] android_usb: already disabled
<6>[ 29.211589] init: command 'write' r=0
<6>[ 29.215331] init: command 'write' r=0
<6>[ 29.219058] init: command 'write' r=0
<6>[ 29.222848] init: command 'write' r=0
<6>[ 29.226562] init: command 'setprop' r=0
<7>[ 29.230507] ep_matches, wrn: endpoint already claimed, ep(0xc08ec540, 0xd91d7400, ep1-bulk)
<6>[ 29.238865] adb_bind_config
<7>[ 29.241715] ep_matches, wrn: endpoint already claimed, ep(0xc08ec540, 0xd91d7400, ep1-bulk)
<7>[ 29.250083] ep_matches, wrn: endpoint already claimed, ep(0xc08ec580, 0xd91d7400, ep2-bulk)
<7>[ 29.258433] ep_matches, wrn: endpoint already claimed, ep(0xc08ec540, 0xd91d7400, ep1-bulk)
<7>[ 29.266798] ep_matches, wrn: endpoint already claimed, ep(0xc08ec580, 0xd91d7400, ep2-bulk)
<7>[ 29.275165] ep_matches, wrn: endpoint already claimed, ep(0xc08ec5c0, 0xd91ceb80, ep3-bulk)
<7>[ 29.283527] [sw_udc]: alloc request: ep(0xc08ec600, ep4-bulk, 512), req(0xd932d540)
<7>[ 29.291219] [sw_udc]: alloc request: ep(0xc08ec5c0, ep3-bulk, 512), req(0xd932d580)
<7>[ 29.298883] [sw_udc]: alloc request: ep(0xc08ec5c0, ep3-bulk, 512), req(0xd932d5c0)
<7>[ 29.306573] [sw_udc]: alloc request: ep(0xc08ec5c0, ep3-bulk, 512), req(0xd932d600)
<7>[ 29.314255] [sw_udc]: alloc request: ep(0xc08ec5c0, ep3-bulk, 512), req(0xd932d640)
<7>[ 29.321945] [sw_udc]: sw_udc_pullup, is_on = 1
<7>[ 29.326407] [sw_udc]: CONFIG_USB_GADGET_DUALSPEED
<7>[ 29.331141] [sw_udc]: usbd_start_work
<6>[ 29.334828] init: command 'write' r=0
<5>[ 29.338521] init: starting 'adbd'
<6>[ 29.342141] init: command 'start' r=0
<6>[ 29.345831] init: command 'setprop' r=0
<6>[ 29.351528] adb_open
<6>[ 29.356019] ===========================ft5x_ts_init=====================
<6>[ 29.362840] ft5x_ts VERSION [email protected]
<7>[ 29.367715] m_inet_ctpState return false,continue deteck
<6>[ 29.373151] ctp_fetch_sysconfig_para.
<6>[ 29.376927] ctp_fetch_sysconfig_para: after: ctp_twi_addr is 0x38, dirty_addr_buf: 0x38. dirty_addr_buf[1]: 0xfffe
<6>[ 29.387378] ctp_fetch_sysconfig_para: ctp_twi_id is 2.
<7>[ 29.392621] [sw_udc]: IRQ: suspend
<7>[ 29.396032] [sw_udc]: ERR: usb speed is unkown
<6>[ 29.400539] ctp_fetch_sysconfig_para: screen_max_x = 800.
<6>[ 29.406031] ctp_fetch_sysconfig_para: screen_max_y = 480.
<6>[ 29.411558] ctp_fetch_sysconfig_para: revert_x_flag = 0.
<6>[ 29.416956] ctp_fetch_sysconfig_para: revert_y_flag = 0.
<6>[ 29.422412] ctp_fetch_sysconfig_para: exchange_x_y_flag = 0.
<6>[ 29.428162] ctp_fetch_sysconfig_para: screen_rotate_flag = 0.
<3>[ 29.434032] ft5x_ts: script_parser_fetch err.
<6>[ 29.438474] ctp_fetch_sysconfig_para: minetPowerEnreserver = 0.
<7>[ 29.444517] script parser fetch err.
<4>[ 29.448177] touch panel tp_en request gpio fail!
<6>[ 29.452813] ft5x_ts_init: after fetch_sysconfig_para: normal_i2c: 0x38. normal_i2c[1]: 0xfffe
<7>[ 29.461558] script parser fetch err.
<4>[ 29.465217] ctp_init_platform_resource: tp_reset request gpio fail!
<6>[ 29.471501] ctp_wakeup.
<6>[ 29.514158] ctp_detect: Detected chip ft5x_ts at adapter 2, address 0x38
<7>[ 29.520888] [sw_udc]: IRQ: reset
<7>[ 29.524127] [sw_udc]: irq: reset happen, throw away all urb
<6>[ 29.529874] ====ft5x_ts_probe begin=====.
<7>[ 29.534087] I2C communication client->addr=56
<7>[ 29.627407] [sw_udc]:
<7>[ 29.629592] +++++++++++++++++++++++++++++++++++++
<7>[ 29.634474] [sw_udc]: usb enter high speed.
<7>[ 29.637396] [sw_udc]:
<7>[ 29.637396] +++++++++++++++++++++++++++++++++++++
<6>[ 29.645944] android_work: sent uevent USB_STATE=CONNECTED
<7>[ 29.651365] [sw_udc]: IRQ: reset
<7>[ 29.654604] [sw_udc]: irq: reset happen, throw away all urb
<7>[ 29.755413] [sw_udc]: Set address 5
<6>[ 29.776733] android_usb gadget: high speed config #1: android
<7>[ 29.782492] [sw_udc]: ep enable: ep3(0xc08ec5c0, ep3-bulk, 128, 512)
<7>[ 29.786716] [sw_udc]: ep enable: ep4(0xc08ec600, ep4-bulk, 0, 512)
<7>[ 29.786716] [sw_udc]: ep enable: ep1(0xc08ec540, ep1-bulk, 128, 512)
<6>[ 29.801574] android_work: sent uevent USB_STATE=CONFIGURED
<7>[ 29.807067] [sw_udc]: ep enable: ep2(0xc08ec580, ep2-bulk, 0, 512)
<7>[ 29.813301] [sw_udc]: alloc request: ep(0xc08ec540, ep1-bulk, 512), req(0xd91b3b40)
<7>[ 29.820987] [sw_udc]: alloc request: ep(0xc08ec580, ep2-bulk, 512), req(0xd91b3b80)
<7>[ 29.828656] [sw_udc]: alloc request: ep(0xc08ec540, ep1-bulk, 512), req(0xd91b3bc0)
<7>[ 29.836339] [sw_udc]: alloc request: ep(0xc08ec580, ep2-bulk, 512), req(0xd91b3c00)
<7>[ 30.040472] ft5x06 Chip ID=0x79
<7>[ 30.043611] I2C communication ok
<6>[ 30.047457] input: ft5x_ts as /devices/virtual/input/input2
<6>[ 30.053653] ==register_early_suspend =
<6>[ 30.057409] CONFIG_FT5X0X_MULTITOUCH is defined.
<6>[ 30.062193] ctp_set_irq_mode: config gpio to int mode.
<6>[ 30.067432] INTERRUPT CONFIG
<6>[ 30.070739] ==ft5x_ts_probe over =
<6>[ 30.074201] init: command 'insmod' r=0
<5>[ 30.078022] init: starting 'erase_misc'
<5>[ 30.082260] init: starting 'recovery'
<6>[ 30.086140] init: command 'class_start' r=0
<6>[ 30.095510] init: waitpid returned pid 63, status = 00000000
<5>[ 30.102973] init: process 'erase_misc', pid 63 exited
<6>[ 30.103044] init: processing action 0x291c8 (queue_property_triggers)
<6>[ 30.103062] init: command 'queue_property_triggers' r=0
<7>[ 34.791539] WRN:L1351(drivers/usb/sun4i_usb/udc/sw_udc.c):handle_ep0: ep0 setup end
<7>[ 34.799223] nuke: ep num is 0
<7>[ 72.208068] battery vol change: 13->14
<4>[ 200.118128] adbd (72): /proc/72/oom_adj is deprecated, please use /proc/72/oom_score_adj instead.
<7>[ 332.747982] battery vol change: 14->15
<7>[ 603.287563] battery vol change: 15->16
~ #
【issue】install CM-11 Android 4.4.4 [Stable v2.0][21 June] stuck in CyanogenMod screen
I install CM-11 Android 4.4.4 [Stable v2.0][21 June] use 4ext Recovery 1.0.0.6 RC3, full wipe except sdcard. In 4ext,it show install cm11 success,but when I reboot,it stuck in cyanogenmod screen. my hboot is HBOOT-1.27.1100....anybody know what is the problem????
:crying::crying::crying::crying:
You are s-off or s-on?
Sent from my HTC Sensation 4G using XDA Free mobile app
Mile_zdr said:
You are s-off or s-on?
Sent from my HTC Sensation 4G using XDA Free mobile app
Click to expand...
Click to collapse
yes,s-off,unlock,hboot 1.29.0000 fireware:3.33
it stay at the CyanogenMod arrows around screen for 30 minutes...
[email protected] said:
yes,s-off,unlock,hboot 1.29.0000 fireware:3.33
it stay at the CyanogenMod arrows around screen for 30 minutes...
Click to expand...
Click to collapse
flash the boot.img of the rom via fastboot command
fastboot flash boot boot.img
rzr86 said:
flash the boot.img of the rom via fastboot command
fastboot flash boot boot.img
Click to expand...
Click to collapse
thank u. I have done this,but it does't work....
[email protected] said:
thank u. I have done this,but it does't work....
Click to expand...
Click to collapse
try to redownload the rom maybe you have corupted rom file
[email protected] said:
thank u. I have done this,but it does't work....
Click to expand...
Click to collapse
then redownload the rom
check md5 sums
full wipe and flash
rzr86 said:
then redownload the rom
check md5 sums
full wipe and flash
Click to expand...
Click to collapse
ok,,,I reboot into recovery,use "adb shell","dmesg" show kernel log,,,I maybe know what's the problem.
~ # dmesg
dmesg
...
...
...
<3>[ 5.267850] msm_soc: create pcms
<6>[ 5.272153] asoc: CODEC_DAI <-> CPU_DAI mapping ok
<6>[ 5.284574] ALSA device list:
<6>[ 5.286222] #0: msm-audio (MSM-CARD)
<6>[ 5.288450] GACT probability NOT on
<6>[ 5.290098] Mirror/redirect action on
<6>[ 5.293668] u32 classifier
<6>[ 5.295255] Actions configured
<6>[ 5.296842] Netfilter messages via NETLINK v0.30.
<6>[ 5.300443] nf_conntrack version 0.5.0 (9010 buckets, 36040 max)
<4>[ 5.304593] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
<4>[ 5.307523] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
<4>[ 5.310392] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
<6>[ 5.313840] ctnetlink v0.93: registering with nfnetlink.
<6>[ 5.318174] xt_time: kernel timezone is -0000
<6>[ 5.323087] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 5.326291] arp_tables: (C) 2002 David S. Miller
<6>[ 5.330167] TCP cubic registered
<6>[ 5.333280] NET: Registered protocol family 10
<6>[ 5.344175] lo: Disabled Privacy Extensions
<6>[ 5.367307] Mobile IPv6
<6>[ 5.368955] IPv6 over IPv4 tunneling driver
<6>[ 5.377958] sit0: Disabled Privacy Extensions
<6>[ 5.388517] ip6tnl0: Disabled Privacy Extensions
<6>[ 5.392240] NET: Registered protocol family 17
<6>[ 5.395536] NET: Registered protocol family 15
<4>[ 5.398038] check_partition: Allocate memory for SD/eMMC card partition description (Once)
<6>[ 5.400998] mmcblk0:
<6>[ 5.408262] Bluetooth: L2CAP ver 2.14
<6>[ 5.411252] Bluetooth: L2CAP socket layer initialized
<6>[ 5.414487] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[ 5.417051] ######## bthid_init: ########
<6>[ 5.421628] ######## bthid_init: done ########
<6>[ 5.423276] ThumbEE CPU extension supported.
<4>[ 5.473356] local_clk_disable_reg: clock 33 status stuck at 'on' (bit 4 of 0xfe012fd4).
<4>[ 5.507047] local_clk_disable_reg: clock 72 status stuck at 'on' (bit 9 of 0xfe012fc8).
<6>[ 5.597623] clock_late_init() disabled 138 unused clocks
<4>[ 5.599943] p1 p2 p3 p4 <
<6>[ 5.608610] init_watchdog: dogbark processed by apps side
<6>[ 5.611814] MSM Watchdog Initialized
<4>[ 5.614377] p5 p6 p7 p8 p9 p10
<6>[ 5.641965] [Port list] init()
<6>[ 5.645688] [Port list] Virtual Address for port_list: [(null)]
<6>[ 5.647306] [Port list] Physical Address for port_list: [41E00000]
<6>[ 5.653959] [Port list] port_list is NULL.
<6>[ 5.655607] [Port list] packet filter is disabled.
<6>[ 5.666135] Acquire 'boot-time' no_halt_lock 60s
<6>[ 5.672910] cpufreq: cpu0 init at 310500 switching to 192000
<4>[ 5.674650] p11
<3>[ 5.676145] saw_set_voltage: msm_spm_set_vdd failed -5
<3>[ 5.676328] decrease_vdd: vdd_sc (cpu1) decrease failed (-5)
<6>[ 5.676511] cpufreq: cpu1 init at 310500 switching to 192000
<4>[ 5.676694] p12
<6>[ 5.677335] msm_sleep_stats: Initializing sleep stats for CPU[0]
<6>[ 5.677579] msm_sleep_stats: Initializing sleep stats for CPU[1]
<6>[ 5.677762] VFP support v0.3: implementor 51 architecture 64 part 2d variant 0 rev 0
<4>[ 5.683347] p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 >
<6>[ 5.700254] msm_sdcc_setup_vreg: Enabling SD slot power
<4>[ 5.705838] local_clk_disable_reg: clock 72 status stuck at 'on' (bit 9 of 0xfe012fc8).
<6>[ 5.754636] input: htc_headset as /devices/platform/pm8058-core.0/pm8058-othc.2/input/input9
<6>[ 5.757291] pm8058-rtc pm8058-rtc: setting system clock to 1970-01-01 00:02:22 UTC (86400)
<4>[ 5.757505] Warning: unable to open an initial console.
<6>[ 5.805539] [BATT] ID=1, level=10, vol=3300, temp=300, curr=0, dis_curr=0, chg_src=1, chg_en=0, over_vchg=0 at 5734570576 (1970-01-02 00:00:00.550413885 UTC)
<4>[ 5.819547] mmc1: high speed mode max_dtr = 50000000
<3>[ 5.819974] msm_sdc3_get_wpswitch:Failed to request GPIO 251
<4>[ 5.820066] mmc1: host does not support reading read-only switch. assuming write-enable.
<6>[ 5.820218] mmc1: new high speed SDHC card at address b368
<6>[ 5.820554] mmcblk1: mmc1:b368 00000 15.0 GiB
<6>[ 5.820981] mmcblk1: p1
<3>[ 5.891172] init: There is no cw property file /data/cw.prop.
<3>[ 5.892545] init: There is no cw property file /data/cw.prop.
<3>[ 5.892697] init: Unable to open persistent property directory /data/property errno: 2
<6>[ 5.893033] [Port list] Virtual Address of port_list: [(null)]
<6>[ 5.893125] [Port list] Physical Address of port_list: [41E00000]
<6>[ 5.893277] [Port list] port_list is NULL.
<3>[ 5.895413] init: no such service 'load-modem'
<6>[ 5.896207] [BATT] htc_batt_open: open misc device driver. at 5825115697 (1970-01-02 00:00:00.641020054 UTC)
<6>[ 5.896482] enabling adb
<7>[ 5.896726] [USB] android_enable_function: vendor_id=BB4,product_id=C86
<6>[ 5.896878] func_enable: set usb_configuration = 0
<6>[ 5.897092] [USB] msm72k_udc: ONLINE -> RESET
<6>[ 5.897184] [USB] reset controller
<6>[ 5.897245] [USBH] otg_reset
<6>[ 5.897336] [BATT] do charger control = 1 at 5826152700 (1970-01-02 00:00:00.642148557 UTC)
<6>[ 5.897580] [Port list] Virtual Address of port_list: [(null)]
<6>[ 5.897794] [Port list] Physical Address of port_list: [41E00000]
<6>[ 5.897946] [Port list] port_list is NULL.
<6>[ 5.898130] [BATT][tps65200] regh 0x00=2a, regh 0x01=29, regh 0x02=23, regh 0x03=8b
<6>[ 5.898313] adb_open
<6>[ 5.899076] [BATT][tps65200] regh 0x06=26, 0x08=0, regh 0x09=0, regh 0x0A=0
<6>[ 5.899869] [BATT][tps65200] Switch charger ON (SLOW): regh 0x03=83, regh 0x02=63
<6>[ 5.900083] [BATT] ioctl: battery level update: 38 at 5828989208 (1970-01-02 00:00:00.644863064 UTC)
<6>[ 5.900388] [BATT] Set lower threshold: 2800, upper threshold: 4400, Enabled:0. at 5829294209 (1970-01-02 00:00:00.645168065 UTC)
<3>[ 5.914426] pm_runtime: fail to wake up
<4>[ 6.074002] local_clk_disable_reg: clock 72 status stuck at 'on' (bit 9 of 0xfe012fc8).
<6>[ 6.083859] [USBH] otg_reset: mode:0x00000012
<6>[ 6.184079] [USB] ulpi: write 0x06 to 0x36
<6>[ 6.184171] [USB] ulpi: write 0x0c to 0x31
<6>[ 6.184262] [USB] ulpi: write 0x31 to 0x32
<6>[ 6.184354] [USB] ulpi: write 0x01 to 0x0e
<6>[ 6.184506] [USB] ulpi: write 0x01 to 0x11
<6>[ 6.184567] [USB] usb: notify offline
<6>[ 6.184751] [USBDIAG] diag_function_disable: dev=diag
<6>[ 6.184873] adb_release
<6>[ 6.185056] [USB] msm72k_pullup_internal: pullup
<6>[ 6.185117] adb_open
<6>[ 6.185300] [USB] msm72k_udc: RESET -> ONLINE
<6>[ 6.188291] [USB] suspend
<6>[ 6.188413] [USB] usb_get_max_power: type = 0, maxpow = 0
<6>[ 6.297238] [USB] reset
<7>[ 6.299497] [USBH] IRQ state: b_peripheral, otgsc = 0x01202e00
<7>[ 6.299588] [USBH] msm_otg_irq: portsc = 88000a05, sts = 20000084
<6>[ 6.299741] [USB] portchange USB_SPEED_HIGH
<6>[ 6.337613] [USB] reset
<7>[ 6.339871] [USBH] IRQ state: b_peripheral, otgsc = 0x01200e00
<7>[ 6.340024] [USBH] msm_otg_irq: portsc = 88000a05, sts = 20000084
<6>[ 6.340115] [USB] portchange USB_SPEED_HIGH
<6>[ 6.567105] mdp4_overlay_pipe_alloc: pipe=c06a8f74 ndx=1 num=0 share=0 cnt=0
<6>[ 6.567136] mdp4_overlay_update_dsi_cmd: blt_base=45c00000
<6>[ 6.580899] SHP: brightness orig=83, transformed=37
<6>[ 6.613675] pm8058_pwm_led_brightness_set: bank 1 brightness 1 +
<6>[ 6.613889] pm8058_pwm_led_brightness_set: bank 1 brightness 1 -
<4>[ 7.851952] local_clk_disable_reg: clock 72 status stuck at 'on' (bit 9 of 0xfe012fc8).
<3>[ 7.909050] init: untracked pid 168 exited
<6>[ 7.952446] EXT4-fs (mmcblk0p24): recovery complete
<6>[ 7.953850] EXT4-fs (mmcblk0p24): mounted filesystem with ordered data mode. Opts:
<3>[ 8.058006] EXT3-fs (mmcblk0p22): error: couldn't mount because of unsupported optional features (40)
<3>[ 8.059654] EXT2-fs (mmcblk0p22): error: couldn't mount because of unsupported optional features (44)
<6>[ 8.095177] EXT4-fs (mmcblk0p22): recovery complete
<6>[ 8.100181] EXT4-fs (mmcblk0p22): mounted filesystem with ordered data mode. Opts: (null)
<3>[ 8.101066] init: untracked pid 190 exited
<6>[ 8.382621] pm8058_led_currents_store: bank 6 currents 1 +
<6>[ 8.382744] pm8058_drvx_led_brightness_set: bank 6 brightness 0 +
<6>[ 8.383018] pm8058_drvx_led_brightness_set: bank 6 fade out brightness 0 -
<6>[ 8.383110] pm8058_drvx_led_brightness_set: bank 6 brightness 255 +
<6>[ 8.383415] pm8058_drvx_led_brightness_set: bank 6 brightness 255 -
<6>[ 8.383568] pm8058_led_currents_store: bank 6 currents 1 -
<6>[ 8.383812] pm8058_led_currents_store: bank 6 currents 6 +
<6>[ 8.383995] pm8058_drvx_led_brightness_set: bank 6 brightness 0 +
<6>[ 8.384178] pm8058_drvx_led_brightness_set: bank 6 fade out brightness 0 -
<6>[ 8.384453] pm8058_drvx_led_brightness_set: bank 6 brightness 255 +
<6>[ 8.384666] pm8058_drvx_led_brightness_set: bank 6 brightness 255 -
<6>[ 8.384819] pm8058_led_currents_store: bank 6 currents 6 -
<6>[ 8.385856] pm8058_drvx_led_brightness_set: bank 6 brightness 6 +
<6>[ 8.386161] pm8058_drvx_led_brightness_set: bank 6 brightness 6 -
<6>[ 8.386406] pm8058_drvx_led_brightness_set: bank 6 brightness 60 +
<6>[ 8.386680] pm8058_drvx_led_brightness_set: bank 6 brightness 60 -
<6>[ 8.386924] pm8058_drvx_led_brightness_set: bank 6 brightness 6 +
<6>[ 8.387230] pm8058_drvx_led_brightness_set: bank 6 brightness 6 -
<6>[ 8.387474] pm8058_drvx_led_brightness_set: bank 6 brightness 60 +
<6>[ 8.387687] pm8058_drvx_led_brightness_set: bank 6 brightness 60 -
<3>[ 8.558647] init: untracked pid 221 exited
<4>[ 8.584465] local_clk_disable_reg: clock 72 status stuck at 'on' (bit 9 of 0xfe012fc8).
<3>[ 8.827781] init: untracked pid 229 exited
<3>[ 9.110465] init: untracked pid 237 exited
<3>[ 9.397758] init: untracked pid 245 exited
<3>[ 9.680503] init: untracked pid 253 exited
<3>[ 9.967826] init: untracked pid 261 exited
<3>[ 10.254721] init: untracked pid 269 exited
<3>[ 10.541159] init: untracked pid 277 exited
<3>[ 10.828665] init: untracked pid 287 exited
<3>[ 11.115347] init: untracked pid 295 exited
<3>[ 11.402518] init: untracked pid 303 exited
<3>[ 11.689749] init: untracked pid 311 exited
<3>[ 11.972891] init: untracked pid 319 exited
<6>[ 12.001761] [DISP]init_complete_handler()
<3>[ 12.260397] init: untracked pid 327 exited
<3>[ 12.547842] init: untracked pid 335 exited
<3>[ 12.833700] init: untracked pid 343 exited
<3>[ 13.121358] init: untracked pid 351 exited
<3>[ 13.413320] init: untracked pid 359 exited
<3>[ 13.700795] init: untracked pid 367 exited
<3>[ 13.988301] init: untracked pid 375 exited
<3>[ 14.275838] init: untracked pid 383 exited
<3>[ 14.562764] init: untracked pid 391 exited
<3>[ 14.850453] init: untracked pid 399 exited
<3>[ 15.137562] init: untracked pid 407 exited
<3>[ 15.425404] init: untracked pid 415 exited
<3>[ 15.712330] init: untracked pid 423 exited
<3>[ 15.999745] init: untracked pid 431 exited
<3>[ 16.282948] init: untracked pid 439 exited
<3>[ 16.570667] init: untracked pid 447 exited
<3>[ 16.857716] init: untracked pid 455 exited
<3>[ 17.145038] init: untracked pid 463 exited
<6>[ 17.162830] android_usb gadget: high speed config #1: android
<6>[ 17.162922] adb_function_set_alt: maxsize = 512
<6>[ 17.163257] set usb_configuration = 1
<3>[ 17.635608] init: untracked pid 466 exited
<7>[ 18.035175] mmc_blk_issue_rqsd-qd)finish cmd(25) time=375976
<7>[ 18.035388] mmc_blk_issue_rq: ---(sd-qd) start sector=23732, size 9, total time=376190 microseconds
<4>[ 18.382006] local_clk_disable_reg: clock 72 status stuck at 'on' (bit 9 of 0xfe012fc8).
<4>[ 19.791978] local_clk_disable_reg: clock 72 status stuck at 'on' (bit 9 of 0xfe012fc8).
<6>[ 20.373581] [BATT] ID=2, level=38, vol=3756, temp=394, curr=0, dis_curr=98, chg_src=1, chg_en=1, over_vchg=0 at 20302010771 (1970-01-02 00:00:15.117823522 UTC)
<6>[ 38.080825] [BATT] ID=2, level=38, vol=3756, temp=394, curr=0, dis_curr=98, chg_src=1, chg_en=1, over_vchg=0 at 38009286160 (1970-01-02 00:00:32.825098911 UTC)
<6>[ 60.279554] [email protected],673
<6>[ 60.340620] Release 'boot-time' perf_lock
<6>[ 60.374067] [VIB]recovery(parent:recovery): vibrates 28 msec
<6>[ 60.374342] [ATS][set_vibration][successful]
<6>[ 60.376204] [email protected], 673
<6>[ 60.402266] [VIB]pmic8058_vib_timer_func
<4>[ 65.181989] Thermal: failed to read out thermal zone 1
<6>[ 65.661939] Release 'boot-time' no_halt_lock
<6>[ 66.036725] [BATT] ioctl: battery level update: 38 at 65965951170 (1970-01-02 00:01:00.780970465 UTC)
<6>[ 66.038251] [BATT] ID=2, level=38, vol=3867, temp=393, curr=351, dis_curr=0, chg_src=1, chg_en=1, over_vchg=0 at 65967477049 (1970-01-02 00:01:00.782496343 UTC)
<6>[ 66.218549] pm8058_pwm_led_brightness_set: bank 0 brightness 0 +
<6>[ 66.218671] pm8058_pwm_led_brightness_set: bank 0 brightness 0 -
<6>[ 66.237012] pm8058_pwm_led_brightness_set: bank 1 brightness 1 +
<6>[ 66.237165] pm8058_pwm_led_brightness_set: bank 1 brightness 1 -
<6>[ 66.245191] pm8058_pwm_led_brightness_set: bank 0 brightness 0 +
<6>[ 66.245313] pm8058_pwm_led_brightness_set: bank 0 brightness 0 -
<6>[ 66.253187] pm8058_pwm_led_brightness_set: bank 1 brightness 1 +
<6>[ 66.253370] pm8058_pwm_led_brightness_set: bank 1 brightness 1 -
<6>[ 66.261243] pm8058_pwm_led_brightness_set: bank 0 brightness 0 +
<6>[ 66.261365] pm8058_pwm_led_brightness_set: bank 0 brightness 0 -
<6>[ 66.269269] pm8058_pwm_led_brightness_set: bank 1 brightness 1 +
<6>[ 66.269422] pm8058_pwm_led_brightness_set: bank 1 brightness 1 -
~ #
rzr86 said:
then redownload the rom
check md5 sums
full wipe and flash
Click to expand...
Click to collapse
the init progress is broken