Database Info

[DEV] Discussion about USB-TTL UART JIG

Hey all,
I've created this thread to gather all the info and doubts about UART JIG (also so <I> don't pollute OpenFIMG's thread ).
Readings of interest:
Fun with resistors
Setup in a Nexus S (with pictures)
UART / Serial / JTAG
Odd serial port on Spica (samdroid)
Galaxy S UART JIG & Debugging connector
Developing methods to recover bricks without JTAG
Kernel serial console on i9100
UART Output / Bootloader Hacking / Kernel debugging
Configuration:
Vcc (Pin 1) -> Disconnected.
D- (Pin 2) -> RXD.
D+ (Pin 3) -> TXD.
ID (Pin 4) -> Connected to GND with 523k ohm attached.
GND (Pin 5) -> GND
Baud rate: 115200, 8N1. No control flow.
Boot from the SBL:
Code:
SBL>loadkernel
SBL>loadmodem
SBL>boot
How to get output from kernel.

tom3q said:
<Quote Snipped>.
Click to expand...
Click to collapse
Awesome. Thanks donator!
You've got the uart jig there? Can you test it? (I'm not getting any output.. not [X]BL, nor kernel)

moikop said:
Awesome. Thanks donator!
You've got the uart jig there? Can you test it? (I'm not getting any output.. not [X]BL, nor kernel)
Click to expand...
Click to collapse
This is what I get from the serial port of G3:
Code:
Secondary Boot Loader(SBL)
Built for apollo rev02 by root on Oct 27 2010 17:10:33
Copyright (C) SAMSUNG Corporation 2006-2010
[PAM: ] ++FSR_PAM_Init
[PAM: ] OneNAND physical base address : 0xb0000000
[PAM: ] OneNAND virtual base address : 0xb0000000
[PAM: ] OneNAND nMID=0xec : nDID=0x50
[PAM: ] --FSR_PAM_Init
fsr_bml_load_partition: pi->nNumOfPartEntry = 10
partitions loading success
==== PARTITION INFORMATION ====
ID : IBL & PBL (0x0)
ATTR : RO SLC PREWRITING (0x9002)
FIRST_UNIT : 0
NO_UNITS : 1
===============================
ID : SBL (0x1)
ATTR : RO ENTRYPOINT SLC BOOTLOADING PREWRITING (0xd402)
FIRST_UNIT : 1
NO_UNITS : 5
===============================
ID : PARAM (0x2)
ATTR : RW SLC (0x1001)
FIRST_UNIT : 6
NO_UNITS : 2
===============================
ID : EFS (0x18)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 8
NO_UNITS : 32
===============================
ID : KERNEL (0x4)
ATTR : RO SLC PREWRITING (0x9002)
FIRST_UNIT : 40
NO_UNITS : 30
===============================
ID : FACTORYFS (0x15)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 70
NO_UNITS : 880
===============================
ID : DATAFS (0x16)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 950
NO_UNITS : 810
===============================
ID : CACHE (0x17)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1760
NO_UNITS : 152 (*mismatch* 152 should be 150)
===============================
ID : TEMP (0x3)
ATTR : RW SLC (0x1001)
FIRST_UNIT : 1912
NO_UNITS : 28 (*mismatch* 28 should be 30)
===============================
ID : MODEM (0x5)
ATTR : RO SLC PREWRITING (0x9002)
FIRST_UNIT : 1940
NO_UNITS : 64
===============================
Read image(PARAM) from flash .......
..Done
read 2 units.
Normal Case : MAIN(O) & BACKUP(O)
main: Debug Level Low
RST_STAT = 0x00000004 WAKEUP_STAT = 0x00000000
s5p_fb_info_init start
s5p_fb_info_init end
s5p_fimd_info_init start
s5p_fimd_info_init end
LoadPNG: width:240, height:400, bpp:32, color_type:6, channels:4, rowbytes:960
lcd_gpio_init start
lcd_gpio_init end
lcd_backlight_ctrl start
lcd type: 1
ldi mtpdata: 52 9 11
lcd type is smd
set brightness:0x43
lcd_backlight_ctrl end
SBL:Phone Boot Mode=0
AST_POWERON
usb_download_mode:0
Autoboot (0 seconds) in progress, press any key to stop
AST_ERROR
Autoboot aborted
Type "help" to get a list of commands
SBL>
SBL>
SBL>
SBL> help
Following commands are supported:
* setenv
* savedefault
* saveenv
* printenv
* help
* sec_log
* kernel
* boot
* reset
* nandwrite
* nandread
* nkernel
* readcheck
* savepart
* delpart
* addpart
* showpart
* loadmodem
* loadkernel
* eraseall
* erasepart
* close
* open
* format
* getreg
* setreg
* getadc
* sleep
To get commands help, Type "help <command>"
SBL>
When I let the kernel boot instead of entering the console I get no output from the kernel, possibly because UART switch is being reconfigured to modem somewhere in the kernel, kernel doesn't have serial console enabled or the serial port passed to the kernel in kernel arguments by the bootloader isn't the serial port accessible from microUSB connector.
For reference:
Code:
Secondary Boot Loader(SBL)
Built for apollo rev02 by root on Oct 27 2010 17:10:33
Copyright (C) SAMSUNG Corporation 2006-2010
[PAM: ] ++FSR_PAM_Init
[PAM: ] OneNAND physical base address : 0xb0000000
[PAM: ] OneNAND virtual base address : 0xb0000000
[PAM: ] OneNAND nMID=0xec : nDID=0x50
[PAM: ] --FSR_PAM_Init
fsr_bml_load_partition: pi->nNumOfPartEntry = 10
partitions loading success
==== PARTITION INFORMATION ====
ID : IBL & PBL (0x0)
ATTR : RO SLC PREWRITING (0x9002)
FIRST_UNIT : 0
NO_UNITS : 1
===============================
ID : SBL (0x1)
ATTR : RO ENTRYPOINT SLC BOOTLOADING PREWRITING (0xd402)
FIRST_UNIT : 1
NO_UNITS : 5
===============================
ID : PARAM (0x2)
ATTR : RW SLC (0x1001)
FIRST_UNIT : 6
NO_UNITS : 2
===============================
ID : EFS (0x18)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 8
NO_UNITS : 32
===============================
ID : KERNEL (0x4)
ATTR : RO SLC PREWRITING (0x9002)
FIRST_UNIT : 40
NO_UNITS : 30
===============================
ID : FACTORYFS (0x15)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 70
NO_UNITS : 880
===============================
ID : DATAFS (0x16)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 950
NO_UNITS : 810
===============================
ID : CACHE (0x17)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1760
NO_UNITS : 152 (*mismatch* 152 should be 150)
===============================
ID : TEMP (0x3)
ATTR : RW SLC (0x1001)
FIRST_UNIT : 1912
NO_UNITS : 28 (*mismatch* 28 should be 30)
===============================
ID : MODEM (0x5)
ATTR : RO SLC PREWRITING (0x9002)
FIRST_UNIT : 1940
NO_UNITS : 64
===============================
Read image(PARAM) from flash .......
..Done
read 2 units.
Normal Case : MAIN(O) & BACKUP(O)
main: Debug Level Low
RST_STAT = 0x00000004 WAKEUP_STAT = 0x00000000
s5p_fb_info_init start
s5p_fb_info_init end
s5p_fimd_info_init start
s5p_fimd_info_init end
LoadPNG: width:240, height:400, bpp:32, color_type:6, channels:4, rowbytes:960
lcd_gpio_init start
lcd_gpio_init end
lcd_backlight_ctrl start
lcd type: 1
ldi mtpdata: 52 9 11
lcd type is smd
set brightness:0x43
lcd_backlight_ctrl end
SBL:Phone Boot Mode=0
AST_POWERON
usb_download_mode:0
Autoboot (0 seconds) in progress, press any key to stop
FOTA Check Bit
Read BML page=1e4ff, NumPgs=1
FOTA Check Bit (0x0)
Load Partion idx = (4)
..............................done
Kernel read success from kernel partition
setKernelParam: setting param.serialnr=3930c0cf08x 0x159100ec
setKernelParam: setting param.board_rev=0x2
setKernelParam: setting param.cmdline=console=ttySAC1,115200 loglevel=4 version=Sbl(1.0.0) 2010-10-27 17:10:33
Starting kernel at 0x22000000...

moikop said:
Awesome. I think ttySAC1 is defined as s3c2410_serial1 in the kernel. And maybe you'll have to change SWITCH_SEL from the sbl console (from 65 to 6543).
I still don't understand why all I get this � weird character :/
Vcc connected to 3.3v, 150k ohm (though tried with 619k too) resistor and baud rate 115200 8N1, right?
Click to expand...
Click to collapse
Maybe something wrong with your level converter?
Also, if I decoded color codes of resistors correctly, I have 522k ohms connected between GND and ID pins (two 1M connected in parallel and additional 22k after them).
Edit: Would make sense, as according to http://forum.xda-developers.com/showthread.php?t=820275 it would be
Code:
RID_FM_BOOT_OFF_UART, /* 1 1 1 0 0 523K Factory Mode Boot OFF-UART */

tom3q said:
Maybe something wrong with your level converter?
Also, if I decoded color codes of resistors correctly, I have 522k ohms connected between GND and ID pins (two 1M connected in parallel and additional 22k after them).
Edit: Would make sense, as according to http://forum.xda-developers.com/showthread.php?t=820275 it would be
Code:
RID_FM_BOOT_OFF_UART, /* 1 1 1 0 0 523K Factory Mode Boot OFF-UART */
Click to expand...
Click to collapse
Tried with both, 522k & 523k (just in case) and still the same.. So it's gotta be my level converter... that's weird :S

moikop said:
Tried with both, 522k & 523k (just in case) and still the same.. So it's gotta be my level converter... that's weird :S
Click to expand...
Click to collapse
Just for reference, my level converter: http://translate.google.com/transla...unikacja-przez-usb---modul-em212.html&act=url
EDIT: Maybe we should create new topic for discussion on such things?

tom3q said:
Just for reference, my level converter: http://translate.google.com/transla...unikacja-przez-usb---modul-em212.html&act=url
EDIT: Maybe we should create new topic for discussion on such things?
Click to expand...
Click to collapse
You're right. So here it is.
I don't see why my level converter wouldn't work, since it supports the right voltage, baud rate, etc.
mmm, some weird idea: what's you're bootloader version? (I mean from which release). I'm thinking maybe the bootloader version is my problem? (since I have Samsungs latest installed)

moikop said:
You're right. So here it is.
I don't see why my level converter wouldn't work, since it supports the right voltage, baud rate, etc.
mmm, some weird idea: what's you're bootloader version? (I mean from which release). I'm thinking maybe the bootloader version is my problem? (since I have Samsungs latest installed)
Click to expand...
Click to collapse
I don't know the exact version as it was already on the phone as I got it. The only thing saying a bit about the version is its output:
Code:
Built for apollo rev02 by root on Oct 27 2010 17:10:33
Have you tried different baud rates? Common ones other than 115200 are 9600 and 38400.
Also this thread would become a bit more informative if all the posts on this topic would get moved here from OpenFIMG thread.
EDIT: Also make sure that ground signal is properly connected, otherwise the converter might not recognize voltage levels correctly. What's exactly your connection layout? I have only 4 lines wired to the microUSB connector, RX, TX, GND and ID with VCC left unconnected.

tom3q said:
I don't know the exact version as it was already on the phone as I got it. The only thing saying a bit about the version is its output:
Code:
Built for apollo rev02 by root on Oct 27 2010 17:10:33
Click to expand...
Click to collapse
mmm.. I have JPU, so my bootloader is at least from 2011..
tom3q said:
Have you tried different baud rates? Common ones other than 115200 are 9600 and 38400.
Click to expand...
Click to collapse
Tried with those 3. With 9600 and 38400 I don't get anything, when with 115200 I get the "?" character.
tom3q said:
Also this thread would become a bit more informative if all the posts on this topic would get moved here from OpenFIMG thread.
Click to expand...
Click to collapse
I'll contact a mod and see what can be done.
tom3q said:
EDIT: Also make sure that ground signal is properly connected, otherwise the converter might not recognize voltage levels correctly. What's exactly your connection layout? I have only 4 lines wired to the microUSB connector, RX, TX, GND and ID with VCC left unconnected.
Click to expand...
Click to collapse
Double checked my GND connection and is ok. My layout is the following:
VCC -> 3.3v
Tx & Rx with their corresponding pins.
ID connected to GND with 523k ohm in between
and GND connected to GND.

Could you try without VCC connected?
I really don't think that Samsung would disable bootloader console used in service centers for phone diagnostics...

tom3q said:
Could you try without VCC connected?
Click to expand...
Click to collapse
Exact same result.
With GND disconected also same result.
If Tx is disconnected there's no output (obviously). So a badly soldered/connected Pin2 can be discarded.
Checked Rx too, So a badly soldered/connected Pin3 can be discarded as well..
tom3q said:
I really don't think that Samsung would disable bootloader console used in service centers for phone diagnostics...
Click to expand...
Click to collapse
You must be right..
Edit: I changed pin2 & pin3 (now Pin2 is to Rx and Pin3 to Tx). Also connected GND (but left vcc disconnected as you) and got it working
Thanks for the help!

moikop said:
Edit: I changed pin2 & pin3 (now Pin2 is to Rx and Pin3 to Tx). Also connected GND (but left vcc disconnected as you) and got it working
Thanks for the help!
Click to expand...
Click to collapse
So what good is this that you are doing? Benefits etc.
And are we meant to be doing something similar to make phone work better?
Sent from the Persian Sphinx's private Galaxy

PersianSphinx said:
So what good is this that you are doing? Benefits etc.
And are we meant to be doing something similar to make phone work better?
Sent from the Persian Sphinx's private Galaxy
Click to expand...
Click to collapse
With this, we can get into the SBL console, get information about kernel panics (not yet) and this will help us debug kernel ports, drivers ports, etc.
And no. This would be useless for a normal user. Unless that (s)he wants to make a Download JIG (to get into download mode without having to use the three-button combo). In that case, a different resistor value (301k) is needed (and no level converter, of cource )

@PersianSphinx
This wud resurrect a hard bricked phone...this JTAG thing
Sent from my GT-I9100 using Tapatalk

Orr.Penn.18 said:
@PersianSphinx
This wud resurrect a hard bricked phone...this JTAG thing
Sent from my GT-I9100 using Tapatalk
Click to expand...
Click to collapse
This is not JTAG.

moikop said:
Edit: I changed pin2 & pin3 (now Pin2 is to Rx and Pin3 to Tx). Also connected GND (but left vcc disconnected as you) and got it working
Thanks for the help!
Click to expand...
Click to collapse
This is common fault people are doing - phone Rxd must be connected to converter Txd and vice versa.

Kernel output:
To get kernel output, all you need to do is:
Code:
setenv SWITCH_SEL 6543
And then boot normally from SBL.
To make this setting permanent:
Code:
setenv SWITCH_SEL 6543
saveenv
Result:
Code:
SBL> boot
setKernelParam: setting param.serialnr=3830f5ff08x 0xd44100ec
setKernelParam: setting param.board_rev=0x2
setKernelParam: setting param.cmdline=console=ttySAC1,115200 version=Sbl(1.0.0)2
Starting kernel at 0x22000000...
Uncompressing Linux.............................................................
<6>Initializing cgroup subsys cpu
<5>Linux version 2.6.32.9 ([email protected]) (gcc version 4.5.2 (Sourcery G++ Lite2
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv6TEJ), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: GT-I5800
Memory policy: ECC disabled, Data cache writeback
<7>On node 0 totalpages: 65536
<7>free_area_init_node: node 0, pgdat c0aa7640, node_mem_map c0c3e000
<7> Normal zone: 512 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 65024 pages, LIFO batch:15
<7>On node 1 totalpages: 0
<7>free_area_init_node: node 1, pgdat c0aa7cf8, node_mem_map c0e47800
<4> Normal zone: 1 pages exceeds realsize 0
<7>On node 2 totalpages: 0
<7>free_area_init_node: node 2, pgdat c0aa83b0, node_mem_map c0e4f880
<4> Normal zone: 1 pages exceeds realsize 0
<7>On node 3 totalpages: 0
<7>free_area_init_node: node 3, pgdat c0aa8a68, node_mem_map c0e57900
<4> Normal zone: 1 pages exceeds realsize 0
CPU S5P6442 (id 0xababab00)
<7>s5p6442_init_clocks: initialising clocks
<6>S3C24XX Clocks, (c) 2004 Simtec Electronics
<7>s5p6442_setup_clocks: registering clocks
<6>mout_apll: source is fout_apll (1), rate is 667000000
<6>mout_epll: source is fout_epll (1), rate is 48000000
<6>mout_mpll: source is mpll (1), rate is 166000000
<6>mout_d0: source is mout_mpll (0), rate is 166000000
<6>mout_d1: source is mout_mpll (0), rate is 166000000
<6>mout_d0sync: source is mout_d0 (0), rate is 166000000
<6>mout_d1sync: source is mout_d1 (0), rate is 166000000
<6>mmc_bus: source is mout_mpll (6), rate is 83000000
<6>mmc_bus: source is mout_mpll (6), rate is 83000000
<6>mmc_bus: source is mout_mpll (6), rate is 83000000
<6>sclk_uart: source is mout_mpll (6), rate is 166000000
<6>sclk_uart: source is mout_mpll (6), rate is 166000000
<6>sclk_uart: source is mout_mpll (6), rate is 83000000
<6>spi-bus: source is mout_epll (7), rate is 48000000
<6>sclk_lcd: source is mout_mpll (6), rate is 166000000
<6>sclk_cam0: source is mout_mpll (6), rate is 166000000
<6>sclk_cam1: source is mout_mpll (6), rate is 166000000
<6>lclk_fimc: source is mout_mpll (6), rate is 166000000
<6>lclk_fimc: source is mout_mpll (6), rate is 166000000
<6>lclk_fimc: source is mout_mpll (6), rate is 166000000
<6>clk_g2d: source is mout_mpll (1), rate is 166000000
<6>i2sclk: source is i2smain_clk (0), rate is 48000000
<6>audss_hclk: source is i2smain_clk (0), rate is 48000000
<6>i2smain_clk: source is fout_epll (1), rate is 48000000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
<5>Kernel command line: console=ttySAC1,115200 version=Sbl(1.0.0) 2011-05-27 142
<6>PID hash table entries: 1024 (order: 0, 4096 bytes)
<6>Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>Memory: 256MB = 256MB total
<5>Memory: 247040KB available (7488K code, 1639K data, 2972K init, 0K highmem)
<6>SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=4
<6>NR_IRQS:287
<7>s5p64xx_init_irq: initialising interrupts
<6>VIC @f4000000: id 0x00041192, vendor 0x41
<6>VIC @f4010000: id 0x00041192, vendor 0x41
<6>VIC @f4020000: id 0x00041192, vendor 0x41
<3>vic_pm_register: too few VICs, increase CONFIG_ARM_VIC_NR
Console: colour dummy device 80x30
s3c24xx_serial_initconsole
s3c24xx_serial_init_ports: initialising ports...
s3c24xx_serial_init_port: port=c0ad8a60, platdev=c0aabb10
s3c24xx_serial_init_port: c0ad8a60 (hw 0)...
...

moikop said:
To get kernel output, all you need to do is:
Code:
setenv SWITCH_SEL 6543
And then boot normally from SBL.
To make this setting permanent:
Code:
setenv SWITCH_SEL 6543
saveenv
Result:
Code:
SBL> boot
setKernelParam: setting param.serialnr=3830f5ff08x 0xd44100ec
setKernelParam: setting param.board_rev=0x2
setKernelParam: setting param.cmdline=console=ttySAC1,115200 version=Sbl(1.0.0)2
Starting kernel at 0x22000000...
Uncompressing Linux.............................................................
<6>Initializing cgroup subsys cpu
<5>Linux version 2.6.32.9 ([email protected]) (gcc version 4.5.2 (Sourcery G++ Lite2
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv6TEJ), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: GT-I5800
Memory policy: ECC disabled, Data cache writeback
<7>On node 0 totalpages: 65536
<7>free_area_init_node: node 0, pgdat c0aa7640, node_mem_map c0c3e000
<7> Normal zone: 512 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 65024 pages, LIFO batch:15
<7>On node 1 totalpages: 0
<7>free_area_init_node: node 1, pgdat c0aa7cf8, node_mem_map c0e47800
<4> Normal zone: 1 pages exceeds realsize 0
<7>On node 2 totalpages: 0
<7>free_area_init_node: node 2, pgdat c0aa83b0, node_mem_map c0e4f880
<4> Normal zone: 1 pages exceeds realsize 0
<7>On node 3 totalpages: 0
<7>free_area_init_node: node 3, pgdat c0aa8a68, node_mem_map c0e57900
<4> Normal zone: 1 pages exceeds realsize 0
CPU S5P6442 (id 0xababab00)
<7>s5p6442_init_clocks: initialising clocks
<6>S3C24XX Clocks, (c) 2004 Simtec Electronics
<7>s5p6442_setup_clocks: registering clocks
<6>mout_apll: source is fout_apll (1), rate is 667000000
<6>mout_epll: source is fout_epll (1), rate is 48000000
<6>mout_mpll: source is mpll (1), rate is 166000000
<6>mout_d0: source is mout_mpll (0), rate is 166000000
<6>mout_d1: source is mout_mpll (0), rate is 166000000
<6>mout_d0sync: source is mout_d0 (0), rate is 166000000
<6>mout_d1sync: source is mout_d1 (0), rate is 166000000
<6>mmc_bus: source is mout_mpll (6), rate is 83000000
<6>mmc_bus: source is mout_mpll (6), rate is 83000000
<6>mmc_bus: source is mout_mpll (6), rate is 83000000
<6>sclk_uart: source is mout_mpll (6), rate is 166000000
<6>sclk_uart: source is mout_mpll (6), rate is 166000000
<6>sclk_uart: source is mout_mpll (6), rate is 83000000
<6>spi-bus: source is mout_epll (7), rate is 48000000
<6>sclk_lcd: source is mout_mpll (6), rate is 166000000
<6>sclk_cam0: source is mout_mpll (6), rate is 166000000
<6>sclk_cam1: source is mout_mpll (6), rate is 166000000
<6>lclk_fimc: source is mout_mpll (6), rate is 166000000
<6>lclk_fimc: source is mout_mpll (6), rate is 166000000
<6>lclk_fimc: source is mout_mpll (6), rate is 166000000
<6>clk_g2d: source is mout_mpll (1), rate is 166000000
<6>i2sclk: source is i2smain_clk (0), rate is 48000000
<6>audss_hclk: source is i2smain_clk (0), rate is 48000000
<6>i2smain_clk: source is fout_epll (1), rate is 48000000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
<5>Kernel command line: console=ttySAC1,115200 version=Sbl(1.0.0) 2011-05-27 142
<6>PID hash table entries: 1024 (order: 0, 4096 bytes)
<6>Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>Memory: 256MB = 256MB total
<5>Memory: 247040KB available (7488K code, 1639K data, 2972K init, 0K highmem)
<6>SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=4
<6>NR_IRQS:287
<7>s5p64xx_init_irq: initialising interrupts
<6>VIC @f4000000: id 0x00041192, vendor 0x41
<6>VIC @f4010000: id 0x00041192, vendor 0x41
<6>VIC @f4020000: id 0x00041192, vendor 0x41
<3>vic_pm_register: too few VICs, increase CONFIG_ARM_VIC_NR
Console: colour dummy device 80x30
s3c24xx_serial_initconsole
s3c24xx_serial_init_ports: initialising ports...
s3c24xx_serial_init_port: port=c0ad8a60, platdev=c0aabb10
s3c24xx_serial_init_port: c0ad8a60 (hw 0)...
...
Click to expand...
Click to collapse
Yep, on Spica setenv SWITCH_SEL 3 is enough. According to SBL sources, bit 0 selects USB switch mode and bit 1 selects UART swtich mode.

Orr.Penn.18 said:
@PersianSphinx
This wud resurrect a hard bricked phone...this JTAG thing
Sent from my GT-I9100 using Tapatalk
Click to expand...
Click to collapse
this is not jtag.... this is UART...this gives us info on what went wrong when the phone dosnt boot up properly when devs are testing new things.

I just received my level converter and it's working fine, I can get SBL logs.
But how to access the SBL prompt ?
I tried with some key combinaison but nothing work :/

[PROJECT] Kernel 3.4.x For Galaxy 3

This thread to collaborate all efforts towards porting kernel 3.4.x on to the Galaxy 3. If any developers wish to help then please let me know and I will add you to the SG3 group on Github (provided you have proven yourself capable of helping by forking the repository and submitting a pull request of changes you have made - I won't just add people if they are 'learning how to develop for Linux').
Changelog
https://github.com/sg3/android_kernel_samsung_s5p6442/commits/s5p6442-3.4
I chose the Github commit system to be the changelog as there are so many things going on at once it would be impossible to keep up with, and I cannot be assed explaining it. If you don't understand then ask, but please don't ask EVERYTHING. Most of the answers will be 'It just does'.
I am trying to follow the standard process for committing to GIT by doing 's5p6442: change' or 'apollo: change' so it is easier to see what is being fixed and why we are changing it so people reviewing code have an easier job. I expect other developers to follow this as well. Pull requests made that do not follow this naming convention will be rejected.
Source Code
Source: https://github.com/sg3/android_kernel_samsung_s5p6442
Members
The following members already have full read/write access to the repository:
cdesai
hillbeast <- has UART
marcellusbe <- has UART
moikop <- has UART
tom3q <- has UART
As you can see I also listed who has UART (that I currently know of). If you also have UART then let me know and I shall add it to the list. Having UART will be a huge help as it means we can see what is going on.
Why Do We Need Kernel 3.
Easier updating the kernel to add security and performance boosts from mainline Linux kernels
More support for new versions of Android
Android 4.0 was built upon Linux Kernel 3.0.x and therefore expects kernel 3.0s APIs
Faster, more secure system
NO SAMSUNG MORONIC CODE
Because it's just better
Please let me know if you are interested (able to) in helping this cause. Please don't put your hand up if you can't dedicate your phone to this. This will result in your phone being out of action quite a lot while we are testing, and if you need your phone 24/7 then you're going to need to keep flashing back. You will also NEED ODIN. Flashing from CWM is not an option.

Status
What is working
Basic mach-code for s5p6442
Serial/UART
CPU clock and most clock sources
Most mach addresses/IRQs/GPIOs
Kernel init
initramfs init
MTD/OneNAND
GPIO
Screen/Framebuffer
Keypad/buttons
Reboot
Real time clock
I2C over GPIO
HSMMC
What needs to be done
Samsung S3C I2C
Reboot modes
I2S
SDIO
Device Drivers (WiFi, Audio, sensors, etc)
UART Dump
Code:
Starting kernel at 0x22000000...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.27+ ([email protected]) (gcc version 4.6.2 20120613 (release) [ARM/embedded-4_6-branch revision 188521] (GNU Tools for ARM Embedded Processors) ) #Test Sun Jan 13 20:44:01 NZDT 2013
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv6TEJ), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: APOLLO
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU S5P6442 (id 0x36442000)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] s5p6442_setup_clocks: clkdiv0 = 10100000
[ 0.000000] S5P6442: PLL settings, A=667000000, M=166000000, E=48000000
[ 0.000000] mout_apll: source is fout_apll (1), rate is 667000000
[ 0.000000] mout_mpll: source is fout_mpll (1), rate is 166000000
[ 0.000000] mout_epll: source is fout_epll (1), rate is 48000000
[ 0.000000] mout_arm: source is mout_apll (1), rate is 667000000
[ 0.000000] mout_d0: source is mout_mpll (1), rate is 166000000
[ 0.000000] mout_d0sync: source is mout_d0 (1), rate is 166000000
[ 0.000000] mout_d1: source is mout_mpll (1), rate is 166000000
[ 0.000000] mout_d1sync: source is mout_d1 (1), rate is 166000000
[ 0.000000] sclk_mfc: source is mout_mpll (0), rate is 166000000
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 83000000
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 83000000
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 83000000
[ 0.000000] dout_a2m: source is fout_apll (1), rate is 667000000
[ 0.000000] dout_apll: source is mout_apll (1), rate is 667000000
[ 0.000000] hclkd1: source is mout_d1 (1), rate is 166000000
[ 0.000000] hclkd0: source is mout_d0 (1), rate is 166000000
[ 0.000000] pclkd0: source is mout_d0 (1), rate is 83000000
[ 0.000000] pclkd1: source is mout_d1 (1), rate is 83000000
[ 0.000000] S5P6442: HCLKD0=166000000, HCLKD1=166000000, PCLKD0=83000000, PCLKD1=83000000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 84832
[ 0.000000] Kernel command line: console=ttySAC1,115200 version=Sbl(1.0.0) 2010-10-27 17:10:33
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 1212416 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 256MB 80MB = 336MB total
[ 0.000000] Memory: 324804k/324804k available, 19260k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe5800000 - 0xff000000 ( 408 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe5000000 ( 592 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0995db4 (9784 kB)
[ 0.000000] .init : 0xc0996000 - 0xc0c29000 (2636 kB)
[ 0.000000] .data : 0xc0c2a000 - 0xc0cae688 ( 530 kB)
[ 0.000000] .bss : 0xc0cae6ac - 0xc0e8bc38 (1910 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:208
[ 0.000000] VIC @f6000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @f6010000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @f6020000: id 0x00041192, vendor 0x41
[ 0.000000] vic_register: too few VICs, increase CONFIG_ARM_VIC_NR
[ 0.000000] sched_clock: 32 bits at 41MHz, resolution 24ns, wraps every 103493ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000363] Calibrating delay loop... 663.55 BogoMIPS (lpj=1658880)
[ 0.060015] pid_max: default: 32768 minimum: 301
[ 0.060273] Security Framework initialized
[ 0.060345] AppArmor: AppArmor initialized
[ 0.060775] Mount-cache hash table entries: 512
[ 0.061926] Initializing cgroup subsys cpuacct
[ 0.061959] Initializing cgroup subsys memory
[ 0.062041] Initializing cgroup subsys devices
[ 0.062064] Initializing cgroup subsys freezer
[ 0.062082] Initializing cgroup subsys blkio
[ 0.062124] Initializing cgroup subsys perf_event
[ 0.062325] CPU: Testing write buffer coherency: ok
[ 0.062417] ftrace: allocating 24113 entries in 71 pages
[ 0.256329] hw perfevents: enabled with v6 PMU driver, 3 counters available
[ 0.256470] Setting up static identity map for 0x20652280 - 0x206522dc
[ 0.259465] devtmpfs: initialized
[ 0.261208] EVM: security.selinux
[ 0.261230] EVM: security.SMACK64
[ 0.261243] EVM: security.capability
[ 0.262295] gpiochip_add: registered GPIOs 0 to 7 on device: GPA0
[ 0.262327] gpiochip_add: registered GPIOs 9 to 10 on device: GPA1
[ 0.262348] gpiochip_add: registered GPIOs 12 to 15 on device: GPB
[ 0.262366] gpiochip_add: registered GPIOs 17 to 21 on device: GPC0
[ 0.262384] gpiochip_add: registered GPIOs 23 to 27 on device: GPC1
[ 0.262402] gpiochip_add: registered GPIOs 29 to 30 on device: GPD0
[ 0.262420] gpiochip_add: registered GPIOs 32 to 37 on device: GPD1
[ 0.262438] gpiochip_add: registered GPIOs 39 to 46 on device: GPE0
[ 0.262457] gpiochip_add: registered GPIOs 48 to 52 on device: GPE1
[ 0.262475] gpiochip_add: registered GPIOs 54 to 61 on device: GPF0
[ 0.262494] gpiochip_add: registered GPIOs 63 to 70 on device: GPF1
[ 0.262512] gpiochip_add: registered GPIOs 72 to 79 on device: GPF2
[ 0.262531] gpiochip_add: registered GPIOs 81 to 86 on device: GPF3
[ 0.262549] gpiochip_add: registered GPIOs 88 to 94 on device: GPG0
[ 0.262568] gpiochip_add: registered GPIOs 96 to 102 on device: GPG1
[ 0.262587] gpiochip_add: registered GPIOs 104 to 110 on device: GPG2
[ 0.262606] gpiochip_add: registered GPIOs 148 to 155 on device: GPJ0
[ 0.262624] gpiochip_add: registered GPIOs 157 to 162 on device: GPJ1
[ 0.262644] gpiochip_add: registered GPIOs 164 to 171 on device: GPJ2
[ 0.262664] gpiochip_add: registered GPIOs 173 to 180 on device: GPJ3
[ 0.262683] gpiochip_add: registered GPIOs 182 to 186 on device: GPJ4
[ 0.262702] gpiochip_add: registered GPIOs 188 to 195 on device: MP01
[ 0.262721] gpiochip_add: registered GPIOs 197 to 200 on device: MP02
[ 0.262739] gpiochip_add: registered GPIOs 202 to 206 on device: MP03
[ 0.262758] gpiochip_add: registered GPIOs 208 to 215 on device: MP04
[ 0.262777] gpiochip_add: registered GPIOs 217 to 224 on device: MP05
[ 0.262796] gpiochip_add: registered GPIOs 226 to 233 on device: MP06
[ 0.262815] gpiochip_add: registered GPIOs 235 to 242 on device: MP07
[ 0.262834] gpiochip_add: registered GPIOs 244 to 251 on device: MP10
[ 0.262853] gpiochip_add: registered GPIOs 112 to 119 on device: GPH0
[ 0.262872] gpiochip_add: registered GPIOs 121 to 128 on device: GPH1
[ 0.262891] gpiochip_add: registered GPIOs 130 to 137 on device: GPH2
[ 0.262910] gpiochip_add: registered GPIOs 139 to 146 on device: GPH3
[ 0.263470] dummy:
[ 0.264100] NET: Registered protocol family 16
[ 0.275100] apollo_machine_init : hw_rev_pin=0x0
[ 0.275128] apollo_machine_init : bootmode=0x0
[ 0.275146] apollo_machine_init : lcd_id=1
[ 0.275161] apollo_machine_init : uart_sel=1
[ 0.275216] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.275237] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.275523] S5P6442: Initializing architecture
[ 0.291494] bio: create slab <bio-0> at 0
[ 0.293402] SCSI subsystem initialized
[ 0.294000] usbcore: registered new interface driver usbfs
[ 0.294214] usbcore: registered new interface driver hub
[ 0.294630] usbcore: registered new device driver usb
[ 0.295434] i2c i2c-3: Not I2C compliant: can't read SCL
[ 0.295462] i2c i2c-3: Bus may be unreliable
[ 0.295487] i2c-gpio i2c-gpio.3: using pins 220 (SDA) and 219 (SCL, no clock stretching)
[ 0.296287] max8998 4-0066: No interrupt specified, no interrupts
[ 0.300785] VALIVE_1.1V: 1100 mV
[ 0.302519] VUSB+MIPI_1.1V: 1100 mV
[ 0.304283] VDAC_3.3V: 3300 mV
[ 0.306136] VTF_2.8V: 2800 mV
[ 0.307889] VCC_3.3V: 3300 mV
[ 0.310548] VLCD_1.8V: 1800 mV
[ 0.312288] VUSB+VADC_3.3V: 3300 mV
[ 0.314100] VCC+VCAM_2.8V: 2800 mV
[ 0.316692] VPLL_1.1V: 1100 mV
[ 0.318393] CAM_IO_2.8V: 2800 mV
[ 0.320204] CAM_ISP_1.2V: 1200 mV
[ 0.321958] CAM_A_2.8V: 2800 mV
[ 0.323682] CAM_CIF_1.8V: 1800 mV
[ 0.325508] CAM_AF_3.3V: 3300 mV
[ 0.327243] VMIPI_1.8V: 1800 mV
[ 0.329838] VCC_3.0V_LCD: 3000 mV
[ 0.331270] VARM_1.2V: 1200 mV
[ 0.332645] VINT_1.2V: 1200 mV
[ 0.334014] VCC_1.8V: 1800 mV
[ 0.336329] CAM_CORE_1.2V: 1200 mV
[ 0.337442] i2c-gpio i2c-gpio.4: using pins 182 (SDA) and 185 (SCL)
[ 0.337761] i2c-gpio i2c-gpio.7: using pins 153 (SDA) and 152 (SCL)
[ 0.338087] i2c-gpio i2c-gpio.8: using pins 34 (SDA) and 35 (SCL)
[ 0.338390] i2c-gpio i2c-gpio.9: using pins 178 (SDA) and 179 (SCL)
[ 0.338704] s3c-i2c s3c2410-i2c.0: slave address 0x10
[ 0.338750] s3c-i2c s3c2410-i2c.0: bus frequency set to 81 KHz
[ 0.338797] s3c-i2c s3c2410-i2c.0: cannot claim IRQ 78
[ 0.338850] s3c-i2c: probe of s3c2410-i2c.0 failed with error -38
[ 0.339021] s3c-i2c s3c2410-i2c.1: slave address 0x10
[ 0.339066] s3c-i2c s3c2410-i2c.1: bus frequency set to 81 KHz
[ 0.339106] s3c-i2c s3c2410-i2c.1: cannot claim IRQ 109
[ 0.339157] s3c-i2c: probe of s3c2410-i2c.1 failed with error -22
[ 0.339322] s3c-i2c s3c2410-i2c.2: slave address 0x10
[ 0.339364] s3c-i2c s3c2410-i2c.2: bus frequency set to 81 KHz
[ 0.339682] s3c-i2c s3c2410-i2c.2: i2c-2: S3C I2C adapter
[ 0.339810] Linux video capture interface: v2.00
[ 0.340585] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.341666] Bluetooth: Core ver 2.16
[ 0.341800] NET: Registered protocol family 31
[ 0.341822] Bluetooth: HCI device and connection manager initialized
[ 0.341843] Bluetooth: HCI socket layer initialized
[ 0.341860] Bluetooth: L2CAP socket layer initialized
[ 0.341920] Bluetooth: SCO socket layer initialized
[ 0.341941] NetLabel: Initializing
[ 0.341955] NetLabel: domain hash size = 128
[ 0.341967] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.342112] NetLabel: unlabeled traffic allowed by default
[ 0.342849] Switching to clocksource s5p_clocksource_timer
[ 0.379780] AppArmor: AppArmor Filesystem Enabled
[ 0.409043] NET: Registered protocol family 2
[ 0.409412] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.410301] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.411581] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.412212] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.412232] TCP: reno registered
[ 0.412256] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.412319] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.412878] NET: Registered protocol family 1
[ 0.413878] RPC: Registered named UNIX socket transport module.
[ 0.413908] RPC: Registered udp transport module.
[ 0.413924] RPC: Registered tcp transport module.
[ 0.413940] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.313502] audit: initializing netlink socket (disabled)
[ 2.313597] type=2000 audit(2.175:1): initialized
[ 2.518638] VFS: Disk quotas dquot_6.5.2
[ 2.519085] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.523547] NFS: Registering the id_resolver key type
[ 2.526646] fuse init (API version 7.18)
[ 2.527762] msgmni has been set to 634
[ 2.535433] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.535935] io scheduler noop registered
[ 2.535965] io scheduler deadline registered
[ 2.536070] io scheduler cfq registered (default)
[ 2.545209] Console: switching to colour frame buffer device 30x25
[ 2.549050] s3c-fb s3c-fb: window 0: fb
[ 2.549647] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 2.564511] s5pv210-uart.0: ttySAC0 at MMIO 0xec000000 (irq = 74) is a S3C6400/10
[ 2.565120] s5pv210-uart.1: ttySAC1 at MMIO 0xec000400 (irq = 75) is a S3C6400/10
[ 3.688673] console [ttySAC1] enabled
[ 3.692714] s5pv210-uart.2: ttySAC2 at MMIO 0xec000800 (irq = 76) is a S3C6400/10
[ 3.701079] ramoops: platform device not found, using module parameters
[ 3.706799] ramoops: The memory size and the record size must be non-zero
[ 3.713399] ramoops: probe of ramoops failed with error -22
[ 3.735283] brd: module loaded
[ 3.744057] loop: module loaded
[ 3.745830] nbd: registered device at major 43
[ 3.762773] i2c-core: driver [fsa9480] using legacy suspend method
[ 3.763421] i2c-core: driver [fsa9480] using legacy resume method
[ 3.770606] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 3.776125] =================================================================
[ 3.783321] Samsung OneNAND Driver (AUDI).
[ 3.787406] =================================================================
[ 3.794866] OneNAND: Clock gating is enabled.
[ 3.799181] Muxed OneNAND 512MB 1.8V 16-bit (0x50)
[ 3.803964] OneNAND version = 0x013e
[ 3.809584] Scanning device for bad blocks
[ 3.852229] onenand_bbt_wait: ecc error = 0x0001, controller error 0x0400
[ 3.853463] OneNAND eraseblock 320 is an initial bad block
[ 4.077529] OneNAND eraseblock 2047 is an initial bad block
[ 4.079391] Creating 8 MTD partitions on "s5p-onenand":
[ 4.082775] 0x000000a00000-0x000001180000 : "boot"
[ 4.090109] 0x000001180000-0x00000ed80000 : "system"
[ 4.095512] 0x00000ed80000-0x00001b800000 : "userdata"
[ 4.100622] 0x00001b800000-0x00001de00000 : "cache"
[ 4.105243] 0x00001de00000-0x00001f500000 : "efs"
[ 4.110030] 0x00001f500000-0x00001ffc0000 : "reservoir"
[ 4.115311] 0x00001ffc0000-0x000020000000 : "dgs"
[ 4.120079] 0x000000180000-0x000000200000 : "param"
[ 4.129186] Fixed MDIO Bus: probed
[ 4.129479] tun: Universal TUN/TAP device driver, 1.6
[ 4.132039] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 4.138886] PPP generic driver version 2.4.2
[ 4.143197] PPP BSD Compression module registered
[ 4.147386] PPP Deflate Compression module registered
[ 4.155764] PPP MPPE Compression module registered
[ 4.157358] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.165883] mousedev: PS/2 mouse device common for all mice
[ 4.170690] input: samsung-keypad as /devices/platform/samsung-keypad/input/input0
[ 4.183677] max8998-rtc max8998-rtc: rtc core: registered max8998-rtc as rtc0
[ 4.185222] max8998-rtc max8998-rtc: Failed to request alarm IRQ: 9: -22
[ 4.192094] max8998-rtc max8998-rtc: RTC CHIP NAME: max8998-rtc
[ 4.198341] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 4.204232] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc1
[ 4.209837] s3c-rtc s3c64xx-rtc: warning: invalid RTC value so initializing it
[ 4.217293] i2c /dev entries driver
[ 4.223542] lirc_dev: IR Remote Control driver registered, major 252
[ 4.227104] IR NEC protocol handler initialized
[ 4.231789] IR RC5(x) protocol handler initialized
[ 4.236611] IR RC6 protocol handler initialized
[ 4.241188] IR JVC protocol handler initialized
[ 4.245773] IR Sony protocol handler initialized
[ 4.250448] IR RC5 (streamzap) protocol handler initialized
[ 4.256091] IR SANYO protocol handler initialized
[ 4.260894] IR MCE Keyboard/mouse protocol handler initialized
[ 4.266831] IR LIRC bridge handler initialized
[ 4.271884] vivi-000: V4L2 device registered as video0
[ 4.276490] Video Technology Magazine Virtual Video Capture Board ver 0.8.1 successfully loaded.
[ 4.286115] m2m-testdev m2m-testdev.0: mem2mem-testdevDevice registered as /dev/video1
[ 4.293614] S5P JPEG V4L2 Driver, (c) 2011 Samsung Electronics
[ 4.299987] s5p-jpeg s5p-jpeg.0: encoder device registered as /dev/video2
[ 4.306631] s5p-jpeg s5p-jpeg.0: decoder device registered as /dev/video3
[ 4.313092] s5p-jpeg s5p-jpeg.0: Samsung S5P JPEG codec
[ 4.319104] s5p-mfc s5p-mfc: decoder registered as /dev/video4
[ 4.324735] s5p-mfc s5p-mfc: encoder registered as /dev/video5
[ 4.331964] device-mapper: uevent: version 1.0.3
[ 4.335859] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
[ 4.344756] device-mapper: multipath: version 1.3.0 loaded
[ 4.349027] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 4.355582] device-mapper: multipath queue-length: version 0.1.0 loaded
[ 4.362272] device-mapper: multipath service-time: version 0.2.0 loaded
[ 4.369166] Bluetooth: HCI UART driver ver 2.2
[ 4.373493] Bluetooth: HCI H4 protocol initialized
[ 4.378328] cpuidle: using governor ladder
[ 4.382413] cpuidle: using governor menu
[ 4.386665] sdhci: Secure Digital Host Controller Interface driver
[ 4.392711] sdhci: Copyright(c) Pierre Ossman
[ 4.397299] s3c-sdhci s3c-sdhci.0: clock source 0: mmc_busclk.0 (166000000 Hz)
[ 4.404494] s3c-sdhci s3c-sdhci.0: clock source 2: mmc_busclk.2 (83000000 Hz)
[ 4.413642] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[ 4.419361] VTF_2.8V: operation not allowed
[ 4.423067] s3c-sdhci s3c-sdhci.0: could not set regulator OCR (-1)
[ 4.429579] s3c-sdhci s3c-sdhci.1: clock source 0: mmc_busclk.0 (166000000 Hz)
[ 4.436774] s3c-sdhci s3c-sdhci.1: clock source 2: mmc_busclk.2 (83000000 Hz)
[ 4.445522] VTF_2.8V: operation not allowed
[ 4.448203] s3c-sdhci s3c-sdhci.0: could not set regulator OCR (-1)
[ 4.454713] mmc1: no vmmc regulator found
[ 4.460242] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[ 4.465940] s3c-sdhci s3c-sdhci.2: clock source 0: mmc_busclk.0 (166000000 Hz)
[ 4.476388] s3c-sdhci s3c-sdhci.2: clock source 2: mmc_busclk.2 (83000000 Hz)
[ 4.482175] VTF_2.8V: operation not allowed
[ 4.484543] s3c-sdhci s3c-sdhci.0: could not set regulator OCR (-1)
[ 4.491054] mmc2: no vmmc regulator found
[ 4.496685] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[ 4.502247] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.509478] usbcore: registered new interface driver usbhid
[ 4.513457] usbhid: USB HID core driver
[ 4.518528] ashmem: initialized
[ 4.520813] logger: created 256K log 'log_main'
[ 4.528884] logger: created 256K log 'log_events'
[ 4.531558] logger: created 256K log 'log_radio'
[ 4.534910] logger: created 256K log 'log_system'
[ 4.552135] IPv4 over IPv4 tunneling driver
[ 4.553324] Initializing XFRM netlink socket
[ 4.555039] NET: Registered protocol family 17
[ 4.562972] NET: Registered protocol family 15
[ 4.565666] Bluetooth: RFCOMM TTY layer initialized
[ 4.569203] Bluetooth: RFCOMM socket layer initialized
[ 4.574203] Bluetooth: RFCOMM ver 1.11
[ 4.579328] NET: Registered protocol family 33
[ 4.584577] sctp: Hash tables configured (established 16384 bind 32768)
[ 4.589796] Registering the dns_resolver key type
[ 4.597496] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[ 4.604614] registered taskstats version 1
[ 4.614795] VCC_1.8V: incomplete constraints, leaving on
[ 4.615346] VINT_1.2V: incomplete constraints, leaving on
[ 4.621985] VARM_1.2V: incomplete constraints, leaving on
[ 4.626472] CAM_AF_3.3V: incomplete constraints, leaving on
[ 4.632575] CAM_ISP_1.2V: incomplete constraints, leaving on
[ 4.637494] CAM_IO_2.8V: incomplete constraints, leaving on
[ 4.643182] VPLL_1.1V: incomplete constraints, leaving on
[ 4.649650] VCC+VCAM_2.8V: incomplete constraints, leaving on
[ 4.656416] VUSB+VADC_3.3V: incomplete constraints, leaving on
[ 4.660221] VCC_3.3V: incomplete constraints, leaving on
[ 4.665695] VTF_2.8V: incomplete constraints, leaving on
[ 4.671548] VUSB+MIPI_1.1V: incomplete constraints, leaving on
[ 4.679449] input: gpio-keys as /devices/platform/gpio-keys.0/input/input1
[ 4.687987] max8998-rtc max8998-rtc: setting system clock to 2013-02-23 08:21:42 UTC (1361607702)
[ 4.692653] ALSA device list:
[ 4.695373] No soundcards found.
[ 4.699028] Warning: unable to open an initial console.
[ 4.730337] Freeing init memory: 2636K
[ 4.730385] Write protecting the kernel text section c0008000 - c090d000
[ 4.925033] mmc2: new SD card at address aaaa
[ 4.933164] mmcblk0: mmc2:aaaa SU01G 942 MiB
[ 4.936670] mmcblk0: p1
[ 5.113958] init: cannot open '/initlogo.rle'
[ 5.348302] EXT4-fs (mtdblock1): warning: maximal mount count reached, running e2fsck is recommended
[ 5.352863] EXT4-fs (mtdblock1): recovery complete
[ 5.357121] EXT4-fs (mtdblock1): mounted filesystem with ordered data mode. Opts: (null)
[ 5.366051] EXT4-fs (mtdblock1): re-mounted. Opts: (null)
[ 5.563526] EXT4-fs (mtdblock2): warning: maximal mount count reached, running e2fsck is recommended
[ 5.567565] EXT4-fs (mtdblock2): recovery complete
[ 5.572336] EXT4-fs (mtdblock2): mounted filesystem with ordered data mode. Opts: (null)
[ 5.638145] EXT4-fs (mtdblock3): warning: maximal mount count reached, running e2fsck is recommended
[ 5.642200] EXT4-fs (mtdblock3): recovery complete
[ 5.646958] EXT4-fs (mtdblock3): mounted filesystem with ordered data mode. Opts: (null)
[ 5.659542] EXT4-fs (mtdblock4): Unrecognized mount option "check=no" or missing value
[ 5.726831] lowmem_shrink: convert oom_adj to oom_score_adj:
[ 5.726892] oom_adj 0 => oom_score_adj 0
[ 5.730922] oom_adj 1 => oom_score_adj 58
[ 5.734942] oom_adj 2 => oom_score_adj 117
[ 5.739090] oom_adj 4 => oom_score_adj 235
[ 5.743230] oom_adj 7 => oom_score_adj 411
[ 5.747323] oom_adj 15 => oom_score_adj 1000
[ 5.752406] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
sh: can't access tty; job control turned off
# [ 6.736529] init: untracked pid 139 exited
[ 7.097207] warning: `rild' uses 32-bit capabilities (legacy support in use)

How To Build
git clone git://github.com/sg3/android_kernel_samsung_s5p6442 -b s5p6442-3.4 kernel-3.4
cd kernel-3.4
make ARCH=arm apollo_defconfig
./build.sh config
./build.sh

Things to be aware of
I feel these things should be mentioned as they are important changes that may disrupt peoples user experience on the phone.
Odin will not work anymore for flashing ROMs. It's as simple as that. We will no longer be using STL/BML/TFSR for interfacing with the NAND, and that is what ODIN expects to be working with: partitions in STL format. We simply will not support STL when this kernel is complete as it is closed source and will not function on kernel 3.x. We will be moving over to MTD which is mainline, and regularly gets updates to improve performance, reliability and in general to make it better.
Kernels will however be flashable from ODIN. This WILL NOT change. Kernels, modem.bin, Sbl and boot.bin will all still work from Odin. Data, system and cache will not.
I know this will annoy a few people, as it will disrupt me too as a developer and a Windows user, it's nice to be able to flash a ROM this way, but we're going to have to move towards distributing ROMs in system.imgs, or more preferably in update.zips.
There will be no support for Samsung Froyo/Eclair ROMs in kernel 3.x. The reasoning behind this is because Samsung ROMs want Samsung drivers and we won't be using any of them. We will be aiming to support CM7 and CM9, or generally any AOSP ROM, but not Samsungs proprietary ROM. You may think 'well why not make the drivers work for both', but the problem is not with making the drivers work, the problem is with the fact that a lot of these drivers were written for a kernel over 10 major versions out of date by now, and will not function on the new kernels APIs. If we try to make them work, it will make the kernel unstable and it's going to degrade the experience for the end user. As well as that, we don't know how half these drivers actually work because they are either coded so badly it's impossible to make heads or tails of it, or it's closed source and we can't find sources for it.
There are plenty of good custom kernels for Froyo, and I have heard word in the grapevine a few people want to make a custom Eclair kernel (not confirmed, and that is just rumours), but I will not be adding support for Froyo to kernel 3.x
Kernel 3.x will not allow us to work magic with the phone. Having a newer kernel won't allow us to make the CPU itself faster, we can't give it more RAM (or find more RAM in there). We won't be able to unlock more performance from x part. This is not a magical rebirth of the phone, this is just a major fix up of all the current issues we face with AOSP based ROMs on the phone. It will most likely make the phone faster, but we can't magically make it into a dual core or something like that. It just isn't possible.

I see a reserved post there!

And one more for good luck. Now you may post.

So many reserved posts WHOA!
could possibly add a guide to clone and build it
EDIT:
Btw, also add a note about the two branches on github
android-3.0 = android-common kernel from android.googlesource.com
linux-samsung = kgene/linux-samsung on kernel.org / github

+1! Yeah guys well done! Finally! Is it only me that I think that may we have a beta or final version of Gingerbread or (cross fingers) ICS if you guys port the 3.0 kernel for our phone?

Good to have a new thread now.....
All the best Mark & all the Devs in this project..

+1 Good luck!!

Good luck with this project

All the best.. Although this is gonna take much time still waiting patiently

I may sound like an ultra-noob here : But what is Kernel 3.0 ?
Google isn't help here

You could add this to the first post but only computer programmers will understand it, unlike me

ak700 said:
I may sound like an ultra-noob here : But what is Kernel 3.0 ?
Google isn't help here
Click to expand...
Click to collapse
Newer version of the kernel that will be completely built from scratch. tom3q did this on the Spica and it worked wonders, now it's time to do it to our phone.
Smonic said:
You could add this to the first post but only computer programmers will understand it, unlike me
Click to expand...
Click to collapse
I don't like kernel.org. They're hopeless, shown by their hacking last year and their slow recovery time, and then made worse for the fact that Linus Torvalds himself switched to Github.

This is what i wanted to see since long times now. I just wanto say thank you to all the devs for just trying

Frig. I was doing so well and then I hit a brick wall with bloody assembler...
Code:
[email protected]:~/devel/galaxy3/kernel-3.0$ ./build.sh Test
Setting kernel name to (Test)
Compiling the kernel
CHK include/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
CC init/version.o
AS arch/arm/kernel/debug.o
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:157: Error: too many positional arguments
arch/arm/kernel/debug.S:173: Error: too many positional arguments
make[1]: *** [arch/arm/kernel/debug.o] Error 1
make: *** [arch/arm/kernel] Error 2
make: *** Waiting for unfinished jobs....
Anyone smarter than me with assember know what that means?
EDIT: It's to do with ASCII and UART
Line 156-170 debug.S
Code:
ENTRY(printascii)
addruart_current r3, r1, r2
b 2f
1: waituart r2, r3
senduart r1, r3
busyuart r2, r3
teq r1, #'\n'
moveq r1, #'\r'
beq 1b
2: teq r0, #0
ldrneb r1, [r0], #1
teqne r1, #0
bne 1b
mov pc, lr
ENDPROC(printascii)

hillbeast said:
Frig. I was doing so well and then I hit a brick wall with bloody assembler...
Code:
[email protected]:~/devel/galaxy3/kernel-3.0$ ./build.sh Test
Setting kernel name to (Test)
Compiling the kernel
CHK include/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
CC init/version.o
AS arch/arm/kernel/debug.o
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:157: Error: too many positional arguments
arch/arm/kernel/debug.S:173: Error: too many positional arguments
make[1]: *** [arch/arm/kernel/debug.o] Error 1
make: *** [arch/arm/kernel] Error 2
make: *** Waiting for unfinished jobs....
Anyone smarter than me with assember know what that means?
EDIT: It's to do with ASCII and UART
Line 156-170 debug.S
Code:
ENTRY(printascii)
addruart_current r3, r1, r2
b 2f
1: waituart r2, r3
senduart r1, r3
busyuart r2, r3
teq r1, #'\n'
moveq r1, #'\r'
beq 1b
2: teq r0, #0
ldrneb r1, [r0], #1
teqne r1, #0
bne 1b
mov pc, lr
ENDPROC(printascii)
Click to expand...
Click to collapse
The error is not on /arch/arm/kernel/debug.S, it's on /arch/arm/mach-s5p6442/include/mach/debug-macro.S (Error caused by just putting Samsung's .32 code into 3.x I guess...).
Check out that addruart_current is defined a few lines before, and it refers to "adduart" which is defined at debug-macro.S (that's why before defining addruart_current, debug-macro.S is included).
And if you check debug-macro.S, you'll see that adduart is defined only with one parameter, when in debug.S it's used with two parameters. That's where the error comes from.
In order to fix this, you'll have to redo the debug-macro.S file so that adduart takes two parameters (IMO should be based in S5PC110 or Spica's (or maybe s5p64x0?) debug-macro.S).

moikop said:
The error is not on /arch/arm/kernel/debug.S, it's on /arch/arm/mach-s5p6442/include/mach/debug-macro.S (Error caused by just putting Samsung's .32 code into 3.x I guess...).
Check out that addruart_current is defined a few lines before, and it refers to "adduart" which is defined at debug-macro.S (that's why before defining addruart_current, debug-macro.S is included).
And if you check debug-macro.S, you'll see that adduart is defined only with one parameter, when in debug.S it's used with two parameters. That's where the error comes from.
In order to fix this, you'll have to redo the debug-macro.S file so that adduart takes two parameters (IMO should be based in S5PC110 or Spica's (or maybe s5p64x0?) debug-macro.S).
Click to expand...
Click to collapse
Brilliant. Now we're back to good ol' fixing up references.

hillbeast said:
Frig. I was doing so well and then I hit a brick wall with bloody assembler...
Code:
[email protected]:~/devel/galaxy3/kernel-3.0$ ./build.sh Test
Setting kernel name to (Test)
Compiling the kernel
CHK include/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
CC init/version.o
AS arch/arm/kernel/debug.o
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:157: Error: too many positional arguments
arch/arm/kernel/debug.S:173: Error: too many positional arguments
make[1]: *** [arch/arm/kernel/debug.o] Error 1
make: *** [arch/arm/kernel] Error 2
make: *** Waiting for unfinished jobs....
Click to expand...
Click to collapse
you're using homebrew right? if yes, does it compile faster? in a word, ill grab my sis macbook pro !
BTW, which baseband are you gonna use for this kernel ?

[Q] Useless Arndale board exynos5250

Code:
Checking Boot Mode ... SDMMC
REVISION: 1.0
REVISION: 1.0
MMC Device 0: 7691 MB
[ERROR] response timeout error : 00000104 cmd 1
[ERROR] response timeout error : 00000104 cmd 1
MMC Device 1: 0 MB
MMC Device 2 not found
*** Warning - using default environment
Hit any key to stop autoboot: 0
reading kernel..device 0 Start 1063, Count 10240
MMC read: dev # 0, block # 1063, count 10240 ... 10240 blocks read: OK
completed
reading RFS..device 0 Count 11303, Start 2048
MMC read: dev # 0, block # 11303, count 2048 ... 2048 blocks read: OK
completed
Boot with zImage
## Loading init Ramdisk from Legacy Image at 41000000 ...
Image Name: Android Ramdisk Image
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 167666 Bytes = 167666 Load Address: 40800000
Entry Point: 40800000
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.31-g3370a7c ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Feb 21 21:47:51 MST 2014
CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: ARNDALE
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writealloc
S3C24XX Clocks, Copyright 2004 Simtec Electronics
s3c_register_clksrc: clock audiocdclk has no registers set
audiocdclk: no parent clock specified
EXYNOS5: PLL settings, A=1400000000, B=1333090909, C=333000000
M=1600000000, E=96000000, V=300000000, G=533000000
EXYNOS5: ARMCLK=1400000000, CDREX=800000000, ACLK400=533000000
ACLK333=333000000, ACLK266=266666666, ACLK200=200000000
ACLK166=166500000, ACLK66=66666666
uclk1: source is mout_mpll_user (6), rate is 200000000
uclk1: source is mout_mpll_user (6), rate is 200000000
uclk1: source is ext_xtal (0), rate is 6000000
uclk1: source is mout_mpll_user (6), rate is 200000000
sclk_usbdrd30: source is mout_mpll (0), rate is 66666666
sclk_fimd: source is ext_xtal (0), rate is 24000000
aclk_266_gscl: source is aclk_266 (1), rate is 266666666
sclk_g3d: source is mout_mpll_user (0), rate is 800000000
sclk_sata: source is mout_mpll_user (0), rate is 66666666
sclk_gscl_wrap0: source is ext_xtal (0), rate is 24000000
sclk_gscl_wrap1: source is ext_xtal (0), rate is 24000000
sclk_cam0: source is ext_xtal (0), rate is 24000000
sclk_cam1: source is ext_xtal (0), rate is 24000000
PERCPU: Embedded 7 pages/cpu @c2036000 s7744 r8192 d12736 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519938
Kernel command line: console=ttySAC2,115200n8 vmalloc=512M androidboot.console=ttySAC2
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 2047MB = 2047MB total
Memory: 1839508k/1839508k available, 256620k reserved, 1735680K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xfea00000 - 0xffe00000 ( 20 MB)
vmalloc : 0xd6800000 - 0xf6000000 ( 504 MB)
lowmem : 0xc0000000 - 0xd6000000 ( 352 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.init : 0xc0008000 - 0xc0043000 ( 236 kB)
.text : 0xc0043000 - 0xc0724000 (7044 kB)
.data : 0xc0724000 - 0xc07876a0 ( 398 kB)
.bss : 0xc07876c4 - 0xc08e7978 (1409 kB)
SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:552
Console: colour dummy device 80x30
Calibrating delay loop... 2795.11 BogoMIPS (lpj=6987776)
[ 0.045000] pid_max: default: 32768 minimum: 301
[ 0.045000] Mount-cache hash table entries: 512
[ 0.045000] Initializing cgroup subsys debug
[ 0.045000] Initializing cgroup subsys cpuacct
[ 0.045000] Initializing cgroup subsys freezer
[ 0.045000] CPU: Testing write buffer coherency: ok
[ 0.045000] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[ 0.085000] CPU1: Booted secondary processor
[ 0.095000] Brought up 2 CPUs
[ 0.095000] SMP: Total of 2 processors activated (5590.22 BogoMIPS).
[ 0.100000] gpio: GPZ has no PM function
[ 0.100000] print_constraints: dummy:
[ 0.100000] NET: Registered protocol family 16
[ 0.105000] SMDK MAIN Board Rev 0.2 (ADC value:783)
[ 0.110000] ath6kl_set_platform_data ~~~~~~~~~~~~~~~~
[ 0.110000] hw-breakpoint: debug architecture 0x5 unsupported.
[ 0.110000] exynos5_pmu_init: PMU supports 52XX(98)
[ 0.110000] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.115000] EXYNOS5: Initializing architecture
[ 0.115000] s3c-adc samsung-adc-v4: attached adc driver
[ 0.115000] samsung-pd samsung-pd.0: power domain registered
[ 0.115000] samsung-pd samsung-pd.1: power domain registered
[ 0.115000] samsung-pd samsung-pd.8: power domain registered
[ 0.115000] samsung-pd samsung-pd.9: power domain registered
[ 0.115000] samsung-pd samsung-pd.10: power domain registered
[ 0.115000] samsung-pd samsung-pd.11: power domain registered
[ 0.115000] s3c24xx-pwm s3c24xx-pwm.0: tin at 66666666, tdiv at 66666666, tin=divclk, base 0
[ 0.115000] EXYNOS ASV PMIC MAXIM Detected!
[ 0.115000] VDD_ARM[SG FUSED] ASV group is 6
[ 0.115000] VDD_INT[SG FUSED] ASV group is 6
[ 0.115000] VDD_MIF[SG FUSED] ASV group is 2
[ 0.115000] VDD_G3D[SG FUSED] ASV group is 6
[ 0.135000] bio: create slab <bio-0> at 0
[ 0.135000] print_constraints: VDD_1.8V: 1800 mV
[ 0.135000] print_constraints: DC_5V: 5000 mV
[ 0.135000] print_constraints: VDD_3.3V: 3300 mV
[ 0.135000] print_constraints: DC_5V: 5000 mV
[ 0.135000] rdev_init_debugfs: DC_5V: Failed to create debugfs directory
[ 0.135000] print_constraints: CAM_SENSOR_0: 1800 mV
[ 0.135000] SCSI subsystem initialized
[ 0.140000] usbcore: registered new interface driver usbfs
[ 0.140000] usbcore: registered new interface driver hub
[ 0.140000] usbcore: registered new device driver usb
[ 0.140000] s5m87xx 0-0066: S5M MFD Detected. DEVICE ID = 5
[ 0.140000] print_constraints: vdd_ldo4: 1800 mV
[ 0.145000] print_constraints: vdd_mif range: 950 <--> 1300 mV at 1100 mV
[ 0.145000] print_constraints: vdd_arm range: 800 <--> 1350 mV at 1200 mV
[ 0.145000] print_constraints: vdd_int range: 900 <--> 1200 mV at 1200 mV
[ 0.145000] print_constraints: vdd_g3d range: 700 <--> 1300 mV at 1200 mV
[ 0.145000] print_constraints: vdd_ldo11 range: 1900 mV
[ 0.145000] print_constraints: vdd_ldo14 range: 1900 mV
[ 0.145000] s5m87xx 0-0066: S5M87xx MFD probe done!!!
[ 0.145000] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.145000] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[ 0.150000] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.150000] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[ 0.150000] s3c-i2c s3c2440-i2c.4: i2c-4: S3C I2C adapter
[ 0.150000] s3c-i2c s3c2440-i2c.5: i2c-5: S3C I2C adapter
[ 0.150000] s3c-i2c s3c2440-hdmiphy-i2c: i2c-8: S3C I2C adapter
[ 0.150000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.150000] Bluetooth: Core ver 2.16
[ 0.150000] NET: Registered protocol family 31
[ 0.150000] Bluetooth: HCI device and connection manager initialized
[ 0.150000] Bluetooth: HCI socket layer initialized
[ 0.150000] Bluetooth: L2CAP socket layer initialized
[ 0.150000] Bluetooth: SCO socket layer initialized
[ 0.150000] Switching to clocksource mct-frc
[ 0.151036] Switched to NOHz mode on CPU #0
[ 0.154969] Switched to NOHz mode on CPU #1
[ 0.155058] cfg80211: Calling CRDA to update world regulatory domain
[ 0.168386] NET: Registered protocol family 2
[ 0.168544] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.169053] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.169759] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.170546] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.170554] TCP reno registered
[ 0.170564] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.170580] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.170784] NET: Registered protocol family 1
[ 0.170914] Trying to unpack rootfs image as initramfs...
[ 0.176996] Freeing initrd memory: 160K
[ 0.177086] PMU: registered new PMU device of type 0
[ 0.177237] Exynos5 : ARM Clock down on idle mode is enabled
[ 0.177554] Loaded driver for PL330 DMAC-0 s3c-pl330
[ 0.177563] DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[ 0.177644] Loaded driver for PL330 DMAC-1 s3c-pl330
[ 0.177651] DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.177727] Loaded driver for PL330 DMAC-2 s3c-pl330
[ 0.177734] DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.183261] highmem bounce pool size: 64 pages
[ 0.183466] ashmem: initialized
[ 0.191472] fuse init (API version 7.16)
[ 0.191787] msgmni has been set to 203
[ 0.192563] io scheduler noop registered
[ 0.192571] io scheduler deadline registered
[ 0.192607] io scheduler cfq registered (default)
[ 0.405053] s5p-mipi-dsim s5p-mipi-dsim: DSI Master driver has been completed.
[ 0.405064] s5p-mipi-dsim s5p-mipi-dsim: DSI Master state is stop state
[ 0.677067] s5p-mipi-dsim s5p-mipi-dsim: mipi-dsi driver(RGB mode) has been probed.
[ 0.677416] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.735283] s5pv210-uart.0: ttySAC0 at MMIO 0x12c00000 (irq = 16) is a S3C6400/10
[ 0.750067] s5pv210-uart.1: ttySAC1 at MMIO 0x12c10000 (irq = 20) is a S3C6400/10
[ 0.765066] s5pv210-uart.2: ttySAC2 at MMIO 0x12c20000 (irq = 24) is a S3C6400/10
[ 1.662745] console [ttySAC2] enabled
[ 1.680066] s5pv210-uart.3: ttySAC3 at MMIO 0x12c30000 (irq = 28) is a S3C6400/10
[ 1.701966] mali mali-t604.0: Probed as mali0
[ 1.705550] UMP: UMP device driver r1p0-04rel0 loaded
[ 1.715955] brd: module loaded
[ 1.720571] loop: module loaded
[ 1.722300] ============ gps power probe !!!!! ===============
[ 1.728459] ============ gps power reset !!!!! ===============
[ 1.735146] print_constraints: AVDD1: at 3000 mV
[ 1.739564] print_constraints: DCVDD: at 1000 mV
[ 1.744579] wm8994 3-001a: WM8994 revision C
[ 1.755066] wm8994 3-001a: No interrupt specified, no interrupts
[ 1.759988] i2c-core: driver [wm8994] using legacy suspend method
[ 1.765666] i2c-core: driver [wm8994] using legacy resume method
[ 3.035047] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 392157Hz, actual 390625HZ div = 64)
[ 3.085099] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 3.133326] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 3.141667] wm8994-codec wm8994-codec: Failed to request Mic1 short IRQ: -22
[ 3.148673] mmc1: new high speed SDHC card at address b368
[ 3.154087] wm8994-codec wm8994-codec: Failed to request Mic2 detect IRQ: -22
[ 3.161247] usb 1-3.2.4: new high speed USB device number 4 using s5p-ehci
[ 3.168184] wm8994-codec wm8994-codec: Failed to request Mic2 short IRQ: -22
[ 3.175242] mmcblk0: mmc1:b368 MS 7.51 GiB
[ 3.180693] mmcblk0: p1 p2 p3 p4
[ 3.210042] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 3.228610] asoc: wm8994-aif1 <-> samsung-i2s.0 mapping ok
[ 3.233332] ALSA device list:
[ 3.235603] #0: Arndale
[ 3.238224] GACT probability NOT on
[ 3.241672] Mirror/redirect action on
[ 3.245349] u32 classifier
[ 3.248028] Actions configured
[ 3.251375] Netfilter messages via NETLINK v0.30.
[ 3.256080] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 3.262784] ctnetlink v0.93: registering with nfnetlink.
[ 3.267414] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.274338] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.280192] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 392157Hz, actual 390625HZ div = 64)
[ 3.289939] xt_time: kernel timezone is -0000
[ 3.295867] IPv4 over IPv4 tunneling driver
[ 3.299490] GRE over IPv4 demultiplexor driver
[ 3.303431] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.308464] arp_tables: (C) 2002 David S. Miller
[ 3.312922] TCP cubic registered
[ 3.316714] NET: Registered protocol family 10
[ 3.323136] Mobile IPv6
[ 3.324117] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.329657] IPv6 over IPv4 tunneling driver
[ 3.335051] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 3.344917] NET: Registered protocol family 17
[ 3.347923] NET: Registered protocol family 15
[ 3.352395] Bluetooth: RFCOMM socket layer initialized
[ 3.357420] Bluetooth: RFCOMM ver 1.11
[ 3.361179] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.366436] Bluetooth: BNEP filters: protocol multicast
[ 3.371651] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.377705] NET: Registered protocol family 35
[ 3.382475] rfkill_gpio rfkill_gpio: arndale-bt device registered.
[ 3.388263] EXYNOS5250: Adaptive Support Voltage init
[ 3.390070] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 392157Hz, actual 390625HZ div = 64)
[ 3.402598] EXYNOS5250(SG): ORIG : 6 MOD : 0 RESULT : 6
[ 3.407866] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 3.415519] Registering SWP/SWPB emulation handler
[ 3.420272] DVFS : VDD_ARM Voltage table set with 6 Group
[ 3.425628] VDD_ARM : L0, 0 uV
[ 3.428275] VDD_G3D : Voltage table set with 6 Group, exynos_lot_id : 0
[ 3.435246] VDD_ARM : L1, 0 uV
[ 3.438262] VDD_ARM : L2, 0 uV
[ 3.441313] VDD_ARM : L3, 0 uV
[ 3.444329] VDD_ARM : L4, 0 uV
[ 3.447378] VDD_ARM : L5, 1212500 uV
[ 3.450932] VDD_ARM : L6, 1175000 uV
[ 3.454468] VDD_ARM : L7, 1125000 uV
[ 3.458039] VDD_ARM : L8, 1087500 uV
[ 3.461596] VDD_ARM : L9, 1062500 uV
[ 3.465145] VDD_ARM : L10, 1024999 uV
[ 3.468769] VDD_ARM : L11, 1000000 uV
[ 3.472424] VDD_ARM : L12, 975000 uV
[ 3.475978] VDD_ARM : L13, 950000 uV
[ 3.479516] VDD_ARM : L14, 937500 uV
[ 3.483183] VDD_ARM : L15, 912500 uV
[ 3.486638] VDD_ARM : L16, 900000 uV
[ 3.490191] VDD_ARM : L17, 900000 uV
[ 3.493728] VDD_ARM : L18, 900000 uV
[ 3.497301] VDD_ARM : L19, 900000 uV
[ 3.500853] VDD_ARM : L20, 900000 uV
[ 3.504737] [ 6 ] Memory is not LPDDR type.
[ 3.508627] DVFS : VDD_INT Voltage table set with 6 Group
[ 3.513942] DVFS : VDD_INT Voltage of L0 level is 975000
[ 3.519323] DVFS : VDD_MIF Voltage table set with 0 Group
[ 3.524685] DVFS : VDD_MIF Voltage of L0 level is 1037500
[ 3.531095] Failed to init busfreq.
[ 3.533758] exynos_integrated_dvfs_hotplug_init, max(1700000),min(200000)
[ 3.540515] ** temperature set value **
[ 3.540518] Throttling stop_temp = 82 start_temp = 85
[ 3.540523] Waring stop_temp = 95 start_tmep = 103
[ 3.540526] Tripping temp = 110
[ 3.540529] Hw_tripping temp = 113
[ 3.540532] Trhottling freq = 800000 Warning freq = 200000
[ 3.568542] TC_voltage stop_temp = 13 Start_temp = 10
[ 3.573656] exynos5250_find_busfreq_by_volt: req_volt has no value.
[ 3.579891] get_busfreq_value error
[ 3.583358] exynos_tmu_init: cpufreq_level[14], busfreq_value[0]
[ 3.590362] Tmu Initialization is sucessful...!
[ 3.596374] s3c-fb exynos5-fb.1: window 2: fb
[ 3.600574] s3c-fb exynos5-fb.1: window 1: fb
[ 3.604953] s3c-fb exynos5-fb.1: window 0: fb
[ 3.612644] otg_wakelock_init: No OTG transceiver found
[ 3.616432] s3c-rtc exynos-rtc: setting system clock to 2000-01-01 00:00:02 UTC (946684802)
[ 3.624923] Freeing init memory: 236K
[ 3.636324] init: could not import file 'init.mt6620.rc' from '/init.arndale.rc'
[ 3.642471] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[ 3.782918] init: cannot open '/initlogo.rle'
[ 3.905808] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.930212] ASIX USB Ethernet Adapter:v4.4.0 21:45:46 Feb 21 2014
[ 3.930246] <6> http://www.asix.com.tw
[ 3.939341] eth%d: status ep1in, 8 bytes period 11
[ 3.961136] EXT4-fs (mmcblk0p4): warning: checktime reached, running e2fsck is recommended
[ 3.971457] eth0: register 'asix' at usb-s5p-ehci-3.2.4, ASIX AX88772A USB 2.0 Ethernet, 00:00:00:00:00:00
[ 3.980628] EXT4-fs (mmcblk0p4): recovery complete
[ 3.987703] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 5.610836] EXT4-fs (mmcblk0p3): warning: checktime reached, running e2fsck is recommended
[ 6.010442] EXT4-fs (mmcblk0p3): recovery complete
[ 6.114691] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,noauto_da_alloc,errors=panic
[ 6.186538] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[ 6.237436] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 6.266535] adb_open
[ 6.267283] mtp_bind_config
[ 6.270272] adb_bind_config
[ 6.275425] android_work: did not send uevent (0 0 (null))
[email protected]:/ $ [ 7.293438] LOW resolution is reported
[ 7.491024] ion_share_mmap: trying to map larger area than handle has available
[ 7.498863] ion_share_mmap: trying to map larger area than handle has available
[ 13.729169] warning: `zygote' uses 32-bit capabilities (legacy support in use)
[ 14.505784] request_suspend_state: wakeup (3->0) at 14505776635 (2000-01-01 00:00:13.384388132 UTC)
[ 14.514760] init: untracked pid 1426 exited
[ 14.518119] init: untracked pid 1431 exited
[ 16.843227] request_suspend_state: wakeup (0->0) at 16843219718 (2000-01-01 00:00:15.721830799 UTC)
[ 16.851963] init: untracked pid 1806 exited
[ 16.856005] init: untracked pid 1805 exited
[ 22.096914] request_suspend_state: wakeup (0->0) at 22096905679 (2000-01-01 00:00:20.975517177 UTC)
[ 22.107107] init: untracked pid 2003 exited
[ 22.109837] init: untracked pid 2004 exited
[ 1.771653] Uniform Multi-Platform E-IDE driver
[ 1.776367] ide-gd driver 1.18
[ 1.779439] rdac: device handler registered
[ 1.783403] hp_sw: device handler registered
[ 1.787594] emc: device handler registered
[ 1.791672] alua: device handler registered
[ 1.798285] ahci ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 1.804559] ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 1.812112] VDD_G3D : Voltage table set with 0 Group, exynos_lot_id : 0
[ 1.819530] scsi0 : ahci_platform
[ 1.822325] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122fffff] port 0x100 irq 179
[ 1.830444] usbcore: registered new interface driver asix
[ 1.835421] usbcore: registered new interface driver cdc_ether
[ 1.841244] usbcore: registered new interface driver net1080
[ 1.846859] usbcore: registered new interface driver cdc_subset
[ 1.852751] usbcore: registered new interface driver zaurus
[ 1.858210] cdc_ncm: 04-Aug-2011
[ 1.861517] usbcore: registered new interface driver cdc_ncm
[ 1.867040] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.873738] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 1.878753] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 1.885804] s5p-ehci s5p-ehci: irq 135, io mem 0x12110000
[ 1.900055] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 1.904418] hub 1-0:1.0: USB hub found
[ 1.907722] hub 1-0:1.0: 3 ports detected
[ 1.912129] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.917910] s5p-ohci s5p-ohci: Already power on PHY
[ 1.922707] s5p-ohci s5p-ohci: s5p OHCI
[ 1.926529] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
[ 1.933551] s5p-ohci s5p-ohci: irq 135, io mem 0x12120000
[ 1.994539] hub 2-0:1.0: USB hub found
[ 1.996836] hub 2-0:1.0: 3 ports detected
[ 2.001359] exynos-xhci exynos-xhci: EXYNOS xHCI Host Controller
[ 2.006805] exynos-xhci exynos-xhci: new USB bus registered, assigned bus number 3
[ 2.014545] exynos-xhci exynos-xhci: irq 136, io mem 0x12000000
[ 2.020648] hub 3-0:1.0: USB hub found
[ 2.023941] hub 3-0:1.0: 1 port detected
[ 2.028109] exynos-xhci exynos-xhci: EXYNOS xHCI Host Controller
[ 2.033840] exynos-xhci exynos-xhci: new USB bus registered, assigned bus number 4
[ 2.041828] hub 4-0:1.0: USB hub found
[ 2.045105] hub 4-0:1.0: 1 port detected
[ 2.049467] usbcore: registered new interface driver cdc_acm
[ 2.054641] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.062612] Initializing USB Mass Storage driver...
[ 2.067596] usbcore: registered new interface driver usb-storage
[ 2.073446] USB Mass Storage support registered.
[ 2.078242] usbcore: registered new interface driver usbserial
[ 2.083848] usbserial: USB Serial Driver core
[ 2.088257] USB Serial support registered for pl2303
[ 2.093253] usbcore: registered new interface driver pl2303
[ 2.098655] pl2303: Prolific PL2303 USB to serial adaptor driver
[ 2.104882] s3c-udc : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Electronics
[ 2.104887] s3c-udc : version 15 March 2009
[ 2.118676] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 2.124077] android_usb gadget: Number of LUNs=1
[ 2.128700] lun0: LUN: removable file: (no medium)
[ 2.133901] android_usb gadget: android_usb ready
[ 2.138214] Registered gadget driver 'android_usb'
[ 2.142973] s3c-usbgadget s3c-usbgadget: Already power on PHY
[ 2.148722] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.155169] android_work: did not send uevent (0 0 (null))
[ 2.159788] android_work: did not send uevent (0 0 (null))
[ 2.165478] mousedev: PS/2 mouse device common for all mice
[ 2.171679] input: gpio-keys as /devices/platform/gpio-keys.0/input/input0
[ 2.178534] input: unidisplay_ts as /devices/platform/s3c2440-i2c.7/i2c-7/7-0041/input/input1
[ 2.186571] Unidisplay touch driver registered successfully
[ 2.192568] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 2.197219] s3c-rtc exynos-rtc: rtc disabled, re-enabling
[ 2.202511] s3c-rtc exynos-rtc: rtc clk out disabled, re-enabling
[ 2.208607] s3c-rtc exynos-rtc: warning: invalid RTC value so initializing it
[ 2.216038] using rtc device, s3c, for alarms
[ 2.219868] s3c-rtc exynos-rtc: rtc core: registered s3c as rtc0
[ 2.226016] usb 1-3: new high speed USB device number 2 using s5p-ehci
[ 2.232633] i2c /dev entries driver
[ 2.237173] Linux media interface: v0.10
[ 2.239962] Linux video capture interface: v2.00
[ 2.244540] many: s5k4ecgx_mod_init
[ 2.248067] S5P MFC V4L2 Driver, (c) 2010 Samsung Electronics
[ 2.253925] s5p-mfc s5p-mfc-v6: decoder registered as /dev/video6
[ 2.259866] s5p-mfc s5p-mfc-v6: encoder registered as /dev/video7
[ 2.266269] exynos-mdev.0: Media0[0xcbb9f800] was registered successfully
[ 2.272709] exynos-mdev.1: Media1[0xcbb9e000] was registered successfully
[ 2.279452] exynos-mdev.2: Media2[0xcbb9c800] was registered successfully
[ 2.286290] s5p-mipi-csis.0
[ 2.286294] : s5pcsis_probe : csis0 probe success
[ 2.293716] s5p-mipi-csis.1
[ 2.293719] : s5pcsis_probe : csis1 probe success
[ 2.301588] S5K4ECGX 4-0056: s5k4ecgx_init_formats:
[ 2.305904] S5K4ECGX 4-0056: s5k4ecgx_init_parameters:
[ 2.311100] S5K4ECGX 4-0056: s5k4ecgx_stop_auto_focus: single AF Off command Setting
[ 2.365942] hub 1-3:1.0: USB hub found
[ 2.368283] hub 1-3:1.0: 3 ports detected
[ 2.465059] exynos-mdev.1: Registered sensor subdevice S5K4ECGX
[ 2.469520] [INFO]flite_probe:2485: FIMC-LITE0 probe success
[ 2.475456] [INFO]flite_probe:2485: FIMC-LITE1 probe success
[ 2.481042] [INFO]flite_probe:2485: FIMC-LITE2 probe success
[ 2.488508] hdmiphy init start
[ 2.490246] i2c i2c-2: attached exynos hdcp into i2c adapter successfully
[ 2.496958] i2c-core: driver [exynos_hdcp] using legacy suspend method
[ 2.503354] i2c-core: driver [exynos_hdcp] using legacy resume method
[ 2.509773] Samsung HDMI output driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[ 2.517577] s5p-hdmi exynos5-hdmi: hdmiphy i2c bus number = 8
[ 2.523407] hdmiphy_probe start
[ 2.526238] s5p-hdmiphy 8-0038: probe successful
[ 2.640185] s5p_hpd_kobject_uevent: sent uevent HDMI_STATE=offline
[ 2.644976] s5p-hdmi exynos5-hdmi: probe sucessful
[ 2.649804] Samsung TV Mixer driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[ 2.657294] s5p-mixer s5p-mixer: probe start
[ 2.661375] s5p-mixer s5p-mixer: resources acquired
[ 2.666162] s5p-mixer s5p-mixer: added output 'S5P HDMI connector' from module 's5p-hdmi'
[ 2.674302] usb 1-3.2: new high speed USB device number 3 using s5p-ehci
[ 2.681155] s5p-mixer s5p-mixer: registered layer mxr0_graph0 as /dev/video16
[ 2.688259] s5p-mixer s5p-mixer: registered layer mxr0_graph1 as /dev/video17
[ 2.695329] s5p-mixer s5p-mixer: registered layer mxr1_graph2 as /dev/video18
[ 2.702438] s5p-mixer s5p-mixer: registered layer mxr1_graph3 as /dev/video19
[ 2.709375] s5p-mixer s5p-mixer: mixer0 create links
[ 2.714319] s5p-mixer s5p-mixer: mixer1 create links
[ 2.719273] s5p-mixer s5p-mixer: mixer links are created successfully
[ 2.725714] s5p-mixer s5p-mixer: probe successful
[ 2.730452] S5P CEC for Exynos4 Driver, (c) 2009 Samsung Electronics
[ 2.736923] s5p-tvout-cec s5p-tvout-cec: probe successful
[ 2.742213] exynos-rot exynos-rot: ++rot_probe
[ 2.746655] exynos-rot exynos-rot: rotator registered successfully
[ 2.752743] Initialize JPEG driver
[ 2.756217] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video12
[ 2.762823] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video11
[ 2.769756] Samsung Graphics 2D driver, (c) 2011 Samsung Electronics
[ 2.775814] samsung-fake-battery samsung-fake-battery: samsung_fake_bat_probe
[ 2.783793] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 2.788889] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[ 2.796914] device-mapper: uevent: version 1.0.3
[ 2.801289] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected]
[ 2.809353] Bluetooth: HCI UART driver ver 2.2
[ 2.813756] Bluetooth: HCI H4 protocol initialized
[ 2.818516] Bluetooth: HCI BCSP protocol initialized
[ 2.823603] Bluetooth: HCILL protocol initialized
[ 2.828155] Bluetooth: HCIATH3K protocol initialized
[ 2.833298] hub 1-3.2:1.0: USB hub found
[ 2.837295] hub 1-3.2:1.0: 4 ports detected
[ 2.841175] cpuidle: using governor ladder
[ 2.845821] cpuidle: using governor menu
[ 2.849271] dw_mmc dw_mmc.0: Using internal DMA controller.
[ 2.854679] mmc0: no vmmc regulator found
[ 2.858882] dw_mmc dw_mmc.0: Version ID is 241a
[ 2.863130] dw_mmc dw_mmc.0: DW MMC controller at irq 139, 32 bit host data width, 128 deep fifo
[ 2.871956] dw_mmc dw_mmc.2: Using internal DMA controller.
[ 2.877444] mmc1: no vmmc regulator found
[ 2.881607] dw_mmc dw_mmc.2: Version ID is 241a
[ 2.885935] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 2.890048] dw_mmc dw_mmc.2: DW MMC controller at irq 141, 32 bit host data width, 128 deep fifo
[ 2.890139] dw_mmc dw_mmc.1: Using internal DMA controller.
[ 2.890175] mmc2: no vmmc regulator found
[ 2.890674] dw_mmc dw_mmc.1: Version ID is 241a
[ 2.890699] dw_mmc dw_mmc.1: DW MMC controller at irq 140, 32 bit host data width, 128 deep fifo
[ 2.891141] sdhci: Secure Digital Host Controller Interface driver
[ 2.891148] sdhci: Copyright(c) Pierre Ossman
[ 2.891598] mshci: Mobile Storage Host Controller Interface driver
[ 2.891606] mshci: Copyright (c) 2011 Samsung Electronics Co., Ltd
[ 2.891617] Error: Driver 'dw_mmc' is already registered, aborting...
[ 2.892259] S5P ACE Driver, (c) 2010 Samsung Electronics
[ 2.961557] ACE: ecb-aes-s5p-ace
[ 2.964695] ACE: cbc-aes-s5p-ace
[ 2.967946] ACE: ctr-aes-s5p-ace
[ 2.971175] ACE: sha1-s5p-ace
[ 2.974071] ACE: sha256-s5p-ace
[ 2.977145] ACE driver is initialized
[ 2.981281] usbcore: registered new interface driver usbhid
[ 2.986280] usbhid: USB HID core driver
[ 2.990492] logger: created 256K log 'log_main'
[ 2.994724] logger: created 256K log 'log_events'
[ 2.999428] logger: created 256K log 'log_radio'
[ 3.004034] logger: created 256K log 'log_system'
[ 3.010131] Samsung Audio Subsystem Driver, (c) 2011 Samsung Electronics

exynos5250
I am having problems getting my Arndale board to launch. I have installed 3 different versions of ubuntu to try and make the proper build environment. either the board stalls while launching, or i get a boot loop with a re-occurring code that i am not sure what it is. My log is posted above with the re-occurring code. If anyone can tell me what i am doing wrong i would really appreciate it. I had to ask one of the moderators to put my log in for me. As a new member i am not allowed to post links yet and it seems to think there are links in my log. The way in which i had to get the log to him was through pm and in 3 parts, so the log is a little jumbled up. I will straighten it out as soon as i can.
I have already went about retrying my build environment so i will not be able to exactly reproduce this error but i have come to a similar wall roughly 3 times now. If details are needed as to how i am setting up my build environment i can certainly provide them.
Also if I am not mistaken the Arndale exynos5250 shares alot of it's hardware with the nexus 10 including the ASOP? so if this is a possible route to go i would love to know. Basically all i am looking to do is set up my board with the crypto twofish patch, and three modules for CDC-ACM, PL2303, and one for the EasyCAP.
I am having a problem figuring out how to set my mac address for the built in Ethernet as well, potentially a patch for a Ethernet radio button as well.
Thank you.

A little more detail
So I had originally purchased this board around a year and a half ago. I had problems getting the paid apps to work and the gps module was faulty. It took me around a month to properly get a u-boot built to flash the board and by that time my return on the gps module had lapsed. I continued to try and properly set up a build environment to compile the kernel and system, but with little success. I had lost all hope of this board ever becoming anything useful, and had successfully wasted around 500$.
Fast forward a year and a half and i stumble across an article detailing how to implement a usb GPS. The GPS unit was only around 20$ shipped so i figured why not give it a try. It was successful, a little slow on the refresh rate but successful never the less. This is around the time i was determined to make my 500$ paperweight into something of value. I had decided to start looking into making it a car-droid-pc. I had also came across a post on the arndale forum stating that the paid apps could be fixed via a crypto twofish patch (I have still yet to see whether or not i am applying it correctly)
Some of the elements i wish to apply to my project consist of a thermally controlled relay, resistive control to keyboard module (steering wheel control), OBD2 to usb (pl2303 chip), reverse camera via EasyCAP tuner, some way to implement bluetooth calling, and perhaps A2DP or wireless network for music streaming (A2DP could go hand in hand with bluetooth calling)
If anyone is interested in more details of the project i am happy to go into further detail.

on a side note
I was trying to read through my log to see if any of it made sense to me and i cam across something interesting.
Linux version 3.0.31-g3370a7c ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Feb 21 21:47:51 MST 2014
however when i run arm-none-linux-gnueabi-gcc -print-search-dirs | grep libraries | sed 's/:/\n/g' i get back
libraries
=/usr/local/arm-2009q3/bin/../lib/gcc/arm-none-linux-gnueabi/4.4.1/
/usr/local/arm-2009q3/bin/../lib/gcc/
/usr/local/arm-2009q3/bin/../lib/gcc/arm-none-linux-gnueabi/4.4.1/../../../../arm-none-linux-gnueabi/lib/arm-none-linux-gnueabi/4.4.1/
/usr/local/arm-2009q3/bin/../lib/gcc/arm-none-linux-gnueabi/4.4.1/../../../../arm-none-linux-gnueabi/lib/
/usr/local/arm-2009q3/bin/../arm-none-linux-gnueabi/libc/lib/arm-none-linux-gnueabi/4.4.1/
/usr/local/arm-2009q3/bin/../arm-none-linux-gnueabi/libc/lib/
/usr/local/arm-2009q3/bin/../arm-none-linux-gnueabi/libc/usr/lib/arm-none-linux-gnueabi/4.4.1/
/usr/local/arm-2009q3/bin/../arm-none-linux-gnueabi/libc/usr/lib/
all listed as 4.4.1 which is what the wiki instructs to do, so why is it that i am getting a gcc version of 4.6.x ??? rather than 4.4.1

somthing intresting help unbrick

[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=0 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=1 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=2 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=3 rdata=5AA5
[PMIC_WRAP]wrap_init pass,the return value=0.
pl pmic init start
pl pmic efuse start
pl pmic efuse BUCK trim
[0x1C8]=0xF802
[0x1CA]=0x807F
[0x20E]=0xE0
[0x260]=0xF0
[0x286]=0xF0
pl pmic efuse end
pl pmic en rst [0x126]=0x13
[0xE]=0x1
[0x540]=0xA0
Battery exist
[0xE]=0x1
[0x540]=0xA0
pl vm read [0x290]=0x50
pl vm set [0x290]=0x52
pl vm check [0x290]=0x52
pl pmic init done
[PLFM] Init I2C: OK(0)
[PLFM] Init PWRAP: OK(0)
[PLFM] Init PMIC: OK(0)
[PLFM] chip[CA00]
[I2C][PL] [i2c0 write] i2c transaction complate
[BLDR] Build Time: 20140218-141828
==== Dump RGU Reg ========
RGU MODE: 75
RGU LENGTH: FFE0
RGU STA: 40000000
RGU INTERVAL: FFF
RGU SWSYSRST: 0
==== Dump RGU Reg End ====
RGU: g_rgu_satus:2
mtk_wdt_mode_config mode value=35, tmp:22000030
PL RGU RST: ??
SW reset with bypass power key flag
Find bypass powerkey flag
mtk_wdt_mode_config mode value=70, tmp:22000071
kpd register for pmic set!
mt_usb_calibraion: input_reg = 0x0
mt_usb_calibraion: term_vref = 0x0, clkref = 0x0, vrt_vref = 0x0,
[RTC] bbpu = 0x5, con = 0x426
[RTC] irqsta = 0x0, pdn1 = 0x0, pdn2 = 0x201, spar0 = 0x40, spar1 = 0x800
[RTC] new_spare0 = 0x0, new_spare1 = 0x1, new_spare2 = 0x1, new_spare3 = 0x1
[RTC] bbpu = 0x5, con = 0x424
SW reset with bypass power key flag
SW reset with bypass power key flag
[PLFM] WDT reboot bypass power key!
p1 pmic read INT_RSV(bit7)[0x138][0x80]
[RTC] rtc_bbpu_power_on done
[SD0] Bus Width: 1
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(0) DDR(0) DIV(193) DS(0) RS(0)
[SD0] Switch to High-Speed mode!
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(2) DDR(1) DIV(96) DS(0) RS(0)
[SD0] Bus Width: 8
[SD0] Size: 3696 MB, Max.Speed: 52000 kHz, blklen(512), nblks(7569408), ro(0)
[SD0] Initialized
[SD0] SET_CLK(52000kHz): SCLK(50000kHz) MODE(2) DDR(1) DIV(0) DS(0) RS(0)
msdc_ett_offline_to_pl: size<2> m_id<0x90>
msdc <0> <HYNIX > <H4G1d>
msdc <1> <xxxxxx> <H4G1d>
msdc failed to find
*******EMMC_INFO*******
eMMC partition size(1 block = 512Bytes):
BOOT1:<4096> blocks
BOOT2:<4096> blocks
RPMB :<4096> blocks
GP1 :<0> blocks
GP2 :<0> blocks
GP3 :<0> blocks
GP4 :<0> blocks
USER :<7569408> blocks
*******EMMC_INFO*******
fw id len:1
found:1,i:1
[EMI] DDR2
[EMI] eMMC/NAND ID = 90,1,4A,48,34,47,31,64,4
[EMI] MDL number = 1
[MEM] 1066 MHZ
rank 0 coarse = 15
rank 0 fine = 48
10:| 0 0 1 1 1 0
opt_dle value:8
rank 1 coarse = 15
rank 1 fine = 48
10:| 0 0 1 1 1 0
opt_dle value:8
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,A)
byte:2, (DQS,DQ)=(8,8)
byte:3, (DQS,DQ)=(8,A)
[EMI] DRAMC calibration passed
[EMI] DQSINCTL:50000
[MEM] complex R/W mem test pass
[PLFM] Init Boot Device: OK(0)
[ROM_INFO] 'v2','0x2700000','0x20000','0x46C0000','0x2C00'
[SEC_K] SML KEY AC = 0
[SEC_K] SBC_PUBK Found
[SEC] AES Legacy : 0
[SEC] SECCFG AC : 1
[SEC] read '0x2700000'
0x41,0x4E,0x44,0x5F,0x53,0x45,0x43,0x43,
[LIB] SecLib.a '20121226-155014'
[LIB] CFG read size '0x4000' '0x1860'
[LIB] Name = SOMC
[LIB] Config = 0x11, 0x11
0x31,0x41,0x35,0x35
0x6F679858
[LIB] HW DEC
0x49494949
[LIB] SEC CFG 'v3' exists
[LIB] Status = 0x43434343
[LIB] ty = 0 , ld = 0
[PART] Image with part header
[PART] name : LK
[PART] addr : FFFFFFFFh
[PART] size : 316772
[PART] magic: 58881688h
[PART] load "UBOOT" from 0x0000000003960200 (dev) to 0x81E00000 (mem) [SUCCESS]
[PART] load speed: 9374KB/s, 316772 bytes, 33ms
[LIB] HW DEC
[SECRO] secroimg '0x41414141'
[SECRO] secroimg '0x35353535'
[SECRO] factory mode enabled
[AUTHEN] rsa.N length = 1024 bytes
[AUTHEN] rsa.E length = 20 bytes
[LIB] Verify 'UBOOT'
0x43434343
[LIB] part load '0x3960000'
[AUTHEN] 0x53,0x53,0x53,0x53
[AUTHEN] verify signature ... pass
[LIB] Verify 'LOGO'
0x43434343
[LIB] part load '0x4D40000'
[AUTHEN] 0x53,0x53,0x53,0x53
[AUTHEN] verify signature ... failed, error is 7
[SECLIB_IMG_VERIFY] Signature Fail.
[LIB] Fail (0x0)
<ASSERT> sec_boot.c:line 181 0
[PLFM] preloader fatal error...
[PLFM] emergency download mode(timeout: 30s).
mtk_arch_reset at pre-loader!
this is console with serial interface
i will post picture with pin layaut

how to unbrick?

botioni said:
[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=0 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=1 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=2 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=3 rdata=5AA5
[PMIC_WRAP]wrap_init pass,the return value=0.
pl pmic init start
pl pmic efuse start
pl pmic efuse BUCK trim
[0x1C8]=0xF802
[0x1CA]=0x807F
[0x20E]=0xE0
[0x260]=0xF0
[0x286]=0xF0
pl pmic efuse end
pl pmic en rst [0x126]=0x13
[0xE]=0x1
[0x540]=0xA0
Battery exist
[0xE]=0x1
[0x540]=0xA0
pl vm read [0x290]=0x50
pl vm set [0x290]=0x52
pl vm check [0x290]=0x52
pl pmic init done
[PLFM] Init I2C: OK(0)
[PLFM] Init PWRAP: OK(0)
[PLFM] Init PMIC: OK(0)
[PLFM] chip[CA00]
[I2C][PL] [i2c0 write] i2c transaction complate
[BLDR] Build Time: 20140218-141828
==== Dump RGU Reg ========
RGU MODE: 75
RGU LENGTH: FFE0
RGU STA: 40000000
RGU INTERVAL: FFF
RGU SWSYSRST: 0
==== Dump RGU Reg End ====
RGU: g_rgu_satus:2
mtk_wdt_mode_config mode value=35, tmp:22000030
PL RGU RST: ??
SW reset with bypass power key flag
Find bypass powerkey flag
mtk_wdt_mode_config mode value=70, tmp:22000071
kpd register for pmic set!
mt_usb_calibraion: input_reg = 0x0
mt_usb_calibraion: term_vref = 0x0, clkref = 0x0, vrt_vref = 0x0,
[RTC] bbpu = 0x5, con = 0x426
[RTC] irqsta = 0x0, pdn1 = 0x0, pdn2 = 0x201, spar0 = 0x40, spar1 = 0x800
[RTC] new_spare0 = 0x0, new_spare1 = 0x1, new_spare2 = 0x1, new_spare3 = 0x1
[RTC] bbpu = 0x5, con = 0x424
SW reset with bypass power key flag
SW reset with bypass power key flag
[PLFM] WDT reboot bypass power key!
p1 pmic read INT_RSV(bit7)[0x138][0x80]
[RTC] rtc_bbpu_power_on done
[SD0] Bus Width: 1
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(0) DDR(0) DIV(193) DS(0) RS(0)
[SD0] Switch to High-Speed mode!
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(2) DDR(1) DIV(96) DS(0) RS(0)
[SD0] Bus Width: 8
[SD0] Size: 3696 MB, Max.Speed: 52000 kHz, blklen(512), nblks(7569408), ro(0)
[SD0] Initialized
[SD0] SET_CLK(52000kHz): SCLK(50000kHz) MODE(2) DDR(1) DIV(0) DS(0) RS(0)
msdc_ett_offline_to_pl: size<2> m_id<0x90>
msdc <0> <HYNIX > <H4G1d>
msdc <1> <xxxxxx> <H4G1d>
msdc failed to find
*******EMMC_INFO*******
eMMC partition size(1 block = 512Bytes):
BOOT1:<4096> blocks
BOOT2:<4096> blocks
RPMB :<4096> blocks
GP1 :<0> blocks
GP2 :<0> blocks
GP3 :<0> blocks
GP4 :<0> blocks
USER :<7569408> blocks
*******EMMC_INFO*******
fw id len:1
found:1,i:1
[EMI] DDR2
[EMI] eMMC/NAND ID = 90,1,4A,48,34,47,31,64,4
[EMI] MDL number = 1
[MEM] 1066 MHZ
rank 0 coarse = 15
rank 0 fine = 48
10:| 0 0 1 1 1 0
opt_dle value:8
rank 1 coarse = 15
rank 1 fine = 48
10:| 0 0 1 1 1 0
opt_dle value:8
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,A)
byte:2, (DQS,DQ)=(8,8)
byte:3, (DQS,DQ)=(8,A)
[EMI] DRAMC calibration passed
[EMI] DQSINCTL:50000
[MEM] complex R/W mem test pass
[PLFM] Init Boot Device: OK(0)
[ROM_INFO] 'v2','0x2700000','0x20000','0x46C0000','0x2C00'
[SEC_K] SML KEY AC = 0
[SEC_K] SBC_PUBK Found
[SEC] AES Legacy : 0
[SEC] SECCFG AC : 1
[SEC] read '0x2700000'
0x41,0x4E,0x44,0x5F,0x53,0x45,0x43,0x43,
[LIB] SecLib.a '20121226-155014'
[LIB] CFG read size '0x4000' '0x1860'
[LIB] Name = SOMC
[LIB] Config = 0x11, 0x11
0x31,0x41,0x35,0x35
0x6F679858
[LIB] HW DEC
0x49494949
[LIB] SEC CFG 'v3' exists
[LIB] Status = 0x43434343
[LIB] ty = 0 , ld = 0
[PART] Image with part header
[PART] name : LK
[PART] addr : FFFFFFFFh
[PART] size : 316772
[PART] magic: 58881688h
[PART] load "UBOOT" from 0x0000000003960200 (dev) to 0x81E00000 (mem) [SUCCESS]
[PART] load speed: 9374KB/s, 316772 bytes, 33ms
[LIB] HW DEC
[SECRO] secroimg '0x41414141'
[SECRO] secroimg '0x35353535'
[SECRO] factory mode enabled
[AUTHEN] rsa.N length = 1024 bytes
[AUTHEN] rsa.E length = 20 bytes
[LIB] Verify 'UBOOT'
0x43434343
[LIB] part load '0x3960000'
[AUTHEN] 0x53,0x53,0x53,0x53
[AUTHEN] verify signature ... pass
[LIB] Verify 'LOGO'
0x43434343
[LIB] part load '0x4D40000'
[AUTHEN] 0x53,0x53,0x53,0x53
[AUTHEN] verify signature ... failed, error is 7
[SECLIB_IMG_VERIFY] Signature Fail.
[LIB] Fail (0x0)
<ASSERT> sec_boot.c:line 181 0
[PLFM] preloader fatal error...
[PLFM] emergency download mode(timeout: 30s).
mtk_arch_reset at pre-loader!
this is console with serial interface
i will post picture with pin layaut
Click to expand...
Click to collapse
how did you check this out?

theonecallednick said:
how did you check this out?
Click to expand...
Click to collapse
I found uart pin on mainboard for debuging .
with serial usb cable pl2303

This is the red light only and unknown hardware found (the unknown hardware is in fact mtk usb vcom driver buth sony version ) if you try sp flash tool for mtk then it comunicates with de phone buth it needs some authentication file.

Help..
I am also having same problem..I falshed wrong rom..
It just shows red led and does not detects by PC...
Were you able to solve the problem..if yes..please help..

botioni said:
[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=0 rdata=5AA5
.........................
this is console with serial interface
i will post picture with pin layaut
Click to expand...
Click to collapse
Samuel Wankhede said:
I am also having same problem..I falshed wrong rom..
It just shows red led and does not detects by PC...
Were you able to solve the problem..if yes..please help..
Click to expand...
Click to collapse
Try the guide given in thread linked below
http://forum.xda-developers.com/showpost.php?p=57614511&postcount=13

Please share uart pinout
Baudrate should be 115200??
Thanks

uart
please share the uart pinout , thanks

Allwinner A31 H4 Hummingbird Kit

Hi
Around for months ago I buy from Aliexpress "Merrii H4" board.
Then it was delivered, I try to use it... Connect power cord, connect VGA display, power on.... and see - nothing. For I wiil right at all, I see "wrong resolution" OSD message. I use my PHILIPS 223V display, I try to connect HDMI thru HDMI->DVI converter, see - nothing, and display "freezing" not answer to any button, POWER included.
I connect UART->USB converter and have a look boot LOG, it's right... I can read how system (android 4.4) started, I see info about screen resolution (800x480)
But... I want to do something else. I'm already try to communicate with merrii support... it is terrible... Hi talking with me, like I'm a stupid guy with no any skill and ... it is very very slow... Hi is answer to me two...three times per day, and him answer not helpfull.
NOW I'm already try to use PhoenixSuite 1.0.6, 1.0.8, 1.10 and PhoenixSuitePro 3.3.0, 3.3.4 to replace firmware, I can't do it, programm can't open iimages what I have...
sun6i_android_fiber-3g_v3.3_hummbingbird__TP_WIFI_BT_TV-IN_VGA_USB_OTG_3G_TCARD_RTC_OK_测试.img
sun6i_android_fiber-3g_v3.3_hummbingbird__LCD_TP_WIFI_BT_USB_OTG_CAMERA_3G_GMAC_TFCARD_RTC_ok_出货.img
what I do: run programm, press the UBOOT button and then plug USB cable, nothin is action with PS, and PSPro say "bla bla bla.. don't connect any device before ..."
When I try to open IMG file in PS, programm say "can't open Image"
When I open IMG file in PSPro and press START button after, nothing
Have I any luck to Sombody can help my situation?
I want to use my board with SOMETHING display for the begin.... And after I want to use it with 12.3" screen in my car.

boot LOG
<0>HELLO! BOOT0 is starting!
boot0 version : 3.0.0
reg_addr 0x01f00HELLO! BOOT0 is starting!
boot0 version : 3.0.0
reg_addr 0x01f00100 =0x00000000
reg_addr 0x01f00104 =0x00000000
reg_addr 0x01f00108 =0x00000000
reg_addr 0x01f0010c =0x00000000
reg_addr 0x01f00110 =0x00000000
reg_addr 0x01f00114 =0x00000000
[DRAM]ver 1.03 clk = 240
cpu 3 pmu 0
dram size =1024
sum=0xc0fe9d5b
src_sum=0xc0fe9d5b
Ready to disable icache.
[ 0.216]
0.231]PMU: AXP22x found
[ 0.234]PMU: bat ratio = 100
[ 0.237]PMU: dcdc3 1260
40]PMU: pll1 1008 Mhz
dcdc1_vol = 3000
fel key old mode
ram_para_set end
[ 0.284]DRAM: 1 GiB
relocation Offset is: 15b25000
[ 0.284]DRAM: 1 GiB
relocation Offset is: 15b25000
tart
eyB
:boot_init_gpio)
relocation Offset is: 15b25000
tart
dol = 1200
dcdc5_vol = 1500
aldo1_vol = 3000
aldo2_vol = 1800
deu_mode1 not exist.
exist.
aldo3_vol = 3000
eldo3_vol = 1800
find power_sply to end
200
ist.
lcdgamma4iep for lcd1 not ocation Offset is: 15b25000
tart
DRV_DISP_Init: opened
[ 0.559]fetch script data boot_disp.output_type fail
0.574]lcd0_para.lcd_used=1
[ 0.564]fetch script data boot_disp.output_mode fail
[ 0.569]fetch script data boot_disp.auto_hpd fail
tput_mode fail
[ 0.569]fetch script data boot_disp.auto_hpd fail
workmode = 0
B1 : nftl num: 2
init nftl: 0
: 2
init nftl: 0
ND_UbootInit
NB1 : enter NAND_LogicInit
not burn nand partition table!
[ 3000
NAND_LogicInit
not burNB1 : NAND_LogicInit ok, result = 0x0
[ 1.250]sunxi flash init ok
[mmc]: cmd 8 timeout, err 100
[mmc]: mmc cmd 8 err 0x00000100
: mmc cmd 1 err 0x00000100
mmc send op cond failed
-------fastboot partitions--------
data : 34000000 80000000
2000000
bootcmd set setargs_nand
s_probe
to stop autoboot: 0
read boot or recovery all
=====hanbiao 111===: start=18000, addr=40007800
autoboot: 0
read boot or recovery all
=====hanbiao 111===: start=18000, addr=40007800
WORK_MODE_BOOT
boot or recovery all
=====hanbiao 111===: start=18000, addr=40007800
WORK_MODE_BOOT
ot: 0
read boot or recovery all
=====hanbiao 111===: start=18000, addr=40007800
WORK_MODE_BOOT
[ 1.387]Hit any key oard_statu-------------------------
ll
=====hanbiao 111===: start=18000, addr=40007800
WORK_MODE_BOOT
recovery all
=====hanbiao 111===: start=18000, addr=40007800
WORK_MODE_BOOT
[ 1.387]Hit any key oard_statu-------------------------
base bootcmd=run setargs_nand boot_normal0
===hanbiao 111===: start=18000, addr=40007800
WORK_MODE_BOOT
111===: start=18000, addr=40007800
WORK_MODE_BOOT
[ 1.387]Hit any key oard_statu-------------------------
art=18000, addr=40007800
WORK_MODE_BO=====hanbiao 222===: start=18040, addr=4000f800
[ 1.915]sunxi flash read ffset 3000000, 11201530 bytes OK
dy to boot
NAND_UbootExit
NB1 : NAND_LogicExit
[ 1.926]
Starting kernel ...
signature pass
[ 1.923]rea<6[ 0.915214] aw_pm_init: not support super standby.
[ 0.979688] sun6i_vibrator_fetch_sysconfig_para motor is not used in config
[ 1.604963] otg_wakelock_init: No OTG transceiver found
[ 4.072052] init: /init.sun6i.rc: 45: invalid command 'umount'
[ 4.272611] init: /dev/hw_random not found
[ 6.614276] init: width = 800
[ 6.617579] init: height = 480
[ 6.620973] init: s.st_size = 1536000
[ 6.633434] init: dont need format /dev/block/by-name/UDISK
[ 8.007838] init: /dev/hw_random not found
[ 8.031591] healthd: wakealarm_init: timerfd_create failed
[ 8.043859] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 8.054414] init: cannot find '/system/bin/usb_scan', disabling 'ttyusb-scan'
[ 8.184908] android_usb: already disabled
[email protected]:/ $ [ 10.162964] gslX680 1-0040: read failed
[ 10.367857] init: untracked pid 1764 exited
[ 24.838266] init: sys_prop: permission denied uid:1003 name:service.bootanim.exit
Click to expand...
Click to collapse