Possibly soft bricked. - HTC Inspire 4G

I did search, but in all honesty Im not really sure what Im looking for. Yesterday I rooted with the Ace Hack. Then today I was looking through Rom Manager, and I downloaded cyanogenmod, and when it finished it wanted to load it, so I let it. Ive done two backups prior to this. Now when I turn it on the white HTC screen comes up, then it goes to the cyanogenmod 7 screen, skateboarding android with a ring around him and a loading arrow. And thats all it does, over and over. Is there a way to boot to the backups? A certain button combonation I should be using? Specific terms I should search for? Please, at least, point me in the right direction.

slipmagt said:
I did search, but in all honesty Im not really sure what Im looking for. Yesterday I rooted with the Ace Hack. Then today I was looking through Rom Manager, and I downloaded cyanogenmod, and when it finished it wanted to load it, so I let it. Ive done two backups prior to this. Now when I turn it on the white HTC screen comes up, then it goes to the cyanogenmod 7 screen, skateboarding android with a ring around him and a loading arrow. And thats all it does, over and over. Is there a way to boot to the backups? A certain button combonation I should be using? Specific terms I should search for? Please, at least, point me in the right direction.
Click to expand...
Click to collapse
You'll need to do a complete wipe to install CM over an existing sense build. Sense stores the dalvik on the data partition and CM7 stores it on the cache partition. If you don't do a full wipe, then the dalvik never gets set up properly.
You should still be able to get into cwm recovery via hboot. Make sure phone is off (pull battery if necessary). Hold VOL-DOWN button while pressing power for about a second. You should end up in the HBOOT screen. Select recovery and press power. Hopefully CWM recovery will boot up and you can just do a "Wipe data/Factory Reset" and be good.

I had just found out how to boot to recovery seconds before I checked the thread again. Instead I went to backup and recover, and restored from a backup, and it didnt work. So I am trying what you suggested, I really appreciate you giving me all the steps required.
I may have told it to not delete the dalvik when it wanted to start up cyanogenmod.

So what is the best way to download roms and switch between them?

slipmagt said:
So what is the best way to download roms and switch between them?
Click to expand...
Click to collapse
1 suggestion...ditch rom manager. I've had issues before where it messed up my downloads. Not everyone has this issue I will say, but I would try not using it. All the devs update their threads here on xda with the latest versions in their threads. Download them from the site, boot into recovery,back up your current rom, and flash away!
I got your 10 char right here

cwhitney24 said:
1 suggestion...ditch rom manager. I've had issues before where it messed up my downloads. Not everyone has this issue I will say, but I would try not using it. All the devs update their threads here on xda with the latest versions in their threads. Download them from the site, boot into recovery,back up your current rom, and flash away!
I got your 10 char right here
Click to expand...
Click to collapse
Agreed. I've never used RomManager with the Inspire, but I had nothing but problems with it on my Aria.

It gone. How do you switch between roms then?

slipmagt said:
It gone. How do you switch between roms then?
Click to expand...
Click to collapse
Like I said above...use the threads to find the roms. Download them and flash them in recovery. ALWAYS create a back up so you can flash back to your back ups if you want. All that can be done in recovery.
If you do not know how to do this then my thoughts on why rom manager exists are true. Search the threads and learn how to do all the fun stuff without rom manager and without needing someone to hold your hand. (Wasn't being mean just a figure of speech)
I got your 10 char right here

Related

The officially unofficial Tiamat Moray ROM Q&A Thread

This thread is an attempt to help out the Tiamat Developers by answering the frequently asked questions in one consolidated thread. This thread should also be helpful to those who either cannot use the search feature or are having a hard time figuring out the correct search terms to find what they are looking for. If you have suggestions or added questions/answers feel free to reply and I will update the OP.
NOTE: I am not a developer. All of the information in this thread is from other members who have helped me out or information I found in the XDA forums. I do not take credit for any of the great work that has been done on this ROM and I will point back to the original answer when possible. I am only trying to help lessen the burden on the developers so they can spend more time getting us the best features. Hopefully you find this helpful as well.
I've flashed this ROM and now I get update notifications. Should I accept the update? How do I stop these notifications?
No, you should never accept an OTA upgrade when using any custom ROM/Kernel. This could result in severe problems. Your best bet is to be patient and give the developers time to react. If the update is worthwhile I am sure they will roll it out pretty quickly.
To get rid of the notifications flash Mod pack 3 as noted here.
OK I made the mistake of accepting the OTA update and now my Xoom won't boot. What can I do?
okantomi said:
Can you make it reboot by pressing volume up and power at the same time and holding? If it reboots, wait about 3 seconds once you see the dual core logo and then tap volume down you shoud see android recovery, then tap up to choose it. I hope you did a nandroid backup. If not, you can try and get fastboot by tapping volume down sooner after it reboots.
Click to expand...
Click to collapse
From this thread.
With this ROM certain websites don't load correctly or I can't get to the mobile version of a site.
This ROM by default sets the User Agent String to "desktop". If you want to revert to the stock settings flash either Mod pack 1 or 2 depending which version of Moray you are running. Look here.
I flashed this ROM and now when I click links in email or my file explorer the screen just dims and nothing happens.
This is a bug in Android 3.2 and not specific to this ROM. To solve this, simply ensure auto-rotate is enabled and rotate the device from landscape to portrait and back to landscape. The app chooser window should appear allowing you to choose which app to open the selected file.
I just flashed this ROM and the speed is amazing, so I OC'd it to 1.7GHz cuz I want more and I am now stuck in a boot loop. This worked for others why not me?
The Xoom was only specified to run at 1.0 GHz, anything beyond that is a gift. Due to part-to-part variation not everyone's Xoom will be stable at the same speed. Yes some people are able to run at 1.7 GHz, but many cannot. For your specific Xoom try out the various speeds, but do NOT click "Set on Boot". This way if it crashes it will revert back to stock speed and you will be able to boot. Once you are satisfied with a speed then feel free to enable "Set on Boot". Before you do so I would suggest making a nandroid backup so you can restore just in case.
How do you get out of this boot-loop? The only way I know of is to boot into recovery and restore a nandroid backup if you have one or perform a full wipe if you do not.
I updated to the latest CWM and I cannot find the zip card or I get "get error: E:failed to mount /sdcard (No such file or directory)."
Latest is not always the best, for the Xoom you need to either use ClockworkMod 3.2.0.0 (R4C) or CMW Rogue Recovery v1.1.1
After flashing this ROM the Motorola icon gets distorted during boot up, is that a problem?
Basically it is not a problem. This kernel has a patch provided by NVidia which causes the distortion during boot. It does not cause any problems after it boots.
Is there a way to get the stock WiFi and Battery icons?
Yes
How do I boot into recovery without ADB or my PC attached?
There are a couple methods.
1) The latest Tiamat ROM includes this if you press and hold the power button. Just pick what you want and hit OK.
2) Download and install "Quick Boot" from the market. It gives you the above options as well as others when you run the app.
3) Turn the Xoom on, wait ~2 seconds after your see the Dual Core logo, then press the volume down key. In the upper left corner it should say "Android Recovery", then press the volume up key to select it.
How do I get started? Any good guides?
There are several guides that are pretty good. The best one I have found and personally used is here.
The Xoom Heaven thread found here is also a good place to start for all sorts of information.
If you have another question please feel free to post to this thread. If you are having a problem or have a question it is likely that someone else along the lines will have the same problem or question. I will continue to update this OP with the list of F.A.Q.s.
Additional Q&As
After installing this ROM I am having issues with the market not finding all of my apps or apps are giving errors when trying to install them.
See this post for one possible solution.
One more for good measure...
HuckFinn, I think you have covered most of the hot issues. Great job!
Stickied. Thanks for posting this, and Solarnz for giving me the heads up to do so.
Sorry for the newb question, but what's "root"?
Psychokitty said:
Sorry for the newb question, but what's "root"?
Click to expand...
Click to collapse
oh kitty, you funny!
Psychokitty said:
Sorry for the newb question, but what's "root"?
Click to expand...
Click to collapse
It's what you pull your hair out by when something is not working properly!!
darn you... I earned 1/2 my posts responding to the "why does my screen dim" question... now I'll have nothing to say!
i performed a factory reset from the os-> settings and once again performed a wipe/factory reset from the cwm recovery but still can't get back to the initial setup screen (where you enter your google a/c, etc)
any idea?
Thanks!!
Here is one..
Why does Market show up in USD even though my locale is set to UK, my language is English British along with my keyboard layout?
Ive had boot loops twice. Both times i could get into recovery but could not get backup to restore . kept getting cant read /sdcard. also cant reinstall update .zip becuase the sd card wont mount. I have only gotten back in by letting it sit powered off for a bit.
any ideas?
should i adb a stock image and start again?
should i flash a different recovery?
madamimadam said:
Ive had boot loops twice. Both times i could get into recovery but could not get backup to restore . kept getting cant read /sdcard. also cant reinstall update .zip becuase the sd card wont mount. I have only gotten back in by letting it sit powered off for a bit.
any ideas?
should i adb a stock image and start again?
should i flash a different recovery?
Click to expand...
Click to collapse
What version of recovery is installed now? If you have the version that doesn't recognize your external sdcard you should certainly flash a compatible recovery version through fastboot.
okantomi said:
What version of recovery is installed now? If you have the version that doesn't recognize your external sdcard you should certainly flash a compatible recovery version through fastboot.
Click to expand...
Click to collapse
Is there a way to check version without booting into recovery? Which version would you suggest?
And thank you
madamimadam said:
Is there a way to check version without booting into recovery? Which version would you suggest?
And thank you
Click to expand...
Click to collapse
There are only two recoveries compatible..
you will find them in the Xoom Android Developmet Board in the sticky threads
LPHS said:
There are only two recoveries compatible..
you will find them in the Xoom Android Developmet Board in the sticky threads
Click to expand...
Click to collapse
OR here:http://forum.xda-developers.com/showthread.php?t=1209341
Links to both of these recoveries are also in the first post of this thread.
HuckFinn said:
Links to both of these recoveries are also in the first post of this thread.
Click to expand...
Click to collapse
Guess I should have read the thread before posting here, sorry for being a troll.
I tried this ROM on my 4G Xoom, but it left me without 4G or 3G (wifi only). Any way to get this working, or do I have to wait for an update?
I did try activating the network in settings, but it never connected even half an hour.
Thanks to steps mentioned by user 'LordDeath' in another thread and a bit of experimenting with a rooted 4G Xoom and a friends 3G Xoom running Moray, there seems to be a remedy for those who are having issues with the market compatibility issues as well as missing apps. I did not activate until attempting to sign in to the market and had missing apps and compatibility issues. I simply did a full wipe & reset and made sure the full activation went through in set up then let it automatically start restoring. I took a peek in the market after a a minute and all my apps were back with no compatibility issues. Here is a copy of his original post and mine but the last step was not needed for me.
Originally Posted by LordDeath
Something more about the market:
After I restored my backup of the official 3.1 ROM I still had some issues. On http://market.android.com I still saw that my Xoom is not compatible with some apps. The market app on the device did show these apps but upon installing I got the error message: "Fehler beim Verarbeiten des Kaufs". Translated into English it means "Error while processing the purchase". It was a free app, btw.
To solve this issue I did the following:
1. Wipe data/factory reset
2. Active the device during the wizard on the first boot with my Google account
3. Restore the nandroid backup of the official 3.1 ROM
Therefore it seems that the market servers check your device-compatibility only during the activation process at the first startup.
----------------------------------------------------------------------------
"This fixed everything for my friend running Moray and even corrected the issues on my 4G Xoom..."
I should add that though this fixes the issue, if you change your pixel density you may run into similar issues but can correct it by setting it back to 160 before going into the market.

[Q] now that I have root, is it different to get CWM?

easier perhaps? I read about a rom manager you download from the market...
Thanks to what efforts everyone contributes here, I've found after getting out of soft brick, I managed to get root. And I'm almost happy with the handset, now that I got root explorer to work. It works best as a browser for the 20 gigs of junk on my sd card, I've found.
What I have is the SGH-i727 att branded, returned to stock, 2.3.5, my kernel is 2.6.35.11 also I flashed something in the i777 forum, is the reason for "returned to stock". My handle could be adjusted to "stupidbiker". And I've been properly scolded.
So what's a good way to get clockwork mod in my situation?
And I don't care about a warranty or a counter, or does the counter do other bad things?
And a link for operating clockwork mod? Everyone here can push three buttons except me! LOL I've pulled it off a few times on accident, but I bet in here somewhere there is a correct procedure outlined for operating clockworkmod. A link to that would be way cool.
Wow I'm stupid. K. Thanks.
This is question and answer right? I got lots of questions!
Once I get clockworkmod in the device with all the colors, I'm gonna flash a rom, the ice cream rocket I saw, also I want to test CM7, I'm in L.A. and in the LTE area and looks like I could provide input.
I'm using search, but if someone plants a good link it would be much appreciated.
Thanks.
fukenbiker said:
easier perhaps? I read about a rom manager you download from the market...
Thanks to what efforts everyone contributes here, I've found after getting out of soft brick, I managed to get root. And I'm almost happy with the handset, now that I got root explorer to work. It works best as a browser for the 20 gigs of junk on my sd card, I've found.
What I have is the SGH-i727 att branded, returned to stock, 2.3.5, my kernel is 2.6.35.11 also I flashed something in the i777 forum, is the reason for "returned to stock". My handle could be adjusted to "stupidbiker". And I've been properly scolded.
So what's a good way to get clockwork mod in my situation?
And I don't care about a warranty or a counter, or does the counter do other bad things?
And a link for operating clockwork mod? Everyone here can push three buttons except me! LOL I've pulled it off a few times on accident, but I bet in here somewhere there is a correct procedure outlined for operating clockworkmod. A link to that would be way cool.
Wow I'm stupid. K. Thanks.
This is question and answer right? I got lots of questions!
Once I get clockworkmod in the device with all the colors, I'm gonna flash a rom, the ice cream rocket I saw, also I want to test CM7, I'm in L.A. and in the LTE area and looks like I could provide input.
I'm using search, but if someone plants a good link it would be much appreciated.
Thanks.
Click to expand...
Click to collapse
download rom manager, install cwm from that, select tmobile galaxy s2 when asked.
see what I found
First you need to flash Clockworkmod Recovery. Then you place the zip on your SDcard, do a Nandroid backup through clockworkmod Recovery (not necessary but highly, highly recommended... especially if you have never done this before.) Then select install zip from SD card, find the .Zip file and run it and you should be golden.
What is nandroid? I use Mybackup Pro. Same sort of stuff right? I'm getting close to getting my arms around everything....
waiters said:
download rom manager, install cwm from that, select tmobile galaxy s2 when asked.
Click to expand...
Click to collapse
Thank you for such a quick reply. I am on AT&T. Why would I select Tmobile?
"because that's the one that works"
is an answer I can accept. I'm not fussy just stupid.
Thank you!
I have successfully flashed ClockworkMod Recovery using ROM Manager. I'm so pleased I'm gonna get premium. I see directions! It shows a button for flashing a custom rom that I store on my SD card? Do I dare?
I picked the tmobile thing and so far so good. I got data and just tried a phone call. Happy.
I will follow the other threads now. If a moderator thinks people will get more stupid reading my new thread they may delete it.
I soft bricked
figured out Odin enough to flash back to stock
got root
went to market and installed ROM Manager
turned on wifi as ROM Manager recommended
after a good hookup, I flashed ClockworkMod recovery
Surfed the web, made a phone call, took a picture, uploaded to facebook
Looks like I'm all good.
I'm feeling ready...
fukenbiker said:
Thank you for such a quick reply. I am on AT&T. Why would I select Tmobile?
"because that's the one that works"
is an answer I can accept. I'm not fussy just stupid.
Click to expand...
Click to collapse
apparently they are very similar (but dont get crazy and start installing the tmobile gs2 kernel/roms) - also there is no skyrocket version yet...
but yes cwm does work perfectly from rom manager when you select tmobile gs2
i did this myself the other day... works fine..
just download rom manager, have fun.. good luck
hey ****enbiker would you say your kinda ''noobish'' when it comes to this ? lol I'm just super scared to do this. To avoid voiding my warranty I was even thinking of just saving a check and getting a nexus s to fool around with, but if your new to this and would say ''ALMOST anyone can do it'' I'd say I might be game. I just would like to learn somethings from newer rooters rather than annoy/piss off the Vets!
I have screwed up every phone I got my hands on so not a noob exactly. I am at present using cm7 and considering the new kernel released this morning. What's holding me back is how well it works and how easily I screw up and screen rotation work around is good enough so why flash and set up again... oh I will flash again but just got it all restored back and gotta take it to work tomorrow ...
Yeah pretty much if I can do it anyone can. I really am ignorant compared to a programmer or developer. But not many noobs have broken as much stuff as I have!
Sent from my SGH-I727 using xda premium
Boot into CWM?
waiters said:
apparently they are very similar (but dont get crazy and start installing the tmobile gs2 kernel/roms) - also there is no skyrocket version yet...
but yes cwm does work perfectly from rom manager when you select tmobile gs2
i did this myself the other day... works fine..
just download rom manager, have fun.. good luck
Click to expand...
Click to collapse
I am having trouble getting CWM to boot on device start-up with the Vol Up Key, is this how you do it or am I doing it wrong?
I can easily get to it from choosing "Reboot into Recovery" from ROM manager but I want to make sure I can get in without Android in case I need to do a full NAND recovery.
Thanks
promiseofcake said:
I am having trouble getting CWM to boot on device start-up with the Vol Up Key, is this how you do it or am I doing it wrong?
I can easily get to it from choosing "Reboot into Recovery" from ROM manager but I want to make sure I can get in without Android in case I need to do a full NAND recovery.
Thanks
Click to expand...
Click to collapse
its volume UP and DOWN......
the2rrell said:
its volume UP and DOWN......
Click to expand...
Click to collapse
Wow OK I thought I tried that, anyway it worked! Thanks a lot.
Sent from my SAMSUNG-SGH-I727 using XDA App
YouTube stutters on CM
Okay after I finally settled in with version 4 I have figured out that version 3 it was okay YouTube did not stutter or jerk, it is this new Da_G's kernel when the video went to hell. I remember the problem appeared in version 3 after flashing Da_G's kernel.
I have not tried any other kernel beside Da_G's with version 4. And YouTube is skippy jerking all to our dismay here. Or there, where ever I was to report this, beg pardon.
Sent from my SGH-I727 using xda premium
edit:
I see you don't have to press the power button?
I always begin that way, I press all three at once.
Volume up, volume down, and power.
After it buzzes three times I keep the volume up and down held, but let go of the power button.
I keep the volume up and down held until I see a logo on the screen. Then I let go of the phone and it boots into the scarey black screen with dos writing and you have to navigate with the hardware buttons.
That's how I've been doing it and it puts me into cwm recovery straight from putting the battery back in, every time.
If a true noob is reading this, you're dropping in after I've rooted and then obtained clockworkmod from the market, granted it superuser permissions, and then, after getting past the advertisements, you select to flash clockworkmod.
Also you'll see discussion of not getting a signal and getting an APN. Before you try CyanogenMod or CM7, which is what I use, you take your handset that has a working signal, and download an app from the market called "APN backup and restore" and do a backup of your APN. (not for those who refuse to populate the phone with a chip) (also not for those who don't have a working wifi readily available) Now make sure you have a copy of that on the other chip. The Skyrocket has an internal SD and also an external SD which ATT turns out is too cheap to put one in there when they sell it...
Make sure you have ApnBackupRestore folder with it's xml content on both chips.
Then go to CM7, in the op, get version 4, then go to the kernel thread and get Da_G's kernel, and put them on BOTH sd cards (so you won't have trouble finding it LOL)
And there you have it. Yet another blue collar attempt at helping folks that are smarter than I am that aren't as brave as I am!
Pull the battery, and apparently only hold the two volume buttons after putting the battery back in, never tried it that way! Wipe Data/Factory reset, find the rom and install it, find the kernel and flash that zip as well (install it, trying to help with lingo) reboot, then hook up to wifi, download APN backup/restore from the market (your phone will sync and load it for you when you log in with your google gmail to set up the handset. Run the APN backup and restore app and enjoy CyanogenMod!
My favorite, can you tell, LOL
fukenbiker said:
Okay after I finally settled in with version 4 I have figured out that version 3 it was okay YouTube did not stutter or jerk, it is this new Da_G's kernel when the video went to hell. I remember the problem appeared in version 3 after flashing Da_G's kernel.
I have not tried any other kernel beside Da_G's with version 4. And YouTube is skippy jerking all to our dismay here. Or there, where ever I was to report this, beg pardon.
Sent from my SGH-I727 using xda premium
edit:
I see you don't have to press the power button?
I always begin that way, I press all three at once.
Volume up, volume down, and power.
After it buzzes three times I keep the volume up and down held, but let go of the power button.
I keep the volume up and down held until I see a logo on the screen. Then I let go of the phone and it boots into the scarey black screen with dos writing and you have to navigate with the hardware buttons.
That's how I've been doing it and it puts me into cwm recovery straight from putting the battery back in, every time.
If a true noob is reading this, you're dropping in after I've rooted and then obtained clockworkmod from the market, granted it superuser permissions, and then, after getting past the advertisements, you select to flash clockworkmod.
Also you'll see discussion of not getting a signal and getting an APN. Before you try CyanogenMod or CM7, which is what I use, you take your handset that has a working signal, and download an app from the market called "APN backup and restore" and do a backup of your APN. (not for those who refuse to populate the phone with a chip) (also not for those who don't have a working wifi readily available) Now make sure you have a copy of that on the other chip. The Skyrocket has an internal SD and also an external SD which ATT turns out is too cheap to put one in there when they sell it...
Make sure you have ApnBackupRestore folder with it's xml content on both chips.
Then go to CM7, in the op, get version 4, then go to the kernel thread and get Da_G's kernel, and put them on BOTH sd cards (so you won't have trouble finding it LOL)
And there you have it. Yet another blue collar attempt at helping folks that are smarter than I am that aren't as brave as I am!
Pull the battery, and apparently only hold the two volume buttons after putting the battery back in, never tried it that way! Wipe Data/Factory reset, find the rom and install it, find the kernel and flash that zip as well (install it, trying to help with lingo) reboot, then hook up to wifi, download APN backup/restore from the market (your phone will sync and load it for you when you log in with your google gmail to set up the handset. Run the APN backup and restore app and enjoy CyanogenMod!
My favorite, can you tell, LOL
Click to expand...
Click to collapse
Whoa!!!!! COOL STORY BRO.............LOL
I'm sure this will help someone.
Sent from my SAMSUNG-SGH-I727 using xda premium
I don't know for sure, about the vol. up/dn.. but when I rooted my phone, the only way that I could get it to work was power & volume DOWN only. The three button just got me no where.
Sent from my SGH-I727R using xda premium

[Q] Infuse isnt listed in CWM

Im sure this isnt the first time this ha been asked, but i couldnt find it. I have an rooted infuse(AT&T), when trying to flas a new ROM it tells me that i need to flas CWM. I try to but it asks me to confirm phone model, the infuse is not listed. I havent picked another phone from the list because i didnt want to brick this one. Anybody know what might be wrong and how to fix it. THANKS
ACESFULL82 said:
Im sure this isnt the first time this ha been asked, but i couldnt find it. I have an rooted infuse(AT&T), when trying to flas a new ROM it tells me that i need to flas CWM. I try to but it asks me to confirm phone model, the infuse is not listed. I havent picked another phone from the list because i didnt want to brick this one. Anybody know what might be wrong and how to fix it. THANKS
Click to expand...
Click to collapse
Aces, I'm think you're in danger of soft bricking your phone.
Try to read up a bit before you go on.
You need to select Samsung I9000 from the list.
Sent from my SAMSUNG-SGH-I997 using xda premium
ACESFULL82 said:
Im sure this isnt the first time this ha been asked, but i couldnt find it. I have an rooted infuse(AT&T), when trying to flas a new ROM it tells me that i need to flas CWM. I try to but it asks me to confirm phone model, the infuse is not listed. I havent picked another phone from the list because i didnt want to brick this one. Anybody know what might be wrong and how to fix it. THANKS
Click to expand...
Click to collapse
Um....what are you doing? With CWM you're not using the ROM manager app right? You want to get into red recovery, that's what most instructions are talking about when they say cwm.
To get there: (if you have it)
Power off, then hold power button and volume up and down. (3 button)
Keep held, Samsung will come on, then turn off, when it comes on again let go of the buttons....should go into red recovery. That's where to flash roms from. Good luck.
X,
Sent from Mt. Olympus
yup. Pick i9000 and flash. also check out GTG's Infused ROM OP!! VERY useful info to get you started.
other than people telling you to read this whole thread fails.
OK you can use cwm from rom manager for the i9000. but first you need to replace the recovery binary with a modded one. that needs root.
search dev section on cwm fully working... or something to that matter. also search YouTube. YouTube is great for any type of DIY activity including Modding your phone.
there is an alternative to this by flashing the community kernel or the defuse kernel in Odin or heimdall. that not only doesn't need root but will root your phone, enable voodoo lagfix, and give you red cwm. there is a one click heimdall package for the defuse kernel. personally I disable voodoo beforehand to speed up the process. to do this open the sdcard and create a folder and subfolder having the path /sdcard/Voodoo/disable-lagfix
to be clear you don't create /sdcard that already exists. it is the root of the SD card. if you use the built in file manager it wont show as /sdcard but will be "home" or something.
so open my files or other file manager, navigate to home which is normally the sd card, if not navigate to /sdcard and create a folder named "Voodoo" capital "V" then open Voodoo and create "disable-lagfix" once that is done you can flash the defuse kernel or the community kernel. then flash a rom then if it all goes well reboot into red cwm and enable lagfix and reboot again. it takes a while and the phone talks to you in sexy female robot voices for a while.
Thanks all. Maybe im in over my head a little. Ive been playing my my inspire 4G and it has been working fine(knock on wood), flashed several ROMS. I will read a little more into it and try what yall said to do. Thanks everybody
ACESFULL82 said:
Thanks all. Maybe im in over my head a little. Ive been playing my my inspire 4G and it has been working fine(knock on wood), flashed several ROMS. I will read a little more into it and try what yall said to do. Thanks everybody
Click to expand...
Click to collapse
I never had an inspire but there is no way this is harder. there is no locked nand on Samsung devices. just a weird recovery that is easy to work around on froyo since it was so easy to root. future devices will get increasingly hard but you have to understand that Samsung isn't taking anti-flashing measures like HTC and Motorola it is security measures to prevent exploits for being used in malware, things are getting harder because it is getting harder to root android. at some point the only way to flash is gonna be to wait for a leaked rom, edit the images and then flash. or some complicated way we haven't seen yet.
ACESFULL82 said:
Thanks all. Maybe im in over my head a little. Ive been playing my my inspire 4G and it has been working fine(knock on wood), flashed several ROMS. I will read a little more into it and try what yall said to do. Thanks everybody
Click to expand...
Click to collapse
np.
IF you're looking to go from froyo to a gb rom,
I suggest starting here:
http://forum.xda-developers.com/showthread.php?t=1331381
learning how to flash with heimdall is pretty simple.
Flash it once in download mode. Flash it again with the bootloaders box checked.
reboot and you're in uckj4.
Then flash the kernel to give you recovery
then flash the gb rom you want...
there are other methods...it's a matter of prefs

[GUIDE] T-Mobile US One S - How to ROOT and flash ROMs

So I know there's been some controversy and scares going around about the US version, since it JUST came out. I'm here to calm you guys down. I have now rooted mine, flashed an interim CWM touch version (not permanent) and have flashed a ROM......ALL successfully.
Here's what I did:
UNLOCKING:
Unlock your bootloader by registering at HTCdev.com and following the unlock instructions. Under device, choose "All other devices", as the One S is not yet listed. It'll walk you through getting your unlock token and flashing it.
ROOTING
Follow Paul O Brien's instructions on rooting your phone. I flashed the r3 superboot file he had. The first time it didnt take and just booted the phone back up. Second time it took, and seems to have stuck, at least for apps. Please note that my phone says *TAMPERED* along with the *UNLOCKED* notification. I have no idea what that means exactly, but everything works great for me.
This means if you dont want to leave Sense but want to get the tons of useless and annoying T-Mobile and other bloatware apps out, you can. T-Mo are dicks and make almost 100% of the apps on it by default SYSTEM apps, therefore unremovable. So you'll need root and Titanium Backup to freeze or delete them. I'd recommend freezing the non-TMo one's just in case.
FLASHING ROMS
1. Flash Paul O Brien's intermin CWM touch version. You MUST use this interim CWM version for the moment, as the others do not work properly. Some things like USB mount dont work in this interim version, but the important functions like wipe and flash, backup and restore, and restart do work. The CWM recovery seems permanent, based on my initial trials, so no worries about reflashing it each restart.
2. Flash your ROM of choice from Clockworkmod Recovery. I'm using Black Dragon right now, but there are others out there as well. I'm personally looking forward to CM9, but its a little ways away, usability-wise.
So there you have it, all you US guys. Don't be afraid to mod your phone. Remember all the warranty void disclaimers as always. I'm not responsible for you bricking your phone. This is just my experience in just under 24hrs of use. Things are looking good for the One S.
bump... i see US users still asking.
Mods, can we perhaps sticky this post of mine? I don't want to take credit for the actual methods of rooting, since Paul O Brien and others deserve that credit, but I think it'd be helpful for US users, since many don't know whether or not the international method works.
That, or perhaps editing the Intl guides to make it clear that the US version accepts the same methods and ROMs.
Worked great for me
Sent from my HTC VLE_U using xda premium
So if we root and flash a custom ROM is there any way to get the phone back to factory state, and get rid of the *TAMPERED* and *UNLOCKED* notification??
Did anyone else get a bit of a sad chuckle out of the first step in the instructions being "remove and reinsert battery"?
cyberchuck9000 said:
Did anyone else get a bit of a sad chuckle out of the first step in the instructions being "remove and reinsert battery"?
Click to expand...
Click to collapse
Great, now my blisters on my fingers will heal.
But still.... I cannot imagine not needing a batt pull.
nickmv said:
Mods, can we perhaps sticky this post of mine? I don't want to take credit for the actual methods of rooting, since Paul O Brien and others deserve that credit, but I think it'd be helpful for US users, since many don't know whether or not the international method works.
That, or perhaps editing the Intl guides to make it clear that the US version accepts the same methods and ROMs.
Click to expand...
Click to collapse
+1
androidcues said:
Great, now my blisters on my fingers will heal.
But still.... I cannot imagine not needing a batt pull.
Click to expand...
Click to collapse
If you need to perform a hard reset on the One S, you hold down the power button for about 7-10 secs.
First of all, thanks for this thread...I used the HTC One S All in one tool kit to unlock my phone, unfortunately I miss understood one of the directions(#5) and stopped using the tool kit and followed another thread, much to my surprise, my bootloader is unlocked, hooray My question is, how do I get back to the original state if that is possible? The reason I ask, is I would like to go back and do it correctly...I used better terminal emulator to see if I had root, but all I got was the $ sign instead of the # sign So I would like to start over...
Thanks in advance for the help
I'm honestly not sure what the procedure is for relocking an HTC bootloader. Perhaps do some Google research on some of the latest models, and I bet you'll find something.
That being said, once you unlock the bootloader a single time, the best you can do is go to **RELOCKED** state. You'll never get back **LOCKED**. Once it's gone it's gone. I'm curious about the **TAMPERED** message though. That's an ugly word.
not sure what exactly went wrong.
somehow flashed CWM and now thats the only thing my phone will boot to, even after re-flashing the stock recovery.
can't get the phone to turn on, only CWM every single time.
suhailtheboss said:
not sure what exactly went wrong.
somehow flashed CWM and now thats the only thing my phone will boot to, even after re-flashing the stock recovery.
can't get the phone to turn on, only CWM every single time.
Click to expand...
Click to collapse
Uh oh that doesn't sound good
Sent from my HTC VLE_U using xda premium
yeah, tried reflashing both CWM & stock recovery. phone still boots to CWM everytime.
Luckily i can still access the phone via ADB, (while in recovery) so i'm sure i'll be able to sort it out. just need to take a fresh crack at it tomorrow. gonna switch back to my galaxy nexus tonight. (oh wait, i dont have any other phones that use microsim)
haha.
Hmm, interesting. Did you flash the interim recovery that Paul O Brien posted, and not another version? Just wanna make sure. I've heard of this happening in my past experience with the Nexus S, but I can't recall what the deal was. Regardless, I don't think you're in trouble. As with your GNex, it's very hard to completely brick the device unless you flash perhaps a bad hboot file, however I'm not really familiar with HTC devices.
This is my first HTC so I'm still trying to learn how the hboot and other processes work together. Sry to hear you had bad luck.
UPDATE: You should try the root install script. It tells the phone to boot after install. That might get you booted atleast.
Some thoughts:
1. Flash the stock recovery back and reflash CWM
2. Clear cache and dalvik within CWM, and make sure to use the 'Reboot System' option if you aren't already.
From what I can tell, your "boot-to-recovery" flag is set on the phone, and isn't getting cleared.
nickmv said:
So I know there's been some controversy and scares going around about the US version, since it JUST came out. I'm here to calm you guys down. I have now rooted mine, flashed an interim CWM touch version (not permanent) and have flashed a ROM......ALL successfully.
Here's what I did:
UNLOCKING:
Unlock your bootloader by registering at HTCdev.com and following the unlock instructions. Under device, choose "All other devices", as the One S is not yet listed. It'll walk you through getting your unlock token and flashing it.
ROOTING
Follow Paul O Brien's instructions on rooting your phone. I flashed the r3 superboot file he had. The first time it didnt take and just booted the phone back up. Second time it took, and seems to have stuck, at least for apps. Please note that my phone says *TAMPERED* along with the *UNLOCKED* notification. I have no idea what that means exactly, but everything works great for me.
This means if you dont want to leave Sense but want to get the tons of useless and annoying T-Mobile and other bloatware apps out, you can. T-Mo are dicks and make almost 100% of the apps on it by default SYSTEM apps, therefore unremovable. So you'll need root and Titanium Backup to freeze or delete them. I'd recommend freezing the non-TMo one's just in case.
FLASHING ROMS
1. Flash Paul O Brien's intermin CWM touch version. Some things like USB mount dont work, but the important functions like wipe and flash and restart do. The CWM recovery seems permanent, based on my initial trials, so no worries about reflashing it each restart. I cant speak for the non-interim solutions, but from what I can gather, they are problematic, so avoid them for now.
2. Flash your ROM of choice from Clockworkmod Recovery. I'm using Black Dragon right now, but there are others out there as well. I'm personally looking forward to CM9, but its a little ways away, usability-wise.
So there you have it, all you US guys. Don't be afraid to mod your phone. Remember all the warranty void disclaimers as always. I'm not responsible for you bricking your phone. This is just my experience in just under 24hrs of use. Things are looking good for the One S.
Click to expand...
Click to collapse
Is this part a must? Would you mind PM'ing me with how to do this part if it's a must? I have Unlocked and rooted my phone, just waiting for a good ROM to come by.
Thongvilay said:
Is this part a must? Would you mind PM'ing me with how to do this part if it's a must? I have Unlocked and rooted my phone, just waiting for a good ROM to come by.
Click to expand...
Click to collapse
That step is only if you want to flash ROMs, or need to wipe cache, dalvik, etc. CWM is used for flashing and recovery/backup purposes. If you're not using ROMs yet, then you have no need for it.
nickmv said:
Hmm, interesting. Did you flash the interim recovery that Paul O Brien posted, and not another version? Just wanna make sure. I've heard of this happening in my past experience with the Nexus S, but I can't recall what the deal was. Regardless, I don't think you're in trouble. As with your GNex, it's very hard to completely brick the device unless you flash perhaps a bad hboot file, however I'm not really familiar with HTC devices.
This is my first HTC so I'm still trying to learn how the hboot and other processes work together. Sry to hear you had bad luck.
UPDATE: You should try the root install script. It tells the phone to boot after install. That might get you booted atleast.
Some thoughts:
1. Flash the stock recovery back and reflash CWM
2. Clear cache and dalvik within CWM, and make sure to use the 'Reboot System' option if you aren't already.
From what I can tell, your "boot-to-recovery" flag is set on the phone, and isn't getting cleared.
Click to expand...
Click to collapse
thanks for the tips, i had tried clearing cache/dalvik within CWM and it still would not work. and yes i did flas the interim CWM from paulobrien
luckily the phone would work via ADB while in CWM. So i pushed three different ROMS to the phone, at first each oen would lock up and reboot within 20 seconds of doing anything. I then went back into recovery & wiped data/cache/dalvik maybe 10 times out of sheer frustration. Then re-flashed a fresh copy of black_dragon_v4.0, didnt do anything after boot. just let it sit there till this morning.
now the phone seems to be working perfectly...
so hopefully if anyone encounters this problem my last couple posts will help them out!
suhailtheboss said:
thanks for the tips, i had tried clearing cache/dalvik within CWM and it still would not work. and yes i did flas the interim CWM from paulobrien
luckily the phone would work via ADB while in CWM. So i pushed three different ROMS to the phone, at first each oen would lock up and reboot within 20 seconds of doing anything. I then went back into recovery & wiped data/cache/dalvik maybe 10 times out of sheer frustration. Then re-flashed a fresh copy of black_dragon_v4.0, didnt do anything after boot. just let it sit there till this morning.
now the phone seems to be working perfectly...
so hopefully if anyone encounters this problem my last couple posts will help them out!
Click to expand...
Click to collapse
Wow, I have no idea dude. That sounds kinda crazy. Hopefully all will be well in the future and you won't come across it again.
the only variable i can think of is that i did have the phone about a week before launch. HTC mailed it to me directly.
I thought maybe that had somethign to do with it, but as far as i can tell the phone was the final shipping version.
I sent you a PM, trying to find a solution.

[Q] LG Motion (Possible Cyanogen mod?)

Hey everyone! I would like to start off by saying that I am brand new here, and am surely going to mess up quiet alot... But here goes,
I've recently rooted my phone with a very simple guide, and it's the first device I've every rooted. So I know very little of the process of doing so, (I'm learning slowly).
I also have found a rom that I would like to install, but I would love to know if others think it seems legit? If it is real, I know many people would absolutely love to use it! The rom's URL is (ht tp:// playfuldroidz.com /wiki/ CyanogenMod_10_Motion) (Please remove spaces, sorry as I said i'm new...)
Now I don't mind testing this myself, but being as new as I am at android I honestly do not know how to follow the relatively simple instructions.
(This Is where I need some help, Please be noob cautious!)
Download the .zip & copy to phone or sdcard (make sure 4g or wifi is enabled if dl'd from phone).
Zip can be installed from either internal or external sd in CWM (Which ever you copied it too!)
MAKE A BACKUP!!!
DO A FACTORY RESET!!! - this will wipe data & cache!
Go to install zip from sdcard
Choose zip from sdcard
Select cm-10-xxxxxxxxxx-UNOFFICIAL-l0.zip
Confirm
Repeat Steps 5 -8 for gapps
Reboot
Now my first question I'd love some help with, is how do I perform this backup there talking about? do they just mean my simple go into settings and click backup? Or should I do it some otherway?
Second question: Do they mean the phones built in service of factory reset?
Third Question: To install a Zip from an SD card do I need to simply use ES file explorer, or root file browser? Or is there a custom way to install a Zip file on android?
Fourth and final Question: What is gapps..? Is this something I should get or use?
EDIT: I've got a fifth one also... Thanks to anyone who's stayed this long and is willing to help me.! Will this Cyanogen mod (If working) Work almost exactly like a real nexus Operating system? I've got a nexus 7 tablet running stock android, and I love it! That's why I'm doing this to my phone honestly.
Thank you all greatly!
Prophet968 said:
Hey everyone! I would like to start off by saying that I am brand new here, and am surely going to mess up quiet alot... But here goes,
I've recently rooted my phone with a very simple guide, and it's the first device I've every rooted. So I know very little of the process of doing so, (I'm learning slowly).
I also have found a rom that I would like to install, but I would love to know if others think it seems legit? If it is real, I know many people would absolutely love to use it! The rom's URL is (ht tp:// playfuldroidz.com /wiki/ CyanogenMod_10_Motion) (Please remove spaces, sorry as I said i'm new...)
Now I don't mind testing this myself, but being as new as I am at android I honestly do not know how to follow the relatively simple instructions.
(This Is where I need some help, Please be noob cautious!)
Download the .zip & copy to phone or sdcard (make sure 4g or wifi is enabled if dl'd from phone).
Zip can be installed from either internal or external sd in CWM (Which ever you copied it too!)
MAKE A BACKUP!!!
DO A FACTORY RESET!!! - this will wipe data & cache!
Go to install zip from sdcard
Choose zip from sdcard
Select cm-10-xxxxxxxxxx-UNOFFICIAL-l0.zip
Confirm
Repeat Steps 5 -8 for gapps
Reboot
Now my first question I'd love some help with, is how do I perform this backup there talking about? do they just mean my simple go into settings and click backup? Or should I do it some otherway?
Second question: Do they mean the phones built in service of factory reset?
Third Question: To install a Zip from an SD card do I need to simply use ES file explorer, or root file browser? Or is there a custom way to install a Zip file on android?
Fourth and final Question: What is gapps..? Is this something I should get or use?
EDIT: I've got a fifth one also... Thanks to anyone who's stayed this long and is willing to help me.! Will this Cyanogen mod (If working) Work almost exactly like a real nexus Operating system? I've got a nexus 7 tablet running stock android, and I love it! That's why I'm doing this to my phone honestly.
Thank you all greatly!
Click to expand...
Click to collapse
Question 1,2 and 3.. they are all done through Clockworkmod. Look through the menus you'll see it if you still struggle look on YouTube.
Question 4.. gapps is Google Apps you need to flash this after the ROM to get the play store and all the other standard Google apps.
Question 5.. in your eyes pretty much, it'll look the same but with more features obviously.
Thank you alot!
Thanks! now i've only gotta do one last thing, and see if anyone knows whether or not this website is a reliable source, or atleast if the mod works...
Prophet968 said:
Thanks! now i've only gotta do one last thing, and see if anyone knows whether or not this website is a reliable source, or atleast if the mod works...
Click to expand...
Click to collapse
Just give it a go mate, if in doubt try it out lol (don't quote me on that haha)
Alright I've got one last dumb question
CdTDroiD said:
Just give it a go mate, if in doubt try it out lol (don't quote me on that haha)
Click to expand...
Click to collapse
I was just wondering if there's a chance this clock work mod thing doesn't work on my phone? I don't really know how, or where it is either... and I'd love some help with that... Thank you!
(Edit) I don't think there is a clockwork mod for my device... According to the Rom Manager app I was told to use for installing it.
Prophet968 said:
I was just wondering if there's a chance this clock work mod thing doesn't work on my phone? I don't really know how, or where it is either... and I'd love some help with that... Thank you!
(Edit) I don't think there is a clockwork mod for my device... According to the Rom Manager app I was told to use for installing it.
Click to expand...
Click to collapse
If you did what it said in the instructions *root it, cwm, install custom rom* then after installing the custom rom it has it's own cwm. turn off the phone, turn in back home and press the back and home button together at the same time and it should take you to the rom's cwm. If the phone does a factory reset by pressing the back and home button then you did the installation wrong.
But just in case I'll setup a full instruction for you.
Root your phone.
Which can be done easily, just download this and extract the files: http://www.mediafire.com/?dhdbwflnl1vknx2
once you extract the files put your phone on debugging mode which can be done by going to settings, developer mode, and click usb debug.
once you've done that connect your phone to the pc *make sure it's on charge only* wait for driver installation to finish. once that's done click root. follow instructions on the screen it shouldn't be too hard! after following instructions you should be rooted and have cwm. but to install the recovery go to your apps and find lte 2nd init recovery and then click the top button, agree to super su to use it and you're done with rooting and cwm! now. these files you were talking about, download them and put them on sd which can be done with a file manager. after they've downloaded go to the lte 2nd init and click the bottom button. it will reboot the phone and take you to cwm. While you are in cwm click on the home button to go to external which is the sd, then go to backup and restore, and click backup! this is very important. miss this step and things could go bad. Now all you have to do is follow the instructions you posted yourself and you should be done! if you need any help don't hesitate to message me. I've done this for a long time now.
Whoops forgot to add. the website IS a reliable source. Learned that cause I'm a risk taker and decided to try it out myself. and do not use rom manager or anything like that for recovery. ever. especially on phones that do not have their own recovery mode. also. the CM10 works great in my opinion! But there's a catch. for me at least. even though everything is perfect during phone calls I cannot use my 4g. which is a bad thing for me cause I need it. other than that if that doesn't bother you or anything or don't have service then knock yourself out and install the cm10!
COMPLETED) This mod worked, all things are now finished except one small issue!
So after installing the mod with some great help of someone here on this forums, I've been basically beta testing the mod for a few days. I have nearly no complaints, as almost everything works seemlessly just like you'd except the operating system to. In the end I found one single issue though, which is terribly annoying for me in specific...
My GPS isn't working, which could be one of many things other than the rom. Seeing as I only recognized It yesterday, there may be an outside reason it at random shut off. If anyone know's what can cause this, and a fix for it please comment back!
Thanks to everyone who helped with installing the mod
Check out www.unleashedprepaids.com. have whole section on lg motion custom ROMs help guides everything u need!
Sent from my LG-MS770 using Tapatalk 4
Please help me with the rom
Hey guys not sure if i am suppose to post this here but i couldnt find any where else and i couldnt find an answer with my exact problem, i installed this rom on my moms lg motion and everything went find untill i got to gapps it came up with an error inside of cwm so i just contined all the other flashes i had to do and rebooted i thought that i could just flash gapps later. But i mad a very big booboo i installed the Recovery APK for it in cm 10 i forgot all about pressing reboot and saying reboot into revocovery so i was going to try it though the Recovery APK so i installed the thing and pressed reboot and instead of taking me into recovery it takes me to a screen that says something like "mourning call error" which i dont know what means but i had to take out the battery and turn the phone back on so that worked and i got back to the home screen but i still cant install gapps so she can use all the google sevices i tried rebooting with the built in reboot into recovery (the one that you press reboot when you hold the power button) and that does the same exact thing i have no way of flashing gapps or anything else for that matter can someone please help me i have no idea what to do. everything i working on the phone but that. thank you sorry if i put this in the wrong place.
Confused my droid using this method- would love in on this thread
Sorry if I'm posting in the wrong place-punch me if I have-
I rooted my lgms770 with version f firmware- installed cwm and 2ndinit recovery (2nd init was the only known way (to me anyway) to get into cwm at the time) followed this guide ---
[LgMotion All Things root] and
[GUIDE] Unbrick OR Unroot LG Motion 4G [KDZ] - Android Forums
I am not allowed to post urls yet...sorry...its the the first google hit
I've tried multiple versions of the official LG Firmware flash, from the website, and by following this guide-
AOKP Dirty Unicorns baseless port cm10 - Android Forums Actually, its the unicorns that got me.
With no luck there. I am running Mint16, and had to run the programs through Wine of course, then tried Q4wine, and eventually tried running though Oracle VM, and finally, I wiped my ancient dell of Linux altogether and put WinXP back on it (took 2 hours, that). No cigar. And yes, I did the drivers, all in order, etc, tried again, reinstalled etc
I finally set up adb to try to get into this droid that way, but am having problems with port permissions (I'm going to guess that's on my pc's end-running Mint16)
I can access the factory reset screen (the black and white), download mode, and the battery charges on a black screen with a nice purple font, but I am still stuck in a bootloop. I've employed all known button spamming combos to get back into cwm (there is a nandroid in there somewhere)..but alas...
Help me Obi-Wan-Kenobi's..
Peach
I had the purple letters with no way to get to the factory reset screen i just used the lg online flash tool in upgrade recovery put in the imei of the phone in made sure the phone was in usb download mode then it was fixed but for some odd reason i still cant get my phone to the factory reset option. I apologize sincerely if I wasn't detailed enough if you need any clarification on it then let me know through pm or i could even send u a link to my box folder i keep the install files in.
(Also i have a one click root app for the LGMS770 So if you or anyone would like the link i would be happy to give it to you)
Sent from my MetroPCS LG-MS770 using Tapatalk

Categories

Resources