[Q] Overheated Battery Help - Optimus One, P500, V Q&A, Help & Troubleshooting

I have just installed the Megatron Rom and the Franco Kernel on my LG P500/LG Optimus One. After installing I rebooted the device and after 5 minutes of the start up screen it said something like "Battery overheated. Automatically shutting down device for safety" . I have tried cooling the battery down and then trying again but it still says the overheat message.
Please help me with the problem.
Thanks

What cpu frequencies are you on?
Sent from my LG-P509 using xda premium

re flash kernel .
remember to wipe cache ,dalvik cache and battery stats.

The battery must have overheated because you must have set the clock speed to 806MHz. And I bet you must have enabled the option to set the clock speed on reboot too, otherwise your phone would have worked fine after you cooled it and rebooted it. So turn on your phone, immediately reduce the frequency back to the normal 600MHz, see if it still overheats. If it doesn't, slowly increase the clock speed to a max of 748 or something, that is if you feel that 600 is too laggy for you (for me its fine). Whenever you overclock your processor, never go straight for the maximum clock speed. As it is, 806 is an unstable frequency (its more than 33% higher than the normal clock speed) and will cause the phone to reboot itself, and it will greatly decrease the life of your processor. Always increase the clock speed in small increments and see if it can be handled by your phone. Never use a clock speed directly just because it works fine for something else. Even though these processors come off the same assembly line, they aren't completely identical. Also, never set the option to set clock speeds on reboot, unless you have used the clock speed for several days and is sure it will not cause any problems.
If you haven't overclocked your processor, then maybe you should try flashing the original firmware back and take it to a service center.

Gremaldin said:
The battery must have overheated because you must have set the clock speed to 806MHz. And I bet you must have enabled the option to set the clock speed on reboot too, otherwise your phone would have worked fine after you cooled it and rebooted it. So turn on your phone, immediately reduce the frequency back to the normal 600MHz, see if it still overheats. If it doesn't, slowly increase the clock speed to a max of 748 or something, that is if you feel that 600 is too laggy for you (for me its fine). Whenever you overclock your processor, never go straight for the maximum clock speed. As it is, 806 is an unstable frequency (its more than 33% higher than the normal clock speed) and will cause the phone to reboot itself, and it will greatly decrease the life of your processor. Always increase the clock speed in small increments and see if it can be handled by your phone. Never use a clock speed directly just because it works fine for something else. Even though these processors come off the same assembly line, they aren't completely identical. Also, never set the option to set clock speeds on reboot, unless you have used the clock speed for several days and is sure it will not cause any problems.
If you haven't overclocked your processor, then maybe you should try flashing the original firmware back and take it to a service center.
Click to expand...
Click to collapse
I haven't set any CPU rates because I am only up to the option where you have to enter you country, date, etc.

NanoNoodle said:
I haven't set any CPU rates because I am only up to the option where you have to enter you country, date, etc.
Click to expand...
Click to collapse
Did this problem come immediately after you flashed the new ROM? Then try to flash another one. If its a software problem, then it should solve it. If the battery still overheats while flashing or on other ROMs, then try to flash the stock firmware using KDZ. I remember reading somewhere that we can flash using KDZ without battery, but I'm not sure, so do proper research before doing that..... then take your phone to a service center

this also brings up a question ive been meaning to ask you guys, are gel cases known to heat up the phone, or trap the heat?

Gremaldin said:
Did this problem come immediately after you flashed the new ROM? Then try to flash another one. If its a software problem, then it should solve it. If the battery still overheats while flashing or on other ROMs, then try to flash the stock firmware using KDZ. I remember reading somewhere that we can flash using KDZ without battery, but I'm not sure, so do proper research before doing that..... then take your phone to a service center
Click to expand...
Click to collapse
I have switched back to the old kernel that i'm using and it's working fine.
---------- Post added at 05:51 PM ---------- Previous post was at 05:48 PM ----------
joeyxl said:
this also brings up a question ive been meaning to ask you guys, are gel cases known to heat up the phone, or trap the heat?
Click to expand...
Click to collapse
I'm using a case (I think it's gel) and it's not really trapping heat. It doesn't seem to be the problem with the overheated battery though.

allright, thanks!
Send fromy P-509 using tapatalk

NanoNoodle said:
I have switched back to the old kernel that i'm using and it's working fine.
---------- Post added at 05:51 PM ---------- Previous post was at 05:48 PM ----------
I'm using a case (I think it's gel) and it's not really trapping heat. It doesn't seem to be the problem with the overheated battery though.
Click to expand...
Click to collapse
Hey I'm a new user here. I've experienced the same problem after flashing a kernel uploaded on the website as well. I'm using an LG Optimus One as well, and as suggested, I've wiped cache ,dalvik cache and battery stats but it doesn't help at all, and I do not have another kernel on my sd card. Any suggestions guys?

dancingfins said:
Hey I'm a new user here. I've experienced the same problem after flashing a kernel uploaded on the website as well. I'm using an LG Optimus One as well, and as suggested, I've wiped cache ,dalvik cache and battery stats but it doesn't help at all, and I do not have another kernel on my sd card. Any suggestions guys?
Click to expand...
Click to collapse
Here’s the reason for anyone of you who is facing this over-heating problem with your p500 or any other p50* phone: your Kernel is NOT compatible with your ROM. Colors will likely be displayed properly, but the over-heating problem will be persistent, and will shut-down your phone as soon as it’s booted. There’s a very easy solution to this problem; however, it will involve installing another ROM which is compatible with that Kernel (or back to your original ROM). I’d suggest you do some research on the ROM you are using with that Kernel, and to get a compatible one flashed, or just to get the previous ROM installed on it again. Follow the following steps.
1. Plug-in your phone to its charger. The ‘over-heating’ sign will disappear.
2. Open your internet (if you have installed the ROM and have done a complete data-reset, just connect it to the Wi-Fi.)
3. Install your previous ROM back to get your phone back to normal and not get that ‘over-heating’ sign again. (Hopefully you know it! If not, PM and tell me.)
4. Now, if you want a different ROM installed, you’d be better off installing one that comes WITH a Kernel. Separate ROMs and Kernels are for experienced users; hence, sticking with those which come with both wouldn’t hurt until you are aware of what you’re doing and know how to handle any problems that may occur.
If you have any questions, please ask. I am extremely busy with exams, but still managed to get this post written.
Note: No CPU frequencies or anything had caused the problem.
Good luck!

Related

Security storage app? Consumes 98% battery

I have the app android booster to monitor battery use. When I go to applications everything is at 1% and 2% but the android process "security storage" is consuming 98% battery? Does anyone know what this is? Is there a way to minimize it or can I freeze it with Titanium Backup?
Sent from my SAMSUNG-SGH-I997 using XDA Premium App
I wish I knew as it's killing my battery also, I'm thinking I'll have to reflash or even odin back to stock before I'll get rd of the battery drain caused by secure storage, I found out it's com.android.providers.security that started secure storage but not much else
I see nobody is addressing this issue, or even explaining it. Too bad, as I'm having the same issue. The annoying part is, no matter what kernel I run, the same thing happens: The phone will sit sedately idle until I want to use it, then the minute I try to do something "Security Storage" starts running and the phone becomes non-responsive for 30 seconds to a minute or two while that stupid app is running.
Why can't this app do its maintenance while the phone is idle, rather than the minute the user wants to do something, or be forced into "nice" mode (don't know if Android has such a setting, but it's based on linux and linux does have such a setting) so that it's only allowed to hog the CPU when the phone is idling.
change build prop ro.securestorage to false
ElwOOd_CbGp said:
change build prop ro.securestorage to false
Click to expand...
Click to collapse
I just registered to say THANK YOU to this man. :good:
did it work?
mikim1 said:
I just registered to say THANK YOU to this man. :good:
Click to expand...
Click to collapse
I've noticed a lot of system resources get wasted even after removing the knox apps and enterprise and container agent stuff that comes on samsung phones. I mean, I guess its good as an option to have if you have use for it. Problem is tho, for ppl like me, its also built into the system in order to make those implementations effective and when you install a custom ROM and or kernel it causes errors. I think thats why some people dont like touchwiz ROMs and think theyre laggy. When the kernel and system are not synced anymore, crap goes on in the background that is just a waste. I still dont know much really, but I spent some time trying to fugure out how to disable some loggers and errors that were going on and were pissing me off. Here is a link to a post I ran across that helped shed some light on some stuff. Be careful tho, and if you don't know what your doing, spend some time to learn about what all that stuff does, because it's system stuff and you could find yourself in a bootloop or with an expensive azz brick http://forum.xda-developers.com/showthread.php?t=2599266
ElwOOd_CbGp said:
change build prop ro.securestorage to false
Click to expand...
Click to collapse
interestingly using icyfusion rom and terrasilent kernel, I cannot find this line in my build.prop. anyone else not seeing it there? secure storage is eating up at least 20% constantly of battery/cpu accord to elixir2. My battery drain continues to plague the device and I can only get about 1-2 hours of light use out of it while it continues to drain when screen is off. All I want to do is use it to listen to some tunes and I'm regretting rooting the device now. Refreshing to stock, wiping everything...formatting etc. has no effect. Has anyone solved this problem (presumably related to secure storage?) with another method?
(yp-g1 us version, currently on GB 2.3.5 stock, rooted with terrasilent kernel).
klemmaniac said:
interestingly using icyfusion rom and terrasilent kernel, I cannot find this line in my build.prop..... currently on GB 2.3.5 stock, rooted with terrasilent kernel).
Click to expand...
Click to collapse
have you tried any current builds?
ElwOOd_CbGp said:
have you tried any current builds?
Click to expand...
Click to collapse
I tried CM11 which worked fine for a week or so and then all of the sudden the battery drain problem appeared. I didn't check the build.prop when on that because I decided to reflash to stock and start from scratch trying different roms/kernels. I can't shake the battery drain now no matter what I do - factory reset full wipe, you name it. I guess I could try installing cm11 again and see if it is in the build.prop then?? I just don't know how to proceed at this point.
My suggestion would be to go into developer options and take a look at process stats to see if there are any rogue processes running that you don't need. You can also download and install BetterBatteryStats app from here on XDA or purchase the paid version from the play store so that you can specifically pinpoint what is causing your device problems. Also, older devices often need batteries replaced because they wear out. I don't think the secure storage bug affects AOSP based ROMs since it is related to Samsung's Knox. Another tip would be to use a build prop editor app that has a search function to make finding things easier.
ElwOOd_CbGp said:
My suggestion would be to go into developer options and take a look at process stats to see if there are any rogue processes running that you don't need. You can also download and install BetterBatteryStats app from here on XDA or purchase the paid version from the play store so that you can specifically pinpoint what is causing your device problems. Also, older devices often need batteries replaced because they wear out. I don't think the secure storage bug affects AOSP based ROMs since it is related to Samsung's Knox. Another tip would be to use a build prop editor app that has a search function to make finding things easier.
Click to expand...
Click to collapse
thanks for the suggestions, but it's all similar to what I've already tried. I did use Elixir2 and another battery status app to monitor things, and I have also gone through running process and disabled everything that I don't need. I did order a new battery just to check, but I don't think that's the problem. The top part of the case (where the CPU is running I presume, not the battery) is getting very hot, so there is some problem with a program or service overheating the CPU which in turn drains the battery. I just charged to full today and turned the screen off so that the device will sleep. 2 hours later, it is dead. I checked battery stats in settings and there is no indication that the device wakes while screen is off...I'm just totally at a loss. It's almost like it's a hardware issue maybe caused by a kernel or something like that, rather than an app or service. I just have no idea. Someone in another forum advised me to flash to stock and run a logcat app and post results..so I guess I'll do that. I'm worried though, because I was googling prices for ipod touches earlier today....I don't want to go back to the dark side...but I just want a device that works and I can listen to music for more than 30 minutes too.
klemmaniac said:
thanks for the suggestions, but it's all similar to what I've already tried. I did use Elixir2 and another battery status app to monitor things, and I have also gone through running process and disabled everything that I don't need. I did order a new battery just to check, but I don't think that's the problem. The top part of the case (where the CPU is running I presume, not the battery) is getting very hot, so there is some problem with a program or service overheating the CPU which in turn drains the battery. I just charged to full today and turned the screen off so that the device will sleep. 2 hours later, it is dead. I checked battery stats in settings and there is no indication that the device wakes while screen is off...I'm just totally at a loss. It's almost like it's a hardware issue maybe caused by a kernel or something like that, rather than an app or service. I just have no idea. Someone in another forum advised me to flash to stock and run a logcat app and post results..so I guess I'll do that. I'm worried though, because I was googling prices for ipod touches earlier today....I don't want to go back to the dark side...but I just want a device that works and I can listen to music for more than 30 minutes too.
Click to expand...
Click to collapse
turn gps off
ElwOOd_CbGp said:
turn gps off
Click to expand...
Click to collapse
thanks, but that was one of the first things I turned off. I only want to use the device for music listening and quick browsing/email. I shut off wifi when not using and leave it in airplane mode as well....definitely something internally wrong with the device somewhere that goes beyong changing the usual battery draining settings. Still have the logcat running and the device is making very strange noises I've never heard before...popping, screeching scratchy sounds....very strange...things just seem to be getting worse and I'm worried I'm quickly heading to an expensive paper weight situation... Battery continues to drain at 20% or more/hour with screen off. I think after this if no progress is made,...I may try to unroot the device, but I don't know if that will solve the problem and will undo the damage already done.

[Q] Performance: k3g_wq, what is it?

My Charge has seen decreasing performance. I'm running 2.3.6, the last TBH leak, and I was initially getting Quadrant scores as high as the 1400's. Now, I'm down around 700! Needless to say, the phone has gotten laggy.
I'm using OSMonitor to look at what processes are busy, and I keep seeing k3g_wq running, using anywhere from 20% to just under 40%. Never used to see it before. I figure it's a system process, as if I kill it, it starts back right away and always has the PID of 54.
I've searched here and with Google and I can't find anything about what this process is. From the name, I might guess it has something to do with 3g access, but it's running like that even when I go into airplane mode.
Thanks for any info.
just a suggestion but since GB has officially been released i would wipe cashe,dalvik and data. Then flash infinity, tweak stock or danalo's stock debloated/deoxided rom. Then flash imoseyon's repacked voodoo kernel. you will get a quadrant score of around 2000. Im currently running infinity ext4 without tsm, imoseyon's kernel and v6 script. its been pretty good for me so far. i have no complaints.
But if anybody else has a better setup. I myself would like to know as well
Wow, that's quite a prescription! For now, I'd just like to know what that process is and why it's running, so I can try to get it to back down.
Thanks for the tips. BTW, I was running voodoo lagfix back in the day, and it got me quadrant scores similar to what I was getting with this GB ROM (not 2K, but 1600 wasn't unusual); I'd like to get back to that point. Without necessarily starting over.
You're basically going to have to. The TBH leak is really old.
Sent from my SCH-I510 using xda premium
The TBH leak isn't that old (I downloaded it on Nov 7th), and the age of it doesn't make kernel processes run away. It's GB 2.3.6, basically the same as the latest OTA. And it only started doing this recently.
I'm afraid either something I've installed recently is triggering this (the better option, as I can start uninstalling stuff until the problem goes away), or there is something gone wonky with the hardware itself that the kernel is reacting to (obviously the worst case). That wouldn't surprise me, as this is my 3rd Charge, the first two having had lost their minds, running really hot and then rebooting every few minutes (this on the stock OS, rooted with the voodoo lagfix kernel).
More data (if there's anyone out there who actually knows what that kernel process is): OS Monitor's "messages" list is flooded with this:
"k3g_work_func: fifo entries are less than we want"
I get dozens of these PER SECOND.
Again, if anyone has any insight on what that process is about, glad to hear from you. Those who say "Nuke and pave!", not so much.
Fifo is an io scheduler if I remember correctly. Try changing it and seeing what happens.
"Nuke and pave" still seems like the best option.
Sent from my SCH-I510 using xda premium
kvswim said:
Fifo is an io scheduler if I remember correctly. Try changing it and seeing what happens.
Click to expand...
Click to collapse
Fifo is a general term for a queue -- "first in/first out". Many kernel processes live their lives managing queues. This one is complaining about it's queue being shorter (fewer entries) than it thinks it should have.
Did I see your name attached to a thread about trying to compile a kernel? If so, would you do me a favor, so I don't have to get all into git so I can get to the AOSP code, and grep for "k3g" and/or "k3g_wq" (still sounds to me like like "kernel 3g worker queue") and see if you can see what it does? Nothing in depth, just in general what it handles.
kvswim said:
"Nuke and pave" still seems like the best option.
Click to expand...
Click to collapse
Funny thing happened today. It was getting worse and worse. Battery stats showed a shocking thing--for the first time ever, Display wasn't the biggest battery hog, it was Android OS!
So I decided to just reboot, to see if I could get it back to good enough to do backups and start the nuke-n-pave process. I had rebooted a few times over the last few days, and it didn't solve anything. Today it did! Back to normal, and I ran Quadrant twice and got a 16xx on the second run. Nice. A few hours later, and it's still good. Keeping my fingers crossed.
Oh, I had also uninstalled DropBox (which I wasn't using yet anyway) and this massive Gameloft game, "Tintin". Those didn't help, before reboot. But maybe those, coupled with the reboot, did.
I may still nuke and pave, but probably with the stock GB and just root after that. And keep hoping the CyanogenMod comes out with a ROM for it.
Thanks.
I'm gonna revive this thread because I have a similar problem. My dad's charge is fully stock. He has never messed with anything. It was fine the whole time he had it except today. He has not used it at all today (10m screen time in 12 hours, and half of that was me trying to fix it) and the battery drained down to 30% all by itself. Me being the tech guy, he gave it to me and I checked battery usage. Android OS was reported to be using 89%. Cell standby was at 3%, and display came in last at 2%.
Since "Android OS" is very generic, I used adb to put the xda version of betterbatterystats on his phone, and under process, there is this thing called "k3g_wq" with almost a full bar. Under other, it shows the phone being awake 98.2% of the time. This problem only arose today. As he has not used the phone at all, there would be no rogue apps unless something just turned up. I disabled automatic updates in the market since the stock tunewiki app updated its permissions to read SMS (spyware???).
Does anyone have a solution to this besides factory reset?
K3G is a sensor, specifically the level sensor. Not sure why it would take up system resources, but I would think turning off auto screen rotation may be one method to try and limit its use and battery drain.
See my posts on k3g_wq above. Note that I found error log message about it not having enough entries--thus my supposition that wq == worker queue. If imnuts says it's a level sensor, then that's got to be it; from the name, I figured k was for kernel and 3g was...well...3g.
In my case, I was able to see it using OS Monitor (free in the market), using consistently about 30% of the CPU, which resulted in the OS being the largest consumer of battery.
And, for me, it finally just stopped doing it, after one more reboot. Hasn't come back. But every time the phone gets a bit laggy, I go look at that process list.
On another note, we're using my Charge at work as a test phone for our Android app, as it makes it blow up like no other device we have.
I have noticed a sensor leak associated with google maps. Try opening maps in that phone, exit out of it and see if sensor usage persists. I hadn't mentioned it before assuming it was unique to my device.
Sent from my SCH-I510 using Tapatalk
I also notice runaway usage of k3g_wq in the last week. I have stock OTA EP4 and it had been running fine for many weeks with no issue. So there has to be something that changed recently. My guesses are the new version of Google Maps, or new version of Tiny Flashlight with the "shake on lockscreen" feature. I don't see Tiny Flashlight running any services, but since I disabled the shake on lockscreen feature my k3g_wq usage seems to be OK.
I factory reset the phone and the problem disappeared.
Sent from my pocket-sized, Linux-based computer using electromagnetic radiation.
Ooooh, I just had the k3g_wq high usage issue while actively using my phone. OS Monitor showed it using 40% of processor all the time. So I tried the following:
1) disable auto-rotation. No impact.
2) started and exited maps. No impact.
3) Unistalled maps update and tiny flashlight. No impact.
3) Turned off wifi, GPS, data, BT. No impact.
4) Killed every running service that would stay killed. No impact.
5) Rebooted. This fixed it for now.
This makes me think back to the flash destroying early leak of GB for the Fascinate. This ROM would also have a similar process that got stuck using lots of CPU. On that dirty ROM, auto rotation needed to be enabled to see the issue. However once you had the problem, it wouldn't go away until reboot. The only safe thing was to disable auto rotation, reboot, and never reenable. Perhaps the Charge is now the same.
My opinion of Android and Samsung is not improving. In fact I do have some anger issues.
Give me a freaking iPhone at this point, I'll do anything for a quality engineered and tested device that actually works out of the box. Android and Google are sloppy if nothing else. Open sloppy mind you.
Scrappy1 said:
Ooooh, I just had the k3g_wq high usage issue while actively using my phone. OS Monitor showed it using 40% of processor all the time. So I tried the following:
1) disable auto-rotation. No impact.
2) started and exited maps. No impact.
3) Unistalled maps update and tiny flashlight. No impact.
3) Turned off wifi, GPS, data, BT. No impact.
4) Killed every running service that would stay killed. No impact.
5) Rebooted. This fixed it for now.
This makes me think back to the flash destroying early leak of GB for the Fascinate. This ROM would also have a similar process that got stuck using lots of CPU. On that dirty ROM, auto rotation needed to be enabled to see the issue. However once you had the problem, it wouldn't go away until reboot. The only safe thing was to disable auto rotation, reboot, and never reenable. Perhaps the Charge is now the same.
My opinion of Android and Samsung is not improving. In fact I do have some anger issues.
Give me a freaking iPhone at this point, I'll do anything for a quality engineered and tested device that actually works out of the box. Android and Google are sloppy if nothing else. Open sloppy mind you.
Click to expand...
Click to collapse
Must resist urge to flame... Seriously though, I think it's just good practice to get used to flashing ROMs, making backups, and learning to mod your phone. I've had some curious problems that only a reflash would solve. In any case, the only thing worth a damn on the iPhone 4S is the camera. The internals are fast, but what's the point?
xdadevnube said:
Must resist urge to flame... Seriously though, I think it's just good practice to get used to flashing ROMs, making backups, and learning to mod your phone. I've had some curious problems that only a reflash would solve. In any case, the only thing worth a damn on the iPhone 4S is the camera. The internals are fast, but what's the point?
Click to expand...
Click to collapse
If you're a geek and have time to flash and mod, that's great for you. I used to be in this camp. Now I just want my phone to work without contanstaintly modifying it, babysitting process and battery life. I want a phone I could recommended to ANY friend or parent without worrying. The Charge definately isn't it.
My brief history in Android:
Samsung Fascinate: got tired of poor battery life and runaway processes.
Samsung Charge: got tired of poor battery life and runaway processed. Also, voice quality is horrendous.
Samsung Galaxy Nexus: Tons of reviews of runaway "Android OS" proccessed during idle. Voice quality is bad and outbound audio drops.
With each generation, problems weren't fixed and Google/Samsung continue their careless ways. To me its just sloppy, sloppy, execution.
Scrappy1 said:
I'll do anything for a quality engineered and tested device that actually works out of the box. Android and Google are sloppy if nothing else. Open sloppy mind you.
Click to expand...
Click to collapse
You're running a leaked, unofficial build that was part of the testing process, not the result of the testing process. If it's a software related problem (either due to a rogue app or to a bug with the leaked build), there's no one to blame but yourself for installing it. If it's a hardware related issue on the other hand, there's probably warranty coverage that would cover the problem.
Go back to stock, OTA, unrooted. See if the problem persists. Reinstall your apps. See if the problem persists. If it does, your phone will be "stock" and you can pursue a warranty claim.
charlie_c said:
You're running a leaked, unofficial build that was part of the testing process, not the result of the testing process. If it's a software related problem (either due to a rogue app or to a bug with the leaked build), there's no one to blame but yourself for installing it. If it's a hardware related issue on the other hand, there's probably warranty coverage that would cover the problem.
Go back to stock, OTA, unrooted. See if the problem persists. Reinstall your apps. See if the problem persists. If it does, your phone will be "stock" and you can pursue a warranty claim.
Click to expand...
Click to collapse
No man, i already mentioned, I'm stock OTA EP4. I'm also unrooted.
Scrappy1 said:
No man, i already mentioned, I'm stock OTA EP4. I'm also unrooted.
Click to expand...
Click to collapse
Sorry, thought you were OP
Sent from my SCH-I510 using Tapatalk
k3g_wq ... it came back, and then I killed it, I think
OP here.
Today I was looking at my Charge and marveling at how I was getting pretty good performance but better battery life due to my latest tweaks in SetCPU, when I looked at battery usage: Android OS was creeping up on Display as juice-user No. 1.
Uh oh.
So back to OS Monitor, and sure enough, there's k3g_wq on a steady 25-30% of the CPU.
Opened and closed Maps--no luck.
Killed its process in the process list in OS Monitor (it appeared to be swapped out, but what the heck)--no luck.
Opened another cool app called Elixir that shows you sensors, and lets you enable/disable them. Hrm...gyroscope, rotation and orientation sensors. All were off; turned each on, then back off.
Looked in OS Monitor and...YES! k3g_wq is gone!
Wild guess time, but apparently the start-up/shut-down of whichever sensor it is doesn't always work right, and leaves that service looking for its momma (that's a highly technical description of the problem, sniff).
Anyway, if you're seeing k3g_wq running wild, give that a try. Next time I do, I'll try them one at a time, see which one does the trick (assuming it's only one).
LDog
PS -- Kudos again to imnuts for letting us know it's the level sensor. Or sensors.

[Q] Phone Shuts Down If I Smack It Really Hard and Undervolting Settings (SOLVED)

Well, so lately I would be using my phone and sometimes when I don't pay attention to it and try to turn it on, I find out that it's somehow off. I turn it back on, and it'll be fine for the day or will be randomly shutting again. At first, I had no idea to the reason why this would occur save maybe my under-volting settings, which I still believe is the case but because I tried switching to the default settings to make sure that wasn't the case, I got back to square one.
I have Octane v3.0, bhundven's 3.1 beta kernel, and thomas.raines' compilation of tweaks Lightning Zap v3.4.2.
My undevolting settings are
level0 - 1000 - 1155 - 1065
level1 - 800 - 1040 - 1035
level2 - 400 - 955 - 960
level3 - 200 - 835 - 950
level4 - 100 - 825 - 930
These values being ones I used from dsexton's guide on undervolting, but that was for Froyo I believe, or at the time, the leaked gingerbread stuff.
So I guess my questions would be what are some settings I could use to UV and not have my phone crash.
note: I just checked the forum for the kernel and the problem might be due to the latest kernel so I might go back to v3 if that'll help.
I'll try and upload a logcat if that'll help...
EDIT: Urgh, I just realized after trying to look up for more stuff related to overclocking and undervolting that the problem is most likely due to the fact that our kernel doesn't actually support overclocking yet and I had wrongly assumed that undervolting and overclocking were different enough aspects of the same thing that despite having no overclocking kernel, undervolting would just naturally be fine... Or that's what I think I've learned from all this.
If the mods can or want to, they can delete this thread, because this was an offhandedly simple question I shouldn't have asked....
Funny how you solved it before anyone answered haha. But I'm glad you fixed it!
Sent from my Rockin' Galaxy S 4G!
If you are using octane 3 and lightning zap, that might be your problem as there could be conflicts since raver put the tweaks right unit the ROM... well, that was the case with lightning zap v1... Plus, I noticed
an issue with v3.4.2 and have issued another update... But that was Bluetooth related... Try removing the init.d folder and replace the build.prop with the original, reboot and test...
Sent from my SGH-T959V using XDA App
I'll be trying that out when I have the time. Luckily it doesn't happen to often, usually when I just completely forget about my phone.
From my tank of a Galaxy S 4G. Seen more floor than a rookie lightweight in wrestling.
I had a problem similar to yours except it randomly turned off when it was in deep idle and reception was low had nothing to do with OC/UV. What i did was I went back to krylons froyo then jumped back to gingerbread or you can just use the one click heimdall to wipe everything and donit restore from any back up and see what happens.
Try putting thick business card or two business cards trimmed to battery size in the battery compartment between the battery and the back cover.Make sure its closed tightly this way when you feel the need hit your phone the battery won't go loose in the compartment, this will also work for dropping the phone on the table.
Vicious89 said:
I had a problem similar to yours except it randomly turned off when it was in deep idle and reception was low had nothing to do with OC/UV. What i did was I went back to krylons froyo then jumped back to gingerbread or you can just use the one click heimdall to wipe everything and donit restore from any back up and see what happens.
Try putting thick business card or two business cards trimmed to battery size in the battery compartment between the battery and the back cover.Make sure its closed tightly this way when you feel the need hit your phone the battery won't go loose in the compartment, this will also work for dropping the phone on the table.
Click to expand...
Click to collapse
Luckily so far I'm not having the force closes, but should I get one in the new week, I'll take these ideas to heart. The padding the area between the case and the battery I might use anyways, that's a nice idea to use.

[Q] phone almost melted

Ok so I woke up this morning (last thing I did was watch a movie while charging it) and I grabbed my phone and It literally burned me, like it came out of an oven that was 400 degrees Fahrenheit (ive had regular overheats in the past with other rom's and kernels, this was 20x worse) so I did a battery pull to possibly prevent my cpu from melting. Guessing by my battery usage in (in settings) it went from completly normal to down to 50% and blazing hot in one hour. Thankfully is is somehow still working, I am currently running hampsterblade's non-oc/uv on erikmm's miUI rc-0.2.0 LZ fixed ringer. I was just wondering if anyone else had this problem and if there was a way to prevent this from happening again, besides freezing it in dry ice lol!
Lol never! Plus all but the alpha's r more stable and faster than stock gb lol.
Sent from my SGH-T959V using XDA
Not to be a ****, but I am glad you have this problem...lol
Shoot over to this post and follow the OP:
System Cleaner
Try this method of the Gremlin Remover. I too have encounter a similar issue after multiple flashes and whatnots that we do for testing various things. This method of GR may delete data and you may have to reinstall your ROM and or kernel. Make sure you do a backup of your data using Titanium or something alike. I have also found, when reinstalling a ROM after performing the System Cleaner, you CAN do it a backup/restore of your data via the installer without any adverse affects.
Please report back with your findings and results.

[Q] Should I consider a custom ROM yet?

So I'm looking over the current options and right now it's not really looking like it's promising. I have my Galaxy S3 rooted and with the help of tools like TitantiumBackup I've managed to clean up the stock ROM pretty well. Another thing of note is I actually get some surprisingly good sound quality out of my SGS3. I realize the US models aren't supposed to have the Wolfson DAC, but somehow mine sounds absolutely incredible with no noise that I can hear or anything (it's enough that I've been wondering if Samsung might have slipped the Wolfson into this one and perhaps there is variance in the DACs actually being used.) It even drives my headphones (modified HD555s -- basically you can consider them to be like the HD595s since of course I did the foam mod, but with the soundstage mod and a custom cable they're actually a bit better possibly) extremely well. It's worth noting that I have frozen the built in equalizer or whatever it was that I thought seemed like it was meant to mess with the sound (I like my devices to produce a relatively neutral sound.) Despite some complaints out there, I actually like the sound out from my US model SGS3 better than things like my Cowon D2 (which, btw, has a Wolfson DAC) and don't even use my CMoy (which has an AD8620 OPAMP that makes it sound far better than a typical OPA2132 CMoy IMO at only the cost of a bit of battery life) which I love the sound of because to me it sounds amazing on its own.
I only mention all of this because while I'm not a true audiophile per se, quality is of extreme importance to me all the same and I'm reading of issues with sound in the current custom ROMs which is not something I'm ok with. I want it to continue to sound this amazing. The idea of losing sound quality with a custom ROM bothers me. I like the idea of a few of the updates like Project Butter (though it's worth noting that mine does run fairly smoothly since I keep the number of programs running all the time as minimal as I can) and I really like the idea of having a custom ROM where I could maybe tweak more things (perhaps including better battery life options like maybe a better CPU governor built in? It drives me crazy how much my phone can run down over just a few hours while the screen is off even with SetCPU set to set the CPU to 384MHz and switch to the powersave governer with WiFi and mobile data both disabled and me not receiving any calls or texts.) For that matter, even while on it's not helping as much as it seems like it should, but I can't help but to notice that there are some more advanced CPU governors that I don't seem to have as an option and I wonder if perhaps a custom ROM could even help there as well. Plus I just plain like being able to tweak more things to my exact preferences instead and again a custom ROM helps. But, if I have to give up that sound quality that's a big problem. I think also it might be a problem to lose the camera. I don't use it a lot, but every now and then I really do kind of want to have it. Especially it would absolutely suck to lose the ability to scan QR codes or to have to do so via the front camera, but every now and then I do take some actual photos to share.
So my question is, have any of the custom ROM options out there reached that level of stability and quality to actually be worth updating and without losing those two things? The SGS3 has been out a fair while now, so it's hard for me to believe that there hasn't been a bit more progress along these lines, but I realize that it's no simple process to create a custom ROM all the same. (In fact, I only think more progress would have been made than what I've read thus far because the SGS3 is just so very popular. If it had been a less popular phone I wouldn't necessarily expect that much, but between its features, hardware, and etc, it's a pretty popular phone.) I want all the benefits of a custom ROM, but what I've read so far of them says to me that it's just not worth the trouble. Once I find one that really works I kind of want to stick to it as much as I can as I have a lot of apps installed and configured just so for my preferences. It sounds like I'm going to have to wait a good while yet though. Or have any of the custom ROMs finally "gotten there yet"?
ive been using CM10 roms for daily use and tehy do everything i need them to do without any limitations.
i suggest you make a nandroid of all your current setup and play with some custom roms. you can always revert back if you dont liek it or cant configure them match your usage. it made my S3 experience much better, btu everyone is dfferent.
---------- Post added at 08:08 PM ---------- Previous post was at 08:07 PM ----------
there are also sound mods and stuff that are accessible with ROMs. ive never tried them but some people swear by them
You don't have any sound issues of any kind? Does the rear camera work perfectly?
BTW, I don't want any sound mod that actually changes the sound. I want it to basically leave the sound alone and produce it as well as it can without modification. None of that Beats or whatever like some do (I think that was what HTC was pushing?)
beats is a sound thing, yeah. it hink its just an equalizer though. i have used audio through headphone jack and over bluetooth to my headphones and the quality is fine for me. im not an audiophile though. it all kinda sounds the same to me lol
the only sound issues i have with my ROM are after flash some sounds do not function until you slide the volume slider from 100 to 0 then to 100 again. Its these types of quirks that come with custom rom sometimes.
my camera is working perfectly. its not as good as the touchwiz one however.
edit: heres a sound mod that might/might not interest you
http://forum.xda-developers.com/showthread.php?t=1883262
long as you do a nandroid you can always revvert back to your preferred current setup. you should also backup your IMEI
There are roms that are optimized stock. Maybe CleanRom. Don't think he adds sound mods but may be wrong. You may have used app to underclock CPU and it shows UC but probably not actually working on stock kernel as clocking must be enabled on kernel. Know this is true with overclocking.
I actually prefer to avoid all sound modifications whatsoever. Even equalizer. I like the results of a relatively neutral sound being fed to these headphones, it comes out just perfect for me. That's part of what I was worried about as some of the custom ROMs sometimes try to have stuff like that built in (and I guess that equalizer or whatever it was was Samsung or Verizon kind of doing that in the stock ROM even.)
About the camera, I actually have a commercial camera app anyway. If the only problem people have been having was the built-in app, that's a non-issue.
What's this about sounds not working until you go to zero and back though? Does this interfere with anything such as receiving phone calls (eg does it sometimes not ring because the sound isn't playing?)
BTW, where do I actually find the "official" CM10 for this phone?
no the sound works all the time after the adjustment. it takes 2 secodns to do. open volume, slide them all to 100, then all to 0, then all to 100 again.
http://get.cm/?device=d2vzw&type=snapshot
i think that these M builds are the monthyl most stable ones.
Personally I'm waiting for something built on the official VZW JB release. And yes I know I have months to wait... :-\
Sent from my SCH-I535 using xda app-developers app
There is no DAC from Wolfson but yes it sounds kick ass! Qualcom is a beast! There S4 chip is there pride and joy so they didn't want to lag behind when it comes to quality audio! God does it sound so much better then my galaxy nexus. Qualcom is making the best arm chips right now. Can't wait to see how insane the 4 core S4 is!
I COMPLETELY AGREE WITH MY FELLOW MEMBERS WHEN IT COMES TO AVOIDING ALL THOSE STUPID AUDIO MODS LIKE BEATS AND SOME OTHERS OUT THERE. THEY SUCK AND DISTORT THE AUDIO!
Sent from my SCH-I535 using xda premium
ddurandSGS3 said:
no the sound works all the time after the adjustment. it takes 2 secodns to do. open volume, slide them all to 100, then all to 0, then all to 100 again.
Click to expand...
Click to collapse
Ah, have I misunderstood? Do you just mean it only needs this to be done after the initial flash of the custom firmware itself? That's definitely no big deal at all...
prdog1 said:
There are roms that are optimized stock. Maybe CleanRom. Don't think he adds sound mods but may be wrong. You may have used app to underclock CPU and it shows UC but probably not actually working on stock kernel as clocking must be enabled on kernel. Know this is true with overclocking.
Click to expand...
Click to collapse
Well, I want to try to do this just once or at least no more than minor updates after this hopefully, so if I'm going to go ahead I want to go ahead and go straight to Jelly Bean.
I think SetCPU wouldn't be sold as only requiring root access to do its work if it required a custom kernel. It probably just works with the internal power management features that should be built in more or less by default.
mike216 said:
There is no DAC from Wolfson but yes it sounds kick ass! Qualcom is a beast! There S4 chip is there pride and joy so they didn't want to lag behind when it comes to quality audio! God does it sound so much better then my galaxy nexus.
Click to expand...
Click to collapse
Interesting... I do definitely wonder why some people have complained about hearing noise and such then. Perhaps a bad setting and/or that MusicFX app (finally had time to dig through the list to find out what exactly it was called and that's the one that I just assumed was probably an equalizer/effects processing thing that would modify the sound, but honestly I never had any use for it even if it's not and never bothered to try it.) I'm glad to hear that I'm not the only one who thinks that the US SGS3 actually sounds good. I was beginning to wonder if my ears were maybe just getting that bad somehow even though I'm still far pickier than everyone I personally know, lol.
Let me ask you this, is the so called "Voodoo Mod" any good at least? I was never clear on exactly what it was supposed to do for audio. I know things like Beats probably mostly rely on a bit of processing to increase bass and probably play with things like stereo separation or something, but I've never been clear on what that one was trying to do exactly other than that people claim it's actually an improvement for many devices.
Anyway, back on the topic at hand, I think I'm more or less convinced to at least go ahead and give CM10 a shot. I'll use that newer monthly build from earlier this month after clearing enough space to make a full backup. (Besides CWM's backup option I've already backed up my apps and settings using TitaniumBackup, so in a worst case scenario it shouldn't be too painful if things go wrong and I have to go all the way back to a stock image with a factory reset or something. Is that option in CWM the correct thing, or must I use something separate for a Nandroid backup?) Also, it may sound silly, but how exactly do I backup my IMEI? I was looking for that already upon digging through a large tutorial thread a while back and it seemed to require something I couldn't get to work (when I try the numbers mentioned in the dialer I don't get any hidden menus, just a dialtone. Other than that I could only find something about manually restoring it if it has been completely damaged or lost which wasn't a fun looking process.)
Nazo said:
I think SetCPU wouldn't be sold as only requiring root access to do its work if it required a custom kernel. It probably just works with the internal power management features that should be built in more or less by default.
Click to expand...
Click to collapse
It is sold that way. Depends on the manufacturer of the device. On stock HTC kernel it will lock 2nd core at max speed, kill battery life and cause heating problems. That is why I said it may not work correctly and without another app to monitor CPU you don't know what it is doing. How it works with Samsung I wouldn't know as I run custom kernels when possible and don't worry about clocking on stock kernels as they are under performing already.
Don't restore system apps with titanium backup! Only data apps (apps from the market)
CM is great good choice. I love the theme engine CM10 has and all CM10 based roms.
I'll tell you a super easy way to backup your IMEI! Need Root!
Download (terminal emulator)
Enter these commands. su (hit enter)
reboot nvbackup (hit enter)
It will reboot and create the backup on a built in backup partition on your SD card. The only way you could delete the backup is if you formated your SD. Super easy I just hope it works lol....
Sent from my SCH-I535 using xda premium
Two quick questions before I take the final plunge.
1. Is the CWM backup to external flash function sufficient, or do I need something further for a true backup? (It says "Nandroid" in one part, but otherwise I'm not sure if it's truly "Nandroid." It seems like it just backs up each individual file or something and I get the impression that Nandroid is more of an image of the firmware? If it isn't sufficient, what should I use?
EDIT: Found this tutorial. Basically that's what I've done except instead of bothering with Odin I used the EZ-Recovery app to flash CWM directly from the phone itself (along with EZ-Unlock 1.2 from here to unlock the bootloader) as per another tutorial. The other tutorial just didn't call it a "Nandroid" backup, so I wasn't sure.
2. If anything goes wrong, is there a stock ROM image I can use for the Verizon SCH-I535 with Odin? So far my searching has taken me to a site that practically has every stock ROM for the SGS3 but that one... (Or at least if it has that one I couldn't find it on there, which isn't saying much since every single region was listed separately...)
The best way to get recovery is to get the latest recovery from the man who's created them all from the very beginning.
Get rom manager and flash the latest straight from that app. You must make sure your bootloader is unlocked. If you took the latest OTA from Verizon it locked your bootloader.
As long as your unlocked and rooted you can go straight in rom manager and flash touch recovery especially for your Verizon galaxy s3.
I've been using the latest touch recovery on my D2tmo, nexus 7,galaxy nexus and Asus infinity and it's worked perfect.
Make a backup of your current rom for safety before flashing. You can create a backup and rename it to whatever you want straight from rom manager!
I personally wouldn't back up to the external. It might work fine but when it comes to backups I just go straight to the internal
Sent from my SCH-I535 using xda premium
---------- Post added at 08:33 AM ---------- Previous post was at 08:26 AM ----------
I soft bricked my phone because after taking the latest OTA it locked my bootloader! Recovered it fully from here
http://forum.xda-developers.com/showthread.php?t=1840030
I seen the take to your local Verizon store bla bla bla.
Got in download mode at 4am and recovered in 15 minutes.
I wish I had someone that knew what I now know and that's why I'm here to help my fellow members!
Sent from my SCH-I535 using xda premium
Hehe, funny thing about that. It tried to automatically update without bothering to ask. I presume because I had the FWupdate app frozen (for I guess fairly obvious reasons) it utterly failed and then complained, then demanded that I update again after a while, giving me an option to defer it. (I never did figure out how to get it to stop pestering, but I guess that's a non-issue.) So I didn't ever get a locked bootloader simply because it failed to do what it was trying to do.
Anyway, I've installed CM10 and so far so good. Well, I gave myself a good scare by forgetting to do a factory reset (*sigh* I wish I didn't have to do that, but, after all, it's a significant change going from a highly modified VZW infested ICS to a cleaner custom Jelly Bean) and it sat there stuck on the boot logo until I reread the instructions and rebooted to fix it (at least CM doesn't wipe out the CWM recovery like the stock ROM does...) I still have a LOT to do to get everything all reinstalled and reconfigured. I'm not going to be able to finish it all tonight, so won't really be able to comment about the results of the switch until tomorrow I guess. It's not helping that it's taking absolutely forever to download the Google Play package and all (and then I get to redownload a lot of the apps, though hopefully TitaniumBackup can safely restore a lot of it.)
EDIT: BTW, is it just me or do they really REALLY need to provide basic info on how to do simple tasks like the actual installation process itself, installing Google Play, and etc? I'm no stranger to googling for info, but wow what a pain to figure this all out (especially it never occurred to me that the gapps zip would have to be installed using CWM. I thought it was for the firmwares themselves only, not them and apps...)
EDIT2: Oh wow. I had no idea how much work this was really going to be! I said before that a full ROM install is something I wanted to do once. Well, I definitely want to never do this again. I'm having to fight all sorts of things. Google didn't even want to recognize my phone at first despite successfully connecting my accounts and registered apps such as, oh, I don't know, Titanium Backup Pro just for instance weren't showing up as already purchased... -.- I think I finally got it all restored and they now properly show up as owned, but I've lost hours just fighting with all of these various things...
It also seems to have serious issues with my WiFi. I haven't figured out what is going on exactly, but it seems like I'm having to turn wifi off and on a bit to get it to properly connect again -- I've put in my password so many times I'm about to go absolutely insane (unfortunately, for various reasons I'm still stuck on WEP 128-bit, so I have to type in a large hexidecimal encryption key and I'm just about ready to go postal.) Hopefully once everything is finally all setup and configured all will be well, but at the moment I've lost a pretty good bit of sleep while fighting this and barely have it up and running. I probably should have waited for an off day to do this.
Nazo said:
Hehe, funny thing about that. It tried to automatically update without bothering to ask. I presume because I had the FWupdate app frozen (for I guess fairly obvious reasons) it utterly failed and then complained, then demanded that I update again after a while, giving me an option to defer it. (I never did figure out how to get it to stop pestering, but I guess that's a non-issue.) So I didn't ever get a locked bootloader simply because it failed to do what it was trying to do.
Anyway, I've installed CM10 and so far so good. Well, I gave myself a good scare by forgetting to do a factory reset (*sigh* I wish I didn't have to do that, but, after all, it's a significant change going from a highly modified VZW infested ICS to a cleaner custom Jelly Bean) and it sat there stuck on the boot logo until I reread the instructions and rebooted to fix it (at least CM doesn't wipe out the CWM recovery like the stock ROM does...) I still have a LOT to do to get everything all reinstalled and reconfigured. I'm not going to be able to finish it all tonight, so won't really be able to comment about the results of the switch until tomorrow I guess. It's not helping that it's taking absolutely forever to download the Google Play package and all (and then I get to redownload a lot of the apps, though hopefully TitaniumBackup can safely restore a lot of it.)
EDIT: BTW, is it just me or do they really REALLY need to provide basic info on how to do simple tasks like the actual installation process itself, installing Google Play, and etc? I'm no stranger to googling for info, but wow what a pain to figure this all out (especially it never occurred to me that the gapps zip would have to be installed using CWM. I thought it was for the firmwares themselves only, not them and apps...)
EDIT2: Oh wow. I had no idea how much work this was really going to be! I said before that a full ROM install is something I wanted to do once. Well, I definitely want to never do this again. I'm having to fight all sorts of things. Google didn't even want to recognize my phone at first despite successfully connecting my accounts and registered apps such as, oh, I don't know, Titanium Backup Pro just for instance weren't showing up as already purchased... -.- I think I finally got it all restored and they now properly show up as owned, but I've lost hours just fighting with all of these various things...
It also seems to have serious issues with my WiFi. I haven't figured out what is going on exactly, but it seems like I'm having to turn wifi off and on a bit to get it to properly connect again -- I've put in my password so many times I'm about to go absolutely insane (unfortunately, for various reasons I'm still stuck on WEP 128-bit, so I have to type in a large hexidecimal encryption key and I'm just about ready to go postal.) Hopefully once everything is finally all setup and configured all will be well, but at the moment I've lost a pretty good bit of sleep while fighting this and barely have it up and running. I probably should have waited for an off day to do this.
Click to expand...
Click to collapse
Strange that you are having so many issues. First off, when I flash a new ROM I put the ROM and the latest GApps on the sdcard. Do a factory reset, clear dalvik cache, install the ROM then the GApps. As far as wifi, I didn't have a problem when I ran CM10, but maybe there is something messed up in the latest version. Are you running the nightlies or the M versions?
The M version from the link above (the 2012 10-11 one.) At first I thought the issue I was having was the one from before where it would decide that my network with the hidden SSID was out of range automatically the moment it lost connection (either me leaving the area or turning off WiFi) but I not only tried to use the hidden SSID enabler, but also even went so far as to just re-enable the SSID broadcast on the router, so it's no longer hidden. It seems like it's having troubles initializing the WiFi. Maybe I somehow managed to freeze/remove an app that did something or other along these lines (though I just can't see how given that it can work, it just has issues.) I'm having to turn it off and on once or twice to get it to finally reconnect. I guess it's not bad since I have the power widget in the notifications tray that makes this a bit easier, but that doesn't make this any more fun at all to deal with. EDIT: In fact, whereas the hidden SSID issue I ran into previously had it just show up as being out of range after it lost the connection until I "forgot" the network setting and reconfigured it again, it looks like nothing shows up at all until I turn it off and on -- but I don't have to redo the network setting, so this is definitely a completely different issue. I think actually it's like it's just not correctly enabling the wifi on startup if it was left on when I rebooted so I have to turn it off and back on to get it to truly turn it on in the first place.
And yeah, I cleared the cache and did a factory reset before installing. Well, bear in mind that it naturally was showing up as a different device and all. So some initial configuration was definitely going to be required to even get started, and I was switching from ICS to JB (and completely different sorts of ROMs besides) so some initial fight was inevitable even if CM10 were the most established and stable build ever made just going from the one to the other. Actually, one interesting feature of Titanium Backup Pro (once I finally got it to recognize that I had the Pro version in the first place) is apparently the ability to change the device ID to seem to be the same as far as installed programs and such go, so now Google Play among other things thinks this is the same exact device as before now as opposed to being a new device. It's actually weird because the "new" one doesn't even show up on Google Play's settings anymore (and Google still hasn't gotten around to fixing it such that we can remove devices, so I still have my old Archos 43 PDA listed in there for instance.) Between everything, Google now is letting me once again access my software without re-buying or relying on backups (which is especially good because a few things seem to just get stuck when I try to restore them -- it just sits there forever, not ever really installing.)
BTW, I lost all the Verizon-specific special numbers such as *86 for voicemail. Apparently CM10 doesn't bother to list them (but then as they are vendor specific I guess that's not a big surprise.) Is there any sort of list of the numbers Verizon uses out there -- maybe even including whatever special numbers that might be more specific to this phone itself (such as that hidden menu or whatever)?
EDIT: Ok, so far things are starting to come together slowly but surely. One oddity though, I noticed at the end of my work shift that, rather than the usual 10% or so of battery time lost, it seemed to have lost about 20%. I wouldn't go so far as to say it's double -- it might be more like 15% many times -- but it is very odd all the same. I thought I was seeing a bad trend along these lines last night, so went ahead and put SetCPU back on there with the profile to do powersaving and serious underclocking when the screen is off and in both cases I used the "conservative" CPU governor for the normal use with the maximum CPU speed at about 1GHz (conservative is supposed to be like ondemand with a better tendency towards power saving at the expense of taking longer to scale the CPU upwards when needed.) As this is CM10, there should be no room for doubt that the CPU is being scaled down -- in fact in the performance menu I often see the CPU at a mere 384MHz (which is my minimum setting) -- so I'm just not sure what to think just yet. The settings menu for the battery life shows mostly just basic system processes like the screen, idle, and etc being the main culprits for battery usage, so again odd since the screen is the main thing yet is off during my working hours (with the very short exception of my breaks.) I don't think the automatic brightness setting is any higher or anything either and, in fact, configured it to use generally lower settings until the maximum brightness.
Guess more tweaking and testing is needed to be sure, but it's odd all the same. If anything CM10 is running LESS all the time by way of hidden services and such (though as far as things that actually show up in the likes of Android Assistant I'm having to fight far more things including an "analog clock" that isn't even in the app list so I'm hoping is just the normal clock despite the fact that "analog clock" in normal firmwares is actually a separate extra thing.) Guess I'll still have to wait and see to some extent.
Edit2: Haha, I just read that you have to recalibrate the battery meter after flashing, so it'd probably just not being very accurate is all. I grabbed an app to help do that so hopefully this is all that was going on (and if I go by Android Assistant's voltage status I'd say that it definitely is off.)
Edit3: (Just kind of adding as I go along here.) Now that all the basics are in place and I had some time and the desire to drain the battery more quickly (as part of the recalibrate process you're supposed to drain it until it automatically shuts down) so I plugged in my headphones and started listening. So far so good. I was really hoping that one of the advantages of a custom ROM would be a more precise volume control (Google really dropped the ball on that one! Sometimes you're trying to get it just right and end up stuck between either a bit painfully too loud or annoyingly too quiet with no in-between) but other than some dissapointed wishful thinking, it seems sound-wise this release of the SGS3 CM10 is just fine. I don't really hear any bloat or distortion in the bass and in general the usual modifications that they do to the sound just aren't there (or at least if they are they are subtle enough to fool my, let's say "bronze" ears since I'm definitely at the bottom of the audiophile chain, lol.) In one thread where someone asked how the Qualcom compared to the Wolfson sound-wise someone said it was a bit tinny, but if it is it's far too subtle for me to notice (and this is bearing mind that these are headphones with a slight bass roll-off, so it does seem like I'd notice any significant loss in the lower ranges pretty quickly. In this respect I'm happy or at least satisfied that nothing has gone wrong.
Also, one way or the other the wifi issue seems to have gone away. I'm guessing it was an app I had frozen that I reenabled, but that's just a guess. It's so hard to be 100% sure with these things unless you apply a long painful scientific process every single step of the way...
I'm STILL trying to figure out a way to configure the haptic feedback level. It seems to be all on or all off with no ability to reduce strength of feedback that I've found so far.
Another word to the wise, backup your imei. Not sure if that was mentioned yet
Also, your ROM will work better after a charging cycle or two. It will initially scam for media and such I believe which maybe part if the reason you're seeing slightly higher usage at first. Also, in general you'll get slightly less battery life on aosp. I don't find much use in most battery stats though. They're easily manipulated.
Sent from my Galaxy Nexus using xda app-developers app
Well, I had a small accident. I was replacing some fonts and manually selecting which ones to replace with what when I threw in Arial Unicode and another font that was still slightly large. I'm assuming because the font files were so big, but it completely stopped booting. After fighting with it for hours upon hours (and I have since found what might be a font zip file for CWM now that it's far too late to do me any good -- though of course it would have had to replace those particular fonts and it seems like most of my attempts to replace them ended up replacing everything but them.) I just couldn't get a driver to install for the phone while CWM was running (I don't know if you can maybe get an adb shell or what, but without the driver you obviously can't.) In the end, I ended up having to reformat and reinstall CM10 from scratch. So far (knock on wood) none of the real problems I was having before have really repeated. (And this time around I just kept my font changes minor and no gigantic overkill fonts.) Sadly, TitaniumBackup can't restore all apps it seems (it just sort of freezes on some) but overall I've managed to restore most of it. I was waiting to make a backup in CWM until I had fully gotten everything configured and running the way I wanted it. Guess I should have done one sooner, but now I'm close to the original goal of having it basically right where I want it before making the backup (thank goodness TitaniumBackup at least was able to get the bulk of the work. And I love how it can even restore the device ID so that as far as everything is concerned this is the same phone I've always been using.)
It does still have a worse battery life compared to the stock ROM, but I guess it's not too bad. Still better than most phones no matter how you look at it. I'm not entirely sure it wasn't the battery being somewhat at fault though. I was using a third party battery by Anker. By the feel of it, it actually is surprisingly dense for a third party battery -- it weighs about the same amount as the stock battery -- so it might actually have a pretty good capacity, but at the same time I'm not 100% sure it truly is every bit as good. At first it certainly seemed to be, but maybe it's starting to wear down more quickly overall. For now I guess I'll switch back to stock (my original plan was to just store it at some 70% or so capacity so it should last and then punish these two third party batteries, but now I guess I'll consider them to be the backups instead. I don't like that the charge goes as high as 4.33V or so though. 4.2V is supposed to be considered pushing things pretty hard as it is, so I have a bad feeling about the overall lifetime of these batteries...) Again I have SetCPU hopefully helping out a bit (I like that CM10 has options for this that it can set on boot, but it doesn't have any other options than that and I like how I can have SetCPU actually lower things much further while the screen is off. I don't care if some processes take longer to, well, process while the screen is off after all, so there's no reason not to use a lower CPU setting IMO.) Actually, I was beginning to become quite concerned because the battery was actually going down just doing a few basic things like restoring backups while plugged into the charger despite having the governor on conservative, the maximum CPU frequency at 1066MHz, and the I/O set to SIO (which at least one person claims is better, though I wasn't 100% convinced from what little I could tell -- if anyone has any suggestions for the best balance between battery life and performance in this respect I'm curious. I try to keep it on something that kind of scales so that games and such still work fine without me having to change it specifically for each or something while it could still at least not kill the battery when it's not being pushed as hard.)
Interesting thing about the whole WiFi thing. I read on one thread where someone suggested changing the device name (in the developer options) to no longer have a dash in it to stop the intermittent WiFi dropouts. It's kind of ridiculous and should have absolutely no effect whatsoever on this, but so far it actually seems like it might have worked. Again, knock on wood... It's odd though because I never had that trouble with the stock firmware (then again, for all I know it didn't have a dash in its default device name and I doubt I ever changed it if it was even an option though I can't really remember one way or the other if I could have.) I won't know for sure for a while as it was kind of random before, but so far it's looking promising at least. And I haven't had any trouble with it picking up my network yet either.
BTW, I forgot to do the IMEI backup before somehow. Is it too late to for it to be any good now? I know, I know, but I was a bit excited about the prospect of going to CyanogenMod 10 in the first place and just forgot along the way I guess. I went ahead and ran it ("reboot nvbackup" from the terminal anyway -- it sure would be nice if it actually properly shut down first instead of doing a cold reboot -- but other than some tiny blue text in the corner that might or might not have said something to the effect of that it was making a backup it just flashed by and booted up normally. I was expecting a recovery menu or something.) But I don't know if it's going to do any good to have run it now. Is there anything other than the IMEI itself contained in that data that I should be concerned about? I think the IMEI is correct still (I checked the numbers in the settings at least and they seem to correspond to what I wrote down from under the battery) but I'm not sure about anything beyond the numbers themselves.
Nazo said:
Well, I had a small accident. I was replacing some fonts and manually selecting which ones to replace with what when I threw in Arial Unicode and another font that was still slightly large. I'm assuming because the font files were so big, but it completely stopped booting. After fighting with it for hours upon hours (and I have since found what might be a font zip file for CWM now that it's far too late to do me any good -- though of course it would have had to replace those particular fonts and it seems like most of my attempts to replace them ended up replacing everything but them.) I just couldn't get a driver to install for the phone while CWM was running (I don't know if you can maybe get an adb shell or what, but without the driver you obviously can't.) In the end, I ended up having to reformat and reinstall CM10 from scratch. So far (knock on wood) none of the real problems I was having before have really repeated. (And this time around I just kept my font changes minor and no gigantic overkill fonts.) Sadly, TitaniumBackup can't restore all apps it seems (it just sort of freezes on some) but overall I've managed to restore most of it. I was waiting to make a backup in CWM until I had fully gotten everything configured and running the way I wanted it. Guess I should have done one sooner, but now I'm close to the original goal of having it basically right where I want it before making the backup (thank goodness TitaniumBackup at least was able to get the bulk of the work. And I love how it can even restore the device ID so that as far as everything is concerned this is the same phone I've always been using.)
It does still have a worse battery life compared to the stock ROM, but I guess it's not too bad. Still better than most phones no matter how you look at it. I'm not entirely sure it wasn't the battery being somewhat at fault though. I was using a third party battery by Anker. By the feel of it, it actually is surprisingly dense for a third party battery -- it weighs about the same amount as the stock battery -- so it might actually have a pretty good capacity, but at the same time I'm not 100% sure it truly is every bit as good. At first it certainly seemed to be, but maybe it's starting to wear down more quickly overall. For now I guess I'll switch back to stock (my original plan was to just store it at some 70% or so capacity so it should last and then punish these two third party batteries, but now I guess I'll consider them to be the backups instead. I don't like that the charge goes as high as 4.33V or so though. 4.2V is supposed to be considered pushing things pretty hard as it is, so I have a bad feeling about the overall lifetime of these batteries...) Again I have SetCPU hopefully helping out a bit (I like that CM10 has options for this that it can set on boot, but it doesn't have any other options than that and I like how I can have SetCPU actually lower things much further while the screen is off. I don't care if some processes take longer to, well, process while the screen is off after all, so there's no reason not to use a lower CPU setting IMO.)
Interesting thing about the whole WiFi thing. I read on one thread where someone suggested changing the device name (in the developer options) to no longer have a dash in it to stop the intermittent WiFi dropouts. It's kind of ridiculous and should have absolutely no effect whatsoever on this, but so far it actually seems like it might have worked. Again, knock on wood... It's odd though because I never had that trouble with the stock firmware (then again, for all I know it didn't have a dash in its default device name and I doubt I ever changed it if it was even an option though I can't really remember one way or the other if I could have.) I won't know for sure for a while as it was kind of random before, but so far it's looking promising at least. And I haven't had any trouble with it picking up my network yet either.
BTW, I forgot to do the IMEI backup before somehow. Is it too late to for it to be any good now? I know, I know, but I was a bit excited about the prospect of going to CyanogenMod 10 in the first place and just forgot along the way I guess.
Click to expand...
Click to collapse
No your OK you can get your IMEI underneath where your battery is. There's a tutorial on YouTube
Sent from my SCH-I535 using xda premium

Categories

Resources