I need help! I rooted yesterday with no problems. Tonight I was into Titanium searching for a way to remove bloat. I pushed a tab by mistake. It said it would remove 45mb and reboot. The phone now starts a reboot with sound, then goes into a cycle of the Samsung name screen (no sound) then to the Android launch screen (no sound). Then it just repeats over and over...I have removed the battery and replaced and tried to reboot, with no success. What did I do???
ehogan45 said:
I need help! I rooted yesterday with no problems. Tonight I was into Titanium searching for a way to remove bloat. I pushed a tab by mistake. It said it would remove 45mb and reboot. The phone now starts a reboot with sound, then goes into a cycle of the Samsung name screen (no sound) then to the Android launch screen (no sound). Then it just repeats over and over...I have removed the battery and replaced and tried to reboot, with no success. What did I do???
Click to expand...
Click to collapse
Have u installed clockworkmod recovery?! If yes then just keeps power + volume down + menu buttons pressed and boot ur phone. This should boot into recovery ( a screen with small text) then u gotta flash a new rom. Read about recovery and flashing.
If u haven't installed recovery ur in trouble. You'll have to push it to ur phone via adb. Ur phone is now "bricked" . Ask some senior member in the exhibit forum, as different phones have different unbricking methods
Hit THANKS if I helped you
But don't worry it's not that hard and we're here to help you.
Swyped From My Ice Cream Sensation
Virtuous 3.0
Hi guys,
Really sorry to ask about this but tearing my hair out!
I have a P6200 UK model. I installed CWM v6.0.1.0 and it worked fine. The intention was to install Galaxy ROM HD (build #06), so I downloaded it, put it on my SD card, and installed from CWM recovery. The install got stuck on "Flashing boot" - so after around 15 mins I reset it.
It went into a boot loop on the initial Samsung logo. Luckily I'd previously re-flashed stock HC with Odin (to cure a dead Wifi problem caused by, I think, an errant install of Busybox) so I did this again, rebooted, and the system came up, text started scrolling up the screen, followed by a red error message (see picture) and a reboot. I was then once again stuck on the initial Samsung Tab 7.0 Plus log. I repeated the process and it didn't even get past the Samsung logo.
So I thought I'd try the newly released ICS Rom (GT-P6200_ATO_P6200XXLQ1_P6200OXALQ1) - this seemed to install OK, then half booted, did some text type installation stuff with the blue Android, then rebooted again, finally getting stuck on the Samsung logo with blue pulsating behind it. It never gets any further than that.
I tried flashing HC back - same result as earlier. I can also reflash CWM and sometimes it works, sometimes it doesn't. It seems I've run out of options.
So - question is - where (if anywhere!) can I go from here?
Help greatly appreciated, many thanks!
have you tried a system wipe in cwm? if not do a system wipe and reflash HC using odin.. same thing happen to me 2 days ago.. I think something is up with HD rom
Sorry everyone... I tried one more time (my 5th attempt!) and it worked this time! I have no idea what happened with the earlier attempts. Thanks
Hello everyone. I'm having a problem with a Rogers Skyrocket here and hope someone can help. It was running a custom ROM, but I was given the task of returning it to stock. I don't recall which ROM was on it, but it worked nicely. I should have just kept it that way!
Thanks to vincom's super helpful posts, I got the info & file(s) needed to get this thing back to stock. I installed Odin 1.85, and extracted
I727RUXLF3_I727RRWCLF3_I727RUXLF3_HOME.tar.md5
from the zip. I started by doing a wipe/factory reset (from inside the custom rom) first, and rebooted to see that it showed the initial setup screen. Then pulled battery and booted the phone into ODIN mode. I made sure to kill Kies completely before connecting the phone to my laptop (WinXP). Then launched Odin, hit the PDA button, loaded up the above file, left the check-boxes as they were, and flashed. It was successful, and rebooted the phone.
The rogers logo appears, and the samsung galaxy bootanimation comes up, and it continues to animate.... forever (for the record, I waited 20 minutes, more than enough time). I can pull the battery and try to boot again but it still stays on the bootanimation. I'm not sure what else to do? I can still get into stock recovery or Odin mode. Can anyone help? Thanks
Hi everyone!! New here, but not new to Forums in general. I searched around and couldn't find my exact issue, so I figured I’d start a new thread. This is gonna be kinda long, but I wanna give as many details as I can to keep things accurate.
My wife and I both have the Galaxy S2 T989 (T-Mobile). Both purchased like new off eBay. When I got hers a couple months ago, as soon as I got it I factory reset and wiped the caches, upgraded to JB via Kies, and then turned right around and rooted it via Odin using the instructions found on galaxys2root.com. Everything went flawless, took me less than a half an hour total for everything. I got mine a couple months later and did the exact same process as soon as I got it in the mail. However after rooting on Odin and getting the green pass just like hers, it got stuck in a boot loop when it rebooted. It would go as far as the "galaxy S2" splash screen, and sometimes past that to where the Android takes off, then reboot, or freeze. It then became unresponsive to any button pushes and I had to pull the battery to get it to shut off (The battery is a new OEM Samsung battery incidentally). I ultimately had to unroot, re-install ICS and re-upgrade back to JB via Kies again to get out of the loop. I did this whole process 3 times to make sure it wasn’t something I did. So I’m still running unrooted with JB on it now.
The only thing I noted that was kinda odd was that when I open Rom Manager in my current non rooted state, it shows that I already have CWM and TWRP installed on it. Even though when I go to recovery mode it's the standard OEM Samsung menu. I never installed TWRP, and CWM was only on it for a bit when I was in the boot loop. Could this be my issue? Are they both still somewhere on my phone interfering with each other and I can only see them via ROM manager?
Sorry for such a long first post, and thanks in advance!
addamT989 said:
Hi everyone!! New here, but not new to Forums in general. I searched around and couldn't find my exact issue, so I figured I’d start a new thread. This is gonna be kinda long, but I wanna give as many details as I can to keep things accurate.
My wife and I both have the Galaxy S2 T989 (T-Mobile). Both purchased like new off eBay. When I got hers a couple months ago, as soon as I got it I factory reset and wiped the caches, upgraded to JB via Kies, and then turned right around and rooted it via Odin using the instructions found on galaxys2root.com. Everything went flawless, took me less than a half an hour total for everything. I got mine a couple months later and did the exact same process as soon as I got it in the mail. However after rooting on Odin and getting the green pass just like hers, it got stuck in a boot loop when it rebooted. It would go as far as the "galaxy S2" splash screen, and sometimes past that to where the Android takes off, then reboot, or freeze. It then became unresponsive to any button pushes and I had to pull the battery to get it to shut off (The battery is a new OEM Samsung battery incidentally). I ultimately had to unroot, re-install ICS and re-upgrade back to JB via Kies again to get out of the loop. I did this whole process 3 times to make sure it wasn’t something I did. So I’m still running unrooted with JB on it now.
The only thing I noted that was kinda odd was that when I open Rom Manager in my current non rooted state, it shows that I already have CWM and TWRP installed on it. Even though when I go to recovery mode it's the standard OEM Samsung menu. I never installed TWRP, and CWM was only on it for a bit when I was in the boot loop. Could this be my issue? Are they both still somewhere on my phone interfering with each other and I can only see them via ROM manager?
Sorry for such a long first post, and thanks in advance!
Click to expand...
Click to collapse
Try flash a stock firmware by using flashtool, it will work 100%:angel:
revernwe therefore
addamT989 said:
Hi everyone!! New here, but not new to Forums in general. I searched around and couldn't find my exact issue, so I figured I’d start a new thread. This is gonna be kinda long, but I wanna give as many details as I can to keep things accurate.
My wife and I both have the Galaxy S2 T989 (T-Mobile). Both purchased like new off eBay. When I got hers a couple months ago, as soon as I got it I factory reset and wiped the caches, upgraded to JB via Kies, and then turned right around and rooted it via Odin using the instructions found on galaxys2root.com. Everything went flawless, took me less than a half an hour total for everything. I got mine a couple months later and did the exact same process as soon as I got it in the mail. However after rooting on Odin and getting the green pass just like hers, it got stuck in a boot loop when it rebooted. It would go as far as the "galaxy S2" splash screen, and sometimes past that to where the Android takes off, then reboot, or freeze. It then became unresponsive to any button pushes and I had to pull the battery to get it to shut off (The battery is a new OEM Samsung battery incidentally). I ultimately had to unroot, re-install ICS and re-upgrade back to JB via Kies again to get out of the loop. I did this whole process 3 times to make sure it wasn’t something I did. So I’m still running unrooted with JB on it now.
The only thing I noted that was kinda odd was that when I open Rom Manager in my current non rooted state, it shows that I already have CWM and TWRP installed on it. Even though when I go to recovery mode it's the standard OEM Samsung menu. I never installed TWRP, and CWM was only on it for a bit when I was in the boot loop. Could this be my issue? Are they both still somewhere on my phone interfering with each other and I can only see them via ROM manager?
Sorry for such a long first post, and thanks in advance!
Click to expand...
Click to collapse
hi,
can 'be that your device has some residual old. Do as you have advised. install a stock rom and firmware, so it becomes a new cell phone. After odin starts TWRP (much better) and root.
I would flash a complete bone stock Rom using Odin and start over. Also rom manager was highly discouraged on the AT&T version of the s2 so I don't know what the stance is on T-Mobile's version
Sent from my CLEAN Note ll
brandonarev said:
I would flash a complete bone stock Rom using Odin and start over. Also rom manager was highly discouraged on the AT&T version of the s2 so I don't know what the stance is on T-Mobile's version
Sent from my CLEAN Note ll
Click to expand...
Click to collapse
Thanks for the advice! Should i flash it back to ICS then try to root again via Odin before i upgrade back to JB? I'm guessing there's something that isn't getting wiped. Since i can run CWM and Root with Odin without a hitch. it's the initial reboot after all that is done that I go into the boot loop.
tainiun rioters
pierm said:
hi,
can 'be that your device has some residual old. Do as you have advised. install a stock rom and firmware, so it becomes a new cell phone. After odin starts TWRP (much better) and root.
Click to expand...
Click to collapse
Sorry for my ignorrance, what exactly is TWRP, and is it now on there because i used Odin and it installed it automaticly? And do i want to use this vice CWM?
One more question...before i try all this, can i backup everything on Kies just like i would be able to with CWM and reinstall if my root fails again? I've only used Kies for firmware upgrade, never to reinstall a backed up copy of my phone.
Thanks!
addamT989 said:
Sorry for my ignorrance, what exactly is TWRP, and is it now on there because i used Odin and it installed it automaticly? And do i want to use this vice CWM?
Click to expand...
Click to collapse
addamT989 said:
One more question...before i try all this, can i backup everything on Kies just like i would be able to with CWM and reinstall if my root fails again? I've only used Kies for firmware upgrade, never to reinstall a backed up copy of my phone.
Thanks!
Click to expand...
Click to collapse
Hi
TWRP and the 'one touch recovery, better than CWM.
The backup kies can not recover from CWM
steps:
install odin, after recovery, nandroid backup, ROM, and root.
hi
Flash the stock firmware using odin!!..it will work!
Sent from my GT-N7100 using xda premium
freezes then booted
Hello I have this problem with my galaxy s2 i9100. After reboot the phone wasn't booting something like "boot loop" so I re flashed the firmware and now the phone boots up but after the boot it freezes immediately. So I decided to install clock work mod recovery and install cyanogen mode 11 with cyanogen mode the phone boots up and are able to be used again until the screen goes to sleep mode or the power button is pressed then the screen goes black and doesn't turn on after long pressing the power button it reboots. So I don't know what else to do I have tried kernels, operating systems re flashing reseting and nothing helps. No need to tel me to do resettings. Also my galaxy s2 i9100 chip has insane chip bug but I don't know if it has to do something with my problem.
Hi there everyone, recently signed up on here as xda seems to be the holy grail when it comes to all thing smartphone.
I'm fairly new to these type of phones and recently was given an infuse 4g that was suffering a power button problem.
The power button problem has been resolved with a new one and the phone was working fine for 3 / 4 weeks.
One day the phone shut down by itself and entered the boot loop syndrome. Factory clearing it hasnt seemed to do anything to resolve the problem as it continued to reboot continuosly.
I came across the thread about gtg ultimate unbrick guide in the developers forum and this seemed like a good way to go, get the phone all the way back to stock and then work from there.
Kies installed and all drivers installed fine. downloaded the gtg unbrick pack and followed the instructions line for line. Odin reports everything passed, took about 2:59 to complete.
phone rebooted and continued to do boot loop so went into recovery as stated and wiped data and cache and rebooted again.
phone is still stuck in some sort of boot loop, but it gets to display the 1st of the setup android phone screens, then just as you get a chance to select next to go onto the next screen, the phone reboots.
Any one have any idea what could be going wrong or as im fairly new to this, is there anything im doing or not doing right that is causing this.
The phone is an at&t infuse.
regards
Trevor
sound like an issue with stuck power button. it's a know issue with this model. google "infuse 4g boot loop" there's few youtube videos you can try.
tt33333 said:
sound like an issue with stuck power button. it's a know issue with this model. google "infuse 4g boot loop" there's few youtube videos you can try.
Click to expand...
Click to collapse
I've already replaced the power button with a new one, but the technician i use did say he will remove the power button completely to see if it does the same, just to rule that out
Trev
just redone the gtg flash and it boots into the os (ver2.2.1) and then within about 5 seconds turns off and reboots
can the new on off switch be faulty......im not so sure as in recovery mode, i can leave it on that screen forever and it doesnt attempt to reboot
Tried the one click repair with hemdial or what its called, updating thisnpost via a moto defy mini so excuse any typos.. The hemdiaOl just seemed to meas it up further. So got baxk into downliad mode with odin and reflashed to gtg brick recovery. Not fixed, still booting but at least the screen is now viewable.
To recover one of these phones, is there like a definitive guide as to what to do to first prepare one of these phones for recovery, ie, first, flash to this with cwm and then clear data, cache, dalcik etc. like an idiots fuide, i feel i may need one
Regards
Trev