I am wondering what voltage the Xda car adaptor runs at?
I have a couple of Nokia car adaptors here that run at 7volts, even thought the mains adaptor runs at 5volts.
Is 7 volts going to fry my Xda II ??? :?:
I have a 3rd party combination unit. It has a USB sync-charge cable but also has a mains power adapter and a car accessory socket adapter both with a socket to accept the USB end off the sync-charge cable. So you can charge the XDA II by mains power, car, or USB port on PC.
Anyway, my point is the output voltage of the mains and car accessory socket are both 5.8v
Will 7v fry your XDA ii? I don't know but the cost of a compatible car charger or a 3rd part unit like mine is a lot less than the cost of a replacement XDA II
Ed
On my AC Adapter, it says the output is 5V and 2A.
I'd stay away from 7V, it's nearly 50% more than it wants.
Blaze_au said:
I am wondering what voltage the Xda car adaptor runs at?
I have a couple of Nokia car adaptors here that run at 7volts, even thought the mains adaptor runs at 5volts.
Is 7 volts going to fry my Xda II ??? :?:
Click to expand...
Click to collapse
I am really interetsed to know what the 12volt car adaptors run at. If someone has one can they put a meter on it and let me know.
As I said above, the nokia AC adaptors are rated at 5volt, but the car charger gives out 7volts and the nokias seem to survive ok.
I'm not keen to plug my XDA in until I get a reading on the car charger's output..
I don't have a car charger, but I can't imagine any reason why it's output would be any different than the ac charger.
if one are going to measure the volts out of an car chager then it's best to measure it while it's charging a device since volts when there are no amps being drawn are often higher then when the amps are being drawn
the right answer
the correct answer is min 4.8 - max 4.9 volts 2A :lol:
I'm thinking of buying a car charger plug with a usb connection to use with the usb cabel that comes with the diamond.
What output rating should that car charger have?
The one I'm thinking of buying has a output of 5V and 1000mA. I've seen others with 500mA but not sure which one to get?
Does anybody have any idea?
Thanks /Sonny
All up to 2A should work! The charging process with 500mA could be slower. But they will all work!
Just calculate, the original battery has 3.7V with 900mA, that makes 3.33Wh.
So the charging process is never at full capacity for optimal charging of the battery.
With an output of 5V and 500mA the charging should last about an hour or 1 1/2 hours. So I think 1000mA should be more than enough.
Couldn´t find any hint on the original output current of the HTC charger, sorry.
Thanks for the quick reply!
I will go for the 1000mA then, same price anyway
Thanks!!
Just found this in the manual
AC Adapter Voltage range/frequency: 100 - 240V AC, 50/60 Hz
DC output: 5V and 1A
/Sonny
Does the Car Charger for TOUCH CRUISE DUAL fit in the Diamond as wel?
Same connector?
It seems the only way to fast charge a N1 is with the supplied wall charger. Standard Micro USB chargers whould only allow at much as 450mA of charge current regardless of the adapter current capacity.
The bundled charger however, manages to push 900mA into the N1. I made a cut in the charger wires and measured the current draw to make sure.
Now.. I'd like my car charger to be able to do the same. There must be some hack in the plug of the N1 charger since there are only 2 conductors from the case to the plug. You can see that the plug is somewhat longer than similar Micro USB plugs..
So I tried to see if one of the 3 unused pins can tell me anything but.. they seem unconnected as far as I could tell. Diode measurement (to test for any digital part inside) also did not produce any results. The next obvious step is to take the molded plug apart but I'd rather not...
Does anyone have any clue as to what makes that plug so special?
And please - I did my tests with a bench power supply - not the car chargers - so don't go around telling me it has to do with charger current capacity.
Thanks,
Nir
are you sure the micro usb cords you are using are able to handle the amps? most chargers made prior to now, only push about 450mA, the G1, and N1 chargers i have push a full amp though. I just ordered a car charger that pushes an amp too. There is nothing "special" about the plug.
followinginsanity said:
are you sure the micro usb cords you are using are able to handle the amps? most chargers made prior to now, only push about 450mA, the G1, and N1 chargers i have push a full amp though. I just ordered a car charger that pushes an amp too. There is nothing "special" about the plug.
Click to expand...
Click to collapse
I beg to differ. All the cords can easily supply 1 AMP. It is the phone itself that decides how much to draw from the charger based on something IN THE PLUG.
I am an electronics engineer so do understand I know perfectly what I am talking about
And your 1A car charger does not supply anything over 0.45A to the phone.. you will see that if you are using the phone while it charges (say nav or phone call) the phone actually looses some charge albeit it being charged... This will not happen with the stock wall charger.
I have a 900mAh car charger that I use and it does in fact give 900mAh to the phone while charging. I can tell because I used a 450mAh charger at home before and it was slooow and I could drain my phone while charging it. With the car charger I can stream music with spotify, use the GPS, have the screen on full brightness and the battery % will still go up.
I also bought a new wall charger recently, which is 850mAh on the USB port and has a 350mAh charger for a loose battery as well, works quite nice.
Has anyone measured the voltage or put a scope on the output of the stock charger?
maybe stock charger has a slight variance in voltage over USB chargers or some signalling going on and this tells the N1 to take more current from it?
I would like a solution to this too I've seen my phone discharge while on a supposedly 1A car charger using co-pilot.
SBS_ said:
I have a 900mAh car charger that I use and it does in fact give 900mAh to the phone while charging. I can tell because I used a 450mAh charger at home before and it was slooow and I could drain my phone while charging it. With the car charger I can stream music with spotify, use the GPS, have the screen on full brightness and the battery % will still go up.
I also bought a new wall charger recently, which is 850mAh on the USB port and has a 350mAh charger for a loose battery as well, works quite nice.
Click to expand...
Click to collapse
Forget the numbers on the chargers - what counts is what really goes into the phone and that needs to be measured with a current meter (test equipment). What you may think to be fast might not be that.
Original HTC chargers obviously do the trick of fast charging but this comes at a price compared to the $3-$4 garden variety on Ebay and the likes.
now I cannot help you with the electronics at all, but, my old HTC Touch Pro charger seems to charge the same as the one which came with the phone, is this correct?
(suits me if it is, as then I have a charger for home and work)
my blackberry bold 2 charger only says it outputs 700MAh, but both the google and htc chargers both say 1.0A
dnts said:
Forget the numbers on the chargers - what counts is what really goes into the phone and that needs to be measured with a current meter (test equipment). What you may think to be fast might not be that.
Original HTC chargers obviously do the trick of fast charging but this comes at a price compared to the $3-$4 garden variety on Ebay and the likes.
Click to expand...
Click to collapse
Yes, it is just anecdotal evidence as I don't have any equipment to measure it. But my phone no longer discharges when I use it while charging, which it used to do with the old charger I used. So while I can say for a fact that the charger I use now is faster, I can't say by how much (this goes for both the car charger and the one I put in the wall socket).
I ordered this charger a few weeks ago and it charges my phone as fast as the original charger. The label says 5v / 1200mA.
Genuine Nokia Mini AC-10U US Type AC Charger (100~240V)
$7,25 and free shipping. (Takes a while before you get it tho.)
GazzaK said:
now I cannot help you with the electronics at all, but, my old HTC Touch Pro charger seems to charge the same as the one which came with the phone, is this correct?
Click to expand...
Click to collapse
HTC Touch Pro = mini USB
Nexus One = micro USB
Not an engineering here, but I am guessing the phone not always drawing more than 500ma may be is to do with the charger itself.
There is this "fast charge" USB standard where a wall plug has the USB data pins shorted to indicate that it is a wall plug and hence the phone knows when to draw more power. So even if the charger is rated 1A, the phone might not know if it could utilize that if those pins aren't shorted. Try doing a quick Google on this ....
If someone can test if the stock charger that came with the phone in fact does have those pins shorted that would confirm part of this theory.
For all practical purpose - I used two cables/plugs with a bench adjustable power supply. Simple micro USB plug would only let me draw 450mA regardless of power supply voltage in the range 4.5-5.5V. Tried shorting data pins - nothing. Tried shorting spare pin to VCC or GND or any of the other pins - nothing.
Used original cable and plug - draws 900mA at voltages from 4.9-5.5.
So it's in the plug somehow.
Tried (very difficult) to see if the pins on the plug are shorted and all 3 spares (except for 5V and GND) seems unconnected.
Next step is the irreversible hot knife...
I'm bugged by this, too. I tested with my desktop dock connected to my car charger (which states 1000 mA): it loads slowly and my battery widget reports USB- instead of AC-charger.
Might it be that the phone tries to load more than 1000 mA at the beginning to be sure that it doesn't overload the charger? And if that fails, it falls back to 500 mA?
Could N1 use a simple logic of:
- always watch the voltage
- start drawing 500ma (or whichever is the lowest current as per USB spec)
- increment in say 50ma steps
- if voltage drops below 4.x V, back off and stay at that level
I just did a little test of my own. I have a Palm Pre car charger (actual Palm brand one labeled as 1000ma output) and I plunged my N1 into it on my way home from work. In twenty eight minutes, my battery went from 47% to 70%. Much faster than plugging into my computer, which is 500ma max. I don't have any fancy test equipment, and don't claim to know a whole lot about electronics, but seems pretty fast to me.
I have a 4-port 2A 5v USB charger, and connecting it to my Nexus OR Milestone with a MicroUSB cable (the one that shipped with either phone, or the one from my Kindle) yields painfully slow charging - it basically won't charge if you are using the phone.
Connecting the Nexus One charger yields fast charging on either phone - so it is not HTC (or Motorola) proprietary.
The Milestone comes with a 900mA USB plug, and connecting THAT to either phone with either of the MicroUSB cables yields fast charging.
I have another aftermarket 2 port 2A 5V USB wall charger (brand: T'nB) AND I have an iPhone USB plug, and both give fast charging on the Milestone, and I have not yet tried them on the Nexus One.
Breakdown (on things I've tried):
FAST CHARGING on Nexus One AND Milestone:
Nexus charger (either in the US (110v/60hz) or in France (220v/50hz) through an adaptor)
Milestone wall French USB plug (which I think is something odd like 850mA at 5.9v) with ANY microUSB cable (in fact, it seems to charge both of the phones faster than the stock Nexus One plug)
SLOW CHARGING on Nexus One AND Milestone:
USB plug on computer
One aftermarket 4 port 2A 5V USB charger (NOT a hub, only a charger)
FAST CHARGING on Milestone, untested with Nexus One
T'nB 2 port 5v 2A USB wall charger
Apple iPhone 1 port 1A 5v USB wall adaptor
Seems found the answer for Fast Charging N1
I had just do some test for Charging N1 With Original AC Charger , Other band USB Charger and PC USB charger.
1. Orginal Charger give N1 from 0% to 100% at about 2 hour and something.
2. The other band AC charger and PC USB Charger can only finish the same job over 5 to 6 hours.
The Fast Charging is Due to 5.1V (Measured at N1) and 5.2V(Measured inside AC charger). 0.1V Drop is due to resistance of USB cable.
The Slow charged is due to 4.8V (measured at N1) and 5.0V (measured on PC USB and Other AC Charger)
i.e. Original Charger mod from 5.0 V to 5.2V (about 10% increase in Voltage)
Looks my theory is correct then ? N1 watches the voltage and if it droops too much, it backs off the current.
So the key would be: get a charger than can maintain at least 1A @ 5.2V, use
a decent gauge, short wire from the brick to N1.
Has anyone tried a Blackberry charger on the N1? Will they work to full capacity as well? (They're on Amazon for a fiver)
Because the nokia charger is working
http://pinoutsguide.com/CellularPhones-Nokia/micro_usb_connector_pinout.shtml
see info under table.
I tested also HP charger + standard USB cable delivered with Nexus, and it is charching cca 1A.
Then I tested one noname Carcharger + standard USB cable delivered with Nexus, and also charging cca 1A.
I dismantle the noname carcharger and here is a result:
data line (pin2+3) is shorted and connected do + (pin1 ,Vcc) thrue resistor cca 630kOhm.
1 - 4 = 5.1V
2,3 - 4 = 3.2V
rashid11 said:
Looks my theory is correct then ? N1 watches the voltage and if it droops too much, it backs off the current.
So the key would be: get a charger than can maintain at least 1A @ 5.2V, use
a decent gauge, short wire from the brick to N1.
Click to expand...
Click to collapse
I try to use power supply 5.2V 2A with cable without dataline (pin 2and3 not connected) and it is charging 480mA only.
I have now tested with an HTC car charger for the HD2. It's fast charging (tested with Waze running, two bluetooth connections and playing mp3 - and it's still loading the battery, whereas before it would be stuck at the current percentage) and even shows AC power instead of USB.
Hi Here in Mexico dont have a UK plugs and of corse my phone charger dont fits o the outlet but i have a USB Charger I can plug the Data cable to carge but the only question i have is this specs
Samsung Original Travel Charger is output : 5V = 0.7a
My USB output : 5V = 0.5a
Please Help
I think the only diff is the charges Times is less amp takes more time to full the battery.
i use the uk charger here in the u.s. i believe they are set for multiple power inputs just get a cheap adapter to change the plug configuration. that is what i am using.
i posted the below in another charger thread but in case it serves here
not sure if a lot of folks are just unaware, but every phone i've had charged fine from a usb port off my computer
since i started tethering my phone to my laptop (browse the web from family couch) december 2009, i haven't used the wall charger
even if i'm not tethering, i've got a spare usb cable on the desktop, that when i sit down at the desk, the phone or whatever device, gets connected to - far more convenient and fewer items occupying space on the desk
plus, i've got that Tmo car charger that just has a usb port on it's end - so the same cable that i use to tether to the laptop (when in the car), if i'm using the phone in the dock for nav, runs down to the charger - the charger, with no cable hanging off it when not in use, let's me leave the charger in the socket 24/7 - no looking for it in the glove box and untangling it etc
that charger is simply converting the 14V car voltage to 5 V the USB port normally delivers
2 - 3.5 hours seems to take my 1150mah battery from low charge to full
for what it's worth
celtichazard said:
Hi Here in Mexico dont have a UK plugs and of corse my phone charger dont fits o the outlet but i have a USB Charger I can plug the Data cable to carge but the only question i have is this specs
Samsung Original Travel Charger is output : 5V = 0.7a
My USB output : 5V = 0.5a
Please Help
I think the only diff is the charges Times is less amp takes more time to full the battery.
Click to expand...
Click to collapse
There is nothing wrong with that. 5V is all you need. As long as you don't supply too high a voltage, your batteries should be safe. Don't worry about the amperage (current). Lower current (0.5a vs 0.7a) just means that it takes longer to charge the batteries.
And for those who really must have a wall charger that charges the batteries directly, you can buy a universal USB charger (http://www.dealextreme.com/details.dx/sku.15264). It works great. It plugs into any USB charger or laptop USB port, and charges any battery rated 3.7V. You can find them on eBay for just a couple of dollars.
Hello everyone,
So I have been trying to find the answer to what I am wondering but to no avail. I know that when using a charger that did not come with the phone it needs to have to same voltage to not hurt the battery, but I am unsure of the amps. I know for normal powering of things the charger needs to supply the same amount of amps or higher so that the item can pull enough power from the charger. However, phones do not need a certain amps to be powered by the charger. So I want to know if I can use any changer that has 5 volts, but varying amps. This is because I read that if you use a charger with lower amps it is better for the battery as it is not charging as fast increasing the life span of the battery, is this true?
Example: I have a LG G2 which uses a charger with 5V and 1.8A , but I want to use my nexus wireless charger that is 5V and 1.2A
Thanks for any assistance!