Could someone confirm for me which Broadcom chip is in the GT-P5100 Samsung G Tab 2 10.1?
I think it is the BCM4330 but need to be sure for building the Kernel.
patonar said:
Could someone confirm for me which Broadcom chip is in the GT-P5100 Samsung G Tab 2 10.1?
I think it is the BCM4330 but need to be sure for building the Kernel.
Click to expand...
Click to collapse
Any one have any ideas? Currently when i build the kernel from Samsung Open Source the WiFi doesn't work?
Try manually load the wifi driver and then check the error message:
Code:
# insmod /lib/modules/dhd.ko
# dmesg
patonar said:
Any one have any ideas? Currently when i build the kernel from Samsung Open Source the WiFi doesn't work?
Click to expand...
Click to collapse
It doesn't announce the chip type during boot. It does say that it's using the Broadcom Dongle Host Driver (dhd.ko).
Here's the dmesg output right after a boot:
<4>[ 41.208312] C0 [ Thread-106] alloc static buf at ee980000!
<4>[ 41.214172] C0 [ Thread-106] dhdsdio_probe : no mutex held. set lock
<4>[ 41.214385] C0 [ Thread-106] F1 signature read @0x18000000=0x16044330
<4>[ 41.243164] C0 [ Thread-106] DHD: dongle ram size is set to 294912(orig 294912)
<6>[ 41.251251] C0 [wl_event_handle] CFG80211-INFO2) wl_event_handler : tsk Enter, tsk = 0xedd1ee2c
<4>[ 41.251281] C0 [ Thread-106] wl_create_event_handler thr:366 created
<4>[ 41.267120] C0 [ Thread-106] p2p0: P2P Interface Registered
<4>[ 41.272186] C0 [ Thread-106] dhd_attach thr:369 created
<4>[ 41.280029] C0 [ Thread-106] dhd_attach thr:36a created
<4>[ 41.287811] C0 [ Thread-106] dhd_attach thr:36b created
<4>[ 41.395568] C0 [ Thread-106] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
<4>[ 41.518981] C0 [ Thread-106] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
<4>[ 41.525604] C0 [ Thread-106] Firmware up: op_mode=5, Broadcom Dongle Host Driver mac=1c:90:ee
<4>[ 41.529266] C0 [ Thread-106] POWER_VAL = 1
<4>[ 41.539489] C0 [ Thread-106] Firmware version = wl0: Sep 12 2012 18:50:40 version 5.90.125.1209 JB (WFD)
<4>[ 41.539520] C0 [ Thread-106] dhd_net_attach: ifidx 0
<4>[ 41.549743] C0 [ Thread-106] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 1c:90:ee
<4>[ 41.549774] C0 [ Thread-106] dhdsdio_probe : the lock is released.
<4>[ 41.565521] C0 [ Thread-106]
<4>[ 41.565551] C0 [ Thread-106] Dongle Host Driver, version 1.28.11.12 (Add_Patch_1005)
<4>[ 41.565551] C0 [ Thread-106] Compiled in drivers/net/wireless/bcmdhd on Nov 29 2012 at 14:35:07
<4>[ 42.079406] C1 [ wpa_supplicant] dhd_open: Enter, net[edd1e000]
<4>[ 42.079437] C1 [ wpa_supplicant]
<4>[ 42.079437] C1 [ wpa_supplicant] Dongle Host Driver, version 1.28.11.12 (Add_Patch_1005)
<4>[ 42.079437] C1 [ wpa_supplicant] Compiled in drivers/net/wireless/bcmdhd on Nov 29 2012 at 14:35:07
<6>[ 42.083282] C1 [ wpa_supplicant] CFG80211-INFO2) wl_cfg80211_attach_post : p2p0: p2p_dev_addr=1e:90:ee
<4>[ 44.223602] C0 [ wpa_supplicant] dhd_wl_ioctl: WLC_IOCTL: cmd: 23, ret = -17
<4>[ 44.300018] C0 [ wpa_supplicant] dhd_wl_ioctl: WLC_SET_VAR: escan, ret = -16
<6>[ 44.300048] C0 [ wpa_supplicant] CFG80211-INFO2) wl_run_escan : Escan set error (-16)
<6>[ 44.300079] C0 [ wpa_supplicant] CFG80211-INFO2) wl_run_escan : error (-16)
<6>[ 44.300079] C0 [ wpa_supplicant] CFG80211-INFO2) __wl_cfg80211_scan : Scan err = (-16), busy?-16
<6>[ 44.300109] C0 [ wpa_supplicant] CFG80211-INFO2) wl_cfg80211_scan : scan error (-16)
<4>[ 45.324462] C0 [ wpa_supplicant] dhd_wl_ioctl: WLC_SET_VAR: escan, ret = -16
<6>[ 45.324493] C0 [ wpa_supplicant] CFG80211-INFO2) wl_run_escan : Escan set error (-16)
<6>[ 45.324493] C0 [ wpa_supplicant] CFG80211-INFO2) wl_run_escan : error (-16)
<6>[ 45.324523] C0 [ wpa_supplicant] CFG80211-INFO2) __wl_cfg80211_scan : Scan err = (-16), busy?-16
<6>[ 45.324523] C0 [ wpa_supplicant] CFG80211-INFO2) wl_cfg80211_scan : scan error (-16)
<4>[ 45.349548] C0 [wl_event_handle] wl_bss_connect_done succeeded with 0c:31:c0
<4>[ 45.366058] C0 [wl_event_handle] wl_bss_connect_done succeeded with 0c:31:c0
<6>[ 45.366088] C0 [wl_event_handle] CFG80211-INFO2) wl_bss_connect_done : Connected event of connected device e=0 s=0, ignore it
<6>[ 45.416717] C1 [ wpa_supplicant] CFG80211-TRACE) wl_cfg80211_set_btcoex_dhcp : wl_cfg80211_set_btcoex_dhcp: DHCP session starts
<6>[ 46.010528] C0 [ wpa_supplicant] CFG80211-TRACE) wl_cfg80211_set_btcoex_dhcp : wl_cfg80211_set_btcoex_dhcp: DHCP is complete
<3>[ 47.232666] C0 [ init] init: sys_prop: permission denied uid:1003 name:boot.sfbootcomplete
<3>[ 47.234222] C0 [ init] init: sys_prop: permission denied uid:1003 name:service.bootanim.exit
Click to expand...
Click to collapse
My dmesg output, others message not related to wifi removed:
wifi_set_power = 1
<4>[ 1406.053222] C1 [ Thread-159] wifi_set_carddetect = 1
<6>[ 1406.199890] C0 [ kworker/u:0] mmc2: new high speed SDIO card at address 0001
<4>[ 1406.207122] C1 [ Thread-159] alloc static buf at ee940000!
<4>[ 1406.208099] C0 [ Thread-159] dhdsdio_probe : no mutex held. set lock
<4>[ 1406.208526] C0 [ Thread-159] F1 signature read @0x18000000=0x16044330
<4>[ 1406.220153] C0 [ Thread-159] DHD: dongle ram size is set to 294912(orig 294912)
<4>[ 1406.222290] C0 [ Thread-159] wl_create_event_handler thr:dfd created
<6>[ 1406.223876] C1 [wl_event_handle] CFG80211-INFO2) wl_event_handler : tsk Enter, tsk = 0xed56962c
<4>[ 1406.232330] C1 [ Thread-159] p2p0: P2P Interface Registered
<4>[ 1406.235717] C1 [ Thread-159] dhd_attach thr:dfe created
<4>[ 1406.235839] C1 [ Thread-159] dhd_attach thr:dff created
<4>[ 1406.235961] C1 [ Thread-159] dhd_attach thr:e00 created
<4>[ 1406.283935] C0 [ Thread-159] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
<4>[ 1406.407928] C0 [ Thread-159] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
<4>[ 1406.414093] C0 [ Thread-159] Firmware up: op_mode=5, Broadcom Dongle Host Driver mac=50:84:55
<4>[ 1406.417572] C0 [ Thread-159] POWER_VAL = 1
<4>[ 1406.425750] C0 [ Thread-159] Firmware version = wl0: Nov 27 2012 22:17:33 version 5.99.8 (JB) (WFD) (CCX)
<4>[ 1406.425781] C0 [ Thread-159] dhd_net_attach: ifidx 0
<4>[ 1406.443572] C0 [ Thread-159] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 50:84:55
<4>[ 1406.443603] C0 [ Thread-159] dhdsdio_probe : the lock is released.
<4>[ 1406.444915] C0 [ Thread-159]
<4>[ 1406.444915] C0 [ Thread-159] Dongle Host Driver, version 1.28.11.12 (Add_Patch_1005)
<4>[ 1406.444915] C0 [ Thread-159] Compiled in drivers/net/wireless/bcmdhd on Jan 17 2013 at 22:22:11
<4>[ 1406.576934] C1 [ wpa_supplicant] dhd_open: Enter, net[ed56b800]
<4>[ 1406.576965] C1 [ wpa_supplicant]
<4>[ 1406.576965] C1 [ wpa_supplicant] Dongle Host Driver, version 1.28.11.12 (Add_Patch_1005)
<4>[ 1406.576965] C1 [ wpa_supplicant] Compiled in drivers/net/wireless/bcmdhd on Jan 17 2013 at 22:22:11
<6>[ 1406.587585] C0 [ wpa_supplicant] CFG80211-INFO2) wl_cfg80211_attach_post : p2p0: p2p_dev_addr=52:84:55
<3>[ 1406.823181] C0 [ wpa_supplicant] WLDEV-ERROR) wldev_set_country : wldev_set_country: set country for ID as ID rev -1
<7>[ 1416.820709] C0 [ swapper] wlan0: no IPv6 routers present
<7>[ 1417.211791] C1 [ swapper] p2p0: no IPv6 routers present
dhd_wl_ioctl: WLC_IOCTL: cmd: 23, ret = -17
<6>[ 1421.942199] C1 [wl_event_handle] CFG80211-INFO2) wl_escan_handler : unexpected Escan Event 10 : abort
<4>[ 1422.309417] C1 [wl_event_handle] wl_bss_connect_done succeeded with b2:6b:cf
<6>[ 1422.316711] C1 [ wpa_supplicant] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<4>[ 1422.330352] C1 [wl_event_handle] wl_bss_connect_done succeeded with b2:6b:cf
<6>[ 1422.330383] C1 [wl_event_handle] CFG80211-INFO2) wl_bss_connect_done : Connected event of connected device e=0 s=0, ignore it
<6>[ 1422.377410] C1 [ wpa_supplicant] CFG80211-TRACE) wl_cfg80211_set_btcoex_dhcp : wl_cfg80211_set_btcoex_dhcp: DHCP session starts
<6>[ 1425.287078] C0 [ wpa_supplicant] CFG80211-TRACE) wl_cfg80211_set_btcoex_dhcp : wl_cfg80211_set_btcoex_dhcp: DHCP is complete
Click to expand...
Click to collapse
Hi,
My TF700 is stuck on CWM 6.0.1.3 (non touch) recovery screen, it always goes there.
I was now able to use adb command (it shows serial no 0123456789ABCDE is it normal?).
Fastboot does not work
Can i do something to recover my TF700?
Thanks for your help.
Kalimeruh said:
Hi,
My TF700 is stuck on CWM 6.0.1.3 (non touch) recovery screen, it always goes there.
I was now able to use adb command (it shows serial no 0123456789ABCDE is it normal?).
Fastboot does not work
Can i do something to recover my TF700?
Thanks for your help.
Click to expand...
Click to collapse
What bootloader version do you have? (4.1.1 or 4.2.1)? can you boot into the OS?
buhohitr said:
What bootloader version do you have? (4.1.1 or 4.2.1)? can you boot into the OS?
Click to expand...
Click to collapse
I think it is 4.2.1. I only can get to the CWM recovery (directly).
Kalimeruh said:
I think it is 4.2.1. I only can get to the CWM recovery (directly).
Click to expand...
Click to collapse
Did you try to use CWM to reflash rom/kernel?
buhohitr said:
Did you try to use CWM to reflash rom/kernel?
Click to expand...
Click to collapse
The volume + and - do not work. I'm only able to select option reboot system now.
Is there something that i can do from adb? It is seems to be the only way i can communicate with the tablet.
Kalimeruh said:
The volume + and - do not work. I'm only able to select option reboot system now.
Is there something that i can do from adb? It is seems to be the only way i can communicate with the tablet.
Click to expand...
Click to collapse
I see, OK let do this:
1) Download full Asus firmware and unzip all the way until you see the "blob" file
2) Copy the blob file to your Micro sdcard using your PC then then insert the card back into your tablet
3) On your PC, execute the following adb commands:
adb shell hit enter(you are going to see bunch of weird characters, this's normal)
dd if=/Removable/MicroSD/blob of=/dev/block/mmcblk0p4 hit enter and wait for around 10-20min.
Update process will start and table will reboot once done. Remember you will have stock rom and recovery back once done.
buhohitr said:
I see, OK let do this:
1) Download full Asus firmware and unzip all the way until you see the "blob" file
2) Copy the blob file to your Micro sdcard using your PC then then insert the card back into your tablet
3) On your PC, execute the following adb commands:
adb shell hit enter(you are going to see bunch of weird characters, this's normal)
dd if=/Removable/MicroSD/blob of=/dev/block/mmcblk0p4 hit enter and wait for around 10-20min.
Update process will start and table will reboot once done. Remember you will have stock rom and recovery back once done.
Click to expand...
Click to collapse
Thanks for your reply
I got an error "/Removable/MicroSD/blob no such file or directory".
I'm trying now the abd push blob /sdcard/blob and then i'll do the rest on the command line afterwards.
Do you think it will work?
[Update] Didn't work
When the tablet is connected to the pc the screen is always showing "CWM 6.0.1.3", does that have any influence?
Thanks
I saw that i'm also able to use nvflash and wheelie.
The only command i cannot use is fastboot
Can somebody please help me?
Kalimeruh said:
I saw that i'm also able to use nvflash and wheelie.
The only command i cannot use is fastboot
Can somebody please help me?
Click to expand...
Click to collapse
If you post error messages instead of "doesn't work", maybe.
You said you cannot use fastboot - why?
You said you are able to use nvflash and wheelie, does that mean you also have the required files like "blob.bin", "bricksafe.img" etc.?
_that said:
If you post error messages instead of "doesn't work", maybe.
You said you cannot use fastboot - why?
You said you are able to use nvflash and wheelie, does that mean you also have the required files like "blob.bin", "bricksafe.img" etc.?
Click to expand...
Click to collapse
Basically because i don't have error messages.
I cannot use the fastboot because the tablet is stuck on the screen of the CWM i cannot got out. Either it is on recovery mode or on APX... When i use fastboot command cmd cannot find devices.
Regarding nvflash and wheelie is means that i am able to communicate with the tablet. I have one ebtblob.bin, i tried but i got one error ]Failed to read RCMVERS from blob file.
Can you give me a hint?
Thanks
Kalimeruh said:
I cannot use the fastboot because the tablet is stuck on the screen of the CWM i cannot got out. Either it is on recovery mode or on APX... When i use fastboot command cmd cannot find devices.
Click to expand...
Click to collapse
What happens when you try to enter the bootloader menu? (hold Volume-left while turning the tablet on)
Kalimeruh said:
Regarding nvflash and wheelie is means that i am able to communicate with the tablet. I have one ebtblob.bin, i tried but i got one error ]Failed to read RCMVERS from blob file.
Can you give me a hint?
Click to expand...
Click to collapse
So you don't have a blob for your device, which means you can't use nvflash.
Since you can communicate with the recovery via adb, please post the output of
Code:
adb shell ls -l /dev/block/mmc*
to see if your recovery can access the internal storage.
_that said:
What happens when you try to enter the bootloader menu? (hold Volume-left while turning the tablet on)
It goes directly to CWM 6.0.1.3 (non touch version) where i cannot do anything because volume up and down do not work.
So you don't have a blob for your device, which means you can't use nvflash.
Since you can communicate with the recovery via adb, please post the output of
Code:
adb shell ls -l /dev/block/mmc*
to see if your recovery can access the internal storage.
Click to expand...
Click to collapse
brw------- 1 root root 179, 0 Jan 19 15:52 /dev/block/mmcblk0
brw------- 1 root root 179, 1 Jan 19 15:52 /dev/block/mmcblk0p1
-rw-rw-rw- 1 root root 1088 Jan 19 15:52 /dev/block/mmcblk0p3
Kalimeruh said:
brw------- 1 root root 179, 0 Jan 19 15:52 /dev/block/mmcblk0
brw------- 1 root root 179, 1 Jan 19 15:52 /dev/block/mmcblk0p1
-rw-rw-rw- 1 root root 1088 Jan 19 15:52 /dev/block/mmcblk0p3
Click to expand...
Click to collapse
That's very bad - it should show at least mmcblk0p1 to mmcblk0p8. That means you can't use the recovery to modify anything on your internal storage.
How did you get into this situation? "Wipe data" in the bootloader menu?
_that said:
That's very bad - it should show at least mmcblk0p1 to mmcblk0p8. That means you can't use the recovery to modify anything on your internal storage.
How did you get into this situation? "Wipe data" in the bootloader menu?
Click to expand...
Click to collapse
This happened since i've installed CWM 6.0.1.3, i'm not able to do anything.
Is there any solution?
Kalimeruh said:
This happened since i've installed CWM 6.0.1.3, i'm not able to do anything.
Is there any solution?
Click to expand...
Click to collapse
If you can't get fastboot to work, I have no other idea.
_that said:
If you can't get fastboot to work, I have no other idea.
Click to expand...
Click to collapse
Will this http://forum.xda-developers.com/showthread.php?t=1994705 work for me?
Kalimeruh said:
Will this http://forum.xda-developers.com/showthread.php?t=1994705 work for me?
Click to expand...
Click to collapse
No, that requires a running Android system, or at least a recovery that can access your internal storage.
To get more info about your problem, reboot your tablet and run the following command on your computer:
Code:
adb shell dmesg > dmesg.txt
and post the resulting file.
Also try this:
Code:
adb shell hexdump -C -s 0x380000 -n 8 /dev/block/mmcblk0
and tell me if it outputs "ANDROID!" (after some hexadecimal numbers).
_that said:
No, that requires a running Android system, or at least a recovery that can access your internal storage.
To get more info about your problem, reboot your tablet and run the following command on your computer:
Code:
adb shell dmesg > dmesg.txt
and post the resulting file.
Click to expand...
Click to collapse
Here you are:
<6>[ 0.000000] Initializing cgroup subsys cpu
<5>[ 0.000000] Linux version 2.6.39.4-cyanogenmod-g80ca3c6 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Sep 14 10:04:19 MST 2012
<4>[ 0.000000] CPU: ARMv7 Processor [412fc099] revision 9 (ARMv7), cr=10c5387f
<4>[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
<4>[ 0.000000] Machine: cardhu
<4>[ 0.000000] Ignoring unrecognised tag 0x41000801
<4>[ 0.000000] Ignoring unrecognised tag 0x41000801
<4>[ 0.000000] Ignoring unrecognised tag 0x41000801
<4>[ 0.000000] Ignoring unrecognised tag 0x41000801
<4>[ 0.000000] Ignoring unrecognised tag 0x41000801
<4>[ 0.000000] Ignoring unrecognised tag 0x41000801
<4>[ 0.000000] Ignoring unrecognised tag 0x41000801
<6>[ 0.000000] Found tegra_fbmem: [email protected]
<6>[ 0.000000] Tegra reserved memory:
<6>[ 0.000000] LP0: bddf9000 - bddfafff
<6>[ 0.000000] Bootloader framebuffer: abc01000 - ac4cbfff
<6>[ 0.000000] Framebuffer: bec00000 - bf4fffff
<6>[ 0.000000] 2nd Framebuffer: bf500000 - bfdfffff
<6>[ 0.000000] Carveout: 00000000 - 00000000
<6>[ 0.000000] Vpr: 00000000 - 00000000
<4>[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
<7>[ 0.000000] On node 0 totalpages: 256768
<7>[ 0.000000] free_area_init_node: node 0, pgdat c082d200, node_mem_map c0989000
<7>[ 0.000000] Normal zone: 1536 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 195072 pages, LIFO batch:31
<7>[ 0.000000] HighMem zone: 508 pages used for memmap
<7>[ 0.000000] HighMem zone: 59652 pages, LIFO batch:15
<6>[ 0.000000] Tegra3: CPU Speedo ID 5, CPU Process ID 3, Soc Speedo ID 2
<6>[ 0.000000] Tegra Revision: A03 SKU: 0x80 CPU Process: 3 Core Process: 0
<6>[ 0.000000] tegra: PLLP fixed rate: 408000000
<6>[ 0.000000] [MISC]: adopt kernel cmdline prior to tegra3_get_project_id ready.
<4>[ 0.000000] Lowering cpu_lp maximum rate from 620000000 to 513000000
<4>[ 0.000000] Lowering sbus maximum rate from 334000000 to 267000000
<4>[ 0.000000] Lowering vi maximum rate from 425000000 to 409000000
<4>[ 0.000000] Lowering vde maximum rate from 600000000 to 437000000
<4>[ 0.000000] Lowering mpe maximum rate from 600000000 to 446000000
<4>[ 0.000000] Lowering 2d maximum rate from 600000000 to 446000000
<4>[ 0.000000] Lowering epp maximum rate from 600000000 to 446000000
<4>[ 0.000000] Lowering 3d maximum rate from 600000000 to 446000000
<4>[ 0.000000] Lowering 3d2 maximum rate from 600000000 to 446000000
<4>[ 0.000000] Lowering se maximum rate from 600000000 to 446000000
<4>[ 0.000000] Lowering host1x maximum rate from 300000000 to 267000000
<4>[ 0.000000] Lowering cbus maximum rate from 700000000 to 437000000
<4>[ 0.000000] Lowering pll_c maximum rate from 1400000000 to 1066000000
<4>[ 0.000000] Lowering ndflash maximum rate from 240000000 to 200000000
<4>[ 0.000000] Lowering sbc1 maximum rate from 160000000 to 100000000
<4>[ 0.000000] Lowering sbc2 maximum rate from 160000000 to 100000000
<4>[ 0.000000] Lowering sbc3 maximum rate from 160000000 to 100000000
<4>[ 0.000000] Lowering sbc4 maximum rate from 160000000 to 100000000
<4>[ 0.000000] Lowering sbc5 maximum rate from 160000000 to 100000000
<4>[ 0.000000] Lowering sbc6 maximum rate from 160000000 to 100000000
<4>[ 0.000000] Lowering dsia maximum rate from 500000000 to 275000000
<4>[ 0.000000] Lowering dsib maximum rate from 500000000 to 275000000
<4>[ 0.000000] Lowering cpu_g maximum rate from 1900000000 to 1370000000
<4>[ 0.000000] Keep max_rate of cpu_g as 1900000000
<4>[ 0.000000] max_millivolts of cpu_g is d->max_millivolts =1275
<4>[ 0.000000] tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
<4>[ 0.000000] tegra3_dvfs: cold offset 50000000 is too high for regular dvfs limit 1000000
<6>[ 0.000000] tegra dvfs: VDD_CPU nominal 1075mV, scaling enabled
<6>[ 0.000000] tegra dvfs: VDD_CORE nominal 1200mV, scaling enabled
<6>[ 0.000000] L310 cache controller enabled
<6>[ 0.000000] l2x0: 8 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7c080001, Cache size: 1048576 B
<6>[ 0.000000] PERCPU: Embedded 8 pages/cpu @c1191000 s8992 r8192 d15584 u32768
<7>[ 0.000000] pcpu-alloc: s8992 r8192 d15584 u32768 alloc=8*4096
<7>[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 254724
<5>[ 0.000000] Kernel command line: tegraid=30.1.3.0.0 [email protected] commchip_id=0 androidboot.serialno=015d2d431f0c0208 androidboot.commchip_id=0 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 usbcore.old_scheme_first=1 [email protected] [email protected] core_edp_mv=0 audio_codec=wm8903 board_info=245:0:14:ed:28 tegraboot=sdmmc gpt gpt_sector=62078975 android.kerneltype=recovery androidboot.productid=0x04 androidboot.carrier=wifi-only
<6>[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 0.000000] Memory: 1003MB = 1003MB total
<5>[ 0.000000] Memory: 997352k/997352k available, 49176k reserved, 240632K highmem
<5>[ 0.000000] Virtual kernel memory layout:
<5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
<5>[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
<5>[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
<5>[ 0.000000] vmalloc : 0xf0800000 - 0xf8000000 ( 120 MB)
<5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
<5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
<5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
<5>[ 0.000000] .init : 0xc0008000 - 0xc0042000 ( 232 kB)
<5>[ 0.000000] .text : 0xc0042000 - 0xc075ce44 (7276 kB)
<5>[ 0.000000] .data : 0xc075e000 - 0xc082edc0 ( 836 kB)
<6>[ 0.000000] Preemptable hierarchical RCU implementation.
<6>[ 0.000000] RCU-based detection of stalled CPUs is disabled.
<6>[ 0.000000] Verbose stalled-CPUs detection is disabled.
<6>[ 0.000000] NR_IRQS:800
<6>[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
<6>[ 0.000202] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
<6>[ 0.040062] pid_max: default: 32768 minimum: 301
<6>[ 0.040237] Mount-cache hash table entries: 512
<6>[ 0.040960] Initializing cgroup subsys debug
<6>[ 0.040972] Initializing cgroup subsys cpuacct
<6>[ 0.041033] Initializing cgroup subsys freezer
<6>[ 0.041060] CPU: Testing write buffer coherency: ok
<6>[ 0.041304] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
<4>[ 0.161490] CPU1: Booted secondary processor
<4>[ 0.221464] CPU2: Booted secondary processor
<4>[ 0.281459] CPU3: Booted secondary processor
<6>[ 0.301280] Brought up 4 CPUs
<6>[ 0.301291] SMP: Total of 4 processors activated (3984.58 BogoMIPS).
<6>[ 0.304893] print_constraints: dummy:
<6>[ 0.305082] NET: Registered protocol family 16
<6>[ 0.305853] host1x bus init
<6>[ 0.306779] [MISC]: adopt kernel cmdline prior to tegra3_get_project_id ready.
<6>[ 0.306788] [MISC]: adopt kernel cmdline prior to tegra3_get_project_id ready.
<4>[ 0.307991] Check TF700T pinmux
<4>[ 0.308115] tegra_booting_info reg=0
<4>[ 0.308121] tegra_booting_info-normal
<6>[ 0.308489] cardhu_edp_init : use asus edp policy
<6>[ 0.308534] Selecting UARTA as the debug console
<4>[ 0.308547] console_none_on_cmdline+uart_debug_init
<6>[ 0.308554] The debug console clock name is uarta_dbg
<6>[ 0.309757] ram_console: got buffer at beb00000, size 100000
<6>[ 0.309937] ram_console: uncorrectable error in header
<6>[ 0.309946] ram_console: no valid data in buffer (sig = 0x02034044)
<6>[ 0.324235] console [ram-1] enabled
<6>[ 0.324550] TPS6591x GPIO2 was reprogrammed to follow state of SLEEP input
<6>[ 0.324735] Registering the device TPS62361B
<6>[ 0.451272] Registering tegra-kbc
<6>[ 0.451437] Registering gpio keys
<4>[ 0.451665] Check TF202T setting
<4>[ 0.451669]
<6>[ 0.494957] fjm6mo i2c_register_board_info
<6>[ 0.495151] mi1040 i2c_register_board_info
<6>[ 0.495413] iCatch7002a i2c_register_board_info
<6>[ 0.495603] *** MPU START *** cardhu_mpuirq_init...
<6>[ 0.495871] initial mpu with TF700T config...
<6>[ 0.495971] *** MPU END *** mpuirq_init...
<7>[ 0.496177] gpio_request: gpio-72 (GMI_CS0) status -16
<3>[ 0.496354] set_unused_pin_gpio() Error in gpio_request() for gpio 72
<7>[ 0.496451] gpio_request: gpio-74 (GMI_CS1) status -16
<3>[ 0.496625] set_unused_pin_gpio() Error in gpio_request() for gpio 74
<7>[ 0.496725] gpio_request: gpio-83 (GMI_CS2) status -16
<3>[ 0.496900] set_unused_pin_gpio() Error in gpio_request() for gpio 83
<4>[ 0.497003] BOARD_PM269:TF700T_Elpida 800 MHZ version 5 (0413)
<3>[ 0.497260] tegra: invalid EMC DFS table: maximum rate 800000 kHz does not match nominal voltage 1200
<6>[ 0.497521] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
<6>[ 0.497622] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
<6>[ 0.497813] hw-breakpoint: maximum watchpoint size is 4 bytes.
<6>[ 0.498252] tegra_iovmm_register: added iovmm-smmu
<6>[ 0.504633] bio: create slab <bio-0> at 0
<6>[ 0.505324] vgaarb: loaded
<4>[ 0.505471] i2c-core: driver [tps6591x] using legacy suspend method
<4>[ 0.505646] i2c-core: driver [tps6591x] using legacy resume method
<4>[ 0.505840] i2c-core: driver [tps80031] using legacy suspend method
<4>[ 0.505936] i2c-core: driver [tps80031] using legacy resume method
<4>[ 0.506150] i2c-core: driver [ricoh583] using legacy suspend method
<4>[ 0.506247] i2c-core: driver [ricoh583] using legacy resume method
<5>[ 0.506682] SCSI subsystem initialized
<6>[ 0.506863] tegra-otg tegra-otg: otg transceiver registered
<6>[ 0.507185] usbcore: registered new interface driver usbfs
<6>[ 0.507350] usbcore: registered new interface driver hub
<6>[ 0.507624] usbcore: registered new device driver usb
<6>[ 0.509175] tps6591x 4-002d: VERNUM is 02
<6>[ 0.531278] Wake18 for irq=118
<6>[ 0.531452] Enabling wake18
<6>[ 0.531881] print_constraints: tps6591x_VIO: 1500 <--> 3300 mV at 1800 mV normal standby
<6>[ 0.532706] print_constraints: tps6591x_VDD_1: 600 <--> 1500 mV at 600 mV normal standby
<6>[ 0.533285] print_constraints: tps6591x_VDD_2: 600 <--> 1500 mV at 1200 mV normal standby
<6>[ 0.534152] print_constraints: tps6591x_VDDCTRL: 600 <--> 1400 mV at 1025 mV normal standby
<6>[ 0.534658] print_constraints: tps6591x_LDO_1: 1000 <--> 3300 mV at 2850 mV normal standby
<6>[ 0.534774] set_supply: tps6591x_LDO_1: supplied by tps6591x_VDD_2
<6>[ 0.535285] print_constraints: tps6591x_LDO_2: 1050 <--> 3300 mV at 1000 mV normal standby
<6>[ 0.535477] set_supply: tps6591x_LDO_2: supplied by tps6591x_VDD_2
<6>[ 0.535855] print_constraints: tps6591x_LDO_3: 1000 <--> 3300 mV at 1000 mV normal standby
<6>[ 0.536366] print_constraints: tps6591x_LDO_4: 1000 <--> 3300 mV at 1200 mV normal standby
<6>[ 0.536799] print_constraints: tps6591x_LDO_5: 1000 <--> 3300 mV at 1000 mV normal standby
<6>[ 0.537350] print_constraints: tps6591x_LDO_6: 1200 mV normal standby
<6>[ 0.537544] set_supply: tps6591x_LDO_6: supplied by tps6591x_VIO
<6>[ 0.538307] print_constraints: tps6591x_LDO_7: 1200 mV normal standby
<6>[ 0.538422] set_supply: tps6591x_LDO_7: supplied by tps6591x_VIO
<6>[ 0.539020] print_constraints: tps6591x_LDO_8: 1000 <--> 3300 mV at 1000 mV normal standby
<6>[ 0.539136] set_supply: tps6591x_LDO_8: supplied by tps6591x_VIO
<6>[ 0.539911] tps6591x register misc device for I2C stress test rc=0
<6>[ 0.546588] Advanced Linux Sound Architecture Driver Version 1.0.24.
<6>[ 0.547109] Bluetooth: Core ver 2.16
<6>[ 0.547243] NET: Registered protocol family 31
<6>[ 0.547419] Bluetooth: HCI device and connection manager initialized
<6>[ 0.547518] Bluetooth: HCI socket layer initialized
<6>[ 0.547689] Bluetooth: L2CAP socket layer initialized
<6>[ 0.547869] Bluetooth: SCO socket layer initialized
<6>[ 0.548319] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 0.549190] print_constraints: fixed_reg_en_5v_cp: 5000 mV normal standby
<6>[ 0.550120] print_constraints: fixed_reg_en_5v0: 5000 mV normal standby
<6>[ 0.550848] print_constraints: fixed_reg_en_ddr: 1500 mV normal standby
<6>[ 0.551481] print_constraints: fixed_reg_en_3v3_sys: 3300 mV normal standby
<6>[ 0.552013] print_constraints: fixed_reg_en_3v3_modem: 3300 mV normal standby
<6>[ 0.552312] print_constraints: fixed_reg_cam1_ldo_en: 2800 mV normal standby
<6>[ 0.552500] set_supply: fixed_reg_cam1_ldo_en: supplied by fixed_reg_en_3v3_sys
<6>[ 0.552783] print_constraints: fixed_reg_cam2_ldo_en: 2800 mV normal standby
<6>[ 0.552892] set_supply: fixed_reg_cam2_ldo_en: supplied by fixed_reg_en_3v3_sys
<6>[ 0.553235] print_constraints: fixed_reg_cam3_ldo_en: 3300 mV normal standby
<6>[ 0.553337] set_supply: fixed_reg_cam3_ldo_en: supplied by fixed_reg_en_3v3_sys
<6>[ 0.553699] print_constraints: fixed_reg_en_vdd_com: 3300 mV normal standby
<6>[ 0.553887] set_supply: fixed_reg_en_vdd_com: supplied by fixed_reg_en_3v3_sys
<6>[ 0.554179] print_constraints: fixed_reg_en_3v3_fuse: 3300 mV normal standby
<6>[ 0.554368] set_supply: fixed_reg_en_3v3_fuse: supplied by fixed_reg_en_3v3_sys
<6>[ 0.554734] print_constraints: fixed_reg_en_3v3_emmc: 3300 mV normal standby
<6>[ 0.554840] set_supply: fixed_reg_en_3v3_emmc: supplied by fixed_reg_en_3v3_sys
<6>[ 0.555207] print_constraints: fixed_reg_en_1v8_cam: 1800 mV normal standby
<6>[ 0.555317] set_supply: fixed_reg_en_1v8_cam: supplied by tps6591x_VIO
<6>[ 0.555717] print_constraints: fixed_reg_dis_5v_switch: 5000 mV normal standby
<6>[ 0.555905] set_supply: fixed_reg_dis_5v_switch: supplied by fixed_reg_en_5v0
<6>[ 0.556322] print_constraints: fixed_reg_en_vdd_bl: 5000 mV normal standby
<6>[ 0.556692] print_constraints: fixed_reg_en_vdd_pnl1: 3300 mV normal standby
<6>[ 0.556880] set_supply: fixed_reg_en_vdd_pnl1: supplied by fixed_reg_en_3v3_sys
<6>[ 0.558281] print_constraints: tps62361B: 500 <--> 1770 mV at 1160 mV normal standby
<6>[ 0.558641] tps6236x register misc device for I2C stress test rc=0 tps->chip_id=1 chip_id=87
<6>[ 0.559016] print_constraints: gpio-switch-en_usb1_vbus_oc: 5000 mV normal standby
<7>[ 0.559176] gpio_request: gpio-122 (gpio-switch-en_vddio_vid_oc) status -16
<3>[ 0.559360] gpio-switch-regulator gpio-switch-regulator.17: Unable to request gpio 122
<3>[ 0.559540] gpio-switch-regulator gpio-switch-regulator.17: Unable to register regulator gpio-switch-en_vddio_vid_oc
<6>[ 0.559810] tegra: started io power detection dynamic control
<6>[ 0.559909] tegra: NO_IO_POWER setting 0x1200
<6>[ 0.560008] Switching to clocksource timer_us
<4>[ 0.560208] stop_machine_cpu_stop cpu=1
<4>[ 0.560216] stop_machine_cpu_stop cpu=2
<4>[ 0.560223] stop_machine_cpu_stop cpu=3
<4>[ 0.560230] stop_machine_cpu_stop cpu=0
<4>[ 0.560667] __stop_cpus: wait_for_completion_timeout+
<4>[ 0.560842] __stop_cpus: smp=0 done.executed=1 done.ret =0-
<6>[ 0.561290] Switched to NOHz mode on CPU #0
<6>[ 0.561498] Switched to NOHz mode on CPU #3
<6>[ 0.561505] Switched to NOHz mode on CPU #2
<6>[ 0.561535] Switched to NOHz mode on CPU #1
<6>[ 0.562155] tegra-nvmap tegra-nvmap: created carveout iram (255KiB)
<6>[ 0.563130] NET: Registered protocol family 2
<6>[ 0.563473] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[ 0.564003] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>[ 0.565699] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
<6>[ 0.566618] TCP: Hash tables configured (established 131072 bind 65536)
<6>[ 0.566795] TCP reno registered
<6>[ 0.566894] UDP hash table entries: 512 (order: 2, 16384 bytes)
<6>[ 0.567092] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
<6>[ 0.567607] NET: Registered protocol family 1
<6>[ 0.568039] RPC: Registered udp transport module.
<6>[ 0.568140] RPC: Registered tcp transport module.
<6>[ 0.568316] RPC: Registered tcp NFSv4.1 backchannel transport module.
<7>[ 0.568416] PCI: CLS 0 bytes, default 32
<6>[ 0.568662] Unpacking initramfs...
<6>[ 0.647416] Freeing initrd memory: 1796K
<6>[ 0.647648] PMU: registered new PMU device of type 0
<6>[ 0.648210] Tegra auto-hotplug initialized: disabled
<4>[ 0.648312] tegra_cpufreq_init freq_table_size=14
<6>[ 0.648414] cpu-tegra: init EDP limit: 1550 MHz
<4>[ 0.648629] tegra_cpu_init : emc_clk->min_rate to 204M
<4>[ 0.648889] [Warning]tegra3_cpu_clk_set_rate set vdd_cpu as power source for cpu_g reg=ef946120
<4>[ 0.649296] tegra_cpu_init : emc_clk->min_rate to 204M
<4>[ 0.649486] tegra_cpu_init : emc_clk->min_rate to 204M
<4>[ 0.649672] tegra_cpu_init : emc_clk->min_rate to 204M
<6>[ 0.649939] vibrator_init+ #####
<6>[ 0.650191] vibrator_init- #####
<4>[ 0.670855] highmem bounce pool size: 64 pages
<6>[ 0.671113] ashmem: initialized
<6>[ 0.672253] fuse init (API version 7.16)
<6>[ 0.672490] Registering char device tf_driver (122:0)
<6>[ 0.673537] io scheduler noop registered
<6>[ 0.673702] io scheduler deadline registered
<6>[ 0.673831] io scheduler cfq registered (default)
<4>[ 0.674167] Check create a new adapter
<6>[ 0.694086] tegra_grhost tegra_grhost: initialized
<6>[ 0.694220] tegra_dc_module_init+ #####
<6>[ 0.694464] tegra_dc_module_init- #####
<4>[ 0.694926] Disp: diff_msec= 5938
<4>[ 0.695086] Check cardhu_panel_enable
<4>[ 0.695245] Check panel is panasonic
<4>[ 0.720676] Check power on/off for bridge IC
<4>[ 0.720766] Check enable TF301_1.8V
<4>[ 0.730939] Check enable TF301_I2C_Switch
<4>[ 0.741042] Check enable TF301_OSC
<4>[ 0.761127] Check tegra_dc_rgb_enable
<4>[ 0.761283] Check set polarity
<6>[ 0.761414] tegradc tegradc.0: probed
<6>[ 0.761710] tegradc tegradc.0: probed
<6>[ 0.762070] Wake4 for irq=335
<6>[ 0.762575] nvhdcp: using "always on" policy.
<6>[ 0.762920] tegradc tegradc.1: probed
<6>[ 0.763234] tegradc tegradc.1: probed
<3>[ 0.763345] hdmi: couldn't get regulator vdd_hdmi_con
<6>[ 0.763442] Wake4 for irq=335
<6>[ 0.763603] Enabling wake4
<6>[ 0.763692] gpio bank wake found: wake4 for irq=67
<6>[ 0.763779] Enabling wake4
<6>[ 0.764160] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
<6>[ 1.410772] serial8250.0: ttyS0 at MMIO 0x70006000 (irq = 68) is a Tegra
<6>[ 3.026014] console [ttyS0] enabled
<6>[ 3.150802] tegra_uart_init+ #####
<6>[ 3.154346] tegra_uart.1: ttyHS1 at I/O 0x0 (irq = 69) is a unknown
<6>[ 3.310681] Registered UART port ttyHS1
<6>[ 3.314658] tegra_uart.2: ttyHS2 at I/O 0x0 (irq = 78) is a unknown
<6>[ 3.470679] Registered UART port ttyHS2
<6>[ 3.474652] tegra_uart.3: ttyHS3 at I/O 0x0 (irq = 122) is a unknown
<6>[ 3.630680] Registered UART port ttyHS3
<6>[ 3.634653] tegra_uart.4: ttyHS4 at I/O 0x0 (irq = 123) is a unknown
<6>[ 3.790678] Registered UART port ttyHS4
<6>[ 3.794737] tegra_uart_init- #####
<6>[ 3.798212] Initialized tegra uart driver
<6>[ 3.804472] loop: module loaded
<4>[ 3.807866] i2c-core: driver [apds9802als] using legacy suspend method
<4>[ 3.814485] i2c-core: driver [apds9802als] using legacy resume method
<4>[ 3.821122] nct1008_probe+
<4>[ 3.823926] nct1008_power_control
<6>[ 3.827318] nct1008 4-004c: success in enabling rail vdd_nct1008
<6>[ 3.835702] nct1008 register misc device for I2C stress test rc=0
<6>[ 3.841955] nct1008 4-004c: nct1008_probe: initialized
<4>[ 3.921247] nct1008_get_temp: ret temp=26C
<4>[ 3.926344] nct1008_get_temp: ret temp=26C
<4>[ 3.930969] tegra_watchdog_enable timeout=45
<4>[ 3.935316] nct1008_probe-
<4>[ 3.938136] i2c-core: driver [nct1008] using legacy suspend method
<4>[ 3.944472] i2c-core: driver [nct1008] using legacy resume method
<6>[ 3.950646] bcm4329_rfkill_init+ #####
<4>[ 3.954610] bcm4329_rfkill_probe: can't find bcm4329_32k_clk. assuming 32k clock to chip
<4>[ 3.963042] bcm4329_rfkill_probe : can't find reset gpio.
<6>[ 3.968699] bcm4329_rfkill_init- #####
<6>[ 3.972533] mpu_init+ #####
<6>[ 3.975401] mpu_init- #####
<6>[ 3.978400] kxtf9_mod_init+ #####
<6>[ 3.981806] kxtf9_mod_init- #####
<6>[ 3.985193] ami306_mod_init+ #####
<6>[ 3.988741] ami306_mod_init- #####
<3>[ 3.992300] vibrator_init:Couldn't get regulator vdd_vbrtr
<6>[ 3.997911] Loading pn544 driver
<7>[ 4.001332] gpio_request: gpio-184 (nfc_int) status -16
<6>[ 4.006857] PPP generic driver version 2.4.2
<6>[ 4.011315] PPP Deflate Compression module registered
<6>[ 4.016510] PPP BSD Compression module registered
<6>[ 4.023016] PPP MPPE Compression module registered
<6>[ 4.027959] NET: Registered protocol family 24
<6>[ 4.032521] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
<6>[ 4.040070] tun: Universal TUN/TAP device driver, 1.6
<6>[ 4.045211] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
<6>[ 4.051696] usbcore: registered new interface driver asix
<6>[ 4.057198] usbcore: registered new interface driver cdc_ether
<6>[ 4.063225] usbcore: registered new interface driver smsc95xx
<6>[ 4.069071] usbcore: registered new interface driver cdc_subset
<6>[ 4.075148] cdc_ncm: 23-Apr-2011
<6>[ 4.078480] usbcore: registered new interface driver cdc_ncm
<6>[ 4.084296] asuspec_init+ #####
<5>[ 4.087513] asuspec: [asuspec_init] cdev_alloc
<6>[ 4.092222] Wake9 for irq=370
<6>[ 4.095339] Wake9 for irq=370
<6>[ 4.098451] Enabling wake9
<6>[ 4.101232] gpio bank wake found: wake9 for irq=87
<6>[ 4.106086] Enabling wake9
<5>[ 4.108976] asuspec: [asuspec_send_ec_req] send EC_Request
<4>[ 4.114590] i2c-core: driver [asuspec] using legacy suspend method
<4>[ 4.120925] i2c-core: driver [asuspec] using legacy resume method
<6>[ 4.127190] asuspec_init- #####
<6>[ 4.130407] asusdec_init+ #####
<5>[ 4.133707] asusdec: [asusdec_init] cdev_alloc
<3>[ 4.138394] power_supply dock_battery: driver failed to report `status' property
<3>[ 4.145988] power_supply dock_battery: driver failed to report `status' property
<6>[ 4.153613] input: lid_input as /devices/platform/tegra-i2c.1/i2c-1/1-0019/input/input0
<6>[ 4.161867] Wake28 for irq=374
<6>[ 4.165025] Wake28 for irq=374
<6>[ 4.168222] Enabling wake28
<5>[ 4.171123] asusdec: [asusdec_irq_hall_sensor] LID open
<6>[ 4.176443] Wake29 for irq=375
<6>[ 4.179670] Wake29 for irq=375
<6>[ 4.182797] Enabling wake29
<4>[ 4.185722] i2c-core: driver [asusdec] using legacy suspend method
<5>[ 4.185746] asusdec: [asusdec_dock_init_work_function] TF201 dock-init
<5>[ 4.185755] asusdec: [asusdec_dock_init_work_function] No dock detected
<4>[ 4.205387] i2c-core: driver [asusdec] using legacy resume method
<6>[ 4.211651] asusdec_init- #####
<6>[ 4.214941] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 4.221588] tegra_ehci_probe+ #####
<3>[ 4.229324] Timed out waiting for lock bit on pll pll_u
<6>[ 4.234495] phy->instance= 2 , phy->xcvr_setup_value=61
<5>[ 4.240695] asusdec: [asusdec_lid_report_function] SW_LID report value = 0
<6>[ 4.242601] tegra-ehci tegra-ehci.2: Tegra EHCI Host Controller
<6>[ 4.242720] tegra-ehci tegra-ehci.2: new USB bus registered, assigned bus number 1
<5>[ 4.261403] asusdec: [asusdec_pad_battery_report_function] dock_in = 0, ret_val = -1
<4>[ 4.269287] audio_dock_in_out: global_audio_codec is NULL
<5>[ 4.274768] asusdec: [asusAudiodec_in_out_work_function] audio dock out
<6>[ 4.320699] tegra-ehci tegra-ehci.2: irq 129, io mem 0x7d008000
<6>[ 4.340690] tegra-ehci tegra-ehci.2: USB 2.0 started, EHCI 1.00
<6>[ 4.346738] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 4.353683] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 4.360984] usb usb1: Product: Tegra EHCI Host Controller
<6>[ 4.366525] usb usb1: Manufacturer: Linux 2.6.39.4-cyanogenmod-g80ca3c6 ehci_hcd
<6>[ 4.373997] usb usb1: SerialNumber: tegra-ehci.2
<6>[ 4.379036] hub 1-0:1.0: USB hub found
<6>[ 4.382918] hub 1-0:1.0: 1 port detected
<7>[ 4.387227] gpio_request: gpio-164 (DOCK_IN) status -16
<3>[ 4.392572] DOCK_IN GPIO164 request fault!-16
<6>[ 4.397032] gpio_dock_in_irq_init: request irq = 388, ret = 0
<6>[ 4.402963] tegra_ehci_probe- #####
<6>[ 4.406706] usbcore: registered new interface driver cdc_acm
<6>[ 4.412555] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
<6>[ 4.421217] usbcore: registered new interface driver cdc_wdm
<6>[ 4.427047] Initializing USB Mass Storage driver...
<6>[ 4.432104] usbcore: registered new interface driver usb-storage
<6>[ 4.438280] USB Mass Storage support registered.
<6>[ 4.443065] usbcore: registered new interface driver libusual
<6>[ 4.449076] usbcore: registered new interface driver usbserial
<6>[ 4.455047] USB Serial support registered for generic
<6>[ 4.460309] usbcore: registered new interface driver usbserial_generic
<6>[ 4.466942] usbserial: USB Serial Driver core
<6>[ 4.471507] USB Serial support registered for GSM modem (1-port)
<6>[ 4.477694] usbcore: registered new interface driver option
<5>[ 4.483451] asuspec: [asuspec_chip_init] Model Name: ASUS-TF201-PAD
<6>[ 4.489824] option: v0.7.2:USB Driver for GSM modems
<6>[ 4.495003] USB Serial support registered for pl2303
<5>[ 4.500061] asuspec: [asuspec_chip_init] EC-FW Version: PAD-EC20T-0216
<6>[ 4.506796] usbcore: registered new interface driver pl2303
<6>[ 4.512475] pl2303: Prolific PL2303 USB to serial adaptor driver
<6>[ 4.518682] USB Serial support registered for Qualcomm USB modem
<6>[ 4.524851] usbcore: registered new interface driver qcserial
<5>[ 4.530777] asuspec: [asuspec_chip_init] PCBA Version: TF201-PAD-SKU1
<6>[ 4.537302] NVidia Tegra High-Speed USB SOC Device Controller driver (Apr 20, 2007)
<7>[ 4.545135] gpio_request: gpio-164 (DOCK_IN) status -16
<3>[ 4.550533] DOCK_IN GPIO164 request fault!-16
<5>[ 4.554986] asuspec: [asuspec_enter_normal_mode] Entering normal mode
<6>[ 4.561601] gpio_limit_set1_irq_init: request irq = 285, ret = 0
<6>[ 4.567805] fsl_udc_probe()
<5>[ 4.570710] asuspec: [asuspec_work_function] 0x1 0x0 0xff 0xff
<6>[ 4.576805] phy->instance= 0 , phy->xcvr_setup_value=61
<3>[ 4.582298] fsl-tegra-udc fsl-tegra-udc: can't get charge regulator,err:-19
<6>[ 4.589463] tegra-otg tegra-otg: SUSPEND --> PERIPHERAL
<6>[ 4.594779] fsl_vbus_session, vbus_active=0, is_active=1
<6>[ 4.600360] android init
<3>[ 4.603191] pid != TF300TG, cancel acm ports
<3>[ 4.607535] pid != TF300TL, cancel serial ports
<4>[ 4.612572] Gadget Android: controller 'fsl-tegra-udc' not recognized
<6>[ 4.619088] android_usb gadget: android_usb ready
<6>[ 4.623965] fsl-tegra-udc: bind to driver android_usb
<7>[ 4.629214] gpio_set_debounce: gpio-168 status -22
<6>[ 4.634166] Wake24 for irq=392
<6>[ 4.637457] input: gpio-keys as /devices/platform/gpio-keys.0/input/input1
<6>[ 4.644481] gpio_keys: Reported pressed KEY_POWER
<6>[ 4.649266] gpio_keys: Released KEY_POWER
<6>[ 4.700842] Wake17 for irq=117
<6>[ 4.704170] input: tegra-kbc as /devices/platform/tegra-kbc/input/input2
<6>[ 4.711106] usbcore: registered new interface driver xpad
<6>[ 4.716647] mxt_init+ #####
<6>[ 4.719570] mxt_init- #####
<6>[ 4.722457] [elan] elan_ktf3k_ts_init
<6>[ 4.726269] elan-ktf3k 1-0010: [ELAN] Start HW reset!
<6>[ 4.790679] cable_detection_work_handler, vbus_active=0, is_active=1
<6>[ 4.797104] The USB cable is connected (0.5A)
<4>[ 4.810673] ========================================================
<4>[ 4.817096] battery_callback usb_cable_state =1
<4>[ 4.840670] ========================================================
<4>[ 4.847092] battery_callback battery driver not ready
<4>[ 4.852297] Touch charger state: 1
<7>[ 5.017939] [elan] GPIO_TP_INT_N=60
<6>[ 5.021511] elan-ktf3k 1-0010: The boot code is new!
<6>[ 5.767576] elan-ktf3k 1-0010: [elan] __hello_packet_handler: hello packet 55:55:55:55
<6>[ 5.775646] elan-ktf3k 1-0010: [elan] hello packet's rc = 0
<6>[ 5.970678] mpu_delay_init+ #####
<6>[ 5.974093] mpu_probe+ #####
<6>[ 5.977123] i2c i2c-2: mpu_probe: 0
<6>[ 5.991065] elan-ktf3k 1-0010: [elan] __fw_packet_handler: firmware version: 0x7053
<6>[ 5.999224] elan-ktf3k 1-0010: [elan] __fw_packet_handler: X resolution: 0x0000
<6>[ 6.006627] kxtf9_mod_delay_init+ #####
<6>[ 6.010970] elan-ktf3k 1-0010: [elan] __fw_packet_handler: Y resolution: 0x0000
<6>[ 6.018703] elan-ktf3k 1-0010: [elan] __fw_packet_handler: firmware id: 0x3024
<6>[ 6.026114] ami306_mod_delay_init+ #####
<6>[ 6.030183] elan-ktf3k 1-0010: [Elan] Max X=2944, Max Y=1856
<6>[ 6.036162] input: elan-touchscreen as /devices/virtual/input/input3
<4>[ 6.042776] /proc/ektf_dbg created
<6>[ 6.046622] elan-ktf3k 1-0010: [elan] Start touchscreen elan-touchscreen in interrupt mode
<4>[ 6.055070] [ELAN]misc_register finished!!
<6>[ 6.059171] elan-ktf3k 1-0010: Update power source to 2
<6>[ 6.067290] i2c i2c-2: Installing irq using 409
<6>[ 6.071923] i2c i2c-2: Module Param interface = mpuirq
<6>[ 6.077306] mpu_probe- #####
<6>[ 6.080288] i2c i2c-2: kxtf9_mod_probe: kxtf9
<6>[ 6.084809] i2c i2c-2: inv_mpu_register_slave: +kxtf9 Type 1: Addr: f IRQ: 341, Adapt: 2
<6>[ 6.093196] mpu_delay_init: Probe name mpu3050
<6>[ 6.097781] mpu_delay_init- #####
<6>[ 6.101185] kxtf9_init+ #####
<6>[ 6.112940] rtc_tps6591x rtc_tps6591x.0: RTC Time : 1/20/2000 15:38:11
<6>[ 6.120682] kxtf9_init- #####
<6>[ 6.123744] tps6591x 4-002d:
<6>[ 6.123747] getting alarm time::
<6>[ 6.130241] rtc_tps6591x rtc_tps6591x.0: RTC Time : 1/1/1900 0:0:0
<6>[ 6.136506] i2c i2c-2: Installing accelirq irq using 341
<6>[ 6.141972] Wake0 for irq=341
<6>[ 6.145131] i2c i2c-2: ami306_mod_probe: ami306
<6>[ 6.149742] i2c i2c-2: inv_mpu_register_slave: +ami306 Type 2: Addr: e IRQ: 400, Adapt: 2
<6>[ 6.158302] kxtf9_mod_delay_init: Probe name kxtf9_mod
<6>[ 6.163549] ami306_init+ #####
<6>[ 6.168698] rtc_tps6591x rtc_tps6591x.0: RTC Time : 1/20/2000 15:38:11
<6>[ 6.175537] using rtc device, rtc_tps6591x, for alarms
<6>[ 6.180661] rtc_tps6591x rtc_tps6591x.0: rtc core: registered rtc_tps6591x as rtc0
<6>[ 6.191722] rtc_tps6591x rtc_tps6591x.0: RTC Time : 1/20/2000 15:38:11
<6>[ 6.320823] i2c /dev entries driver
<6>[ 6.324749] Linux video capture interface: v2.00
<6>[ 6.329590] usbcore: registered new interface driver uvcvideo
<6>[ 6.335437] USB Video Class driver (v1.0.0)
<6>[ 6.339867] trpc_sema_init: registered misc dev 10:44
<6>[ 6.345900] trpc_node_register: Adding 'local' to node list
<6>[ 6.353611] nvavp nvavp: allocated IOVM at ff00000 for AVP os
<6>[ 6.359722] tegra_camera tegra_camera: tegra_camera_probe
<6>[ 6.365729] yuv fjm6mo sensor_init+ #####
<6>[ 6.659354] ami306_init- #####
<6>[ 6.662509] i2c i2c-2: Installing compassirq irq using 400
<6>[ 6.668289] yuv sensor_probe, compiled at Sep 14 2012 09:15:13
<4>[ 6.674272] yuv_sensor_power_on+
<6>[ 6.677584] gpio 143 set to 0
<6>[ 6.680756] ami306_mod_delay_init: Probe name ami306_mod
<6>[ 6.686140] ami306_mod_delay_init- #####
<7>[ 6.690154] gpio_request: gpio-143 (isp_power_1v2_en) status -16
<3>[ 6.696240] yuv_sensor_power_on_TF700T: gpio_request failed for gpio TF700T_ISP_POWER_1V2_EN_GPIO
<6>[ 6.705259] gpio 143 set to 1
<6>[ 6.708302] gpio 223 set to 0
<6>[ 6.711356] gpio 223 set to 1
<4>[ 6.731210] camera mclock on
<4>[ 6.734189] -tegra_camera_mclk_on_off
<6>[ 6.737922] gpio 216 set to 0
<6>[ 6.740976] gpio 216 set to 1
<4>[ 6.744089] yuv_sensor_power_on -
<6>[ 6.763793] fjm6mo check version number 0xb03400 1
<4>[ 6.768653] yuv_sensor_power_off+
<6>[ 6.772127] gpio 216 set to 0
<4>[ 6.775172] -tegra_camera_mclk_on_off
<6>[ 6.779054] gpio 223 set to 0
<6>[ 6.782181] gpio 143 set to 0
<4>[ 6.785218] yuv_sensor_power_off-
<6>[ 6.788647] yuv fjm6mo sensor_init- #####
<6>[ 6.792742] sensor_init+ #####
<6>[ 6.795965] yuv sensor_probe
<6>[ 6.799055] sensor_init- #####
<4>[ 6.802225] pad_probe: client->addr=b
<4>[ 6.806201] pad_get_psp: pad_device->battery_present=0
<3>[ 6.811427] pad-battery 4-000b: pad_get_psp: i2c read for 7 failed
<3>[ 6.817748] power_supply battery: driver failed to report `status' property
<4>[ 6.824821] pad_get_psp: pad_device->battery_present=0
<3>[ 6.830104] pad-battery 4-000b: pad_get_psp: i2c read for 7 failed
<6>[ 6.836560] pad-battery 4-000b: pad-battery: battery driver registered
<3>[ 6.843260] power_supply battery: driver failed to report `status' property
<6>[ 6.850394] Wake26 for irq=373
<6>[ 6.853654] The USB cable status = 1
<4>[ 6.857334] setup_irq: battery_present =1
<6>[ 6.861693] Wake25 for irq=372
<6>[ 6.864921] Wake25 for irq=372
<6>[ 6.868047] Enabling wake25
<4>[ 6.870921] setup_low_battery_irq:low_battery_present=0
<6>[ 6.876446] battery register misc device for I2C stress test rc=0
<4>[ 6.882663] i2c-core: driver [pad-battery] using legacy suspend method
<4>[ 6.889332] i2c-core: driver [pad-battery] using legacy resume method
<6>[ 6.895936] al3010_init+ #####
<4>[ 6.899064] light sensor info : al3010 init
<4>[ 6.903530] light sensor info : al3010 probe successed
<6>[ 6.908735] al3010 2-001c: driver version 1.0 enabled
<4>[ 6.914089] i2c-core: driver [al3010] using legacy suspend method
<4>[ 6.920253] i2c-core: driver [al3010] using legacy resume method
<6>[ 6.926438] al3010_init- #####
<6>[ 6.929657] device-mapper: uevent: version 1.0.3
<6>[ 6.934484] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected]
<6>[ 6.943020] Bluetooth: HCI UART driver ver 2.2
<6>[ 6.947611] Bluetooth: HCI H4 protocol initialized
<6>[ 6.952481] Bluetooth: HCILL protocol initialized
<6>[ 6.957257] Bluetooth: BlueSleep Mode Driver Ver 1.1
<6>[ 6.962371] bluesleep_init+ #####
<6>[ 6.965808] Wake7 for irq=390
<6>[ 6.968917] bluesleep_init- #####
<6>[ 6.972870] cpuidle: using governor ladder
<6>[ 6.977303] cpuidle: using governor menu
<6>[ 6.981343] sdhci: Secure Digital Host Controller Interface driver
<6>[ 6.987662] sdhci: Copyright(c) Pierre Ossman
<6>[ 6.992094] sdhci_drv_init+ #####
<6>[ 6.995621] [mmc]:tegra_sdhci_pltfm_init:914 mmc0: built_in 1
<6>[ 7.002232] sdhci sdhci-tegra.3: Error: tegra3 io dpd not supported for sdhci-tegra.3
<4>[ 7.011219] mmc0: Invalid maximum block size, assuming 512 bytes
<6>[ 7.017315] mmc0: no vmmc regulator found
<4>[ 7.021484] ========================================================
<6>[ 7.021588] tegra_usb_suspend+
<6>[ 7.021594] tegra->phy->instance=2
<6>[ 7.021599] tegra_usb_suspend: before ehci_halt
<6>[ 7.021606] tegra_usb_suspend: after ehci_halt, ret = 0
<6>[ 7.021625] tegra_usb_suspend-
<6>[ 7.050945] [mmc]:mmc_detect_change:1394 mmc0: gpio_69:0
<6>[ 7.056331] [mmc]:mmc_schedule_delayed_work:88 mmc0: delay 0
<6>[ 7.062156] mmc0: SDHCI controller on platform [sdhci-tegra.3] using ADMA
<6>[ 7.062167] [mmc]:mmc_rescan:1812 mmc0: gpio_69:0 rescan_disable 0
<4>[ 7.063289] docking_callback 1 docking_in =0 pu4=1
<4>[ 7.063294] ========================================================
<4>[ 7.063301] disable_irq(gpio_to_irq(TEGRA_GPIO_PS5)
<5>[ 7.063309] asusdec: [asusdec_pad_battery_report_function] dock_in = 0, ret_val = 0
<6>[ 7.099621] sdhci sdhci-tegra.2: Error: tegra3 io dpd not supported for sdhci-tegra.2
<4>[ 7.111980] mmc1: Invalid maximum block size, assuming 512 bytes
<6>[ 7.118087] mmc1: no vmmc regulator found
<4>[ 7.128944] mmc1 clock request: 101KHz. currently 48000KHz
<4>[ 7.139558] mmc1 clock request: 0KHz. currently 48000KHz
<6>[ 7.145039] [mmc]:mmc_detect_change:1394 mmc1: gpio_69:0
<6>[ 7.150422] [mmc]:mmc_schedule_delayed_work:88 mmc1: delay 0
<6>[ 7.156239] mmc1: SDHCI controller on platform [sdhci-tegra.2] using ADMA
<6>[ 7.156250] [mmc]:mmc_rescan:1812 mmc1: gpio_69:0 rescan_disable 0
<4>[ 7.157313] mmc1 clock request: 101KHz. currently 48000KHz
<4>[ 7.157330] mmc1 clock request: 0KHz. currently 48000KHz
<4>[ 7.170713] mmc1 clock request: 400KHz. currently 48000KHz
<6>[ 7.188085] Wake23 for irq=293
<6>[ 7.199411] Wake23 for irq=293
<6>[ 7.202540] Enabling wake23
<6>[ 7.205404] gpio bank wake found: wake23 for irq=66
<6>[ 7.210421] Enabling wake23
<6>[ 7.219353] [mmc]:tegra_sdhci_pltfm_init:869 mmc2: non-built_in 0
<6>[ 7.242402] [mmc]:mmc_decode_cid:111 cid.prv 0x6f
<6>[ 7.245879] sdhci sdhci-tegra.0: Error: tegra3 io dpd not supported for sdhci-tegra.0
<4>[ 7.246898] mmc2: Invalid maximum block size, assuming 512 bytes
<6>[ 7.246921] mmc2: no vmmc regulator found
<6>[ 7.247999] [mmc]:mmc_power_off:1242 mmc2:vdd_slot_reg: use_count 1
<6>[ 7.248007] [mmc]:mmc_power_off:1245 mmc2:vdd_io_reg: use_count 0
<6>[ 7.250232] [mmc]:mmc_detect_change:1394 mmc2: gpio_69:0
<6>[ 7.250239] [mmc]:mmc_schedule_delayed_work:88 mmc2: delay 0
<6>[ 7.250263] mmc2: SDHCI controller on platform [sdhci-tegra.0] using ADMA
<6>[ 7.250313] sdhci_drv_init- #####
<6>[ 7.251694] tegra-se tegra-se: tegra_se_probe: complete
<6>[ 7.252042] usbcore: registered new interface driver usbhid
<6>[ 7.252047] usbhid: USB HID core driver
<6>[ 7.252316] logger: created 256K log 'log_main'
<6>[ 7.252372] logger: created 256K log 'log_events'
<6>[ 7.252436] logger: created 256K log 'log_radio'
<6>[ 7.252494] logger: created 256K log 'log_system'
<6>[ 7.252633] RIL: [ril_init] RIL init
<3>[ 7.252640] RIL: [ril_init] Ril driver doesn't support this project
<4>[ 7.303421] mmc1 clock request: 0KHz. currently 48000KHz
<4>[ 7.304483] mmc1 clock request: 101KHz. currently 48000KHz
<4>[ 7.304499] mmc1 clock request: 0KHz. currently 48000KHz
<4>[ 7.320716] mmc1 clock request: 300KHz. currently 48000KHz
<6>[ 7.376947] [mmc]:mmc_read_ext_csd:259 ext_csd.sectors 0x3b34000 prod_name HYNIX BOOT_SIZE_MULTI 0x10
<4>[ 7.385331] mmc1 clock request: 0KHz. currently 48000KHz
<4>[ 7.386393] mmc1 clock request: 101KHz. currently 48000KHz
<4>[ 7.386412] mmc1 clock request: 0KHz. currently 48000KHz
<4>[ 7.400717] mmc1 clock request: 200KHz. currently 48000KHz
<4>[ 7.431478] mmc0: switch to bus width 1 ddr 0 failed
<3>[ 7.437548] mmc0: error -110 whilst initialising MMC card
<4>[ 7.485362] mmc1 clock request: 0KHz. currently 48000KHz
<4>[ 7.490840] mmc1 clock request: 101KHz. currently 48000KHz
<4>[ 7.498505] mmc1 clock request: 0KHz. currently 48000KHz
<4>[ 7.530738] mmc1 clock request: 101KHz. currently 48000KHz
<6>[ 7.574598] [mmc]:mmc_decode_cid:111 cid.prv 0x6f
<6>[ 7.605782] [mmc]:mmc_read_ext_csd:259 ext_csd.sectors 0x3b34000 prod_name HYNIX BOOT_SIZE_MULTI 0x10
<4>[ 7.618292] mmc1 clock request: 0KHz. currently 48000KHz
<6>[ 7.623699] [mmc]:mmc_rescan:1897 mmc1: extend_wakelock 0
<4>[ 7.648918] mmc0: switch to bus width 1 ddr 0 failed
<3>[ 7.655010] mmc0: error -110 whilst initialising MMC card
<6>[ 7.763997] [mmc]:mmc_decode_cid:111 cid.prv 0x6f
<6>[ 7.791113] [mmc]:mmc_read_ext_csd:259 ext_csd.sectors 0x3b34000 prod_name HYNIX BOOT_SIZE_MULTI 0x10
<4>[ 7.820391] mmc0: switch to bus width 1 ddr 0 failed
<3>[ 7.825463] mmc0: error -110 whilst initialising MMC card
<6>[ 7.851038] rt5631_modinit+ #####
<4>[ 7.854426] codec_3v3_power_switch_init
<7>[ 7.858335] gpio_request: gpio-120 (rt5631_3v3_power_control) status -16
<4>[ 7.865258] rt5631_3v3_power_control: request rt5631_3v3_power_control fail! : -16
<4>[ 7.873006] rt5631_i2c_probe+
<6>[ 7.876039] RT5631 Audio Codec 0.01 alsa 1.0.24
<4>[ 7.880763] rt5631_i2c_probe-
<6>[ 7.885966] rt5631_modinit- #####
<6>[ 7.895412] tegra_rt5631_modinit+ #####
<4>[ 7.901370] tegra_rt5631_modinit(): support codec rt5631
<4>[ 7.908875] tegra_rt5631_driver_probe+
<6>[ 7.977245] [mmc]:mmc_decode_cid:111 cid.prv 0x6f
<6>[ 8.006198] RT5631 initial ok!
<4>[ 8.009390] ************************realtek_ce_init_hwdep*************************************
<4>[ 8.018387] tegra_rt5631_init+
<3>[ 8.021977] rt5631 4-001a: asoc: failed to add dapm kcontrol AXO2MIX Mixer OUTVOLL Playback Switch: -16
<6>[ 8.031555] [mmc]:mmc_read_ext_csd:259 ext_csd.sectors 0x3b34000 prod_name HYNIX BOOT_SIZE_MULTI 0x10
<6>[ 8.047398] asoc: rt5631-hifi <-> tegra30-i2s.1 mapping ok
<6>[ 8.053672] asoc: dit-hifi <-> tegra30-spdif mapping ok
<4>[ 8.075286] mmc0: switch to bus width 1 ddr 0 failed
<3>[ 8.080416] mmc0: error -110 whilst initialising MMC card
<4>[ 8.086351] tegra_rt5631_driver_probe-
<6>[ 8.090290] tegra_rt5631_modinit- #####
<6>[ 8.094216] tegra_wm8903_modinit+ #####
<4>[ 8.098124] tegra_wm8903_modinit(): not support codec wm8903
<6>[ 8.106040] [mmc]:mmc_rescan:1897 mmc0: extend_wakelock 0
<6>[ 8.111527] [mmc]:mmc_rescan:1812 mmc2: gpio_69:0 rescan_disable 0
<6>[ 8.118922] headset_init+ #####
<4>[ 8.122150] HEADSET: Headset detection init
<4>[ 8.126556] HEADSET: Headset detection mode
<6>[ 8.130902] [mmc]:mmc_power_up:1194 mmc2:vdd_io_reg: use_count 0
<6>[ 8.136977] [mmc]:mmc_power_up:1197 mmc2:vdd_slot_reg: use_count 0
<4>[ 8.143308] HEADSET: Config Headset Button detection gpio
<7>[ 8.148776] gpio_request: gpio-186 (btn_INT) status -16
<4>[ 8.154196] HEADSET: Config Jack-in detection gpio
<4>[ 8.159337] HEADSET: Turn on micbias power
<6>[ 8.164461] Wake12 for irq=402
<6>[ 8.167672] Wake12 for irq=402
<6>[ 8.170798] Enabling wake12
<6>[ 8.173665] gpio bank wake found: wake12 for irq=119
<6>[ 8.178768] Enabling wake12
<4>[ 8.210202] HEADSET: Turn off micbias power
<4>[ 8.215869] HEADSET: Config LineOut detection gpio
<6>[ 8.222887] headset_init- #####
<6>[ 8.226124] fm34_init+ #####
<6>[ 8.229098] fm34_init()
<6>[ 8.231859] fm34: [fm34_chip_init] GPIO = 115 , state = 1
<6>[ 8.237332] fm34: [fm34_chip_init] GPIO = 222 , state = 1
<4>[ 8.381684] mmc2: host does not support reading read-only switch. assuming write-enable.
<6>[ 8.391975] mmc2: new high speed SD card at address 1234
<6>[ 8.397792] mmcblk0: mmc2:1234 SA02G 1.85 GiB
<6>[ 8.402593] fm34_probe()
<6>[ 8.405247] fm34_init- #####
<6>[ 8.408274] ALSA device list:
<6>[ 8.411348] fm34: [fm34_reconfig] ReConfigure DSP
<6>[ 8.416262] #0: HDA NVIDIA Tegra at 0x70038000 irq 113
<6>[ 8.421732] #1: tegra-codec
<6>[ 8.425025] oprofile: using arm/armv7-ca9
<6>[ 8.429224] GACT probability NOT on
<6>[ 8.432894] fm34: [fm34_reset_DSP] GPIO = 115 , state = 0
<6>[ 8.438366] fm34: [fm34_reset_DSP] GPIO = 115 , state = 1
<6>[ 8.444028] Mirror/redirect action on
<6>[ 8.447803] u32 classifier
<6>[ 8.450831] Actions configured
<6>[ 8.454349] Netfilter messages via NETLINK v0.30.
<6>[ 8.459281] mmcblk0: p1
<6>[ 8.462265] [mmc]:mmc_rescan_try_freq:1790 mmc2: SD completed
<6>[ 8.468163] [mmc]:mmc_rescan:1897 mmc2: extend_wakelock 1
<6>[ 8.473719] nf_conntrack version 0.5.0 (15611 buckets, 62444 max)
<6>[ 8.480262] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
<6>[ 8.487322] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>[ 8.493467] xt_time: kernel timezone is -0000
<6>[ 8.498066] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 8.503691] arp_tables: (C) 2002 David S. Miller
<6>[ 8.508429] TCP cubic registered
<6>[ 8.511845] NET: Registered protocol family 10
<6>[ 8.517359] Mobile IPv6
<6>[ 8.519907] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 8.525406] IPv6 over IPv4 tunneling driver
<6>[ 8.530619] NET: Registered protocol family 17
<6>[ 8.535179] NET: Registered protocol family 15
<6>[ 8.539806] Bluetooth: RFCOMM TTY layer initialized
<6>[ 8.544847] Bluetooth: RFCOMM socket layer initialized
<6>[ 8.550056] Bluetooth: RFCOMM ver 1.11
<6>[ 8.554026] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>[ 8.559411] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[ 8.565618] NET: Registered protocol family 37
<6>[ 8.570135] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
<5>[ 8.578087] Registering SWP/SWPB emulation handler
<6>[ 8.583243] fm34: [fm34_config_DSP] DSP ACK, read 0xc0: 1
<6>[ 8.588875] fm34: [fm34_config_DSP] Load TF201 DSP parameters
<4>[ 8.602196] Disabling clocks left on by bootloader:
<4>[ 8.607231] uarta
<4>[ 8.609506] fuse_burn
<4>[ 8.612210] cclk_lp
<4>[ 8.614649] pll_x_out0
<4>[ 8.617352] pll_d2_out0
<4>[ 8.620211] pll_p_out2
<4>[ 8.622924] pll_c_out1
<4>[ 8.625623] pll_m_out1
<6>[ 8.628422] CPU rate: 1150 MHz
<4>[ 8.632514] tegra3_dvfs: minimum cap.cbus rate 247000000 requires 1000 mV
<4>[ 8.639264] tegra3_dvfs: minimum cap.emc rate 400000000 requires 1000 mV
<6>[ 8.646242] tegra dvfs: tegra sysfs cap interface is initialized
<6>[ 8.652798] tegra_actmon.emc: Completed initialization (0)
<6>[ 8.658697] tegra_actmon.avp: Completed initialization (0)
<4>[ 8.665547] [DHD] ## wifi_probe
<4>[ 8.668841] [DHD] wifi_set_power = 1
<6>[ 8.790679] fm34: [fm34_config_DSP] config_length = 1497
<6>[ 8.796085] fm34: [fm34_config_DSP] DSP configuration is done
<4>[ 8.940685] tegra_watchdog_touch
<4>[ 8.944478] nct1008_get_temp: ret temp=27C
<4>[ 8.948923] Reg Status Reg 0x02 Value 0x80
<4>[ 8.954644] Reg Configuration Reg 0x03 Value 0x04
<4>[ 8.977295] [DHD] wifi_set_carddetect = 1
<6>[ 8.981487] [mmc]:mmc_detect_change:1394 mmc1: gpio_69:0
<6>[ 8.986867] [mmc]:mmc_schedule_delayed_work:88 mmc1: delay 0
<6>[ 8.992721] [mmc]:mmc_rescan:1812 mmc1: gpio_69:0 rescan_disable 0
<4>[ 8.992797] [DHD]
<4>[ 8.992800] Dongle Host Driver, version 5.90.125.94.1
<4>[ 8.992803] Compiled in drivers/net/wireless/bcmdhd on Sep 14 2012 at 09:15:57
<4>[ 9.014703] mmc1 clock request: 101KHz. currently 48000KHz
<4>[ 9.020296] mmc1 clock request: 0KHz. currently 48000KHz
<4>[ 9.040711] mmc1 clock request: 400KHz. currently 48000KHz
<4>[ 9.072807] mmc1 clock request: 50000KHz. currently 48000KHz
<6>[ 9.080855] mmc1: new high speed SDIO card at address 0001
<4>[ 9.087203] [DHD] bcmdhd: fw_path: /system/vendor/firmware/bcm4330/fw_bcmdhd.bin nvram_path: /system/etc/nvram_4330.txt
<4>[ 9.098272] [DHD] F1 signature read @0x18000000=0x16044330
<4>[ 9.104077] [DHD] sih->chiprev = 4
<4>[ 9.107618] [DHD] BCM4330B2 found!
<4>[ 9.114670] [DHD] DHD: dongle ram size is set to 294912(orig 294912)
<4>[ 9.121768] wl_create_event_handler thr:66 started
<4>[ 9.126832] dhd_attach thr:67 started
<4>[ 9.130631] dhd_attach thr:68 started
<4>[ 9.134545] dhd_attach thr:69 started
<4>[ 9.138992] [DHD] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
<4>[ 9.148044] [DHD] wifi_set_power = 0
<6>[ 9.156147] [mmc]:mmc_rescan_try_freq:1785 mmc1: sdio completed
<6>[ 9.162231] [mmc]:mmc_rescan:1897 mmc1: extend_wakelock 1
<4>[ 9.452007] [DHD] =========== WLAN placed in RESET ========
<6>[ 9.460044] rtc_tps6591x rtc_tps6591x.0: RTC Time : 1/20/2000 15:38:14
<6>[ 9.466699] rtc_tps6591x rtc_tps6591x.0: setting system clock to 2000-01-20 15:38:14 UTC (948382694)
<6>[ 9.476450] Freeing init memory: 232K
<3>[ 9.483133] init: /init.rc: 40: invalid option ' disabled'
<4>[ 9.499157] pad_get_psp val->intval=Full ret=e0
<4>[ 9.516425] pad_get_psp voltage_now =8222
<4>[ 9.523117] pad_get_capacity val->intval=100 ret=100
<4>[ 9.530984] pad_get_psp batttery temperature=214
<3>[ 9.538905] power_supply dock_battery: driver failed to report `status' property
<5>[ 10.537066] asuspec: [asuspec_enter_s3_work_function] EC in S3
<6>[ 12.070678] charger_pad_dock_detection:0 dock_in_value=1 charger_pad_dock_value =0
<5>[ 12.270718] asuspec: [asuspec_send_ec_req] send EC_Request
<4>[ 12.276358] battery_status_poll 120 1
<5>[ 12.344354] asuspec: [asuspec_work_function] 0x2 0x81 0x50 0xff
<5>[ 12.350417] asuspec: [asuspec_smi] ASUSPEC_SMI_HANDSHAKING
<4>[ 12.543902] pad_get_psp val->intval=Full ret=e0
<4>[ 12.561136] pad_get_psp voltage_now =8236
<4>[ 12.568054] pad_get_capacity val->intval=100 ret=100
<4>[ 12.576090] pad_get_psp batttery temperature=214
<5>[ 13.577972] asuspec: [asuspec_enter_s3_work_function] EC in S3
<4>[ 13.960684] tegra_watchdog_touch
<4>[ 13.964553] nct1008_get_temp: ret temp=27C
<4>[ 13.969061] Reg Status Reg 0x02 Value 0x80
<4>[ 13.974726] Reg Configuration Reg 0x03 Value 0x04
<3>[ 14.015807] init: Unable to open persistent property directory /data/property errno: 2
<3>[ 14.026231] android_usb: already disabled
<6>[ 14.029719] warning: `adbd' uses 32-bit capabilities (legacy support in use)
<6>[ 14.029857] adb_open(adbd)
<6>[ 14.040886] adb_bind_config
<3>[ 14.041028] init: using deprecated syntax for specifying property 'ro.serialno', use ${name} instead
<6>[ 14.041331] adb_bind_config
<6>[ 14.041375] adb_release
<6>[ 14.042658] adb_open(adbd)
<4>[ 14.077748] Check cardhu_panel_disable in TF202
<6>[ 14.186501] android_work: did not send uevent (0 0 (null))
<4>[ 14.201093] Disp: diff_msec= 123
<6>[ 14.343013] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 14.346658] android_work: sent uevent USB_STATE=DISCONNECTED
<6>[ 14.544938] android_work: sent uevent USB_STATE=CONNECTED
<4>[ 15.090773] Check cardhu_panel_enable
<4>[ 15.090782] Check panel is panasonic
<4>[ 15.120686] Check power on/off for bridge IC
<4>[ 15.120693] Check enable TF301_1.8V
<4>[ 15.130708] Check enable TF301_I2C_Switch
<4>[ 15.140724] Check enable TF301_OSC
<4>[ 15.161105] Check tegra_dc_rgb_enable
<4>[ 15.161111] Check set polarity
<4>[ 15.161815] Check Chip ID=44
<4>[ 15.161819] Check RevID=0
<6>[ 15.161824] DISPLAY_write_table display_write_table
<4>[ 15.235429] ========================
<4>[ 15.235434] ========================
<4>[ 15.235439] Check start to read register
<4>[ 15.235444] Panel is panasonic
<6>[ 15.919934] set_config : usb set config wake lock ++
<6>[ 15.925263] android_usb gadget: high speed config #1: android
<6>[ 15.931323] android_work: sent uevent USB_STATE=CONFIGURED
<4>[ 18.980699] tegra_watchdog_touch
<4>[ 18.984603] nct1008_get_temp: ret temp=27C
<4>[ 18.989046] Reg Status Reg 0x02 Value 0x80
<4>[ 18.994716] Reg Configuration Reg 0x03 Value 0x04
<4>[ 20.275711] adbd (124): /proc/124/oom_adj is deprecated, please use /proc/124/oom_score_adj instead.
<4>[ 24.000697] tegra_watchdog_touch
<4>[ 24.004523] nct1008_get_temp: ret temp=27C
<4>[ 24.008970] Reg Status Reg 0x02 Value 0x80
<4>[ 24.014715] Reg Configuration Reg 0x03 Value 0x04
<4>[ 29.020714] tegra_watchdog_touch
<4>[ 29.024695] nct1008_get_temp: ret temp=27C
<4>[ 29.029142] Reg Status Reg 0x02 Value 0x80
<4>[ 29.034817] Reg Configuration Reg 0x03 Value 0x04
<4>[ 34.040701] tegra_watchdog_touch
<4>[ 34.044545] nct1008_get_temp: ret temp=27C
<4>[ 34.048991] Reg Status Reg 0x02 Value 0x80
<4>[ 34.054678] Reg Configuration Reg 0x03 Value 0x04
<4>[ 39.060694] tegra_watchdog_touch
<4>[ 39.064593] nct1008_get_temp: ret temp=27C
<4>[ 39.069044] Reg Status Reg 0x02 Value 0x80
<4>[ 39.074788] Reg Configuration Reg 0x03 Value 0x04
<4>[ 44.080698] tegra_watchdog_touch
<4>[ 44.084517] nct1008_get_temp: ret temp=28C
<4>[ 44.089027] Reg Status Reg 0x02 Value 0x80
<4>[ 44.094696] Reg Configuration Reg 0x03 Value 0x04
<4>[ 49.100696] tegra_watchdog_touch
<4>[ 49.104519] nct1008_get_temp: ret temp=28C
<4>[ 49.108954] Reg Status Reg 0x02 Value 0x80
<4>[ 49.114720] Reg Configuration Reg 0x03 Value 0x04
<4>[ 54.120690] tegra_watchdog_touch
<4>[ 54.124585] nct1008_get_temp: ret temp=28C
<4>[ 54.129018] Reg Status Reg 0x02 Value 0x00
<4>[ 54.134709] Reg Configuration Reg 0x03 Value 0x04
<4>[ 59.140691] tegra_watchdog_touch
<4>[ 59.144511] nct1008_get_temp: ret temp=28C
<4>[ 59.149021] Reg Status Reg 0x02 Value 0x80
<4>[ 59.154710] Reg Configuration Reg 0x03 Value 0x04
<4>[ 64.160705] tegra_watchdog_touch
<4>[ 64.164619] nct1008_get_temp: ret temp=28C
<4>[ 64.169057] Reg Status Reg 0x02 Value 0x80
<4>[ 64.174818] Reg Configuration Reg 0x03 Value 0x04
<4>[ 69.180702] tegra_watchdog_touch
<4>[ 69.184526] nct1008_get_temp: ret temp=28C
<4>[ 69.189034] Reg Status Reg 0x02 Value 0x00
<4>[ 69.194725] Reg Configuration Reg 0x03 Value 0x04
<4>[ 74.200693] tegra_watchdog_touch
<4>[ 74.204512] nct1008_get_temp: ret temp=28C
<4>[ 74.208948] Reg Status Reg 0x02 Value 0x80
<4>[ 74.214709] Reg Configuration Reg 0x03 Value 0x04
<4>[ 79.220694] tegra_watchdog_touch
<4>[ 79.224584] nct1008_get_temp: ret temp=28C
<4>[ 79.229018] Reg Status Reg 0x02 Value 0x80
<4>[ 79.234689] Reg Configuration Reg 0x03 Value 0x04
<4>[ 84.240690] tegra_watchdog_touch
<4>[ 84.244515] nct1008_get_temp: ret temp=28C
<4>[ 84.249021] Reg Status Reg 0x02 Value 0x80
<4>[ 84.254689] Reg Configuration Reg 0x03 Value 0x04
<4>[ 89.260686] tegra_watchdog_touch
<4>[ 89.264638] nct1008_get_temp: ret temp=28C
<4>[ 89.269080] Reg Status Reg 0x02 Value 0x80
<4>[ 89.274819] Reg Configuration Reg 0x03 Value 0x04
<4>[ 94.280705] tegra_watchdog_touch
<4>[ 94.284546] nct1008_get_temp: ret temp=28C
<4>[ 94.289055] Reg Status Reg 0x02 Value 0x80
<4>[ 94.294723] Reg Configuration Reg 0x03 Value 0x04
<4>[ 99.300695] tegra_watchdog_touch
<4>[ 99.304530] nct1008_get_temp: ret temp=28C
<4>[ 99.308965] Reg Status Reg 0x02 Value 0x80
<4>[ 99.314703] Reg Configuration Reg 0x03 Value 0x04
<4>[ 104.320698] tegra_watchdog_touch
<4>[ 104.324600] nct1008_get_temp: ret temp=29C
<4>[ 104.329036] Reg Status Reg 0x02 Value 0x80
<4>[ 104.334707] Reg Configuration Reg 0x03 Value 0x04
<4>[ 109.340700] tegra_watchdog_touch
<4>[ 109.344527] nct1008_get_temp: ret temp=29C
<4>[ 109.349033] Reg Status Reg 0x02 Value 0x80
<4>[ 109.354699] Reg Configuration Reg 0x03 Value 0x04
<4>[ 114.360693] tegra_watchdog_touch
<4>[ 114.364599] nct1008_get_temp: ret temp=29C
<4>[ 114.369034] Reg Status Reg 0x02 Value 0x00
<4>[ 114.374777] Reg Configuration Reg 0x03 Value 0x04
<4>[ 119.380693] tegra_watchdog_touch
<4>[ 119.384509] nct1008_get_temp: ret temp=29C
<4>[ 119.389021] Reg Status Reg 0x02 Value 0x80
<4>[ 119.394693] Reg Configuration Reg 0x03 Value 0x04
<4>[ 124.400916] tegra_watchdog_touch
<4>[ 124.404853] nct1008_get_temp: ret temp=29C
<4>[ 124.409357] Reg Status Reg 0x02 Value 0x80
<4>[ 124.415093] Reg Configuration Reg 0x03 Value 0x04
<4>[ 129.420692] tegra_watchdog_touch
<4>[ 129.424584] nct1008_get_temp: ret temp=29C
<4>[ 129.429032] Reg Status Reg 0x02 Value 0x80
<4>[ 129.434704] Reg Configuration Reg 0x03 Value 0x04
<5>[ 132.330755] asuspec: [asuspec_send_ec_req] send EC_Request
<4>[ 132.336326] battery_status_poll 120 1
<5>[ 132.401897] asuspec: [asuspec_work_function] 0x2 0x81 0x50 0xff
<5>[ 132.407886] asuspec: [asuspec_smi] ASUSPEC_SMI_HANDSHAKING
<4>[ 132.603893] pad_get_psp val->intval=Full ret=e0
<4>[ 132.622667] pad_get_psp voltage_now =8221
<4>[ 132.629409] pad_get_capacity val->intval=100 ret=99
<4>[ 132.637320] pad_get_psp batttery temperature=226
<5>[ 133.636430] asuspec: [asuspec_enter_s3_work_function] EC in S3
<4>[ 134.440693] tegra_watchdog_touch
<4>[ 134.444513] nct1008_get_temp: ret temp=29C
<4>[ 134.448960] Reg Status Reg 0x02 Value 0x80
<4>[ 134.454703] Reg Configuration Reg 0x03 Value 0x04
<4>[ 139.460690] tegra_watchdog_touch
<4>[ 139.464642] nct1008_get_temp: ret temp=29C
<4>[ 139.469104] Reg Status Reg 0x02 Value 0x00
<4>[ 139.474843] Reg Configuration Reg 0x03 Value 0x04
<4>[ 144.480690] tegra_watchdog_touch
<4>[ 144.484514] nct1008_get_temp: ret temp=29C
<4>[ 144.489019] Reg Status Reg 0x02 Value 0x80
<4>[ 144.494693] Reg Configuration Reg 0x03 Value 0x04
<4>[ 149.500692] tegra_watchdog_touch
<4>[ 149.504510] nct1008_get_temp: ret temp=29C
<4>[ 149.508946] Reg Status Reg 0x02 Value 0x80
<4>[ 149.514703] Reg Configuration Reg 0x03 Value 0x04
<4>[ 154.520687] tegra_watchdog_touch
<4>[ 154.524617] nct1008_get_temp: ret temp=29C
<4>[ 154.529051] Reg Status Reg 0x02 Value 0x80
<4>[ 154.534736] Reg Configuration Reg 0x03 Value 0x04
<4>[ 159.540702] tegra_watchdog_touch
<4>[ 159.544536] nct1008_get_temp: ret temp=29C
<4>[ 159.548974] Reg Status Reg 0x02 Value 0x80
<4>[ 159.554740] Reg Configuration Reg 0x03 Value 0x04
<4>[ 164.560693] tegra_watchdog_touch
<4>[ 164.564581] nct1008_get_temp: ret temp=29C
<4>[ 164.569015] Reg Status Reg 0x02 Value 0x00
<4>[ 164.574779] Reg Configuration Reg 0x03 Value 0x04
<4>[ 169.580688] tegra_watchdog_touch
<4>[ 169.584549] nct1008_get_temp: ret temp=29C
<4>[ 169.589057] Reg Status Reg 0x02 Value 0x80
<4>[ 169.594742] Reg Configuration Reg 0x03 Value 0x04
<4>[ 174.600693] tegra_watchdog_touch
<4>[ 174.604512] nct1008_get_temp: ret temp=29C
<4>[ 174.608946] Reg Status Reg 0x02 Value 0x00
<4>[ 174.614712] Reg Configuration Reg 0x03 Value 0x04
<4>[ 179.620693] tegra_watchdog_touch
<4>[ 179.624583] nct1008_get_temp: ret temp=29C
<4>[ 179.629018] Reg Status Reg 0x02 Value 0x80
<4>[ 179.634682] Reg Configuration Reg 0x03 Value 0x04
<4>[ 184.640687] tegra_watchdog_touch
<4>[ 184.644574] nct1008_get_temp: ret temp=29C
<4>[ 184.649017] Reg Status Reg 0x02 Value 0x80
<4>[ 184.654760] Reg Configuration Reg 0x03 Value 0x04
<4>[ 189.660701] tegra_watchdog_touch
<4>[ 189.664592] nct1008_get_temp: ret temp=29C
<4>[ 189.669027] Reg Status Reg 0x02 Value 0x80
<4>[ 189.674773] Reg Configuration Reg 0x03 Value 0x04
<4>[ 194.680693] tegra_watchdog_touch
<4>[ 194.684510] nct1008_get_temp: ret temp=29C
<4>[ 194.689016] Reg Status Reg 0x02 Value 0x80
<4>[ 194.694688] Reg Configuration Reg 0x03 Value 0x04
<4>[ 199.700689] tegra_watchdog_touch
<4>[ 199.704596] nct1008_get_temp: ret temp=29C
<4>[ 199.709039] Reg Status Reg 0x02 Value 0x80
<4>[ 199.714785] Reg Configuration Reg 0x03 Value 0x04
<4>[ 204.720696] tegra_watchdog_touch
<4>[ 204.724594] nct1008_get_temp: ret temp=30C
<4>[ 204.729030] Reg Status Reg 0x02 Value 0x80
<4>[ 204.734696] Reg Configuration Reg 0x03 Value 0x04
<4>[ 209.740695] tegra_watchdog_touch
<4>[ 209.744521] nct1008_get_temp: ret temp=30C
<4>[ 209.748956] Reg Status Reg 0x02 Value 0x80
<4>[ 209.754701] Reg Configuration Reg 0x03 Value 0x04
<4>[ 214.760691] tegra_watchdog_touch
<4>[ 214.764675] nct1008_get_temp: ret temp=30C
<4>[ 214.769116] Reg Status Reg 0x02 Value 0x80
<4>[ 214.774855] Reg Configuration Reg 0x03 Value 0x04
<4>[ 219.780703] tegra_watchdog_touch
<4>[ 219.784523] nct1008_get_temp: ret temp=30C
<4>[ 219.789035] Reg Status Reg 0x02 Value 0x80
<4>[ 219.794703] Reg Configuration Reg 0x03 Value 0x04
<4>[ 224.800693] tegra_watchdog_touch
<4>[ 224.804508] nct1008_get_temp: ret temp=30C
<4>[ 224.808950] Reg Status Reg 0x02 Value 0x80
<4>[ 224.814694] Reg Configuration Reg 0x03 Value 0x04
<4>[ 229.820764] tegra_watchdog_touch
<4>[ 229.824698] nct1008_get_temp: ret temp=30C
<4>[ 229.829153] Reg Status Reg 0x02 Value 0x00
<4>[ 229.834818] Reg Configuration Reg 0x03 Value 0x04
<4>[ 234.840698] tegra_watchdog_touch
<4>[ 234.844517] nct1008_get_temp: ret temp=30C
<4>[ 234.848962] Reg Status Reg 0x02 Value 0x80
<4>[ 234.854635] Reg Configuration Reg 0x03 Value 0x04
<4>[ 239.860691] tegra_watchdog_touch
<4>[ 239.864580] nct1008_get_temp: ret temp=30C
<4>[ 239.869023] Reg Status Reg 0x02 Value 0x00
<4>[ 239.874766] Reg Configuration Reg 0x03 Value 0x04
<3>[ 240.640722] INFO: task kinteractiveup:81 blocked for more than 120 seconds.
<3>[ 240.647828] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 240.655736] kinteractiveup D c0571c3c 0 81 2 0x00000000
<4>[ 240.662465] [<c0571c3c>] (schedule+0x87c/0x958) from [<c00a480c>] (kthread+0x64/0x84)
<4>[ 240.670481] [<c00a480c>] (kthread+0x64/0x84) from [<c00482b8>] (kernel_thread_exit+0x0/0x8)
_that said:
Also try this:
Code:
adb shell hexdump -C -s 0x380000 -n 8 /dev/block/mmcblk0
and tell me if it outputs "ANDROID!" (after some hexadecimal numbers).
Click to expand...
Click to collapse
No, it only outputs:
*
00380000
I followed below steps for installing official miui v4 rom to desire s
1. Download official miui v4 stable rom from www.miui.com
2. Format sd card and system (clean format).
3. Hboot is 7.0
4. Installed official chinese sense 3.6 rom and reboot the phone to recovery.
5. factory reset and wipe cache & delvic cache.
My problem is while installing miui v4 3.2.22 stable official version...my installation aborted saying
updating package....
formatting system.......
do not format system.............
installed successfully....
Post reboot HTC splash screen appears for a while and then phone reboots on its own to recovery.
Please help...
talktoraj83 said:
I followed below steps for installing official miui v4 rom to desire s
1. Download official miui v4 stable rom from www.miui.com
2. Format sd card and system (clean format).
3. Hboot is 7.0
4. Installed official chinese sense 3.6 rom and reboot the phone to recovery.
5. factory reset and wipe cache & delvic cache.
My problem is while installing miui v4 3.2.22 stable official version...my installation aborted saying
updating package....
formatting system.......
do not format system.............
installed successfully....
Post reboot HTC splash screen appears for a while and then phone reboots on its own to recovery.
Please help...
Click to expand...
Click to collapse
Flash the boot.img from the ROM.zip through cmd on your PC.
NVardan said:
Flash the boot.img from the ROM.zip through cmd on your PC.
Click to expand...
Click to collapse
But he's on hboot 7.xxx
Shouldn't he be alrd s-off. Op do tell us if you're s-on or off.
Get 4ext. I think there's an image file that u can flash in fastboot mode. Search dev section for the thread.
Wipe everything (except sdcard)
Flash ROM
Reboot into rom
*flash gapps after set up.
FromBeyondThisWorld
#Fear said:
But he's on hboot 7.xxx
Shouldn't he be alrd s-off. Op do tell us if you're s-on or off.
Get 4ext. I think there's an image file that u can flash in fastboot mode. Search dev section for the thread.
Wipe everything (except sdcard)
Flash ROM
Reboot into rom
*flash gapps after set up.
FromBeyondThisWorld
Click to expand...
Click to collapse
You're right. That makes sense. HBOOT 7.xxx is already S-Off (I'm on this hboot too, I didn't notice ). :silly:
#Fear said:
But he's on hboot 7.xxx
Shouldn't he be alrd s-off. Op do tell us if you're s-on or off.
Get 4ext. I think there's an image file that u can flash in fastboot mode. Search dev section for the thread.
Wipe everything (except sdcard)
Flash ROM
Reboot into rom
*flash gapps after set up.
FromBeyondThisWorld
Click to expand...
Click to collapse
Ya my phone is s-off....and had pushed boot.img successfully bufore and after installation of rom.zip file but still same problem..
I think m missing some step....that is specific for flashing miui v4 official rom for desire s
What recovery is on your device? Try using 4ext :thumbup:
1.full wipe(except sdcard)
2.flash rom
3.reboot
Don't flash gapps first and see if it boots.
FromBeyondThisWorld
#Fear said:
What recovery is on your device? Try using 4ext :thumbup:
1.full wipe(except sdcard)
2.flash rom
3.reboot
Don't flash gapps first and see if it boots.
FromBeyondThisWorld
Click to expand...
Click to collapse
No its not booting..i have tried all permutation & combination....
on latest 4ext recovery
talktoraj83 said:
No its not booting..i have tried all permutation & combination....
on latest 4ext recovery
Click to expand...
Click to collapse
There is one hint if it could help some one to find out issue with my installation...
When m trying below patch for formatting my phone gives error..
http://www.androidfilehost.com/?fid=9390189810980749321
talktoraj83 said:
There is one hint if it could help some one to find out issue with my installation...
When m trying below patch for formatting my phone gives error..
http://www.androidfilehost.com/?fid=9390189810980749321
Click to expand...
Click to collapse
This guy had bootloop too when he tried, but he was trying the russian version. He solve it with amidabuddha kernel.
Cheers
#Fear said:
This guy had bootloop too when he tried, but he was trying the russian version. He solve it with amidabuddha kernel.
Cheers
Click to expand...
Click to collapse
Can you confirm that miuiv4 official version rom has kernel inside it or not?
talktoraj83 said:
Can you confirm that miuiv4 official version rom has kernel inside it or not?
Click to expand...
Click to collapse
Just look inside the zip and you`ll know....
Flashing another kernel wouldn`t harm,
if your device isn`t booting anyway...
take a logcat and attach it and/or look inside,
then all`ll become clear...
asgardr said:
Just look inside the zip and you`ll know....
Flashing another kernel wouldn`t harm,
if your device isn`t booting anyway...
take a logcat and attach it and/or look inside,
then all`ll become clear...
Click to expand...
Click to collapse
Please find below logcat-
10.554687] init: untracked pid 1288 exited
<6>[ 10.666137] EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts:
<3>[ 10.779083] EXT3-fs (mmcblk0p25): error: couldn't mount because of unsupported optional features (40)
<3>[ 10.779937] EXT2-fs (mmcblk0p25): error: couldn't mount because of unsupported optional features (40)
<6>[ 10.828582] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts: (null)
<3>[ 10.829498] init: untracked pid 1309 exited
<6>[ 11.487731] pm8058_led_currents_store: bank 6 currents 1
<6>[ 11.487976] pm8058_drvx_led_brightness_set: bank 6 brightness 0
<6>[ 11.488128] pm8058_drvx_led_brightness_set: bank 6 brightness 255
<6>[ 11.488708] pm8058_led_currents_store: bank 6 currents 9
<6>[ 11.488830] pm8058_drvx_led_brightness_set: bank 6 brightness 0
<6>[ 11.489074] pm8058_drvx_led_brightness_set: bank 6 brightness 255
<6>[ 11.490509] pm8058_drvx_led_brightness_set: bank 6 brightness 9
<6>[ 11.491119] pm8058_drvx_led_brightness_set: bank 6 brightness 90
<6>[ 11.491638] pm8058_drvx_led_brightness_set: bank 6 brightness 9
<6>[ 11.492218] pm8058_drvx_led_brightness_set: bank 6 brightness 90
<3>[ 11.875061] init: untracked pid 1343 exited
<6>[ 17.498992] [email protected],236
<6>[ 17.559783] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 17.561279] [ATS][set_vibration][successful]
<6>[ 17.584899] [VIB]vibrator_timer_func
<6>[ 17.663330] [email protected],236
<6>[ 25.172546] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 25.173919] [ATS][set_vibration][successful]
<6>[ 25.197753] [VIB]vibrator_timer_func
<6>[ 34.992889] [BATT] M2A_RPC: set_charging: 0 at 29234003670 (2013-08-30 18:23:52.340426829 UTC)
<6>[ 34.993194] Switch charger OFF
<6>[ 34.994964] [BATT] M2A_RPC: set_charging: 1 at 29236046353 (2013-08-30 18:23:52.342500000 UTC)
<6>[ 34.995269] Switch charger ON (SLOW)
<6>[ 34.996215] batt: Switch charger ON (SLOW): regh 0x03=83
<6>[ 34.997314] [BATT] M2A_RPC: cable_update: USB at 29238332939 (2013-08-30 18:23:52.344847561 UTC)
<6>[ 34.997619] [BATT] htc_cable_status_update: 0 -> 1
<6>[ 34.997741] [USB] msm_hsusb_set_vbus_state: 1
<6>[ 34.997924] [USB] hsusb: OFFLINE -> ONLINE
<6>[ 34.998016] [USB] lpm exit
<6>[ 34.999298] [USB] hsusb: reset controller
<6>[ 35.044311] msm_hsusb_phy_reset
<6>[ 35.189300] [USB] ulpi: write 0x06 to 0x36
<6>[ 35.189392] [USB] ulpi: write 0x0c to 0x31
<6>[ 35.189605] [USB] ulpi: write 0x31 to 0x32
<6>[ 35.189697] [USB] ulpi: write 0x01 to 0x0d
<6>[ 35.189788] [USB] ulpi: write 0x01 to 0x10
<6>[ 35.189971] [USB] handle_notify_offline: notify offline
<6>[ 35.190093] [USB] msm_hsusb: enable pullup
<6>[ 35.193206] [USB] suspend
<6>[ 35.209381] [USB] not AC charger
<6>[ 35.293640] [USB] reset
<6>[ 35.293731] [USB] send connect type 1
<6>[ 35.293853] Touch: cable change to 1
<6>[ 35.295227] fsg_set_ums_state: 1
<6>[ 35.295349] ums: set state 1
<6>[ 35.295745] [BATT] online=1
<6>[ 35.295928] [USB] portchange USB_SPEED_HIGH
<6>[ 35.296112] [BATT] Update SMEM: cable type 1 at 29536839037 (2013-08-30 18:23:52.643353659 UTC)
<6>[ 35.338897] pm8058_pwm_led_brightness_set: bank 0 brightness 0
<6>[ 35.345031] pm8058_pwm_led_brightness_set: bank 1 brightness 1
<6>[ 35.351470] pm8058_pwm_led_brightness_set: bank 0 brightness 0
<6>[ 35.357391] pm8058_pwm_led_brightness_set: bank 1 brightness 1
<6>[ 35.484069] android_usb gadget: high speed config #1: android
<6>[ 35.484222] adb_function_set_alt: maxsize = 512
<6>[ 35.484497] ums: set state 1
<6>[ 66.039398] Release 'boot-time' perf_lock
<6>[ 66.620391] Release 'boot-time' no_halt_lock
<6>[ 67.040405] perflock_notifier_call: cpufreq recover policy 245760 1024000
<6>[ 246.697113] [BATT] M2A_RPC: level_update: 68 at 240732143916 (2013-08-30 18:27:23.838079269 UTC)
<6>[ 246.698181] [BATT] power_supply_changed: battery at 240732906111 (2013-08-30 18:27:23.839176830 UTC)
<6>[ 246.718322] pm8058_pwm_led_brightness_set: bank 0 brightness 0
<6>[ 246.737548] pm8058_pwm_led_brightness_set: bank 1 brightness 1
<3>[ 246.935974] INFO: task audio_mvs:428 blocked for more than 120 seconds.
<3>[ 246.936370] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 246.937011] audio_mvs D c0425f80 0 428 2 0x00000000
<4>[ 246.938323] Backtrace:
<4>[ 246.939056] [<c0425bbc>] (schedule+0x0/0x450) from [<c005101c>] (__msm_rpc_read+0x22c/0xa4c)
<4>[ 246.939758] [<c0050df0>] (__msm_rpc_read+0x0/0xa4c) from [<c0051858>] (msm_rpc_read+0x1c/0x88)
<4>[ 246.940185] [<c005183c>] (msm_rpc_read+0x0/0x88) from [<c0074f34>] (audio_mvs_thread+0x4c/0x164)
<4>[ 246.940856] r6:00000000 r5:c7e69f9c r4:c05ef368
<4>[ 246.942596] [<c0074ee8>] (audio_mvs_thread+0x0/0x164) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 246.942962] r8:00000000 r7:c05ef368 r6:c0074ee8 r5:c7e69fcc r4:c7c1df48
<4>[ 246.945312] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 246.946044] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df48
<3>[ 246.947753] INFO: task krmt_storagecln:460 blocked for more than 120 seconds.
<3>[ 246.948425] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 246.948791] krmt_storagecln D c0425f80 0 460 2 0x00000000
<4>[ 246.950073] Backtrace:
<4>[ 246.950805] [<c0425bbc>] (schedule+0x0/0x450) from [<c004a1c4>] (rpc_clients_cb_thread+0x98/0x1b0)
<4>[ 246.951507] [<c004a12c>] (rpc_clients_cb_thread+0x0/0x1b0) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 246.952239] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 246.952606] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1ddf8
<3>[ 246.954620] INFO: task voice:740 blocked for more than 120 seconds.
<3>[ 246.955261] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 246.955657] voice D c0425f80 0 740 2 0x00000000
<4>[ 246.957031] Backtrace:
<4>[ 246.957763] [<c0425bbc>] (schedule+0x0/0x450) from [<c04266e8>] (schedule_timeout+0x24/0x23c)
<4>[ 246.958465] [<c04266c4>] (schedule_timeout+0x0/0x23c) from [<c04264e0>] (wait_for_common+0x12c/0x1f0)
<4>[ 246.959136] r7:c76f2000 r6:00000002 r5:c05eaf44 r4:7fffffff
<4>[ 246.960876] [<c04263b4>] (wait_for_common+0x0/0x1f0) from [<c0426684>] (wait_for_completion+0x1c/0x20)
<4>[ 246.961578] [<c0426668>] (wait_for_completion+0x0/0x20) from [<c005a38c>] (voice_thread+0x6c/0x554)
<4>[ 246.962280] [<c005a320>] (voice_thread+0x0/0x554) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 246.962707] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 246.963378] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df30
<3>[ 367.073181] INFO: task rpcrouter:274 blocked for more than 120 seconds.
<3>[ 367.073547] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 367.074249] rpcrouter D c0425f80 0 274 2 0x00000000
<4>[ 367.075286] Backtrace:
<4>[ 367.076354] [<c0425bbc>] (schedule+0x0/0x450) from [<c004f748>] (rr_read+0x178/0x1a4)
<4>[ 367.076751] [<c004f5d0>] (rr_read+0x0/0x1a4) from [<c004f900>] (do_read_data+0x1c/0xa08)
<4>[ 367.077453] [<c004f8e4>] (do_read_data+0x0/0xa08) from [<c00ae168>] (worker_thread+0x18c/0x238)
<4>[ 367.078186] [<c00adfdc>] (worker_thread+0x0/0x238) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 367.078887] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 367.079284] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c2bd70
<3>[ 367.081268] INFO: task audio_mvs:428 blocked for more than 120 seconds.
<3>[ 367.081634] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 367.082305] audio_mvs D c0425f80 0 428 2 0x00000000
<4>[ 367.083679] Backtrace:
<4>[ 367.084381] [<c0425bbc>] (schedule+0x0/0x450) from [<c005101c>] (__msm_rpc_read+0x22c/0xa4c)
<4>[ 367.085052] [<c0050df0>] (__msm_rpc_read+0x0/0xa4c) from [<c0051858>] (msm_rpc_read+0x1c/0x88)
<4>[ 367.085479] [<c005183c>] (msm_rpc_read+0x0/0x88) from [<c0074f34>] (audio_mvs_thread+0x4c/0x164)
<4>[ 367.086151] r6:00000000 r5:c7e69f9c r4:c05ef368
<4>[ 367.087554] [<c0074ee8>] (audio_mvs_thread+0x0/0x164) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 367.088195] r8:00000000 r7:c05ef368 r6:c0074ee8 r5:c7e69fcc r4:c7c1df48
<4>[ 367.090545] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 367.090911] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df48
<3>[ 367.092895] INFO: task krmt_storagecln:460 blocked for more than 120 seconds.
<3>[ 367.093627] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 367.093994] krmt_storagecln D c0425f80 0 460 2 0x00000000
<4>[ 367.095336] Backtrace:
<4>[ 367.096038] [<c0425bbc>] (schedule+0x0/0x450) from [<c004a1c4>] (rpc_clients_cb_thread+0x98/0x1b0)
<4>[ 367.096771] [<c004a12c>] (rpc_clients_cb_thread+0x0/0x1b0) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 367.097442] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 367.097808] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1ddf8
<3>[ 367.099822] INFO: task voice:740 blocked for more than 120 seconds.
<3>[ 367.100189] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 367.100860] voice D c0425f80 0 740 2 0x00000000
<4>[ 367.102203] Backtrace:
<4>[ 367.102905] [<c0425bbc>] (schedule+0x0/0x450) from [<c04266e8>] (schedule_timeout+0x24/0x23c)
<4>[ 367.103637] [<c04266c4>] (schedule_timeout+0x0/0x23c) from [<c04264e0>] (wait_for_common+0x12c/0x1f0)
<4>[ 367.104034] r7:c76f2000 r6:00000002 r5:c05eaf44 r4:7fffffff
<4>[ 367.106018] [<c04263b4>] (wait_for_common+0x0/0x1f0) from [<c0426684>] (wait_for_completion+0x1c/0x20)
<4>[ 367.106750] [<c0426668>] (wait_for_completion+0x0/0x20) from [<c005a38c>] (voice_thread+0x6c/0x554)
<4>[ 367.107452] [<c005a320>] (voice_thread+0x0/0x554) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 367.107849] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 367.108520] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df30
<6>[ 486.697143] [BATT] M2A_RPC: level_update: 69 at 480497997575 (2013-08-30 18:31:23.603963416 UTC)
<6>[ 486.699218] [BATT] power_supply_changed: battery at 480500162209 (2013-08-30 18:31:23.606036587 UTC)
<6>[ 486.718139] pm8058_pwm_led_brightness_set: bank 0 brightness 0
<6>[ 486.737762] pm8058_pwm_led_brightness_set: bank 1 brightness 1
<3>[ 487.220397] INFO: task audio_mvs:428 blocked for more than 120 seconds.
<3>[ 487.221069] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 487.221466] audio_mvs D c0425f80 0 428 2 0x00000000
<4>[ 487.222778] Backtrace:
<4>[ 487.223541] [<c0425bbc>] (schedule+0x0/0x450) from [<c005101c>] (__msm_rpc_read+0x22c/0xa4c)
<4>[ 487.224243] [<c0050df0>] (__msm_rpc_read+0x0/0xa4c) from [<c0051858>] (msm_rpc_read+0x1c/0x88)
<4>[ 487.224945] [<c005183c>] (msm_rpc_read+0x0/0x88) from [<c0074f34>] (audio_mvs_thread+0x4c/0x164)
<4>[ 487.225341] r6:00000000 r5:c7e69f9c r4:c05ef368
<4>[ 487.227020] [<c0074ee8>] (audio_mvs_thread+0x0/0x164) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 487.227691] r8:00000000 r7:c05ef368 r6:c0074ee8 r5:c7e69fcc r4:c7c1df48
<4>[ 487.229736] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 487.230468] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df48
<3>[ 487.232208] INFO: task krmt_storagecln:460 blocked for more than 120 seconds.
<3>[ 487.232879] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 487.233551] krmt_storagecln D c0425f80 0 460 2 0x00000000
<4>[ 487.234588] Backtrace:
<4>[ 487.235290] [<c0425bbc>] (schedule+0x0/0x450) from [<c004a1c4>] (rpc_clients_cb_thread+0x98/0x1b0)
<4>[ 487.235992] [<c004a12c>] (rpc_clients_cb_thread+0x0/0x1b0) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 487.236694] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 487.237365] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1ddf8
<3>[ 487.239044] INFO: task voice:740 blocked for more than 120 seconds.
<3>[ 487.239715] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 487.240081] voice D c0425f80 0 740 2 0x00000000
<4>[ 487.241485] Backtrace:
<4>[ 487.242187] [<c0425bbc>] (schedule+0x0/0x450) from [<c04266e8>] (schedule_timeout+0x24/0x23c)
<4>[ 487.242889] [<c04266c4>] (schedule_timeout+0x0/0x23c) from [<c04264e0>] (wait_for_common+0x12c/0x1f0)
<4>[ 487.243560] r7:c76f2000 r6:00000002 r5:c05eaf44 r4:7fffffff
<4>[ 487.245269] [<c04263b4>] (wait_for_common+0x0/0x1f0) from [<c0426684>] (wait_for_completion+0x1c/0x20)
<4>[ 487.245971] [<c0426668>] (wait_for_completion+0x0/0x20) from [<c005a38c>] (voice_thread+0x6c/0x554)
<4>[ 487.246673] [<c005a320>] (voice_thread+0x0/0x554) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 487.247375] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 487.247772] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df30
<6>[ 491.649566] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 491.650665] [ATS][set_vibration][successful]
<6>[ 491.674682] [VIB]vibrator_timer_func
<6>[ 492.960632] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 492.961486] [ATS][set_vibration][successful]
<6>[ 492.985748] [VIB]vibrator_timer_func
<6>[ 494.228454] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 494.229370] [ATS][set_vibration][successful]
<6>[ 494.253662] [VIB]vibrator_timer_func
<6>[ 494.353851] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts:
<6>[ 505.722808] EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts:
<6>[ 507.874176] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 507.875091] [ATS][set_vibration][successful]
<6>[ 507.899688] [VIB]vibrator_timer_func
<6>[ 510.369537] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 510.370391] [ATS][set_vibration][successful]
<6>[ 510.394653] [VIB]vibrator_timer_func
<6>[ 512.736968] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 512.738128] [ATS][set_vibration][successful]
<6>[ 512.762573] [VIB]vibrator_timer_func
<6>[ 514.352325] Touch: calibration confirm
<6>[ 514.373626] Touch Status: 0x01 0x10 0x77 0xA1 0x0A
<6>[ 514.381561] Touch Status: 0x01 0x00 0x77 0xA1 0x0A
<6>[ 514.776885] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 514.777862] [ATS][set_vibration][successful]
<6>[ 514.802093] [VIB]vibrator_timer_func
<6>[ 519.868621] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 519.869506] [ATS][set_vibration][successful]
<6>[ 519.893737] [VIB]vibrator_timer_func
<6>[ 522.455322] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 522.456207] [ATS][set_vibration][successful]
<6>[ 522.480499] [VIB]vibrator_timer_func
<6>[ 523.943817] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 523.944732] [ATS][set_vibration][successful]
<6>[ 523.969024] [VIB]vibrator_timer_func
<6>[ 529.148071] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 529.149322] [ATS][set_vibration][successful]
<6>[ 529.173309] [VIB]vibrator_timer_func
<6>[ 536.841979] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 536.843017] [ATS][set_vibration][successful]
<6>[ 536.867218] [VIB]vibrator_timer_func
<6>[ 543.078704] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 543.079650] [ATS][set_vibration][successful]
<6>[ 543.103851] [VIB]vibrator_timer_func
<6>[ 546.098419] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 546.099304] [ATS][set_vibration][successful]
<6>[ 546.123565] [VIB]vibrator_timer_func
<6>[ 547.273925] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 547.274871] [ATS][set_vibration][successful]
<6>[ 547.299133] [VIB]vibrator_timer_func
<6>[ 549.013427] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 549.014587] [ATS][set_vibration][successful]
<6>[ 549.038635] [VIB]vibrator_timer_func
<6>[ 550.455963] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 550.456909] [ATS][set_vibration][successful]
<6>[ 550.481201] [VIB]vibrator_timer_func
<6>[ 551.694274] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 551.695129] [ATS][set_vibration][successful]
<6>[ 551.719390] [VIB]vibrator_timer_func
<6>[ 562.994323] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 562.995758] [ATS][set_vibration][successful]
<6>[ 563.019470] [VIB]vibrator_timer_func
<6>[ 569.194122] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 569.195098] [ATS][set_vibration][successful]
<6>[ 569.219329] [VIB]vibrator_timer_func
<6>[ 569.385711] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts:
<3>[ 569.644683] tc: version magic '2.6.35.10 preempt mod_unload ARMv7 ' should be '2.6.35.10-g13f6602 preempt mod_unload ARMv7 '
<6>[ 572.967926] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts:
<3>[ 573.057800] EXT3-fs (mmcblk0p28): error: couldn't mount because of unsupported optional features (40)
<3>[ 573.058654] EXT2-fs (mmcblk0p28): error: couldn't mount because of unsupported optional features (40)
<6>[ 573.118988] EXT4-fs (mmcblk0p28): mounted filesystem with ordered data mode. Opts: (null)
<3>[ 573.575347] EXT3-fs (mmcblk0p29): error: couldn't mount because of unsupported optional features (240)
<3>[ 573.576202] EXT2-fs (mmcblk0p29): error: couldn't mount because of unsupported optional features (240)
<4>[ 573.578399] EXT4-fs (mmcblk0p29): warning: checktime reached, running e2fsck is recommended
<6>[ 573.636688] EXT4-fs (mmcblk0p29): mounted filesystem without journal. Opts: (null)
<6>[ 606.694824] [BATT] M2A_RPC: set_charging: 100 at 600378089037 (2013-08-30 18:33:23.484603659 UTC)
<6>[ 606.695129] Switch charger CHECK
<6>[ 606.695495] TPS65200 STATUS_A27
I´m to late... But extract attached folder and push the folder in the ROM.zip ...
It´s a fix
Some lines are wrong in updater-script