Related
Ok, i've had a problem with it, first i removed the protector that was as large as the device and made the screen very ugly, then i got the one from the box and putted it on, every air-bulb was gone when i kept rubbing etc.
1 stayed, under that bulb there was something white, i found out it was a 'piece' of dust.
It was kind of annoying so i removed the screen-protector, now when im trying to put it on i get lots of 'dust-bubbles',
Anyone has an idea of how to do it or should i just leave my diamond without the screen protector?
Protection
Personally i prefer to have a screenprotecter on my device. I can recommend invisible shield. its very durable and will not be scratched. check it out on www.zagg.com
If you remove the protector, then there will alway be dust next time, because the dust get stuck to the protector glue. (I have also remove mine several times)
I have tried zagg, but I can't recommend it. It is a little sticky (which they also says on their homepage) and I don't like that. The floating feeling is gone. It is also not that invisible.
I have selected to buy a new original protector, and will use that.
The trick to get it on without bobbles is to start on the long edge and then slowly add it. (Keep the 'paper' on as long a possible).
(Michael
willyy1991 said:
Ok, i've had a problem with it, first i removed the protector that was as large as the device and made the screen very ugly, then i got the one from the box and putted it on, every air-bulb was gone when i kept rubbing etc.
1 stayed, under that bulb there was something white, i found out it was a 'piece' of dust.
It was kind of annoying so i removed the screen-protector, now when im trying to put it on i get lots of 'dust-bubbles',
Anyone has an idea of how to do it or should i just leave my diamond without the screen protector?
Click to expand...
Click to collapse
The original is washable. Wash it and dry it with a paper towel that sucks in the water bubbles, wipe dry and clean your screen and reapply it.
By the way, this goes to Accessories forum.
mhfalken said:
If you remove the protector, then there will alway be dust next time, because the dust get stuck to the protector glue. (I have also remove mine several times)
I have tried zagg, but I can't recommend it. It is a little sticky (which they also says on their homepage) and I don't like that. The floating feeling is gone. It is also not that invisible.
I have selected to buy a new original protector, and will use that.
The trick to get it on without bobbles is to start on the long edge and then slowly add it. (Keep the 'paper' on as long a possible).
(Michael
Click to expand...
Click to collapse
Where can you buy a new one, i need it really fast because my phone is without protection right now and no i am affraid of pressing it to hard to leave a permanent mark..
tnyynt said:
The original is washable. Wash it and dry it with a paper towel that sucks in the water bubbles, wipe dry and clean your screen and reapply it.
By the way, this goes to Accessories forum.
Click to expand...
Click to collapse
I did this and the dust keeps coming at the protector and my phone and there will be bubles because the dust gives it a 'height-problem'..
I bought invisible shield for mine, its pretty nice after say 4 days from install.
For first 2 days it might seem really bad but it gets much better.
I somehow scratched it without even noticing it, so I sent picture to zagg and they sent me new one. Even though scratch was very minor.
mhf
hi. this my first post on this web site
excuse me for my bad english
i have a diamond and i remove orginal screen protecter because i write sms with letter recorgnizer and the area that i write words on the screen become white and scratch. i remove orginal and buy a new one that for iphone. i cut it for my phone size and apply it. its sooo much stiky and i have a problem like orginal one.i wnat to remove it and when i do it a tiny layer of glue stand on my diamond screen. i can't clean it. and it give a bad scene to my diamond.
what's your idea. i give u a pichture from my diamond screen.
Perhaps you could use isopropyl alcohol, usually it will remove glue without damaging the plastics surface (in that case: your display). DON'T USE nail polish remover, acetone or even benzine, it will remove the glue too - but your display would look "milky". You can get isopropyl alcohol at the pharmacy.
Tell us if that helped you
mhf said:
hi. this my first post on this web site
excuse me for my bad english
i have a diamond and i remove orginal screen protecter because i write sms with letter recorgnizer and the area that i write words on the screen become white and scratch. i remove orginal and buy a new one that for iphone. i cut it for my phone size and apply it. its sooo much stiky and i have a problem like orginal one.i wnat to remove it and when i do it a tiny layer of glue stand on my diamond screen. i can't clean it. and it give a bad scene to my diamond.
what's your idea. i give u a pichture from my diamond screen.
Click to expand...
Click to collapse
You might be interested in this thread: http://forum.xda-developers.com/showthread.php?t=421229
I didn't get a screen protector with mine... I mean, I had a shipment protector with a little tab for peeling off, but nothing came with it for long term use. It's a Sprint, did they just not include one?
the exim screen protector is very good and smooth
I always use the Brando screenprotectors. See their online shop. They ship worldwide for only $ 3,00 shippingcosts.
It is very easy to install, easy to clean, 100% garanteed scratch free and very durable.
iixnullxii said:
I didn't get a screen protector with mine... I mean, I had a shipment protector with a little tab for peeling off, but nothing came with it for long term use. It's a Sprint, did they just not include one?
Click to expand...
Click to collapse
I've got a Sprint Diamond too, and didn't think I got a protector either, but it was in the separate bag that has the manuals. It should have come with one...Wish it woulda come with an extra one too, oh well.
I had the same problem with misalignment and dust bubbles with the HTC protector on my first few tries...i did however fix the problem...
Take the protector off and clean off the phone...use a microfiber cloth to get all the dust and oil off...after its super clean...take the protector and wash it off with some mild soap...rub the soap in with your fingers and get it clean. Be sure to note which side is down. After its clean, hold it around the edges and let the water bead off...i blew on the protector to get residual water off...some water is ok...actually helps with the install...the basically carefully apply it still holding the sides making sure not to leave finger prints. Start from the top and work your way down... i used a credit card pushed against the microfiber cloth to squeegie the protector down...be carefull with the few drops of water. After you have it down...there might be little bubbles or what looks like water spots where water is trapped under the screen...dont worry...just use your phone and leave it alone. Once it heats up from the excessive phone use it will start to dry up and the protector will come out very nice and smooth. Mine is flawless and i did the wash with soap apply and remove at least 3 or 4 times to get it right...Just be patient
I use screen protector from martinfields, what do you say about, anyone have one??
I think the best in market
My HTC one got a nasty scratch in it last week, so I ordered a Martin Fields.
It arrived this morning and I've got it on without any problems. So far I've noticed:
- It's not a perfect fit like the HTC one was. The hole for the speaker at the top is larger than the hole in the phone. It's not bad though.
- The visibility of the screen does seem better than the HTC protector, but I don't know if it's just the placebo effect of having a more expensive protector.
- It was _easy_ to put on, no bubbles at all
- The protector for the bottom buttons is awful. The circle is just the right size to completely hinder using the touch wheel and it's obvious that you've got a piece of plastic on there.
- It seems smoother than the original HTC one when using the stylus.
So far I'm impressed with it. I didn't bother with the camera hole or bottom hard buttons. The in box HTC one was fine for me, but when I got a scratch on it (my stylus somehow developed a sharp edge), it annoyed me.
I'm using the one supplied as standard with a uk CompactIV and it's great- you can hardly tell it's thereand the sensitivity seems fine.
I have 24 diamond screen protectors. Because i bought 24 diamonds and sold them all without screen protectors so i am sorted untill i buy another phone.
After using the martin fields one for a couple of days, I think it's great.
The screen looks much brighter and clearer through it (I thought the HTC one was great, but I do notice the difference). Plus the smoothness is brilliant, theres pretty much no friction for the stylus or fingers
where can i purchase the htc screen protector? the original that comes in the box...
Recently received the Phantom Skinz Full Body set and have gone through installation.
Here's the breakdown:
The Pros:
- The Screen Skin looks good and feels good. The extra drag vs. the stock glass is slight and the overall clarity is very good (doesn't have any noticeable detraction from the crisp, contrasty screen).
- The main screen skin and front overlays were fairly easy to apply and once dried have a very nice unobtrusive look
- Comes with 2 sets of skins
The Cons:
- included directions are WAY OFF from the install video on their site. Soaking times, how long to let it sit and dry, etc...
- Edge bubbling on every corner for the back overlays. Directions say to "cup the corner with palms and hold 30 seconds", but I've done it over and over again and they keep popping off after a short while
- A WHOLE LOT of wet work involved in applying these skins. Application involves soaking the skin in water first, then (as instructed) with your fingers fully wet, take the wet skin and put it wet onto the phone and then use the included credit card shaped "squeegy" to push out the extra water. Not so much a big deal for the screen skin, but getting that much water around and near the audio/mic/power and such ports while putting on the body skins is asking for trouble.
Final Thoughts
I imagine in some small (heck, maybe in large) part, the corner bubbling issue is due to me not applying the skin properly. But I'm not some clueless granny that doesn't know the difference between a mouse and a blackberry and the included instructions are vague in important places and almost completely different than the video instructions shown at their website (for example; The included instructions say to use warm water WITH SOAP)
Bottom line: Stick with just the screen skin, skip the full body.
The online video instructions say to use soap as well. IIRC, she said that at their facility, they use one drop of Johnson's baby shampoo per 32 oz of water.
I would avoid Phantom Skinz altogether. Here's the review I posted about my experience with one of them on my Moto Droid in the skins topic.
Phantom Skinz
I got a PS for my Moto Droid because I didn't want something as grippy as the Zagg. PS had great reviews and came with 2 full sets for the price of 1 zagg with 33% off on top of that ($16.50 in the end). The first installation of the screen got some dust and fuzz under it since I was OCD about getting it perfect, so I emailed them and they sent me a replacement for free no questions asked. I know it did come with two sets of protectors but I wanted to keep one as a backup still. Second installation was perfect. No dirt, dust, fuzz or finger prints. Screen was perfectly smooth (no orange peel) and the touch felt almost the same as the glass. Put the rest of the body on without a problem as well with just a few bubbles in some of the tougher spots. I was very impressed, but now a month later I am not so much. After daily use taking my phone in and out of my pocket (sometimes shared with keys) the skin is filled with knicks and wrinkles. While the film may not technically scratch, it is vulnerable to indentations and air bubbles forming which do not "self heal". Instead of scratching, it seems like the skin stretches in place, resulting in a wrinkle/groove with little marks that look like air bubbles underneath. Not only does it make the screen look dirty, but you feel them while using the touch screen. As I write this, I just dug my finger nail into the screen and tried to scratch it, leaving another permanent groove. Needless to say, I will be taking off the PS and throwing it in the trash. The rest of the body has surprisingly stayed pretty clean of wrinkles, so it may have something to do with its application on glass. I will put some pictures up when I get the chance this evening. Overall, I would not recommend PhantomSkinz. It looked and felt great for a couple weeks, but now every day I am finding more and more knicks and wrinkles and that is just unacceptable compared to others. This skin is NOT scratch proof like other comparable skins on the market! However, I will commend their customer service for being very helpful and quick to reply.
And here a pictures of what it looks like:
h ttp://forum.xda-developers.com/showpost.php?p=5415251&postcount=44
(remove the space after the h, I can't post links yet)
Bottom line here as that they are smoother than other brands but scratch pretty easily. You should check back in on this topic in a month or two and see if your opinion has changed.
I applied the full body skin about a week ago. There's definitely a lot of water involved but most of the danger can be avoided with some caution. I used Q-tips to do a lot of the credit card work around the edges so that it soaked up the water it pushed out.
A good trick for the corners is to use some sealant/piping tape to hold them down. This is a lot better than using your hand for 30 seconds, and you can leave it there for as long as you want (I left the tape on mine for 2 days since I wasn't going anywhere that I needed to show off my phone, I figured why not? Now my corners are perfect).
So far I like PhantomSkinz because it wraps the corners a little better than the other skins. Bodyguardz is a little better in clarity and material. InvisibleShield has too much of the orange peel effect. Haven't had a chance to try BestSkinsEver.
As for detonation's review, it's too early for me to tell if I'll have the same problems, but I agree that the material doesn't seem on par with InvisibleShield or BodyGuardz. But since I still used the carrying case and treat my phone with much care even with the skin on, I don't think it'll be too much of a problem.
I recently got the phantom skinz full body set, after I read the instructions I thought that there was no way I was applying wet/soapy film to my N1, it just doesn't make any sense. Water/soap plus electronics? Its a recipe for disaster, besides the fact that I suck at arts and crafts type stuff just like this. I would imagine I would get water somewhere inside the device, and knowing me it would reach the many water detectors in the phone. It doesn't seem worth it, so I applied just the screen part sans water/soap, and needless to say it sucked big time, even when I got all the bubbles out.. it had a terrible gray haze on parts of the screen it was bad (maybe due to not using the water/soap method). Can any one suggest just a simple screen protector that doesn't' require to dunk your device in water?
boxmander said:
I recently got the phantom skinz full body set, after I read the instructions I thought that there was no way I was applying wet/soapy film to my N1, it just doesn't make any sense. Water/soap plus electronics? Its a recipe for disaster, besides the fact that I suck at arts and crafts type stuff just like this. I would imagine I would get water somewhere inside the device, and knowing me it would reach the many water detectors in the phone. It doesn't seem worth it, so I applied just the screen part sans water/soap, and needless to say it sucked big time, even when I got all the bubbles out.. it had a terrible gray haze on parts of the screen it was bad (maybe due to not using the water/soap method). Can any one suggest just a simple screen protector that doesn't' require to dunk your device in water?
Click to expand...
Click to collapse
Dude... you BARELY have to use any water to get the screen to turn out right. Sorry you wasted your PS... but ask them for a replacement, and mail it to me! I do this **** with my eyes closed. It's really not rocket science, and you don't have to "dunk" your phone in water.
boxmander said:
I recently got the phantom skinz full body set, after I read the instructions I thought that there was no way I was applying wet/soapy film to my N1, it just doesn't make any sense. Water/soap plus electronics? Its a recipe for disaster, besides the fact that I suck at arts and crafts type stuff just like this. I would imagine I would get water somewhere inside the device, and knowing me it would reach the many water detectors in the phone. It doesn't seem worth it, so I applied just the screen part sans water/soap, and needless to say it sucked big time, even when I got all the bubbles out.. it had a terrible gray haze on parts of the screen it was bad (maybe due to not using the water/soap method). Can any one suggest just a simple screen protector that doesn't' require to dunk your device in water?
Click to expand...
Click to collapse
you didnt follow the instructions and it didnt work well for you? gtfo
boxmander said:
I recently got the phantom skinz full body set, after I read the instructions I thought that there was no way I was applying wet/soapy film to my N1, it just doesn't make any sense. Water/soap plus electronics? Its a recipe for disaster, besides the fact that I suck at arts and crafts type stuff just like this. I would imagine I would get water somewhere inside the device, and knowing me it would reach the many water detectors in the phone. It doesn't seem worth it, so I applied just the screen part sans water/soap, and needless to say it sucked big time, even when I got all the bubbles out.. it had a terrible gray haze on parts of the screen it was bad (maybe due to not using the water/soap method). Can any one suggest just a simple screen protector that doesn't' require to dunk your device in water?
Click to expand...
Click to collapse
Try clairivue or martin fields. Just do a google search since I can't post links yet.
typ_ex said:
you didnt follow the instructions and it didnt work well for you? gtfo
Click to expand...
Click to collapse
LOL! i agree. i have had no issues at all with my phantomskinz- both on the magic and now my nexus- i'll admit i do suck at installing them but what i do is get a bowl o water, put a few drops of baby shampoo in swich it around a bit, then dunk the piece in there- hold it over bowl until excess is removed then you can put it on device- the soap/water allows you to move it into position easily and helps squeegee the bubbles....
i wouldnt blame a product because you didnt follow their instructions how to install it...
I actually prefer the bowl of soapy water to the sprays that come with other skins. Submerging it ensures the entire skin is lubed up, and the small amounts of drips on the device is harmless. Just let it dry out overnight before turning it on.
I think Martins is completely over priced. I tried BSE and Phantom and all works great. Once dried it is practically invisible with only the slightest orange peel effect. I'm pretty OCD and it is minimal enough that it doesn't bother me. What does bother is that both of the screen protectors are slightly shorter than the screen.
As for applying the phantom and drowning in water as people are saying I don't do that. I've put on enough of these to know you only need a slight amount. I use a spray and just mist the backing so that it is enough to be able to adjust when putting on but not dripping with water. I use a cloth to absorb the water on the edges as I push the bubbles/excess water out. Fairly easy process. It just takes a slow hand and patience.
pongalong said:
A good trick for the corners is to use some sealant/piping tape to hold them down. This is a lot better than using your hand for 30 seconds, and you can leave it there for as long as you want (I left the tape on mine for 2 days since I wasn't going anywhere that I needed to show off my phone, I figured why not? Now my corners are perfect).
Click to expand...
Click to collapse
Ok I have to ask: what is sealant / piping tape? And where do you buy that? Home Depot? Bed, Bath and Beyond?
Paul22000 said:
Ok I have to ask: what is sealant / piping tape? And where do you buy that? Home Depot? Bed, Bath and Beyond?
Click to expand...
Click to collapse
Some might know it as teflon tape, thread seal tape or plumbers tape. It's a thin white non-adhesive tape that you use on pipes/hoses to make connections water tight. Home Depot would have it or any hardware store - it's pretty common. Just cut a few good length pieces and wrap your phone up like a mummy on the difficult spots. It works well because it's stretchy, conforms to shape and naturally adheres to the phone skin.
pongalong said:
Some might know it as teflon tape, thread seal tape or plumbers tape. It's a thin white non-adhesive tape that you use on pipes/hoses to make connections water tight. Home Depot would have it or any hardware store - it's pretty common. Just cut a few good length pieces and wrap your phone up like a mummy on the difficult spots. It works well because it's stretchy, conforms to shape and naturally adheres to the phone skin.
Click to expand...
Click to collapse
...and it's non-stick!
typ_ex said:
you didnt follow the instructions and it didnt work well for you? gtfo
Click to expand...
Click to collapse
Like I mentioned before, my application didn't work well cause I didn't follow the instructions. And I wasn't hating on PS, get a grip. Besides after some people posted about this topic I might give it another go, PS gave me two for one so I can redo it. Why are you here? Perhaps you should try posting things that are more constructive.
pongalong said:
Some might know it as teflon tape, thread seal tape or plumbers tape. It's a thin white non-adhesive tape that you use on pipes/hoses to make connections water tight. Home Depot would have it or any hardware store - it's pretty common. Just cut a few good length pieces and wrap your phone up like a mummy on the difficult spots. It works well because it's stretchy, conforms to shape and naturally adheres to the phone skin.
Click to expand...
Click to collapse
Interesting. I'll definitely get some. Thanks for the tip.
Hmm... I'm going to go to Home Depot to buy some kind of special tape I've never heard of to wrap up my phone like a mummy in order to prevent the corners from lifting on my phone's skin protector. Phone enthusiast or what?
Phantom does have the best skins by far...
The trick to installation to make it perfect:
Use the Johnson's/water mix as they advised.
Ignore all of their other directions.
Peel off the piece you want to apply. Dryly.
Dip your fingers in the water and apply it to the skin using your fingers.
Once both sides of the skin are wet, use your fingers as a squeegee to pull off any excess water.
Apply the skin to your phone. Keep the skin sitting on your phone in it's original shape.
Use your fingers, not the applicator card, to squeegee out the air bubbles. You don't need to apply very much pressure at all. The bubbles move around extremely easily.
Now, let the skin dry for about 2 minutes. Once you notice the skin starting to cling to the phone a little harder, grab the ends that you need to wrap around the phone and stretch them into place. This is the key step. Stretching it makes it stick so much better, the corners align perfectly with the phone when you do this, and all the gaps left between the skin pieces when you don't stretch it are gone. The skin has to be stretched to fit the phone, otherwise the pieces will all be a little to small and the corners will blow.
Repeat with the other pieces.
Enjoy your sexily phantom skinned N1.
anyone with pics of this case ?
I just wanted to comment about Phantom Skinz because I have had a really good experience with them and I am going to get another set from them as soon as they release it for the HD2!
I got Phantom Skinz for a Nano about a year ago and it has been awesome! I bought the PS retail (they have a location in my area) so I only got one set, but I did it myself with no problems. I had to take it off for a warranty replacement on the Nano and I put the same skin back on the new Nano and it looks just as good as it did on the first application. It's awesome that it can be taken off and put back on again using only water.
I got GA for my G1, but it is the worst product ever. I had it professionally installed at a Ghost Armor location because I wanted it to be perfect for my baby. But it didn't even last a month before it started peeling! GA can only be applied once with a special solution (thats what the GA salespeople told me) and it can't be fixed with water like Phantom Skinz. Phantom Skinz has never actually peeled like the GA did, but at least I could fix PS with water if I needed to!
I literally had the full body GA skin replaced 4 times in the course of a year because it peeled so bad and I am not just talking the corners! I did everything they told me to; keep the phone in a case so it doesnt rub in your pocket, keep any liquid of the phone (durr), don't leave the skin in prolonged sunlight, blah bla blah.
It was $35 for the original GA skin and installation and then they charged me $10 labor for the "free warranty replacement" every time I had the skin redone. Oh, and they changed the GA product for my phone 3 times out of the 4 I got it replaced and the changes never fixed any of the problems I had with the skin. GA also yellowed really bad and actually got progressively worse over the course of their " improved product revisions". The last time I had the G1 wrapped the skin was a pretty moderate yellow in about a week...
The salespeople sucked me in every time with leading me to believe the GA skin for the G1 was revised and the problems were fixed. I spent way too much money on their crappy ass product!
Ghost Armor is an awful product! Please just stay the hell away from them!
There is no need to submerge anything in any fluid. I have installed clear skins on many devices by using soapy water. I dont spray it on the phone, I spray a small mist on the protector before applying. Trust me there is not enough water to damage anything because as i push out the bubble I wipe the water.
If you are concerned about it then remove the battery and wait a day like the other people have suggested. once the process is complete the skin will need to settle for a few days before it looks good.
I used some spray that came with a skin before and I did not like it compared to the soapy water MIST.
I also do not use the skin on touch screens because my finger drags on it compared to other screen protectors that are designed to protect the screen.
Hey everybody, got a new case review. This one is the infamous Nillkin Fresh, which is Nillkin's second generation of flip covers. To be honest, I got this case because it works with the iloome ScreenMate tempered glass protector I got, which didn't work with any of my other cases.
I got the yellow color, and it looks very nice. The flip has a darker yellow than the snap on part, which looks perfectly fine to me. The flip doesn't stay down for the first few days, and it doesn't have a lock mechanism. But, with a few days use, the flap does stay down on itself. Now, at first it wasn't working with my tempered glass protector, so I just kept stretching the fake leather out, and eventually it stays. I just clamped it so it stayed stretched. This is a very simple case, and if you don't drop your phone a lot (like me) this is a really nice case, it has a soft lining on the inside of the flip, almost like micro-fiber, and it helps keep fingerprints away. I do like this case, but it's not perfect. You can also use it as a stand, just fold it back and slide it into the slot. I absolutely HATE this feature, as the slot sticks out from the back of the case, so I can't use it with the Orb Charger. I forgot to take pictures of it, but it is REALLY annoying. Overall, aside from that one thing, it's a really nice case. :laugh:
Just to add on to OP, mine's the light blue one, a really sweet colour.
Has a microfiber (or whatever you call that) lining, prevents the screen from getting scratched.
The thickness. When paired with apps like Proximity AutoLock. you simply flip the cover and BAM, the phone locks itself. (Disclaimer: The app takes up quite a lot of battery though.)
Thickness again.
Thickness compared to a bumper. (if you haven't realized yet, I like blue )
The back plastic has got this pearly, glittery effect, too subtle to notice unless you're staring at it.
The front is a leathery kind of texture. Not real leather, of course.
It does destroy the edge swiping experience, with the exception the left hand side center (shown in the pic). May cause full screen SPs to bubble up too, but I have no idea, I don't use full screen ones.
How it looks. Mine has yet to become seasoned, so it'll topple if I don't support it. It has a hook that'll hook the front cover.
The headphone jack.
Those with a dbrand skin might want to take note, it kinda leaves a mark on the skin, but if you don't use the case for long enough, the mark'll go away.
I'd recommend it 8/10 overall as it makes it hard to use the phone using your left hand with the front flap, also, it makes my phone feel like a tank. But the front protection is great if you're not using a screen protector. But be careful of oil stains, they're almost impossible to remove from the inner lining. Washed it once, dried it and it feels like new again.
Edit, does anybody know how the hell do I resize the pictures? They're HUGE.
jiayit said:
Just to add on to OP, mine's the light blue one, a really sweet colour.
Has a microfiber (or whatever you call that) lining, prevents the screen from getting scratched.
The thickness. When paired with apps like Proximity AutoLock. you simply flip the cover and BAM, the phone locks itself. (Disclaimer: The app takes up quite a lot of battery though.)
Thickness again.
Thickness compared to a bumper. (if you haven't realized yet, I like blue )
The back plastic has got this pearly, glittery effect, too subtle to notice unless you're staring at it.
The front is a leathery kind of texture. Not real leather, of course.
It does destroy the edge swiping experience, with the exception the left hand side center (shown in the pic). May cause full screen SPs to bubble up too, but I have no idea, I don't use full screen ones.
How it looks. Mine has yet to become seasoned, so it'll topple if I don't support it. It has a hook that'll hook the front cover.
The headphone jack.
Those with a dbrand skin might want to take note, it kinda leaves a mark on the skin, but if you don't use the case for long enough, the mark'll go away.
I'd recommend it 8/10 overall as it makes it hard to use the phone using your left hand with the front flap, also, it makes my phone feel like a tank. But the front protection is great if you're not using a screen protector. But be careful of oil stains, they're almost impossible to remove from the inner lining. Washed it once, dried it and it feels like new again.
Edit, does anybody know how the hell do I resize the pictures? They're HUGE.
Click to expand...
Click to collapse
You could just use a photo editor and re-crop?
Sent from my Nexus 4, the only phone approved by Patrick Star
N4ever said:
You could just use a photo editor and re-crop?
Sent by a giant douche
Click to expand...
Click to collapse
While we're doling out advice, I recommend that you change the text you quote so everyone doesn't have a second column of gigantic images...
N4ever said:
You could just use a photo editor and re-crop?
Sent from my Nexus 4, the only phone approved by Patrick Star
Click to expand...
Click to collapse
You could have said that without quoting the images all over again....
I have this case too, just never got around to finish writing my review. Mine is mint green (though some product pictures may appear turquoise).
Having a front cover in addition to the case is definitely nice, as I can drop it into my bag without worrying about what is going to hit against the front screen. Also very handy when talking on the phone with the flap covering the screen.
It's not slim as a ringke slim but not thick either, and the phone looks nice in it. I liked that it didn't have an actual lock to keep the cover on because it was easier to flip open.
It's so annoying when your holding it open. No comfortable way to do it.
Sent from my Nexus 4, the only phone approved by Patrick Star
Are the buttons easy to press?
Sent from my Nexus 4 using Tapatalk 4 Beta
Tbh it's quite hard. And trying to take a screenshot with both buttons is a nightmare. But I don't take that many screenshots anyway and the power button is not really that hard to press, it's just that their opening hole for the power button is a tad too small.
jiayit said:
Tbh it's quite hard. And trying to take a screenshot with both buttons is a nightmare. But I don't take that many screenshots anyway and the power button is not really that hard to press, it's just that their opening hole for the power button is a tad too small.
Click to expand...
Click to collapse
I can see the volume rocker is exposed when you open the case. The power button looks a bit hard. In my current case(looks like the ringke slim) i had to cut off the bar at the top to gain easy access to power button.
Sent from my Nexus 4 using Tapatalk 4 Beta
The way everything folds is just uncomfortable.
Sent from my Nexus 4, the only phone approved by Patrick Star
I got this case last week, black one. The plastic base is super cheap, there are at least two defects and the frame around the power button is simply bent. Although my flip cover actually rests perfectly on the screen, the plastic part makes noises everytime a little pressure is applied to the sides.
Went straight to the litter bin, I'd rather use my phone naked than inside this thing.
Just my two cents.
Fabriciohss said:
I got this case last week, black one. The plastic base is super cheap, there are at least two defects and the frame around the power button is simply bent. Although my flip cover actually rests perfectly on the screen, the plastic part makes noises everytime a little pressure is applied to the sides.
Went straight to the litter bin, I'd rather use my phone naked than inside this thing.
Just my two cents.
Click to expand...
Click to collapse
Seems like you got a manufacturing defect.. Why didn't you ask for a refund?
Hung0702 said:
While we're doling out advice, I recommend that you change the text you quote so everyone doesn't have a second column of gigantic images...
Click to expand...
Click to collapse
Sent by a bigger douche who calls people out
Sent by an even bigger douche
Sent from my Nexus 4, the only phone approved by Patrick Star
So my idea worked and i now have a full adhesive screen protector. Covers from edge to edge and there is no halo effect. The protector is on good and does not peel/pop out. I am using a unicorn beetle pro full body case and no problems. Before the case would pop out the protector but not anymore.
What exactly was your idea?
How did you manage this? (For the people that haven't been keeping up with your posts, such as myself.)
Did you use LOCA or OCA film?
Sent from my Galaxy Note7 using Tapatalk
so much detail. so much wow. i wish there was more information, like, what you used, how you did it, instead of a brag post. thanks for the pictures though!
One of his older posts discussed using LOCA. If you use LOCA, how do you get it off if you ever want to remove the screen protector?
Yes I used LOCA glue. To take it off you just heat it. It should be easier to remove than when replacing the digitizer.
I got a couple air bubbles though but id rather have that than a scratched up screen lol
Interesting.... but more info on how to do it and what products to use would be great. Thanks OP.
I was just thinking about if this was a solution two days ago, but this is exciting news that its worked. My question is, is the LOCA a problem to handle, because i could see using too much might have some go into the speakers or just seep from the borders. when originally applied. and is there a way to make sure we don't get bubbles?
teegunn said:
Interesting.... but more info on how to do it and what products to use would be great. Thanks OP.
Click to expand...
Click to collapse
Donnyohs said:
I was just thinking about if this was a solution two days ago, but this is exciting news that its worked. My question is, is the LOCA a problem to handle, because i could see using too much might have some go into the speakers or just seep from the borders. when originally applied. and is there a way to make sure we don't get bubbles?
Click to expand...
Click to collapse
Yea i got a little on the speaker but you just have to be care full and as it seeps kut clean it with a rag. The good thing is that it wont dry until you put the black light on it. The part you have to be the most carefull with is the home button. Loca will make it sticky and a little harder to press. I also reccoment you get a protector that is completely clear as the one i got has black on the top and bottom and it prevents the black light from drying the glue under those areas. Clean the screen good. To avoid bubbles look at youtube and see how they apply it. Basically a stick figure but instead of a head it is a y shape. Carefully place the protector and let is slowly spread on its own. Once it stoos spreading then you could slowly press down on it and remove the remaining bubbles. I lined uo thw home and back buttons first and made sure the cut outs were aligned for the camera and sesors. Then i applied the black light on the bottom half furst so that it would align properly. I did this while pressing down on it because the air bubbles kept coming up. I also covered up the top half so that wouldnt dry up. Oncw i got the bottom i got rid of any air bubbles on the top half and did the same. After that i put the phone in a box., close it up, do a cut out for the black light to fit and let it sit for a couple minutes to dry more. Then i cleaned and dried the edges. Make sure not to leave too much of the loca in between the screen and protector so you wont get touch senaitivity issues. And do it where there is no dust. I oly got 1 small air bubble but some like white spots that appear to be dust. And again clean the speaker, home button, sensors, and camera before drying. You could also just scrape it off with a plastic blade that the loca came with. And make sure to use liquid version and not the film.
https://www.gadgetshieldz.com/oneplus-6-screen-protectors-covers-cases.html
I'm thinking to buy. but don't know how good are these. and also very first time so don't know how good i can apply these.
Good if these can be available offline stores
Hi!
I bought the same set only to have my glass back protected from scratches.
You need to apply them wet with dish soap water. Just take 2 or 3 drops in about 300ml water.
Hard to describe what you have to do, have a look at this video though: https://youtu.be/WzkgRprMopI
I wouldn't purchase it again. Very finicky to install (back and front go easy, sides are horrible to apply) and the overall look of your device will be something like orange peel... Not orange, but with small "dents" everywhere. I even skipped the side stickers because that really is a PITA to get them to the right place. Bottom and top are easy to assemble. But the sides including edges ... it won't stick.
I just installed it, display is a little bit grainy but I think when its dried completely you should not be able to see the grain.
Bananebieger said:
Hi!
I bought the same set only to have my glass back protected from scratches.
You need to apply them wet with dish soap water. Just take 2 or 3 drops in about 300ml water.
Hard to describe what you have to do, have a look at this video though: https://youtu.be/WzkgRprMopI
I wouldn't purchase it again. Very finicky to install (back and front go easy, sides are horrible to apply) and the overall look of your device will be something like orange peel... Not orange, but with small "dents" everywhere. I even skipped the side stickers because that really is a PITA to get them to the right place. Bottom and top are easy to assemble. But the sides including edges ... it won't stick.
I just installed it, display is a little bit grainy but I think when its dried completely you should not be able to see the grain.
Click to expand...
Click to collapse
Wow, what is all that "soup solution" garbage stuff? Any protector i just clean the phone and apply it fast and on place and no need for all that.........