Related
Flash Moto Droid to Cricket / Metro full apps, web,mms.
This is my attempt to recreate the solution from Howard Forums
i may have missed a few steps along the way but here it goes. as of 08/02/2010 - make directory now for 2.2 roms
FILES FOR FLASHING TO CRICKET (U2nl,PRL's,Autostart,SPRecovery,NV items)
Special thanks and credit should go to
SyZtyM (i recreated his thred for XDA)
gijoey1980
Tracphonejunkie
whiterabittorg
To0
Insaincain (For the nv items. You are a legend, and credit is due where credit is due**AS read from SyZtyM)
Admin (For all sites. PERIOD)
You will need:
1. CDMA WS 2.7 (google)
2.Harware Virtural Serial Port this is the demo good for 14days
3. Motorola A855 USB drivers (These are the 32bit Drivers)
4. Cyanogen Mod Rom from Rom Manager in market
5. SPRecovery
6&7.Autostart.sh & U2nl from whitrabbit.org (thanks to whiterabbit). Save autostart.sh and U2nl in C:\android\tools\.
8.download Autostart (Root) from Market
9. NV items from http://www.whiterabbit.org/android (u must generate this uniquely with you [email protected] i have included a generated [email protected] for sample or to replace x's with you MDN
Step 1. First step is to make sure you have the drivers installed on your computer, and you also need to have Android SDK installed on your computer.
You will need to root the phone, key here is to make sure the kernel you load supports iptables.
Step 2. if you need to ROOT: follow the guide
than download Rom manager over wifi from MARKET, proceed to flash clockwork and download and install cyanogen 5.xx rom, and google apps..wipe data etc.
Step 2.1 if first fails. get RSD Lite 4.6 (google), Power on phone holding down the up arrow and pressing power, this will put you into bootloader mode.
Open RSD Lite 4.6
Flash the SPRecovery_ESE81.sbf file with RSD Lite.
this should just flash the recovery if not download a rom like SMOKEDGLASS unzip and put in folder on SD named Nandroid
Once the phone is completely rebooted into rooted android, power it off.
alternately u can install BuglessBeast froyo v 02.1 from alldroid.org then skip to these steps below
Hold down “T” on the keypad and power on phone.
Plug into computer and open HW Virtual Serial Port (your drivers should install and connect etc)
In HWVS set the IP address to 192.168.16.2 and the port to 11008, choose the com port 10 click connect. (For this tutorial we will use COM10)
Open CDMA WS 2.7 and (go to settings tab and deselect NV Enabled) then connect to COM10. if you dont deselect you will get PHONE FAILED ERRORS
On security tab send SPC 000000. (msg says phone accepts blah blah blah
Go to tab labeled “Other” and write prl. For Cricket EVDO, 6499(new service plan) and 38515 is recommended.
Go to NAM and enter MIN ex. 615-555-5593 (usually different from your actual phone# and MDN(your mobile number ex. 615-555-5551 and click write.
Goto “Memory” tab and click write under NV items, find the downloaded NV items you got from here
for example you must generate the NV items by inputing your MDN([email protected]). box opens telling you to save them as .txt and select them with cdma 2.7. (Thanks again to insanecain)
It should then say, 12 NV items were successfully written to phone.
Go to Main tab and click mode reset.
You can now close HWVS and CDMA WS and open cmd.exe on your computer.
if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone
Once phone reboots go to the market using WI-FI and download and install Autostart root required
Open the Voice Dialer on the phone and say “Open APNs” and click open.
Click on the Verizon and edit everything to match below:
Name - Cricket
APN internet
Proxy wap.mycricket.com:8080
Port 8080
Username [email protected]
Password cricket
Server wap.mycricket.com
MMSC http://mms.mycricket.com/servlets/mms
MMS Proxy wap.mycricket.com
MMS Port 8080
MCC 310
MNC 004
Authentication Type PAP or CHAP
APN type <Not set>
Now click the menu button and click Save.
Before starting the next step make sure you have the u2nl file in your this folder c:/android/tools and also that you have you autostart.sh file in this folder c:/
Now go to command prompt and type the following commands,
cd c:\android\tools
adb shell
mkdir /data/opt/
exit
adb remount
adb push c:\android\tools\u2nl /system/bin/u2nl
adb push c:\android\tools\autostart.sh /data/opt/autostart.sh
Now:
adb shell
chmod 0755 /system/bin/u2nl
chmod 0755 /data/opt/autostart.sh
adb reboot
Now, once your phone has rebooted, you should have working web, mms, app, gps, and all. If you don’t go back and check all the steps to insure you did everything exactly right.
thanks everyone for reading.
i would also like to thank everyone who helped give back to the droid community by solving this, (I gave up and switched back to my eris for full support like a Beeach! which i bricked twice) im back on DROID baby
currently running BuglessBeast Froyo v 02.1 and the p3 1000 kernel.
quadrant score: 972
this is a very good set up thanks for the post!
Open CDMA WS 2.7 and (go to settings tab and deselect NV Enabled) then connect to COM10. if you dont deselect you will get PHONE FAILED ERRORS
Click to expand...
Click to collapse
I get the phone failed error, but I don't see the NV Enabled option. Nor do I see the settings tab, where is that option?
broken linkkkkkkzzzzzzzzzzzzzzzzzzzz
"the guide" http://rootyourdroid.info/guides/obtaining-root/
Click to expand...
Click to collapse
is a broken link : (
ummm...flashed new rom...now no web,mms
ok, so im trying like hell to give this moto a shot. normally an htc fan. but the display, camera, and physical keyboard for the price was enticing. i did everything and got internet for a while. then i decided to load bugless' latest rom, now i have no web or mms. is there someting i have to redo??? knowing the norm with reflashes, i did the "open APNs" and redid everything there....but still no go. do i have to redo the Command prompts and the autostart download fr market?
*edit* did all the changes over...ALL. Still no web. if it helps any i did notice that i was unable to reprogam the phone using *228. it still works rite now (i guess based on the previous OTA), but it wont reprogram...i get "programming unsuccessful". I'M running PRLs 38003 & 6499 in Charlotte N.C. any help would be greatly appreciated.
i have a motorola droid on metropcs help me please awwwwwww!!!!
yes my phone was flashed on metropcs its a motorola droid 2.1 android (rooted) an i was deleting some files on my sd card today cuz it was too full an my phone rebooted all the way to the begining i had to look for a wifi connection to sign in my google ACCOUNT to use my phone again an i lost my internet connection an mms messaging but my phone still can text an make calls but my internet an mms i gone please help me to get it back on thanks
somebody hit me up with the info
i need help with my phone i ned to put my mms on an internet back on i lost it when the phone reebooted but its still can text an call on metropcs android motorola droid 2.1 rooted
fredline12002 said:
is a broken link : (
Click to expand...
Click to collapse
not sure whats up with the link, just google a new how to root, sorry
Geniusdog254 said:
I get the phone failed error, but I don't see the NV Enabled option. Nor do I see the settings tab, where is that option?
Click to expand...
Click to collapse
when u open HV serial Port, its the second to last or maybe last tab,,, you cant miss it. this is where u make sure NV Enabled is NOT selected
Wolfdragon said:
ok, so im trying like hell to give this moto a shot. normally an htc fan. but the display, camera, and physical keyboard for the price was enticing. i did everything and got internet for a while. then i decided to load bugless' latest rom, now i have no web or mms. is there someting i have to redo??? knowing the norm with reflashes, i did the "open APNs" and redid everything there....but still no go. do i have to redo the Command prompts and the autostart download fr market?
*edit* did all the changes over...ALL. Still no web. if it helps any i did notice that i was unable to reprogam the phone using *228. it still works rite now (i guess based on the previous OTA), but it wont reprogram...i get "programming unsuccessful". I'M running PRLs 38003 & 6499 in Charlotte N.C. any help would be greatly appreciated.
Click to expand...
Click to collapse
If your on 2.1 bugless you need to redo allthe steps for fully working rom, maybe for 2.2 also i havent had to for a while, only bcuz i have cricket and roam off metro.
luvjones305 said:
yes my phone was flashed on metropcs its a motorola droid 2.1 android (rooted) an i was deleting some files on my sd card today cuz it was too full an my phone rebooted all the way to the begining i had to look for a wifi connection to sign in my google ACCOUNT to use my phone again an i lost my internet connection an mms messaging but my phone still can text an make calls but my internet an mms i gone please help me to get it back on thanks
Click to expand...
Click to collapse
you need to be more specific with wat u deleted?? which rom u ran? etc where did u get it flashed? most likey u went to a metro dealer, to get it flashed, METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around.
luvjones305 said:
i need help with my phone i ned to put my mms on an internet back on i lost it when the phone reebooted but its still can text an call on metropcs android motorola droid 2.1 rooted
Click to expand...
Click to collapse
what market are you in? who flashed your phone? quoted from above "METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around. "
Metro Fix Web/mms
"[/QUOTE] "METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around. "[/QUOTE]
For anyone having trouble with MMs/web on METRO please check out this thread. read from pg one if you dont know whats going on. or pick up here if you can perform the web/mms work around.
http://www.howardforums.com/showthread.php/1656326-Phones-and-more-info/page11
Grr
This is a great! Thank you for the instructions!
I am having one problum tho, and its very annyoing!!
When i first turn on my fone everything works internet+MMS+GPS+TXT+CALLS everything!
then when i recive or send a text or call (Anything that has to use 1X i think) I loose Internet+MMS and GPS
the only way it comes back is if i restart my fone!
dose anyone have any ideas? did i do somthing wrong? Please help.
I have a idea i know its possible on some phones to switch it so texts use 3G insted of 1x. Could i switch that on my droid?
Oh and im running bugless beast 2.2
good tutorial im just stuck at the step its written a little unclear im a moto newb unfortunately
""if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone""
i have downloaded cdma 2.7, nothing was stated about qpst in the necessary tools but i downloaded that too afterwards, and its not clear where i should go at this point after the initial reboot. are these directions for cdma2.7 or qpst? help???
................... bump
Hello sorry in advanced for the newbie question. My Moto Droid is already flashed to cricket. If I wanted to manually install 2.2 would I have to start with all steps or just from the 2.2 install?
iNFiNiTY125 said:
This is a great! Thank you for the instructions!
I am having one problum tho, and its very annyoing!!
When i first turn on my fone everything works internet+MMS+GPS+TXT+CALLS everything!
then when i recive or send a text or call (Anything that has to use 1X i think) I loose Internet+MMS and GPS
the only way it comes back is if i restart my fone!
dose anyone have any ideas? did i do somthing wrong? Please help.
I have a idea i know its possible on some phones to switch it so texts use 3G insted of 1x. Could i switch that on my droid?
Oh and im running bugless beast 2.2
Click to expand...
Click to collapse
from my understanding, cdma networks calls and text dont go through data connections, so when u place a call it will switch only to bars and no 1x/3g.
MMS and web will only work when not connected to a call ( i think thats what your stating??) ive never had a problem with data connection not coming back to phone after a call.... hopefully i answered your questions? and gps shouldnt be bothered at all that may be a rom issue. try a few roms other that bugless beast thats basically a stock ROM look into lithium mod or Chevyno1
tko1 said:
good tutorial im just stuck at the step its written a little unclear im a moto newb unfortunately
""if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone""
i have downloaded cdma 2.7, nothing was stated about qpst in the necessary tools but i downloaded that too afterwards, and its not clear where i should go at this point after the initial reboot. are these directions for cdma2.7 or qpst? help???
Click to expand...
Click to collapse
hello, lets see i believe this was originally the instructions to get the data working. so you needed QPST to enter in the passcode "cricket"....it just depends what rom you have. if you flash a rom and your data doesnt work then u will have to enter those settings in qpst. after entering those your data should work.
dortega2388 said:
Hello sorry in advanced for the newbie question. My Moto Droid is already flashed to cricket. If I wanted to manually install 2.2 would I have to start with all steps or just from the 2.2 install?
Click to expand...
Click to collapse
you should be fine with the NV items. after you flash 2.2 dial 611 (you may need to reflash PRL, and then from there i would give your phone about a 2minutes to see if any 1x/3g show up. if not commence with the instructions lol.
bigslanki said:
hello, lets see i believe this was originally the instructions to get the data working. so you needed QPST to enter in the passcode "cricket"....it just depends what rom you have. if you flash a rom and your data doesnt work then u will have to enter those settings in qpst. after entering those your data should work.
Click to expand...
Click to collapse
thanks for the reply, well i had all but given up on my droid dreams and i figured out on my own that they were QPST directions but were missing this important piece. QPST 2.7 WITH A OLDER BUILD LIKE 264 WILL NOT CONFIGURE THE DROID,IT GIVES AND ONLINE ERROR. YOU SHOULD USE AN UPDATED VERSION. I ENDED UP FINDING 2.7 BUILD 323.
Also. its unclear as to why in the adb commands we have
adb push c:\android\tools\autostart.sh /data/opt/autostart.sh
Now:
adb shell
it may be obvious to some but if Now: is an actual command it wouldnt work. so im assuming it isnt, and pretty much adb after that point is irreconcilable.
no matter what the droid never left the verizon network needless to say, and i havent recieved any input as to where i could have gone wrong, everything else was flawless up until the Now: part basically then i had to piece together adb. even tried without the now part and didnt succeed.
i did this and everything works. only problems is it 1x all the time; how to i get 3g?
I use:
Nexus S (i9023)
CyanogenMod 7.1
Radio I9023XXKB3
Problem:
At first I couldn't get 3G to work, I got stuck at EDGE.
So I tried to change the radio into an older one (KB3), then I could get the phone into UMTS, but everythime that happens, the GSM service would stop working (Emergency calls only). It will work again when it drops to GPRS/EDGE (I check this using *#*#4636#*#* - Phone Information)
I've tried to do a clean install, but the problem persists. So right now I must use GSM only setting from Phone Information.
Has anyone else had this problem and know a way to fix this?
Thank you
use kb1 radio its more stable on i9023 devices..
tell me if it works.. if it doesnt try reflashing your rom.. or switch to other roms.
After flashing KB1 radio, I think I'm back at getting stuck on EDGE again ^^;
Oh, and I cannot change "WCDMA only" to "GSM auto (PRL)". Everytime I choose "GSM auto (PRL)" it will revert back automatically to "WCDMA only".
EDIT: I just tried this method:
1. Use "Root Explorer" and navigate to /efs directory
2. Mount "R/W"
3. Cut these three files nv_data.bin , nv_data.bin.md5 and nv.log
4. Paste it at the ROOT of the SD Card.
5. Reboot your phone and you will have your 3G connection back.
(By alexwbaule)
Click to expand...
Click to collapse
And I just got 3G back! Yay!
I would back up those files.. Deleting/losing your EFS folder will mess you up later on.
Hi,
The system version is 5.7.906.XT862.Verizon.en.US
It was unlocked, rooted and installed root explorer ready to modify to work with US GSM ( Lycamobile also)
Here is where I got info to follow
http://forum.xda-developers.com/showthread.php?t=1989359
However, I have some concerns need help
1- will the instruction and the first build.prop file in the above link will work with my phone?
2- Can I use the phone with both pageplus ( being flashed with TalkForGood) and T-Mobile ( Lycamobile later)? I saw the same question without answer here http://forum.xda-developers.com/showthread.php?t=1425519
3- Can I use the phone oversea as a global phone without a need to follow the above link in Non-US GSM Networks session?
4- In case I want to go back stock image ( revert to the original one after messing it up), how?
To Skreelink, thank for your instruction but can you or anyone show me where to do the "required options" part because I simply couldn't find what you mentioned in my phone under Wireless & Network setting -> Mobile Network.
( I tried to post this under the above post but couldn't)
Thanks
macarong1 said:
Hi,
The system version is 5.7.906.XT862.Verizon.en.US
It was unlocked, rooted and installed root explorer ready to modify to work with US GSM ( Lycamobile also)
Here is where I got info to follow
http://forum.xda-developers.com/showthread.php?t=1989359
However, I have some concerns need help
1- will the instruction and the first build.prop file in the above link will work with my phone?
2- Can I use the phone with both pageplus ( being flashed with TalkForGood) and T-Mobile ( Lycamobile later)? I saw the same question without answer here http://forum.xda-developers.com/showthread.php?t=1425519
3- Can I use the phone oversea as a global phone without a need to follow the above link in Non-US GSM Networks session?
4- In case I want to go back stock image ( revert to the original one after messing it up), how?
To Skreelink, thank for your instruction but can you or anyone show me where to do the "required options" part because I simply couldn't find what you mentioned in my phone under Wireless & Network setting -> Mobile Network.
( I tried to post this under the above post but couldn't)
Thanks
Click to expand...
Click to collapse
1: The link you provided is my information and files for KEXEC ROMs, such as CM10.2 or AOKP. For the stock rom (As you listed 906), you will want to go here.
2: If you flash the XT883 radio for US GSM networks (like T-Mobile) you will not be able to flip between them via software toggle, you will have to flash the stock radio + swap build.prop back to stock and OTA on PagePlus, vice versa when you want to use the other network. (I wanted the same thing, I solved it by getting a Motorola Razr M XT907). The main reason for this is; The XT883 radio expects an RUIM card (CDMA version of SIM) and without it, puts it in emergency only mode. Verizon/PagePlus/Sprint/other US CDMA networks do not use the RUIM so no real way around this.
3: To use it as a global phone, just restore the stock radio and build.prop, it should work without issue WITHOUT MODIFICATION, as long as you have input the SIM unlock code to unlock the phone. You *can* use the XT883 radio globally, but both radios will work for global GSM.
4: To return to stock, follow this thread.
thank you
The best answer I have ever seen.
So if I buy Motorola Razr M XT907 to achieve the goal Pageplus/T-mobile, where is the best procedure I should follow?
Thank you very much.
McR
Help please
Skreelink said:
1: The link you provided is my information and files for KEXEC ROMs, such as CM10.2 or AOKP. For the stock rom (As you listed 906), you will want to go here.
Click to expand...
Click to collapse
I follow the above link to flash my Droid3 with the current stock image.
The flash was done then I rebooted the phone.
However, I was unable to replaced the build.prop file
I couldn't change its properties or owner or overwrite the file.
I see the instruction here http://forum.xda-developers.com/showthread.php?t=1406812&page=3
but I couldn't overwrite the original file with the modified one.
I rooted the phone already.
I am not sure what I did was wrong.
Please help.
Thanks,
macarong1 said:
I follow the above link to flash my Droid3 with the current stock image.
The flash was done then I rebooted the phone.
However, I was unable to replaced the build.prop file
I couldn't change its properties or owner or overwrite the file.
I see the instruction here http://forum.xda-developers.com/showthread.php?t=1406812&page=3
but I couldn't overwrite the original file with the modified one.
I rooted the phone already.
I am not sure what I did was wrong.
Please help.
Thanks,
Click to expand...
Click to collapse
You either have to use adb or a root browser. Rom Toolbox Lite has one, ES File explorer also has one. I'm sure other apps have a root browser, but I've not used others.Rom Toolbox's root browser allows you to longpress for a menu to change permissions.
Help please
Skreelink said:
You either have to use adb or a root browser. Rom Toolbox Lite has one, ES File explorer also has one. I'm sure other apps have a root browser, but I've not used others.Rom Toolbox's root browser allows you to longpress for a menu to change permissions.
Click to expand...
Click to collapse
Thank you for your fast reply.
I use totalcommander that run with superuser permission.
With a long press on the file, I go to property and set up with all permission ( 777)
After I hit OK to confirm the change, nothing happens but when I check again, it is still (rw-r--r--)
I have superuser installed.
I am stuck now.
Is there a way to browse and copy overwrite via windows or before the phone is up ( using usb cable)
Help please
macarong1 said:
Thank you for your fast reply.
I use totalcommander that run with superuser permission.
With a long press on the file, I go to property and set up with all permission ( 777)
After I hit OK to confirm the change, nothing happens but when I check again, it is still (rw-r--r--)
I have superuser installed.
I am stuck now.
Is there a way to browse and copy overwrite via windows or before the phone is up ( using usb cable)
Help please
Click to expand...
Click to collapse
If the permissions are not sticking, then the app you're using either does not have root privledges, is not performing correctly, or your root isn't correct. Try updating your superuser binary via the superuser app. Although, rw-r--r-- should be just fine, 777 would 'pose' a security threat since it would allow any app to modify it. Long as you replace it with the one required for GSM, rw-r--r-- permissions should work.
macarong1 said:
The best answer I have ever seen.
So if I buy Motorola Razr M XT907 to achieve the goal Pageplus/T-mobile, where is the best procedure I should follow?
Thank you very much.
McR
Click to expand...
Click to collapse
Sorry, didn't see this until now... getting the Razr M on pageplus is a real pain, though T-Mobile would be simple. It's a matter of getting the computer to read the diag port (you have to manually select the driver) and simply editing ONE NV-Item, then any GSM sim will work (AT&T, T-Mobile, etc).
Here is one of my posts with a quick guide about unlocking a razr m for gsm.
THANK YOU
Skreelink said:
You either have to use adb or a root browser. Rom Toolbox Lite has one, ES File explorer also has one. I'm sure other apps have a root browser, but I've not used others.Rom Toolbox's root browser allows you to longpress for a menu to change permissions.
Click to expand...
Click to collapse
I install Rom Toolbox Lite, it failed to verify root.
I check in SuperUser app and found a check mark "Temp Unroot"
I clear and run update for superuser.
Then I remove Rom ToolBox Lite and install again.
I then use Root browser from its link.
Each time it prompts permission of su.
I copy and paste sucessfully.
Reboot the phone and it work in T-Mobile NOW.
It WORKS now.
Thank you so much.
According to your answer in my first post, I can use this phone with GSM oversea without modification ?
Can you help on the link to the instruction of the phone model that can toggle between Pageplus/T-mobile.
I am much appreciated your help.
macarong1 said:
I install Rom Toolbox Lite, it failed to verify root.
I check in SuperUser app and found a check mark "Temp Unroot"
I clear and run update for superuser.
Then I remove Rom ToolBox Lite and install again.
I then use Root browser from its link.
Each time it prompts permission of su.
I copy and paste sucessfully.
Reboot the phone and it work in T-Mobile NOW.
It WORKS now.
Thank you so much.
According to your answer in my first post, I can use this phone with GSM oversea without modification ?
Can you help on the link to the instruction of the phone model that can toggle between Pageplus/T-mobile.
I am much appreciated your help.
Click to expand...
Click to collapse
The Droid 3 requires flashing the radio and build.prop to swap between CDMA/GSM
UNLESS it it is a foreign GSM network like Rogers in Canada, then the stock radio works without modification. The XT907 Razr M can do a software toggle between them (Network mode under Mobile Networks like the D3) but setting up PagePlus requires a lot of work for data, though GSM is a lot easier to get working than the D3. You can still go ahead and activate the D3 on pageplus, just after you flash between radios, you have to OTA program each time.
question for help
Skreelink said:
The Droid 3 requires flashing the radio and build.prop to swap between CDMA/GSM
UNLESS it it is a foreign GSM network like Rogers in Canada, then the stock radio works without modification. The XT907 Razr M can do a software toggle between them (Network mode under Mobile Networks like the D3) but setting up PagePlus requires a lot of work for data, though GSM is a lot easier to get working than the D3. You can still go ahead and activate the D3 on pageplus, just after you flash between radios, you have to OTA program each time.
Click to expand...
Click to collapse
Thank you.
I think I can do the same process with the image file from the original and overwrite the build.prop with original.
I did back up the build.prop but not the radio.img
Where can I find the Droid 3 radio.img of 906 version?
I want it simple as a reverting from what I did because I already removed all Verizon apps and install my apps in the current image.
A recovery task can bring back the original image.
** Oversea I meant is Vietnam
Thank again,
macarong1 said:
Thank you.
I think I can do the same process with the image file from the original and overwrite the build.prop with original.
I did back up the build.prop but not the radio.img
Where can I find the Droid 3 radio.img of 906 version?
I want it simple as a reverting from what I did because I already removed all Verizon apps and install my apps in the current image.
A recovery task can bring back the original image.
** Oversea I meant is Vietnam
Thank again,
Click to expand...
Click to collapse
I will see about uploading the stock radio when I get home.
THANK YOU
Skreelink said:
I will see about uploading the stock radio when I get home.
Click to expand...
Click to collapse
I am waiting.
Thank you sir ( my guess)
macarong1 said:
I am waiting.
Thank you sir ( my guess)
Click to expand...
Click to collapse
Sorry it took me so long, I had a long hectic day, but Here it is.
Just flash it like you did the XT883 radio and put a stock build.prop in (you should have backed up the original). Then you should be able to OTA program with *228 if it's activated on pageplus.
THANK YOU
Skreelink said:
Sorry it took me so long, I had a long hectic day, but Here it is.
Just flash it like you did the XT883 radio and put a stock build.prop in (you should have backed up the original). Then you should be able to OTA program with *228 if it's activated on pageplus.
Click to expand...
Click to collapse
I understand.
Thank you.
You are the best in my eyes
Hi, I would like to remove a Wi-Fi network from my list. It's listed as "not in range"
A long press then "forget" sequence returns "cannot forget".
After resetting the phone, the entry is unaffected.
How do I remove the entry (Z736563757265).
thanks nb
spice123 said:
Hi, I would like to remove a Wi-Fi network from my list. It's listed as "not in range"
A long press then "forget" sequence returns "cannot forget".
After resetting the phone, the entry is unaffected.
How do I remove the entry (Z736563757265).
thanks nb
Click to expand...
Click to collapse
Hey, I encountered the same issue (I have this exact SSID saved that cannot be forgotten, "failed to forget network" - where did this SSID come from????) and spent some time figuring out how to remove it. Well, I actually fixed it with the 'attwifi' network but I assume the following steps would apply for you too. I have an LG G2 running stock android 4.2, rooted. Note that you will need a rooted phone in order to do this. Here are the steps I took:
1.) Get a text editor capable of running as root (I used 920 text editor, there is a permissions issue with it though that I detail later).
2.) Open /data/misc/wifi/wpa_supplicant.conf using your text editor. Make a backup of this file while you're at it.
3.) Find the 'attwifi' entry and rename it (I renamed it to 'attwifi2'.) You could also probably remove the entry but I didn't try that.
4.) Turn off and turn on Wifi
* Note, I couldn't turn on wifi at first once I changed wpa_supplicant's conf file. It turned out to be a permission issue - my text editor did not save the file with the correct permissions. I had to run 'chmod 777 /data/misc/wifi/wpa_supplicant.conf' in a terminal window to give permissions back (it probably just needs chmod 666).
5.) Find 'attwifi2' in your saved wifi list and 'forget network'. It should now be forgetten. There is no more attwifi or attwifi2.
If this doesn't work for you, then you are probably using a different version of android where the conf file is in a different path. Try grepping for attwifi via a terminal window. Another thing you can try is to run 'dmesg' in a terminal window to see the system log - this could give you a clue as to what is going wrong. Best of luck!
Wifi issue on note2
I have a wifi issue, wifi I is not turning on after flashed the hd revolution on my note 2 pls help me
klaus ita said:
I have a wifi issue, wifi I is not turning on after flashed the hd revolution on my note 2 pls help me
Click to expand...
Click to collapse
I think your best bet is to ask your question in this thread: http://forum.xda-developers.com/showthread.php?t=2055736
Thanks!
Hello from SoCal
I'm mighty impressed with the custom roms I've come across on this amazing site, but after several frustrating days, I've decided to go back to stock firmware for my cdma moto g3, XT1548. (Huge props to lost101 for the detailed and easy-to-follow post.)
It's such a pleasure to extend the life and usability of an older phone by installing custom roms, and I've never had any problems until I bought the g3. But try as I might, no matter what rom I installed, I couldn't restore mobile data.
After installing the rom, it seemed easy enough to complete the final step and reset the carrier by inputting ##72786# via the generic phone app. But it never worked -- instead of going to the SCRTN settings, the dialer treated it like a phone call. I googled around for days, tried changing various settings -- no luck.
Actually, I did manage to upgrade from 5.1 to 6.0 by leaving TextNow for another Sprint mnvo, so it's not a total loss. Sure did like some of the 7.1.2 roms I installed for a bit, though . . .
Did I do something dumb, or is it the case that a certain set of conditions can limit a phone's ability to be upgraded? Any thoughts? Again, LOVE this website. Thanks!
OBTonyD said:
Hello from SoCal
I'm mighty impressed with the custom roms I've come across on this amazing site, but after several frustrating days, I've decided to go back to stock firmware for my cdma moto g3, XT1548. (Huge props to lost101 for the detailed and easy-to-follow post.)
It's such a pleasure to extend the life and usability of an older phone by installing custom roms, and I've never had any problems until I bought the g3. But try as I might, no matter what rom I installed, I couldn't restore mobile data.
After installing the rom, it seemed easy enough to complete the final step and reset the carrier by inputting ##72786# via the generic phone app. But it never worked -- instead of going to the SCRTN settings, the dialer treated it like a phone call. I googled around for days, tried changing various settings -- no luck.
Actually, I did manage to upgrade from 5.1 to 6.0 by leaving TextNow for another Sprint mnvo, so it's not a total loss. Sure did like some of the 7.1.2 roms I installed for a bit, though . . .
Did I do something dumb, or is it the case that a certain set of conditions can limit a phone's ability to be upgraded? Any thoughts? Again, LOVE this website. Thanks!
Click to expand...
Click to collapse
If you're using the Virgin mobile xt1548, you just need to set up the apn correctly. Use the one in the attachments. This how I do it.
1. Clean a flash ROM.
2. Mount /system in TWRP
3. Copy the apn-conf.xml with TWRP's file manager to /system/etc
4. Chmod the apn-conf.xml to 0644
5. Unmount /system and reboot.
6. Open settings and find the cellular network settings. Select the following.
Preferred network type>LTE
System select>Automatic
CDMA subscription>RUIM/SIM
Access Point Names>APN1 Virgin Internet LTE (if there is an APN2 delete it.)
After that select "carrier settings". You'll get an error, all radios will reset and LTE will show up in a few seconds.
For future reference do not use dialer codes on custom Roms for anything network related. This is asking for some serious headaches.
Spaceminer said:
If you're using the Virgin mobile xt1548, you just need to set up the apn correctly. Use the one in the attachments. This how I do it.
1. Clean a flash ROM.
2. Mount /system in TWRP
3. Copy the apn-conf.xml with TWRP's file manager to /system/etc
4. Chmod the apn-conf.xml to 0644
5. Unmount /system and reboot.
6. Open settings and find the cellular network settings. Select the following.
Preferred network type>LTE
System select>Automatic
CDMA subscription>RUIM/SIM
Access Point Names>APN1 Virgin Internet LTE (if there is an APN2 delete it.)
After that select "carrier settings". You'll get an error, all radios will reset and LTE will show up in a few seconds.
For future reference do not use dialer codes on custom Roms for anything network related. This is asking for some serious headaches.
Click to expand...
Click to collapse
Thanks for your post Winchester. I have Sprint, which is cdma. I understand editing the apn settings only works for gsm. I did try it anyway for kicks, no luck.
Oh and thanks for the heads-up about dialer codes on custom roms -- I had not heard that before.