Related
Hiya,
After dealing with a half-bricked Xoom, I did some research on this problem and found a solution.
If in any case, you happen to get stuck on the "Motorola Dual-Core Technology"
Solution to this (For the MZ604, One-Click rooted):
MZ604 Stock .imgs Download: http://developer.motorola.com/products/software/
*Make sure you have fastboot in the same directory as your adb for easy access*
1. Plug in your USB cord
2. Turn off your Xoom (Vol-Up + Power)
3. Boot into fastboot (Vol-Down + Power)
4. On your computer, open up a command prompt, and type the following:
Code:
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash userdata userdata.img
fastboot erase cache
fastboot oem lock
-or-
Code:
fastboot flash boot <path to boot.img>
fastboot flash system <path to system.img>
fastboot flash recovery <path torecovery.img>
fastboot flash userdata <path userdata.img>
fastboot erase cache
fastboot oem lock
5. Reboot the Xoom
Code:
fastboot reboot
6. There you go, back to stock!
On the real though, if you can get to Fastboot (or even the Moto "Android Recovery" state), you're not THAT bricked you've got to relock and go back to out-of-box; just keep a known-good boot.img around somewhere.
You just saved my life!
Thanks for sharing OP.
I take it this method is the same for 3.1?
I hope this works. Although, I can't turn my xoom off. It also appears that my computer will not recognize my device when it is plugged in. In addition, I can't turn off my Xoom? It just reboots... so I can't enter fastboot mode.
I just posted this in a new thread.
Lcsglvr said:
I tried reverting back to stock using the "one click" root/unroot tool that was the first to come out for the Xoom.
Anyway, I tried the unroot process and everything was going fine, until something occurred. Now, it tries to boot up and says at the Moto Dual Core Technology screen, "Failed to boot LNX 0x0004 // Starting RSD mode 2".
Can someone help
Click to expand...
Click to collapse
Can anyone help!
Lcsglvr said:
I hope this works. Although, I can't turn my xoom off. It also appears that my computer will not recognize my device when it is plugged in. In addition, I can't turn off my Xoom? It just reboots... so I can't enter fastboot mode.
I just posted this in a new thread.
Can anyone help!
Click to expand...
Click to collapse
same here, anyone help ((
Lcsglvr said:
I hope this works. Although, I can't turn my xoom off. It also appears that my computer will not recognize my device when it is plugged in. In addition, I can't turn off my Xoom? It just reboots... so I can't enter fastboot mode.
I just posted this in a new thread.
Can anyone help!
Click to expand...
Click to collapse
You can still enter fastboot if you xoom won't shut off. Just hold the appropria oncete buttons as it reboot. Happened to me last night upgrading to 3.1. It. Wouldn't shut down at all. Once I got into fastboot my computer saw it and I was able to fix
Honestly, I almost went through all of this last night when my WIFI Xoom got stuck in a boot loop.
However, I noticed that when my recovery went to flash the new 3.1 file, I felt like it didn't take as long as it should have. The file was the right size and all and it even said that everything installed successfully, but it just kept boot looping regardless of trying over and over. So I went ahead and re-downloaded the 3.1 file and repeated the steps to flash it and everything worked.
So, before you spend a whole lot of time restoring your Xoom, simply re-download the files and try it one more time. It worked for me.
rebill said:
You can still enter fastboot if you xoom won't shut off. Just hold the appropria oncete buttons as it reboot. Happened to me last night upgrading to 3.1. It. Wouldn't shut down at all. Once I got into fastboot my computer saw it and I was able to fix
Click to expand...
Click to collapse
Thanks! Finally have some hope to recovering. I'll post steps I took later once I get this damn thing fixed.
hmmm... I'm in fastboot supposedly and tried to flash boot.img but it seems to be stuck at <waiting for device>
This happen to anyone else?
After search seems like a driver issue, but I have installed the drivers... I was previous rooted, so I know I have the drivers. Just to be sure, I ran the MotoHelper again. I don't understand. It's just seeing my device on the "Starting Fastboot protocol support."
help?
Lcsglvr said:
hmmm... I'm in fastboot supposedly and tried to flash boot.img but it seems to be stuck at <waiting for device>
This happen to anyone else?
After search seems like a driver issue, but I have installed the drivers... I was previous rooted, so I know I have the drivers. Just to be sure, I ran the MotoHelper again. I don't understand. It's just seeing my device on the "Starting Fastboot protocol support."
help?
Click to expand...
Click to collapse
Yes. How did I fix it? I returned the xoom and had a new one two days later.
If the screen says something like "Entering RSD 2" then you're boned. The xoom won't be recognized in either the current state or in fastboot state by the computer, so no amount of commands will help. Even having the stock images doesn't help with that. Even RSDLite can't see the xoom in that state.
There have been several reports of people just being honest to Motorola and them fixing the device under the warranty.
Hmm honesty. I'll give it a shot.
Sent from my ADR6300 using XDA App
Is the final OEM lock necessary? It's quite a pain as your userdata gets wiped if you unlock it...
I was stuck on bootloop, with unrecognised device, through adb was able to get back into clockwork recovery somehow at first boot, think twice down volume? Could be wrong.
I was able tto rreflash zip 3.1 over thet top again.
sry if this is different and unhelpful, bu imagine things are pretty desperate if you are considering returning the device
zerin said:
Yes. How did I fix it? I returned the xoom and had a new one two days later.
If the screen says something like "Entering RSD 2" then you're boned. The xoom won't be recognized in either the current state or in fastboot state by the computer, so no amount of commands will help. Even having the stock images doesn't help with that. Even RSDLite can't see the xoom in that state.
There have been several reports of people just being honest to Motorola and them fixing the device under the warranty.
Click to expand...
Click to collapse
You're not boned at all. I had that happen to me so I just got back into fastboot, downloaded the files in the OP put ADB, Fastboot and the adb extensions into the file I downloaded then ran the commands and got me XOOM back up and running fine.
jbartcaps said:
You're not boned at all. I had that happen to me so I just got back into fastboot, downloaded the files in the OP put ADB, Fastboot and the adb extensions into the file I downloaded then ran the commands and got me XOOM back up and running fine.
Click to expand...
Click to collapse
You were likely in RSD 3, which is recognized by the computer. RSD 2 means adb and fastboot cannot see the device at all, so no flashing images is possible.
There's several states that all look very similar. Because some success was had with one doesn't mean it works for all. Motorola recognizes and is telling users that, in this state, the device needs to be sent back to them.
Can someone help us wifi xoom. Im stuck on the motorola screen and have a lil experience. I can fast boot reboot/fastboot device and it work but cant get the files from the hwi69 to fastboot on to it. I think im entering the commands wrong. Any advice would be appreciated
TheRedDroid said:
Hiya,
After dealing with a half-bricked Xoom, I did some research on this problem and found a solution.
If in any case, you happen to get stuck on the "Motorola Dual-Core Technology"
Solution to this (For the MZ604, One-Click rooted):
MZ604 Stock .imgs Download: http://developer.motorola.com/products/software/
*Make sure you have fastboot in the same directory as your adb for easy access*
1. Plug in your USB cord
2. Turn off your Xoom (Vol-Up + Power)
3. Boot into fastboot (Vol-Down + Power)
4. On your computer, open up a command prompt, and type the following:
Code:
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash userdata userdata.img
fastboot erase cache
fastboot oem lock
-or-
Code:
fastboot flash boot <path to boot.img>
fastboot flash system <path to system.img>
fastboot flash recovery <path torecovery.img>
fastboot flash userdata <path userdata.img>
fastboot erase cache
fastboot oem lock
5. Reboot the Xoom
Code:
fastboot reboot
6. There you go, back to stock!
Click to expand...
Click to collapse
Very good info to get into fastboot protocol:
Much thanks for the info. Worked like a champ. On an updated 3.2.1 XOOM I did an unlock, re-locked the wrong way, soft bricked, unbricked back to locked state. Finally followed your steps applied stock files and XOOM is re-locked and stock rocking back at 3.01. I needed to do all this to make sure I could get it back to stock in case it goes back to BB in 2 weeks. I was lucky enough to find one at a BB just not sure if I'll keep it. I plan on trying out some roms plus I heard Motorola is planning on doing an ICS push to the XOOM. ICS is very nice. It runs great on my unlocked Verizon G-Nex.. Again Thanks..
This post not only saved my half-bricked non-rooted Xoom, but also let me flash it from the Singapore firmware (bought if from Amazon, don't ask lol) to the regular USA firmware so that I can properly root it!
Thank you so very much!!
Rooting- error: cannot load "flashboot flash recovery r1-modaco-reco... .img"
I'm rooting my HTC One S the first time. And I was stupid and thought that HTC One X Clockworkmod flash would work.
Now I know how flashing and clockworkmod installing works but before that I accidentally flashed the One X command: "fastboot flash recovery recovery-clockwork-touch-5.8.2.7-endeavoru.img" and now when I go to recovery it gives me a red text and nothing works.
I searched everywhere for a guide to remove it and did not found. So I thought I could flash it over with an One S flash, but then when I entered the command: "fastboot flash recovery r1-modaco-recovery-clockwork-touch-ville.img" It gave me this: "error: cannot load 'recovery r1-modaco-recovery-clockwork-touch-ville.img'. My phone is connected perfectly, when I type 'fastboot devices' it shows me my phone is there.
So I think this is not a big problem for developers. Can anyone tell me what to flash or do to get rid of the One X recovery? Otherwise I just have to live with a phone with unlocked Bootloader and no access to root
Do you have the IMG I the directory from which you are running fast boot?
edscholl said:
Do you have the IMG I the directory from which you are running fast boot?
Click to expand...
Click to collapse
Ofcourse
rixrasta said:
Ofcourse
Click to expand...
Click to collapse
mabey I should just do a factory reset :/
Why don't you dl goo manager from market, open it and open menu and tap on Install OpenScriptRecovery and let it install twrp--although, I guess if you aren't rooted yet that won't work
Did you try fastbooting the cwmr from here--
http://www.clockworkmod.com/rommanager
Did you check the md5 on the modaco recovery before flashing
At the red text did you try hitting vol+ or vol- not sure which one takes you to stock recovery. What does red text say--
Did you hard reboot with holding down vol- and power at same time then release pwr after screen goes off and continue to hold vol-
Not sure what is wrong, just giving some ideas--
rugmankc said:
Why don't you dl goo manager from market, open it and open menu and tap on Install OpenScriptRecovery and let it install twrp--although, I guess if you aren't rooted yet that won't work
Did you try fastbooting the cwmr from here--
Did you check the md5 on the modaco recovery before flashing
At the red text did you try hitting vol+ or vol- not sure which one takes you to stock recovery. What does red text say--
Did you hard reboot with holding down vol- and power at same time then release pwr after screen goes off and continue to hold vol-
Not sure what is wrong, just giving some ideas--
Click to expand...
Click to collapse
Tyvm for your reply,
the cwmr for HTC One S does not exist any more on the page you gave me. There's only a blank page if you click on it
yes I did hard reboot and the red text says: This build is for development purposes only do not distribute outside HTC without HTC's written permission. Failure to comply my lead to legal action.
I tried the superboot from this site: htt p://w ww.m odaco.co m/to pic/352493-how-to-root-your-htc-one-s-for-windows-mac-and-linux/
This just brought up the recovery message again...
Then I tried flashing these files:h ttp://ww w.m odaco.c om/topic/353006-interim-clockworkmod-touch-recovery-for-the-htc-one-s-stock-download/
no help.
Any other ideas I should try?
However the flashing went through this time and there were no error, but the recovery is still f**ked.
rixrasta said:
Tyvm for your reply,
the cwmr for HTC One S does not exist any more on the page you gave me. There's only a blank page if you click on it
yes I did hard reboot and the red text says: This build is for development purposes only do not distribute outside HTC without HTC's written permission. Failure to comply my lead to legal action.
I tried the superboot from this site: htt p://w ww.m odaco.co m/to pic/352493-how-to-root-your-htc-one-s-for-windows-mac-and-linux/
This just brought up the recovery message again...
Then I tried flashing these files:h ttp://ww w.m odaco.c om/topic/353006-interim-clockworkmod-touch-recovery-for-the-htc-one-s-stock-download/
no help.
Any other ideas I should try?
However the flashing went through this time and there were no error, but the recovery is still f**ked.
Click to expand...
Click to collapse
Try this twrp .img
http://teamw.in/project/twrp2/100
The red text will stay till you relock, I believe, or flash stock recovery--
twrp recovery is the way to go. Me too I couldn't install the clockwork one!
rugmankc said:
Try this twrp .img
h ttp://team w. in/projec t/twrp 2/100
The red text will stay till you relock, I believe, or flash stock recovery--
Click to expand...
Click to collapse
I flashed the "openrecovery-twrp-2.2.2.0-ville.img". Didnnt change anything :/
sorry to hear that, not sure what else to do, so you still have onex recovery?
even if you run an ruu, i think you still have to flash the stock recovery first. haven't read up on that much, as never needed to run one
Don't know if trying to flash the stock recovery will help. I have the original one at home, but not sure if that is what they still call stock recovery with new ota's having come out
If it cannot load it, you probably spelt the name wrong. rename the image file to recovery.img (make sure it isn't .img.img) and flash that. Make sure the file path is correct! (e.g fastboot flash recovery C:\Users\Me\Desktop\recovery.img)
usaff22 said:
If it cannot load it, you probably spelt the name wrong. rename the image file to recovery.img (make sure it isn't .img.img) and flash that. Make sure the file path is correct! (e.g fastboot flash recovery C:\Users\Me\Desktop\recovery.img)
Click to expand...
Click to collapse
no no, the flashing finished successfully. I entered "fastboot flash recovery openrecovery-twrp-2.2.2.0-ville.img" and then it flashed without problems, but in the phone it didn't change a thing. If I enter recovery then there's the android icon with a white background and under it is the red text.
But keep guessing, maybe I really am doing something stupid wrong
When I go to Fastboot USB mode with my phone then I open the command prompt and firstly type "cd c:\CWM" (the folder where my flashing files are). Then secondly I type "fastboot devices" (just to be shure). And thirdly depending on what I am flashing I type "fastboot flash recovery name.img". I have tried "fastboot flash recovery openrecovery-twrp-2.2.2.0-ville.img", "fastboot flash recovery r2-modaco-recovery-clockwork-touch-ville" and "fastboot flash recovery ville_recovery_signed". Every one of them finishes successfully but doesn't change anything in the phone. I already have recovery-clockwork-touch-5.8.2.4-ville.zip and CWM-SuperSU-v0.96.zip in my phones directory to install root when I get into the recovery. In the C:\CWM folder in my computer are these files:
adb.exe
AdbWinApi.dll
AdbWinUsbApi.dll
fastboot.exe
(these where exctracted from fastboot.zip)
openrecovery-twrp-2.2.2.0-ville.img
r2-modaco-recovery-clockwork-touch-ville.img
ville_recovery_signed.img
the text won't disappear with unlocked bootloader, so that's ok.
Try to boot into bootloader hit fastboot reboot bootloader and then choose recovery. It can take a while to boot into recovery.
Gesendet von meinem HTC One S mit Tapatalk 2
stunner2002 said:
the text won't disappear with unlocked bootloader, so that's ok.
Try to boot into bootloader hit fastboot reboot bootloader and then choose recovery. It can take a while to boot into recovery.
Gesendet von meinem HTC One S mit Tapatalk 2
Click to expand...
Click to collapse
fastboot ->reboot bootloader ->bootloader ->recovery. Absolutely no change, It took half a second to bring up the "HTC quietly brilliant" logo and about two seconds for the red text to appear under it. No buttons work after that and I just have to hold the power button down to shut it down.
And by bootloader is unlocked!
As stunner said above it can take a while to boot into recovery, how long have you waited?
Give it a few minutes... Also you could try flashing stock recovery, it is distributed in the all-in-one tool and also in paulobriens posts about superboot. Then run a RUU.
But my best to would be to try fastboot booting a custom recovery, "fastboot boot cwm.img".
If this is the thing where you go int recovery for a millisecond and then back to the 'red text' screen (you have to watch carefully to notice), you should try erasing your cache in fastboot mode.
fastboot erase cache
Click to expand...
Click to collapse
-Jobo
It's gotten a little confusing and some suggestions are being repeated. I wonder if the android icon you are describing is the stock recovery symbol. At that screen have you tried to press vol+ or maybe volume-. I forget which one takes you to stock recovery. May want to check on that.
Also, have you tried typing "fastboot boot recovery" to go straight to recovery, bypassing htc restrictions
Here is very early stock recovery--not sure if it is still considered "stock" with new versions out now--I did mention that earlier--
https://www.dropbox.com/sh/yhrq0tia8512rj9/go28kc1NeP/ville_recovery_signed.img
I did have issues fastbooting recovery before. You can as mentioned try fastboot erase cache before fastbooting recovery. And change the name of your recovery to just recovery.img before you fastboot.
I assume you have nandroid backup on phone and copies of it and sdcard backup on pc.
I think when I had issues with recovery sticking it was my N1 and I typed "fastboot erase system" first, then fastbooted recovery. Then wiped all and restored nandroid. I am not sure we can do that on the 1s with no s-off. Someone else may know.
Can you access sdcard where you could reformat it fat32 thru a windows formatter program. Of course copy all to pc first. Sometimes sdcard formats help things you wouldn't expect it to.
Some folks have reported formatting works better thru phone on the 1s, maybe because it is an internal card. I did it once and think I had to redo it thru phone. But, if it gets recovery working, no big deal.
All these are suggestions and as the devs say--at your own risk--
I thought you said you said in first post, phone works, just no root capabilty. If that is true it should be fixable--I hope.
---------- Post added at 05:06 PM ---------- Previous post was at 04:32 PM ----------
rixrasta said:
no no, the flashing finished successfully. I entered "fastboot flash recovery openrecovery-twrp-2.2.2.0-ville.img" and then it flashed without problems, but in the phone it didn't change a thing. If I enter recovery then there's the android icon with a white background and under it is the red text.
But keep guessing, maybe I really am doing something stupid wrong
When I go to Fastboot USB mode with my phone then I open the command prompt and firstly type "cd c:\CWM" (the folder where my flashing files are). Then secondly I type "fastboot devices" (just to be shure). And thirdly depending on what I am flashing I type "fastboot flash recovery name.img". I have tried "fastboot flash recovery openrecovery-twrp-2.2.2.0-ville.img", "fastboot flash recovery r2-modaco-recovery-clockwork-touch-ville" and "fastboot flash recovery ville_recovery_signed". Every one of them finishes successfully but doesn't change anything in the phone. I already have recovery-clockwork-touch-5.8.2.4-ville.zip and CWM-SuperSU-v0.96.zip in my phones directory to install root when I get into the recovery. In the C:\CWM folder in my computer are these files:
adb.exe
AdbWinApi.dll
AdbWinUsbApi.dll
fastboot.exe
(these where exctracted from fastboot.zip)
openrecovery-twrp-2.2.2.0-ville.img
r2-modaco-recovery-clockwork-touch-ville.img
ville_recovery_signed.img
Click to expand...
Click to collapse
you should also have adb.exe if you are using adb--
frdd said:
As stunner said above it can take a while to boot into recovery, how long have you waited?
Give it a few minutes... Also you could try flashing stock recovery, it is distributed in the all-in-one tool and also in paulobriens posts about superboot. Then run a RUU.
But my best to would be to try fastboot booting a custom recovery, "fastboot boot cwm.img".
Click to expand...
Click to collapse
Okay I waited for 10 minutes, nothing happens. I've even tried to hold down all the button combinations(with the three buttons) for a few minutes.
I've tried flashing everything and fastboot boot just takes me directly to the recovery with the red text. I flashed both the recoveries in the all-in-one tool.
As I know absolutely nothing about RUU(only what the letters stand for) then I'd rather not do that because I read from some threads that RUU has quite a high chance to mess up your phone. Or if you direct me to a tutorial that u insure me that is 100% good then I could give it a go : D
[
I think I have made the same mistake of flash recovery, but I can not get into cwm recovery, I only appear for 1 second the recovery, then restarts and returns to the operating system. SD card, all changes are discarded when you restart the phone, which is also only if I try to install or remove some utility. Can not install any recovery, even if fastboot works well and looks real mind install the recovery but when I reboot, it returns to its previous behavior, with recovery not working. I tried to install the recovery in every way, from fastboot, from All in one with quickroot, but none of these operations has changed the state of the system.
Unfortunately you can not install a Stock RUU because the bootloader unlocked and the recovery is not the stock, and especially not when there is no tutorial to follow to bring this situation to the ONE S, to its original state
Hopefully someone will be able to find a solution to your and my problem.
One option you guys may need to entertain, if applicable, would be to exchange phones with Carrier. Worth a shot--
I have not heard of this exact issue, but most comments say if you can't boot to recovery you are bricked--
Has anyone tried "fastboot boot recovery" command in terminal window?
I have 2 Xoom tablets, in Germany, and I took the SD Card from one of them to put it on a new phone, the Tablet kept working fine until last week that I forgot to plug it and the battery ran out. When I charged it and started it, it didn´t work again, I got the Encryption message, nothing happens when I click the Reset Tablet either, I tried putting the SD card from my other Xoom but still nothing. I enter the Recovery mode and did a Factory Reset and the tablet was OK.
Battery run out again yesterday and got the same problem once again, but now factory reset is not working, tablet stays stuck at the "M" logo after doing it, I have repeat the operation a zillion times and nothing, it stays on the M. Plus I can´t turn it off either.
The model is the MZ604 and Android Version 4.0.4
I connected the xoom to the computer after installing the drives but it won´t recognize it. I got to do the fastboot and flashed motorolas images but nothing. I can´t do the adb reboot bootloader command because ADB won´t work, because I don´t have USB Debbuging checked, but I can´t check it now because I can´t get to settings (
What can I do to recover the tablet?
Anyone, is driving me crazy, no matter how many time I flash new images it always stays on the original, so I can´t flash any special recoveries either
I tried RDS too and after the reboot stays the same in the M logo, nothing changes. What can I do?
No ideas? :crying:
I want to save the tablet if possible.
Hi, could you explain exactly what you've tried?
In particular what you mean by "I got to do the fastboot and flashed motorolas images but nothing." and "no matter how many time I flash new images it always stays on the original, so I can´t flash any special recoveries either"
By flashed Motorola's images do you mean you flashed the stock images?
And when you say you flash new images but it always stays on the original, I assume you mean the recovery stays as Xoom default?
Let me know and I'll see if I can help.
alecbond said:
Hi, could you explain exactly what you've tried?
In particular what you mean by "I got to do the fastboot and flashed motorolas images but nothing." and "no matter how many time I flash new images it always stays on the original, so I can´t flash any special recoveries either"
By flashed Motorola's images do you mean you flashed the stock images?
And when you say you flash new images but it always stays on the original, I assume you mean the recovery stays as Xoom default?
Let me know and I'll see if I can help.
Click to expand...
Click to collapse
Yes I mean stock images, and yes, it always stays on Xoom default, it never changes no matter which Recovery image I flash.
The recovery is likely reverting to default because the Xoom does this automatically each boot.
We might be able to give you a recovery that stays put but the booting issue may or may not be something worse.
Being able to fix the recovery in place is reliant on adb working from recovery itself, which I'm unsure is possible.
Whilst you seem to have reasonable knowledge of flashing and using adb/fastbbot, I'll give full instructions.
I assume you have the necessary files for fastboot so I'll skip that.
Place your chosen recovery image in your fastboot folder. (I recommend ClockworkMod Touch recovery from here)
Hold shift and right click the folder containing your recovery image and fastboot files, then select 'open command prompt here'
Your PC is now setup for the fastboot process.
Connect your Xoom to your PC.
Power on your Xoom and once you see the Motorola logo, wait about 3 seconds, and press volume down.
The screen should show the Motorola logo in the center and '--> Android Recovery' in the top left.
Press volume down twice more until the top left says fastboot then press volume up.
The screen will say 'Starting Fastboot protocol support'
Now on your PC, in command prompt run the following:
fastboot flash recovery xxxx.img
Rename xxxx.img to whatever your recovery .img file is namedOnce verified, reboot by holding Volume up and Power. (Keep connected to PC and keep command prompt open)
Again, when you see the Motorola logo wait about 3 seconds and hit volume down. You should see 'Android Recovery' in the top left corner, now press volume up to enter recovery, you should now see your flashed recovery.
This is where I'm unsure. Try running the following:
adb remount
adb shell mv /system/recovery-from-boot.p /system/recovery-from-boot.p.old
adb shell mv /system/etc/install-recovery.sh /system/etc/install-recovery.sh.oldIf you are able to run this, this will rename the files that are reverting the recovery to default and prevent it happening again. If not, we can go ahead with attempting to flash stock images anyway.
To flash stock images download Build H.6.2-24 for Retail Europe (found here.)
Extract the files to your fastboot folder.
Again, reboot your Xoom, either by holding volume up and power, or from recovery.
And again, after about 3 seconds press volume down 3 times until the top left says '--> Fastboot' then press volume up.
Now run the following from command prompt:
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash userdata userdata.img
fastboot erase cache
fastboot oem lockThis will wipe all data on the Xoom, and hopefully reset it to stock.
Finally, run:
fastboot rebootand you should boot into Android 3.2(?), fingers crossed.
If you require further clarification or help let me know.
alecbond said:
The recovery is likely reverting to default because the Xoom does this automatically each boot.
We might be able to give you a recovery that stays put but the booting issue may or may not be something worse.
Being able to fix the recovery in place is reliant on adb working from recovery itself, which I'm unsure is possible.
Whilst you seem to have reasonable knowledge of flashing and using adb/fastbbot, I'll give full instructions.
I assume you have the necessary files for fastboot so I'll skip that.
Place your chosen recovery image in your fastboot folder. (I recommend ClockworkMod Touch recovery from here)
Hold shift and right click the folder containing your recovery image and fastboot files, then select 'open command prompt here'
Your PC is now setup for the fastboot process.
Connect your Xoom to your PC.
Power on your Xoom and once you see the Motorola logo, wait about 3 seconds, and press volume down.
The screen should show the Motorola logo in the center and '--> Android Recovery' in the top left.
Press volume down twice more until the top left says fastboot then press volume up.
The screen will say 'Starting Fastboot protocol support'
Now on your PC, in command prompt run the following:
fastboot flash recovery xxxx.img
Rename xxxx.img to whatever your recovery .img file is namedOnce verified, reboot by holding Volume up and Power. (Keep connected to PC and keep command prompt open)
Again, when you see the Motorola logo wait about 3 seconds and hit volume down. You should see 'Android Recovery' in the top left corner, now press volume up to enter recovery, you should now see your flashed recovery.
This is where I'm unsure. Try running the following:
adb remount
adb shell mv /system/recovery-from-boot.p /system/recovery-from-boot.p.old
adb shell mv /system/etc/install-recovery.sh /system/etc/install-recovery.sh.oldIf you are able to run this, this will rename the files that are reverting the recovery to default and prevent it happening again. If not, we can go ahead with attempting to flash stock images anyway.
To flash stock images download Build H.6.2-24 for Retail Europe (found here.)
Extract the files to your fastboot folder.
Again, reboot your Xoom, either by holding volume up and power, or from recovery.
And again, after about 3 seconds press volume down 3 times until the top left says '--> Fastboot' then press volume up.
Now run the following from command prompt:
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash userdata userdata.img
fastboot erase cache
fastboot oem lockThis will wipe all data on the Xoom, and hopefully reset it to stock.
Finally, run:
fastboot rebootand you should boot into Android 3.2(?), fingers crossed.
If you require further clarification or help let me know.
Click to expand...
Click to collapse
Thanks for the info, sadly I have done almost all that, I can´t use adb commands because I never allowed the tablet to do USB Debbuging, since I wasn´t doing anything that needed that and never thought I would need it. I think I didn´t kept the tablet connected to the PC, so I will try again and let you know if it works.
Like I said before, I'm unsure whether it'll work as I'm not an expert.
However, you may find this helps:
Whilst in recovery and connected to your PC, open Device Manager, find your Xoom, usually under 'Other devices'.
Then right click on your Xoom > Update driver software... > Browse my computer for driver software > Let me pick from a list of device drivers on my computer > Pick your Xoom (either one if there's two shown)
Windows should confirm the driver installed then adb should work in recovery.
I believe ClockworkMod Recovery enables USB debugging anyway, through modifying default.prop
I'd recommend trying the above, and/or if that fails for any reason download Motorola USB Drivers here.
Thanks again but nothing works, I tried rebooting being connected to the PC and the same thing happens, the default recovery from the Xoom stays there, fastboot shows on the command Prompt and in the tablet that everything went ok and the new image was flashed but the rebooting kills it, and I can´t use any ADB commands because of the stupid USB Debugging, if something like this can happen, Motorola should have left it open from default or at least have a fail safe in case something like this could happen. RDS also flashes an image but when it rebbots the whole thing goes to hell, it stays on the damn logo with the same images. I think I can throw the tablet to the trash :crying:
Unless its a serious hardware issue, I wouldn't trash it! It clearly has life as you're able to successfully flash and such.
I'd recommend having a look at the FAQ.
alecbond said:
Unless its a serious hardware issue, I wouldn't trash it! It clearly has life as you're able to successfully flash and such.
I'd recommend having a look at the FAQ.
Click to expand...
Click to collapse
Thanks, but I have done everything, what is the good thing of a successful flash when the tablet returns to it´s previous state as soon as it reboots?
Plus I can´t use one of the most important things, adb, because of the usb debugging, I can´t get into the tablet to activated it, and even if there are recoveries which bypass this thing, I can´t flash them into the tablet, well I can, they just aren´t there after the reboot. And all this because the tablet run out of battery :crying:
ClockworkMod recovery itself allows the use of adb regardless of USB debugging setting.
I believe the command adb remount should allow it.
If adb is denied you can try what I said earlier
Whilst in recovery and connected to your PC, open Device Manager, find your Xoom, usually under 'Other devices'.
Then right click on your Xoom > Update driver software... > Browse my computer for driver software > Let me pick from a list of device drivers on my computer > Pick your Xoom (either one if there's two shown)
Windows should confirm the driver installed then adb should work in recovery.
Click to expand...
Click to collapse
alecbond said:
ClockworkMod recovery itself allows the use of adb regardless of USB debugging setting.
I believe the command adb remount should allow it.
If adb is denied you can try what I said earlier
Click to expand...
Click to collapse
The problem lies with the recovery, I only have the default recovery from the xoom, it doesn´t matter how many times I flash it and everything seems to work correctly, when I restart the tablet I get the default recovery. I don´t understand why this happens, command prompt and the tablet in fastboot mode tell me the recovery has been flashed, but to use it I have to reboot and when I do I always find the same good for nothing recovery.
recovery
Hello,
I don't really understand your problem with the recovery ?
When you flash a custom recovery with fast boot, you restart the tab and after 2 or 3 second you see the Motorola Logo you push the volume down
and volume up button to enter in the new recovery.
If you flash custom recovery but restart completely the TAB without manually enter in the custom recovery, each time you retrieve the original recovery.
pots22 said:
Hello,
I don't really understand your problem with the recovery ?
When you flash a custom recovery with fast boot, you restart the tab and after 2 or 3 second you see the Motorola Logo you push the volume down
and volume up button to enter in the new recovery.
If you flash custom recovery but restart completely the TAB without manually enter in the custom recovery, each time you retrieve the original recovery.
Click to expand...
Click to collapse
Here is what happens, I flash new recovery, I restart the xoom with power and volume up, when the logo appears, after 3 seconds, I push volume down, recovery option shows, I press volume up and the default recovery is still there, not the new one I just flashed.
Is really no one out there that can help? :crying:
There's nowhere stated that, however I believe you already have unlocked your bootloader, didn't you? Because it's REALLY weird that it can't flash the recovery, I mean, you left the battery run out, then after charging you wasn't able to boot normally again.
I'll think a little, but give a check if your bootloader is really unlocked, the device should have installed the recovery, and as you didn't restart it entirely (let it go after the dual core logo), the recovery should be there...
"We think so supersonic and we make our bombs atomic" - Eagle Fly Free (Helloween)
Sent from my Nexus 10 using Tapatalk HD
I have done the fastboot oem unlock command, should I do it everytime? I can´t use adb, because like I said, I never check the USB Debugging, which I have done in my other tablet now, don´t want the same thing to happen twice.
is it dead?
hgokuh said:
is it dead?
Click to expand...
Click to collapse
I unfortunately believe that yes, however I'm still thinking about it! So don't give up! As soon as I have another answer I shall post something
"We think so supersonic and we make our bombs atomic" - Eagle Fly Free (Helloween)
Sent from my Nexus 10 using Tapatalk HD
Hello everyone. I am new around here and totally new with android devices. I got my tf300t, installed twrp and flashed to the newest android version. Then my dad suddendly pressed something like restore to the manufactory setting and after that it rebooted and just keep booting with teamwin logo. I can not access twrp recovery mod, it is just in boot loop. I managed to get adb to work, but no fastboot since it does not boot into recovery mode. When I am in adb I can browse the device but the adb reboot bootloader does not work at all. It just hangs there. I can not power off the device because it does not let me, I can not boot into recovery mode with powerbutton and volume down button. After a long power button press it only reboots. I even tried with hard reset button but still the same. Could You please help me somehow? I really need that device for school and I would like to get back into the stock android. Thank you so much for any help.
//edit : I also forget to mention, when I execute adb deviced it shows:
List of devices attached
0123456789ABCDEF recovery
Also the device is unlocked.
Did you tried: adb reboot recovery ?
Did you tried to flash recovery again?
Be sure to use the right recovery for your bootloader. Did you upgraded bootloader to latest ASUS one? One then you're able to flash current recoveries like TWRP like 2.8.5.0 oder 2.8.7.0.
Edit: Also take a look here -> http://droidmodderx.com/prime/?page_id=74
Hello sir. Thank you for answering. I tried adb reboot recovery and it just hangs to be executed... But the tablet is still flashing the teamwin logo. I have the same bootloop as the guy on youtube called Francis Domingo and video called Samsung s5 stuck at TWRP Recovery boot loop (unfortunately I can not add link here).
//edit: Thank you for the link. It look like I have to use option 1a. Is it safe to use that command and I will not make it even more bricked? Thank you so much
//edit2: Now I just realized how to turn off the device to stop from rebooting. I just long pressed power button and up volume button and after the screen went black I kept holding the up volume button. I didn't work with down volume button or if I stopped holding the up volume button after black screen it rebooted again.
//edit3 : Let's say if I get to the twrp mode with option 1a from the link, what do I have to do next to get back to the stock rom (I think it was something like 4.0.3) ? Thank you
What the guy does in 1a is wiping mmcblk0p3.
Afaik mmcblk0p3 is the staging partition. That would be my guess anyway if you had access to fastboot. Usally when you can't boot into recovery, something is wrong in staging. I got the same problem 2 days ago. In this case you usually wipe staging partition via fastboot.
Since you got no fastboot access, you have to try with adb.
After cleaning the staging partition you can flash any recovery you want back again.
The recovery must be flashed to mmcblk0p4 <- 4!!! is the recovery partition. (but you should wipe mmcblk0p3 (3!!!) before)
So I would say, try what solution 1a suggests.
Edit: You can go back to stock android if you want, but there is no reason for this. My advice would be to unlock and root your device, upgrade to latest boot loader (which is done by upgrading to latest stock rom), then flash TWRP 2.8.5.0 and then a useful ROM on top. I'm using the one from timduru which is very nice. You can find it here: http://forum.xda-developers.com/transformer-tf300t/development/rom-t2932783
Thank you for the answer. Could you please write a step by step to get out of brick and to get the stock version, because the newer one I installed was many times slower. The reason why I would like to have step by step is because I don't wanna mess it even more than it is. Thank you so much.
//the stock rom was much more faster than the one I have installed, I mean... the boot time wad unbelievable slow, same with responses and wifi problem. If there is any other faster rom than stock I would be happy but I don't wanna mess with any bugs or slow boot speed and I can not wait minutes until it boots.
Hm, try the Option 1a from the link.
If done, boot into current recovery. Tell me which version and which recovery do you have.
Top on this we can decide what to do to flash a good ROM.
I had the exact same thing happen to me yesterday. Option #1 worked for me.
I did the steps from option #1 and powered down using the volume up + power. I then tried to boot into TWRP recovery, which only reproduced the same issue.
I redid the option #1 steps, and this time powered down using the power + volume down. I powered back up normally, and it rebooted normally into the ROM.
The tablet now works normally, and I can also boot back into TWRP recovery with no issues.
Thanks for the thread and the link.
Thank you so much Catscratch! After I executed both command from option 1a I can get into the screen, where it shows three options: RCK, Android, Wipe Data
In the top left corner, there is written:
Key driver not found.. Booting OS
Android cardhu-user bootloader <1.00 e> released by "WW_epad-10.6.1.27.5-20130902" A03
Starting Fastboot USB download protocol
The tablet can boot into the last ROM but as I said, I would like to have the faster and less buggy rom than this. When I open the settings and click about button there is written: CyanongenMod: 12.1-20150814-NIGHTLY-tf300t and Android version 5.1.1.
If I start RCK it just brings me back to the loop, but now I have fastboot available as it said above and I can list the fastboot devices on computer, which I couldn't before. Should I just execute this command from the computer "fastboot -i 0x0B05 flash system blob" and then "fastboot reboot" or should I download ROM from asus.com/Tablets/ASUS_Transformer_Pad_TF300T/HelpDesk_Download/ -> OS Android -> Firmware and now I don't know which should I choose: If JP or CN or WW or US or TW (Probably US right?). After that should I execute "fastboot -i 0x0B05 flash recovery firmware.img" and then "fastboot reboot" ? Or which ROM should I download to make it even faster and less buggy than stock ROM? Thank you so much again, You saved my tablet
//After I unzipped downloaded US ROM there is no img file. If I remember right the img file is only recovery to reflash the actual one and then when I start the twrp recovery I will select zip file with rom right?
OK, first of all to continue...I assume you got root access. (I think you should have, because you already got CM installed)
Next. Downloads.
Download: https://twrp.me/devices/asusTF300T.html
Also Download ROM+SuperSU: http://forum.xda-developers.com/transformer-tf300t/development/rom-t2932783
And GApps: http://forum.xda-developers.com/android/software/app-minimal-gapps-gapps-lp-20150107-1-t2997368
Push all files to sdcard with "adp push" or in CM. Like you want.
Flash TWRP. (you can skip this step if you already got TWRP 2.8.5.0 or higher version). You don't need latest one.
fastboot -i 0x0b05 flash recovery twrp.img
fastboot reboot
- or -
adb reboot recovery
Now, go into recovery and wipe everything:
- cache
- dalvik
- system
- data
After that flash ZIPs from sdcard. (use "add more zips" option)
1. ROM
2. Gapps
3. SuperSU
Next: Wipe cache and dalvik again (only these two).
Reboot and wait. First boot can take some minutes.
Thank you so much again. Everything work perfectly The rom looks a lot faster than the older one I had there. No issues yet at all. Just awesome. Thank you so much. Really appreciate your kindness and help. You have a nice day !
Thanks. Have fun with your tf300.
I haven't really touched this tablet in a while, but i wanted to start using it again. I was running BlissPop. It was slow, and kept giving me an error when it was trying to update, so I decided to try a different ROM. So I downloaded the lineageOS ROM and tried to flash it.
However, TWRP kept giving me an error when I tried to flash the ROM. I don't remember exactly what the error was.
So, I thought that I needed to update TWRP. I tried through the "Official TWRP" app, but after doing so I was unable to boot into recovery mode at all. I could still get to the bootloader, but when I tried to select recovery mode it would give me an error and dump me back out to the bootloader menu.
I tried installing twrp through "TWRP Manager" app, but it just says "something went wrong"
I tried doing this using ADB. I connected the tablet, enabled USB debugging. If i do the ">adb devices" command, I can see the tablet. Then I did >adb reboot bootloader - which works, it reboots the device into the bootloader. But then I try and flash recovery and nothing happens, it just says <waiting for device>. And if I do > fastboot devices it doesn't list any devices.
If I reboot to the bootloader and select "Recovery Mode' i just get the nvidia boot logo and it stays there forever.
I don't know what else to try at this point.
I think I could get this to work if I could just get fastboot to recognize my device, but I'm not sure what's preventing that from happening.
mattlokk said:
I haven't really touched this tablet in a while, but i wanted to start using it again. I was running BlissPop. It was slow, and kept giving me an error when it was trying to update, so I decided to try a different ROM. So I downloaded the lineageOS ROM and tried to flash it.
However, TWRP kept giving me an error when I tried to flash the ROM. I don't remember exactly what the error was.
So, I thought that I needed to update TWRP. I tried through the "Official TWRP" app, but after doing so I was unable to boot into recovery mode at all. I could still get to the bootloader, but when I tried to select recovery mode it would give me an error and dump me back out to the bootloader menu.
I tried installing twrp through "TWRP Manager" app, but it just says "something went wrong"
I tried doing this using ADB. I connected the tablet, enabled USB debugging. If i do the ">adb devices" command, I can see the tablet. Then I did >adb reboot bootloader - which works, it reboots the device into the bootloader. But then I try and flash recovery and nothing happens, it just says <waiting for device>. And if I do > fastboot devices it doesn't list any devices.
If I reboot to the bootloader and select "Recovery Mode' i just get the nvidia boot logo and it stays there forever.
I don't know what else to try at this point.
I think I could get this to work if I could just get fastboot to recognize my device, but I'm not sure what's preventing that from happening.
Click to expand...
Click to collapse
Did you set:
Allow oem unlock in dev opt.
Fastboot protocol into BL?
Twrp app & manager need root to work.
Just flash the latest stock ROM first, lineageos requires having latest firmware.
I wrote a little guide not long ago about that (obviously, you can skip the F2FS steps if you don't need F2FS and just flash ROM after flashing latest TWRP)
Link
thanks for the help, i'll try and work through this soon.
fpozar said:
Just flash the latest stock ROM first, lineageos requires having latest firmware.
I wrote a little guide not long ago about that (obviously, you can skip the F2FS steps if you don't need F2FS and just flash ROM after flashing latest TWRP)
Link
Click to expand...
Click to collapse
I had seen your thread, and was intending on following it. nice post. 2 quick questions though
1) this is a shield tablet that was supposed to be remotely bricked by nvidia after the warranty claim. Will that happen if I flash the official recovery ROM?
2) how would I even flash that rom if I can't get recovery mode to work in trwp?
I think the root problem that I'm having is that I can't seem to connect to the device via fastboot (i'm sure i used the wrong terminology somehow)
edit: well I downloaded the USB driver for the shield tablet from nvidia, and i was able to install that (rather than the google usb driver). Fastboot finally recognized my device after that. I'm trying to flash the recovery now, but it doesn't seem to be doing anything, just been stuck on this screen for a while now: https://i.imgur.com/BUwj3Hx.png guess I'll continue to wait a while.
edit 2: well, finally got TWRP to flash over fastboot (https://i.imgur.com/tV1DqDv.png) however I still can't enter recovery mode. I just get the nvidia boot logo and then nothing happens. TWRP manager still says i don't have it installed either.
i'm about ready to give up on this... i've spent like 6 hours on this crap already and I feel like I keep getting further away from it.
mattlokk said:
I had seen your thread, and was intending on following it. nice post. 2 quick questions though
1) this is a shield tablet that was supposed to be remotely bricked by nvidia after the warranty claim. Will that happen if I flash the official recovery ROM?
2) how would I even flash that rom if I can't get recovery mode to work in trwp?
I think the root problem that I'm having is that I can't seem to connect to the device via fastboot (i'm sure i used the wrong terminology somehow)
edit: well I downloaded the USB driver for the shield tablet from nvidia, and i was able to install that (rather than the google usb driver). Fastboot finally recognized my device after that. I'm trying to flash the recovery now, but it doesn't seem to be doing anything, just been stuck on this screen for a while now: https://i.imgur.com/BUwj3Hx.png guess I'll continue to wait a while.
edit 2: well, finally got TWRP to flash over fastboot (https://i.imgur.com/tV1DqDv.png) however I still can't enter recovery mode. I just get the nvidia boot logo and then nothing happens. TWRP manager still says i don't have it installed either.
i'm about ready to give up on this... i've spent like 6 hours on this crap already and I feel like I keep getting further away from it.
Click to expand...
Click to collapse
Okay so I'm guessing you have stock ROM.
To flash TWRP you have to enter fastboot mode (vol down + power I believe) and flash the twrp image with fastboot flash recovery twrp.img (rename the shield tablet twrp to just twrp.img and place it into your easy adb and fastboot folder)
And DON'T reboot into OS, rather use your volume buttons to navigate to "restart to recovery" or just use hardware keys again directly from TWRP (vol up + power).
Good luck
fpozar said:
And DON'T reboot into OS, rather use your volume buttons to navigate to "restart to recovery" or just use hardware keys again directly from TWRP (vol up + power).
Good luck
Click to expand...
Click to collapse
Agreed. This is probably what is happening (as described on the TWRP webpage here:
Note many devices will replace your custom recovery automatically during first boot. To prevent this, use Google to find the proper key combo to enter recovery. After typing fastboot reboot, hold the key combo and boot to TWRP. Once TWRP is booted, TWRP will patch the stock ROM to prevent the stock ROM from replacing TWRP. If you don't follow this step, you will have to repeat the install.
Alternately, immediately rooting (flash SuperSU or Magisk) right after flashing TWRP, will prevent TWRP from being replaced with stock recovery.
Although the inconsistent fastboot connection, and how much trouble you had flashing TWRP initially, is a bit worrisome. Try using a different cable (maybe the one you are using is not connecting well?) try another USB port on the computer, and don't use a USB hub (connect direct to the PC).
Well, like they say: persistence is key. I kept pushing and trying new things until eventually.... I bricked the device. No, not really, it's working great now on LineageOS.
Thanks again to everyone who helped me out :good:. I'm still not sure exactly what caused TWRP to stop working on my device, however following this guide helped me fix it: https://forum.xda-developers.com/shield-tablet/help/help-stuck-nvidia-boot-screen-t3076462
The "flash-all.bat" restored everything to stock (including the recovery mode) and after that I was able to flash the latest TWRP and install Lineage.