Hiya peeps well i am new at this so am not a out blown expert i did a lot of research and i could not find some answer to some wanted question on radio and stuff like that now where i should start
ok i had my treo 750 to att 2.25 and wm 6.1 and i wanted it unbranded to 2.27 so i followed the instruction and i tried to do the radio up date using cheetah but i most have did something not right, for this part i got one question
using a sim card in the network setting for band should it work on auto or its normal that i need to specified what band am using? or i did something to my radio? (and not talking what tower it should connect to that automatic am talking between gsm and umts since am on telus that uses bell/telus shared tower that on UMTS 850 / UMTS 1900 network code of 302880 since i did that at lease it said the right provider and its no longer disconnecting me or saying no service)
if i update my radio should i use from this site?
www crc.id.au/files/xda/Radio_Roms
if yes what version that is safely work with unbranded 2.27 and wm 6.1
if no then where i can find the right radio rom i can grab for my treo 750 and instruction how to install it lol
am trying to understand how the phone should be setup while using a sim card without any disconnection by the phone also gime ability of roaming as well since i like my phone to be able too for future use
anyway thanks for reading and really do hope someone reply
also P.S: about the roaming icon any solution to that?
When you flash an OS ROM, it doesn't change the radio ROM. You have to flash it seperately.
I would suggest you only use the most recent radio ROM for your provider.
I have used 1.54.07 and 1.54.27 on my AT&T Treo 750 with success.
The Treo uses Hermes ROM's ... here is the repository.
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Do not install 1.54.30.10 ... it's not a great radio from many accounts and once flashed, you will be stuck with it. You can't flash a new radio over the top of it.
ok now the radio is updated and it work i used the 1.54.07.00 so now am happy for that part but i got 1 more treo 750 i could not updated the radio due to there spl is 0.25 then 1.40 like my main one i normally test on them other treo so if they turn into a brick i would not care lol
is there a way to update a bootloader or i miss something somewhere?
Sounds like you need to Hard SPL the second phone.
well that what am trying to do when i do try with the hard spl v7 it does not work it goes blank so am trying to see if i can find a bootloader that 1.40 so i can so the same thing on the second phone to test radios and other kinky stuff
also on the side spot i notice that my phone fails to auto detect its band and the only way i can make it work is to select the right band for my provider is it coz i didn;t completely unlock my radio or i did something that bad? or re-flash the phone?
Anyone tried the 1.48 Radio ROM. Some are claiming better battery life than the 1.54.
xmadragex said:
well that what am trying to do when i do try with the hard spl v7 it does not work it goes blank so am trying to see if i can find a bootloader that 1.40 so i can so the same thing on the second phone to test radios and other kinky stuff
also on the side spot i notice that my phone fails to auto detect its band and the only way i can make it work is to select the right band for my provider is it coz i didn;t completely unlock my radio or i did something that bad? or re-flash the phone?
Click to expand...
Click to collapse
I wasn't aware there was a v7 to Hard SPL, I just used the version in the first post of the HardSPL sticky here in the Treo 750 forum. It's worked on both Treo's I have tried it on. I would say re-download and re-format the SD card and try again?
As for having to select bands on your phone, my guess is whatever ROM you have flashed might not have the carrier information for your provider included, or your radio might not support the proper bands. Telus doesn't use the same 3G bands as AT&T, but Rogers does. Depending on which version of the phone you have, that could be the issue.
rdecker692000 said:
Anyone tried the 1.48 Radio ROM. Some are claiming better battery life than the 1.54.
Click to expand...
Click to collapse
I tried it on AT&T and both the 1.54.07 and 1.54.27 ROMS were far better in terms of reception for me. Can't remember on the battery life since it's been awhile, but have to believe at the time if it was an issue I would have made the change back.
startngate said:
I tried it on AT&T and both the 1.54.07 and 1.54.27 ROMS were far better in terms of reception for me. Can't remember on the battery life since it's been awhile, but have to believe at the time if it was an issue I would have made the change back.
Click to expand...
Click to collapse
Okay - mine has 1.54.27 on it so I'll leave well enough alone. I just got this off of eBay (non camera version so I can take it to certain places at work) so I'm not sure what to expect for performance. The orginal battery lasted about 1/2 day so I just got a new OEM original battery and still burning it in.
Thanks for the tip.
rdecker692000 said:
Okay - mine has 1.54.27 on it so I'll leave well enough alone. I just got this off of eBay (non camera version so I can take it to certain places at work) so I'm not sure what to expect for performance. The orginal battery lasted about 1/2 day so I just got a new OEM original battery and still burning it in.
Thanks for the tip.
Click to expand...
Click to collapse
I've always been able to get through the day without issue, but can't say I'm a heavy user.
The stock battery is 1200mAh, but Innocell makes a 1600 mAh battery that fits in the OEM space if you need more juice.
http://www.seidioonline.com/product-p/basi16tr680s.htm
startngate said:
I wasn't aware there was a v7 to Hard SPL, I just used the version in the first post of the HardSPL sticky here in the Treo 750 forum. It's worked on both Treo's I have tried it on. I would say re-download and re-format the SD card and try again?
As for having to select bands on your phone, my guess is whatever ROM you have flashed might not have the carrier information for your provider included, or your radio might not support the proper bands. Telus doesn't use the same 3G bands as AT&T, but Rogers does. Depending on which version of the phone you have, that could be the issue.
I tried it on AT&T and both the 1.54.07 and 1.54.27 ROMS were far better in terms of reception for me. Can't remember on the battery life since it's been awhile, but have to believe at the time if it was an issue I would have made the change back.
Click to expand...
Click to collapse
well can ya link me the right hardspl
for my band selection problem is it the OS rom or the Radio rom and if there is one for my carrier where i can find it?
xmadragex said:
well can ya link me the right hardspl
Click to expand...
Click to collapse
It's the first 'sticky' thread in this forum as I previously mentioned.
http://forum.xda-developers.com/showthread.php?t=334100
xmadragex said:
for my band selection problem is it the OS rom or the Radio rom and if there is one for my carrier where i can find it?
Click to expand...
Click to collapse
It's likely not the OS ROM causing it. Assuming you have other phones that lock onto a signal properly in the same locations, then it's probably the radio ROM. However, if the Treo in question was not originally sold for your carrier (which I assume is Telus) then it's possible that the phone is trying to find a frequency for 3G that is not supported by Telus. For example, AT&T shares the same 3G frequencies with Rogers, which are different from Telus'. If you have a Rogers or AT&T version of the Treo, you would probably be better off just locking the phone down to GSM only.
As for finding the proper radio, you would need to try to find any Telus radio ROM that you can. Have no idea what that would be, or where to find it. If you have the original WM5 or WM6 official Telus installer package it would likely be included there. Otherwise you are just going to have to scour the net in seach of it.
Hmm, in my tests it is the OS that handles the Band selection only, what bands the Treo supports is up to the Radio firmware. You can flash a radio that, say, doesn't support UMTS 850, and yet it's possible to write a code to have it selectable.
And a word of advice. If you flash any of those Hermes ROM's, there's no taking it out. No overwriting. So, say if your wireless carrier upgrades their network like mine did, there's no going back to any of the suitable Radios that you can find.
And, just to be helpful, I'll write down which Official Treo Radio can be found in where(the ones I have):
CNG 1.16 (Cingular WM5) with Radio 1.12c [no HSDPA enabled by default]
VFU/VFE 2.18 (Vodafone UK and EU WM6) 2.18 with radio 1.47.02.00 [fast HSPDA on UMTS 2100 band]
H3E 2.19 (H3E Australia WM6) with radio 1.52.30.00 [no GSM locking, AUS band]
ROW 2.23 (WWE Generic WM6) with radio 1.54.00.00 [equal performance on all bands]
ATT/CNG 2.25 (AT&T WM6) with radio 1.54.27.00[Optimized for 1900/850 UMTS bands]
TEL 2.26 (Telstra WM6) with radio 1.54.31.00 [Extra band locking to single UMTS band (850)]
ROG/ROW 2.27 (Rogers and WWE WM6) with radio 1.54.01.00 [Slight performance increase over ROW 2.23]
VFE 2.30 (Vodafone New Zealand WM6) with radio 1.54.02.00 [bug fixes and improvements over ROG/ROW 2.27]
All personally flashed and extensively tested by me on two wireless carriers testing all bands.
mangatron said:
Hmm, in my tests it is the OS that handles the Band selection only, what bands the Treo supports is up to the Radio firmware. You can flash a radio that, say, doesn't support UMTS 850, and yet it's possible to write a code to have it selectable.
And a word of advice. If you flash any of those Hermes ROM's, there's no taking it out. No overwriting. So, say if your wireless carrier upgrades their network like mine did, there's no going back to any of the suitable Radios that you can find.
And, just to be helpful, I'll write down which Official Treo Radio can be found in where(the ones I have):
CNG 1.16 (Cingular WM5) with Radio 1.12c [no HSDPA enabled by default]
VFU/VFE 2.18 (Vodafone UK and EU WM6) 2.18 with radio 1.47.02.00 [fast HSPDA on UMTS 2100 band]
H3E 2.19 (H3E Australia WM6) with radio 1.52.30.00 [no GSM locking, AUS band]
ROW 2.23 (WWE Generic WM6) with radio 1.54.00.00 [equal performance on all bands]
ATT/CNG 2.25 (AT&T WM6) with radio 1.54.27.00[Optimized for 1900/850 UMTS bands]
TEL 2.26 (Telstra WM6) with radio 1.54.31.00 [Extra band locking to single UMTS band (850)]
ROG/ROW 2.27 (Rogers and WWE WM6) with radio 1.54.01.00 [Slight performance increase over ROW 2.23]
VFE 2.30 (Vodafone New Zealand WM6) with radio 1.54.02.00 [bug fixes and improvements over ROG/ROW 2.27]
All personally flashed and extensively tested by me on two wireless carriers testing all bands.
Click to expand...
Click to collapse
I guess we have different experiences then. I have had improvements in my phone locking onto a signal by changing radio ROMs without changing the OS ROM. I also have also used several of the Hermes radio ROM's and have been able to flash new radios without issue. The only exception I have ever seen is the 1.54.30.10 ROM which was widely reported to be impossible to flash over once installed (which for that reason I never tried).
I took from the OP that he was having trouble with his phone locking onto a signal and it was showing up as roaming a lot. I guess my thought was that perhaps he had a phone that wasn't originally sold for his network and it was trying to lock onto a band his carrier didn't support. Logically it seems like that might cause his problem, but I'm not well versed enough to know for sure.
As I mentioned, I am on AT&T and am using the 1.54.27 radio you report. It's the best of the radio ROMs I have tried. The Hermes 1.54.07 was the second best I tried. Thanks for the list, I'm sure it will help a lot of people. Of course you will now start getting requests to post them ...
Heh, when I said it's the OS that controls th selection, I mean just that, basically the drop-down menu in Band Selection. I too know that one can flash new radio's without changing OS's (you don't even have to Clear Data to use the new radio, just edit your choice of Data Connection setting, save, and your phone will automatically re-list your internet setup for use), and that's the thing. The OS will retain the Drop-down menu selection of bands, as it is tied to the OS (or both .pxp packages), an example is several tests I tried, for example the H3E ROM, does not have a selection for "GSM only" in the network type list. Say, if you flashed the ATT radio only then it will still retain the lack of GSM, because it is tied to the OS.
And yeah, I'm sure there would be at least one request. The problem is, I lost my source of instructions for ripping the Radio Firmware from the .nbh files and I do not want people having bricked Treo's all because I didn't follow instructions [I don't have]. Other course of action is to share th ROM itself, but that's large and I don't have an always on connection (this here Treo is my only source for internet, tether and built-in browser)
By the way, there are a lot of others who could not flash over other Hermes Radios, not that .10 one. I myself have 2 AT&T Treo's, and I flashed radio 1.50.00.00 and it remained no matter what I used to flash over it. I eventually gave away that half past dead Treo :/
well it used to be on auto with my telus card and it works on 3g network, the problem happend when i updated my treo 750 to 2.27 from 2.25 with wm6.1 am starting to think i mightn eed to reflash the rom it self
ok my wife as a fido sim card indeed i think its telus sim card the problem i have to use selective band it didn't needed that before i turn the phone from 2.25 ATT to 2.27 rwe the fido card work with the last radio version and i finally updated the bootloader
telus work with selective band >.>
now to know why fido card work auto but not telus
what does the radio do?
i got radio 1.54 .and i got two battery indicator when i installed HTC home (six tabs)
one bat is full and the other is like by bar. i want to remove the two battery because i got some newer/cooler battery indicator.
and i search some radios (idk why) so i try to installed other radios. and my phone stucks at the three colors.
and something pops up to my mind. i use cheetah unlocker. it got
FLASH SPL
RADIO.
idk the one.
so i flash spl and till i get to radio. it automatically updates to 1.1six some other icons on task bar changes.
but what does the radio do? and i dont know.
-sorry for the Six. because my Sixth button on keyboard is broken.
Hi, I recently bought a used i9103 on eBay that was imported from an overseas country (Still not sure which country), seeing as it was never sold in the US. After using it a few weeks, I notice that the signal jumps radically, even when the phone is stationary.
So my question is, which baseband/modem/radio would be best? (Specifically for T-Mobile USA)
As a note, I am in a major metro zone and other phones in this same area get a strong and consistent signal.
The baseband is currently XXLQ3.
Thanks.
You can try DDLP3 baseband from Indian ICS XWLP8 rom. That's the latest and that's why it should be the best one.
I flashed the modem alone from XWLP8. I'll report back in a few days if there's any difference. I guess I should also ask if there's any difference in hardware in the models shipped to different regions? Or is there only one model, just with different software?
There is only one model as far as we know, at least there weren't any others reported.
Just an update, flashing the Indian radio didn't seem to help at all. Signal still jumps up and down wildly. Turning on Data Roaming did not help either.
Well, the title says it all.
I'm on a canadian G935W8 version with Rogers and I was looking to flash some different modems as my call quality isn't the greatest.
I have looked all over and can find some Euro modems, but does anyone have any Idea which modems are both Exynos and LTE compatible that I can flash?
I'm rooted with TWRP installed on stock rom build APG1 (because rogers is terrible and never updates their stuff)
Thanks.
JG
I believe modem itself has got nothing to do with call quality? Unless if there is a glitch that I am un-aware of. What you could try is download an app called "Phone INFO Samsung" as your phone is rooted and navigate to SERVICE MODE -UE Settings - Setting -Protocol - AS- Release ver - AMR Ctrl -WB AMR Settings - and tap 4.(WB-WB)
Not sure about your provider, but I do believe they are offering VoLTE service to customers, are you not able to use it? Just for your info, I am using SM-G930F(Exynos,Australia,BPHJ build) and don't have any concern on call quality, even I am on 2G Network.
Tbh, I am not really sure if cross-flashing modem would even work or not, even if it works, I do remember that North America uses unique frequency band, and I doubt new modem would be compatible with that(No research have done, so I might be totally being stupid here) .
And finally, as your model is G93"5"W8 you should've posted this question on S7e forum.
Hope these information helps.
I have the Xoom MZ605. So it's an Everest. Right? However...
I've seen descriptions such as:
MZ601 = Xoom 3G + Wifi Europe model and it's called "Everest"
MZ600 = Xoom 3G + Wifi Verizon US model called "Stingray"
etc.
And I've seen people say that Wingray and Stingray will work on the MZ605, except I will have no 3G.
Well, question #1:
My unit does have a SIM card slot. I was even required to insert one before I could use the unit for the first time. After that, it was not required anymore. But the official firmware (upgraded OTA once to 4.0.4 by Motorola) never had any phone application, neither can I use the SIM card to have wireless internet. So I've been using WiFi only for years. Can I have mobile phone and internet connectivity with a CM firmware? Does this unit even have a GSM radio?
question #2:
There are too many CM firmwares and I am confused. Which ones would suit me? I've read somewhere that 4.4.4 is too slow and unstable, same as CM 11, and that CM 10 is recommended instead. But that page is 2 years old and things may have changed. Which ones do not cause any problem? I really need all the hardware features except HDMI.
TIA
No one is here now. I've been looking for a light weight firmware to use but these tablets are to old now