I got the two cases.
http://www.seidioonline.com/index.as...PROD&ProdID=75
http://www.seidioonline.com/index.as...PROD&ProdID=79
You and see from pic Sany0162 that the one case is NOT going to work the bottom is WAY to curved for the Flame. Which leaves the other case. In Sany0161, 0164 those two points were straight and were about 2 mm to narrow to fit the flame, but using a heat-gun (or a hair-dryer) I was able to move the plastic out about 1mm on each side. This allowed the case to fit nicely. The clip on the top is a bit tight, it holds the case in REALLY well but I felt it was a little TOO tight and might scratch the top so I heated it and bent it up 1mm in pic Sany0165 you can see it, this causes it to go in real nice but its now has a little play, (not enough to be a security problem its still really in there, but you might want to consider not doing this step..)
Finally you can see in Image1 that the headphone jack is covered, but with a little dremel action that was also fixed (see 0169 and 170).
And thats it... until they make a case this one isn't too bad.
PS: only allowed 5 files so the rest are in the zip
Is there a pouch rather than case? I just want to put the Flame in and take it out to use when it rings. I actually want to use it like how a phone is meant to be used. I don't want to put a case to my face.
You could use the case from an O2 XDA2s... that is what I was using prior, I'm sure you can order it as an accessory...
http://www.seeo2.com/product/XdaIIs/template/XdaIIsAccessories.vm
As for the case above, you don't hold that to your face? You slip it in and out of the clip, its a holster style case. Its really only advantage is easier 1-handed removal/insertion, and a smaller profile, (its mostly just the width of the original phone were the pouch is more cause of the flip... but if you want a pouch the XDA2s works quiet well.
Thanks....
Is the belt clip removable?
Not on that one. But there are usually lots of generic pouches, I'm sure you would find a bunch at a large cellular store that would fit the bill.
I'm using an aluminium case that allows to answer calls without opening it, so the screen doesn't get dirty. It adds some size, but if you use the clip belt, that's not a problem. Anyway I only use the Flame for work, so it goes into my case with everything else; for my spare time I use an HTC Touch that fits on any pocket and doesn't bother.
I am a week from having the cash to pick up an N1. I know there have been a lot of threads about cases, but I wanted to outline some of my thoughts and get opinions before I make my purchase. In addition, it is a little scary to hear reports of the phone getting broken easily: truth or not.
My problem is that I am a pocket phone holder. I do not wear belts often and when I do I am loaded with badges and other junk. Although I could hostler it, I already feel like batman without the fancy costume, and when I am not at work the hostler would not be an option.
So my plan is:
1. Get one of the plastic skins. My first choice is Clear Coat (new user so I cannot provide link). Most of these products appear to be the same, and although Clear Coat skins appear to have gaps and not fit as well as other brands, they have an installation guarantee. This is mainly to help the screen, but I will get full body to avoid scratches elsewhere.
2. Get a thin Silicon Gel Case. My theory is the gel will assist with gripping the device and absorb the shock from falls should they happen. This should also assist the clear coat skin against scratches to the body.
3. Get some sort of hard case to slip it into when I put it in my pocket. Since I normally carry my phone there, I am worried about the mysterious screen crackings which could be related to stress applied to the device when you sit and such. Hopefully a hard case will protect against this.
So, this is probably a little overkill, but am I completely insane?
My current phone is the T-mobile Shadow, which is a very cheap HTC phone with a plastic screen. I have had it for almost 2 years and have kept it in pretty good condition. I have 1 ding from accidentally placing it in the same pocket as my keys, and some major scratches when I had the genus idea of putting it in a ziplock bag when I went to Seaworld (well it did stay dry).
This is the most expensive phone I will have ever owned with only an very old world PDA being the most expensive mobile device. My wife is not exactly happy with me for spending this kind of money, and just seeing phones for calling people. As such, I am trying to make sure she cannot point a finger at a precaution I did not take: in addition to my own paranoia from reading the "I am having problems" forum on Google's site.
So, from the view point of people who have had other devices like this, am I being too worried or do these sound like reasonable precautions for this kind of device?
The information on these forums have been wonderful. Thanks for all the help!
I'm not sure what skin the last poster has used that yellowed, but I've used InvisibleSHIELD and Clear Protector, and they were still crystal clear after almost a year.
fujitsupalm said:
just gonna add one more here which is my favourite off all time, leather cases..
Click to expand...
Click to collapse
I have looked at these, but did not see this one. How stiff is the case? The leather looks pliable, and I want to prevent any bending of the phone.
I was looking at the flip open ones, but those seem too bulky. Also many of the pictures of these seem to have the phone photoshopped in, which makes me nervious. Hate the white thread too, but I could deal with that.
As for the invisible shield skins, did you have them actually tint the phone, or just - when applied - appear to be yellow? I have seen many reviews of these even over months of time and never heard this mentioned. Although I would be nervous about it permanently tinting the phone, if it just appears yellow when on then its worth a try since they can be removed. I know they are a pain to install, but I hate static protectors and really want something on the screen.
Thanks, fujitsupalm.
I saw your post in another thread. I think I might be leaning toward the flip on you posted pics of. How bulky is that? Does it interfer with the use of the screen?
I will probably get the flip or book version (wish it would let me post links), and get an invisible shield for the screen. It is humid here too, so I might have the same issue. However, if I can just remove it then its worth a shot.
Ultimately I settled on the trident case, pictures in this post. Thanks to gtny930 for finding it for us.
There are some other good case recommendations scattered through the thread, as I get the time I will source them up here for easier reference.
--------
Hey all, i've been searching amazon off and on for cases for our wonderful device, and finally pulled the trigger on one:
Link here
Says it's by HTC, and I ordered from BlueMall, at $0.32 I couldn't not get it...
Rubberized case, two pieces to fit the slide function, looks like a winner.
I doubt it'll be as good as an otterbox as far as protection, but a buddy of mine has an otterbox for his Inspire 4G - and suffers from serious overheating problems. Since our phone already suffers from that with the stock battery i'm gonna pass otterbox by on this phone. (Anker 1900 battery solved overheating problems for me)
Anyways, at less then $3.50 shipped, seemed like a fantastic deal.
Meantime, I have a screen protector and bodyglove on it now, which seems to be a good temporary fix until some proper protection was available. Love the glove, but to me it's only a temporary solution.
What're the rest of you doing for a case or protection for your phone? I'd love to hear about it.
ArmorSuit and HTC Messenger
I got this:
http://www.amazon.com/ArmorSuit-MilitaryShield-Protector-T-Mobile-REPLACEMENTS/dp/B0058XMYDU/ref=sr_1_3?s=wireless&ie=UTF8&qid=1314661800&sr=1-3
I posted "customer pics" of what is looks like on my phone too at Amazon.
I'm coming from the G1 and was used to the G1 sleeve so I also bought this:
http://www.amazon.com/HTC-Messenger-Pouch-HD2/dp/B003DZ13OG/ref=sr_1_1?s=wireless&ie=UTF8&qid=1314661896&sr=1-1
It's a nice fit and doesn't stick out the top.
As a side note.. I also bought the case you posted. I like it but it won't fit over the ArmorSuit and I really like how the suit looks and feels on the MT4GS. The phone with suit fits well in the pouch...good combo in my opinion.
Found this on Ebay. Still waiting for it (and MT4GS) to come. =[
I'm not allowed to post links yet so just put a dot in between.
http://www ebay.com/itm/HTC-MYTOUCH-4G-SLIDE-Hard-Cover-Case-SUMMER-FLOWER-/220839183408?pt=PDA_Accessories&hash=item336b0a8430#ht_2773wt_673
Lily.
MT4GS Cases / Shells
The rubberized hard Body Glove shells offered by T-Mobile (and sold on Amazon, eBay, etc...) are bulky and are missing holes for the microphone above the camera lens. I ended up buying the full body Invisible Shield and it looks great. The only problem is that they didn't include a piece for the bottom front of the phone (under the buttons and around the touchpad). I can put a hard case over the shield if I want, for extra protection or to just change up the look.
I have the solid black case. Just some things to note. First, the back piece is very tight, and I don't think it will ever fall off. However, when removing and replacing the cover, the clips can easily scratch your phone. Second, one or two clips may not actually "clip" to the phone, but rather just get stuck near the top so it still holds from pressure. This really isn't noticeable, but it leaves indents from the pressure on the phone's case. In addition, the clips scrape up against the backside of the screen when sliding up the phone, and over time, start leaving a very noticeable mark. I corrected this with a just a strip of tape over where it was scraping.
The protector for the sliding part of the phone was a bit of an issue. It clips very tightly to the phone, but the clips scrape a lot against the edges of the phone next to the keyboard. In addition to making it a little more difficult to slide the phone, it leads to wear overtime (noticeable wear actually started in less than a few hours of normal use for me). I corrected this by actually cutting off the clips, and using double sided adhesive to stick that part of the case on. It doesn't scrape anymore, but at the same time, it just doesn't look good as the case doesn't properly hold together.
I don't really see how much of this can be fully fixed. I used to own a G1, and I didn't notice the issue of cases scratching the phone until it was too late, but I was able to notice it on my MyTouch. I'm hesitant to go for the BodyGuardz. I had one on my G1, and though it was nearly invisible protection, and protected 95% of the phone, I ended up dropping my phone and it landed on a sharp rock on part of the 5% that happened to not be covered (which ironically actually are the corners of the phone, where it is very likely to land on).
I'm actually a fan of the body glove case. I'm just waiting for something with more clearance because of the anker battery. I've heard goods things about the otterbox, but it is kinda bulky.
Sent from my MyTouch 4G Slide
SolemnWishing said:
I have the solid black case. Just some things to note. First, the back piece is very tight, and I don't think it will ever fall off. However, when removing and replacing the cover, the clips can easily scratch your phone. Second, one or two clips may not actually "clip" to the phone, but rather just get stuck near the top so it still holds from pressure. This really isn't noticeable, but it leaves indents from the pressure on the phone's case. In addition, the clips scrape up against the backside of the screen when sliding up the phone, and over time, start leaving a very noticeable mark. I corrected this with a just a strip of tape over where it was scraping.
The protector for the sliding part of the phone was a bit of an issue. It clips very tightly to the phone, but the clips scrape a lot against the edges of the phone next to the keyboard. In addition to making it a little more difficult to slide the phone, it leads to wear overtime (noticeable wear actually started in less than a few hours of normal use for me). I corrected this by actually cutting off the clips, and using double sided adhesive to stick that part of the case on. It doesn't scrape anymore, but at the same time, it just doesn't look good as the case doesn't properly hold together.
I don't really see how much of this can be fully fixed. I used to own a G1, and I didn't notice the issue of cases scratching the phone until it was too late, but I was able to notice it on my MyTouch. I'm hesitant to go for the BodyGuardz. I had one on my G1, and though it was nearly invisible protection, and protected 95% of the phone, I ended up dropping my phone and it landed on a sharp rock on part of the 5% that happened to not be covered (which ironically actually are the corners of the phone, where it is very likely to land on).
Click to expand...
Click to collapse
I was going to edit in my response about the case I got in the first post - but after this one I quoted I need say not much more.
I really want to like the case, it feels nice and looks good on the phone...but it makes it too much of a pain in the ... to get the back of the case off.
I didn't realize how often I pop the back of the phone open to swap out memory cards until I put the case on.
It lasted on my phone for about 3 hours before I took it off...and it scratched one corner of my phone when I did it. Scratch isn't bad, and it'll probably buff out over time, but it's the first damage the phone has suffered - ironically from the thing that was supposed to prevent this.
If you are never going to pop open the back of the phone to get to the memory card, and you don't mind the backside of your screen-half of the phone getting scratched up when you slide it open - then this is a pretty decent case.
I think the scratching the back of the screen part can be solved by using a knife to cut a sliver off the part that sticks op, then maybe using a small piece of electrical tape to cover that clip.
I like it, I want to like it, but I can't use it - I take the phone apart too damn much for a case like this to be practical.
I'm on the lookout for a gel-type case now. Think that'll be the perfect solution. If anyone finds one, please mention it here.
I got the black cheap case today. After reading the reviews I knew better than to just throw it on there. So I took a small metal file that I have, and proceeded to shave each clip down just a little. After a few trials I got the clips shaved down enough that they all fit and are not pressing against the bottom of the screen hard enough to scratch it.
The coating on this case was not really rubber. Its more of a dusted flat black. It's not slick to the touch, but it doesnt grip like the rubber of the phone.
The phone still fits into the generic style T-mobile mount. But its not as secure as without. I can turn it upside down and give it a light shake without coming loose. So hopefully it will be fine.
I got my psychedelic cover and I'm not very impressed with it. It makes the phone very bulky and awkward to hold (maybe because of my small girly hands -_-).
I find taking the back cover off particularly stressful because I'm scared I'd rip the screen off the keyboard.
Protection wise I haven't dropped my phone yet to see what kind it would provide but I'm guessing it wouldn't fall off the phone if dropped.
Haven't seen any dents or scratches caused by it.
I think I'd prefer it if it had a more rubbery feel as the texture is kind of smooth and slippery.
Overall, I'm satisfied with it but I wish I could figure out a way to take off the cover without the fear of destroying it. Haha.
Lily.
@siani_8
I got this: ....
.....
As a side note.. I also bought the case you posted. I like it but it won't fit over the ArmorSuit and I really like how the suit looks and feels on the MT4GS. The phone with suit fits well in the pouch...good combo in my opinion.
Quick question - in the pictures you uploaded to Amazon the phone back and sides seem to have a checker pattern. Is that pattern due to the protector?
The otterbox exists for this phone? Or you speaking generally about the otterbox product line?
Sent from my MyTouch 4G Slide using xda premium
ssb33 said:
@siani_8
I got this: ....
.....
As a side note.. I also bought the case you posted. I like it but it won't fit over the ArmorSuit and I really like how the suit looks and feels on the MT4GS. The phone with suit fits well in the pouch...good combo in my opinion.
Quick question - in the pictures you uploaded to Amazon the phone back and sides seem to have a checker pattern. Is that pattern due to the protector?
Click to expand...
Click to collapse
Yes, it's a woven "carbon fiber" pattern. I took the pictures at angles where the light shows it more clearly. I think it looks nice and provides a "non-slip" surface as well without adding any bulk to the phone when you want to use it, which I personally prefer.
siani_8 said:
I got this:
http://www.amazon.com/ArmorSuit-MilitaryShield-Protector-T-Mobile-REPLACEMENTS/dp/B0058XMYDU/ref=sr_1_3?s=wireless&ie=UTF8&qid=1314661800&sr=1-3
I posted "customer pics" of what is looks like on my phone too at Amazon.
I'm coming from the G1 and was used to the G1 sleeve so I also bought this:
http://www.amazon.com/HTC-Messenger-Pouch-HD2/dp/B003DZ13OG/ref=sr_1_1?s=wireless&ie=UTF8&qid=1314661896&sr=1-1
It's a nice fit and doesn't stick out the top.
As a side note.. I also bought the case you posted. I like it but it won't fit over the ArmorSuit and I really like how the suit looks and feels on the MT4GS. The phone with suit fits well in the pouch...good combo in my opinion.
Click to expand...
Click to collapse
Thanks for linking this and posting the pics on Amazon., I'm going to order one today.
Thanks. I ordered one and installed it yesterday. The front and back went on great. I had more trouble with the sides but that is because I am not the most deft person around. There are a lot long thin pieces but MT4GS has a lot of moving parts. The phone looks great from the front. But the back has a bubble or two - again my clumsiness.
I wonder how long Otterbox will ignore this phone? Annoying....
Meanwhile, this HTC shell is gettin it done. Only complaint is that its not Otterbox.
http://www.amazon.com/gp/product/B005H98VI2
_atlien_ said:
I wonder how long Otterbox will ignore this phone? Annoying....
Meanwhile, this HTC shell is gettin it done. Only complaint is that its not Otterbox.
http://www.amazon.com/gp/product/B005H98VI2
Click to expand...
Click to collapse
That's about the same thing I got that I posted about before - just mine is in black.
I know I said a few posts back that I wasn't going to use it, but I had to do something to try to keep it safe.
I've been using it for a few days now, and while I have my gripes, I suppose it's okay.
I got tired of not being able to put it down anywhere, for fear of scratching the camera lens. This case sits further down then the lens, so it isn't the thing the weight of the phone rests on.
Before, i'd have to find something soft to put it down on everywhere I went, which was annoying. I wouldn't put it in my pocket, because they are always full of dust and whatnot - that little grainy stuff gets into the phone and I didn't want that.
Now, with the case on, it doesn't fit in my belt holster anymore - so I have to put it in my pocket or carry it. Desperately seeking another solution but coming up short.
What i'm thinking about doing is drilling some holes in the back of the case, and attaching a belt clip to the hard case shell itself.
So now i'm looking for either a belt holster or a clip I can attach to the hard case itself. Whatever ends up happening, i'll get some pictures and put 'em up here.
What I really, really, really, really want is a soft-rubber case, like a gel case of some sort that can absorb shock - not some hard plastic thing.
_atlien_ said:
I wonder how long Otterbox will ignore this phone? Annoying....
Meanwhile, this HTC shell is gettin it done. Only complaint is that its not Otterbox.
Click to expand...
Click to collapse
Can you 2 that got this case tell me if it fits OK? I hate cases that feel like they are going to fall off after they are on...does this one do that? Specifically when you slide the keyboard up with your thumbs does the front part of the case feel like it would fall off because of your thumb pressure?
Just wanted to be sure it was somewhat well constructed...the $5 price tag just has me concerned.
cOvertKEEN said:
Can you 2 that got this case tell me if it fits OK? I hate cases that feel like they are going to fall off after they are on...does this one do that? Specifically when you slide the keyboard up with your thumbs does the front part of the case feel like it would fall off because of your thumb pressure?
Just wanted to be sure it was somewhat well constructed...the $5 price tag just has me concerned.
Click to expand...
Click to collapse
No, it's fine. I've dropped the phone twice and the case hasn't come off. And it certainly isn't about to come off from handling/usage of the phone. It fits snug. Supposedly its made by HTC, if that means anything. The case does it's job without problems.
Just waitin for Otter.....
Any body have a silicone case? Or one of these?
http://www.ebay.com/itm/HTC-MYTOUCH...Accessories&hash=item231421d01f#ht_1896wt_922
Looks good. Other colors available too.
cOvertKEEN said:
Can you 2 that got this case tell me if it fits OK? I hate cases that feel like they are going to fall off after they are on...does this one do that? Specifically when you slide the keyboard up with your thumbs does the front part of the case feel like it would fall off because of your thumb pressure?
Just wanted to be sure it was somewhat well constructed...the $5 price tag just has me concerned.
Click to expand...
Click to collapse
_atlien_ said:
No, it's fine. I've dropped the phone twice and the case hasn't come off. And it certainly isn't about to come off from handling/usage of the phone. It fits snug. Supposedly its made by HTC, if that means anything. The case does it's job without problems.
Just waitin for Otter.....
Click to expand...
Click to collapse
It fits snug, coming off accidentally isn't a problem. Both the top piece and the bottom piece are secure, normal - or even some exaggerated abnormal - use won't knock it off.
The longer I use the case the more it grows on me, I really like the silky feel of it. There have been a few situations already where having a case protected the phone - I haven't dropped it and hope I never do, but since it's becoming a portable video game system/controller amongst other things it can't be without one.
I suppose you could do far worse then this case, but i'd trade it for a gel-type rubber case in a heartbeat. Hard cases don't protect from shock damage.
Dear XDA,*
For the past three years, I've been personally opposed to cases for cell phones. It just seems like too much bulk for comfort, especially with today's crop of slim and sleek phones. In that time frame I've carried an iPhone 3GS, Garminfone, MT3GS, and since May a MT4GS.
But now I'm on my third digitizer for the MT4GS and I'm really starting to think that I might need some sort of protection for the phone. I picked up a hard cover from Amazon, but I don't like the extra bulk in my pocket, I worry about the potential for damage to the slide mechanism and unless I'm constantly removing the phone from the case my HTC Car Dock is useless. I also picked up a SkinGuardz skin from Amazon, but it doesn't protect the sides of the phone. Now I'm considering a Skinomi skin.
What should I do, man up and live with the case, go for the second skin or just stop dropping the stupid phone?
Signed,
Butter Fingers
*A Dear Abby homage
Safest thing is that case tbh. But on my old slider phone (and 2 others phones) the case caused to much of a gap between the KB slider and the lcd display which in turn stressed our flex cables and made them go bad. So now one of 3 phones only works with the KB lid closed. I know flex cables go out on sliders but 3 sliders with the same case suffering the same exact symptoms isn't coincidence to me.
Whatever it may be I might be picking up a case IF my doubleshot wasn't stolen out my mailbox. Which I feel it was, and if that happened I won't needs a case at all. And ill have to leave you guys very soon. But that's another day another post let's hope.
Sent from my myTouch_4G_Slide using Tapatalk 2
I found the mt4gs cases to be lacking as well.
Here is my solution:
TPU case for Samsung Galaxy Axiom (can't post ebay link just search)
then modify the holes with my dremel to match mt4gs.
All I wanted was a TPU case that would fit the phone. I didn't need the keyboard, I just wanted protection to stop the battery and case from popping out everytime the phone hit the ground.
My Graphite 128 is on the Fed-Ex truck due to arrive tomorrow.
My Black Folio case is sitting at home waiting for the phone.
Another user posted that the case is very difficult to remove and damaged his phone in the process:
http://forum.xda-developers.com/showpost.php?p=63705459&postcount=133
ChrisJ said:
I had been using the Adopted case since getting my second Graphite (first had cosmetic damage out of the box). It is really easy to get on and off and I've had no issues with it.
My Leather Folio case was delivered this morning (bought for those occasions I want an extra bit of protection) and so I quickly the 6P out of the Adopted and into the Folio. Nice snug fit, nice case. Magnet for screen activation etc.
However, here's where the problems start. Can I hell get the phone out of the Folio case, it is well and truly stuck. At best I can get one corner off (with some force) but that just makes the other three corners even tighter. There is no way I could get this off without damaging the phone. Cutting it off would be a very risky procedure.
Click to expand...
Click to collapse
So can anyone else comment on this?
Maybe I should send the Folio Back.
I got the folio a few weeks ago and I loved it. The quality was top notch, the phone felt solid with the case on. Unfortunately it's true that it's nearly impossible to remove the case. I got caught in a panic, thinking I would damage my brand new phone. I ended up having to bend and almost break the folio case, hurting my fingers, to finally get it off. HUGE design flaw, stay away.
I found a way to remove the case from the 6p with ease, but not before pulling my hair out for ages.
https://www.youtube.com/watch?v=u0oOsTlv5c4
(I cant get the youtube button on the forum to work, if a mod sees this and can help out that would be great.)