Hello! I need help. I bought a new phone in China : Model PW28 "Key Features:
HSDPA 7.2M bps(7227)
Android 2.2FroYo
GPS Supported
" system Android 2.2FroYo
Technical Standard
Size (mm):106.3*58*13.2mm
Platform:Qualcomm MSM7227-1
Memory: 4GB ROM+2GB RAM
Network:GSM Quad-band 850/900/1800/1900MHz, GPRS, EDGE
UMTS850/2100, 7.2M bps HSDPA
Chipset HSDPA 7.2Mbps
Display:3.2" HVGA TFT LCD
Camera: 5M CMOS, Auto focus
Bluetooth:Bluetooth 2.1 + EDR
JAVA:Midp 2.0 /3GP/MP4
GPS:Yes
External Memory:Micro SD memory card( up to 16GB)
FM Radio:Built-in
Wifi:Yes, 802.11b/g
Battery:100mAh
Frequency Band GSM/GPRS/EDGE 850/900/1800/1900 MHz
UMTS "2100MHz/850Mhz(Optional)
Now that Android icon freezes at startup. Show me how to fix it back to factory defaults or ROM upgrade. Thanks! Excuse my English!
Hello! I need help. I bought a new phone in China :
Model PW28 "Key Features:
HSDPA 7.2M bps(7227)
Android 2.2FroYo
GPS Supported
" system Android 2.2FroYo
Technical Standard
Size (mm):106.3*58*13.2mm
Platform:Qualcomm MSM7227-1
Memory: 4GB ROM+2GB RAM
Network:GSM Quad-band 850/900/1800/1900MHz, GPRS, EDGE
UMTS850/2100, 7.2M bps HSDPA
Chipset HSDPA 7.2Mbps
Display:3.2" HVGA TFT LCD
Camera: 5M CMOS, Auto focus
Bluetooth:Bluetooth 2.1 + EDR
JAVA:Midp 2.0 /3GP/MP4
GPS:Yes
External Memory:Micro SD memory card( up to 16GB)
FM Radio:Built-in
Wifi:Yes, 802.11b/g
Battery:100mAh
Frequency Band GSM/GPRS/EDGE 850/900/1800/1900 MHz
UMTS "2100MHz/850Mhz(Optional)
Now that Android icon freezes at startup. Show me how to fix it back to factory defaults or ROM upgrade. Thanks! Excuse my English!
Hello my sister sent me a phone from Korea its LTE and i was wondering if it will work on any of the cellular networks hear in canada and wuld its lte work on telus or rogers
hear are the specs
RAM:capacity: 1 GiB
ROM_capacity: 14.9 GiB
Display
Display:Type: Supported
Display-Diagonal: 4.8 "
Display:Resolution: 720 x 1280
Video+out: 1920x1080 (1080p) resolution
Sound
Microphone(s): mono
Loudspeaker(s): Supported
Audio+Output: 3.5mm
Cellular+Phone
Cellular+Networks: CDMA1800 (BC4)
Cellular-Data;Links: cdmaOne, CDMA2000 1xRTT, CDMA2000 1xEV-DO Rel. 0, CDMA2000 1xEV-DO Rev A, CDMA2000 1xEV-DO Rev B
Call:Alert: 64 -chord melody
Vibrating-Alert: Supported
Speakerphone:: Supported
Secondary-Cellular;Phone
Dual:Cellular;Network;Operation: Parallel operation
Secondary-Cellular_Networks: LTE850 (B5)
Secondary-Cellularata;Links: LTE
Control-Peripherals
Positioning_Device: Multi-touch screen
Primary;Keyboard: Not supported
Directional-Pad: Not supported
Scroll;Wheel: Not supported
Interfaces
Expansion:Slots: microSD, microSDHC, TransFlash
USB: USB 2.0 client, 480Mbit/s
micro-USB
Bluetooth: Bluetooth 4.0
Wireless+LAN: 802.11a, 802.11b, 802.11g, 802.11n
Infrared-Gate: Not supported
Multimedia+Telecommunication
Analog:Radio+Receiver: Not supported
Digital+Media+Broadcast+Tuner: T-DMB
Satellite+Navigation
Built-in_GPS;module: Supported
Complementary:GPS+Services: Assisted GPS, QuickGPS, Geotagging, Simultaneous GPS
I dont know but any probs on it and ur welcome here:laugh:
Hi!
Is the Q capable of doing wifi over 5GHz ?
Accoriding to:
http://www.qualcomm.com/snapdragon/smartphones/motorola-photon-q
and
http://en.wikipedia.org/wiki/Snapdragon_(system_on_chip)#Snapdragon_S4
it should be capable of doiung so.
Is there a way to determine the exact cpu type build in? ... did a cat /proc/cpuinfo
-> Hardware is : msm8960dt
So the hardware is capable of 5Ghz Wifi. Maybe there are some antennas missing.
As far as I can tell, it isn't. When I run the INSSIDer application, it does not detect any 5 ghz channels, despite having 5 ghz channels in range.
Sucks! I have to buy a dual band router because the 2.4GHz spectrum is crowded in this apartment. I literally get a better signal from my upstairs neighbors router than i do my own.
Sent from my XT897 using Tapatalk 2
jae18708 said:
Sucks! I have to buy a dual band router because the 2.4GHz spectrum is crowded in this apartment. I literally get a better signal from my upstairs neighbors router than i do my own.
Sent from my XT897 using Tapatalk 2
Click to expand...
Click to collapse
Try changing the channel on your router.
As a matter of fact, you can use that same inssider application I mentioned to find what channels nearby wifi networks are running, and change the channel yours is operating on to avoid the interference.
Have you tried poking around in the build.prop to see if 5 GHz can be enabled? You may have to find one from an Android device that does have 5 GHz to get the proper line.
Found this @ /system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini
Something about gEnableApProt states about n.
Hopefully someone is wiser and braver than me to know more about this file and changes which may enable 5ghz.
Code:
# This file allows user to override the factory
# defaults for the WLAN Driver
# Enable IMPS or not
gEnableImps=1
# Enable/Disable Idle Scan
gEnableIdleScan=0
# Increase sleep duration (seconds) during IMPS
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0
# Enable BMPS or not
gEnableBmps=1
gBmpsMinListenInterval=1
gBmpsModListenInterval=2
gBmpsMaxListenInterval=3
gPowerUsage=Max
#Telescopic Beacon skipping
gTelescopicBeaconWakeupEn=1
telescopicBeaconTransListenInterval=3
telescopicBeaconTransListenIntervalNumIdleBcns=1
telescopicBeaconMaxListenInterval=3
telescopicBeaconMaxListenIntervalNumIdleBcns=1
# Performance parameters
gEnableCloseLoop=1
gDataInactivityTimeout=120
gChannelBondingMode5GHz=1
# Enable suspend or not
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
gEnableSuspend=3
# Phy Mode (auto, b, g, n, etc)
gDot11Mode=0
# Handoff Enable(1) Disable(0)
gEnableHandoff=0
# CSR Roaming Enable(1) Disable(0)
gRoamingTime=0
# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
Intf3MacAddress=000AF58989FC
# UAPSD service interval for VO,VI, BE, BK traffic
UapsdMask=0
InfraUapsdVoSrvIntv=0
InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0
# Disable RSSI FW filtering
gEnableFWRssiMonitoring=0
# Make 1x1 the default antenna configuration
gNumRxAnt=1
# Beacon filtering frequency (unit in beacon intervals)
gNthBeaconFilter=50
# Enable WAPI or not
# WAPIIsEnabled=0
# Flags to filter Mcast abd Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=0
#Flag to enable HostARPOffload feature or not
hostArpOffload=1
#SoftAP Related Parameters
# AP MAc addr
gAPMacAddr=000AF58989EF
# 802.11n Protection flag
gEnableApProt=1
#Enable OBSS protection
gEnableApOBSSProt=0
#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1
# Fixed Rate
gFixedRate=0
# Maximum Tx power
# gTxPowerCap=30
# Fragmentation Threshold
# gFragmentationThreshold=2346
# RTS threshold
RTSThreshold=2347
# Intra-BSS forward
gDisableIntraBssFwd=0
# WMM Enable/Disable
WmmIsEnabled=0
# 802.11d support
g11dSupportEnabled=1
# SAP Country code
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
# Example
# US Indoor, USI
# Korea Outdoor, KRO
# Japan without optional byte, JP
# France without optional byte, FR
#gAPCntryCode=USI
#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff=0
# SAP auto channel selection configuration
# 0 = disable auto channel selection
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
gApAutoChannelSelection=0
# Listen Energy Detect Mode Configuration
# Valid values 0-128
# 128 means disable Energy Detect feature
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
# 10-128 are reserved.
# The EDET threshold mapping is as follows in 3dB step:
# 0 = -60 dBm
# 1 = -63 dBm
# 2 = -66 dBm
# ...
# 7 = -81 dBm
# 8 = -84 dBm
# 9 = -87 dBm
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
#
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
#
gEnablePhyAgcListenMode=128
#Preferred channel to start BT AMP AP mode (0 means, any channel)
BtAmpPreferredChannel=0
#Preferred band (both or 2.4 only or 5 only)
BandCapability=1
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
enableBeaconEarlyTermination=1
beaconEarlyTerminationWakeInterval=3
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
gEnableBtAmp=0
#SOFTAP Channel Range selection
gAPChannelSelectStartChannel=1
gAPChannelSelectEndChannel=11
#SOFTAP Channel Range selection Operating band
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
gAPChannelSelectOperatingBand=0
#Enable Keep alive with non-zero period value
gStaKeepAlivePeriod=55
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
gEnableBypass11d=1
#If set to 0, will not scan DFS channels
gEnableDFSChnlScan=1
# Enable logp/SSR
gEnableLogp=1
# Enable Automatic Tx Power control
gEnableAutomaticTxPowerControl=1
# Priority Setting:COUNTRY IOCTL > 11d > NV default
gCountryCodePriority=1
END
# Note: Configuration parser would not read anything past the END marker
Sent from my awesome XT897
Found this :
http://www.modaco.com/topic/361678-5ghz-wifi/
Try it when i am home and in range of a 5ghz rooter.
Sent from my awesome XT897
A quick look through iwlist looks good so far
Code:
sh-4.2$ iwlist wlan0 frequency
wlan0 32 channels in total; available frequencies :
Channel 01 : 2.412 GHz
Channel 02 : 2.417 GHz
Channel 03 : 2.422 GHz
Channel 04 : 2.427 GHz
Channel 05 : 2.432 GHz
Channel 06 : 2.437 GHz
Channel 07 : 2.442 GHz
Channel 08 : 2.447 GHz
Channel 09 : 2.452 GHz
Channel 10 : 2.457 GHz
Channel 11 : 2.462 GHz
Channel 12 : 2.467 GHz
Channel 13 : 2.472 GHz
Channel 36 : 5.18 GHz
Channel 40 : 5.2 GHz
Channel 44 : 5.22 GHz
Channel 48 : 5.24 GHz
Channel 52 : 5.26 GHz
Channel 56 : 5.28 GHz
Channel 60 : 5.3 GHz
Channel 64 : 5.32 GHz
Channel 100 : 5.5 GHz
Channel 104 : 5.52 GHz
Channel 108 : 5.54 GHz
Channel 112 : 5.56 GHz
Channel 116 : 5.58 GHz
Channel 120 : 5.6 GHz
Channel 124 : 5.62 GHz
Channel 128 : 5.64 GHz
Channel 132 : 5.66 GHz
Channel 136 : 5.68 GHz
Channel 140 : 5.7 GHz
Current Channel:6
Sent from my awesome XT897
So back home but unable to see 5ghz wifi ;( don't know if i miss something to edit, or if the gui is "forcing" 2.4 ghz.
Maybe a more experienced user can hop in.
Finally answering and closing this thread.
I am now on scrillax gsm cm10.1 nightlies and able to connect to 5ghz networks.
Somehow the signalstrength is not properly shown, so it may use a stronger 2.4 Ghz channel if applicable. Forcing 5Ghz works just fine.
Gesendet von meinem XT897 mit Tapatalk 2
I wonder what is different in skrillax's ROM that enables 5GHz, and if it's something that can be applied to stock JB.
BAMF said:
I wonder what is different in skrillax's ROM that enables 5GHz, and if it's something that can be applied to stock JB.
Click to expand...
Click to collapse
Is this thread really dead?
I can't imagine that nobody is interested in getting 5GHz WiFi working...
probably it's just some regulatory settings, as there seem to be ROMS that are capable of 5GHz wifi.
Just tried CM11 nightly and CarbonROM, no luck with both.
Can't somebody experienced have a look at the configuration?
Killler07 said:
Is this thread really dead?
I can't imagine that nobody is interested in getting 5GHz WiFi working...
probably it's just some regulatory settings, as there seem to be ROMS that are capable of 5GHz wifi.
Just tried CM11 nightly and CarbonROM, no luck with both.
Can't somebody experienced have a look at the configuration?
Click to expand...
Click to collapse
See this thread:
http://forum.xda-developers.com/showthread.php?t=2671559
Hello,
While going through the official Cynagnogen Mod "tutorial" to install CM on an unsupported device, I read that if you can find a phone that is similar to yours in specs and that is supported you can install CM for that device on your phone . My phone is a Cubot ZORRO 001 , and i would like to know if you know about any phone enough similar to mine.Small differences like screen size or storage aren't a problem. If I got anything wrong here please tell me.
Specs:
Microprocessor, Chipset
CPU Clock: 1200 MHz
CPU: Qualcomm Snapdragon 410 MSM8916
Browse devices based on this microprocessor
Memory, Storage capacity
RAM capacity: 1 GiB
ROM capacity: 7.5 GiB
Display
Display Technology: color IPS TFT , 16777216 scales
Display Diagonal: 5 "
Display Resolution: 720 x 1280
Sound
Microphone(s): mono
Loudspeaker(s): mono
Audio Output: 3.5mm
Cellular Phone
Cellular Networks: GSM850, GSM900, GSM1800, GSM1900, UMTS900 (B8), UMTS2100 (B1), LTE2100 (B1), LTE1800 (B3), LTE2600 (B7), LTE900 (B8), LTE800 (B20)
Cellular Data Links: GPRS, EDGE, UMTS, HSDPA, HSUPA, HSPA+, LTE
Call Alert: 64 -chord melody
Vibrating Alert: Supported
Speakerphone : Supported
Secondary Cellular Phone
Dual Cellular Network Operation: Dual standby
Secondary Cellular Networks: GSM850, GSM900, GSM1800, GSM1900
Secondary Cellular Data Links: GPRS, EDGE
Control Peripherals
Positioning Device: Multi-touch screen
Primary Keyboard: Supported
Directional Pad: Not supported
Scroll Wheel: Not supported
Interfaces
Expansion Slots: microSD, microSDHC, TransFlash
USB: USB 2.0 host/client, 480Mbit/s
micro-USB
Bluetooth: Bluetooth 4.0
Wireless LAN: 802.11b, 802.11g, 802.11n
Infrared Gate: Not supported
Multimedia Broadcast
Analog Radio Receiver: FM radio (88-108 MHz)
Digital Media Broadcast Tuner: Not supported
Satellite Navigation
Built-in GPS module: Supported
Complementary GPS Services: Assisted GPS, QuickGPS, Geotagging, Simultaneous GPS (S-GPS)
Built-in Digital Camera
Primary Camera: 13 MP
Autofocus (AF): Supported
Optical Zoom: 1 x
Macro Mode: Supported
Built-in Flash: mobile light (LED)
Secondary Camera: 5 MP
Additional Details
Built-in accelerometer: Supported
Battery: Supported
Battery Capacity: 2200 mAh
Ok I found smth, the YU Yunique . It has same CPU, RAM, storage , but some things are still different. Do you think there are enough similar things for my phone to support CM ?
Specs:
Codename: jalebi
Vendor: YU
Release Date: 2015 September
Type: phone
Platform: Qualcomm MSM8916 Snapdragon 410
CPU: 1.2 Ghz quad-core Cortex A53
GPU: Adreno 306
RAM: 1GB
Weight: 128 g (4.52 oz)
Dimensions: 134.5 x 67.5 x 8.3 mm (5.30 x 2.66 x 0.33 in)
Screen dimension: 119 mm (4.7 in)
Resolution: 720x1280
Screen Density: 312 ppi
Screen Technology: IPS LCD
Internal Storage: 8GB
SD Card: up to 32GB
Bluetooth: 4.0
Wi-Fi: 802.11 b/g/n
Main camera: 8MP
Secondary camera: 2MP
Power: 2000 mAh
Peripherals: 64 bit, dual SIM
CM Support: 12.1, 13