[Q][URGENT] Booting Loop problem, how can it be fixed? - General Questions and Answers

How can this be fixed? I can still do the Vol Down + Power combination thing, but the phone will not load to my home screen via normal start up.
I have no idea how to fix this, seeing as it was caused by me applying a theme in Metamorph. I don't have SDK either...
I have a HTC Magic, 32B.
I'm trying to fastboot recover it right now, but even when my phone says FASTBOOT USB, the command prompt still says <Waiting for device>
I really need help.

I really need help right now, it's my only phone, and I'm not in the position to buy a new one.

Related

[Q] My phone loads until it gets to the Cyanogen Logo, where it loops...

How can this be fixed? I can still do the Vol Down + Power combination thing, but the phone will not load to my home screen via normal start up.
I have no idea how to fix this, seeing as it was caused by me applying a theme in Metamorph. I don't have SDK either...
I have a HTC Magic, 32B.
I'm trying to fastboot recover it right now, but even when my phone says FASTBOOT USB, the command prompt still says <Waiting for device>

[DEV TIP]How I Got Out Of A Semi-Brick

I almost had a heart attack last night doing some kernel work. This is what happened, and how I got out of it.
I had just finished compiling a kernel I was working on and was excited to flash it and give it a run. So I built the boot.img and did
Code:
adb reboot bootloader
I got into the bootloader and
Code:
fastboot flash boot [B][I]boot.zip[/I][/B]
fastboot reboot
Working quickly, a got a little sloppy. Most unfortunately, I had a boot.zip in the same folder as the boot.img so boot.zip got flashed to the boot partition. Upon reboot, I got the usual splash screen but the upper left hand corner indicated I was in "RSD Mode 3". I pressed and held Vol up + power to get into bootloader but that was unresponsive. All I could do was press Vol Down + power which brought me back to the same state. I was unable to issue fastboot commands from here as well. This is what I did to fix it.
While I was in "RSD Mode 3" I did
Code:
fastboot flash boot boot.img
Even though there was no response from the device, I pressed Vol Down + power until the screen went black. I then quickly pressed and held Vol Up + power. The device then went into the bootloader, received the queued command from fastboot, and flashed the boot.img. Finally, I did
Code:
fastboot reboot
and was back in the game.
Guys, I think the moral of the story is to slow down and be careful with fastboot. You can bet i'll be a little more careful
good post I'm sure this will help devs in the future
way to stay calm under pressure lol. good info.
Small world, I used to live in Fontana for 25 years and moved to NY couple of years ago Oh and thanks for the tip
Ran into this today, i had a similar, but different experience..hope this helps
Once i got into the RSD 3 mode, fastboot commands were basically dead...all i would get was <waiting for device>...
in order to get out, i had to hold BOTH VOL+ and VOL- and Power at the same time, then as soon as the screen turned off, I had to press VOL- and power at the same time to get to a 'regular' looking boot screen. I saw regular because there was no text at the top ofthe screen; however fastboot commands would work here. Because i FUBAR'd a kernel install, i just did
fastboot flash boot boot.img
fastboot reboot
and voila...it was alive again
a bit scary though
Ok, so I definitely know the heart attack feeling, and hopefully someone here can help me out. I got my Xoom today(wifi), and went looking for a root. I found a link to a root here that -said- it worked for both 3g and wifi models(found out later that it doesn't, obviously). So, I flashed the boot image, and came up with the RSD message. At that point all fastboot and adb capability was lost, and I can't seem to get it back.
Here's what happens with the following button combo's:
Hold Power+VolUp and release on screen-black: Motorola splash screen(dual core etc) with no text in corner
Hold Power+VolUp until after the splash comes up: splash with "Starting RSD protocol support 3"
Hold Power+VolUp and then hold VolDown immediatedly afterward: Splash screen with "Starting Fastboot protocol support."
Hold Power+VolUp and then VolDown after waiting a second: Splash screen with NvFlash/RSD/Fastboot menu
Hold Power+VolUp and then press VolUp again: Splash with "Starting RSD protocol support 3"
If I choose Fastboot from the menu, it just sits at the "starting fastboot protocol support".
If I choose RSD, it gives me the "starting RSD protocol support 3"
If I choose NvFlash, it says "entering nvFlash (something) and the screen immediately goes black and the notification led comes on (sits there until reboot)
No other button combinations seem to do anything. Holding Power+VolDown doesn't do anything from any mode, and Power+VolUp+VolDown acts just like Power+VolUp.
In any mode, I can't issue fastboot or adb commands. Fastboot simply says <waiting for device> for anything. I tried the advice above, to queue up a "good" boot.img (from here at xda), but it doesn't recognize it on a reboot from/to any mode I can get to. I've tried each about 20-30 times now, and I'm about ready to test the thing's shatter-resistance with my fist, so any help here would be -greatly- appreciated.
Quick update to previous post: Resolved!!
My advice? If you get stuck unable to fastboot or adb in linux, try it in windows. I hadn't booted into win for over a year, so it never occured to me until I saw someone mention it in the Tiamat thread. Even a fresh JDK/SDK install in Ubuntu didn't work for me. I didn't have any tools or SDK's installed in my winXP partition, but after a quick install, it worked first time, so now I'm the happy owner of a rooted Wifi Xoom with SD card.
Once again, the XDA forum saves the day. I love this place.
I recommend everyone keep a backup copy of their system.img around just in case too. I was going nuts after messing with my framework-res.apk file to get SMS working (for the verizon web account activiation message). I used root explorer, and BAM! crash, crash, FC, FC, then stuck at the moto logo at boot. I couldnt get it back with just a boot.img flash. I went for broke and found a post of the HI66 system.img. it was HUGE, dont know if thats what I needed. but flashed that and I was back in business as nothing else was working and couldnt get ADB to take to push the old framework-res.apk.
I have a similar issue. I have tried for over three hours now to understand why I cannot reboot into fastboot. It seems lika I have lost both fastboot and NVflash. Only RSD mode and a logo screen without text. Can't shut it down with powerbutton or factory reset. I tried to root it with a 3g boot.img whitch was terribly wrong on a wifi-only xoom and I'm now trying to flash a stock wifi boot.img. It just sits there on the M dual core screen.
What can I do from RSD mode 3?
EDIT: I have a feeling that it has freezed on that logo screen. I want to try a hard reset and the only way for me is to try to first shut it down then power it on again. Don't know if it helps but it is silly to be unable to stop it. How can I shut it down?
I've tried all the suggestions above with no luck
Will try a windows machines tonight to see if that will help, but I fear I will need to send my Xoom back to mfg for rework
may seem a stupid suggestion but what if you let the battery go dead. it will turn off. Then connect to power supply and do a fast boot restart, holding power button and vol down.
Just a thought!
I will try but I think I already tried that. It seems like boot and recovery is dead. I tried to flash the 3g .sbf file today. Thought that an already bricked tab couldn't be more bricked and perhaps it would restore the recovery or boot but RSD Lite couldn't do it. It's unvisible for a computer. I've tried both win7 and my Arch Linux box. The device is dead. Hopefully they wont have to replace the motherboard. I'm sending it for repair on Monday.
mines bricked also says
failed image lnx 0x0002
starting rsd mode 2
i can get it in the fastboot protocol mode with the - button and power but cmd window says waiting on device. my started after i did an fastboot oem lock with a bad kernel.
dogma444 said:
mines bricked also says
failed image lnx 0x0002
starting rsd mode 2
i can get it in the fastboot protocol mode with the - button and power but cmd window says waiting on device. my started after i did an fastboot oem lock with a bad kernel.
Click to expand...
Click to collapse
iirc the Failed Image lnx 0x0002 is due to locking the boot loader with custom stuff.
Unplug xoom usb
boot into fastboot
plug in xoom usb
fastboot oem unlock
orionshock said:
iirc the Failed Image lnx 0x0002 is due to locking the boot loader with custom stuff.
Unplug xoom usb
boot into fastboot
plug in xoom usb
fastboot oem unlock
Click to expand...
Click to collapse
Man that just sound to easy to work. ADB has no clue the device is.....wel, a device! Its like my xoom de-evolutionized to a primitive state and is suffering from tourrets. Anyway command typed in adb gives you back < waiting for device >. I've tried just about all the techniques here on the forums. And the people who claim to have been brought back to life are not victims of this "RSD mode 2" Im pretty sure this is like a failsafe if you blow up the original bootloader, 3. IDK though, pretty sure they are going to require some hardware replacements. Im not sure people are recognizing the degree of our bricks. These are what appear to be real BRICKS. no "soft" ness up in here. straight up cement
http://forum.xda-developers.com/showthread.php?t=1041192
adb wait-for-device && adb reboot recovery
tried this command and seemed pretty slick but, still nothing
Same thing here, was there any solution?
Give this a try:
http://forum.xda-developers.com/showthread.php?t=1079784
Please, I have same problem, but I can just reset it by pressing and holding Vol Up + Power On. When I press Vol Down + Power Down, nothing happens. If I press Vol Down when it restarts, it doesn't show me the message but shows the Motorola Dual Core logo and stops. Even in this situation I can't comunicate via usb. Now it just turn off when the battery is totally low.
I CAN boot into fastboot mode and issue fastboot commands from CMD. apparently mine is booting into RMD 3 mode or whatever it's called. when I boot normally (just hold down power button, I get the moto dual-core screen, and then it boots into the Clockwork Recovery Mod... PLEASE HELP

Stuck at Motorola logo and RSD mode 3

I'm new to Xoom but gave unlocking and rooting a go. That was todays mistake! I flashed a 3g version of boot.img. Then I tried to flash back to stock img-file. Found out that it also was a 3g img-file. Flashed once more. Now it was a wifi-only boot.img. Now I'm stuck at the Motorola Dual Core logo with Starting RSD mode 3 written in top left corner. I can't shut this thing off or anything else but rebooting back to same screen. I really don't know what to do. I bought it yesterday from a man that bought it in the US a week ago so I can't go to the shop and I don't think there are any shop that can flash it for me because it's not available here in Sweden yet. Please help. I have RSD Lite installed and the correct drivers for the Xoom installed. I'm used to ADB but it can't find the device and fastboot doesn't see it either.
Edit. I can't go into fastboot mode.
Grab the wifi's boot.img off of here:
http://forum.xda-developers.com/showthread.php?t=1017398
http://forum.xda-developers.com/showthread.php?t=973355
This might be helpful. Not sure.
Don't worry you are in good company, even BRD had the same problem. Here's how he fixed it:
While I was in "RSD Mode 3" I did
Code:
fastboot flash boot boot.img
Even though there was no response from the device, I pressed Vol Down + power until the screen went black. I then quickly pressed and held Vol Up + power. The device then went into the bootloader, received the queued command from fastboot, and flashed the boot.img. Finally, I did
Code:
fastboot reboot
and was back in the game.
Guys, I think the moral of the story is to slow down and be careful with fastboot. You can bet i'll be a little more careful
Click to expand...
Click to collapse
Edit: Same advice as linked above by milehighclubAV8R
That doesn't do it. Propably it's some stupid misstake from me but I cannot do this because of " I pressed Vol Down + power until the screen went black". It wont get black. When I press Power + Vol down nothing happens. Am I doing something wrong. I have tried holding the buttons for about 30 seconds and nothing happens.
Did you just press the buttons or did you also enter the fastboot code as suggested?
First cmd command then pressing the buttons. When I reboot using power + vol up it starts into RSD mode 3. When rebooting it with power + vol up then vol down when black it starts into the logo screen without any text in the upper left corner. Can't even shut it down with long press on power button
Can I pull the battery? On my Galaxy S that's the way out if I get in a boot loop or need to redo a failed flash.
Not AFAIK, the unit is sealed and can't access the battery to pull it.
Perhaps ask in this thread - http://forum.xda-developers.com/showthread.php?t=973355, there may be more technical people seeing it there than in the general section.
OK. I will do that. Thank you for trying to help.
Press power+volume up. Hold it til it restarts. Let go of both buttons once you see the motorola logo then just press volume down once, and you should be then able to cycle through 3 different modes. Press volume down to cycle to different modes, volume up to select. Hope that helps.
Sent from my Xoom using XDA Premium App
Sorry but I can't cycle through anything. There are two modes. Either "Starting RSD mode 3" or nothing and RSDLite can't communicate with it so I belive that my xoom is dead. Sending it in for repair tomorrow. I'm giving up.
mine is stuck in the rsd mode 2. if i push and power and the up it will boot cycle if i the down button it says it is the the flashboot protocol mode, but i cannot get it to respond from the cmd window. my computer doesnt think its connected. i have the correct mot drivers. any help or is it bricked
Some people have been getting lucky with ADB commands however others have not been so luck. I myself am in the others category with one of my XOOMS.
Sucks, but some people have been able to get back. I however have not been so lucky with one of the WiFi XOOM's I have and did this purposely to see if maybe something can be done with it. Looks like we have to wait for all the files to be released......
Any day now Moto, util then people will continue to send these devices in and con the stores . For this, I applaud them.
This might work or it might not.
I had a bricked xoom too. no matter what fastboot i entered it wouldnt recognise it. all it would say is "waiting for device"
This is what i did.
Turn the xoom off
Do not connect you USB cable yet
Fastboot reboot-bootloader
It should say "waiting for devices"
Now plug your xoom
Turn on the xoom.
When you see the Motorola logo press volume down till you see "fastboot protocol"
Press volume up.
It recognise my xoom that way
couldnt turn mine off. let the battery run down. plugged it into power booted it up. no help. bricked
stevenege said:
Some people have been getting lucky with ADB commands however others have not been so luck. I myself am in the others category with one of my XOOMS.
Sucks, but some people have been able to get back. I however have not been so lucky with one of the WiFi XOOM's I have and did this purposely to see if maybe something can be done with it. Looks like we have to wait for all the files to be released......
Any day now Moto, util then people will continue to send these devices in and con the stores . For this, I applaud them.
Click to expand...
Click to collapse
I have to admit, I'm one of them. Sure is a nice way to tell Moto to hurry the F up. I can't say I felt great about it but I wasn't about to lose $600 either.
me to one of them
shipped mine back to the factory today. not sure what they can do to it. is there such a thing as a force flash or will they have to replace the firmare chip to make it work? unstable combo tegra and honeycomb, aint messin with mine anymore.
i just recovered mine from this. i flashed recovery with clockwork mod:
at the rsd 3 screen with the usb attached
fastboot flash recovery recovery.img
held the volume down while pressing the power off on until fastboot started flashing the recovery
fastboot reboot
xoom started in clockwork mod, did a restart and it worked
****This happened after attempting to load recovery from rom manager without flashing new recovery image.***
Did you happen to mention in your explanation about what went wrong with your xoom anything about unlocking or relocking?

[Q] bricked HTC Hero 200 please help

I got a used HTC Hero 200 yesterday, and it only took about 1 hour for me to brick it.
I ran "Universal Androot" to get superuser permissions, then I overwrite the files "boot.mp3" and "hero_animation.gif" (I think they were somewhere like /system/media/bootanimation) in a failed attempt to change the boot animation. After resetting, the screen just displays the HTC logo for about 30 seconds then goes blank... so Im guessing my boot animation screwed it up.
When I boot to recovery mode (with the triangle and "!") using PWR + HOME buttons, I can see the option "Wipe data/factory reset [Alt + W]" and I can highlight this option with the trackball, but I CAN NOT click on it. Also, the phone has no keyboard, so I can not press [Alt + W].
When I boot into fastboot (with the skateboarding androids) using PWR + VOLUME DOWN buttons, I plug in USB and the command "fastboot devices" finds my phone (but "adb devices" cant find it).
Is there a way to get this phone working again?
Im new to Android, and Im easily confused. So if anyone can help me through this, Id appreciate it. thanks.
You're more likley to get a better responce in the Hero section however, I'm like 90% sure you will be able to fix, And technically not bricked
But, perhaps an RUU from HTC could help to fix
THANK YOU MAX!!!! that was all I needed. I downloaded the RUU from the phone's old service provider (cellcom) and just executed it as an administrator whilst in fastboot usb mode. everything works great now, and Ive even got a newer version of Android... except it reinstalled that same lousy boot animation...
Anytime dude Glad you got it working again!

PCEU Ransomware

I have managed to get the PCeU Ransomware onto my Tab and now when I turn it on i immediately get the splash page asking me to pay up.
No matter what i do to try to get into Safemode or Recovery Mode it is no good I simply get the splash page up which prevents me getting any further in my attempts to remove it.
Any suggestions would be gratefully appreciated.
I forgot to add that the usual method of getting into recovery is as far as I know the power button and volume up after turning the device off first (I have tried up and down volume as well)....i feel however that the device never completely turns off as when I hit the turn off option on the lock screen it shuts down but i dont feel the vibration that i used to get when it did this.
Trasnadunta said:
I have managed to get the PCeU Ransomware onto my Tab and now when I turn it on i immediately get the splash page asking me to pay up.
No matter what i do to try to get into Safemode or Recovery Mode it is no good I simply get the splash page up which prevents me getting any further in my attempts to remove it.
Any suggestions would be gratefully appreciated.
I forgot to add that the usual method of getting into recovery is as far as I know the power button and volume up after turning the device off first (I have tried up and down volume as well)....i feel however that the device never completely turns off as when I hit the turn off option on the lock screen it shuts down but i dont feel the vibration that i used to get when it did this.
Click to expand...
Click to collapse
Try to force reboot recovery by using "adb reboot recovery" and wipe data and cache from here. If you want you can save data from TWRP
Greets
If you can get to download mode and reflash stock rom, it might work!
Cant get to download mode unfortunately. Is there any idiots guides for instructions for "adb reboot recovery"?
Scratch the above.. I found the above and was able to run the command prompt but the device does not appear to be found and when any command is run i get error: device '(null)' not found.
I can see the files on the device in Windows explorer however so would have assumed the drivers when correct.
I suspec the issue is that I cant get into usb debug because i cant get past the blasted ransomware splash screen.
Trasnadunta said:
Cant get to download mode unfortunately. Is there any idiots guides for instructions for "adb reboot recovery"?
Scratch the above.. I found the above and was able to run the command prompt but the device does not appear to be found and when any command is run i get error: device '(null)' not found.
I can see the files on the device in Windows explorer however so would have assumed the drivers when correct.
I suspec the issue is that I cant get into usb debug because i cant get past the blasted ransomware splash screen.
Click to expand...
Click to collapse
Hard boot into recovery and then factory reset. Vol Up + Power until screen pops up then keep holding just volume up.

Categories

Resources