WiFi problems at work - Captivate General

I believe that the Captivate does have a WiFi problem. It works just great at my house with 1 Linksys/Tomato router (WPA2, AES, pure-g). At work with 3 HP Procurve 420 APs all set with (WPA2, AES, pure-g) the captivate will connect just fine to the first AP won't roam to any others. When I walk across the building it doesn't properly switch to the closer AP. All of our laptops and iPhones will do this just fine. The solution for me is to turn off wifi, then turn it back on when I move locations. Its a pain, but not a deal breaker for me. FYI all of our HP Procruve APs are set on different radio channels, same SSID, same security (WPA2, AES, pure-g mode).
What is your WiFi experience at a locations with multiple APs?

Related

Wi-Fi roaming between access points

Hello,
Has anyone else noticed problems with their Wi-Fi not properly jumping to the nearest wi-fi access point when you move around a large office or campus? I am the IT manager of a small company and we have 3 access points. I need to turn off wifi and turn it back on to connect to the nearest AP with walking around the office. Our laptops and iPhones do not have this problem. The three AP each have the same SSID, WPA2 encryption, but different channels that do not overlap. What gives?

[Q] Wifi issues

My wifi is very spotty at best. It always seems to say it connects just fine but it won't let me actually use it. I just went and stood right above my router and had full wifi strength and couldn't browse the internet. Are there any solutions to wifi issues or do I probably just have a bad wifi chip?
There could be a ton of different reasons why you can't connect. There might be a compatibility issue (some devices just don't get along), there might be an issue with security (you aren't using WPA2/AES on your router), there might be a channel issue that can be fixed by trying another channel on the router, the list goes on and on.
What kind of troubleshooting have you done so far? What router do you have?
Running a netgear WNR3500L with WPA2 encryption. All I've done so far is a simple restart of the router.
EDIT: downloaded and used wifi analyzer to see which channels were open and they looked to all be about the same. I switched it to 6 for tests without any improvement. My router auto detects the best channel to be on. Any other advice?

Wifi does detect one network while not the other

I observed a very starnge thing with my new htc one x. The wifi works fine but does not catch all the wifi in the area. To be clear. My phone connects at work to university wifi and the signal remain rock solid.
But At home it will not detect my onw home wifi, while it detects many others from the neighbours. Is there a way to solve this issue.
Thanks
Have you tried simply power cycling your WiFi router?
Also, try a different security type on the router. For example if its set to WPA, try WPA2, or vice versa. If its WEP, try WPA or WPA2. WEP in particular is not recommended, as its not very secure, and I believe does not play well with our phone.

[Q] Wifi connected, no internet

OK, I've searched Google for weeks and searched the Xoom Q&A, but don't find anything that addresses my problem.
I have a network with one router connected directly to the cable modem. It is called Jaytrenthome. Connected to that via cable is another router in AP mode called JText.
My Xoom connects successfully to both, but only shows blue bars when connected to the JText AP. When connected to Jaytrenthome, it shows Wifi connection, but grey icon indicating no internet connection.
As the routers are on different sides of the house, I need to use both depending on the side of the house I am on.
details about the routers.
Jaytrenthome
WD Mynet N900
2.4 Ghz, WPA2 Personal, 802.11 B+G+N, no selection found to pick AES or TKIP
DHCP active on this router
JText
Netgear WNDR3300
2.4 Ghz, WPA2 PSK (AES), 802.11 N, DHCP turned off, IP address provided by Jaytrenthome
Xoom Details
Xoom Stringray (4G)
Running Baked Stingray rom BB-8
Same problems experienced with EOS and one of the CM variants
4G works flawlessly.
Things I have tried so far.
1. Changing Xoom time update setting to not update automatically.
2. Changing WIFI settings on Jaytrenthome to WPA, WPA2, WEP, etc... with no luck.
3. Turning on the 5 Ghz band of WIFI on Jaytrenthome.
4. Assigning a fixed IP in the Xoom WIFI settings
5. Praying....
Can one of you help from a similar experience?
Thank you!
Sad face...
>70 views and no one has an idea to help me with this.
Thank you for looking, though.
coolbeans8 said:
Can one of you help from a similar experience?
Thank you!
Click to expand...
Click to collapse
Are you using the same SSID and password for both the routers?
My Xoom did not like it when I had a router and AP broadcasting using the same SSID (and same password) in my house, although my issue wasn't exactly the same as what you're experiencing. For me, the Xoom had a really hard time staying connected to either of the units if the signal strengths were very similar. The signals seem to fluctuate quite a bit in my house, with the strongest signal bouncing back and forth between the two routers, so I ended up with a lot of disconnects and sometimes a long time to authenticate. I ended up moving one of the routers to a better place in the house and eliminating the second one. I'm now getting more reliable connections, particularly if I use the 5 GHz signal. Ultimately I still think there is something interfering with my 2.4GHz signal though, but I haven't had a lot of time to troubleshoot further....
Fixed!
slow1234 said:
Are you using the same SSID and password for both the routers?
My Xoom did not like it when I had a router and AP broadcasting using the same SSID (and same password) in my house, although my issue wasn't exactly the same as what you're experiencing. For me, the Xoom had a really hard time staying connected to either of the units if the signal strengths were very similar. The signals seem to fluctuate quite a bit in my house, with the strongest signal bouncing back and forth between the two routers, so I ended up with a lot of disconnects and sometimes a long time to authenticate. I ended up moving one of the routers to a better place in the house and eliminating the second one. I'm now getting more reliable connections, particularly if I use the 5 GHz signal. Ultimately I still think there is something interfering with my 2.4GHz signal though, but I haven't had a lot of time to troubleshoot further....
Click to expand...
Click to collapse
Thank you!
I had the ssid set differently, but the same password for each. Your post got me to try changing the password so each ssid uses a different one and voilĂ .
Woo, hoo!

Wifi roaming bug is back on S7

I have two wifi APs with the same SSID and it will stick to one of them with next-to-useless connection while standing near the other one. which would have much better connection.
This works fine on my Nexus 9 tablet and even better on my iPad and my wifes iPhone..
I tried some possible workarounds like Always allow wi-fi roam scans but I didn't see any effect.
This fix for SG3 might work but i havn't rooted.
Even more solution suggestions
Doesn't this bother anyone else ?
wifi has a bug in 6.X and its been talked about before.
my problem some times when i want to connect to another wifi it connects for a 1 sec and then drops it
i turn off wifi and back on and it will connect
i'm trying the app "Wifi roaming fix" but i think it causes the wifi to disconnect for a couple of seconds when it switches.
Strange that this seems to be of no interest to anyone. Is there indeed nobody who is using one or more WLAN APs in addition to his/her WLAN router? I can't believe that.
I have two APs (Main router and 2nd router as AP) but not for more coverage, my main router pushes 5GHz wifi, the second AP pushes 2.4GHz for older clients that can't connect to 5GHz
The 5GHz router is placed on a wall in the middle of the house and the entire house has great coverage so no need for more APs
I have more APs in my house with OpenWRT and 802.11r aka Fast Roaming configured and roaming between all my APs is working perfectly with all my devices.
Note 10.1 2014 Wifi, S7 Exynos and all other also.
With APs configured as "normal" ap with the same SSID and key i had the same issue as you mentioned.
I think your phone dont know that it could roam between your two APs.
If you could not run OpenWRT on your APs for 802.11r, you could try to enable WDS on both APs even if your APs connected by wire.

Categories

Resources