[Q] Vibrant brick - Captivate General

I've got a vibrant that was running the stock rom. I tried applying the lag fix posted on this site and ended up in a boot loop. I started walking thru the odin recovery process and rebooted the phone out of download mode when nothing was progressing after 20 minutes.
Now I have a vibrant that does nothing but show a little cell phone next to an exclamation point next to a pc. Three hours of attempting to get it back into download mode with every conceivable combo of volume up down and power do nothing. Pulling the battery to power it off then plugging it into either a USB pc connection or a wall charger fails to show the battery charge screen. All I can get this phone to do now is show that phone ! pc image. Any ideas?

Why didn't you post this in the Vibrant section of XDA?

Related

[Q] Cannot get download mode - HELP

I was trying to get 2.2 on my captivate. It got hung and after about an hour, I powered down phone (battery out).
I'm now getting [phone... (!).. COMPUTER] picture
Trying to get back to stock ROM 2.1, but I cannot get device in download mode
I had to use adb to get in download mode originally.
Is it possible I got a phone that doesn't go into download mode based on button combinations? If so, what do I do?
Unplug your phone from USB
Pull battery
Close Odin
Open Odin
Put in battery
Hold both volume buttons (NO POWER) and plug in USB
Hopefully this gets you into download mode
Still Fail
I've been trying that, but without open/close of Odin.
Still failed when I added that step.
get to that screen again: hold volume up/down and power at the same time.
When the screen goes black, then release power button but keep holding down volume up/down
Zilch25 said:
Unplug your phone from USB
Pull battery
Close Odin
Open Odin
Put in battery
Hold both volume buttons (NO POWER) and plug in USB
Hopefully this gets you into download mode
Click to expand...
Click to collapse
Yes, and remember to keep the volume buttons pressed in while plugging in the USB... I always hold them in until the droid/caution sign comes up.
alabamaroping said:
I was trying to get 2.2 on my captivate. It got hung and after about an hour, I powered down phone (battery out).
I'm now getting [phone... (!).. COMPUTER] picture
Trying to get back to stock ROM 2.1, but I cannot get device in download mode
I had to use adb to get in download mode originally.
Is it possible I got a phone that doesn't go into download mode based on button combinations? If so, what do I do?
Click to expand...
Click to collapse
Try the methods prescribed. There are several minor variations but you may have a phone that doesn't do three button recovery. In order to tell, we need some history on your phone. What is the RF Cal date? Were you able to three button into download before? Do you know if it was one of the ones that had the three button problem?
autocorrelation,
I tried that with the usb cable plugged in and without it plugged in.
Still no good.
joeybear23,
I've been trying that all afternoon. Probably about 50 times.
ianwood,
How do I get the RF Cal date? I don't see it under the battery where the S/N is located. I tried to do 3 button recovery to put phone into download mode when trying to install 2.2, but it wouldn't work. I had to use "adb reboot download".
I've never tried it before today. The only issue I've had was that it could NEVER connect to AT&T server to check for an update.
can you get it into recovery mode?
no recovery
No. It won't go into recovery mode either.
The only thing it WILL do is respond to all 3 buttons being pressed by the black screen flash after about 8 seconds.
If you keep holding all 3 buttons will it flash again after the initial black screen? Try releasing the power button and keeping holding vol up/down after the second black screen.
If I keep holding all 3 buttons, it just keeps flashing.
Also tried to let it flash twice (and even more) and releasing power right when it goes to black 2nd (or 3rd) time. Also tried releasing power half way through black screen, and right before black screen re-appears and also just as the screen powers back up. None of them work.
I ran into this yesterday and about freaked out. Don't panic - apparently one of the guys had this happen to them a lot. Take a deep breath, have ODIN open, plug your USB cable in, hold the volume buttons down at the same time, press and hold the power button till you see the phone to computer, and let go. You should get to the download screen again. Good luck; sucks when something like that happens and you don't know what's going on.
I know this wont help much, but I have one of the no 3 button phones, and after 20 minutes of trying all these methods, it did go into d-load mode. Unfortunately, I don't know exactly which combo I used since my brain went into overload when I finally saw the triangle appear. There is hope though, and please PLEASE post which one works for you(I'm afraid to mess with mine until I find a foolproof method)
I had a phone that wouldnt respond to ANY 3 button combo I tried. I bricked it (sorta on purpose) to the phone-!-computer screen and went and replaced the phone at AT&T (under the 30 day deal).
It didnt initially work with the 3-button but after the JH7 OTA DL mode and recovery mode work perfectly now. Also, GPS has been completely spot on when testing on my motorcycle with the phone in my backpack running my tracks.
If you are under the 30-day return policy, bring it in and come up with a good reason as to why they should give you a new phone. If not, then you're sorta SOL....
Zilch25 said:
Unplug your phone from USB
Pull battery
Close Odin
Open Odin
Put in battery
Hold both volume buttons (NO POWER) and plug in USB
Hopefully this gets you into download mode
Click to expand...
Click to collapse
This method just saved my butt!!!
I have never had trouble getting into recovery or download mode until today when I did a dumb thing. The phone would lock at the ATT screen when trying to power on and if the phone was off and I plugged it in to charge it would freeze and the circle logo that comes up before the green charging battery does.
Every method of getting into download or recovery failed up till now.
Thanks Zilch!!!
Hey guys gonna move this to Q&A.
I had this problem a few days ago after updating to 2.2. I tried every single button/usb/battery combo and nothing worked. FORTUNATELY I was within 30 days of purchasing it (I guess there's a silver lining when diving right into "hacking"), and I brought it to the store with the box and receipt and just told them it gave me an error when turning it on (played dumb) and they swapped it out without even testing. If you're over the 30 days then I think you're pretty much SOL... gotta pay for a replacement.
bricked
I declared it to be bricked and took it back to the store. I have only had it 2 weeks, so I basically pulled the same move of playing dumb and they gave me another one without any problem.
I'm wanting to try to see if I can put it in recovery mode and/or download mode with the buttons without even attaching it to anything, but now I'm paranoid about bricking it.
itsjustaphone said:
I know this wont help much, but I have one of the no 3 button phones, and after 20 minutes of trying all these methods, it did go into d-load mode. Unfortunately, I don't know exactly which combo I used since my brain went into overload when I finally saw the triangle appear. There is hope though, and please PLEASE post which one works for you(I'm afraid to mess with mine until I find a foolproof method)
Click to expand...
Click to collapse
Buddy, we need you to remember I'm in the exact position, no combo works and I bricked it after trying to load 2.2
Going into recovery or download will not brick it, its only everything after that point that might get you bricked.

[Q] Samsung Galaxy Captivate (Rogers) not booting

This is my first post on the boards, so I apologize in advance.
This phone belongs to a friend of mine, they had it rooted and then they reset it to factory default, and it stopped working. That's when it was given to me.
Specs:
Samsung Galaxy Captivate (Rogers)
SGH-I896
When I got the device, it could be turned on and would say "SGH-i1987" and "19000i" or something. After a short time an "S" would appear and glow until the screen went idle. It would never boot up.
After a lot of trial and error, I eventually got it into download mode by holding VOLUME DOWN and clicking the POWER button.
Once on, I tried flashing using a One Click Odin from this site. It seemed to be installing through Odin and eventually the device booted up an "AT&T" logo then rebooted, and kept doing so over and over.
After 5 or so minutes, I hit the power button and Odin said 1 Successful/1 Failure ( i believe) and so I unplugged the device.
Now when I turn it on it keeps loading the AT&T logo and then rebooting, or if I connect the USB it shows the grey battery, then reboots.
Here I have tried everything. I tried VOLUME UP + VOLUME DOWN, VOLUME UP + VOLUME DOWN + POWER, VOLUME DOWN + POWER, USB, no usb, I tried 10 times doing each. I could never get a different result.
I bought 3x100k resistors and tried linking them, ran it over a meter and say that it had 300k resistance. I tried making contact to the microUSB slot but after a few hours it still hadn't gone into download mode. I stripped a microUSB plug but I had to junk it, the contacts weren't helpful. I've since ordered a USB jig but would like to fix the phone before that comes in, if possible.
Is there any other way to fix it other then the jig, is the jig going to help? I have a microSD card, can I use that to enable the buttons or flash something helpful onto the device? I don't have much experience with this but I've read several forum posts on the subject so far. Also, if I get it into download mode, what is my best course of action to get a simple WORKING OS loaded.
Thanks a lot for any help you can offer me!

Phone will not boot into recovery

My phone is rooted with stock rom. The only changes are listed below
Froze bloat that was safe
changed bootanimation to stock samsung
replaced some apps with inverted versions of themselves (ex. google +, stock messaging)
Here goes:
I was using navigation and I noticed that my phone was off after I had finished. Nothing worked at all, I could not boot into recovery or download. I connected the phone to a charger and red led flashes and an empty battery appears. The battery was full. I could reboot the phone while on the charger, but it would shut off as soon as it got to the homescreen. While off, If I pressed the home button, the green battery would appear as if it were charging. From here I could boot into recovery and download mode. The phone will only boot into these modes while connected to the charger. Here is where it went bad. I attempted to restore a backup while the phone was on the car charger and my car charger got pulled out in the middle of a restore. No charger meant that the phone shut off mid restore. Now, when I plug in the phone, the red led appears and the empty battery with a circle inside appears and then goes away. This repeats itself over and over and the phone buzzes when the empty battery reappears. I can still boot into download mode but not recovery. If I try to flash the stock samsung rom via odin, it says that it passes, however upon automatic reboot the samsung appears and nothing else. After the samsung appears the phone just continues to buzz every 5 seconds or so as if it is trying to do something. Could it be a bootloop? I have done a ton of searching here and now I am resorting to help! Your time is appreciated and beers on me if you can help me get my phone back to normal.
What Rom/kernel were you using before this happened? If custom, which one?
I have another thread a few posts down with the same topic. I am going to delete this one. I was stock rom and kernel. For some reason the phone will not recognize the battery. I tried a new one at verizon and the same thing. I can now boot into both recovery and download mode when connected to the charger , but the phone shuts off as soon as it boots and shows an empty battery with a circle in the middle. Sometimes it does not make it through the verizon boot animation and sometimes it makes it all the way to the homescreen and I can make a few selections before it turns off. After flashing the stock kernel and rom in odin I believe i am completely stock, however I do not want to chance sending the phone into Verizon. I believe that I saw a thread before this happened to me talking about having to calibrate the battery in some way and it had an item to flash in order to fix the problem. I can not find it now. Any ideas? Now that I can access recovery is there anything else that can be done? Why won't the phone recognize that it has a battery? As soon as I pull it off the charger it shuts off. When it is on the charger it appears to be charging and the green in the battery appears to be at about 80% but the level does not move up or down at all. Thank you for your help ahead of time.

[Q] HTC Sensation 4g died and won't come back on

I just did a factory data reset yesterday and I was calibrating the battery for the new ROM. When I let the phone die all the way, I left it unplugged for a little while because I was in the middle of a movie. When I got around to plugging it back in, I am getting a flashing LED, no charge indicator, and it won't boot up. Every once in a while, the HTC boot logo will pop up and my phone will vibrate like it's turning on, then it will just go back to the flashing LED. I can get it to jig into fastboot ever so often, but when I try to boot into recovery from there, it just turns off and goes back to the flashing LED. Everything I have read says to hook it up to my computer and use ADB to reboot it, but when I bring up the command prompt, it says that ADB isn't a recognizable action or something like that. My laptop also doesn't recognize my device as being plugged in. I've perused the forums on here and to no avail so here I am asking for help... HELP!?

black screen after downloading custom os from odin due to update

Okay, here is the problem. I have looked around, and this thread seems to be close to what I initially ran into.
http://forum.xda-developers.com/showthread.php?t=2199042
What seemed to cause this was some sort of update verizon was telling me to download, and I kept deferring it until I accidently hit yes. After hitting yes and the update going through, the phone booted to "System software not authorized by Verizon Wireless has been found on your phone.”, which would force me to restart.
If I used odin's button patterns, I would come across the mentioned route in the thread.
But the route I went (because I assumed it would work) is download what was prompted as a "custom os" as opposed to denying it and (I'm assumed based off the thread just posted) starting the phone up. After an hour long car ride, leaving the phone alone and apparently "downloading" the custom os, my phone turned off.
Now what I am facing is only a red led when charging (which is normal when charging while off), but when using any odin button pattern, my phone simply vibrates and nothing more. Nothing on the screen, even when pressing the power button itself. It just stays pitch black. I have no clue what has happened. Any possible suggestions? I tried with battery out, charger in as well as battery in, charger out, and charger in, battery in.
If you plug the phone into your computer and power it on/attempt to enter Odin, does your PC recognize it?
frankspin said:
If you plug the phone into your computer and power it on/attempt to enter Odin, does your PC recognize it?
Click to expand...
Click to collapse
Actually, plugging it into my computer just keeps making it vibrate as if it is starting to power on. I can't even get into odin or even a screen coming up for that matter.
Hey thanks for the help! I figured it out. I guess the battery was incredibly depleted from leaving it in download mode in odin. I charged it up and after a few hours, the power came on. I followed the guide in the thread I posted and it worked like a charm. Sorry about the confusion and I greatly appreciate the help. Thank you!

Categories

Resources