Database Info

Wont Boot

I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks

Drunknasty said:
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Click to expand...
Click to collapse
if your device is G3, unlocking is required to flash any rom, before upgrade your device, it is recommended to flash an official WM5.0 rom (in your case T-Mobile rom) with IPL and SPL 2.xx then flash again.
in general there are many probabilities for your issue.
((Where is TNT1.1?? did you mean 1.0?? ))

My Bad meant 1.0
So to get it straight.... I will need to unlock my phone each time?
Oh and to correct myself again, when flashing with the T-mobile ROM it says UPGRADE ONLY. And the read me file says its the wrong RUU. But it is the same file from Tmobile I used when I first got the phone. But I will try again.
Are there any other suggestions?

You need to read the "how to flash" sticky.

I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.

Try another ROM.

Sounds like you need the "Wizard Love" rom. I dont have the link handy but I am sure someone else does.
Drunknasty said:
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Click to expand...
Click to collapse

Already got it. Thanks I am trying to load it now. But the only thing is that the last time it failed and I can understand what the error says. I know the number is 300 but can read the language.
But I will let you guys know when this load completes.
Thanks again for all the assistance.

No worky worky. The load completed and then boots the splash screen shows and then stays there.
Any ideas?

Try to remove the battery and let it out for at least half an hour. Then put it back in and see what it does then.

I thought the same thing too. So when it got done last night, out of frustration, I removed the battery and left it there to wait on when I get off work today. I will report back on what happens.
Again I would like to thank you guys for helping me. I really do appreciate it!

STEP 1 install the original manufacturer ROM
T-mobile UK
http://www.tm-phonedownloads.com/download_manager_mda_vario.html
T-mobile US
http://www.t-mobile.com/wmupgrade/
Search for the original rom for any other
instructions on how to use the original rom can be found here
http://support.t-mobile.com/knowbase/root/public/tm23294.htm?&A2L.SERVICE=AboutUpgrading
Put it in the bootloader mode.. ( three color screens )
hope this helps..
cheers
Praneet

Ok I did that and it gave me ERROR 296: UPGRADE ONLY
Then it tells me that the NBF file cannot be used for my PDA Phone. Please get newer NBF file.
Is there any way I can get the Tmobile splash and IPL\SPL number back to original, it doesnt need to boot all the way into WCE but atleast show the same numbers and splash during boot up?
Or any other way to get this thing to work?
Thanks guys
BTW it is a HTC Wizard from T-mobile.

If you are getting an error 300 you need a newer rom update utility, and regardless if your phone is a G3 or G4 it needs to be unlocked before you flash any rom.. LOAD a OFFICIAL cingular ROM onto your device before going any further, then unlock your phone either via www.imei-check.com or through some of the tools offered here...

Which one should I down load from Cingular? Even though I have a Tmobile phone?

what ipl and spl are you using and what radio are you using. Just post all the numbers from the bootloader

As soon as I get home, I will post them.
Thanks

Ipl 1.01
Spl 3.08
Thanks

Drunknasty said:
Ipl 1.01
Spl 3.08
Thanks
Click to expand...
Click to collapse
uh oh. someone tell me if I'm wrong, but I think this is bad. it's the result of flashing a g4 with g3 or the other way around... keep searching, and good luck.

flash the original t-mobile rom. your phone doesn't appear to be unlocked. good luck

Flash without hardspl

I have an unusual problem with my oem att tilt running SPL-1.56.0000 (according to the bootloader screen).
The ROM is somehow corrupted in that it will not boot past the giant ATT logo and coordinates (?) screen. I have been having some trouble with the device, but this is a new occurrence not related to anything I did. I have never reflashed the ROM, and because it is in a current hosed state I cannot run hardspl on the device.
I have tried reloading many of the "ATT OEM" ROMs I can find, but they all return "Invalid ID" error the ROM uploader I believe because the versions don't match.
Is there any way to reflash the ROM and bootloader on the device without having first run hardspl? Am I SOL?
Thanks
RK

Did you try going to tri-color first then flashing a stock tilt rom?

Dude, I have the same problem...
I bought the tilt 2 weeks when I was in a business travel in the US and came back to Argentina... I'm kind of screwed about the warranty 'cause I don't think I'll go again so soon to the US...
Is there anybody who can help us with this?
The very diference is that (At the ATT start up Logo screen) the bottom line says D 1.57.00.00 instead of D 1.56.00.00.
Tried everything... soft reset, hard reset... and so on...
The thing is that at some point I think I can get to the phone in some way since if I turn on the phone keeping pressed the camera button and enter in the rom loader screen I can get comm to the phone using mtty (As pof explained to do for "Un-brick" the phone (In the case you got a bad flashing) in this thread...
So, please If anybody have any idea it would be great!
I still have a little hope, because it's like there is some kind of communication between the phone and the computer...
Thanks in advance to any help.
A.

both of you...
Check my sticky thread for reverting back to the stock tilt ROM and SPL...
all you really need from there is the Stock ATT ROM... download it!
Put your phone in Bootloader (shouldn't be too difficult by the sounds of it)
Install the stock ATT ROM.
If this doesn't work try extracting the downloaded ROM (using WinRAR or similar) then just run the ROMUpdateUtility.exe
Then you might want to consider installing HardSPL... the default download should work for the 1.56 guy. The 1.57 guy will need to download jwocky2001's whitescreen fix (check the stickies).
Good Luck!

I am at the tricolor screen and I have tried the instructions on your thread (thanks very much for making it so easy). However, it says invalid vendor ID after loading 1%; the device automatically reboots and reverts back to the ATT screen until I place it back into the tricolor bootloader again. I thought this was because the version I'm running is 1.56 and I could only find two original OEM ATT ROMs, neither was 1.56 and both failed.
BTW I couldn't do the part about hardspl and running the kaiser program on the device for obvious reasons, but I could get the kaiserruu program to recognize the device, another ROM and attempt to upload it.
Any other thoughts? Do I really need the exact same ATT OEM ROM as what is on the device or is something else wrong?
Thanks again
RK

Reverting to official RUU with HardSPL

I have been searching all over for this but it's probaly right in front of my face. I read that you need to get rid of SPL.nbh from official ROMS before flashing back with HardSPL. The problem is, the official T-Mobile Wing ROM that I downloaded is an .exe file. How do I go about removing the SPL.nbh file since it doesn't display folder contents or anything, just runs the RUU?
Sorry for the double post, I realized I was in the wrong forum

flipside123 said:
I have been searching all over for this but it's probaly right in front of my face. I read that you need to get rid of SPL.nbh from official ROMS before flashing back with HardSPL. The problem is, the official T-Mobile Wing ROM that I downloaded is an .exe file. How do I go about removing the SPL.nbh file since it doesn't display folder contents or anything, just runs the RUU?
Sorry for the double post, I realized I was in the wrong forum
Click to expand...
Click to collapse
I'm uploading a zip file which will have the entire thing already to go.
Just flash your device as you would with any other rom.
Hang tight the link will be available within 10 mins.

Thank you sir. Greatly appreciated

flipside123 said:
Thank you sir. Greatly appreciated
Click to expand...
Click to collapse
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.

One more question. I'm looking to keep HardSPL but I have to revert to original to upgrade ROMS don't I? I want to upgrade to your OT 6.5 ROM

flipside123 said:
One more question. I'm looking to keep HardSPL but I have to revert to original to upgrade ROMS don't I? I want to upgrade to your OT 6.5 ROM
Click to expand...
Click to collapse
Okay,
I thought you wanted to go back to the original T-Mobile rom.
If your trying to HARD-SPL your device to install one of my roms or another cooks roms then thats another story.
Please read my FAQ or one of the stickies.

Ok, I think I got it now. So I don't need to revert to the original ROM to flash it since I have HardSPL? Thanks for the help

wen i did this i think i bricked my fone now its at the tmobile screen and it jus staying there

I tried the file that you uploaded here...And it went thru the whole process of flashing the ROM, but after it updated my wing just stays on the T-Mobiel screen and never boots past that.
It had that open touch software on it and I don't want open touch. I want plan old WM 6.0 on there.
I called T-Mobile and got an offical 6.0 update from them, but when I try that one it gets to 1% then says it has a disconneted and I get a connection error.

ttran001 said:
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
Click to expand...
Click to collapse
So does this work? The two people who did this had problems. I need the phone to be all stock so I can have t-mobile send a free replacement because the screen is going on this wing.
***EDIT:*** Oka so this is the same as http://forum.xda-developers.com/showthread.php?t=364543&page=2 the first time I tried it it froze at 15% on step 2 so I installed the RAPI CAB like it says. Step two completed, phone rebooted and had white screen then I got error 260 I think. I have the stock t-mobile rom on it and had it on before I did this but it still has the yang from when I did a hard spl. Is there another way to get it to stock or am I doing something wrong? Plug in phone, let it sync, run herald-uspl.exe hit enter and so forth.
***EDIT*** Ok so this time it completed but is now stuck at the T-Mobile screen and I am now unable to even flash because I can't get past it And that damn yang still shows up in bootloader. Well went into bootloader and flashed from there so phone works but the damn yang is still there. And on a side note: Has anyone ever had a problem with their screen going very dark after flashing a rom from here? Phone was fine then I flashed OTP v7.4 TouchFlo 2D Lite.nbh yesterday and at night screen started going dark, would light up when opened in keyboard mode, then switched and then both were very dark and hard to see. I then flashed to OTP v7.3.1 TouchFlo 2D Final.nbh and still dark. Then I flashed to stock rom and have been able to see the screen since.

This is stupid easy to do... im shocked there isnt a post going into detail.
5 steps to going back.
http://forum.xda-developers.com/showpost.php?p=2998657&postcount=4

smokeingit said:
This is stupid easy to do... im shocked there isnt a post going into detail.
5 steps to going back.
http://forum.xda-developers.com/showpost.php?p=2998657&postcount=4
Click to expand...
Click to collapse
Did not work. Do I need to install the cab files again? I know I deleted a file out of the stock rom so it would not overwrite or verify or something but I put that file back, should I not have? This has been a few weeks and still can't get the yang off. Screen on my girls phone is almost dead, she can't even slide it any more so I need to fix the spl so I can send back to t-mobile....anyone ?

this is what i do to get back to the tmobile orginal. download the software from tmobile. I downloaded the newest update from tmobile site. REMOVE YOUR SD CARD. Connected my phone via usb. Launched the update. It has never failed me yet. It is just like updating your phone. tmobile has to take it, it is their update. They sent me a new phone noproblem, matter of fact i have to do it again, the back on the phone keeps getting loose on me. so they are sending me another phone again. hope this helps.

Alternatively you can use the combination of uspl and stock rom ruu to return your device to stock tmobile rom...
1. Enter in to uspl like you were falshing one of ttran001 roms... You can get this HERALD-USPL-beta3 from http://rapidshare.com/files/79249048/Flash_Center.rar
2. ONLY use steps 1 and 2 from the black screen (getting the white screen on your device)...
3. For step 3 in the flasher exit out of the black screen (windows cmd screen) by pressing ctrl+C...
4. Fire up the official ruu from tmobile found here http://forum.xda-developers.com/showthread.php?t=358030 or alternatively if you have a tmobile account still active you can get the most up to date rom from http://www.t-mobile.com/wmupgrade/
5. Fallow on screen instructions...
6. Back to stock rom...

Brick dopod C858
ttran001 said:
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
Click to expand...
Click to collapse
Hello freind,
I have been downloaded the above "Remove_HARD-SPL_On_The_Wing.rar" files and flash it to my Dopod C858 which has the Chiness language, I suppose to change the language from chinesse to Englis, After flashing the above files, now the phone is only in bootloader mode.
If you start the phone it will stuck on white screen and turn off.
Please help me how to revive my phone back.
Thanks and best regards
Jhemzz

Hey I'm having the same problem as most of these guys who tried the file. The phone just idles on the white Tmobile screen... does anyone know what to do or how to help?
Please and thank you!

angest90 said:
wen i did this i think i bricked my fone now its at the tmobile screen and it jus staying there
Click to expand...
Click to collapse
im having the same problem can anyone help me please?

hotsammysliz said:
im having the same problem can anyone help me please?
Click to expand...
Click to collapse
Being stuck at the Tmobile screen isn't a true brick. Just reflash your ROM. (If you're not HardSPL'd, reflash your RUU.)

Remove Hard SPL from bootloader
Hi,
Anyone out there knows if we can remove hardspl from bootloader of Wing. Problem is my mobile displays splash screen, then switch offs by itself. Its been quite some time that I have hardspled it and have been using it. But recently I am facing this issue, so I am trying to move to original RUU and try if it works.
So for that anyone knows if we can remove hardspl from bootloader, because I am only able to enter bootloader. Moreover I tried several original roms from Flash Center as well as through SD card as well, but still be SPL version is 4.70.yang. Anyone knows any other alternative.
Also, if anyone has faced similar problem then kindly advice how you resolved.
Thanks in advance!
Regards,
Pankaj

I need some help BAD! My Tilt lost sound and black screen after boot

I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.

shawndh said:
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
Click to expand...
Click to collapse
Ick...this sounds like one of a couple of things...either you really screwed it up (btw, even "really screwed up" has been known to be fixable thanks to the super awesome folks here on XDA Devs) or it's a simple fix. My first suggestion would be to put it back into bootloader (just hold the usualy bootloader buttons and stick the stylus up in the Reset hole OR take the batter out and put it back in, your choice I think) and try rerunning everything EXCEPT the KasierUnlocker (btw, dont quote me but I would almost swear KaiserUnlocker needed a special radio flashed in order to properly work...you may wanna head back to that thread and check it out. I unlocked mine with it and I can about guarantee I had a special radio...) and see if it fixes anything OR find a compatible radio and reflash it (well, first off...get it into bootloader and tell us what the bootloader says on it)
Anyways, first things first would be to see what the bootloader is showing and then work from there. Sounds like a little bug so don't freak out too bad. If you think flashing these babies are hard then you really didnt try flashing G4 versions of the Wizard =P I totally bricked one because it was the pesky G4s and I didn't realize it at the time (complete newbness lol) So yeah, Kaiser's are a LOVELY change for me =] I've flashed mine countless times and loved it since the moment I got it! =D
But yeah, gimme info! =]

Did you use WM6.1 or WM6.0 to unlock the phone? Put in boot loader and flash orginal WM6.0 ROM as the other user suggested. You should be able to flash it if it is not a brick.

If it doesn't work you can use mtty to recover your phone, the needed information you'll find in the Kaiser Wiki.
Hope it helps

I just had this exact problem.
Use the EXE included in the tutorial to flash any windows 6.1 ROM from the bootloader via USB, and you will boot again.

HTCOmega said:
Ick...this sounds like one of a couple of things...either you really screwed it up (btw, even "really screwed up" has been known to be fixable thanks to the super awesome folks here on XDA Devs) or it's a simple fix. My first suggestion would be to put it back into bootloader (just hold the usualy bootloader buttons and stick the stylus up in the Reset hole OR take the batter out and put it back in, your choice I think) and try rerunning everything EXCEPT the KasierUnlocker (btw, dont quote me but I would almost swear KaiserUnlocker needed a special radio flashed in order to properly work...you may wanna head back to that thread and check it out. I unlocked mine with it and I can about guarantee I had a special radio...) and see if it fixes anything OR find a compatible radio and reflash it (well, first off...get it into bootloader and tell us what the bootloader says on it)
Anyways, first things first would be to see what the bootloader is showing and then work from there. Sounds like a little bug so don't freak out too bad. If you think flashing these babies are hard then you really didnt try flashing G4 versions of the Wizard =P I totally bricked one because it was the pesky G4s and I didn't realize it at the time (complete newbness lol) So yeah, Kaiser's are a LOVELY change for me =] I've flashed mine countless times and loved it since the moment I got it! =D
But yeah, gimme info! =]
Click to expand...
Click to collapse
I know. The crazy thing is that I've successfully flashed a G3 and a G4 Wizard and I still find this confusing.
When I go to the boot loader screen I have:
KAIS1*0
SPL-3.56.Hard
CPLD-8
When I reset the device normally I get:
R 1.27.12.11
G 22.45.88.07H
D 1.62.00.00
I didn't try to flash any other ROMS to unlock it. I just went with the hard SPL and then tried the Unlock tool. The phone is stock.

Thanx for the replys. I reflashed the original ROM and now it's working again. This is what I have now:
When I go to the boot loader screen I have:
KAIS1*0
SPL-3.56.Hard
CPLD-8
Now when I reset the device normally I get:
ROM version 1.62.502.0
Radio version 1.27.14.09
Protocal version is 22.45.88.07H
Device info:
Windows Mobil 6
CE OS 5.2.1622 (Build 18128.0.4.4)
Can I go strait to a SIM unlocker and then flash a new ROM?

Well you've got HardSPL 3.56 flashed to it.
Why do you need to sim unlock it? Sim unlocking is not neccesary to flash one of the many Roms avaliable for the Kaiser/Tilt.
Once it's got HardSPL flashed, you're free to flash any type of rom onto it

shawndh said:
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
Click to expand...
Click to collapse
A couple of things:
1) The Kaiser-Unlocker only works on 1.xx hardspl's, so you'll have to put one of those on first.
2) You do need to install the patched radio before you run it.
3) You'll need to flash a compatible radio afterward too, or else your device might not boot all the way.
4) Next time please post these questions in the thread for the unlocker you are using. It makes it much simpler for everyone.

stuff said:
Well you've got HardSPL 3.56 flashed to it.
Why do you need to sim unlock it? Sim unlocking is not neccesary to flash one of the many Roms avaliable for the Kaiser/Tilt.
Once it's got HardSPL flashed, you're free to flash any type of rom onto it
Click to expand...
Click to collapse
But HardSPL 3.56 doesn't SIM unlock the phone from what I understand. I need to use it with T-Mobile SIM. So I need to chenge to a 1.XX Hard SPL to do this?
So I guess I went wrong with flashing 3.56 first and not 1.1
Then I need to patch the radio
Run the unlocker
rinstall the radio
Then flash the ROM
Problem I have now is that I can't seem to go back down to a lower SPL version.

shawndh said:
But HardSPL 3.56 doesn't SIM unlock the phone from what I understand. I need to use it with T-Mobile SIM. So I need to chenge to a 1.XX Hard SPL to do this?
Click to expand...
Click to collapse
You need to read the instructions carefully, and ask questions in that thread. All the experts in unlocking will be there to help you.

Unbrick my Arrive

I have an HTC Arrive and I am hoping someone can help. I have an interesting brick I havn't read anywhere else about. Hoping someone can help me unbrick my phone.
First, how my phone became a brick.
I had DFT's 8107 Rom flashed and used RSPL to flash the DFT Tango rom but WIFI hotspot wasn't working so I decided to flash Ansars tango rom.
I used RSPL to try to flash it but it got to 85% and then gave a connection error. I beleive it was error 262. I followed the on screen directions that had me unplug my phone remove the battery and put the battery back in and reflash. When my phone restarted it went into boot loader mode but it showed SPL and the RUU gave an error again. I figured it was because it was no longer in RSPL. I put it intop RSPL and then into HSPL that time to prevent the error from happening again. I then reflashed the rom this time with no errors. But, after that when my phone restarted it showed the HTC screen and then the Windows Phone screen and then it freezes. It eventually resets itself and does the same thing again. I have tried flashhing multiple roms to try to fix this problem but nothing has worked. I even tried using zune to restore an old backup.
Does anybody have any ideas what could be wrong and what I could do to unbrick my phone. Please help.

did it show the correct spl when you entered boot loader mode? (is. 1.xx instead of 4.xx or 5.xx? You may need to run the spl downgrade again.

In bootloader mode I was able to put hspl on and it shows version 1.25. I ended buying another arrive on ebay. My bricked one had a cracked screen and hinge anyway. I'm still open to suggestions to resurrect it though because if I do then since I will have an extra I can keep one hacked and one stock.

like the one above said - the bootloader can be fault, like only displays the SPL/RSPL/HSPL but not function like it should. i would suggest you to do a gold card downgrade and flash a stock ROM for you HTC Arrive (or is it maybe a 7 pro gsm version?) and then again RSPL/HSPL, and then a custom ROM if you want.

Have you tried to just flash the OSPL 1.29 from the HSPL post, and then try the RSPL/HSPL again? No need to goldcard this phone if you are able to at least flash things.