I'm trying to put the android 2.0.1 on my touch pro and am having some troubles.
I am getting to where you run HaRET and it starts up and pulls up the loading bar that says it is going to run linux. It loads all the way up then the load box goes away and it leaves me frozen at the file explorer with the haret start bar on the bottom and also the file bar on the top.
I attached a picture showing my phone at this screen too.
Thanks guys
It just seems like linux will not start up for me? Is there something else I should do?
Read: forum.xda-developers. com/showthread.php?t=601751
and/or
forum.xda-developers. com/showthread.php?p=5420781#post5420781
Related
Ok let me set up the scenario for you all.... As you know I have previously cooked roms so this is very confusing for me...
First of all, I am using the newest ATT 214 ROM just recently released... I extract the .nbh file and start cooking.... I do my thing I always do and cook away...
I have completely stripped the OEMOperators Package and have my own...but it is following all the proper steps through the config.txt ect....
WHats happening is the ROM loads, go through the calibrating the screen, click skip a few times and the Green Windows screen loads. THe box for Customizing will begin in 3 seconds pops up and it starts.
After starting it changes my .tsk file and starts to run the NetCF3.5 cab file like instructed. It then quits. The screen that shows the progress disappears.. and it shows the homes screen. Problem is the phone is not usable at this point and I need to soft reset...
Once I soft reset it goes through the same thing over and over!
Any insight what is causing this would be most helpful????
I'm running JF's 1.5. I was able to get Debian to install successfully, although chmod didn't work for me I used
Code:
sh ./installer.sh
from my /sdcard, and it worked like a charm.
Anyway, here's what's happening to me. AndroidVNC will connect no problem, but all I get is a gray screen with a black X for a cursor. How would I remedy this?
Also, Debian forces my device to reboot randomly. When I hit the home key and go back to Android's home screen, there are times that the device will just restart. I hope it's not crashing.
Lastly, I used sdsplit to make an EXT2 partition on my sdcard. Do I need it for debian, or is FAT32 good enough?
I haven't gotten around to resizing my debian image because I'm too lazy to go get my ubuntu CD ... could it be that I don't have enough space in the image for iceWM, which is keeping me from getting a GUI in AndroidVNC?
Sorry about the newbie questions... I tried searching but I couldn't find anything helpful.
Yes.. I think the image size is the problem of getting gray screen
I had the same problem and I didnt both to resize the image either. I just assumed it was because I used that different technique. lol I have Ubuntu at home and will try that.
ParanoidAndroid said:
I'm running JF's 1.5. I was able to get Debian to install successfully, although chmod didn't work for me I used
Code:
sh ./installer.sh
from my /sdcard, and it worked like a charm.
Anyway, here's what's happening to me. AndroidVNC will connect no problem, but all I get is a gray screen with a black X for a cursor. How would I remedy this?
Also, Debian forces my device to reboot randomly. When I hit the home key and go back to Android's home screen, there are times that the device will just restart. I hope it's not crashing.
Lastly, I used sdsplit to make an EXT2 partition on my sdcard. Do I need it for debian, or is FAT32 good enough?
I haven't gotten around to resizing my debian image because I'm too lazy to go get my ubuntu CD ... could it be that I don't have enough space in the image for iceWM, which is keeping me from getting a GUI in AndroidVNC?
Sorry about the newbie questions... I tried searching but I couldn't find anything helpful.
Click to expand...
Click to collapse
yeah my G1 also reboots randomly with debian :/ usually after a short while, but it happened before i put ext2 on SD and it happens after I split SD
no idea what can causing it...
ParanoidAndroid said:
Anyway, here's what's happening to me. AndroidVNC will connect no problem, but all I get is a gray screen with a black X for a cursor. How would I remedy this?
Click to expand...
Click to collapse
As you describe it, it looks to me as if you haven't edited /root/.vnc/xstartup for adding the window manager and/or you haven't installed the window manager, or there is a typo at /root/.vnc/xstartup.
That grey screen with the "X" cursor is the pure X server, without the window manager decorations.
Hello, I have a XDA Orbit 2 (screen res 240x320). I wanted to install Android on it. I did a quick search and found a few things....
My Tutorial:
http://forum.xda-developers.com/showthread.php?t=625200
I had a read though that. Got a rough idea on what I was doing.
(1º CHOOSE YOUR ANDROID BUILD) I decided to use:
Warm Donut (Donut): http://forum.xda-developers.com/showthread.php?t=619980
(2º INSTALL THE OS LOADER TO NAND) Now this was my problem, I visited the website "http://it029000.massey.ac.nz/vogue/files/?C=M;O=D" to choose my .NBH file. I choose the latest ones. And the selection was:
polaimg-panel1-320-08-04-10.nbh
polaimg-panel2-320-08-04-10.nbh
polaimg-panel3-320-08-04-10.nbh
I tested ALL 3 and non worked (unless I was doing something wrong) all i got was when it restarted it went to a fizzy kind of screen then came straight to a white one.
But I did try another .NBH file what was near the bottom called "polaimg-240x320-03-02-10.nbh " that didn't work but it was close.... when it restarted it vibrated once then went to a black screen then vibrated twice then came to another screen with a animal in the top left and under niethe they was loads of white numbers letters scrolling down the screen then it just got stuck on that and nothing happened from there.
EDIT:
I have got a bit closer now. I decided to try run it through haret, Well... I click Run. see black screen with letters scrolling, I get to the bit where it says "Hold down Volume Up or DPad center to launch installer. And before I have chance to do that this appears under:
Code:
sh:2: unknown operand
losetup: /dev/block/loop 1: No such file or directory
Failed
Failed to reach system.img on SD card.
Can anyone help me? or point me in the right direction to get android installed on my xda orbit 2?
Thanks, James
Just try a earlier nbh i use polaimg-panel3-320-29-03-10.nbh most of the later ones have either problems with sound or wifi.
If you get a white screen it's prob wrong panel depends on you phone pola100 or 200.
Thanks, But I have tried that.
I have a new problem now. Might be easier to solve.
can't anyone help? kinda in a rush for it.
Hi,
i had the same problem with another build.
You should try to get into the installation menu and install Android.
This helped for me.
I found the solution here on xda-developer.
Since I am too new or too stupid to post a link the post seems to be this one:
showpost.php?p=5602064
Have fun,
René
Hi there!
Not sure if this is the right section to post this...but here goes.
I've got an apk I need to install stored on my external SD card. When I press to install it the display dims and just hqngs there until I press the screen to undim it.
How is this fixed?
Thanks.
When the screen dims and just hangs it usually means that there is a choice of apps to open the file/ execute the command, but in HC there is a bug that sometimes stops the dialog box from being displayed. You just need to rotate the Xoom with auto rotate enabled and the box will pop up.
Thanks for the reply Okantomi.
I pressed the apk until the dialogue box appears which gives me the choice of how to deal with the apk file, i pressed install. it then just hangs on the dimmed screen.
I will give your advice a go, and see what happens.
Thanks again.
People, I've tried a bunch of assemblies and options for your phone after the display is changed to the Chinese and found that only 3 boot penguin display and inscriptions at boot true test, with those two idit load equally, and one with the other inscriptions but also hangs. These feeders: 1) polaimg-panel3-240x320-2.6.32-froyo-06-09-10_22 2) polaimg-panel3-240x320-2.6.32-froyo-09-09-10_21 3) polaimg-panel3- 240x320-2.6.32-froyo-27-08-10_23.
All three normally pick up the screen but the writing bug usb_vsync.
Founded on the Internet has the very first assembly androyda, who works in the demo rezhime.Reshil try to install it and wonder, android has started without any problems.
Here is a link to the installation package that will install this demo on your phone: hxtps://rapidshare.com/#!download|304l34|123389441|RUU_Polaris_Android_DEMO_v1_0.exe|72394|R~EC5F7C5EBDDD628BF8BFF91F71607033|0|0
Those who say they say android does not support Chinese screens, just a lie or do not know. At this assembly it is clear that androyd runs perfectly, and on the phones with a Chinese screen.
Most likely, DZO, or what the other developer of the kernel is not corrected. Suggest to write a petition to save money and to develop a normal boot. Let's say it can do the same DZO or what the other developer. I do not think it would be very difficult and time consuming. Who can help me in this, please come forward!
But there's more, I decided to try to run through the HARET andriod 1.5 on the same firmware WM and you think, android has started well!!
At the moment, try to build a working version of Ecler, I do not know whether I can or not but the fact that at least 1.5 works already happy!
That it happened. All the same I managed to run Android on my devayse 2.1-2.2. Of course there are problemma, and a large - is not responsible for nozhatie touch screen, but the fact that he obsalyutno normally displays everything on the screen is great plshyusom and proves once again that all the matter in the loader, which local craftsmen or they can not fix! !
Below we will explain how to start. If you do not get something right the first time, try again, I got yed)
1) Download the assembly android_by_polyrhythmic-beta3.zip (Look on the internet, I think problemma not be found)
2) Download the assembly polymod.rar.
3) Unpack android_by_polyrhythmic-beta3.zip and copy the folder on the SD android.
In the folder are 2 files android default and default-s, files and zImage-15-12-09 and zImage3. The file default by one run android in Haret changing the panel on 1,2,3. Each time you start when you have to wait for the LED zamegaet either blue, green or yellow, and goes off the screen. This would mean that the android booted and shut off the screen. After clicking on a retreat or off you will see a white screen.
After running all three panels so turn off your phone zaydmite to stick and move to folder android Fail of the default-polaris zborki polymod and change it to default. Replace the old Fail them, and then rename the zImage-15-12-09 in just a zImage. Now run the android. Wait until you have a light starts blinking LED goes off and the screen. As it happens, click on the rebound a few times. You will see a line of code and then the welcome screen android. Since the touch screen is not working I could not go further, but pressing the buttons can be issued to the soglashatsya message.
Here vprintsype all.
Try it. The point I was told, then I welcome your ideas and results!