Members I need some help to crack the case open of my phone, i manage to get the back cover off, but the front face and printboard seemed to be glued together somehow...and i have no idea how to detach the slider spring mechanism of the phone. Anyone more pointers?
thnx
Related
Hi guys
Can any1 provide me with a picture, or video so I know which screw I should remove for quitting the usb charger rubber cover ?
I know I must quit its battery, but can't find anything near the cover that can help me to quit this disturbing thing
Thanks a lot in advance...
You don't need to remove anything except the battery cover. You will need a screwdriver or some metal object to remove the cover. The rubber thingy is friction fit, you can always put back. Just yank it out like a crowbar.These things are tough so don't worry about breaking it.
Hi,
I wonder if someone can offer any suggestions... The end of my stylus has broken off and left the metal part right inside the phone. I've tried with jewellers screwdrivers and tweezers to get it out, to no avail.
Any suggestions?
Have a look at the Polaris Wiki and get the service manual to disassemble the case.
Happened to me yesterday .Get a needle,press point of needle againt stylus.then push it out.took me 2seconds.
If the needle trick doesn;t work I somehow used a needle to prize the chamber open via the side and then freed the stylus by sliding it down. It hasn't damaged my polaris in any way. Sorry can;t be more specific but it wasa while ago!
Another way would be to take a bit of wire or a cocktail stick, apply a small drop of super glue to the end and press it onto the broken end of the stylus (being careful not to touch the sides of the polaris)
Then wait a few seconds for it to dry and pull it out!
Dear Nordberg !
try to put some glow on the top of the rest of ur stylus and put it back in ur PPC, let it a few minutes then try to pull it slowly and u will have a one piece stylus ......
The magnet holding the stylus seems to have either come off its usual spot or is turned in another direction. But the stylus wasn't holding anymore. Today, I got to work and noticed I had lost the stylus. Is there any known fix for this? I never dropped the phone, it just wouldn't work one day.
Thanks for any help.
Did you open the Stylus? You can srew it (upper black part) up, where you can see the magnet that is hold by a plastic part: it cant move .... did someone fool you?
Greetz
Boris
Well, my stylus is lost now so it's too late. No, nobody was trying to trick me. Are you saying that the only magnet is in the tip of the stylus? The end that you write with? Because I believe I have another one.
with mine you cant write like a pencil only on the touch screen without ink ;-), its a touch pro without branding original from HTC. the magnet in it is placed in the inner stylus ca. 3 cm upwards from the "tip" ..., you can say just in the middle ..
Greetz
Boris
Well, mystylus was going into it's sleeve and not staying in, it was just sliding out. So, I don't know where the magnet was at all.
For me it seems that the contra part in the inner of your device (ferrum or magnetic) has moved or is broken so the magnetic stylus "found nothing to be magnetic with" hope you understand me, my english is worst .... You know that you need a little Power to remove the stylus from his hole. if you could test it with the other stylus that you still own (but must be for the TP!!), wether the stylus is hold or not.... and have a look in the inner of the stylus wether the magnet is there...
good night.... perhaps till tomorrow.... If you need a plan from the inner parts of the TP: i have one
Greetz
Boris
P.S. If you shake your device: Do you hear anything ??
Well, I tried but my replacement stylus didn't work. There is definitely a magnet missing inside the phone. At first it was tight, then it seemed blocked and now it just glides in and out.
So, can anyone give me any hints about what I can do to fix my stylus not sticking in its sleeve? I really need this fixed. Is it safe to open up a Fuze?
This happened to me today...
i have removed the battery, chip, microsd and then the back cover... a bit tricky but it was easy (folowing the dis/assembly guide), for mine the lower part didnt want to go out, so i pull out the speaker connector and then push it out.
and the other magnet was there... and it have a place in the back cover that i think it may be seen if you take the battery out... it have like a dent
now my problem is with the polarity... i dont know how to glue it ... it have 2 positions vertical or horizontal
the vertical position will attract the stylus but it seems not to enter completely
the horizontal will push it, but i dont know if it will hold it as is very hard to test it without adding glue and i will use exposy...
EDIT1: found where it go... its in the vertical position but it need to be tested (because the polarity is different dont know why) if you are going to glue it
EDIT2: i used a plastic card (old medic card, visa, ect) to pry out the back cover from the keyboard
Thanks
Many,many thanks to you.
Same situation so easy but the lose magnet not easy to find except by your tips. Ha, ha I love this forum, So many thanks to the people here who contribute helping each other
jorgepr13 said:
This happened to me today...
i have removed the battery, chip, microsd and then the back cover... a bit tricky but it was easy (folowing the dis/assembly guide), for mine the lower part didnt want to go out, so i pull out the speaker connector and then push it out.
and the other magnet was there... and it have a place in the back cover that i think it may be seen if you take the battery out... it have like a dent
now my problem is with the polarity... i dont know how to glue it ... it have 2 positions vertical or horizontal
the vertical position will attract the stylus but it seems not to enter completely
the horizontal will push it, but i dont know if it will hold it as is very hard to test it without adding glue and i will use exposy...
EDIT: found where it go... its in the vertical position but it need to be tested (because the polarity is different dont know why) if you are going to glue it
Click to expand...
Click to collapse
Hi, I just have a problem with my 5 day old sw2, I overstimate the waterprooftness of the device and take it to the pool, everithing was fine but in home I can see a weird spot on the screen in the button side, was small next day the spot get bigger and the retroilumination was gone, I turn the watch off and let it dry for a few days, the spot still remains I turn it on and the retroilumination is back, but I want to clean the screen and clean all the board from water before it can get more damage. The big question, anyone have attempt to open the watch? cant find any guide, dont know if start for the screen with a heat gun or in the back with some sputgers, the watch is still turn off. Please if you have any suggest let me know thanks.
If not will post the first tear down guide hope with success, or it will be a destroy guide.
Ok I did it, heres how to do it:
First apply some head gun in the sides of the watch, be careful dont use too much heat.
Press from the back of the device gently, your will see that is one solid block inside a frame that hold the strap.
To separate the screen to see the board and battery, apply head gun DONT USE TOO MUCH HEAT, (if you do that the adhesive form the digitizer will melt and can leave a really ugly spot) after that with a plastic spudger work around the frame gently. Behind the screen is a flex cable be careful separate it for board to fully lift the screen from the boddy of the watch.
The battery connectors are soldered to the board and have very thin connectors be careful.
I cant remove the board mostly for the NFC chip that was glued in the botton of the device.
The screen is fused so YOU CANT replace just the digitizer or just the LCD.
I cant find any repacement part of the LCD, I thing I have a really nice strap with a circuit board If you have a not working watch and the screen is OK please PM I want to purchse a part, thanks
Hey I'd appreciate an update on this. I may have a watch with a good screen. Tell me if you open the watch is there a way to make it waterproof again? did you find any water inside?
So there is this thin plastic-ish strip on top of the button ic but under the physical button, just open your back cover and you'll have an idea of what i am talking about, it has this black center and is goldenish color the rest.
So, I was opening the cover and that 'thing' from the power button and volume + button fell off, I didnt pay much attention, but now those 2 buttons wont work on there own, still I can get them to work by opening the cover and using something pointed, so as far as the IC or the chip or whatever it is, is still fine.
I need some suggestions on some makeshift ideas on how to fix it so the buttons will work with the cover on. Also if possible, anybody know if the mobile guys fix it and how much it costs? Dont worry about where you live, I just want to have a rough idea I dont like walking in to a mobile mall and feeling all dumb
Thanks in advance, and the other thanks you'll all receive anyway for helping
Fas1h said:
So there is this thin plastic-ish strip on top of the button ic but under the physical button, just open your back cover and you'll have an idea of what i am talking about, it has this black center and is goldenish color the rest.
So, I was opening the cover and that 'thing' from the power button and volume + button fell off, I didnt pay much attention, but now those 2 buttons wont work on there own, still I can get them to work by opening the cover and using something pointed, so as far as the IC or the chip or whatever it is, is still fine.
I need some suggestions on some makeshift ideas on how to fix it so the buttons will work with the cover on. Also if possible, anybody know if the mobile guys fix it and how much it costs? Dont worry about where you live, I just want to have a rough idea I dont like walking in to a mobile mall and feeling all dumb
Thanks in advance, and the other thanks you'll all receive anyway for helping
Click to expand...
Click to collapse
Well, you can easily fix it yourself if you are a bit smart. Just try to stick a box shaped paper tape at that place where the plastic broke off from.
Cut tape in a small rectangle. Then cut that rectangle into many small pieces of same size and form a small rectangle. Then stick them to the place where "that thing" came off.
You can also use a double end sticky tape but usually the thickness is defined so I am not sure if that will help.
HTC Sensation is an old phone however, you should easily find old bodies/ new cases to replace your current body.
Good Luck
Thanks my explorer had a similar problem Its original back cover's buttons worn off, so I folded up a piece of paper and stuck it there and used a cover over the worn out back case. With sensation there is no way to make the paper stay in the same place, i didnt think of paper tape or double sided tape, will give it a shot.