Related
Greetings... It's been only two days since I've bought my HTC Tornado (T-Mobile SDA). After unlocking it, I tried uploading different ROMs (i-mate SP5m, Cingular 2125, etc), just to find the one that suits me. Anyway, I found this T-Mobile SDA II ROM and without a second thought, I uploaded it to my phone. I didn't realize than this ROM was for the HTC Hurricane. After the "successful" upload, the phone went off! Now it does not boot at all, the battery does not seem to charge, I'm not even able to launch the three-colour bootloader screen (camera button + usb plug).
Can I upload a new ROM? Is there a way to recover my phone?
If the flashing stated it was successful then it should be. Try other fully charged battery.
Thank you for your quick answer. The battery was fully charged when I flashed the phone. Unfortunately, I found out that the "bad" ROM that I uploaded was for the HTC Hurricane phone!!! Is there anything I can do right now? Is it recoverable?
you *might* be able to recover with a SD card image, not sure
just connect your phone to the computer, turn it on, and immediately run a PROPER rom update for it, you might be able to get it back.
i did the same with a tornado rom on a SP3i (typhoon) and managed to get it back after a few tries
good luck
The problem is that I cannot turn my phone on. The phone seems completly dead. Just like having no battery installed (which btw is fully charged). I can't get to the bootloader (RGB) screen. Is it possible to use a SD card image? If I won't be able to update the rom, do you know if the HTC support can do it or should I throw my phone away?
dead is dead!
if the phone is under warranty , it should be no problem to get new one!
I didn't know that Hurricane can stop a Tornado ..well maybe it was just the end, and yes, if it still has warranty, use it.
Please observe Silence for 2 mins.
NiTroGenious said:
Thank you for your quick answer. The battery was fully charged when I flashed the phone. Unfortunately, I found out that the "bad" ROM that I uploaded was for the HTC Hurricane phone!!! Is there anything I can do right now? Is it recoverable?
Click to expand...
Click to collapse
i got the same problem, still don't know how to recover from this problem, if u found some result, plz post an i'll post also what i found
NiTroGenious said:
Greetings... It's been only two days since I've bought my HTC Tornado (T-Mobile SDA). After unlocking it, I tried uploading different ROMs (i-mate SP5m, Cingular 2125, etc), just to find the one that suits me. Anyway, I found this T-Mobile SDA II ROM and without a second thought, I uploaded it to my phone. I didn't realize than this ROM was for the HTC Hurricane. After the "successful" upload, the phone went off! Now it does not boot at all, the battery does not seem to charge, I'm not even able to launch the three-colour bootloader screen (camera button + usb plug).
Can I upload a new ROM? Is there a way to recover my phone?
Click to expand...
Click to collapse
i got the exactly same problem still don't know how to recover, if found plz help and post
this is exactly why i get the jitters everytime i flash my phone... i'd rather do a hard reset. i'll only flash ONLY if it comes to it, when it comes to it; and if there's a new rom worth it (like the wm6 rom the geniuses are making here... can't wait 'til the 'alpha' comes out ^_^)
ludatrick said:
i got the exactly same problem still don't know how to recover, if found plz help and post
Click to expand...
Click to collapse
Well, there is no recovery!!! Just sale your dead device for spare parts, as I did!
NiTroGenious said:
Well, there is no recovery!!! Just sale your dead device for spare parts, as I did!
Click to expand...
Click to collapse
don't take it as a joke, and if i send to HTC?
Who's joking?
If that is the case, you might need to change the corrupted ROM chip, and usually they will change the whole mainboard, which is very expensive, not worth to repair
They asked about 600€ for the repaid, so I bought a new one (380€) and sold the broken one for spare parts.
600 EUROS for repair ? In my country, that is 4200 bucks, enough to buy a brand new O2 XDA FLAME.
A new one for 380 EURO ? You can get HTC Hermes with that amount in my country,
The repair cost in my country will definitely be lower than 100€, why not send it to me via courier, and see how much would HTC repair it here
yeah, sell it for parts and save up for the htc advantage ^_^
~NiTroGenious
Look this: http://www.smartphone-developers.com/
I have spv, but processor is OMAP710. Is for somebody spv (Canary or Tanager) his phone with OMAP5910 processor???
I read here: http://wiki.modaco.com/index.php/HTC_Tanager
OMAP5910 datasheet: http://focus.ti.com/lit/ds/symlink/omap5910.pdf
Tornado have a 10 pin jtag connector!!!
You can find it possibly the jtag points with this software, http://www.c3a.de/wiki/index.php/JTAG_Finder
and with this hardware: http://www.xilinx.com/support/programr/jtag_cable.pdf
You must find TRST, TDI, TCK, and TRST must pull up VDD with ~200R resistor.
Good luck!
Great info, Dibi. Thanks!!! Although I have sold my "brick" for parts, many unlucky guys will find this information useful to revive their phones.
Hey guys I like this community and would love to get more involved. I was wondering if some of you could help me understand some of the lingo around here so I can get better acquainted with what I am doing. I would like to load a cooked rom onto my HTC Touch I have the sprint version, but I went to the touch section on the forum and it feels like I am trying to read another language >.< so if anyone could help me understand some of this I would be greatly thankful, thanks in advanced
cooked roms are custom roms. your provider locks your device to only ve able to load roms that they provide... therefore you need to unlock your phone to be able to flash it (through hard spl.)
here is a link on flashing your first rom.
Just follow directions and you will be fine (BUT MAKE SURE YOU FOLLOW THEM OR YOU WILL TURN YOUR PPC INTO A VERY EXPENSIVE PAPER WEIGHT)
Wow thank you tons for the quickness of the reply
no prob
Everything went fine when I was going through the steps, and everything seemed to be going right through the HardSPL step three, but when my phone restarted itself, I got nothing but a backlight I hope I dont have an expensive paper weight >.< Is there anything I can do to fix it?
what phone are you using
Im using the HTC Touch by sprint, but now instead of black it is The HTC smart Mobility screen
The thread i gave you earllier was for a refrence on how to flash....
I'm guessing you tried to install something from that page. (that page was for the kaiser)
You can only flash things made for your device.
Here is a such thread with some refrences to the correct things you will need
http://forum.xda-developers.com/showthread.php?t=458449
PS: if you think you bricked your device here is some info on unbricking
http://forum.ppcgeeks.com/showthread.php?t=24906
Yeah no it's completely bricked now I cant even get it to turn on :/
If you can get to the bootloader on your device by following the instructions here you can save your device:
http://forum.xda-developers.com/showthread.php?t=362768
"hold the end key and the side camera key and stick the stylus into the hole"
you will need to hold the buttons till after the screen comes up (if you can get it to come up)
Yeah I cant even get my phone to turn on now Im guessing its done for good :/
i got an atom exec its actually not mine its my little brothers atom exec. His hardware button seems not to be functioning etc; Phone Button, Start & Message Button. Can anyone teach me how to remap the keys or anything that i need to install to get it work. thanks
ashburn said:
i got an atom exec its actually not mine its my little brothers atom exec. His hardware button seems not to be functioning etc; Phone Button, Start & Message Button. Can anyone teach me how to remap the keys or anything that i need to install to get it work. thanks
Click to expand...
Click to collapse
Before remapping, always try (if you haven't already done so) to go through a soft reset. Sometimes, they keys get "locked" because some program in WM is not responding...
BTW, which OS are you running?
i tried soft resetting still nothing happen its running on Windows Mobile 5. i could not Upgrade it to 6.1 because my lil bro killed the bootloader
try a hardreset n c what happens....or get some soft key manager n try with it...
Hbutton actually works pretty good. I used it a few times and it does a good job for the remapping. If you feel confident enough with the Registry, you can also do it that way.
egzthunder1 said:
Hbutton actually works pretty good. I used it a few times and it does a good job for the remapping. If you feel confident enough with the Registry, you can also do it that way.
Click to expand...
Click to collapse
okay im confident with Registry... as the guy above ur post said to hardreset well i cant hardreset cause i need the Call bottons. so what should i do in the registry??
kpshamilsagar said:
try a hardreset n c what happens....or get some soft key manager n try with it...
Click to expand...
Click to collapse
i cant hard reset without the DPad Working
ashburn said:
okay im confident with Registry... as the guy above ur post said to hardreset well i cant hardreset cause i need the Call bottons. so what should i do in the registry??
Click to expand...
Click to collapse
Can you flash with an original shipped rom? (you know, the RUU from the manufacturer) That normally requires no interaction with the device since the software automatically puts the device into bootloader. I will try to find the Registry keys. There was a good post with all that information a while back... I'll see if I can find it.
egzthunder1 said:
Can you flash with an original shipped rom? (you know, the RUU from the manufacturer) That normally requires no interaction with the device since the software automatically puts the device into bootloader. I will try to find the Registry keys. There was a good post with all that information a while back... I'll see if I can find it.
Click to expand...
Click to collapse
thank you very much. but i cant flash my lil bro apparently somehow killed the bootloader... only way to have bootloader back is to do it manually by opening the device but i wont want to do that lol his phone might just get worst..
ashburn said:
thank you very much. but i cant flash my lil bro apparently somehow killed the bootloader... only way to have bootloader back is to do it manually by opening the device but i wont want to do that lol his phone might just get worst..
Click to expand...
Click to collapse
I guess I should read a little more carefully since you mentioned this in an earlier post.
Look at this that I stumbled upon while browsing the Atom forums. Look at posts 214 thru 216. There is an app that is called resetbootloader.exe.... I guess this might be what you need.
http://forum.xda-developers.com/showthread.php?t=455827&highlight=bootloader&page=22
Let me know how it turns out...
egzthunder1 said:
I guess I should read a little more carefully since you mentioned this in an earlier post.
Look at this that I stumbled upon while browsing the Atom forums. Look at posts 214 thru 216. There is an app that is called resetbootloader.exe.... I guess this might be what you need.
http://forum.xda-developers.com/showthread.php?t=455827&highlight=bootloader&page=22
Let me know how it turns out...
Click to expand...
Click to collapse
nope its not working..... the bootloader on my lil bro atom is dead.... i cant get to bootloader.. maybe the best is the Registry thingy or is there any other way to remap hardreset botton instead of using the call & end call botton?
ashburn said:
nope its not working..... the bootloader on my lil bro atom is dead.... i cant get to bootloader.. maybe the best is the Registry thingy or is there any other way to remap hardreset botton instead of using the call & end call botton?
Click to expand...
Click to collapse
See if you can downgrade the bootloader by following this thread
http://forum.xda-developers.com/showthread.php?t=358704&highlight=downgrade+bootloader
First you [highlight]must[/highlight] make sure that this is for your phone. If it doesn't work, try to find a program called HButton (it can be found in the Dev and Hacking section), this will do the same thing as the Registry edits, but with a nice UI
Sorry but this is the limit of my knowledge... in theory, replacing the bootloader might fix what your little brother did, but then again, I am not certain since I do not own the device. Also, you may want to consider that the hardware buttons can be busted as well. Just a thought.
Good luck!
thanks again hehe it gave me alot of home lol but could not get it working. Maybe someone could give more solution on how to activate the DPads back lol hehe. The Problem Started when my Lil bro installed Touch Shell 3.0 thats what he said to me this morning... lol maybe some software aren't that friendly at all
those anyone know any apps that can do hardreset without using stylus & Dpad...??
ashburn said:
thanks again hehe it gave me alot of home lol but could not get it working. Maybe someone could give more solution on how to activate the DPads back lol hehe. The Problem Started when my Lil bro installed Touch Shell 3.0 thats what he said to me this morning... lol maybe some software aren't that friendly at all
Click to expand...
Click to collapse
I have used Touch Shell 3 (in a Blue Angel) and it shouldn't do anything like that (especially not busting your bootloader)... I have a feeling that your little brother is not telling you something or that his story is only half of what happened
As far as the "no stylus"... why not? I can understand that your DPad might not be working, but why not the stylus? If you lost it and need to reach the "Reset" button, just do what I do... use a paperclip (I have lost about 5 styluses and on the last one I said "screw it" )
One last suggestion, you could try to remove both battery and back up battery to clean the memory... I guess that would probably act as a hard reset for the device.
egzthunder1 said:
I have used Touch Shell 3 (in a Blue Angel) and it shouldn't do anything like that (especially not busting your bootloader)... I have a feeling that your little brother is not telling you something or that his story is only half of what happened
As far as the "no stylus"... why not? I can understand that your DPad might not be working, but why not the stylus? If you lost it and need to reach the "Reset" button, just do what I do... use a paperclip (I have lost about 5 styluses and on the last one I said "screw it" )
One last suggestion, you could try to remove both battery and back up battery to clean the memory... I guess that would probably act as a hard reset for the device.
Click to expand...
Click to collapse
hmmm good idea lol i did try reset using stylus but it resets but only thingy is the dpad..... hhehe removing battery is good but how do i remove backup battery??? can help me with it? lol kinda noobie.... he told me when i tried flashing..... it does not show bootloader but shows diagnose test i tried it myself it did not work and i looked upon this forum i need to dismental certain parts of the PDA
Dear Folks at XDA,
I would like to ask for you help with my HTC Touch Pro 2. I recently tried to update it to the new AthineOS CHome TF3D WM6.5 Manila ROM v 1.0 and unfortunately I failed.
The problem is that my phone now freezes at the black startup screen with the Touch Pro 2 logo and the red codes at the bottom.
I've flashed the ROM several times before and never got this issue.
Due to the fact that the phone doesn't finish the boot-up and I thus I can't get ActiveSync I'm afraid I messed up my phone for ever.
Please someone tell me I got a way out of this, I'd appreciate it very much.
Greetz,
SjonSjon
umm.... I don't think you can change the firmware just yet on the CDMA version of the phone... if you used a HardSPL that's available in the Rhodium forums then you probably used a GSM specific ROM on your CDMA phone... not sure what to tell you other than making sure you read the CDMA forum before trying something so risky. Best solution, unless someone knows how fix your phone in it's current state, is to toss it under your car and run it over and try to cash in on the insurance.
Problem solved!
Hey guys,
I got my HTC Touch Pro 2 functioning again. Thought I'd post the solution for other people who might encounter the same issue. I don't exactly know what the problem was. I'm assuming a non-compatible ROM or something, but after opening 30 tabs in my browser and reading my eyes out I found that if you put your phone into bootloader mode and connect it through usb to your computer you can flash the ROM without using activesync.
So I turned my phone off, pressed the power and Volume Down button simultaneously and then used the Stock ROM upgrade software from HTC to restore my phone
This solution beats the hell outta "run it over and try to cash in on the insurance" if I say so myself!
Greetz,
SjonSjon
I am glad you have recovered the beautiful device; and thanks for sharing a working solution.
sjonsjon said:
Hey guys,
I got my HTC Touch Pro 2 functioning again. Thought I'd post the solution for other people who might encounter the same issue. I don't exactly know what the problem was. I'm assuming a non-compatible ROM or something, but after opening 30 tabs in my browser and reading my eyes out I found that if you put your phone into bootloader mode and connect it through usb to your computer you can flash the ROM without using activesync.
So I turned my phone off, pressed the power and Volume Down button simultaneously and then used the Stock ROM upgrade software from HTC to restore my phone
This solution beats the hell outta "run it over and try to cash in on the insurance" if I say so myself!
Greetz,
SjonSjon
Click to expand...
Click to collapse
Good job!
big thanks for solution.
You just saved my life!!!
Don't get our hopes up! This is the wrong forum. CDMA TP2s can't be flashed at all yet.
This was a life saver post so a quick bump for anyone that needs it.
I unlocked my CDMA phone, installed a few roms -- decided to go back to my stock rom default (which was Telus) -- reinstalled and bam -- bricked.
Well, technically it's not a brick if you can get back into the bootloader to reflash. So no worries everyone. If everyone reads instructions well enough we should hopefully see zero "real" bricks. Or at most, just enough to only build bbq pit rather than a house.
I think my phone is truly bricked
I was unlocking my phone (the HTC Touch Pro 2 <Verizon>) and I was using a Diamond unlocker (I thought it would be fine), but during the process there was a connection error and now my phone seems to be bricked. I can't get it to even turn on, get to a bootloader screen, or anything even remotely close.
The one odd thing that it does though, is when I connect it to my computer, it pops up and my computer recognizes there is a device there. In my Device Manager there is an unknown device called: Qualcomm CDMA Technologies MSM. I have tried every combination of two buttons, including holding down the reset button with all of them, but nothing gets me anywhere.
If anyone could help, I would really appreciate it. Let me know if you need any more information.
my cdma is rebooting endlessley i reflashed stock rom and evorything. it seriously dosnt want to work. its most sadness... i am cashing in on the insurence. but they are going to send me a refurb..
spend 600$ on a phone got inurnce i hope the used one dosnt fail me.
Esazi said:
I was unlocking my phone (the HTC Touch Pro 2 <Verizon>) and I was using a Diamond unlocker (I thought it would be fine), but during the process there was a connection error and now my phone seems to be bricked. I can't get it to even turn on, get to a bootloader screen, or anything even remotely close.
The one odd thing that it does though, is when I connect it to my computer, it pops up and my computer recognizes there is a device there. In my Device Manager there is an unknown device called: Qualcomm CDMA Technologies MSM. I have tried every combination of two buttons, including holding down the reset button with all of them, but nothing gets me anywhere.
If anyone could help, I would really appreciate it. Let me know if you need any more information.
Click to expand...
Click to collapse
I did the same exact thing to mt TP2. Same outcome.
We have to learn somehow....
That stinks man. If you did, then your phone is truly bricked. You are going to have to get a replacement or switch to another phone because there is nothing you can do to get it going again. I tried everything possible and eventually just ordered a replacement. I have it now and it's working beautifully, but needless to say I am a little scared away from any more unlocking or flashing for a while.
If you read carefully you dont have to be scared of flashing
I was a noob some time ago but before doing anything I took care of reading and understanding before doing nothing.
lesson learned
By now I have flashed more than 60 times on 3 diferent HTC devices and all were a succes
Hope you get your TP2 working again!
I hope I can get there
Someday I hope to be a flashing expert, but until then I will take it slow and read carefully. Thanks for your encouragement. When I actually get money to pay for the unlock for my TP2, I will let you know how flashing goes.
How do you keep the phone in bootloader? Mine goes right to the press volume instuction screen. Other than that I'm stuck on the black name screen,also my usb will not register in device manager. This was my first try at flashing.
gadgetgirl28 said:
You just saved my life!!!
Click to expand...
Click to collapse
Holy hell, you're not lying. Thanks for coming back to post your solution!
This post saved me at least a few hours of frustration and ever worsening decision making.
So it's totally true???
this situation hasn't solution;
I was unlocking my phone (the HTC Touch Pro 2 <SPRINT>) and I was using a Diamond unlocker (I thought it would be fine), but during the process there was a connection error and now my phone seems to be bricked. I can't get it to even turn on, get to a bootloader screen, or anything even remotely close.
The one odd thing that it does though, is when I connect it to my computer, it pops up and my computer recognizes there is a device there. In my Device Manager there is an unknown device called: Qualcomm CDMA Technologies MSM. I have tried every combination of two buttons, including holding down the reset button with all of them, but nothing gets me anywhere.
If anyone could help, AND PLEASE somebody tell me , that it can be save it
;9
please help
i have the same problem. is there a way to save my phone?
I think i bricked theHTC fuze that i bought yesterday I tried to do the Hard SPL but i was getting an error message, error 244 invalid model ID so i used a program to change the .nbh (a radio file) file so it bypassed the error message (by changing DIAM***** to RAPH*****, since my phone is raphael). I even got a message that the process was successfully finished but it turned out not to be true because the screen went black and now i cant turn it on, and i cant even get it into the bootloader mode. If i could at least get it into to tricolor screen i would be able to flash back the original radio and that would solve the problem because ive already done it a few times. Please let me know if there is a chance to get it fixed, even i had to send it to a professional but as long as it could be fixed, im really desperate. Thank you
brick, htc fuze, diamond, raphael, hardspl
You only get that error when your trying to flash the wrong device... Did you use the file "Raphael_CDMA_HSPL_037.zip" to unlock..?? Sound's to me like you used the Diamond Unlocker... Shouldn't be that hard to fix, hold the volume down button, power button, and insert stylus into the hole on the bottom to soft reset to try and open up BL screen... LMK if that works...
Why didn't you just follow the instructions for flashing? You aren't even security unlocked, so why were you trying to flash a diamond radio? That makes no sense at all. Also, if you are security unlocked, you need to get diamond radios from the raphael forum, because they're patched to flash onto raphaels. It sounds like you got yours from the diamond forum, which is the wrong way to go (especially if it's a cdma radio-that would kill your phone for sure). Did hard spl work? If not, why on earth did you forge ahead? YOU CAN'T DO ANYTHING UNTIL YOU FLASH HARD SPL!!!!!
Try pulling the battery for a while, the see if it will start up. It's hard to tell what you did, but since you went down such a wrong path, I wouldn't be surprised if the phone is a giant brick.
komar808 said:
by changing DIAM***** to RAPH*****
Click to expand...
Click to collapse
this should've been clue #1. If you have to change it because of the device ID, it's the wrong thing to flash. The Diamond and Raph look alike on the front, but are almost totally incompatible ROM-wise.,
I even got a message that the process was successfully finished but it turned out not to be true because the screen went black and now i cant turn it on
Click to expand...
Click to collapse
You are wrong there, it did flash successfully. The tools worked EXACTLY as they were designed. It's not the tools fault
Please let me know if there is a chance to get it fixed, even i had to send it to a professional but as long as it could be fixed, im really desperate. Thank you
Click to expand...
Click to collapse
You might contact olipro, I hear he's got the "magic touch" with devices. No guarantees. I've heard that it's almost impossible to unbrick a device like this after an incorrect/bad radio flash.
I really hope it works out for you. Read dude, the stickies are everywhere for your benefit. Best of luck to you.
brick, htc fuze, diamond, raphael, hardspl
I run into things like this DAILY. Been a service rep for over 30 years. If people would ONLY follow the instructions, I'd have less follow up work to do.
Unfortunately they make these phones too easy to hack (good for us) but sometimes noobs make it hard for the rest of us.
lol
This is what happens when you don't follow directions, don't read enough, and are monkeying with things you obviously shouldn't be monkeying with.
When you got the device ID error, you should have stopped right there and thought "gee, maybe I should go over these instructions again and see what I did wrong" instead of trying to force a radio that will never work on your device.
Hope you can get it in to bootloader, otherwise enjoy your shiny new brick.
Well, hope you get it solved and otherwise you learned a lesson in a very expensive way I'm afraid...
Farmer Ted said:
Why didn't you just follow the instructions for flashing? You aren't even security unlocked, so why were you trying to flash a diamond radio? That makes no sense at all. Also, if you are security unlocked, you need to get diamond radios from the raphael forum, because they're patched to flash onto raphaels. It sounds like you got yours from the diamond forum, which is the wrong way to go (especially if it's a cdma radio-that would kill your phone for sure). Did hard spl work? If not, why on earth did you forge ahead? YOU CAN'T DO ANYTHING UNTIL YOU FLASH HARD SPL!!!!!
Try pulling the battery for a while, the see if it will start up. It's hard to tell what you did, but since you went down such a wrong path, I wouldn't be surprised if the phone is a giant brick.
Click to expand...
Click to collapse
I did hard SPL first with 1.90OliNex (because the one that was in the unlocking package originally didnt work beacuse of the invalid model ID message) and i thought thats what security unlocked the phone and then i tried to put a costume radio that would allow me to unlock the phone but the radio wouldnt flash. So i went back to the SPL from the unlocking package (HARD SPL 1.34) and i changed the .nbh file from DIAM***** to RAPH***** and then it bricked... The reason i did this is beacuse of the following link :
http://forum.xda-developers.com/archive/index.php/t-427305.html
I just hope something can still be done otherwise this is just a good warning for all others not to do this. Thank you for the replies
jdmsohc22 said:
You only get that error when your trying to flash the wrong device... Did you use the file "Raphael_CDMA_HSPL_037.zip" to unlock..?? Sound's to me like you used the Diamond Unlocker... Shouldn't be that hard to fix, hold the volume down button, power button, and insert stylus into the hole on the bottom to soft reset to try and open up BL screen... LMK if that works...
Click to expand...
Click to collapse
No I used a gsm unlocker, HARD SPL 1.34... There is a more detailed explanation in the post above
Hard spl 1.34 is either cdma or diamond gsm-I don't know which. I do know that it will brick a gsm touch pro. Flashing the wrong hard spl is the guaranteed way to kill a phone. If you actually flashed it, the phone is dead. Try pulling the battery for a day.
You need to run the gsm raphael unlocker to security unlock your phone. You need to pay for it, too. Hard spl doesn't security unlock your phone-it only CID unlocks it.
Farmer Ted said:
Hard spl 1.34 is either cdma or diamond gsm-I don't know which. I do know that it will brick a gsm touch pro. Flashing the wrong hard spl is the guaranteed way to kill a phone. If you actually flashed it, the phone is dead. Try pulling the battery for a day.
You need to run the gsm raphael unlocker to security unlock your phone. You need to pay for it, too. Hard spl doesn't security unlock your phone-it only CID unlocks it.
Click to expand...
Click to collapse
I used the GSM one. Ok i just pulled out the battery and hopefully the phone allows to get it into the bootloader...
Worst case scenario, smash it and pay $100 for ur insured replacement... That is, if you have insurance...
jdmsohc22 said:
Worst case scenario, smash it and pay $100 for ur insured replacement... That is, if you have insurance...
Click to expand...
Click to collapse
Hahahaha !
Good one !
But dude no offense but u deserve a black shiny 600$ brick because YOU DIDN'T FOLLOW THE INSTRUCTIONS ! THEY ARE THERE TO BE FOLLOWED UNLESS AND UNTIL YOU ARE SO RICH THAT YOU CAN WASTE 600$ OR YOU ARE A SUPER CHEF AT XDA AND ARE SURE OF WHAT YOU ARE DOING !
Anyways Best of luck hope you can unbrick it !
otherwise smash it
Bye.
LoL yeah a $600 paper weight may also come in handy..?? Or like previously stated, take your anger out on it for not doing it right the first time lol...
I now this might be a little too late to answer,but i want to give my two cents to this brick posts. Maybe someone will need it. This is for anyone that might be where I was for over 2 weeks. I though my Fuze/ Raphael / touch pro was history. My phone will get into restart loops when ever he wanted. It was very anoying. After replacing every possible software from Radio, Hard Spl, different rooms and even start up splashes, and almost getting "ORD" in the process. I finally took my phone apart, since there was no warranty. Once open I saw that the reset bottom inside was too close to the rubber reset bottom from outside. Guess what ?? That as all it was..... Good luck to all. : )