Viper’s Guide To Water Damaged PDA’s
This guide is to help anyone that has accidently left their phone in their pocket and went swimming,Went to answer a call and it fell in a puddle..etc, etc. I’ve worked for a major telecom company and have run into this situation so many times. Decided after dealing with this issue and reading so many myths, baking, rice…etc that are hit or miss and potentially very dangerous. Here’s a little guide that many people use with success to revitalize their wet cell phones.
Step 1: Immediately take the battery out of the phone and SHAKE any excess water off.
Step 2: Dry your phone first using a towel, wiping up anything that did not get shaken off. Now get a blow dryer on low heat and position it to blow on your phone about a hand, two hands length distance. Do this for about an hour or 2. Your phone should get alittle warm. If for any reason its hot to touch stop now. Let it cool off and increase the distance between the blow dryer and your phone. Also note, any ports that a covered need to be opened and memory cards, sim cards as well.
Step 3: after all visible water is gone or dry, place it in a small container (Tupperware works) slightly bigger than your phone. Now loosely pack your phone with cotton balls in your container. This works better than rice because it will not leave a white residue and it helps protect and keep your phone clean. You will let it sit overnight, at least 24 hours.
Step 4: Check on your phone, some of the cotton balls should be wet or moist. Inspect the phone, rotate it around and really look for any water. If it feels dry as a bone put the battery back in and fire it up. If it didn’t fire up check to make sure the battery is charged. If so then it may need some more time to dry out. DO NOT plug the phone into the wall charger and try to fire it up.
Step 5: If your phone did not fire up after 24hours BE PATIENT! Give it another 2 days then give it a go. It should fire up by now. If it doesn’t at that point use your wall charger. If at that point it doesn’t work, you need to consult some repairs.
Hope this helps
Thanks mate
Good stuff to be aware of it
It should be included on the Wiki (Is this possible Mods?)
Cheers,
Pretty much what I did for mine except I opened it up and dried out the internals with swabs before throwing it in rice for good measure. It worked for another month but then it started losing everything when turned off and after that the rom started corrupting. Bad luck on my part I guess.
Some of the problems related to pools are the chemicals etc. You want to have the water slowly evaporate hence the slow blow drying. If you bake you will leave a lot of the chemicals behind and thats when you get this weird looking white frost on in the inside of the screen and this WILL cause your phone internals to corrude and cause problems down the road.
Granted, I wish this was the end all be all but there are a lot of factors that can affect results. For the most part I've had good success, completely saved my 8125 and Lg Incite this way.
Another thing I forgot to mention is; if you have your phone ON when it gets wet and you try to fire it back up and it doesn't, Try a new battery. I noticed some new batteries have an 'internal memory' that could short circuit. My friend's Fuze wouldn't boot up after the 2 days, quick trip to ATT new battery fired right back up, been a week and 3days? now and it works fine.
+bumping for great justice+
if the phone was submerged in a pool i would imagine rinsing it with distilled water would do a great deal for removing pool chemicals no?
Long as its not spring water as that already contains a certain level of minerals. The other question you might want to ask yourself is; can your phone survive another dip? Completely, your judgment call on that one. You can skip it if you dry it on low heat, very slowly.
Trv06kviper said:
Long as its not spring water as that already contains a certain level of minerals. The other question you might want to ask yourself is; can your phone survive another dip? Completely, your judgment call on that one. You can skip it if you dry it on low heat, very slowly.
Click to expand...
Click to collapse
distilled water, by definition has no minerals. and pure H2O does not harm electronics. the problem is it quickly picks up contaminants and becomes conductive.
IF i dropped my phone in a heavy chemical ridden environment such as a pool i would much rather remove the battery and rinse the thing with distilled water then let those chemicals stay in the phone.
This is good information. Thanks for sharing.
Related
Hello,
My HTC Touch Cruise is falling into the water and now it's reboot in the SFR page ...
My phone is died or i can do something ?
Sorry for my english ...
Thanks
LOL
Hey man!
I think your TC is dead. If you`re a lucky guy and only if so there is an 5% chance that the device is not dead. But when the device doesnt react, its dead!!!!!
So far
Frank
First thing you had to do is to remove the battery immediatly. Than throwing the Phone in destilated water. It seems maybe wrong, but destilated water cleans all parts and removes the dirty water. After good drying time, you can try your Polaris again. I hope you didn't brick it yet, because you allready tried to start it up.
Thanks, but the Polaris is falling in the 2 months ago so i think the Polaris is died
A gadget can, quite often, survive a short dive, if the battery is removed as quick as possible, and the device is dismantled, cleaned and completely dried before reappling the power. The worst mistake ppl often do is to try and turn the device on while wet, to see if it "still works".
I still have an old Alcatel OT535 phone, fully working, after accidentally dropping it into water on a hike. All i had to do, is remove the battery immidiately, then clean the internals and dry the phone at home.
Maybe you could dry it in your oven at a very low temperature (50 Celsius). Not in the microwave obviously!
you had to remove the battery, put in the a box filled with rice for a few days, did this once with a drown ipaq, still works after 4 years
deechte said:
Maybe you could dry it in your oven at a very low temperature (50 Celsius). Not in the microwave obviously!
Click to expand...
Click to collapse
i putted my phone on my passive cooled VGA card in my PC when it fell in the water. it was dry on no-time
any place where there is low heat is good to dry your phone. just dont rush it, and take your time. better to wait one more day then have a broken device
Take off the covers, remove the sim card and battery and let it dry after you cleaned it.
Try it.
If it won't work disassemble it and de/attach the connectors.
Since it was wet and you prolly used heat to accellerate the drying
chances are that the surfaces of the metal used in the connectors
are oxydated due to interaction with "dirty" water.(is that english ?!?!) ). By de/attaching them you scratch
some of the surface clean and so restoring it somewhat.
These days electronics work with very low voltages and currents, so every
change on electrical specs due to oxyde wil influence functionality to a point
where it won't work, boot, synch or operate.
That's how i saved quite a few phones that where "abandoned" due to waterdamage.
Microphones, speakers and shielded parts of the pcb can take a while to dry completely.
Oki I tried it
Thanks You
Works for me !!!
My little child took my Nokia phone into the sea. Tried to recover it without luck.
Two months later a friend of mine told me to put the phone inside some thick socks and take it inside a tumble dryer.
Sounds crazy but phone is working now !
I may have possibly water damaged my Captivate last night. It was in my pocket when water spilled on my lap, and I didn't immediately take it out. Very stupid of me. The USB port was open so I'm thinking liquid may have gotten into there... Also, there were water beads on the inside of the camera lens.
My recourse was to take it apart and try to let it dry out. Initially it wouldn't do anything upon being plugged in to the charger, so naturally I thought it was bricked. I've let it sit all day on a dry window sill next to the radiator. After putting the battery back in and plugging it in a little bit ago, the phone surprisingly booted up. Here's where I'm at now:
The phone boots normally, however if I plug it in to the charger I get an error stating Battery Temperature too high or something, so charging is paused. Does anybody know what this indicates?
Secondly, after being on for a minute or so, the screen gets screwy. Dark transparent overlays start flashing over everything and it gets unresponsive... I haven't left it on like this long b/c I was afraid something worse would happen - I usually rip the battery out of the back to shut it off.
My phones currently pulled apart and drying in the window sill. Whatever water got on/in it is not visibly there, however I understand some parts might still be wet.
Any advice? Also, I believe the water indicator on the battery and near the pins where the battery dock in the phone are both fine. They're white squares and haven't changed color. Any chance there are other indicators?
The phone isn't insured and I bought it back in August. Would warranty possibly cover this or will they know about the water damage?
jmusso said:
I may have possibly water damaged my Captivate last night. It was in my pocket when water spilled on my lap, and I didn't immediately take it out. Very stupid of me. The USB port was open so I'm thinking liquid may have gotten into there... Also, there were water beads on the inside of the camera lens.
My recourse was to take it apart and try to let it dry out. Initially it wouldn't do anything upon being plugged in to the charger, so naturally I thought it was bricked. I've let it sit all day on a dry window sill next to the radiator. After putting the battery back in and plugging it in a little bit ago, the phone surprisingly booted up. Here's where I'm at now:
The phone boots normally, however if I plug it in to the charger I get an error stating Battery Temperature too high or something, so charging is paused. Does anybody know what this indicates?
Secondly, after being on for a minute or so, the screen gets screwy. Dark transparent overlays start flashing over everything and it gets unresponsive... I haven't left it on like this long b/c I was afraid something worse would happen - I usually rip the battery out of the back to shut it off.
My phones currently pulled apart and drying in the window sill. Whatever water got on/in it is not visibly there, however I understand some parts might still be wet.
Any advice? Also, I believe the water indicator on the battery and near the pins where the battery dock in the phone are both fine. They're white squares and haven't changed color. Any chance there are other indicators?
The phone isn't insured and I bought it back in August. Would warranty possibly cover this or will they know about the water damage?
Click to expand...
Click to collapse
well you want to put in rice, so that the moisture is gone
rice it for sure. but warranty WILL not cover it UNLESS the tabs on the battery and phone are white (It might not have gotten wet if it was in your pocket)
if they are still white, or if your phone is white and battery red (then buy another battery) and get to the store and tell them you don't know what is wrong with it. The only indication that it is water damaged is if it is red and those tags are notoriously faulty so you could always argue your way through it if you have an account in good standing.
best of luck.
I know someone who "claimed' that insurance was supposed to be added to the phone when he got it and noticed that the person didn't do it properly (the guy was new so it helped his cause) and the manager of the cor store told him that they'd do a courtesy replacement and charged him the 125$ for a new device.
you could go that route should you need too...
I don't have access to rice at the moment... Would it do any good even if I absolutely can see no water anywhere in/on the phone?
Am I doing my phone any harm/potential harm by trying to turn it on every once in a while, or should I just let it be for a few days?
Take the phone apart and focus the strongest fan you have on it over night. It's probably best to not turn it on for awhile. Maybe if you focus a blow drier on it for perhaps several hours, air will find flow through the small openings within the case.
You may not be able to dry some parts of it unless you do a complete dismantle, but that may require special tools
Consider shipping it to get repaired only as a last resort, as I've read some bad reports about that.
Rice or some other dessicant is the way to go - it will pull moisture out. Also, turning it on (even putting the battery in) is bad - you are powering circuits and possibly creating shorts where water is present. You may have already done permanent damage.
If you get electronics wet, the best course of action is to remove the battery and put it in a bag of rice for a few days.
Now that You have the phone apart get an alcohol pad and gentley scrub the main board. Sometimes when liquid touches the main board you will get a white looking residue. If you see anything like that simply wipe it off. I dropped my phone into a trash can at a very popular teriyaki restaurant here in Las Vegas my phone was submerged into a deep bath of teriyaki sauce. I quickly pulled the phone from the can and wiped it down vigorously. I was excited to see that it was initially working unfortunately this was not the case by the time I got home. The phone would not turn on for a whole week, until I decided that I was going to open her up. I found a tutorial on line describing a complete break down of the captivate. Upon opening it I found I was able to see exactly where the teriyaki had interacted with the electronics due to the remnants of an oxidized white film that was present on various parts of the main board. I grabbed a alcohol pad out of my first aid kit and began wiping it down to remove all of the white stuff,put the phone back together and to my surprise it turned on. Hope this helps!
Thanks for the info guys.
How would I go about getting to the "main board"? Taking out the battery and looking inside it only reveals where the battery connects, where the SD card and sim cards can go... I'm assuming if I remove the little screws around that fixture I can get to the "main board"?
I think I can see some minor corrosion around where the sim card connects, but I think I *should* be able to clean that with some alcohol.
The phone seems to be working fine (I've yet to put my SIM back in it, though, so no idea if the corrosion around there is affecting it at all). I just booted it up and was able to get on the web (wifi), run apps, everything just fine. Didn't get the flashy screens I mentioned earlier. However, if I plug in the USB charger, it still gives me the temperature error. I didn't keep it plugged in, however it did make me realize something:
The errors I was getting before, where the screen went all wacky, only happened if the phone was plugged in to the wall. Is it possible my battery is busted, or do you think the USB charger is busted? Remember that port was open when it happened.
Any thoughts? New battery? Or do you think I won't be able to charge the phone via USB charger any more?
jmusso said:
I don't have access to rice at the moment... Would it do any good even if I absolutely can see no water anywhere in/on the phone?
Am I doing my phone any harm/potential harm by trying to turn it on every once in a while, or should I just let it be for a few days?
Click to expand...
Click to collapse
yes you are, because if there is water or moisture internal, it can short circuit, also rice will help dry up the phone completely
jmusso said:
Thanks for the info guys.
How would I go about getting to the "main board"? Taking out the battery and looking inside it only reveals where the battery connects, where the SD card and sim cards can go... I'm assuming if I remove the little screws around that fixture I can get to the "main board"?
I think I can see some minor corrosion around where the sim card connects, but I think I *should* be able to clean that with some alcohol.
The phone seems to be working fine (I've yet to put my SIM back in it, though, so no idea if the corrosion around there is affecting it at all). I just booted it up and was able to get on the web (wifi), run apps, everything just fine. Didn't get the flashy screens I mentioned earlier. However, if I plug in the USB charger, it still gives me the temperature error. I didn't keep it plugged in, however it did make me realize something:
The errors I was getting before, where the screen went all wacky, only happened if the phone was plugged in to the wall. Is it possible my battery is busted, or do you think the USB charger is busted? Remember that port was open when it happened.
Any thoughts? New battery? Or do you think I won't be able to charge the phone via USB charger any more?
Click to expand...
Click to collapse
If you've never taken apart a smart phone before, and reading your first question, I'm going to assume that's the case, then I strongly advise you not attempt it unless you are willing to either A) buy a replacement after you break it or B) invest time/money into repairing mistakes you've made. This phone is not as difficult to disassemble as some, but I wouldn't want to break that $150 amoled screen.
No, removing the screws will not simply get you to the mainboard. It's more complicated and nuanced than that.
I'm a new user so I can't post the link but if you google Tech Republic Captivate tear down [/B]there is a website that will show you step by step how take the phone apart. There are two screws under the clip you pull down to take the back cover off. Be careful when pulling it back to expose the screws. I tugged on it pretty hard with no problems, but I imagine it could be broken if you pull too hard. Good Luck! It's actually really easy to take apart and the various ribbon connectors on the main board are really easy to unplug and plug back in after cleaning it.
So what do you guys think I should do if I'm still getting the battery error with the thermometer and yellow caution sign? Buy a new battery? Or do you think its the USB jack? Has anybody seen this before - the battery was working fine as long as it was not charging.
I'm trying to decide between a) buying a new battery, or b) buying a wall-mounted battery charger since the USB won't charge the phone.
Anybody have any experience?
Meguro2006 said:
I'm a new user so I can't post the link but if you google Tech Republic Captivate tear down [/B]there is a website that will show you step by step how take the phone apart. There are two screws under the clip you pull down to take the back cover off. Be careful when pulling it back to expose the screws. I tugged on it pretty hard with no problems, but I imagine it could be broken if you pull too hard. Good Luck! It's actually really easy to take apart and the various ribbon connectors on the main board are really easy to unplug and plug back in after cleaning it.
Click to expand...
Click to collapse
I think you need to be careful about who you encourage to dissect their device. This guy asked how to get to the mainboard. Clearly, he hasn't opened a smart phone before. Telling him it's "actually really easy" is disingenuous at best. Performing smart phone repairs properly requires experience. I'm certainly not suggesting that noobs not try to fix their phones, only that they are made fully aware of the risks.
My Captivate was fully submerged in dirty water. I followed some instructions online and it's been working fine for over a month now. If your water-detection stickers are already red anyway, and rice isn't working, I recommend it:
1) Remove battery, SIM card, SD card
2) Submerge in a bowl of distilled water and gently agitate. This helps clean the insides. Distilled water (not spring water) does not conduct electricity.
3) Next, submerge in a bowl of high-quality rubbing alcohol (~95% pure) and gently agitate. Rubbing alcohol displaces water, removes corrosion, and evaporates quickly. (It's also flammable, so have good ventilation and no open flames nearby)
4) Leave it out to dry for two days or until it no longer smells of alcohol.
BTW I wouldn't dry it too close to a radiator, the heat may damage it.
jatkins09 said:
If you've never taken apart a smart phone before, and reading your first question, I'm going to assume that's the case, then I strongly advise you not attempt it unless you are willing to either A) buy a replacement after you break it or B) invest time/money into repairing mistakes you've made. This phone is not as difficult to disassemble as some, but I wouldn't want to break that $150 amoled screen.
No, removing the screws will not simply get you to the mainboard. It's more complicated and nuanced than that.
Click to expand...
Click to collapse
Not really. Once the screws are removed..including the two hidden by the battery cover lock slider...you can carefully pry the cover apart using your fingernail to get to the the internals. I have done it several times and am no expert by any means. Just don't yank like you are opening a present on Christmas morning.
Although I am mystified by the op stating they have no access to rice?! That should always be the second thing one does after a moisture incident...right after pulling the battery and sim. I guess in this case a trip to the store with a couple bucks may have pushed that to step three though..
sent from my captivate disguised as an i9000 running cyanogen
Hello,
by a rediculous accident I forgot my HTC Diamond in the pocket of my jeans when running the laundry :-(
Afterwards, I opened the cover, took out the battery and let the phone dry out for 2 days. Now I've put it back together, and connected it to the charger. The "ring" is flashing, so the battery is charging but the phone itself is not starting and the display remains completely black, not even the vibration kick on starting...
Is there anything I could do? Or perhaps there is a chance to get out some photos I have shot earlier, would also be something...
ive heard that taking apart your phone and leaving the parts in rice can help (because the rice absorbs moisture)
Off topic:
I read one Desire went through a washing sequence in a washing machine in Desire spesific forum and now this?
Is this a new hobby? I mean... washing smartphone
darkman088 said:
Or perhaps there is a chance to get out some photos I have shot earlier, would also be something...
Click to expand...
Click to collapse
If the photos are on your micro sd card, you may be able to plug that into an adapter and plug it into your PC and gain access to them that way. Just be sure that micro sd card is thoroughly dry before doing so.
WORKING !!!
Hello,
thanks for the replies... This morning the phone booted!!! I was able to download the photos!!! But the screen has stains, obviously the remaining water.
PLEASE advise on how to dry that thing completely !!!
I think that I'm gonna pass on the rice thing.
@aaa - YOU ARE A JUNKA$$ !!! You think that's really funny?!? Especially when I'm currently TIGHT on budget and need the money for other things and the next phone is planned no earlier than Christmas... I'm hesitating whether you're a real human being...
You can dry it completely in an oven for three hours at thirty degrees or so. I've done this three times. If you have a fan forced oven, just turn the fans on, that'll be enough.
A safer way (if you can obtain it) is to leave the phone for 24 hours in a bowl of dessicant silica gel. You'll often get a small packet of silica gel when buying new electronics or other moisture-affected things. That small packet is enough, just put it in an airtight bag and leave it for 24 hours.
The next step would be disassembly and a thorough swabbing with denatured alcohol, but that's pretty extreme and only needed when the device isn't booting.
Some LCDs are hard to get moisture out of, some are not. Leaving the phone with the silica gel for longer will have a better effect. As the previous poster mentioned, rice also works (quite well), but takes longer than silica.
Good luck with it!
Another thin that will absorb moisture is common table salt. Take the phone apart very carefully. Remove battery first, make sure you're grounded as well.
Hello everybody.
thanks a lot for the numerous advices...
Unfortunately, I have more to report...
The phone dried out and booted 2 or 3 days later, as I said. The stains on the display disappeared as by magic one day later.
Everything was fine for a week until I launched the camera 2 days ago. The backlight of the display went off and came back only after removing the batter for 15 minutes.
Now the backlight is going off pretty often, sometimes it requires to remove the battery 1-2 times before it starts working again and yesterday it happened that it got activated again when I got a call...
Any ideas please?
And also the phone keeps overheating from time to time without real load (GPS or wi-fi) which dries out the battery. But I had this problem also before the laundry
Sounds like that moisture in the LCD unit left a bit of residue and is shorting the backlight somewhere.
Only option there would be to disassemble and swab the LCD boards and cables/connectors with denatured alcohol.
Alternatively, a new LCD unit should fix the problem if it persists, just make sure you alcohol swab the connectors before plugging them back in
Someone also mentioned drying out in salt before. While that does work, salt is extremely corrosive on solder and SMCs, so I wouldn't recommend that route.
i heard hair dryers are the bomb at the screen moisture, just take off all that you can and blow dry it.
I just don't understand your refusal on using white rice. It have saved countless phones.
Uncooked white rice is VERY mosture negative. Just put layer of rice, put your phone on it, cover it completely with white rice, seal it in. Ziploc could work too.
In a day or two your partially dry phone will be bone-dry. If it was soaked still you could first try to shake out water as much as can, soak it in distilled water to remove minerals, then white rice it for 3 to 5 days.
I had this problem with my Touch Diamond. Everything worked, but while i was trying to dry it I broke one of the battery "hinges" but the phone still worked after except only with black screen. The best thing to do probably is just leave it for a couple of days and hopefully your phone will be back!
XXCoder said:
I just don't understand your refusal on using white rice. It have saved countless phones.
Uncooked white rice is VERY mosture negative. Just put layer of rice, put your phone on it, cover it completely with white rice, seal it in. Ziploc could work too.
In a day or two your partially dry phone will be bone-dry. If it was soaked still you could first try to shake out water as much as can, soak it in distilled water to remove minerals, then white rice it for 3 to 5 days.
Click to expand...
Click to collapse
exactly what ive said. ive read everywhere that rice is one of the best solutions out there
Like was said before you most likely have some corrosion on a few contacts, if you have about 6 bucks you can spare you can get residue free contact cleaner in an aerosol at radio shack or any electronics store and save yourself having to scrub each contact and connector. Just tear the phone down down spray all the contacts and connectors with contact cleaner let it sit for a few then spray it down with air duster to get any thats get under the resistors, in the connectors, etc that hasn't dried; let it sit till you're positive everythings dry and put it back together. Does the same thing as alcohol just alot less scrubbing.
Sent from my i897 w/Andromeda 3, Suckerpunch kernel, & 1.3Ghz OC using Tegrak.
Hello,
thanks for narrowing the problem down.
But for me it looks like something different, because:
1) I have been using the phone for 1 week without any problems and it got screwed after I've launched the camera app for the first time
2) The backlight works when I power on the phone. But its stop is event-triggered, like when I launch the sound or video player or when I get a call... Similar events would trigger the backlight back on.
Perhaps reflashing the software could fix that?
I went to a shop today and put another battery. The phone booted, anyway without any backlight, twice...
At least the device is still alive.
There probably was a tiny water bubble and it messed with phone when you turned camera on.
darkman088 said:
Hello,
thanks for narrowing the problem down.
But for me it looks like something different, because:
1) I have been using the phone for 1 week without any problems and it got screwed after I've launched the camera app for the first time
2) The backlight works when I power on the phone. But its stop is event-triggered, like when I launch the sound or video player or when I get a call... Similar events would trigger the backlight back on.
Perhaps reflashing the software could fix that?
I went to a shop today and put another battery. The phone booted, anyway without any backlight, twice...
At least the device is still alive.
Click to expand...
Click to collapse
remove the back cover and battery from the phone, and put everyting in a bowl of rice for a day,. should fix everything,
XXCoder said:
There probably was a tiny water bubble and it messed with phone when you turned camera on.
Click to expand...
Click to collapse
Either that or a short in the cameras circuit from corrosion, either way i'd pull it apart before it gets worse and check it out.
Sent from my i897 w/Andromeda 3, Suckerpunch kernel, & 1.3Ghz OC using Tegrak.
ok i got my phone wet what do i do i put it in the rice
I've heard that works, I don't know how long you keep it in there.
Take the battery out and do not try to turn it on or it will like short circuit or something like that.
/my little knowledge.
well i did turn it off and then back on
Put it in rice for a day or so.
will that fix the button issue
Most likely. The button problem is caused by water completing the circuit between the button and the point of contact, so putting your SK in the rice will almost certainly fix your problem (just be sure to be patient and wait a day or two).
worst comes to worst buy on on ebay for 75 bucks
thank you guys u made me feel so much better
well it didnt fix it
you gotta wait a few days man now its probably done-zo
what you mean
you have to let it sit in rice for a couple days, the water will cause corrosion and over time will mess up the circuits, rice will dry it out over the course of a few days then it would be fine but if you pump electric through it you can cause things to permanently be damaged
If you are some what mechanically inclined, you can disassemble your phone so it can completely dry. All you will need is a micro screw driver set (usually find at hardware or tool store) and youtube has a good collection of dis-assembly videos. The proper way to service a water damaged smart phone would be to disassemble and place in an ultrasonic cleaner with alcohol or other chemical to remove water. Might check your local area for a phone repair shop, they usually have all the tools to get your phone repaired correctly so you don't end up with a button that doesn't work or worst problems later on from corrosion. Hope this helps
im confussed
What blk2dr is saying is that over time, the water can cause damage to your phone (if it isn't dried quickly). He recommends that, if you think you are able, you should take your phone apart so that it can dry faster.
If you aren't confident in your ability to take your phone apart and put it back together, I recommend you just slide the screen up, take the battery cover off, remove the battery and SIM card (and microSD if you have one in there), and put it back in the rice.
How long did you keep your SK in the rice the first time?
over night i tired it when i woke up and it still didnt work
Perhaps there is some water left.Maybe it condensed. Try taking it apart and see if there are any drops left.Also don't get tempted to use a hair drier since it cpuld melt some circuits and wire connections.
Sent from my Optimus Me using xda premium
i think the phone is trashed the battery and the phones water thingy is red
listen, of course its red, but you needed to let it sit in the rice longer, its not going to dry out in 12 hours
its going to take days, and by trying it over and over youre just doing more damage
i will try it tomorrow morning
Did you leave it in your pocket and run it through the washing machine and at times it's possible that your friends dunked you in a swimming pool just for the fun of it? Did you get beaten by the rain or did you forget and go swimming with your cell phone in your pocket? Or perhaps it fell out of your pocket and into the pet's water bowl?
If you drop your cell phone in water, it is often possible to salvage it. Time is of the essence, however, so the first thing to do is to get your cell phone out of the water as soon as possible. Leaving a cell phone in water for even a few seconds might damage it beyond repair, but there are a few things that you can try and that sometimes work. The main things are opening the phone as much as possible, taking out the battery and completely drying off all of the components.
Step 1
Remove the battery from the phone, if possible, or at least turn the phone off. Most of the damage you are trying to prevent occurs when the device is electrified, so removing the battery helps considerably.
Step 2
Disassemble the device, if possible. This should only be done if you have taken your phone apart before and feel comfortable doing it. This will speed up the drying process as you can easily remove water from around the circuit board. This will void your warranty, but if your phone is wet the warranty is no longer in effect anyway.
Step 3
Blow compressed air on the device to remove as much water as possible. If you didn't disassemble your device, blow the air into a port or earpiece opening to try and force water out of another hole. Continue until no more water comes out of the device.
Step 4
Fill a container three-quarters full with dry, uncooked rice. Submerge your phone, or all the pieces of it, into the rice. Seal the container.
Step 5
Wait 48 hours for the rice to do its job, then open the container, reassemble the device and turn it on.
Tips
Dry rice is most often recommended because it is likely to already be in your possession and time is of the essence. Other desiccants, like silica gel packets or calcium chloride, will work faster and if they are on hand, would be preferable to rice.
BAD LUCK....: O
via XDA Premium
wet phone
poordonnao said:
Did you leave it in your pocket and run it through the washing machine and at times it's possible that your friends dunked you in a swimming pool just for the fun of it? Did you get beaten by the rain or did you forget and go swimming with your cell phone in your pocket? Or perhaps it fell out of your pocket and into the pet's water bowl?
If you drop your cell phone in water, it is often possible to salvage it. Time is of the essence, however, so the first thing to do is to get your cell phone out of the water as soon as possible. Leaving a cell phone in water for even a few seconds might damage it beyond repair, but there are a few things that you can try and that sometimes work. The main things are opening the phone as much as possible, taking out the battery and completely drying off all of the components.
Step 1
Remove the battery from the phone, if possible, or at least turn the phone off. Most of the damage you are trying to prevent occurs when the device is electrified, so removing the battery helps considerably.
Step 2
Disassemble the device, if possible. This should only be done if you have taken your phone apart before and feel comfortable doing it. This will speed up the drying process as you can easily remove water from around the circuit board. This will void your warranty, but if your phone is wet the warranty is no longer in effect anyway.
Step 3
Blow compressed air on the device to remove as much water as possible. If you didn't disassemble your device, blow the air into a port or earpiece opening to try and force water out of another hole. Continue until no more water comes out of the device.
Step 4
Fill a container three-quarters full with dry, uncooked rice. Submerge your phone, or all the pieces of it, into the rice. Seal the container.
Step 5
Wait 48 hours for the rice to do its job, then open the container, reassemble the device and turn it on.
Tips
Dry rice is most often recommended because it is likely to already be in your possession and time is of the essence. Other desiccants, like silica gel packets or calcium chloride, will work faster and if they are on hand, would be preferable to rice.
Click to expand...
Click to collapse
Put it in rice. At night a couple of asian guys will come and fix it.
Rice! I've saved a phone and an iPod this way. Hope it works