Hi, I've been a lurker here for quite some time but this is my first post.
I just tried to upgrade my Verizon XV6700 from AKU2.2 to AKU3.3 using the RUU I downloaded from the pcdphones.com web site (APA_Verizon_31430_314208_14300_WWE_Ship_2.exe). The RUU correctly identified my current radio, CE and Extended firmware versions but failed during the upgrade with error 116 (General Error). Doing a hard reset on the phone brings up the reset screen but after clearing the memory the phone just displays a blank screen. I can manually get into the bootloader (USB v2.05) and I tried re-running the AKU3.3 RUU again but now it says that my model ID is incorrect. I also tried running the AKU2.2 RUU (APA_VZW_20720_206_11000_WWE_Ship.exe) to get back to my original state but it doesn't work either (Error 101 Connection Error).
I downloaded Newbootloader_RUU and tried copying the 3 .nbf files for AKU3.3 into the directory and it seems to upgrade but it only runs for a short time (less than a minute) before saying the upgrade is complete and after doing a hard reset I still get a blank screen. I suspect that the ROM was not actually upgraded.
I downloaded mtty1.43 and I can get to a USB> prompt and have tried a few of the suggestions I found on the forums here but none have helped. I suspect that the model ID and possibly other information may have been corrupted by my first upgrade attempt. Here's some of the info I've recorded:
USB>info 1
2.05
USB>info 2
VZW__001 9ÿmïHTCE
USB>info 3
PA10A1ä TÝHTCE
USB>info 4
[email protected]ๆHTCE
USB>info 5
USB>info 6
T ÚÈÒHTCE
USB>info 7
HTC Integrated Re-Flash Utility for bootloader Version : 1.50a, APACHE HW Version : 2.05
Built at: Sep 18 2007 21:54:57
Copyright (c) 1998-2005 High Tech Computer Corporation
Turbo = 312 MHz, Run = 208 Mhz
Memory Frequency = 208 MHz
SDRAM Frequency = 104 MHz
Board ID is 2, Display is 0 (0=Ty,1=Sg)
USB>info 8
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0xA00000
FAT2 Size: 0x2840000
All Size: 0x7340000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000,FAT2_ADDR=0x4B00000
USB>info 9
USB>
Before I attempted the upgrade I recorded some information from the phone. I don't know how useful it might be but here it is:
Verizon XV6700 Startup Splash Screen:
H/W = 2
M = 12
U = 4
P SNAZ-40306
R 1.10.00
D 2.07.20 WWE
Device Information, Version:
ROM version 2.07.20 WWE
ROM date 02/24/06
Radio version 1.10.00
Protocol version SNAZ-40306
ExtROM version 2.07.200 WWE
Hardware version 0041
PRL version 51344
PRI version 1.14_002
Browser version MSIE 4.01
ESN 3674D2B4
Device Information, Hardware:
CPU Intel(R) PXA270
Speed 416 MHz
RAM size 64 MB
Flash size 128 MB
Flash chip type M-Systems
Data bus 32 bits
Storage size 39.59 MB
LCD 240 x 320 TFT
Colors 65536
Device Information, Identity:
Model No. PA10A1
Platform PocketPC
About, Version:
Microsoft Windows Mobile Version 5.0
OS 5.1.195 (Build 14928.2.2.0)
Processor: PXA270-416MHz
Memory: 49.23 MB
At this point I would welcome any suggestions. I've searched through the forums here but I haven't come up with anything else to try.
Thanks for your help.
Related
Hello Everyone,
I have an i-mate Jamin, G3 I believe with no sign of life. The battery is 100% charged, and I cannot enter bootloader mode.
So I'm trying JTAG to write bootloader back to the phone.
My steps
1. I installed GIVEIO driver and started the service in Windows.
2. I made the JTAG pins using the resistance and connected the device.
3. In Jflash_MM I started start.bat and the phone was detected.
But next, I dunno what to do.
Sometimes I get error messages. Once I was even able to program. But I dunno what file to write to the device, and what is the address for this phone.
If anyone has restored the bootloader, please advice. Also is it possible on this phone or not.
Thnx
Output
C:\>start.bat
C:\>jflashmm pxa27x32 ebo_a.nb0 N 0 PAR
JFLASH Version 5.01.007
COPYRIGHT (C) 2000 - 2003 Intel Corporation
PLATFORM SELECTION:
Processor= PXA27x
Development System= Mainstone
Data Version= 1.00.001
PXA27x revision ??
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: FFC2
Lower half reads: 0
Failed to read the Flash ID. Retrying 4 more times...
Failed to read the Flash ID. Retrying 3 more times...
Failed to read the Flash ID. Retrying 2 more times...
Failed to read the Flash ID. Retrying 1 more times...
Failed to read the Flash ID. Retrying 0 more times...
Cannot open input file: Flash_ffff_2_32.dat
This program supports flash devices defined by DAT files
contained in the same directory as the executable program.
If the file cannot be opened, there are four possibilities:
1 - The flash device installed is not supported.
2 - The flash device is a licensed product.
3 - The device ID could not be read, resulting in a poorly
constructed filename. The first numeric value in the
filename is the device ID. Verify this value with the
component specification.
4 - The memory bus is not functional. Check all CPLD and FPGA
devices. Make sure that you are using the correct
platform data file.
C:\>jflashmm pxa27x32 ebo_a.nb0 N 3F40000 PAR
JFLASH Version 5.01.007
COPYRIGHT (C) 2000 - 2003 Intel Corporation
PLATFORM SELECTION:
Processor= PXA27x
Development System= Mainstone
Data Version= 1.00.001
PXA27x revision ??
Failed to read the Flash ID. Retrying 4 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 9800
Lower half reads: 0
Failed to read the Flash ID. Retrying 3 more times...
Failed to read the Flash ID. Retrying 2 more times...
Failed to read the Flash ID. Retrying 1 more times...
Failed to read the Flash ID. Retrying 0 more times...
Cannot open input file: Flash_0_2_32.dat
This program supports flash devices defined by DAT files
contained in the same directory as the executable program.
If the file cannot be opened, there are four possibilities:
1 - The flash device installed is not supported.
2 - The flash device is a licensed product.
3 - The device ID could not be read, resulting in a poorly
constructed filename. The first numeric value in the
filename is the device ID. Verify this value with the
component specification.
4 - The memory bus is not functional. Check all CPLD and FPGA
devices. Make sure that you are using the correct
platform data file.
What is this Flash_0_2_32.dat all about?
Allright, I got the device flashed too, but still no bootloader....
JFLASH Version 5.01.007
COPYRIGHT (C) 2000 - 2003 Intel Corporation
PLATFORM SELECTION:
Processor= PXA27x
Development System= Mainstone
Data Version= 1.00.001
PXA27x revision ??
Found flash type: 28F256L18B
The last 43 percent of image file is all zeros
Would you like to save time by not programming that area? [y/n]: y
Unlocking block at address 0
Erasing block at address 0
Unlocking block at address 10000
Erasing block at address 10000
Unlocking block at address 20000
Erasing block at address 20000
Unlocking block at address 30000
Erasing block at address 30000
Unlocking block at address 40000
Erasing block at address 40000
Starting programming
Using BUFFER programming mode...
Writing flash at hex address 48cc0, 99.38% done
Programming done
C:\>jflashmm pxa27x32 ebo_a.nb0 N 3F40000 PAR
JFLASH Version 5.01.007
COPYRIGHT (C) 2000 - 2003 Intel Corporation
PLATFORM SELECTION:
Processor= PXA27x
Development System= Mainstone
Data Version= 1.00.001
PXA27x revision ??
Found flash type: 28F256L18B
The last 43 percent of image file is all zeros
Would you like to save time by not programming that area? [y/n]: y
Unlocking block at address 3f40000
Erasing block at address 3f40000
Unlocking block at address 3f80000
Erasing block at address 3f80000
Starting programming
Using BUFFER programming mode...
Writing flash at hex address 3f88c40, 99.34% done
Programming done
Hi. I'm trying to install linux onto my pda as im sick of windows mobile. I've managed to un-tar the Angstrom distro and the boot image file onto their correct partitions. This is how my partitions are set-up:
Disk /dev/mmcblk0: 2059 MB, 2059403264 bytes
4 heads, 16 sectors/track, 62848 cylinders
Units = cylinders of 64 * 512 = 32768 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/mmcblk0p1 * 1 610 19512 6 FAT16
/dev/mmcblk0p2 611 62848 1991616 83 Linux
I boot the SD-card and load linux. But i'm getting a kernel panic as follows:
VFS: Cannot open root device "mmcblk0p2" or unknown-block(0,0).
I don't know what to do! I'm really stuck and i cannot stand windows mobile 6, i really cannot. Could somebody really help me please.
Thanks people.
Welcome to forums
As we dedicate only to HTC devices, unless your device is listed on the Wiki
http://wiki.xda-developers.com/
Better try here:
http://www.pdastreet.com/forums/forumdisplay.php?f=12
I bought a Literati for only $65 shipped and was thinking maybe android could be ported to this device.
CPU:S3C6410 [email protected]
Audio: None
Camera: None
Touch screen: None
Screen: Color 7" unknown X Unknown
Memory
SD: up to 16gig
User: 256mb(black) expandable to 1gb once telnet is enabled.
System: 64mb(i think)
USB
Mini USB: Mode=device
internal USB: Mode=Host(currently connected to a wireless dongle)
Network
Wifi: rt2860sta
3G: None
Ethernet: None
NAND 512MiB 3,3V 8-bit
0x00000000-0x00040000 : "Bootloader"
0x00040000-0x00340000 : "Kernel"
0x00340000-0x00d40000 : "resource"
0x00d40000-0x11140000 : "File System 1"
0x11140000-0x20000000 : "User space"
The Bootloader is:
U-Boot 1.1.6-g794ab523-dirty (Aug 23 2010 - 00:52:53) for SMDK6410
The Environment has:
bootargs=console=ttySAC0,115200 loglevel=0 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs
bootcmd=nand read c0008000 40000 300000;bootm c0008000
bootdelay=0
baudrate=115200
ethaddr=[MAC of Literati]
ipaddr=192.168.1.28
serverip=192.168.1.27
gatewayip=192.168.1.2
netmask=255.255.255.0
The Kernel is:
Linux (none) 2.6.24.2 #180 Mon Aug 23 00:49:07 CST 2010 armv6l GNU/Linux
The resource:
It begins with FILE_SECTION04 and then a file directory which shows logo.bin, update.bin, and zImage_rfs.
Here is the development website with more information http://literatidevs.com
Just got one of these today, actually. I looked up and down that board, but didn't find any info on enabling telnet. You have a link handy?
need helpe for thes p999 login prblem and info by lg tool
Connecting with P999
For connect with phone you must:
1. Unplug usb cable and reconnect battery
2. Press VolDown-key & PowerUp-key and wait for LG logo
3. Release PowerUp-key and wait for Download logo
4. Release VolDown-key and plug usb cable
Connected
Receiving phone info
Getting phone info
Model: P999
Platform: LG Qualcomm
Software Platform: Android
SDRAM Size: 64 MB + 512 MB
NAND Flash Size: 128 MB + 8 GB
CPU: MDM6200 + NVIDIA Tegra AP20H
Firmware Released: Mar 27 2011 10:12:24
Firmware Compiled: MAR 27 2011 10:00:00
Firmware Version: P9992097/M6600A-SCAUTNZ-2.0.9720T
IMEI: 012571-00-273213-5
Bluetooth Address: B0:89:91:E9:E1:03
Flash Device Name: H8BCS0QG0MMR
Flash Vendor ID: 0x000000ad
Flash Product ID: 0x000000b1
Flash FS Blocks: 0x000001c2
Flash Pages Per Block: 0x00000040
Flash Bytes Per Page: 0x00000800
Flash Bytes Per Spare: 0x00000040
Connect mode: Normal
Info received
Receiving phone info
Getting phone info
Model: P999
Platform: LG Qualcomm
Software Platform: Android
SDRAM Size: 64 MB + 512 MB
NAND Flash Size: 128 MB + 8 GB
CPU: MDM6200 + NVIDIA Tegra AP20H
Firmware Released: Mar 27 2011 10:12:24
Firmware Compiled: MAR 27 2011 10:00:00
Firmware Version: P9992097/M6600A-SCAUTNZ-2.0.9720T
IMEI: 012571-00-273213-5
Bluetooth Address: B0:89:91:E9:E1:03
Flash Device Name: H8BCS0QG0MMR
Flash Vendor ID: 0x000000ad
Flash Product ID: 0x000000b1
Flash FS Blocks: 0x000001c2
Flash Pages Per Block: 0x00000040
Flash Bytes Per Page: 0x00000800
Flash Bytes Per Spare: 0x00000040
Connect mode: Normal
Info received
Restoring to factory defaults
This phone require manual Factory Reset.
For Factory Reset you must:
1. Unplug usb cable and battery.
2. Plug battery and power on phone.
3. Type code 1809#*999# to call Qualcomm menu.
4. Go to "Factory Reset", select "OK" and reboot the phone.
5. Factory reset must be completed after next boot.
Factory defaults successfully restored
Unlocking phone
Unlock: Start
Getting phone info...
Getting phone info: OK
Switching to internal loader...
Switching to internal loader: OK
Sending external loader...
Sending external loader: OK
Switching to external loader...
Switching to external loader: OK
Dumping Security...
Dumping Security: OK
Backuping Security to file: Backups\P999_security_012571002732135_2012-5-5_6-15-53.sbf
Unlocking Security: OK
Flashing Security...
Flashing Security: OK
Switching to normal mode...
Switching to normal mode: OK
Unlock: Finish
Phone successfully unlocked
Don't forget to reconnect battery
Disconnected
hey guys..
i have a module which called bus multimedia.. i need root or read full backup of this device.. but there is no usb socket only exist RX TX pinout and i cannot connect it to pc over putty.. is anyone help me to read backup.?
t-mobile_mda said:
hey guys..
i have a module which called bus multimedia.. i need root or read full backup of this device.. but there is no usb socket only exist RX TX pinout and i cannot connect it to pc over putty.. is anyone help me to read backup.?
Click to expand...
Click to collapse
hey.. i removed the emmc and info..do u think that this device is android based..?
HiPower mode is On
Setting Interface to EasyJtag1/ISP_HiPower
Setting IO Levels to 3.3V
Setting Frequence to 21 Mhz
Setting BusWidth to 1 Bit
CMD Pullup Level: 2134 mV
CMD Active Level: 2609 mV
Setting HS Timing to Enabled
EMMC Device Information :
EMMC CID: 7001004D3732383038801500009374CA
EMMC CSD: D04F01320F5903FFFFFFFFEF8A400060
Manufacturer: KINGSTONE , NAME: M72808 , HEX: 4D3732383038 , S/N: 15000093 , Rev: 80
Manufacturer ID: 70 , OEM ID: 00 , Device Type: BGA (Discrete embedded) , Date: 7/2017
EMMC ROM 1 (Main User Data) Capacity: 7296 MB (0x0001C8000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (0x000000400000)
EMMC RPMB Capacity: 4096 KB (0x000000400000) , Counter: 0 , Response: Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x00 , Device not boot enabled
Boot Bus Config: 0x00 , x1 (sdr) or x4 (ddr) bus width in boot operation mode
H/W Reset Function [RST_N_FUNCTION]: 0x00 , RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition settings [PARTITION_SETTING_COMPLETED]: 0x00
EMMC Init completed
Backup saved: M72808_15000093_20220611_141710.extcsd (new backup)
Connected successfully
Operation: Scan PartitionTable from Source (Vendor: Binary Read/Write)
Scanning soft partitions from ROM2
GPT header is not found
Scanning soft partitions from ROM3
GPT header is not found
Scanning soft partitions from ROM1
GPT header is not found
MBR header is not found
You need a usb to uart device to get started on that board. You can find one online for about 3 dollars.