i tried to reinstall a new rom on my htc vox. i've done all things right, USPL 1.16, phone entered bootloader. then i tried to install the new rom and at 3% i recieved the following message: flash error.
i tried with a couple of roms, same thing. why did that happen? then i tried to reinstall an official rom, didnt work, SPL changed to 1.34, and phone went to service, new mainboard, back to orange rom.
so, why did i recieve that message? i dont want to repeat the procces without finding the reasons why it didnt work.
sorry for bad english
Related
I tried flashing my device from WM6 Titanium2 to the 2.26 t-mobile official rom so that I could flash with a new rom, i'm trying to aim for the new TNT rom, any idea why i cant downgrade to an official? it says my rom version is 10.1.0.811 wwe, such a low number? any ideas on how to make this work? it went to recovery mode with the update util but it still recovered fine to my old OS, didnt go right to the colorful bootloader.
[edit] i turned my device off, held camera button and turned it on to bootloader mode, and ran the RUU and it worked, weird.. still curious as to why it wouldnt work the other way.
well i had the same issue once.
It was very strange but at the end it worked.
Was installing duttys rom when my anti-virus program started. Update failed and since then all I see is the tri-colour screen. Sometimes I can get the rom updater to recognise my TyTNII but it will not continue to upgrade. Any suggestions. Have tried mtty1.42 but it doesn't seem to have a usb port option, have tried hard reset etc with no luck. Any suggestions would be greatly appreciated.
An update, I have tried several rom updates since, most get to the stage where the progress bar is shown and the stop. The HTC update to revert to shipped rom gets to 1% and then tells me that this rom is not suitable for my pda!
How about some more information...
What is your Tytn II - Tilt or HTC?
What Rom was on it before you tried upgrading?
What Radio was on it before you tried upgrading?
What version of Duttys did you try to flash?
Did you upgrade to HardSPL before you tried flashing?
This should enable someone to begin trying to unbrick your phone.
Also DO NOT USE MTTY unless you know what you are doing - it can seriously kill your Tytn if used incorrectly. Wait for GSLEON3 to swing by before trying this - but he's very busy at the moment helping others unbrick their toys so you may have to wait for a while.
If you had an original rom/radio from AT&T or HTC it shouldn't hurt trying to download an original rom and try to flash - preferably using your SD card.
Also, while you're waiting for someone to help, have a good read through the Kaiser Wiki (in my signature) before trying anything else.
what are the steps that u take? let us know if u are missing any
HTC TyTN 11, Was using Q-mobile 1.2 but couldn't install tom tom navigator 6, don't know what radio it was using because i hadn't got that far. Was trying to flash Dutty's 6.1 and I had run jumpspl from device because I got the white screen when I treid to run 1.93 so installed 1.56 to pda and ran it. this worked to insatll Q-mobile this morning.
Hope this helps!
what are the steps that u take? let us know if u are missing any
Try to reset pda keep getting tri-colour, attach usb and usb shows at base of screen. When i try to install rom The problem in my second post occurs. I cannot hard reset device to anything other than the tri-colour
Thanks for your help, I tried one of the roms indicated and it worked! I have spent so much time reading various wikis and downloading files. I'm not entirely sure why it worked this time but I'm not about to ask questions! Thanks again!
OK, now you've got your phone working again, make sure that you get HardSPL installed before you try anymore flashing.
ok i was installing KAIS_Radinly_0.26.07.06_CustomRUU and it froze at 96% and now my phone is bricked!! every time i restart the phone its stuck at the RED GREEN BLUE and WHITE screen.. i tried using mtty but then im not trying to mess my phone up any more. i dont understand how to fix it.. if i download a new ROM and put it on my SD card then how do i read it with my phone? sorry guys, im a noob at this as you can tell..
nm guys. i just ran the new rom and it worked! haha sorry for posting too quick!
okay i have one problem after fixing it. i downloaded the TEST rom for the ATT tilt and now every time i reboot my phone it says 'TEST ONLY. NOT FOR SALE.' how do i get rid of this? when i installed a new rom it still says this and i even tried hard resetting my phone but it did not reset anything to factory settings. it just reloaded the rom that i last had!
xmooglex said:
okay i have one problem after fixing it. i downloaded the TEST rom for the ATT tilt and now every time i reboot my phone it says 'TEST ONLY. NOT FOR SALE.' how do i get rid of this? when i installed a new rom it still says this and i even tried hard resetting my phone but it did not reset anything to factory settings. it just reloaded the rom that i last had!
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=KaiserFAQ
your answer is in there
Current Setup :
HardSPL (latest, 3.56 I believe)
Radio: 1.65.29.22 (from Niki or Neon, almost positive it was Niki)
Solace v3.1
Decided I wanted to go back to newest radio, attempted to flash to it; hit a snag at about 78%. Progress didn't update for a while, then to 100%. Update app said there was a flash error, and it did not complete correctly. Device restarted, stuck at bootloader. Re-attempted the flash, same result.
Next, I tried flashing AT&T's latest ROM. Stalled at about 76%, message about having a communication error, walked through the apps troubleshooting steps; it tried (and failed) again.
Tried the latest HTC direct ROM, same result.
Tried to flash the latest HTC via MicroSD card, got 20(ish) percent through, the Radio line then went red and said "RSA Failure". Then that whole process died on me as well.
The only way I can get my device back up to run MTTY to remove the RUU flag. When issuing the "task 8" command to format, it instead reboots the phone. The phone will come up normally after that.
Since I got it back up, I have tried flashing once again, and am getting the same result. Am I just stuck here now?
It's not that I don't like this ROM, I'm just wanting to update the radio. Any ideas what else I might be able to try?
Try using the search function next time before you create a new thread.
If you would tryed you could find this post
Yes, thank you...except that I started my thread saying that the proposed solution was exactly what CAUSED the problem to begin with. I tried to flash to the 1.70.x radio, which is where I got the flash write error.
Anyone else?
Now that you can get it up normally, have you tried going to a stock HTC ROM first, then the new ROM, then the radio? Or HTC, radio, new ROM? I'd probably do it the second way. You said you tried flashing stock before getting it up again, and that you tried flashing after getting it back up, but you didn't state what you've tried flashing after getting it back up.
Since I've gotten it back up, I've tried both OEM and radio only. Both have the same result.
Really at a loss now as to what to try next.
Did you try the 3.29Hard2 SPL? I haven't encountered your issue and wish I could be mroe help here. My only thoughts would be to try a different SPL, or perhaps looking into the ForceUSB issue. Best of luck.
Hey Guys,
First off this is a re-post, me old thread was closed, I am sorry for reopening but I am still having this issue. DaveShaw and smokestack76 had posted. Dave thank you for your reply but I have been through the noob flash guide and many many many other threads and it does not resolve my issue.
I'm not new to flashing and roms, I have flashed at least 100 times and have done some cooking. Had the random stuck in bootloader that wouldn't resolve itself today (using 3.29) Loaded kaisdiagsd.nbh and flashed stock att rom. (probably should have gone right for the spl patch but I was frustrated and needed my phone) Boot loader is now v3.65
Flashed fine, reboot, same issue. Phone will now only load the stock 6.1 att rom from the micro sd. kaisdiagsd.nbh is stuck on loading as for all other roms. I can occassionally get the os to load using mtty. From there tried jumpspl and it would not connect via usb at all.
I have tried flashing spl from the sd and yes spl image was KAISIMG.nbh and KAISDIAG.nbh was on there as well. Card is formatted fat32. HardSPL would start, read the file and get stuck on loading.
When in the stock 6.1 os I get the old unrecognized usb device in both xp and vista.
Is there anything else I can do to reflash spl? All i can think of is trying the task 2a, wiping everything and trying to flash from diag but I don't even want to try that route without something solid in place.
The phone is 2 years old, upgrading when the touch pro 2 hits att in aug sept or whenever it is released, but I need my phone.
I have gone through many many many posts. I'm stuck. Any help would be appreciated.
I have the stock 6.1 att rom up right now but I would like to resolve the issue.
__________________
finally finally got the patched version of 3.29 flashed. I will let you guys know how it goes from here. I am on a different computer at work.
Success!
I started from complete scratch and a fresh brain and was able to get everything going.
After I got the os back up i was able to start jumpspl and get it to connect via usb. Then only the force usb on 3.29 patch would work. After that repaired active sync and I was ready to go. Thanks smokestack79 for the late night help last night. I was out of it and frustrated. Seems like she's got a little more life in her after all.
I have an Qtek S100 and according to the imei check its an o2 rom.
After a long time i decided to use my qtek again just for fun and see what i can do with it.
In windows 2003se it keeps giving low battery although its connected to usb, anyway i decided to give it a go and installed wwe05 but totally forgot about the radio rom that needed to be 1.12. (it was 1.13).
So it gave "bad radio" during startup.
I tried to flash it with multiple radio roms, including the original o2 one, but some dont start at all and some keep getting stuck at 45%.
and eventually give error 114, i can flash it back to original rom, but as soon as i want to update the radio, same thing happens.
now it gives "no radio" in wwe05, and after flashing back to 2003se it says "no gsm".
the radio wasn't giving any error/problem before i decided to update the os, so i doubt it's an hardware issue. i checked mutiple threads about 114 radio, but haven't found a sollution yet.
maybe somebody here can help me get my radio back.
You should read this Thread first http://forum.xda-developers.com/showthread.php?t=705702. Maybe there is the Solution.
i tried them all with normal usb flash, they all stop at 45% and give error 114.
Next Idea is here : http://forum.xda-developers.com/showthread.php?t=494635&page=2
Dont use a USB HUb !
k, i charged battery as long as possible, (althought i think its nearly dead) it now shows 100%.
I'm also using a different system now with windows 7,, when trying to flash it doesn't give an error, but after a few seconds its shows "congratulations", but it hasn't done a thing....
i can only try a windows xp in vmware, will try next first.
nvm, tried multiple roms, guess one of them changed my bl, cause its showed version 1.5.0 when its needs to be 1.00 or 1.02, so i tried to update my bootloader with pnewbootloader and version 1.02.nb0 and it resulted in an error ITFlashRom and never came back to the living. no boot no bootloader. paperweight is going in the bin. topic can be closed.