I know there are a few threads on the battery levels being a bit random at times, but mine is really hacking me off.
It will stop at say 75% and just stay there, when I reboot its down to like 50% or less. Twice now its gone dead because I though it had plenty of charge but just wasn't moving.
Is it the phone or battery thats the problem or drivers or something - ps this is on a standard rom, no tweaks etc.
same here.im using romeos rom but it seems to be a problem with another roms to.the battery % stay (for example) 10 hrs 68 % and after reset dropt 5,10,15 % down . is it hardware problem or software ?
And quite same here... The case is a bit worse even. When I charge it from lo-bat warning to full, it sort of overcharges itself and might hang up even! I noticed this in two phases - 1) when I left my TP to charge during night, it was hanged in the morning 2) when charging from lo-batt and restarting at ~85% bat level, after boot up the battery reports something at 98% or something!
I have the same (all posts) some time I have 78% and make reset and now i have 89%. Which is real 78 or 89%!??
when I charge all night I have only 70-92% after 6 hours, and after reset 100%
For me this is unusable as I cant trust it without constantly rebooting which is not good enough.
Lucky for me its a second phone, so I'll flog it and think of something else.
Hi there!
I have the same problem, after charging over night. The battery indicator shows, that a battery is not fully charged. After short removing battery and rebooting it shows 100%. With another HTC battery it is the same. When I use another spare battery (not original HTC), it works correctly. But I dont like the spare battery, because it is hard to remove from device because of its sharp edges. I think, it is a HW problem of battery, or a problem of device.
Related
Maybe this depends on the batterys but mine was having that problem of going dead at higher and higher % it started at 10 than 30 then 50 and up to 70 I think.
I've tested all the solutions in the wiki (yes the freezer too ) but with no improvements, then I did the opposite, instead of draining the battery fast I drained the battery slowly and when the Universal shuted off I pluged it to the electricity until it boots ok and the cpu returned to 0/1%, then take it from electric power again and wait until it goes dead again and did this over and over again until I reached the minimum battery of 9% i think. Great improvement since I was already looking for battery replacements... Then I charged it over night.
Conclusion I have the Universal alive for 3 consecutive days (and nights) now at 52% waiting to check when it dies again
By draining the battery slowly I mean no light in the screen, no running programs and universal in closed state, flight mode and just one thing to check if it was alive or not, play some music in WMP in repeat mode, when it stoped playing it was time to have a litte more eletric juice until I could boot it up and start the music playing again.
When I have the final results -> when the universal goes down I will post the solution in the wiki
Again this may depend on the batterys but since there are so many people buying new ones you maybe want to try this solution too.
Oh and by the way I solved an "other" problem while trying to solve this...
Besides the tests on the battery like freezing it over night, taking the power level pin etc, I've started to think it was a problem from the rom so I cleaned the Universal doing that "task 28" thing and the result was solving the problem that I was having with the battery status (now home screen plus plus) it was not getting the cpu using percentage when in the past it did. Now with the cleaning reg whatever It is showing again the cpu using %
I don't know if you use this but it has a cool functionality, posting the cpu using % at the top bar of your universal can tell you how much the universal is working all the time, enabling you to notice when it is working when it shouldn't, normally some stupid background program that didn't go off...
hi there. I have two same unis, and three batteries. two standard, one big capacity 3200mAh (personally I dont believe it have such capacity, it is some china crap). but all three had that issue (uni shut down when capacity still showing more as 30% or more %). tried to deplete the battery completely (when it wont boot, I put device to bootloader mode and wait untill died completelly). now it show again 0% on all three batteries. I dont want to say, that your method is bad . no, I am just a lucky one, where the "wiki" methods worked correctly. and I think it is also important sometime charge the battery completelly, not only for couple of minutes, but until you see green light. when you deplete the battery completelly to zero (it is never zero, electronics integrated on the batter doesnt allow that) charging to full take much more time as before.
powerdetect
one more thing, you can test, how much capacity your battery have. it is simple utility called power detect. you can find it in THIS thread or as attached file. just copy to device and run. the test will suspend itself after one hour, so set all settings as needed. it will automatically create file, where you can find all important information. before you use it first time, charge your battery to full.
Thank you for the reply, My battery still dies at 30% but no more at 70% and 50% and it lasts 3 days/nights in a row.
I tried the boot loader mode but it seemed it had a timeout, instead of dying from battery losse it died from some kind of time out :/ because I was still capable of juicing some more battery if i went again to boot loader...
I will check that app, thnks again
wat i did..
well my battery used to shut off at 95 above present...wat i did was drain the battery with a 12 volt motor, took me a complete day for it to discharge, then i put it in the freezer, was suppose to put it for one night but i actually forgot bout me putting the battery in the freezer n i remembered after 2 days. then i charged it which also took around 18 hours to charge now my batter shouts itself at 70% n i can listen to music for 1.5 hours. which is a lot from a battery which was shutting at 95%
In the Raphael Radio thread(http://forum.xda-developers.com/showthread.php?t=439566), someone said:
Antzor said:
Try soft resetting the device and see if the charge holds.
I was impressed mine was only down to 50% by the end of the day, but then i did a soft reset and afterwards it read as 28%
Click to expand...
Click to collapse
I also have this kind of problem on my device, but not it doesn't occur every time on these situations. In further research, I find out only some of the batteries (I have 3 original batteries for the device) can't read accurately. Does anybody else experience this problem?
I also have this problem.
HTC support seem a bit oblivious to it however and gave me no help.
seems that after a few reboots, once the loss of charge seems to settle, ie only going down by say a few percent each boot, then it is stable, and once given a full to 100% charge, which can take more than overnight (if you leave the phone on - which it seems you have to, for this to work) then it holds a charge well.
Yep, same problem here as well. It seems to have started with me over-loading the battery. Afterwards it showed a bit of variation before and after a cold boot. However the differences are not that extreme (+- 5%). Also I noticed that temperature plays quite an important role.
Maybe also the battery % tweak has something to do with it, but I cannot confirm this.
Jouke74 said:
Maybe also the battery % tweak has something to do with it, but I cannot confirm this.
Click to expand...
Click to collapse
I've also noticed this. But I think that the battery reading is never fully accurate and never was on earlier devices either. It's only the detailed percentage reading which is now possible on the VGA screen that makes us noticing it.
DeepThought said:
I've also noticed this. But I think that the battery reading is never fully accurate and never was on earlier devices either. It's only the detailed percentage reading which is now possible on the VGA screen that makes us noticing it.
Click to expand...
Click to collapse
I always use other utilities to view battery status in percentage for years. On my previous devices, from Magician to Kaiser, percentage was going down all the time, but on Raphael, sometimes the percentage just freeze - It means, the percentage stayed on like 73% for serveral hours but after I soft-reset the device, the percentage reads 49%. So this problem is more than inaccuracy, actually it may be a hardware bug.
I've noticed that after charging my TP for around 2-3 hours the battery will be fully recharged, even though my TP is reporting it only being as low as 50 % charged. If I just unplug it at this point, and start using it normally, the battery reading is highly inaccurate and often freezes for several hours just to take a ~20 % dive later. However, if I do a soft reset after charging (no matter if it's fully charged or not) I feel I can get fairly accurate and consistent battery readings. Also, if I've been charging for ~3 hours, the battery reading may well say it's only 80 % charged, but after a soft reset it's gone up to 100 %.
So, for me, a soft reset after every charging period keeps the battery reading quite accurate.
I've been noticing the same problem with the soft resets from all my ROM flashing. I've also noticed that it pccurs sometimes when texting or using the internet. I'll send like one or two texts and my charge drops 5%. I guess the thing that calculates the battery charge uses some weird algorithm that doesnt work correctly when the phone is essentially idle.
My original device always seems to take forever to go below 100%, and I just got a new device that has the opposite issue - it never goes above 94%. So I did some further tests, tonight.
My 94% device goes down fairly steadily once unplugged. But, the device at 100% does not. Also, when the 100% device is drained and I recharge it, it still says it's charging when its at 100% - so what does this mean?
I think that the battery calibration is off, as we already assumed. So, my 94% device is really 100% and I suspect that it would survive beyond 0% as it probably still has 6% juice left in reality. And, in the case of the 100% device, it's probably mis-calibrated to 105 or 110% (or more?). Since the UI can't show you 105%, it just shows the max of 100% until it goes below 100% which can take some time. I also suspect that the device would cut out at 5% or 10% since it's actually drained completely.
So that's the reason, I think. As to the fix, I don't know. What's weird is that these two devices are so different in terms of how the battery status is calibrated.
How can this be fixed? Or "Recalibrated?
I'm letting one of them completely drain, to see what happens.
At least the 94% one gives me an idea on what the battery life is, since I can just tack on +6%. But the one stuck at 100% is a complete mystery - it could be 5% off, 10% or even more.
Also, these run on 2 cell batteries making 7.4V nominal. All the devices before are using single cell batteries at 3.7V nominal. So Android may have issues with that voltage difference.
roebeet said:
I'm letting one of them completely drain, to see what happens.
At least the 94% one gives me an idea on what the battery life is, since I can just tack on +6%. But the one stuck at 100% is a complete mystery - it could be 5% off, 10% or even more.
Click to expand...
Click to collapse
I had the 100% battery issue before and it took a long time for it to dip below 100% (so long that it seemed unreal). Later I decided to let it drain to zero before recharging it to full again. Since then the battery indicator seemed to behave normally and discharged at a normal rate when the tablet was in use.
Have you tried deleting /data/system/batterystats.bin to wipe battery status? Mine sits on 100% for ages so I'm trying this now.
roebeet said:
My original device always seems to take forever to go below 100%, and I just got a new device that has the opposite issue - it never goes above 94%. So I did some further tests, tonight.
My 94% device goes down fairly steadily once unplugged. But, the device at 100% does not. Also, when the 100% device is drained and I recharge it, it still says it's charging when its at 100% - so what does this mean?
I think that the battery calibration is off, as we already assumed. So, my 94% device is really 100% and I suspect that it would survive beyond 0% as it probably still has 6% juice left in reality. And, in the case of the 100% device, it's probably mis-calibrated to 105 or 110% (or more?). Since the UI can't show you 105%, it just shows the max of 100% until it goes below 100% which can take some time. I also suspect that the device would cut out at 5% or 10% since it's actually drained completely.
So that's the reason, I think. As to the fix, I don't know. What's weird is that these two devices are so different in terms of how the battery status is calibrated.
Click to expand...
Click to collapse
samepic said:
I had the 100% battery issue before and it took a long time for it to dip below 100% (so long that it seemed unreal). Later I decided to let it drain to zero before recharging it to full again. Since then the battery indicator seemed to behave normally and discharged at a normal rate when the tablet was in use.
Click to expand...
Click to collapse
I tried that once, by setting it to never shutoff and letting it go over night. The next morning I charged it to green plus 30m as someone suggested in the TnTL thread, but I still had the problem of the meter sticking at 100% for a long time.
Anyways, I installed 3.0.0(TnTL) on monday and decided to also use the CWM clear battery data option, and now it seems to be dropping more as expected, but I'm not entirely sure that I did it completely correctly as by the time that I did the clear battery data option it would've been below 100% charge since I did so AFTER running the update.zip... just have to wait and see now...
Battery Stays at 100% For Ages
My battery stayed at 100% for ages the first time I charged it. Then it dropped quickly and cut out around 50%. I recharged it and it seems to be behaving more normally now. It still seemed to hang at 100% for a while, but no where near as long as the first time. I'm waiting to see at what percentage it dies this time.
my zt 180 tablet never got above 94% also. And it dropped pretty quickly and at around 40% it seemed to get a second life and slow down, but eventually it went all the way down to about 10% and then I would charge it (about 3 hours max). It too is a 7.4v supply.
My Odroid T had a 3.4 supply and it was pretty linear, showed charged at 100% and went down accordingly, though the developers had some issues with a few software releases where it did behave erraticaly and they did a few patches that fixed it.
roebeet said:
My original device always seems to take forever to go below 100%, and I just got a new device that has the opposite issue - it never goes above 94%. So I did some further tests, tonight.
My 94% device goes down fairly steadily once unplugged. But, the device at 100% does not. Also, when the 100% device is drained and I recharge it, it still says it's charging when its at 100% - so what does this mean?
I think that the battery calibration is off, as we already assumed. So, my 94% device is really 100% and I suspect that it would survive beyond 0% as it probably still has 6% juice left in reality. And, in the case of the 100% device, it's probably mis-calibrated to 105 or 110% (or more?). Since the UI can't show you 105%, it just shows the max of 100% until it goes below 100% which can take some time. I also suspect that the device would cut out at 5% or 10% since it's actually drained completely.
So that's the reason, I think. As to the fix, I don't know. What's weird is that these two devices are so different in terms of how the battery status is calibrated.
Click to expand...
Click to collapse
Warning: Slightly off topic -
I'm glad Roebeet was able to get a 2nd Gtab. Hope you found a good discount. Happy Holidays!!!
Now back to the topic discussion...
Butch1326 said:
Warning: Slightly off topic -
I'm glad Roebeet was able to get a 2nd Gtab. Hope you found a good discount. Happy Holidays!!!
Now back to the topic discussion...
Click to expand...
Click to collapse
Off-Topic x2 : yep, got used one that another XDA user had returned!
On-Topic: Still waiting for the battery to discharge, it went to sleep last night. Getting close....
roebeet said:
Off-Topic x2 : yep, got used one that another XDA user had returned!
On-Topic: Still waiting for the battery to discharge, it went to sleep last night. Getting close....
Click to expand...
Click to collapse
I also had the issue of battery showing 100% for a long time and then cutting out around at 50%. One of the posts mentioned doing a battery stat wipe in CWM after charging to 100% + 30 minutes.
I did this with a little twist of my own.
I allowed the battery to drain completely and tab to shut off. Plugged in the charger and immediately did a battery wipe in CWM. Allowed the battery to charge fully upto 100% + let it be on charger for additional time till the battery symbol in the notification bar no more showed charging sign. Again did the battery stat wipe in CWM and then rebooted the tab.
Since then i observe that the battery has been draining as it should be expected to. down to 72% after about 4+ hours of use. I will still be monitoring the battery discharge further for two or three more charge cycles. But I feel doing battery stat wipe in cwm 2 times at full drain and then again at full charge might have helped caliberate it properly.
Let me know if anyone else tries this and gets same or different observations.
Try installing this to measure your current usage over the life of the battery... (dont have a GTab and still considering). Since most likely this widget and the battery monitor are using the same API we will see if its a hardware sensor issue or a software issue...
http://www.appbrain.com/app/currentwidget/com.manor.currentwidget
I suspect its in their battery monitor and not the sensor or API... if that is the case it should be easy to debug (if you have the source). Typically these issues are due to poor polling algorithms...
Im new to android so I am unfamiliar with profiling capabilities of the platform...(Still learning)
Perhaps this will be one of the 'little fixes' that will be present in the latest FW update when VS drops it tomorrow. I have the 100% unit BTW. A fix would be nice.
Reading this thread this morning it got me thinking about my gtab battery situation. When I first got the gtab, the battery stayed at 100% for hours, then the percentage dropped like a rock. Over time, the battery dropped in more regularly, although it drops in large numbers (like from 100% to 83%, then to 67%, and so on). I'm currently running TnT Lite 3.0.
This morning I charged the battery to 100%, and while plugged in (to the AC outlet), I reset the battery stats using cwm. The battery today has been steadily going down throughout the day as I would expect. In over 8 hours, I watched the battery go down steadily from 100% to 84%. So far, so good.
my exp
Tried draining once, just let it sit, didn't fix it.
Tried again but this time I kept the screen on and watched the voltage, shutdown was near 6.8 volts. Now the meter is accurate. YMMV...
@it'sDon - it wasn't fixed in the update.
I was in the same boat as most of you. Took a very long time to go down from 100% and then zonked out completely at ~10-15%. It's now been charging for a few hours and it's been sitting at 100% for quite a while but the light is still red (so it's still charging) which means it will probably happen again looks like it's charging to some value over 100% and when it discharges, knocks out while the meter is still reading as having juice. Roebeet is 100% on the money.
I am going to try the CWM battery value reset some of you mentioned to see if it does something once my light is green, then I won't charge it and watch it like a hawk once it hits 20% to see if it shuts down at 10-15% or a value less than 3% which is acceptable I think.
I never had a problem on my stock(ish) g-tablet. That is until I installed the latest update.
I had to do a data wipe before any of the cosmetic TnT changes would show. After that the battery now seems stuck at 100%. This wasn't that way before, so I will try draining the battery, and see what happens.
Since I found that this was tied to my latest update, I think that I should call CS and complain.
My battery drain didn't make a difference, either. Still haven't pinned down a fix that works.
At least those of you with 94% max have a general idea when your battery will die. With us "100% forever" ones, we have no clue.
Actually, I may not have a problem after all. I have had my tablet on for about two hours. It is now showing the battery at 86%.
Well Im not saying the battery life itself is bad, but well for example, I just drained the battery completely (phone shut down by itself) and within about 2 minutes of putting the charger back in the indicator read 70%.
Im currently using the method where i run it down to 1% then fully charge, rinse and repeat. (Just started doing this)
Just thought I would share
sambaman009 said:
Well Im not saying the battery life itself is bad, but well for example, I just drained the battery completely (phone shut down by itself) and within about 2 minutes of putting the charger back in the indicator read 70%.
Im currently using the method where i run it down to 1% then fully charge, rinse and repeat. (Just started doing this)
Just thought I would share
Click to expand...
Click to collapse
no problems here, but apparently half the people in the battery threads have issues with battery life.
hmmm, well I just want to get this right because it gets annoying when it says 100% battery then goes down in about 20 minutes
I've had issues with battery life indication on my Omnia 7.
I can have it showing 70%, then it would suddenly drop to showing around 10%. Then by turning off and on several times it will sort itself out and show the correct amount.
This has only happened once or twice mind...
No problem here on my HTC 7 pro. Though I did calibrate one battery and not the spare, both perform the same.
I have no problems either on my omnia 7
follow this::
http://forum.xda-developers.com/showthread.php?p=15338429#
No issues on my Focus. Maybe this is a device specific issue?
sambaman009 said:
Well Im not saying the battery life itself is bad, but well for example, I just drained the battery completely (phone shut down by itself) and within about 2 minutes of putting the charger back in the indicator read 70%.
Im currently using the method where i run it down to 1% then fully charge, rinse and repeat. (Just started doing this)
Just thought I would share
Click to expand...
Click to collapse
No problem with my trophy but a good practice to keep you battery in shape is to start charge at 15-20% (dont leave it until is dead is bad for the battery) and dont charge it to 100% ...stop charging at 90-95% ...
That is what i do with all my mobile devices and rarely i have probs with my batterys.
Hi everyone
My problem is.. my DS started to charge slowly.
Now it doesn't really charge slowly, If I check the voltage, I will get like 4220mv but as soon as it reaches that, the charging graph just goes flat.
If say I have charged it to 70% and it started going slow. i switch it off, place on the charger, and the lamp goes green. I turn it on, and it is showing 100%.
I have tried calibrations, diffirent kernels, wiping, factory resets e.t.c.
Another thing is that if I will run a v6 battery calibrator,it will show that actually I should have a 100% charge although a phone is showing only 70%.
So the summary: Phone charges normally when off (when recovery monitors charging), showing the correct voltage when on... But showing the wrong percentage if on charge.
Also sometimes if the battery is like 14% left. And I turn the phone off and then on again, it will show 22% bearing the same voltage as when it was 14%.
Question: Is there any way to tweak the battery indicator so it would show % values same as the v6 calibrator does it or is it a hardware fault, if yes, which part of it ?
This happens to me on my older (original) battery, but not my new one. I bought the second battery when this problem started happening. So, I think it's just a symptom of an old battery.
By the way, if you leave it on charge long enough, it will eventually jump up to 100%.
Other than this weird behaviour, it has no real impact on anything.
Sent from my Nexus 7
Thought so, mines been acting similarly lately, but strangely enough it seems to be getting better
I think I found out..
I actually purchased a new battery recently, because my old one was jumping like crazy and started discharging in a few hours..
This new battery I bought from a mobile repair shop.
It is a cheap chinese battery with no name, anyhow I just took it out to take a look at it...
And guess what, it sais 1200mah..
Can the phone be confused because of that ?