Related
I've found a way to register the G1 in the initial registration screen that comes up the first time you boot the phone (or after you wipe the phone). It will allow you to register if you don't have a sim card at all, or if you have a sim card but no data plan.
First, You must have either RC29 or earlier, or modded RC30. It won't work with official RC30, sorry. If you don't know for sure what version you have, but you know you haven't installed a modified RC30 build, then the easiest way to check is to reboot the phone, and once it starts up and is showing the "click the android to begin" screen, or the "no sim card" screen, then type the following on the phone keyboard
<enter>reboot<enter>
If it reboots, then you have RC29 or ealier. Otherwise you have RC30.
Second, you must have adb installed on your computer, and have the USB drivers installed, or at least ready to install when it asks for the driver when you connect the G1. See this page for details on how to get adb working: http://code.google.com/android/intro/develop-and-debug.html#developingondevicehardware
Third, you must have a wifi network that you can connect to.
There are too many possibilities to write specific step-by-step instructions for every case. So I will give an overview of the process instead. If someone else wants to write some specific instructions, that would be welcome
-----------
When you start up the phone without a sim card, it goes into a locked screen that says "no sim card found", and you can't even get into the registration app. So the first step is to get around that screen. You have to connect to your phone with adb shell and get root access, and then type the following command:
sqlite3 /data/data/com.android.providers.settings/databases/settings.db "INSERT INTO system (name, value) VALUES ('device_provisioned', 1);"
And then reboot the phone. When it starts up again it will go into the registration screen instead of the locked "no sim card" screen.
This assumes that you have the sqlite3 binary on your phone. This binary is provided in RC30 v1.2. Alternatively, you could manually copy the binary to your phone with adb push, or put it on the sdcard and copy it to your phone. I can post a copy of just the sqlite3 binary if needed.
-----------
The second step is to enable and configure wifi, so that the registration process can connect to the google servers. In an adb shell session, type the following command:
am start -a android.intent.action.MAIN -n com.android.settings/.Settings
This doesn't have to have root access to work. It works fine with the "shell" user that adb on non-modded phones runs as.
That command will bring up the settings page on your phone. From there, you can enable wifi and connect to your wifi network, and then proceed with registration as per normal
------------
A few tips and tricks:
- If you have an official RC29 or lower phone, type the following command on the phone keyboard to enable adb:
<enter>setprop persist.service.adb.enable 1<enter>
- If you need to get root access on an official RC29 or lower phone, while it's at the registration screen, or the "no sim card" screen, enable adb (see first tip), and then type the following command on the phone keyboard:
<enter>telnetd<enter>
Now, copy a busybox binary to /data/local/busybox with adb push, and then connect to your phone with adb shell, and give the busybox binary execute permissions (i.e. chmod 755 /data/local/busybox)
busybox has a telnet applet, so you can do:
busybox telnet 127.0.0.1
to get a telnet session with root access.
- If you don't want to register the phone at all, you can set the app.setupwizard.disable property to 0 to prevent registration. Once you have an adb shell session open, type the following:
setprop app.setupwizard.disable 1
and then reboot. once it loads back up, it should bypass the registration screen all-together.
But beware, the phone seems a bit glitchy if you don't have it registered. For example, the home button doesn't seem to work. And you can't access the market or any of the google apps of course.
(Note: the following was the previous way to skip registration. I'll keep it here for informational purposes, but its easier to use the app.setupwizard.disable method instead of this)
- If you don't want to register the phone at all, you can edit /data/system/packages.xml and disable the registration screen. Add the following to the end of the <package> section for com.android.setupwizard, and then reboot:
<disabled-components>
<item name="com.android.setupwizard.SetupWizardActivity" />
</disabled-components>
so the full <package> would look something like below after the modification:
<package name="com.android.setupwizard" codePath="/system/app/SetupWizard.apk" system="true" ts="1217592000000" userId="10010">
<sigs count="1">
<cert index="0" />
</sigs>
<disabled-components>
<item name="com.android.setupwizard.SetupWizardActivity" />
</disabled-components>
</package>
He worked on this for a very long time with me and walked me through all the steps when testing this out. Great person.
Really nice...
I'll try to do it.
I have to study though...
I'll be in touch.
Thanks
thanks JF you are good in this thing.
My case i have sim card without data plan, when turn on phone show me screen for register email account with google.
c:\adb shell
show me # simbol
am start -a android.intent.action.MAIN -n com.android.settings/.Settings
and in the phone show me the menu for connect to my wireless
conected, registered, go ahead.
thanks
satru, in what screen are you typing "c:\adb shell"?
1. Before you click "the android"
2. while reading the agreement
3. When you can select "create" or "sign in" to a google account
4. Or later ? (where?)
Thanks
EDIT:
Ok, I hate to do that but:
I am completely stupid. I've been reading around xda-dev for hours and still can't find how to check what software I'm running. (prior or post RC30...)
In boot loader it says:
"DREA100 PVT 32B
HBOOT-0.95.0000
CPLD-4
RADIO-1.22.12.28
Sep 2 2008
Serial0"
Do I have RC30?
I couldn't get it out of bootloader mode, so I pulled the battery out.
Ok, my device was recognised and "installed" but no driver was requested.
I have read I need to do some settings from within the g1, but I can't, since it's not activated! (http://forum.xda-developers.com/showthread.php?t=443797&highlight=info)
When I issue the "adb devices" command, I get no recognised devices...
To cmavr, try entering the restore mode and see if the computer will detect it then. Is it automatically mounting the SD card onto the computer? If it is then you probably have RC19 which is good. Try removing the SD card and plugging the phone into the computer.
cmavr8 said:
satru, in what screen are you typing "c:\adb shell"?
1. Before you click "the android"
2. while reading the agreement
3. When you can select "create" or "sign in" to a google account
4. Or later ? (where?)
Thanks
EDIT:
Ok, I hate to do that but:
I am completely stupid. I've been reading around xda-dev for hours and still can't find how to check what software I'm running. (prior or post RC30...)
In boot loader it says:
"DREA100 PVT 32B
HBOOT-0.95.0000
CPLD-4
RADIO-1.22.12.28
Sep 2 2008
Serial0"
Do I have RC30?
I couldn't get it out of bootloader mode, so I pulled the battery out.
Click to expand...
Click to collapse
A quick way to check if you have RC30 is to reboot the phone, and then once it starts up and it shows the "click the android to begin" screen, type
<enter>reboot<enter> on the phone keyboard.
If it reboots, you have RC29 or lower. Otherwise you have RC30.
If you do have RC29 or lower, then you can use the first tip I posted to enable adb. Once adb is enabled it should ask you to install the drivers when you plug it in.
satru said:
conected, registered, go ahead.
thanks
Click to expand...
Click to collapse
Great! Glad it worked for you
Hi again, thanks for your reply.
I rebooted without sim card, no "click here to begin" appeared, just the "no sim card" notice.
I entered reboot and it rebooted! So this is good.
Now, with the phone connected, I type in terminal:
"[email protected]:/media/Docs/Android/tools$ ./adb shell
error: device not found
[email protected]:/media/Docs/Android/tools$ ./adb devices
List of devices attached
[email protected]:/media/Docs/Android/tools$ "
This is not normal, is it?
What should I do now?
(I also have a t-mobile sim card, not activated. It just came with the phone. I can go through the activation proccess (gmail account etc) but it can't complete as it's disabled)
cmavr8 said:
Hi again, thanks for your reply.
I rebooted without sim card, no "click here to begin" appeared, just the "no sim card" notice.
I entered reboot and it rebooted! So this is good.
Now, with the phone connected, I type in terminal:
"[email protected]:/media/Docs/Android/tools$ ./adb shell
error: device not found
[email protected]:/media/Docs/Android/tools$ ./adb devices
List of devices attached
[email protected]:/media/Docs/Android/tools$ "
This is not normal, is it?
What should I do now?
(I also have a t-mobile sim card, not activated. It just came with the phone. I can go through the activation proccess (gmail account etc) but it can't complete as it's disabled)
Click to expand...
Click to collapse
Did you try my first tip to enable adb?
johnny13oi said:
To cmavr, try entering the restore mode and see if the computer will detect it then. Is it automatically mounting the SD card onto the computer? If it is then you probably have RC19 which is good. Try removing the SD card and plugging the phone into the computer.
Click to expand...
Click to collapse
Thanks for your reply.
SD mounting works fine.
In recovery mode nothing is better... (tried recovery without sd only)
Is there anything else I should try?
JesusFreke said:
Did you try my first tip to enable adb?
Click to expand...
Click to collapse
What do you mean enable?
I should enable it on the g1 but it's locked, no menus available.
I thought the first step was to enter the "adb shell" command in the PC, then pass this through the pc to the G1:
"sqlite3 /data/data/com.android.providers.settings/settings.db INSERT INTO system (name, value) VALUES ('device_provisioned', 1);"
Am I missing something?
cmavr8 said:
What do you mean enable?
I should enable it on the g1 but it's locked, no menus available.
I thought the first step was to enter the "adb shell" command in the PC, then pass this through the pc to the G1:
"sqlite3 /data/data/com.android.providers.settings/settings.db INSERT INTO system (name, value) VALUES ('device_provisioned', 1);"
Am I missing something?
Click to expand...
Click to collapse
A couple of things:
- Look further down the post, there's a "tips and tricks" section. The first tip is how to enable adb.
- second, I don't think you need to go through the first step (the sqlite3 command). The first step is to get past the "no sim card" screen. You said you have a sim card, just no data plan, right? So you don't need to get past the "no sim card" screen . You can skip to the second step (once you get adb working, of course)
DID IT!
Thanks so much!!
I now have to wait for the unlock code so that I can also use my sim card...
Thanks both of you!
EDIT:
T-mobile sent me the unlock code although I was not a customer for even one day!
That's great...
Great! Glad you got it working
cmavr8 said:
EDIT:
T-mobile sent me the unlock code although I was not a customer for even one day!
That's great...
Click to expand...
Click to collapse
how?
thanks
xaxis said:
how?
thanks
Click to expand...
Click to collapse
Probably by getting lucky and getting a nice CSR
JesusFreke said:
Probably by getting lucky and getting a nice CSR
Click to expand...
Click to collapse
man thank god you are here,
do i need the SDK installed to get the adb?
thank you
Yes, adb is included in the sdk
So i read a story on Engadget that would allow the Nexus One to record videos in 720p. I wanted to do that but i was told that i had to modify my phone with some program called cyanogenmod. I was linked to this guide:
edit: well i'm not allowed to post links on this forum, that sucks. I'll just post a snippit of the webpage.
Prerequisites
In order to flash a fully stock Nexus One with any ROM, you must first unlock the bootloader of your Nexus One and flash a Recovery Image. If your Nexus One's bootloader is already unlocked, and you already have a Recovery Image installed, skip this section.
WARNING: UNLOCKING THE NEXUS ONE'S BOOTLOADER WILL VOID YOUR WARRANTY!
You will need the fastboot shell on your computer to use the commands to unlock the bootloader. Follow the Install the Latest Android sdk guide, to get the ADB and Fastboot shell on your computer.
Before continuing, you should first copy all the necessary files to your SD Card. Doing so will make the entire process much easier and faster. Please do the following to copy the files from your computer to SD card root if your Mass storage is not mounted or you get error when trying to access the mass storage drive.
Connect Nexus One to Computer
Make sure the computer picks up the newly connected device and shows a new mass storage drive
On the phone, pull down the top notification slider, you should see an item called "USB Connected"
Click on the "USB Connected" and click Mount. This will make the phone SD Card available for use with computer
Copy the required files
Files you will need:
Download the latest release of CyanogenMod for the Nexus One and the Google Addon from here Mirror1 Mirror2 Mirror3 Mirror4 Mirror5 Mirror6 Copy these two to your SD Card
Download the latest release of Amon_Ra's Nexus One Recovery Image from - Leave the recovery.img on your pc
Rename Amon_Ra's recovery file "Recovery.img", and make sure you have copied the above two zip files to the root of your SD Card.
Power off your phone.
Boot into Bootloader Mode.
Hold down the trackball, and press the power button. Do not let go of the trackball until the phone boots into bootloader mode (You will see a white screen with three skating bugdroids).
Unlock the Bootloader.
Make sure your phone is connected to your PC.
On your PC, navigate to the AndroidSDK\tools folder.
Hold down the Shift key, Right click on an empty space inside the folder, and press "Open command window here". (note: on Windows XP, this might not work. Instead, you may need to open the command window by going to Start - Run - Type "cmd" - press Enter, then type "cd c:\AndroidSDK\tools" (without the quotes), press Enter)
Inside the command prompt that opens up, type in the following command:
fastboot oem unlock
On your phone, a prompt will open up, asking you if you are sure you want to unlock your bootloader, and again warning you that doing so will void your warranty. If you agree to these terms, press Volume Up to select Yes, and then press the Power button to confirm.
Your phone will restart. Let the phone boot into Android. Switch the phone back to usb debugging (unlocking bootloader causes a wipe, reseting settings), and then Power Off the phone.
Once again, boot into bootloader mode.
Flash Recovery.
Note: The Recovery.img should NOT be on the SD Card, it should be in the current working directory.
On the command prompt you opened earlier, type in the following command:
fastboot flash recovery Recovery.img
The recovery image should now be installed on your Nexus One.
Click to expand...
Click to collapse
But i'm lost. I downloaded all the necessary files so far but i'm confused up to this point:
Boot into Bootloader Mode.
Hold down the trackball, and press the power button. Do not let go of the trackball until the phone boots into bootloader mode (You will see a white screen with three skating bugdroids).
Unlock the Bootloader.
Make sure your phone is connected to your PC.
On your PC, navigate to the AndroidSDK\tools folder.
Hold down the Shift key, Right click on an empty space inside the folder, and press "Open command window here". (note: on Windows XP, this might not work. Instead, you may need to open the command window by going to Start - Run - Type "cmd" - press Enter, then type "cd c:\AndroidSDK\tools" (without the quotes), press Enter)
Inside the command prompt that opens up, type in the following command:
Click to expand...
Click to collapse
I'm on a Mac so i dunno if that makes a difference to how i approach this. but when i power my phone down and boot it into bootloader mode, i can't access the phone on the computer because the phone isn't mounted, its at the white screen. how can i access this androidSDK/tools folder?
Credit goes to eugene373 and attn1. These are mostly their instructions, but I did change, clarify, and add a few steps. If you can't get any of the other methods working, try this one.
Prerequisites...
Note: If you're in Linux, you only need to do Step 4, Step 6, and Step 7.
Step 0.
Download and install HTC Sync: http://www.htc.com/us/support/aria-att/downloads/
Step 1.
Download and unzip the Android SDK: http://developer.android.com/sdk/index.html
Step 2.
Go into the folder where you unzipped the Android SDK and open "SDK Setup.exe".
If you aren't greeted with a failed to fetch URL error, proceed to Step 3. If you did receive this error, go to Settings in the "Choose Packages to Install" window and check "Force https;//... sources to be fetched using http://..."
Close and re-open "SDK Setup.exe".
Step 3.
When the "Choose Packages to Install" window pops up, make sure the package "Usb Driver package, revision x" is checked. You can uncheck everything else. Click Install. After it downloads and installs, close "Android SDK and AVD Manager".
Step 4.
With your device unplugged from your computer, go to Settings > Application > Development on your device and turn on USB Debugging.
Step 5.
Now plug your device in to your computer. This is just to make sure the USB drivers are installed.
Once they are installed, unplug your device and turn it off.
Step 6.
This step is optional, but it may prevent an error later on in the process. If you've never formatted your SD card from a computer, remove it from the phone and format it in Windows or OSX with an external card reader. Then place the formatted card back in your phone, but leave the phone off.
Step 7.
Download the updated Root.zip from eugene373's guide: Root the Slide & Other HTC Devices*6/15/2010* How-To Updated 6/29/2010
Now let's get started...
Step 0.
Unzip Root.zip
Step 1.
Place the contents ("update.zip", "ota.zip", and "loop") into the Android SDK tools folder.
Step 2.
Open Command Prompt or Terminal and CD to the SDK tools directory.
Step 3.
Power on your device into the bootloader by holding the "Volume Down" key and simultaneously pressing Power.
Once you're in the bootloader, wait about 30 seconds until some diagnostic checking is done.
Press "Volume Down" to highlight Recovery, but do not push Power to execute just yet.
Step 4.
Now run your loop file from the prompt (either type "loop" in Windows or "./loop.sh" in Linux) (refer to ice3186's post for Mac instructions)
Note: The loop does nothing but show you the connection status of your phone. It's not technically required, but we'll use it in this guide.
Step 5.
Once the loop is running in your prompt, get ready to connect the phone to the computer with the USB cable, but don't connect one end quite yet. With Recovery still highlighted on your phone, you will need to push the Power button and then immediately plug in the other end of the USB cord.
Step 6.
After a few seconds, you should see your device listed in the loop.
Step 7.
Unplug the USB cable from the bottom of your phone and plug it back in. You probably don't need to do this, but let's be safe. Wait for your device to show up in the loop again. Hit CTRL-C to terminate the loop.
Step 8.
You should see a triangle/exclaimation over a phone graphic.
Hold the "Volume Up" key (note it's Volume UP this time) and simultaneously press Power.
After the menu comes up, use the volume and power buttons to select and run update.zip. (This will fail, but we already know that! Select it anyway.)
Step 9.
Paste the following command into your prompt and press Enter.
adb push ota.zip /sdcard/update.zip (*OSX users add a ./ in front of all terminal commands please)
Step 10.
This is very important!! Have this next command ready in your prompt before running update.zip again!!
This is the command. Paste it into your prompt, but DO NOT press Enter yet.
adb push update.zip /sdcard
Step 11.
Run update.zip and as soon as you see a faint progress bar appear behind the text at the bottom of the screen, push Enter to execute the command in your prompt.
Step 12.
If successful, you should see Clockwork Recovery and you now have Su and Superuser.apk installed! You can now reboot your phone into the OS to verify. If unsuccessful, repeat steps 11 and 12.
Step 13.
This step is optional, but it will save you the pain of going through all of these steps again in the future.
Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!)
I think some trouble shooting comments should be mentioned, so I'll just write a few things I noticed while rooting my device (for 7 frustration filled hours).
If you cannot see your device show up in 'adb devices' in recovery, boot into the OS normally and see if it shows up. If it does not, then it's a safe bet that you have one of two problems - you do not have all the drivers installed, or you do not have 'usb debugging' enabled. This can be enabled in 'settings->applications->development->usb debugging'. To avoid driver issues, it's highly recommended that you do this process in linux or osx.
If, on the other hand, your phone DOES show up in Android but not in recovery, or if it just blips on the screen for a second (when running the loop) as an offline device, then it might be the formatting of your sd card. Do NOT format your sd card from your phone or within Android. The ONLY time I managed to get the phone to show up in recovery without disappearing immediately was by removing the sd card, formatting it in windows or osx with an external card reader, copying the files over (new rom or rooting files), and then replacing it in the phone while the phone is off. After putting the card back in your phone, try the procedure again - go to the bootloader->hboot->recovery (while the cable is unplugged), then press the power button and immediately after plug the cable in (usually works when you plug the cable in about .2-.5 seconds later). If it does not show up at all, reboot the phone and try again, but do NOT let it boot back to Android. You can get back in to the bootloader by waiting until the 'HTC quietly brilliant' screen shows up and typing 'adb reboot bootloader' with the usb cable attached.
It took me a really long time to figure that out. I don't think the type of sd card matters so much as the formatting of it. I actually used the 2gb card that came with the phone, and it worked almost every single time after I reformatted the card.
Also, if you manage to get it working and root the phone, do yourself a huge favor and install the custom Unrevoked recovery image mentioned in the original rooting thread, so you never have to deal with this nonsense ever again.
Also also, if you get to the step where you do 'adb push ota.zip /sdcard/update.zip' and you get an error:0, installation aborted message, you did something wrong. The problem is that you aren't actually supposed to flash ota.zip. What you're supposed to do is push ota.zip to your phone as update.zip, and leave it there. Don't touch anything else. What you will do after that is type 'adb push update.zip /sdcard/update.zip' in the command prompt (WITHOUT hitting enter yet, just get ready to). You will then select 'sdcard:update.zip' and press power and IMMEDIATELY AFTER pressing power, you will press enter on the command prompt to execute your adb push command. What this does is causes recovery to read the ota.zip file you uploaded and recognize it as a legit update, but you replace it with update.zip before it actually gets extracted (if your timing is good). So recovery reads the signature of ota.zip, but actually extracts the stuff in update.zip and runs that instead.
Hope that helps with some common problems I observed. Good luck, dudes.
okay so I think I the only one using a Mac in this rooting process. A few things I have learned and may already be known but I thought I would clarify.
1.) to get a loop to run on the mac i had to re-write the file loop.bat
this is the code that works for me and how to do it.
a.) rename the file to end in .sh not .bat the way it came
b.) open the file with TextEdit
c.) delete all of the text in it and write this in there
Code:
while [ "0" ]
do
{
./adb devices
}
done
d.) save the file back in the sdk/tools folder
e.) in terminal the command once you cd to the folder is ./loop.sh
2.) i have yet to be successful in the attempt to root so anyone knowing anything to help would be appreciated! But i am still cracking i think i am going to wear out the plug before i am done though.
it should be pointed out that the loop does nothing except tell you if you have a connection or not. When you plug in the usb port, it will respond after a few seconds, or it won't. Try again.
gtg465x said:
Credit goes to eugene373 and attn1. These are mostly their instructions, but I did change, clarify, and add a few steps. If you can't get any of the other methods working, try this one.
Prerequisites...
Step 0.
Download and install HTC Sync: http://www.htc.com/us/support/aria-att/downloads/
Step 1.
Download and unzip the Android SDK: http://developer.android.com/sdk/index.html
Step 2.
Go into the folder where you unzipped the Android SDK and open "SDK Setup.exe"
When the "Choose Packages to Install" window pops up, make sure the package "Usb Driver package, revision x" is checked. You can uncheck everything else. Click Install. After it downloads and installs, close "Android SDK and AVD Manager".
Step 3.
With your device unplugged from your computer, go to Settings > Application > Development on your device and turn on USB Debugging.
Step 4.
Now plug your device in to your computer. This is just to make sure the USB drivers are installed.
Once they are installed, unplug your device and turn it off.
Step 5.
Download Root.zip from eugene373's guide: http://forum.xda-developers.com/showpost.php?p=6820344&postcount=1
Now let's get into it...
Step 0.
Unzip Root.zip
Step 1.
Place the contents ("update.zip", "ota.zip", and "loop") into the Android SDK tools folder.
Step 2.
Open Command Prompt or Terminal and CD to the SDK tools directory.
Step 3.
Power on your device into the bootloader by holding down the "Volume Down" key and simultaneously pressing Power.
Once you're in the bootloader, wait about 30 seconds, until some diagnostic checking is done.
Press "Volume Down" to highlight Recovery, but do not push Power to execute just yet.
Step 4.
Now run your loop file from the prompt (either type "loop" in Windows or "./loop.sh" in a *nix like) ( ./ Is used For OSX )
Step 5.
Once the loop is running in your prompt, get ready to connect the phone to the computer with the USB cable, but don't connect one end quite yet. With Recovery still highlighted on your phone, you will need to push the Power button and then immediately plug in the other end of the USB cord.
Step 6.
After a few seconds, you should see your device listed in the loop.
Step 7.
Unplug your USB cable from the bottom of your phone and plug it back in. You probably don't need to do this, but let's be safe. Wait for your device to show up in the loop again. Hit CTRL-C to terminate the loop.
Step 8.
You should see a triangle/exclaimation over a phone graphic.
Hold down the "Volume Up" key (note it's Volume UP this time) and simultaneously press Power.
After the menu comes up, use the volume and power buttons to select and run update.zip. (This will fail, but we already know that! Select it anyway.)
Step 9.
Paste the following command into your prompt and press Enter.
adb push ota.zip /sdcard/update.zip (*OSX users add a ./ in front of all terminal commands please.)
Step 11.
This is very important!! Have this next command ready in your prompt before running update.zip again!!
This is the command. Paste it into your prompt, but DO NOT press Enter yet.
adb push update.zip /sdcard
step 12.
Run update.zip and as soon as you see a faint progress bar appear behind the text at the bottom of the screen, push Enter to execute the command in your prompt.
Step 13.
If successful, you should see Clockwork Recovery and you now have Su & Superuser.apk installed! You can now reboot your phone into the OS to verify.
If unsuccessful, repeat steps 11 & 12.
Click to expand...
Click to collapse
This isn't complete - this just gets you to clockwork and you haven't installed anything yet. You need to add steps to add root acces or flash a rom that is rooted. Also, make sure to reference the unrevoked tool to install Clockwork after root so this whole ordeal can be avoided next time.
Yes! The secret was formatting the sd card outside of the phone. I am now rooted and liberated! Thanks for plugging along with all the advice guys!
modest_mandroid said:
I think some trouble shooting comments should be mentioned, so I'll just write a few things I noticed while rooting my device (for 7 frustration filled hours).
If you cannot see your device show up in 'adb devices' in recovery, boot into the OS normally and see if it shows up. If it does not, then it's a safe bet that you have one of two problems - you do not have all the drivers installed, or you do not have 'usb debugging' enabled. This can be enabled in 'settings->applications->development->usb debugging'. To avoid driver issues, it's highly recommended that you do this process in linux or osx.
If, on the other hand, your phone DOES show up in Android but not in recovery, or if it just blips on the screen for a second (when running the loop) as an offline device, then it might be the formatting of your sd card. Do NOT format your sd card from your phone or within Android. The ONLY time I managed to get the phone to show up in recovery without disappearing immediately was by removing the sd card, formatting it in windows or osx with an external card reader, copying the files over (new rom or rooting files), and then replacing it in the phone while the phone is off. After putting the card back in your phone, try the procedure again - go to the bootloader->hboot->recovery (while the cable is unplugged), then press the power button and immediately after plug the cable in (usually works when you plug the cable in about .2-.5 seconds later). If it does not show up at all, reboot the phone and try again, but do NOT let it boot back to Android. You can get back in to the bootloader by waiting until the 'HTC quietly brilliant' screen shows up and typing 'adb reboot bootloader' with the usb cable attached.
It took me a really long time to figure that out. I don't think the type of sd card matters so much as the formatting of it. I actually used the 2gb card that came with the phone, and it worked almost every single time after I reformatted the card.
Also, if you manage to get it working and root the phone, do yourself a huge favor and install the custom Unrevoked recovery image mentioned in the original rooting thread, so you never have to deal with this nonsense ever again.
Also also, if you get to the step where you do 'adb push ota.zip /sdcard/update.zip' and you get an error:0, installation aborted message, you did something wrong. The problem is that you aren't actually supposed to flash ota.zip. What you're supposed to do is push ota.zip to your phone as update.zip, and leave it there. Don't touch anything else. What you will do after that is type 'adb push update.zip /sdcard/update.zip' in the command prompt (WITHOUT hitting enter yet, just get ready to). You will then select 'sdcard:update.zip' and press power and IMMEDIATELY AFTER pressing power, you will press enter on the command prompt to execute your adb push command. What this does is causes recovery to read the ota.zip file you uploaded and recognize it as a legit update, but you replace it with update.zip before it actually gets extracted (if your timing is good). So recovery reads the signature of ota.zip, but actually extracts the stuff in update.zip and runs that instead.
Hope that helps with some common problems I observed. Good luck, dudes.
Click to expand...
Click to collapse
Really good tips. I hope you don't mind - I am going to link to this to my original thread.
Troubleshooting Tip on Prerequisite Step 2: If you're working behind a firewall, router, or proxy server, you're going to have to configure SDK Setup to use an open port on that device, in order to download updates.
I won't go through the exact steps here, but if SDK setup is hanging, this is the most likely culprit.
Regards,
Corporate Dog
Corporate Dog said:
Troubleshooting Tip on Prerequisite Step 2: If you're working behind a firewall, router, or proxy server, you're going to have to configure SDK Setup to use an open port on that device, in order to download updates.
I won't go through the exact steps here, but if SDK setup is hanging, this is the most likely culprit.
Regards,
Corporate Dog
Click to expand...
Click to collapse
get a copy of linux livecd and then you don't have to actually set up the SDK or worry about any drivers.
attn1 said:
This isn't complete - this just gets you to clockwork and you having installed anything yet. You need to add steps to root or flash a rom that is rooted. Also, make sure to reference the unrevoked tool to install Clockwork after root so this whole ordeal can be avoided next time.
Click to expand...
Click to collapse
If you made it to clockwork using this method then you're rooted. Check eugene's updated instructions. Look at the 6/29/2010 update on his original post... http://forum.xda-developers.com/showpost.php?p=6820344&postcount=1
I will add a reference to the unrevoked tool.
modest_mandroid said:
If, on the other hand, your phone DOES show up in Android but not in recovery, or if it just blips on the screen for a second (when running the loop) as an offline device, then it might be the formatting of your sd card. Do NOT format your sd card from your phone or within Android. The ONLY time I managed to get the phone to show up in recovery without disappearing immediately was by removing the sd card, formatting it in windows or osx with an external card reader, copying the files over (new rom or rooting files), and then replacing it in the phone while the phone is off. After putting the card back in your phone, try the procedure again - go to the bootloader->hboot->recovery (while the cable is unplugged), then press the power button and immediately after plug the cable in (usually works when you plug the cable in about .2-.5 seconds later). If it does not show up at all, reboot the phone and try again, but do NOT let it boot back to Android. You can get back in to the bootloader by waiting until the 'HTC quietly brilliant' screen shows up and typing 'adb reboot bootloader' with the usb cable attached.
It took me a really long time to figure that out. I don't think the type of sd card matters so much as the formatting of it. I actually used the 2gb card that came with the phone, and it worked almost every single time after I reformatted the card.
Click to expand...
Click to collapse
Excellent troubleshooting tips. I added a note about formatting your SD card to the prerequisites.
ice3186 said:
okay so I think I the only one using a Mac in this rooting process. A few things I have learned and may already be known but I thought I would clarify.
1.) to get a loop to run on the mac i had to re-write the file loop.bat
this is the code that works for me and how to do it.
a.) rename the file to end in .sh not .bat the way it came
b.) open the file with TextEdit
c.) delete all of the text in it and write this in there
Code:
while [ "0" ]
do
{
./adb devices
}
done
d.) save the file back in the sdk/tools folder
e.) in terminal the command once you cd to the folder is ./loop.sh
2.) i have yet to be successful in the attempt to root so anyone knowing anything to help would be appreciated! But i am still cracking i think i am going to wear out the plug before i am done though.
Click to expand...
Click to collapse
Thanks. Added a reference to your post.
attn1 said:
it should be pointed out that the loop does nothing except tell you if you have a connection or not. When you plug in the usb port, it will respond after a few seconds, or it won't. Try again.
Click to expand...
Click to collapse
Noted in the original post.
Corporate Dog said:
Troubleshooting Tip on Prerequisite Step 2: If you're working behind a firewall, router, or proxy server, you're going to have to configure SDK Setup to use an open port on that device, in order to download updates.
I won't go through the exact steps here, but if SDK setup is hanging, this is the most likely culprit.
Regards,
Corporate Dog
Click to expand...
Click to collapse
Thanks. Added the workaround.
attn1 said:
get a copy of linux livecd and then you don't have to actually set up the SDK or worry about any drivers.
Click to expand...
Click to collapse
Thanks. Added a note to the top of the prerequisites.
gtg465x said:
Step 12.
If successful, you should see Clockwork Recovery and you now have Su and Superuser.apk installed! You can now reboot your phone into the OS to verify. If unsuccessful, repeat steps 11 and 12.
Step 13.
This step is optional, but it will save you the pain of going through all of these steps again in the future.
Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!)
Click to expand...
Click to collapse
In no way, shape or form are you done after set 12.
You need to do more than just get into Clockwork. That alone doesn't root the phone.
gtg465x said:
If you made it to clockwork using this method then you're rooted. Check eugene's updated instructions. Look at the 6/29/2010 update on his original post... http://forum.xda-developers.com/showpost.php?p=6820344&postcount=1
I will add a reference to the unrevoked tool.
Click to expand...
Click to collapse
My mistake. He not only updated his instructions, he updated his update.zip. That should do it.
Good job!
I was just wondering If I have device issues after it is rooted, is it possible to remove the root and flash everything back to factory defaults for warranty purposes like the windows phones or is it once the warranty is gone it is gone?
steezee said:
I was just wondering If I have device issues after it is rooted, is it possible to remove the root and flash everything back to factory defaults for warranty purposes like the windows phones or is it once the warranty is gone it is gone?
Click to expand...
Click to collapse
Dunno if you can reflash the stock recovery again if you replaced it with clockwork, but you can definitely flash the stock ATT rom again. You can download it from HTC's site: http://member.america.htc.com/download/Web_materials/Manual/HTC_Aria_ATT/HTCAriaOriginalShipROM.exe
Banging my head on the wall. Got it to detect device once on loop. Never again after that. Phone shows up in device manager. Formatted 8gb and 2 gb cards several times.
urge growing. ... want to . . break.. . . .. . .random objects. . .
attn1 said:
My mistake. He not only updated his instructions, he updated his update.zip. That should do it.
Good job!
Click to expand...
Click to collapse
Sorry, I should have mentioned that he updated his update.zip.
You guys are right , there are missing step in the tutorial to fully root Aria.
after i get in to the clockwork from the step above. i have to install the custom rom that can be found in the forum.
when i try to install "Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!) " . the process goes throught but the recovery is still the same HTC blue color recovery screen.
so before you insert your sd card into the phone after you format the sd card. remember to copy the rooted rom into the sd card so when you successfully get into the clockwork. you want to install the rom then your aria is rooted with superuser icon on the application.
after then you do the "Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!) step .
There are no steps missing from the first post. I rooted my Aria using that method. Just make sure you have the latest Root.zip from eugene's thread. He updated it the other day and if you try to use the older version of Root.zip with this method it will not work.
What you are doing is installing a custom rom, which is fine, but it's not required to root the Aria.
i was trying to get the clockwork to install and it only work after i load the liberated_aria_b003_signed.zip
before i load liberated_aria_b003_signed.zip , it still give me the default HTC recovery screen.
after i load liberated_aria_b003_signed.zip and install "Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!) " . i get the clockwork screen as the recovery screen .
i still can't get the side loading to show after i follow the step from here
•COMMON:
•Enable USB debugging (settings > applications > development > USB Debugging)
•adb remount
•adb pull /data/data/com.android.providers.settings/databases/settings.db settings.db
Linux/OS X:
•echo "update secure set value = 1 where name = 'install_non_market_apps';"|sqlite3 settings.db
WINDOWS:
•echo update secure set value = 1 where name = 'install_non_market_apps';|sqlite3 settings.db
COMMON:
•adb push settings.db /data/data/com.android.providers.settings/databases/settings.db
•Reboot phone and sideloading works. (thanks to fluffyarmada)
.
My screen first cracked and then the LCD completely went now... I have files I need to retrieve off the phone. It is rooted and running some ICS build... I believe the phone is in USB debugging mode, the screen still 'works' I can unlock the phone but nothing is displayed on the screen. Possibly someone could help me out with the adb process for pulling the contents off the /sd
Any help will be GREATLY appreciated, thank you for your time.
ur usb mass storage should still work. can u just plug ur phone to a usb port and get things off the phone ?
As previously stated. I believe the phone was in USB debugging mode. And now the screen is completely black... impossible to navigate to where i need to be.
You'll need adb setup on your computer, and you'll need to cd your way into the folder with adb.exe. Forgive me for hotlinking, but this will make it easier: Download this file, courtesy of NexusSHacks.com (I believe it is Zedomax around here). I would advise to unzip the contents in this file to your C:\Nexus directory, so that adb.exe is at C:\Nexus\adb.exe.
Now, plug in your phone. Open your start menu and search for "cmd" and open up Command Prompt. This is the basic Windows CLI (Command Line Interface).
First, you'll need to open the directory of the Nexus folder you created earlier. To do this, type in the command prompt:
Code:
cd C:\Nexus
Now, you want to make sure adb sees your phone:
Code:
adb devices
The adb service should start and if it sees your phone it will pop up a serial number. If there is no serial number, you can't use adb while inside android and you'll need to tick the option or find an alternative way. Assuming it finds your device, you are good to go.
In order to copy the /sdcard folder of your Nexus S, you will use the pull command. We will throw all of the files into C:\Nexus\sdcard, for reference. So in the command prompt, type:
Code:
adb pull /sdcard .\sdcard
It looks a little confusing but don't stress. Just make sure you type it in exactly (dot, correct slash, etc). This will take a little while since it might transfer up to ~15GB worth. You'll see a new line with "C:\Nexus>" with a flashing cursor when it is done. Then you can view all the contents of your sdcard at C:\Nexus\sdcard and do with them as you please.
Also note, for this you'll need up to ~15GB of free space on your C:\ partition, make sure you have this before you start. Good luck
old post I know, but I just dropped my Samsung Captivate (rooted with debugging on) and internal screen cracked (gorilla glass is perfectly fine!), so I am in the same boat. After DAYS... actually DAYS of trying everything from every forum I FOUND A FIX!!!
Now admittedly, I am unsure which of these two (or both) fixed the issue, but here is what I did:
via Google Play's online "shop", I installed "Auto Mount Your SD Card" by JRTStudio (admittingly, unsure if this did anything as I cannot verify if it installed or anything via the phone)
https://play.google.com/store/apps/...wsMSwxLDEsImNvbS5qcnRzdHVkaW8uYXV0b21vdW50Il0.
then I DL'ed MoboRobo and after a few frustrated phone reboots, usb cable connections and much cursing IT CONNECTED!
http://www.moborobo.com/
I am currently DLing all my files from my broken phone!
I had to pass this along as I said... NOBODY seems to know about this as it has taken me DAYS to do this! Not even ATT (Current carrier) nor Spring (whom I am switching to in a month or so) could help me!
You save my life with that "moborobo". Thank you very much.
Glad I could help!!!
Thanks went to both of u, quit important piece of knowledge.
One question; r u downloading "moborobo" on ur Android, on your pc or on both of them?
just on PC, not needed on the phone unless you want to go via WiFi
Harbb said:
If there is no serial number, you can't use adb while inside android and you'll need to tick the option or find an alternative way.
Click to expand...
Click to collapse
What do you mean by this?
My adb service doesn't detect my phone, I used Droidzone's tutorial. I believe usb debugging needs to be on for adb to work, which in my case is useless cause my screen is broken so can't turn on usb debugging.
This is what happens:
---------------------------
C:\>adb devices
List of devices attached
C:\>
---------------------------
---------- Post added at 11:31 PM ---------- Previous post was at 11:23 PM ----------
^when I say broken, I mean the whole screen is distorted, I cannot see anything
droidoidoid said:
What do you mean by this?
My adb service doesn't detect my phone, I used Droidzone's tutorial. I believe usb debugging needs to be on for adb to work, which in my case is useless cause my screen is broken so can't turn on usb debugging.
This is what happens:
---------------------------
C:\>adb devices
List of devices attached
C:\>
---------------------------
---------- Post added at 11:31 PM ---------- Previous post was at 11:23 PM ----------
^when I say broken, I mean the whole screen is distorted, I cannot see anything
Click to expand...
Click to collapse
Reboot to recovery. Bam, working ADB. You can navigate there pretty easily. Pull battery, then re-insert. VOL + & PWR, two click on VOL -, PWR button once. You're in recovery now.
QtADB also can be used is this case
http://qtadb.wordpress.com/download/
paskalion said:
QtADB also can be used is this case
http://qtadb.wordpress.com/download/
Click to expand...
Click to collapse
No go on this either.
Downloaded QtADB, ran the .exe
Pointed to the folder with the aapt and adb binaries, program opened up
Phone's connected and on (I can hear texts coming through), hit refresh a few times, still not detecting
polobunny said:
Reboot to recovery. Bam, working ADB. You can navigate there pretty easily. Pull battery, then re-insert. VOL + & PWR, two click on VOL -, PWR button once. You're in recovery now.
Click to expand...
Click to collapse
That's a little tough. I'm using a Galaxy S so I'm following instructions for that, but it's hard to know if I'm in recovery mode or not. Since adb doesn't detect the device, it's hard to know whether the phone went into recovery mode, or whether adb is setup correctly. It would be handy for a voice sample to play "recovery mode" once the phone boots into it.
droidoidoid said:
That's a little tough. I'm using a Galaxy S so I'm following instructions for that, but it's hard to know if I'm in recovery mode or not. Since adb doesn't detect the device, it's hard to know whether the phone went into recovery mode, or whether adb is setup correctly. It would be handy for a voice sample to play "recovery mode" once the phone boots into it.
Click to expand...
Click to collapse
You're in the wrong forum, then.
And whether or not adb is installed properly, you would know in your device manager under Windows. Appears as a device.
polobunny said:
You're in the wrong forum, then.
And whether or not adb is installed properly, you would know in your device manager under Windows. Appears as a device.
Click to expand...
Click to collapse
Ok... Galaxy S i9000 stuff goes in the Galaxy S i9000 forum.... that's probably why my other post got deleted! :laugh:
As for adb... it appears as a process in task manager, so it's running - I know that much. It's not appearing as a device in device manager (why would it if it's a process? or are you referring to my phone appearing as a device?)
Only areas I can think of that aren't correct are the environment variable and the way I'm doing recovery mode. Since I can't see the screen, I don't know which one is causing the issue! :crying:
Samsung broken??
Contact this guy in Paris , he's very good and friendly!! he repairs my blue Galaxy S3 in front of me
Tel: 0950 850 500 Direct Technique
repare-galaxy com
don't hesitate to call them because i know their skills and it's very good!!
tell them that u call from Mike ciao guys!!
Problem!
Harbb said:
Code:
adb pull /sdcard .\sdcard
It looks a little confusing but don't stress. Just make sure you type it in exactly (dot, correct slash, etc). This will take a little while since it might transfer up to ~15GB worth. You'll see a new line with "C:\Nexus>" with a flashing cursor when it is done. Then you can view all the contents of your sdcard at C:\Nexus\sdcard and do with them as you please.
Click to expand...
Click to collapse
Hey, I got to this problem and I got stuck. I also have a Nexus S with a cracked screen. When I put in the final phrase into the command window it just told me that 0 filles were pulled! Why didnt it pull my files?
What I am trying to do is get all of my pictures and others off the phone.
Please help!
SkullMblem said:
Hey, I got to this problem and I got stuck. I also have a Nexus S with a cracked screen. When I put in the final phrase into the command window it just told me that 0 filles were pulled! Why didnt it pull my files?
What I am trying to do is get all of my pictures and others off the phone.
Please help!
Click to expand...
Click to collapse
This happened to me as well. You have to make sure that your phone has its sdcard folder mounted. Type "adb shell" to get access to the phones command terminal. Then type in "mount /sdcard" I think, or maybe it was "mount sdcard". Either way will probably work so long as you are in the root directory of the phone. You can navigate around in the phone just like a normal linux terminal. "ls" shows list of files and folders in the current directory, "cd foldername" moves into a folder, "cd ../" moves back, "cd /" goes to root directory, etc. Anyhow, once you have mounted the sdcard, you can type exit to leave the shell terminal, and then issue the command "adb pull /sdcard .\sdcard" to get the files. I had a custom rom image in the root of my sdcard so the move took quite a while ~15 minutes. On success of the pull command you should see a bunch of statuses like:
pull: sdcard/data/somefile -> .\sdcard/data/somefile
pull: sdcard/DCIM/somefile -> .\sdcard/DCIM/somefile
.
.
.
XXXX files pulled. 0 files skipped
(Some more transmission stats)
Hope it works out for who ever reads this.
Side note:
On my phone the screen was smashed. I replaced it and it still would not turn on, but it was still running. I had a rooted phone with CM10 rom on it. ADB debugging was one (if its off your pretty much screwed). I started up the phone, and plugged in the usb cable. I tried to use both adb and fastboot from windows terminal. "fastboot devices" would echo back nothing, and "adb devices" would echo back my phone's device number but state it was offline. So to get it online I did the following:
1.) pull batttery.
2.) boot into bootloader (hold power and volume up) the phone shouldn't vibrate if it does you have just normally powered it on. It took me quite a few times to get this to go into the bootloader. To make sure you get in the bootloader type "fastboot devices". If nothing comes up you not there.
3.) once verified you are in the bootloader you need to go into recover mode. Press volume down twice and then hit power (this would normally move the cursor on your phone down to recovery and select it if you could see whats happening on the screen).
4.) wait a bit for it to load into recovery, try typing "adb devices". You should eventually see you device show up as online. At this point you may enter the shell as above, mount the sdcard, exit the shell and pull your files.
Windows instuctions:
Prerequisites are installing adb.exe and fastboot.exe via installing the Android SDK on your computer. They will show up in the platform-tools folder of the install location. Add that folder to your environmental path variable so you can run the ADB and fastboot commands from any folder. Install the ADB driver for your phone (allows you to issue adb commands to your phone when USB is plugged in) by plugging in your phone and going to device manager, find your phone which should show up as a exclamation point, right click update driver, click "browse...", then "let me pick...", click top entry something like "show all", and then let the list populate. On the left look for "samsung" and then select the first one that is something like "samsung adb driver interface". And you should be good to go.
Sorry for the long winded post, I just like to try and explain as much as possible.
Successfully Recoverd data
Well My Samsung S2's Screen broke down few days ago.. Now i have retrieved the data by following the 2nd method in the following article..! I Hope this works for you aswell...
I can not Post the link here.. PM me if you want the link...!
Hey guys,
I have a Nexus 7 2012 wifi only model. It has a cracked screen and need to retrieve data from it.
But the problem is that is has 4 users, 1 being administrative with pin lock. I can't remember the pin. And no usb debugging, nor rooted, no custom recovery, no unlocked bootloader, so can't remove the pattern via gesture.key method. Aroma file manager won't flash.
Also can't lose the data.
Please Help!
ClawSpark said:
Hey guys,
I have a Nexus 7 2012 wifi only model. It has a cracked screen and need to retrieve data from it.
But the problem is that is has 4 users, 1 being administrative with pin lock. I can't remember the pin. And no usb debugging, nor rooted, no custom recovery, no unlocked bootloader, so can't remove the pattern via gesture.key method. Aroma file manager won't flash.
Also can't lose the data.
Please Help!
Click to expand...
Click to collapse
Hi, I do not know if your data is recoverable, but try the following (you need a computer):
1. Install ADB here if you don't have it: lifehacker.com/the-easiest-way-to-install-androids-adb-and-fastboot-to-1586992378
2. Plug your Nexus 7 into your computer's USB port.
3. Turn the Nexus 7 on while holding PWR + Volume Up, this should get you to the stock recovery mode
4. Open a CMD/Terminal window and type the following:
Code:
adb devices
5. The window should show your device in recovery mode
6. Next type the following into the window:
Code:
adb pull /sdcard /backup/<location-on-computer>
7. Replace '<location-on-computer>' with the location that you want to backup your files to (Make sure to keep the '/backup/' in front), ex. your desktop
8. The line will stay blank until it is done, once it is, all your files should be in a folder named 'backup' wherever you selected.
Hope this worked! If you absolutely need the data, you can always get the screen replaced.
Brandon4466 said:
Hi, I do not know if your data is recoverable, but try the following (you need a computer):
1. Install ADB here if you don't have it: lifehacker.com/the-easiest-way-to-install-androids-adb-and-fastboot-to-1586992378
2. Plug your Nexus 7 into your computer's USB port.
3. Turn the Nexus 7 on while holding PWR + Volume Up, this should get you to the stock recovery mode
4. Open a CMD/Terminal window and type the following:
Code:
adb devices
5. The window should show your device in recovery mode
6. Next type the following into the window:
Code:
adb pull /sdcard /backup/<location-on-computer>
7. Replace '<location-on-computer>' with the location that you want to backup your files to (Make sure to keep the '/backup/' in front), ex. your desktop
8. The line will stay blank until it is done, once it is, all your files should be in a folder named 'backup' wherever you selected.
Hope this worked! If you absolutely need the data, you can always get the screen replaced.
Click to expand...
Click to collapse
Hey,
The device wont show up in adb while in stock recovery mode. Only sideload works. But still if i sideload, i lose all data.