Database Info

i think i have brick my dopod 818pro.. Please help

i think i have brick my dopod 818pro
have follow the step 1 and install without any error.
then installed the Cert_SPCS.cab and EnableRapi.cab.
then installed the Prophet_4.0.0.0.1_PV rom by running Upgrade_ROM.bat from the computer.
after that restat the device.
AND the phone boot after the HTC Innovation screen and stay at the loader screen.
NOw my screen only showing :
IPL 2.15.0001
spl 2.15.0001
gsm 02.69.21
os 4.0.0.0
and wouldn't boot in ???
anyone here please help
tq

finnally manage to boot in.
redo the step 1 in boot loader mode.
then installed the pdaviet 4.0.0.0.1 from pc
and it is done.
very nice screen
will try it out n c .
tq very much

Hi, how did you manage to solve the issue?
My situation is a little different.
-Load Step 1... ok Successful
-Load Upgrade_Rom.bat... completed
But when I reboot the PDA I just get this screen!!!
Nothing is responding.
PC cant detect the device.
Hard reset also get back to the same screen.
Please help

reboot your device into the bios screen (reset while holding camera button)
at that point i usually just put on the default WM5 comming from QTEK to reestablish operations.
i am using the prophet touch series from gullum and for that i do the following steps after having reestablished the WM5.
Put on PDAViet_TEMP
wait until phone restarts and shows 'Touch to get started'
Put on the Prohvet Touch (VIII or IX Beta)
Hard Reset (Com and Cam button, wait for the message asking to confirm afetr you release the reset button but hold on to com and cam buttons until message pops up) Confirm Hard Reset
So far i repeated this process about 6 times and it works every time
best of luck

need explanation
im planning to buy a dead prophet.....as the seller states...when he posted the pic, it still enters bootloader mode...but it shows
IPL: 1.00
SPL: 2.20.0001
Can this still be repaired? and is this possible? how can i repair it...it is being sold at a very cheap price

I've had similar issues and by just putting the original rom or the WM5 if you can enter bootloader mode thenit comes back to live. Once WM5 which is very stable is loaded, you can upgrade to the WM6 roms. Has always worked for me but it is a bit nerve racking to see the thing frozen. The key when upgrading is to use than WM5 rom and upgrade from there.

Tri-Color Bricked Tilt

My poor tilt is stuck at the tri-color screen and it doesn't have HardSPL installed. I can't get one installed to unbrick it since all the guides tell me that I need one before I can use any tools to do so. What is displayed on the screen is the following:
KAIS1*0
SPL-3.02.0000
CPLD-8

Do you have a microSD card? If so, you can flash your kaiser back to factory with an approved ROM. Search the forum for the SHIPPED that came standard on your Kaiser (or the ROM that came with your phone from your carrier). Use 7zip or WinRAR to extract the RUU_Signed.nbh from the download. Copy to the root of your FAT32 FORMATTED microSD and rename the file to KAISIMG.nbh. Reset your phone and hold the camera button. When the phone restarts it should quickly show you the tri-color screen then go to a screen that says loading. From there follow the on-screen instructions. This will give you back your default ROM.
IMPORTANT!!! ONLY DOWNLOAD AND USE THE ROM THAT SHIPPED WITH YOUR DEVICE!. If you look at the wiki, you will find a list of the shipped ROMs (Including the AT&T ROMs, hint).
Consider this a freebie. Any other time you would have probably been flammed for not searching. For any other questions I suggest you search for "Stuck at tri-color screen" and "Flashing from microSD".

I will gladly give you $50 for your bricked tilt. Otherwise...load the stock rom back on the phone.

Urgent Help Did I Brick My TP2

Please help.
I have the Verizon TP World Phone w/SIM card.
I downloaded the HARDSPL described as such: this package is for Rhodium CDMA-GSM worldphone version only (CDMA Touch Pro 2, not the original Touch Pro) devices. only RHOD400, RHOD500 modelids are accepted. this Hard-SPL supports WM6.5.
This process went successfully and I made it to the tri-color bootloader screen.
Next I ran this flashed this ROM NRGZ 21864, which appeared to complete successfully via PC, but when phone rebooted it just shows black w/Touch Pro 2 in middle of the screen.
Tried resetting, batter pull everything can't get anything to happen.
**Update: I was able to now get it into tri-color boot loader so what should I do with it now? It says SPL-1.00.Olinex, so its still unlocked. Should I just retry the rom again?
What did I do wrong? Is this phone dead? How do I get to bootloader? What should be my next step if phone is not dead.
Thank you!!!

Get a different rom that one didnt load or you could try reflashing doesnt seem as it took properly but no fears your phone is not bricked
Make sure you get a rom built for CDMA phones. this isnt the proper section for that goto RHODUIM CDMA

To Flash from the SD card, the .nbh file needs to be named "RHODIMG.nbh"
copy the .nbh file to a micro sd card, prefarably a 2gb or lower formatted as a FAT32
plug it in
get into the boot loader
i would recommend getting the stock ROM for your carrier and flashing that before moving to a custom ROM
hope that helps

ME TO
How do you get it to load in the bootloader menu ? Any luck with fixing it?

LECKEY73 said:
How do you get it to load in the bootloader menu ? Any luck with fixing it?
Click to expand...
Click to collapse
To enter the bootloader hold volume down and power (the red end key, not the sleep key on top) and press the stylus into the reset button. Once you see the tri-color screen you can release volume and power.

Same thing happened to me on my flash to that exact ROM. I guess sometimes it just doesn't flash correctly for some reason. No worries, enter bootloader mode and try flashing to MightyROM. After that, I was able to flash to whatever ROM I wanted. (But then I flashed back...MightyRom rules!!)

the spl 1.00 is fine. just go here it's for cdma phones only.

thanks everyone, got it back into bootloader via the challenging (hold both buttons and hit reset) Years of cosole gaming clearly paid off for those acrobatics.
Reflashed to original rom/radio, will put MightyRom back on..think I just needed to bump my head a bit, start over after some lessons and get this running better.

brick treo trying to flash hard spl help!

is there any way to flash hard spl without have activesync connection??

There was talk about a year ago of flashing via a mini-SD card, the idea was to take the nbh file that comes out of the Cheetah-unlocker.exe (you'll find it in its temp folder), put it on a Fat32 formatted mini-SD, and reset the Treo while holding the media/hands-free button.
I've never tried it, since I half-bricked a Treo trying to do it the ActiveSync way. I restored the Treo, btw, which I am wondering, most of the hard spl tutorials I saw for the Treo, they are incomplete because they lacked 1 crucial step: you have to unlock your phone. And I mean really unlock it, not code-unlock it. The very first step everyone needs to do is run MagicUnlocker to inject the SuperCID, then HardSPL will work. I bricked my first Treo because nobody mentioned the SuperCID (my Treo was bought unlocked already)
And, chances are, if your Treo boots halfway then stops, you can save it. Really, that's how I saved mine: you need any of Palm's official ENG ROMs, load it onto a Fat32 formatted mini-SD, and do the above mentioned reset method. Flash the ROM and your Treo is restored (remember, there has to be a way for the Treo to turn on for this to work.)

my phone bricked when i tried to hard spl unlock. and now my phone goes to the red/blue/green screen when i hold the ppt button and reset. and will freeze on the windows mobile splash screen if i just do a reset
so if i do what u say (load official rom on formatted sd card + reset holding ppt) i will be able to save my treo?
thanks for the response btw

Ah, sorry for late reply, yeah, as long as you will get to the rainbow colored screen it can be saved (Palm ROM renamed to CHEEIMG.nbh on a Fat32 formatted MiniSD card), reset while holding ppt and it'll recognize the ROM. Plug in an AC charger too to keep it going.
It wasn't mentioned, but I advise you take out your SIM card while you do this. It might make a difference (in fact, I always do this, call it memories of the Samsung Blackjack ROM upgrade rule)
Maybe that's why a Hermes Radio can't be overwitten sometimes...

[Problem] Flashing HardSpl trough MicroSD fail (pls help)

I had a StockSpl on my Htc touch pro and I wanted to flash an unsigned Hard-SPL from my MicroSD because I wasn't home and I didn't have the USB cable. After the screen loaded 100% the device restarted I took off the MicroSD and now it keep showing this tri-color screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
(I've also attached a picture)
If i try to flash again from MicroSD the same HSPL it loads until 100% then restart and start to load again until i get the MicroSD card off. Or if i try to flash other StackSPL or any other ROM it stays on Loading on a grey screen.
After I went home I tried to flash the HSPL again from my computer using the USB cable, it start to load 0% then it does nothing. I've tried to flash StockSpl and other ROMs from the computer too but it does the same.
I think i've tried anything but nothing seems to work ... if someone can help me pls ... i've searched the entire forum and there's someone that had almost the same problem here: http://forum.xda-developers.com/showthread.php?t=566796
but noone had any solutions.

You can't flash hard spl off your sd card; it's got to be done through a usb cable.
Just read through the hard spl thread; it's long, but your situation has probably been addressed. I did it almost 3 years ago, so I don't remember the tricks. That's the case with most posters, I'm afraid. Just read the thread.

can u pls tell me which thread?
this one?: http://forum.xda-developers.com/showthread.php?t=410150
or this one?: http://forum.xda-developers.com/showthread.php?t=448008

Either, but read the first one. You can also look in the unlocker thread. Hell, you may just want to buy the unlocker and run that. It will flash hard spl, and the directions may be better.

I just hope they aren't trying to HSPL(hard SPL) a CDMA device :S I've made the mistake to assume the person that was posting in this forum had a GSM device and they really screwed up after a third attempt at flashing HSPL!
Usually if I have a difficult time flashing my Fuze or TP(both GSM), I remove everything to include the battery, connect the USB to an available USB port on the computer then hold the volume down key while connecting the device to the USB cable. Probably not the most friendly way but it certainly will tell you if there is a problem with your USB port/cable or even device!

My htc raphael is GSM
I've tried to hold the volume down button but it's always the same
There's no problem with the cable just that I can't flash anything because I'm stuck with a stock-spl and I can't flash a hard-spl either. When I try to flash something from the computer it starts to flashing with 0% then nothing happends until the RUU gives me the 262 Error. And when i try to flash from my mSD it just stuck with a Loading screen.

Xadow said:
I had a StockSpl on my Htc touch pro and I wanted to flash an unsigned Hard-SPL from my MicroSD because I wasn't home and I didn't have the USB cable. After the screen loaded 100% the device restarted I took off the MicroSD and now it keep showing this tri-color screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
(I've also attached a picture)
If i try to flash again from MicroSD the same HSPL it loads until 100% then restart and start to load again until i get the MicroSD card off. Or if i try to flash other StackSPL or any other ROM it stays on Loading on a grey screen.
After I went home I tried to flash the HSPL again from my computer using the USB cable, it start to load 0% then it does nothing. I've tried to flash StockSpl and other ROMs from the computer too but it does the same.
I think i've tried anything but nothing seems to work ... if someone can help me pls ... i've searched the entire forum and there's someone that had almost the same problem here: http://forum.xda-developers.com/showthread.php?t=566796
but noone had any solutions.
Click to expand...
Click to collapse
Naughty Naughty..
I guess you realise now that you should ALWAYS read read read before modifying your phone in any way.
What EXACT file did you originally flash to your phone via microsd card and where did you get it from?
If you go into the bootloader screen and then connect the usb cable does it show "usb" at the bottom of the screen?
PLEASE STOP TRYING TO FLASH HARDSPL FROM MICROSD AS YOU CANT DO IT. If you could then it would be in my guide..
Mark.

mskip said:
Naughty Naughty..
I guess you realise now that you should ALWAYS read read read before modifying your phone in any way.
What EXACT file did you originally flash to your phone via microsd card and where did you get it from?
If you go into the bootloader screen and then connect the usb cable does it show "usb" at the bottom of the screen?
PLEASE STOP TRYING TO FLASH HARDSPL FROM MICROSD AS YOU CANT DO IT. If you could then it would be in my guide..
Mark.
Click to expand...
Click to collapse
Thanks for replying
Yes ... I did read the part with the SD flashing but i thought it's not a bit deal to flash from mSD since the flashing via activesync is so easy.
Well ... i extracted the RUU_Signed.nbh from the Hard-SPL found HERE and i copied it to the mSD (MicroSD) and renamed it RAPHIMG.nbh.
I restarted my phone holding the volume down button and it started to load until 100% then it restarted and showed the bootloader screen and after a couple of seconds start to flash the HSPL again so after it completed 2 or 3 times of flashing and restarted i took the battery and the mSD off (I DIDN'T TOOK THE BATTERY WHILE IT WAS IN THE PROCESS OF FLASHING). And when i started the phone again without mSD it showed the bootloader screen like it was waiting to get a .nbh file on mSD to start flashing again.
No matter what i do my phone start in bootloader and down it shows "Serial". If i connect the usb it shows "USB".
I tryed to do a hard reset and it seem to work but after it finish and the phone restarts is stuck with the same tri-colour screen.
Sry for trouble and thx again

I guess I missed the part in the OP where you said it was stuck in bootloader. That's not good. I would try flashing the stock raphael rom (assuming you have it). Have you tried that? I dunno, you may be stuck for good.

Xadow said:
Thanks for replying
Yes ... I did read the part with the SD flashing but i thought it's not a bit deal to flash from mSD since the flashing via activesync is so easy.
Well ... i extracted the RUU_Signed.nbh from the Hard-SPL found HERE and i copied it to the mSD (MicroSD) and renamed it RAPHIMG.nbh.
I restarted my phone holding the volume down button and it started to load until 100% then it restarted and showed the bootloader screen and after a couple of seconds start to flash the HSPL again so after it completed 2 or 3 times of flashing and restarted i took the battery and the mSD off (I DIDN'T TOOK THE BATTERY WHILE IT WAS IN THE PROCESS OF FLASHING). And when i started the phone again without mSD it showed the bootloader screen like it was waiting to get a .nbh file on mSD to start flashing again.
No matter what i do my phone start in bootloader and down it shows "Serial". If i connect the usb it shows "USB".
I tryed to do a hard reset and it seem to work but after it finish and the phone restarts is stuck with the same tri-colour screen.
Sry for trouble and thx again
Click to expand...
Click to collapse
As Farmer Ted said your best bet now is to download your ORIGINAL Rom (from your provider) and flash it from your pc with the usb cable attached. The phone had to be in SSPL mode before running the RUU which is why everything was packed in a single exe. You may have corrupted your SPL in which case you have bricked your phone but if you can manage to flash a Stock Rom then the Stock SPL should be reflashed and you can start again with the HardSPL by following the CORRECT instructions and not making up your own lol.
Good luck.
Mark.

When i bought my phone, the first thing i did was to dump the rom. So now i rebuild it from raw and tried to flash but it didn't work so i went to Orange site and i downloaded the official ROM then started to flash and ... IT WORKS
I think that the ROM was corrupted not the SPL, and since the SPL was stock it didn't allow me to flash other ROMs other then the official
Thanks for all guys I couldn't done this without your help
P.S: why did it allowed me to flash the official rom but the hspl not?

It didn't flash the hard spl because you did it all wrong; those rebuilt roms aren't exactly the same as the stock roms, so it's not surprising that wouldn't flash. Good job finding the original shipped one, though.
Now, just read mskip's instructions and you should be good to go. I think the trick is just to enter bootloader, then connect to your pc through the usb cable.