Hello!
I Have problem with flash my spv c600 to original orange rom
this is in bin format and who tell how can i flash my phone ?
Thx.
semixor said:
Hello!
I Have problem with flash my spv c600 to original orange rom
this is in bin format and who tell how can i flash my phone ?
Thx.
Click to expand...
Click to collapse
download mtty.exe form the internet use it to flash the bin file back to your phone make sure you've cid your phone frist
guide to flashing bin file
1) make sure your phone is CID unlocked
2) press ctrl + alt + del to get into the task manager, kill the process 'wcesscomm.exe' and make sure activesync isnt running
3) download mtty.exe
4) turn your phone off, press and hold the camera button and turn the phone on, should boot into the three colour screen
5) connect this to your computer using usb cable
6) run mtty, should be a 'USB' button showing up, if not, select it from the drop down menu
7) when the white screen shows up, press enter once until you get 'Cmd>' prompt
8) at this promt type in l c:\filename.bin (but make sure you have the bin file copied over to your C: drive, and that is a SMALL letter 'L' just before the command
9) let it do its thing, when your presented with the 'Cmd>' prompt again, just unplug your phone, pull the battery out, put it back in and boot. should work!
good luck!
(I am not responsible for any damage you do to yourself or your phone!)
guys thx but i have an error:
Cmd>l c:\OrangePL.bin
clean up the image temp buffer at 0x8C080000 Length 0x03B00000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Cmd>
What i have to do ?
Hi,
I didn't see any post about using MTTY on Kaiser.
If I did a bad ROM flash with my previous device (HTC Universal), I could always fix this by clearing the FAT table with MTTY.
Believe me... if you flash and it stops ad 85% you will be very happy if you can use this tool!
Reason I started this thread is to help out people who are having such a problem with there Kaiser!
This is the correct procedure to get you out of trouble
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
Incase of an emergency it could be very helpfull I think!
Thank you all for providing the input in this thread so I could make this small user manual!
Happy flashing!
Leo
Well... seems like nobody bricked his device yet!
That's cool....
I've read in many places about people using MTTY on thier Kaiser to get it to boot after a bad flash, but I can't remeber where. And I don't know where they got their info from.
I could attach MTTY here but I'm a bit scared if I do is that people going to blame me if they brick there device!
That's why I'm asking someone has experience with it.
It could be usefull for a lot of people.
DaveShaw said:
I've read in many places about people using MTTY on thier Kaiser to get it to boot after a bad flash, but I can't remeber where. And I don't know where they got their info from.
Click to expand...
Click to collapse
You supply a ROM that people can use to Brick thier devices (if they don't Hard SPL).
I suppose that's why they invented Big Red Font's and disclaimers.
If you do decide to post it, I'd get _Alex_ or Mike to add it to the Sticky.
P.S. I have yet to expirence it myself.
Hahaha... yes you are right
Ok I will attache MTTY.
Thanks,
DaveShaw said:
You supply a ROM that people can use to Brick thier devices (if they don't Hard SPL).
I suppose that's why they invented Big Red Font's and disclaimers.
If you do decide to post it, I'd get _Alex_ or Mike to add it to the Sticky.
P.S. I have yet to expirence it myself.
Click to expand...
Click to collapse
MTTY (How to fix a bad ROM flash?)
Is this thread can help you ?
http://forum.xda-developers.com/showthread.php?t=370169
I can't find the original post that talk about the procedure to unbrick kayser with
MTTY.
Hi !
I used it once.
The "info 2" works as designed ;-)
greetz
A clear procedure would be nice so you can unbrick your device easy using MTTY.
Thanks,
tyoine said:
Is this thread can help you ?
http://forum.xda-developers.com/showthread.php?t=370169
I can't find the original post that talk about the procedure to unbrick kayser with
MTTY.
Click to expand...
Click to collapse
Thanks for confirmation!
flushbeer said:
Hi !
I used it once.
The "info 2" works as designed ;-)
greetz
Click to expand...
Click to collapse
If you have a bad flash....that's no reason to worry.
I haven't had to use MTTY to recover.
In most cases, if there's no issues with the Rom itself...you can pop out the battery and re-flash the same ROM from BootLoader Mode. This will also work if for some reason your computer crashes or loses power & restart during the FLASH.
If the Rom has issues.....the flash will not complete and the device will be stuck in BootLoader Mode. At this point,you must FLASH a FACTORY ROM!!
Pop the battery off 1st, power up the device, device will power up in BootLoader Mode, connect to pc & FLASH your devices FACTORY ROM. This will restore your device back to it's original out the box settings.
The above only works if the device has been put through the Hard SPL or SuperCID process.
I personally have never tried to flash a cooked ROM without unlocking any of my devices. From what I've read what others have experienced...the flash would just fail and they're stuck in BootLoader Mode.
Myself ... I've experienced bad flashes, bad cooked roms that I've cooked, lost power to a pc & had my pc crash during a flash. Listed above is how I've recovered. There is life after Bootloader Mode.
The only time you have to worry is if your device does not power up at all
As a public chef...it's your responsibility to set the parameters of your ROM! Meaning, Radio, HardSPL, program conflicts, etc.
You are not ultimately responsible if someone bricks their phone but if they pushed the issue, you could be hit with some form of liabilty because you failed on providing a simple Disclaimer that sets the expectation.
I hope I've been helpful.....
That's clear
Thank you,
Leo
Okay, MTTY is a very useful tool & can help save your butt on many occasions.
A few of those occasions include:
1. Bad flash or installation of HardSPL
2. Bad Flash of a ROM.
There are several other problems that can arise & be mended with the use of MTTY. The most common use is for recovery of any flash process resulting in an RUUBNH error.
For most of these error you want to use MTTY to reboot the low level CE of your device to flush out any bad blocks.
Use of MTTY to recover from these errors is usually simple. The basic outline of how to use MTTY to resolve these errors is as follows:
1. Right click on the quicklaunch activesync icon on the lower left quadrant of your pc. (You can also just open up the A/S program)
2. Select Connection Settings.
3. Uncheck the box labeled "Allow USB Connections" & then Click "OK".
4. Open MTTY & select "USB from the Port options drop down menu.
5. Select RTS/CTS from the Flow Control Settings & click "OK"
6. Pay attention, because for a brief mmoment MTTY wil report whether or not it could establish a port connection to USB. If you are successful, a Command window will open.
7. Hit the "Enter" key on your PC twice. You should then see a command prompt that looks like this "cmd>".
8. At the command prompt (cmd>) you should enter the command "boot".
This will reboot the device & report back about any errors or bad or erased blocks.
9. If your device was just hung, it should be fine after the reboot. If it returns to Boot Loader however, it means there was a problem with bad blocks.
10. If errors were reported & you end up back at the Boot Loader screen, then repeat the "Boot" Comand at the (cmd>) prompt.
It can sometimes take two or three boots to fully recover from RUUNBH errors, so if at first you don't succeed keep trying & remember to keep notes about any errors reported in the MTTY info window.
Other Information: MTTY needs to have full access to the USB port. Some anti-spyware, anti-virus & firewall programs can prevent MTTY from gaining the port access it needs. McCaffee in particular should be temporarily disabled & some firewall programs may also need to be disabled.
don't work damn
this is my pda
RUUNBH
KAIS 130
SPL-1.93.0000
CPLD-8
USB
this is mtty
cmd
Command error !!!
Cmd>boot
Command error !!!
Cmd>
this rom RUU_Kaiser_ATT_WWE_1.51.502.0_Radio_sign_22.45.88.07_1.27.11.31_Internal.exe start, but at 1% kaiser reboot...
anyone know how much htc customer care ???
pedro_se_rooot said:
anyone know how much htc customer care ???
Click to expand...
Click to collapse
When I sent mine in to look at a problem with connecting via 3G, I was quoted:
a) I'm responsible for shipping to the centre in Texas, US. (Don't know if there might be one closer to you).
b) There would be a charge of USD$28 for diagnosing the problem and producing an estimate to fix. They would call me with the estimate.
c) If I agreed to the fix, the $28 charge would be waived and I would be charged the estimated amount.
d) If I decided against the repair, I would be charged the $28 fee.
e) They would also charge for shipping the unit back to me, typically, about USD$50 for North America.
In my particular case, however, they have repaired the phone and shipped it back -- apparently at no cost to me, other than getting it down there. I guess they figured it was a 'in warranty' problem.
/drt
Hi there,
Is your device dead or still responding?
Can you come into bootloader?
Did you follow this step before you connected your device and opened MTTY?
It's very important you do!
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
Please tell me?
pedro_se_rooot said:
don't work damn
this is my pda
RUUNBH
KAIS 130
SPL-1.93.0000
CPLD-8
USB
this is mtty
cmd
Command error !!!
Cmd>boot
Command error !!!
Cmd>
Click to expand...
Click to collapse
the device iss not dead (i think) but with Mtty work only info and task 8.
i've follow all the step and killed active sync.
EUREKAAAAAAA
i've follow this guide
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
i just tried to update my HTC PU10 windows mobile 5 to WM6 but then the screen got blank and now i think its in boot loader screen as i read in most of the forums. i read most of the forums abt this for 7hrs now and still stuck coz im new to these.
im using windows 7 on my pc so i cant use Activesync so im using windows mobile device center to connect
i tried connecting to mtty1.42 but my MDA dosnt detect in USB as most of the forums say but when i connect to the pc my MDA screen gose serial to USB v1.01 it mean im in the boot loader screen am i right ? so please tell me wht to do next
thanks in advance
Mudith
Welcome to forums
Have a read on the Wiki here:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Hope it helps,
ok i got my MDA working have to use Windows XP. ROM Update Utility dosnt detect the MDA from USB on Windows7
Windows XP is the best
thanks guys for ur support
hy mudith
i have the same problem with my pda...so please tell me what to do next...i read on forums but my pda doesn't connect on my pc....!!! i don't know what should i do..!!!
Belated Help
Firstly, remove both the SIM card and any memory card. Make sure your battery is charged as well. Can you get into the bootloader (Light button, on/off button and reset button all at the same time)?
If so then your screen should be showing 'Serial' at the top and a number at the bottom. Plug the cable into the XDA and into your PC (it IS a PC and not an iMac I'm assuming?). What OS are you using? XP, Vista or 7?
You need to ensure that 'connect via USB' is DE-SELECTED in either activesync or Windows mobile device centre.
With the cable plugged in, the 'serial' should change to 'USB'. If so all is good. If not, try another cable!
You may also need to ensure you have the correct drivers loaded for Vista and Win 7. I can't get it to work under Win 7 but I can under Vista. XP is preferred for stability for me though.
Now, assuming you have USB on the XDA screen, run mtty (attached to this post) and select usb as the connection type.
Then press enter and you should get a 'USB>' command prompt in the window on the PC. Type (not copy paste) the following:
set 14 0 <press return - don't type this bit obviously!>
Task 28 55aa <press return - don't type this bit obviously!>
Allow each to finish before typing the next and allow the command prompt to appear before exiting.
Then exit mtty and flash a good ROM, I use VNInt with HomeScreenPlus.
Good Luck!
I was upgrading my Polaris from one 6.5 rom to another when my computer crashed...the process was to about 28%...I restarted the pc but the phone is stuck on that multi coloured screen...i tried a hard reset but it still goes the multi coloured screen...Some assistance or any would be really appreciated...Help!!!
You can try this:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
i hope you will be happy after .. thanks
Hi Guys,
Most of us may know this method, but thought of putting it on the forum anyways.
Requirements:
1. You will need a Virtual PC for this method, either VMWare Workstation or MS Virtual PC. If you don't know how to use/setup Virtual PC, google it.
2. We will flash the Wizard by putting it in the bootloader mode.
Procedure:
1. Setup a Windows XP Virtual PC and start it.
2. Backup your phone.
3. Remove Memory and Sim card.
4. Remove phone battery and wait for 10-15 seconds.
5. Insert battery.
6. Press the power button for only a second.
7. Hold the camera button until you see the 3 band colored (red, green and blue) screen with the IPS/SPL info.
8. Connect the Wizard to your computer.
9. Windows 7/Vista (which is the primary/main Operating System) will add drivers, you may or may not get a message.
10. In the Virtual PC, goto the menu where you can connect/disconnect removable devices.
11. Here the Wizard will be listed as a USB device, you can identify it easily.
12. From here on you can flash the ROM, i recommend you follow the procedure listed in the "How to flash a new ROM to your Wizard... a little tutorial!" thread 298613.
Note: You may experience issues with this method. It is recommended to keep a copy of Virtual PC seperate.
1. Sometimes the flash progress may be stuck at 0%.
2. Shutdown the WinXP Virtual PC and try again.
3. It the Virtual PC doesn't starts, delete this Virtual PC file and use the backup (create a copy of the Virtual PC file first).
Happy Flashing.
Disclaimer: Info provided in good faith, I am not responsible for any damage/loss of any kind that you may experience following this procedure.
Your method is way too complicated. I flashed my wizard from windows 7 using this guide: http://forum.xda-developers.com/showthread.php?t=485293
Thanks
Thanks for the link, the RUU was able to flash the Hornet 5 ROM (thread 416636)perfectly, but it could not flash the RUU_TMobile_US_226102_22610105_022511_WWE_Ship, I got "file not found" error.
I wish there was a universal Windows 7/Vista compatible RUU for Wizard.
You are making it too hard! Download the Vista drivers I am uploading-its for Windows 64 bit. Restart your computer while holding down f8. Turn off digital signing of drivers. Put your Wizard in bootloader mode and connect to pc. Open (from the Start Menu) CONTROL PANEL>HARDWARE AND SOUND>DEVICE MANAGER. Find your ppc in the listed menu. Hit update driver. Just go through the menus hitting next until you get to an option where you hit "HAVE DISK". Hit browse, find where you have it on your computer and install. SEARCH IS YOUR FRIEND, TRY IT, USE IT, LOVE IT.