Related
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
denflorida said:
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
Click to expand...
Click to collapse
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
1. Disconnect your phone from the usb cable,shut down any firewall,disable any Anti virus,Reboot your PC.
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. On your PC Open windows Task Manager...>Tab Processes...>wescomm.exe...>End process
4. Power off the phone completely (Not stand-by,shut off completely),or you may take the battery out for few seconds
5. Make sure your phone is not Connected to the PC via USB cable and remove the dummy Sdcard or mini-Sd card
6. Get your phone into Bootloader mode (Multicolor screen) by pressing camera button + Power on button
7. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Be sure that your battery is charged over 70%)
8. "USB"will appear on the bottom of the screen of the Bootloader (Multicolor screen)
9. Run the Upgrade again and it will work fine without any problems.
10.Never use Bluetooth sync for the Upgrade
While upgrading, the ActiveSync program will not go on, however the upgrade is running.Please be patient when you're flashing your device, even if 98%. It can wait a little bit, 5 ~ 7 minutes.
Don't cancell the flash or get the phone off the usb cable till it confirms "Congratulations" or stops with an Error!!!
Hope it'll work, Good luck
Hi, this is the first time i saw a Paki guy on this web. I know there is alot of talent in IT profession in Pakistan. Anyway its good to see u here and i got a relief that with the help of a senior member like you i can get my phone work again.
To cut the chase, I have X01HT by Softbank Japan. It is Herms200 by HTC Japanese WM5 ROM. I have installed Asukal's English MUI and it was working fine for me. Now i'm planning to visit Pakistan this month so i though to unlock the sim and i used Prof v3a to unlock. I've successfully unlocked the sim and i guess CID also. When i use some other carrier's sim, i can receive the calls but cant make the calls out coz Softbank rom has a security which comes at screen and ask for password and dont let me do anything on the PDA. After studying alot on this forum i figured that i need to change the rom to get rid of that password message. i used the Olipro's Hard SPL and got bootloader 2.10 Olipro. I checked the other necessary stuff and when satisfied i started rom update. I end up with the same message of Error 260. Now my phone has no OS and it starts at bootloader. i tried everything possible like i make sure to remove all firewalls on my PC, used all the versions of Activesync and everything possible that i could. I trust that there is nothing wrong with the ROM etc but it is with connection.
Now if i update to the original ROM, i'm afraid that it will also upgrade my Bootloader and could never be able to flash english rom. I'm really depressed for the last three days and loosing sleep as well. I trust that you or any other senior member can help me with this.
Thanks in advance and looking forward anxiously.
Farrukh, wrong forum.
You know you have a Hermes, then you should know to post your questions in Hermes related forum, not wizard.
denflorida:
Try to update other Radio-only ROMs in xda's FTP server.
Sorry Brother, i know i have herms but i couldn't find some related topic in herms and i figured that Activesync problem is the same in all devices.
Anyway, thanks for the prompt reply. I'll try to find some from Herms.
Thanks
8125 rom update
i have tried to do a rom update on my 8125 g4. i recently purchased it off ebay and i have two problems. the reason i want to update it is because when i try to enable the wifi my device freezes. the other problem is that i can not seem to get the phone into boot loader mode. i have tried :
-turning the phone off and holding the camera button as i turn it on.
-holding the camera button and pluging it in to a usb port.
- using wizard service tool to enter boot loader mode.
after each of these different attempts i had to either remove the battery for 3 secs or hold the reset button for a few seconds before i can turn it back on. the phone still turns and just i can not use the wifi
Yes!!! Thank you! your instructions worked for me and got me past the Error [260] with my 8125 .
zabardast_1 said:
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
Click to expand...
Click to collapse
Thanks! Worked for Topaz and latest radio update.
I want to start out by saying I'm really sorry if I'm asking something stupid but I am a complete newbie and do intend to learn as much of this on my own as I can....
I took my brand new AT&T Tilt and I connected it to my Vista Laptop when it was charged fully and used the built-in Windows Mobile Device Center to do a quick connect (like a guest connect where files can be transferred but stuff isn't synched) and ran kaiser_HardSPL which gave me a white screen rather than the expected tri-color screen.
I found the solution for the white screen and did a reset by pushing the stylus into the small hole space on the bottom of the Tilt and then connected it again to my laptop and copied over JumpSPL1.56-KAIS to the phone. I then ran that app from the phone and the tri-color screen showed up. When 'USB' showed up on the screen I disconnected the USB cable for about 10 seconds and plugged it back in. The text 'USB' stayed on the screen and nothing happened after that. I then used the stylus again to reset the PDA again and I am now at my current step.
Am I ready to put a ROM on now? I'm so new to this and I definitely want to learn just not sure what's next....is my CID unlocked? Did everything go correctly or did I miss out on some important step?
What should I do next if I want to put a new ROM on? Whatever help anyone can give me would be very much appreciated.
Looking forward to becoming an active and contributing member to this great community!
Gas Addict said:
I want to start out by saying I'm really sorry if I'm asking something stupid but I am a complete newbie and do intend to learn as much of this on my own as I can....
I took my brand new AT&T Tilt and I connected it to my Vista Laptop when it was charged fully and used the built-in Windows Mobile Device Center to do a quick connect (like a guest connect where files can be transferred but stuff isn't synched) and ran kaiser_HardSPL which gave me a white screen rather than the expected tri-color screen.
I found the solution for the white screen and did a reset by pushing the stylus into the small hole space on the bottom of the Tilt and then connected it again to my laptop and copied over JumpSPL1.56-KAIS to the phone. I then ran that app from the phone and the tri-color screen showed up. When 'USB' showed up on the screen I disconnected the USB cable for about 10 seconds and plugged it back in. The text 'USB' stayed on the screen and nothing happened after that. I then used the stylus again to reset the PDA again and I am now at my current step.
Am I ready to put a ROM on now? I'm so new to this and I definitely want to learn just not sure what's next....is my CID unlocked? Did everything go correctly or did I miss out on some important step?
What should I do next if I want to put a new ROM on? Whatever help anyone can give me would be very much appreciated.
Looking forward to becoming an active and contributing member to this great community!
Click to expand...
Click to collapse
Quick question, and I'm not trying to be funny or anything, but did u read?
Thanks for the quick reply -- I did read the different threads that I thought would be dealing with this but was unsure of what to do after I did the white screen fix. The white screen fix said there was a way to test if it worked by checking a splash screen but when I ran that it said make sure you've already done HardSPL first otherwise it can brick your phone so I wasn't sure if I did actually do that step properly or not (of installing HardSPL).
I'd appreciate any help you could give me. Thank you again for taking the time to read my post!
Bronx31 said:
Quick question, and I'm not trying to be funny or anything, but did u read?
Click to expand...
Click to collapse
I can answer that!
I apologize for missing something obvious -- could anyone please point me to which thread I should look at?
Thank you.
No your device is still not ready.
http://forum.xda-developers.com/showthread.php?t=354061
You're on the right track. From what I gather you can indeed flash something at that stage on SSPL or continue on to flash HardSPL (which is what I believe you intended to do!). Get back to the stage you were at and, from the thread in which you found JumpSPL, flash HardSPL onto your phone. After that point you are totally ready to become a slave to dutty's roms...
Look here and ye shall find: HardSPL will not install - WHITE SCREEN: SOLVED
Well, first correctly install HardSPL, then go on flashing a ROM. You may find my FAQ usable. See my signature.
Nono... one more step to go.
After disconnect and connect usb flash hardspl then softreset.
bmueller77 said:
Well, if you correctly installed HardSPL which sounds like this, go on flashing a ROM. You may find my FAQ usable. See my signature.
Click to expand...
Click to collapse
Laurentius26 said:
Nono... one more step to go.
After disconnect and connect usb flash hardspl then softreset.
Click to expand...
Click to collapse
Already corrected it. But you were faster ^^
Thank you to all of you -- you're all being very helpful!
I ran the flash-hardSPL (ran the file in that folder called KaiserCustomRUU) and it gets all the way to where it is updating the rom image to the kaiser-hardSPL version and it shows 0% on my phone and 0% on the PC and after about a minute or so it says ERROR [262] : UPDATE ERROR ... it instructs me to remove my battery for 3 seconds, put it back in and try again.
I've done this twice now and keep getting the same error -- any ideas on what I'm doing wrong?
Thank you once again.
The only thing I can think about is that your phone is simlocked.
Do you have the usb cable connected straight to the pc or do you use a usbhub?
Gas Addict said:
Thank you to all of you -- you're all being very helpful!
I ran the flash-hardSPL (ran the file in that folder called KaiserCustomRUU) and it gets all the way to where it is updating the rom image to the kaiser-hardSPL version and it shows 0% on my phone and 0% on the PC and after about a minute or so it says ERROR [262] : UPDATE ERROR ... it instructs me to remove my battery for 3 seconds, put it back in and try again.
I've done this twice now and keep getting the same error -- any ideas on what I'm doing wrong?
Thank you once again.
Click to expand...
Click to collapse
Oh yes, that's true. I didn't realize I had to unlock my phone before I could start this process...I guess I confused it with CID unlocking or something.
I must have missed the part in the newbie FAQ about phones needing to be sim unlocked for all this stuff to work.
I guess I will have to get it unlocked first! Very much appreciate the prompt replies.
oh i just realized my SIM wasn't even in the phone while I was doing this (since I took it out during the white screen fix) -- would putting the SIM back in still create the same problem if my phone isn't unlocked?
Laurentius26 said:
The only thing I can think about is that your phone is simlocked.
Click to expand...
Click to collapse
You mean CID-locked, right?
Perhaps you could try another CustomRUU. Check this one http://forum.xda-developers.com/showthread.php?t=334890
Gas Addict said:
Oh yes, that's true. I didn't realize I had to unlock my phone before I could start this process...I guess I confused it with CID unlocking or something.
I must have missed the part in the newbie FAQ about phones needing to be sim unlocked for all this stuff to work.
I guess I will have to get it unlocked first! Very much appreciate the prompt replies.
Click to expand...
Click to collapse
No, a SIM-lock does not affect flashing.
So you ran JumpSPL from your phone, saw USB displayed on the screen, unplugged the usb cable, replaced it and then ran the hardspl provided from the thread I linked you to? There is no soft resetting going on between seeing USB on the screen and initiating the hardspl flash.
arexben said:
So you ran JumpSPL from your phone, saw USB displayed on the screen, unplugged the usb cable, replaced it and then ran the hardspl provided from the thread I linked you to? There is no soft resetting going on between seeing USB on the screen and initiating the hardspl flash.
Click to expand...
Click to collapse
Hi arexben,
I actually was an idiot and soft reset after unplugging and then plugging in the USB and not seeing any change on the screen.
Now if I put JumpSPL on my PDA and try to run it, it won't run saying it can't be opened because its either not signed w/ a trusted certificate or one of its components cannot be found.
Thank you so much for everyone trying to help me ... so to clarify, my phone has not been unlocked from AT&T and I am assuming I should still be able to get this stuff working.
Thanks again!
Gas Addict said:
Hi arexben,
I actually was an idiot and soft reset after unplugging and then plugging in the USB and not seeing any change on the screen.
Now if I put JumpSPL on my PDA and try to run it, it won't run saying it can't be opened because its either not signed w/ a trusted certificate or one of its components cannot be found.
Thank you so much for everyone trying to help me ... so to clarify, my phone has not been unlocked from AT&T and I am assuming I should still be able to get this stuff working.
Thanks again!
Click to expand...
Click to collapse
Not sure, but try to install the sdkcerts first.
Download them here: http://www.cinetsystems.com/xda/Kaiser Cab Collections/SdkCerts.cab
bmueller77 said:
Not sure, but try to install the sdkcerts first.
Download them here: http://www.cinetsystems.com/xda/Kaiser Cab Collections/SdkCerts.cab
Click to expand...
Click to collapse
Installed the SdkCerts then tried running JumpSPL off the phone still can't run that program.
Any other ideas guys?
Thank you again!
OK
I've always had troubles flashing radios for some reason, I've managed to just not do it but now with Duttys 6.1 out I really need some help
- I've flashed Duttys latest successfully
- I've flashed HardSPL
- But whenever I flash the radio (1.64.08.21) I get a connection error at 99%!!
Now I can still get into the phone using mtty and the boot command.
Am I doing something stupid -- Any help gratefully received!
Alex
ps - I have a UK o2 XDA Stellar
I'm a newbie been here with a AT&T Tilt less than a week and I promise I'm reading, but I'm having the exact same problem. Flashed Duttys dual V4 as my first try last Tuesday without a problem and of course be a crazy new guy I wanted his newest work. So I flashed Duttys 6.1 today and I guess I just can't figure out how to flash radios, because I've tried 2 now and both error out at 99% and I too have to use mtty to get back into the phone. I'll keep reading, but if someone could tell us new guys what the heck we are doing wrong that would be great.
PS I'm glad to be here and this looks like a lot on fun thanks for having me and look forward to helping out someday.
JMan
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
First, are you using a 6.0 rom or a 6.1 rom? If you are using a 6.0 rom you cannot flash any of the 6.1 radios and vice versa. Also, if you have hardspl installed, why would you need to use jumpspl. I have never used jumpspl and I promise I have flashed 50+ times counting, roms, radios and splash screens.
I believe that was my problem, I was never able to get Hard-spl installed and I was using jumpspl to install the 2 roms that I have installed since I got my tilt a week ago. The method I used above allowed me to get hard-spl installed and then I was able to install the radio rom. I am using Duttys WM6.1 rom.
JMan I want your babies!!!
Ok I had actually done everything upto the final step (holding the camera button after a soft reset) but that made it possible to flash the radio just as you described.
So many thanks for sharing your solution!!
Alex
jmandss said:
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
Click to expand...
Click to collapse
You are the STAR! Trillions of thanks. Solve my problem!!!
I love it when when the new guy can help out! Glad it worked guys, and thanks to all the old pros around here for allowing us to read so we can try and help ourselves out.
Take care,
JMan
I think I have fallen in love with this thread. This is truly nice to see guys. Keep up the great work.
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
please help me
I don't want to miss mi tytn
pedro_se_rooot said:
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
Click to expand...
Click to collapse
You need to use MTTY to get things going for you again, here is the thread to get mtty:
http://forum.xda-developers.com/showthread.php?t=371154&highlight=mtty
Search around and see if you can find the step by step to use it, might even be a how to text file in the zip file not sure. This should get you back on your way.
Can someone locate the step by step to use mtty for this man and put it in this post?
Have a good one,
JMan
Not a good day for the Wolfpack, Damn Tarheels!!
Hi everybody,
i got a XDA Orbit 2 and today i tried to install SPB Phone Suite.
During install it asked for a Softreset, which i did...
After that i refused to boot and keeps hanging at the o2 Bootscreen.
It totally freezes, regardless if i pull any cable, remove the sd-card etc..
So i thought i'd a hardreset once again, but that one didnt work at all.
The Restore lasts maybe 10 secs (with and without sc-card), then asks for another boot and im again where i startet, the o2 bootscreen.
Any chance i get it working again?
Like somebody else recommended flashing it with either another rom or the original one, which i might d/l somewhere.
Then again, any Flash-HowTo starts with an ActiveSync Connection.
Since my Device wont boot at all, the ActiveSync Connection wont be established...
Any helpful Advise highly appreciated :-/
regards...
You should be able to manually put it into the boot loader. I'm not familiar with you phone so you will need to research that.
***Update**** Try this; "turn your phone on press and hold the two buttons on the upper left and right side from your naviwheel and press the resetbutton with your stylus"
http://forum.xda-developers.com/showthread.php?t=366303
hrm, pressing the upper left/right buttons and reseting it doesnt do anything.
regarding google im the first human ever trying to get the htc touch cruise into bootloader mode.
i keep researching, thx for ur effort tho
Manually getting into the boot loader will allow to establish a link to your PC in order to re-flash. Like I said, I'm not familiar with your phone....
yup, i noticed some more users here own an Orbit2.
So i hope somebody is able to enlighten me, before i brake my fingers while trying to press all buttons same time and then somehow hit the reset button, hehe.
ok, i managed to get into bootloader.
some more detailed research helped me there, actually inside this board :-/
now lets see if HardSPL makes me happy.
tx again for ur time
I have an Orbit 2,
To Hard reset and delete everything from your phone and then let the rom reload everything back to factory settings, do the following.
1. Remove SD card
2. Hold down the 'Windows Icon' Button and the 'OK' button at the same time and keep them held in.
3. While still holding in the above 2 buttons, use the stylus and press the reset button in and then release it but you must still keep the 'Windows' button and the 'OK' button still in until you are prompted with a menu.
4. Once the menu appears: press 'Send' button to reset and reload rom or any other button to cancel.
I have done this procedure a few times now and is quite safe, especially after loading a crap piece of software that totally knackers up my Orbit 2.
I hope this helps you out........
Good luck
Tried that before and it worked out before also.
This Time the complete recover-process lasts only 10 seconds and then the Boot doesnt work anymore either.
Dunno why the hardreset aint working anymore.
Regarding the Flashing:
I managed to get into Bootloader and see the following Information:
POLA200
SPL-1.25.0000
CPLD-2
Serial.
Then i plug in the USB-Cable and start the Update-Utility.
After following each step i get the following error:
Error 262: Update Error
Saying it has encountered communication Errors and asks me if i want to recover...
Im running VistaSP1, maybe thats a reason?
Try this for your Vista issue. It worked for me the first time. Although I don't know if SP1 has any effect.
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27 This was for Hermes also....
Updating the USB-Driver didnt help .
Using a XP VirtualPC didnt work out either, hehe.
Ill try tomorrow on a XP Machine, thanks for ur time once more.
Im not that desperate anymore, hehe.
Damn, now im using a Windows XP Machine (incl. all Updates) with ActiveSync 4.5, and still get the [262] Update Error.
Seems its seriously damaged :-(
One Question:
Did you installl phone-suite on a cooked rom, or on the original o2 rom?
i got the same freezing problem on my touch with a cooked rom. with the original rom i got no problems.
..
ploep said:
Hi everybody,
i got a XDA Orbit 2 and today i tried to install SPB Phone Suite.
During install it asked for a Softreset, which i did...
After that i refused to boot and keeps hanging at the o2 Bootscreen.
It totally freezes, regardless if i pull any cable, remove the sd-card etc..
So i thought i'd a hardreset once again, but that one didnt work at all.
The Restore lasts maybe 10 secs (with and without sc-card), then asks for another boot and im again where i startet, the o2 bootscreen.
Any chance i get it working again?
Like somebody else recommended flashing it with either another rom or the original one, which i might d/l somewhere.
Then again, any Flash-HowTo starts with an ActiveSync Connection.
Since my Device wont boot at all, the ActiveSync Connection wont be established...
Any helpful Advise highly appreciated :-/
regards...
Click to expand...
Click to collapse
how did you get it in to boodloader mode please
HTC Touch Cruise ROM on O2 Orbit 2
Hi,
Sorry for posting on this thread which might be the wrong place but hope someone ccan help.
Can I install an HTC Cruise ROM (WM 6.1 from HTC website) on my Orbit 2 ?
so i thought it'd be a easy thing to do but i guess not.
first i couldn't get RaphaelHardSPL-Unsigned_1_90_3.zip to work so i used SSPLManual to get it to go, now no matter what i do it gets to 0% and the pocket pc locks up. im using a HTC Touch Pro with Sprint. the device says Upgrade ROM code error please try again. ms activesync says that it cannot recognize the device or something, and the hardspl program says error 262. ive been searching and reading for an hour and a half and cant figure it out. i really need my device to work by like, tomorrow, so please help me out guys :\
Try going to bootloader mode and flashing the stock ROM that came with it.
i held down the power and volume down buttons and reset it but it just goes to the tri colored screen everytime. there has to be something im just completely missing. to reset to stock rom i would just put the rom on a memory card or how ever the website instructions say to do it and put it in the phone and restart or how does that work
Exactly (if you want to flash the memory card way). Or you can simply connect the device through activesync when in bootloader and flash the stock ROM (download it if you don't already have it).
jirobinson13300 said:
so i thought it'd be a easy thing to do but i guess not.
first i couldn't get RaphaelHardSPL-Unsigned_1_90_3.zip to work so i used SSPLManual to get it to go, now no matter what i do it gets to 0% and the pocket pc locks up. im using a HTC Touch Pro with Sprint. the device says Upgrade ROM code error please try again. ms activesync says that it cannot recognize the device or something, and the hardspl program says error 262. ive been searching and reading for an hour and a half and cant figure it out. i really need my device to work by like, tomorrow, so please help me out guys :\
Click to expand...
Click to collapse
Isn't the Sprint CDMA? The GSM HardSPL won't work. From the bootloader screen flash it with an OEM Sprint ROM. Good luck