Related
Hello everyone,
I'm totally lost in this WM6 upgrade.
I've tried everything but i wont get my MDA Vario to flash with WM6.
My MDA Vario is unlocked (sim and CID) but i can't flash it because of my SPL 2.21????
This is what i have done:
installed button's 1.05 ROM
Download & installed lokiwiz - HTC Wizard Unlocker UPDATE Version 0.2b.
But stil my SPL is at 2.21.
Can someone please help me out here??
Thanks in advance!
Regards,
Schmia
Both your IPL and your SPL must be 2.xx and higher. After you flashed to Buttons rom. did you reflash to a higher version after after you unlocked and cid unlocked your phone to make sure both IPL and SPL were 2.xx or higher?
I've followed the tutorial:
16. Watch the rebooting of your PDA, if BOTH IPL and SPL are 1.xx then great. Quite probably your IPL will be 1.xx and your SPL will be 2.xx. Rerun the button 1.05 ROM downgrade a second time and it will become 1.x on both IPL and SPL. You don't need to redo the unlocking.
17. My suggestion, take for what it's worth, is to download and install the T-Mobile 2.26 ROM
This will give you a strong 2.26 IPL and SPL to work with.
My IPL was 1.XX after the 1.05 downgrade, but my SPL was still 2.21 even after the rerun.
I have tried to instal T-Mobile 2.26 rom, but it gave an error.
check if you have G3 or G4 unit
I have a 3G device.
Is there nobody who can help me???
schmia said:
Is there nobody who can help me???
Click to expand...
Click to collapse
I think that you haven't unlocked the phone properly. Read Dr. P's tutorial about unlocking G3 phones.
Kirby
if your ipl is 1.05 and your spl is still 2.21...then you need to reflash again so that both ipl and spl are 1.05 before you can proceed. ipl and spl should never be different.
WHen you downgrade to the Button rom, in most cases the IPL will change, but the SPL will not. You then have to downgrade again to get the SPL to get to 1.xx . There have been some cases reported where it takes reflahsing the button rom many times (like 8 times or somesuch) before the SPL will finally come down, but you have to complete this step or you will not be CID Unlocked.
Make sure you have your SD card out when you are flashing as this can cause problems.
Good luck, and sorry, but for those that have run into the stuck SPL there hasn't been a real solution other than keep flashing the button rom until it drops down to 1.xx. After that then the CID unlock will be complete and you can then flash the T-Mobile 2.26 rom (or whatever other 2.xx rom you want).
mfrazzz said:
WHen you downgrade to the Button rom, in most cases the IPL will change, but the SPL will not. You then have to downgrade again to get the SPL to get to 1.xx . There have been some cases reported where it takes reflahsing the button rom many times (like 8 times or somesuch) before the SPL will finally come down, but you have to complete this step or you will not be CID Unlocked.
Make sure you have your SD card out when you are flashing as this can cause problems.
Good luck, and sorry, but for those that have run into the stuck SPL there hasn't been a real solution other than keep flashing the button rom until it drops down to 1.xx. After that then the CID unlock will be complete and you can then flash the T-Mobile 2.26 rom (or whatever other 2.xx rom you want).
Click to expand...
Click to collapse
This should be added to the tutorials about Unlocking & Rom Upgrading.
And this quote also.
"if your ipl is 1.05 and your spl is still 2.21...then you need to reflash again so that both ipl and spl are 1.05 before you can proceed. ipl and spl should never be different."
Cing 8125 said:
This should be added to the tutorials about Unlocking & Rom Upgrading.
And this quote also.
"if your ipl is 1.05 and your spl is still 2.21...then you need to reflash again so that both ipl and spl are 1.05 before you can proceed. ipl and spl should never be different."
Click to expand...
Click to collapse
The Dr. P tutorial specifically says this (just not in those words). It tells you (after the last lokiwiz) to watch your screen and that you most likely will still have an SPL of 2.xx and will need to reflash (most people just don't read this and try to move on). The part of about having to reflash numerous times is new though. I've only heard of it a few times, but if you look at the posts from a month or so agao in the Dr P thread on unlocking you'll see where a few people ran into it and it took numerous flashes to finally get SPL to go to 1.xx.
before wm6 roms, every time there was a new rom for wm5 (molski or faria) you'd always get people in the thread mentioning that their ipl and spl are different. in those threads, the advice has always been to reflash a few extra times too. (I personally haven't had any problems with this...but i think i started my unlocking on a 1.8 us t-mobile rom with xelencin's rom...which had an unlocker built into the rom update package).
anyway, the phone's not bricked or anything, so you just have to keep flashing to get it working...
xelencin's rom (the first rom I ever flashed...)
http://forum.xda-developers.com/showthread.php?t=274205&highlight=xelencin
monkey_knight said:
if your ipl is 1.05 and your spl is still 2.21...then you need to reflash again so that both ipl and spl are 1.05 before you can proceed. ipl and spl should never be different.
Click to expand...
Click to collapse
I've re-flashed 3 times but if i understand correct, than i have to retry flashing until SPL and IPL are the same?
Regards,
Schmia
schmia said:
I've re-flashed 3 times but if i understand correct, than i have to retry flashing until SPL and IPL are the same?
Regards,
Schmia
Click to expand...
Click to collapse
yes. ipl and spl should both drop to 1.05. at that point you can go through the unlock and flash back up.
Thanks Guys!!!
With all your good advise, i finally have my MDA Vario flashed with a WM6 rom (TNT 2.0 Professional)
I'm really greatfull to you!
Now i have to find out what WM6 rom is the best for me.
Regards,
Schmia
I'll try to make the long story short… Here is the situation:
Cingular 8125 G3, IPL and SPL originally 2.5x, SIM and CID unlocked. I wanted to update my device to WM6 so tried to update to T-Mobile 2.6 to get 2.6x SPL but update gave me "wrong nfk" error. I used 3.08 IPL/SPL update which result Cingular 2.5.xx OS and 3.08 IPL/SPL- all fine so far. Tried to flash the XM6r4 rom but update freeze at 99%. I restarted my Wizard and now I'm on 3.08 IPL/SPL boot loader screen, tried again to update to XM6r4 ROM and again freeze at 99%. I restarted my Wizard and had no choice then flashing the love ROM. Wizard loads ok after flashing the Love ROM, IPL is 1.05, SPL is 3.08. Tried to flash nbd.v7.9 (WM6) ROM. The ROM flashed OK, but after restart I'm on the same state- Love ROM loaded, IPL is 1.05, SPL is 3.08 NO WM6…
How can I get WM6 on my device?
Any help would be appreciated!
Start by following the unlocking tutorials.
Thanks for your help
After some reading I found out that my device was not CID unlocked, this was the main issue. I downgraded to IPL 1.05 again then CID unlocked it. I have WM6 running right now. Thanks again!
I'm triying to make UPGRADE with differents ROM but when the process finish i stell having the same OS WM5 from Tmobile, i did downgrade with botton downgrade rom i used LOKIWIZZ but ever happen the same, what i doing wrong?
ISPL 3.08
SPL 3.08
You should be more detailed in explaining things.
First Try to tell us step by step what errors are you getting.
On the signature you say ipl/spl 3.08 (it should mean you're cid unlocked).
So please describe the update rom process better
OK First I had IPL 2.26 and SPL 2.26 with TMOBILE wizard ROM I tryed to update to to WM6 HTC Professional + Home, everything in the process look in order, pass to 99 % in the Progress BAR and wait several minutes and i get again the tmobile ROM the same one, so read several post and I dicide to downgrade with Wizard Button ROM, and it was succesefully, I was in that moment ipl 1.05 something else and SPL 2.26, so I used, so I upgrade to the TMOBILE wizard ROM, and I get IPL 2.26 and SPL 2.26 and I'm tryed again to made a new UPGRade with the same ROM WM6 HTC Professional + Home and it was the same results again, so I made the UPGRADE with the IPS_SPL 3.08 File and now I m in this point now. So what i must do?
Downgrade IPL and SPL does not mean you have CID unlocked your phone. You need to use lokwiz02 to unlocked it when IPL is 1.01. Then first upgrade IPL to 2.2x / 3.08, after that you can proceed to upgrade WM6.
All instructions and links are in stickes.
hello all and thanks for the help
i have a g3 kjam after flowing the 3 steps
1.installing the rom that downgrade the ipl to 1.00
2.cid unlock
3.installing the rom that changes ipl/spl tp 3.08
any rom that i try to install finshes 100% succsesful
but still boot a wm5 rom with a new icon when starts
any help will be great
thanks
I thought you need a solid 2.xx rom to flash a new rom ??
Personally, I went from button 1.05 rom to TMobile 2.26 rom to new WM6 rom.
I flashed 3.08 later - as is does not change the O/S - only IPL/SPL. Did not find any benefit to it, so went back down to 2.26
Please note that there are freezing issues if you flash down from 3.08 to 1.05. Apparently the spl can freeze if you do this - and that is a problem. So, to play it safe - do not do that - thanks.
It is always recommended that you flash a solid 2.xx rom such as the TMobile one when going between the different WM6 roms available here - you may want to try that - go down to 2.xx, then upgrade to WM6
thats very good to know i'm actualy in a freeze spl is on 3.08
any idea hwo to downgrade?
I've attached a link to another thread about the freezing issue. Unfortunately, it does not give the answer as to how to fix it. But - should no one else answer on this - I would recommend that you send a private message to senior user "mestrini", and hopefully he can walk you through it.
http://forum.xda-developers.com/showthread.php?t=377038
I got my info from him as per the attached post. I do not have enough experience as to why it freezes - or how to fix it.
Good luck
Well,after downgrading to 1.xx and CID unlocking,its essential to upgrade to ipl/spl 2.xx for upgrade to wm6,its highly recommended to upgrade to 2.xx by flashing the T-mobile 2.26 for a solid base,but,however, you can still even upgrade to wm6 with ipl/spl 3.08.Wm6 works on 2.xx and 3.xx.
DGman
I believe your phone is still CID locked,you didn't do the CID unlock method correctly,but you upgraded to ipl/spl 3.08,now you can only CID unlock your phone by downgrading to 1.xx. Yes! SPL freezes if you downgrade to 1.xx from 3.08.So always first downgrade to 2.xx and then to 1.xx.Now I'll advise you to upgrade to IPL/SPL 3.08 again and then try to downgrade to 2.xx by flashing the T-mobile or Wizard_love Rom or official stock Rom of your carrier if other then T-mobile.If succeed to downgrade to 2.xx,only then flash Button's Rom 1.05 to get to 1.xx and apply the lokiwiz02b to CID unlock the phone.After that upgrade to 2.xx by flashing T-mobile 2.26 and upgrade to any wm6 Rom.
Cheers!
thanks for tring but device doesn't let me downgrade to 2.26 or any other 2.xx ipl/spl only stright down to 1.xx and like you said spl freeze on 3.08
when i tried wizard love it did the rom flash but still ipl/spl 3.08
i'll try to find my 2.xx official rom
Hi guys.
I have this iMate Kjam (Not mine). It was with a T Mobile Official ROM and has IPL/SPL at v2.26. I checked and there was no G4 sign anywhere. Someone had to remove the CID thing to this. I downloaded several WM6 ROMs but once the complete flashing and the device reboots, I'm still in the T-Mobile ROM. I down-flashed to the age-old Button Love WM5 base ROM and here is the ROM status:
IPL: 1.01
SPL: 2.26
GSM: 1.12.10
OS: 1.5.4.2
If I upgrade from this point with, let's say, TNT5.0, here is what happens:
IPL: 1.01
SPL: 2.26
GSM: 1.12.10
OS: 1.5.4.2
Same right? but all the graphics change when booting. There is the HTC logo when device is turned on and there is the TNT 5.0 "BOOM" title when OS is loading (with the IPL/SPL/GSM/Radio)
Can someone tell me what is going on? HardSPL (http://forum.xda-developers.com/showthread.php?t=332320) clearly tells me that device is NOT G4
Doomer D. Great said:
Hi guys.
I have this iMate Kjam (Not mine). It was with a T Mobile Official ROM and has IPL/SPL at v2.26. I checked and there was no G4 sign anywhere. Someone had to remove the CID thing to this. I downloaded several WM6 ROMs but once the complete flashing and the device reboots, I'm still in the T-Mobile ROM. I down-flashed to the age-old Button Love WM5 base ROM and here is the ROM status:
IPL: 1.01
SPL: 2.26
GSM: 1.12.10
OS: 1.5.4.2
If I upgrade from this point with, let's say, TNT5.0, here is what happens:
IPL: 1.01
SPL: 2.26
GSM: 1.12.10
OS: 1.5.4.2
Same right? but all the graphics change when booting. There is the HTC logo when device is turned on and there is the TNT 5.0 "BOOM" title when OS is loading (with the IPL/SPL/GSM/Radio)
Can someone tell me what is going on? HardSPL (http://forum.xda-developers.com/showthread.php?t=332320) clearly tells me that device is NOT G4
Click to expand...
Click to collapse
Update:
I was able to install the official T-Mobile ROM onto Button Love ROM. Here is the screen statistics:
IPL: 2.26
SPL: 2.26
GSM: 02.25.11
OS: 2.26.10.2
If I try to upgrade to WM6 now, nothing will happen as I've already tried. After the flash process, it will still be official TMobile...
What should I do now? If I compare the properties of this Wizard with my own, I'm pretty sure this should be a G4 device.
Flash Buttons ROM again and do a CID unlock. That's it! Have fun!
I have a G3, but I had to flash Button twice so that the IPL/SPL matched, then I unlocked and reflashed 2.26 stock (again be sure that IPL/SPL match numbers), then from there I joined rom flashers anonymous!
akashastrega said:
I have a G3, but I had to flash Button twice so that the IPL/SPL matched, then I unlocked and reflashed 2.26 stock (again be sure that IPL/SPL match numbers), then from there I joined rom flashers anonymous!
Click to expand...
Click to collapse
Trying the Button Love ROM the third time... the SPL just won't drop... whats going on?
Cyberdyne said:
Flash Buttons ROM again and do a CID unlock. That's it! Have fun!
Click to expand...
Click to collapse
The only avaliable HardSPL tool doesn't recognize the device as G4... so how do I forced CID unlock? I tried SoftSPL... but at that time, my IPL and SPL were different...
Lets face the situation
IF you have
IPL 2.26 or 1.xx
SPL 2.26 or 2.XX
You have a G3 device - forget do not use Hard SPL or Soft SPL, these are ONLY FOR G4 DEVICES
Since you have a G3 Device you have 2 options
If you have IPL 1.xx and SPL 2.xx . use WST (Wizard Service Tools) to unlock your CID device
http://forum.xda-developers.com/showthread.php?t=329170
Note that only with IPL 1.xx you are hable to unlock your CID with WST
If you have IPL 2.xx and SPL 2.xx, than you must downgrade both to IPL/SPL 1.xx with an official ROM
Before you do something, install WST in you PC, and check the real situation of your device
Pisca said:
Lets face the situation
IF you have
IPL 2.26 or 1.xx
SPL 2.26 or 2.XX
You have a G3 device - forget do not use Hard SPL or Soft SPL, these are ONLY FOR G4 DEVICES
Since you have a G3 Device you have 2 options
If you have IPL 1.xx and SPL 2.xx . use WST (Wizard Service Tools) to unlock your CID device
http://forum.xda-developers.com/showthread.php?t=329170
Note that only with IPL 1.xx you are hable to unlock your CID with WST
If you have IPL 2.xx and SPL 2.xx, than you must downgrade both to IPL/SPL 1.xx with an official ROM
Before you do something, install WST in you PC, and check the real situation of your device
Click to expand...
Click to collapse
Excellent.
If I'm on Button Love ROM, I have IPL v1.x ad SPL v2.x
Should I upgrade to WM6 from here?
If not, then I have to upgrade to Officia T-Mobile ROm. Then IPL/SPL = v2.26 but WM6 won't flash...
Ah ! c'mon guys
Give this guy a break.
Doomer D. Great
Go read and fully undrstand this guide to CID unlock your phone and upgrade.
BTW,its a G3 phone you got there,forget anything about G4,you are only concern shud be regarding G3 device.
Doomer D. Great
Go read and fully undrstand this guide to CID unlock your phone and upgrade.
BTW,its a G3 phone you got there,forget anything about G4,you are only concern shud be regarding G3 device.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
zabardast_1 said:
Doomer D. Great
Go read and fully undrstand this guide to CID unlock your phone and upgrade.
BTW,its a G3 phone you got there,forget anything about G4,you are only concern shud be regarding G3 device.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
Click to expand...
Click to collapse
Actually, I followed what Pisca said about using WT and it worked... in Button Love, I finally CID unlocked and upgraded to Official TMobile. Then TNT5.0. All Well
Thank you very much!
Problem solved
Doomer D. Great said:
Excellent.
If I'm on Button Love ROM, I have IPL v1.x ad SPL v2.x
Should I upgrade to WM6 from here?
If not, then I have to upgrade to Officia T-Mobile ROm. Then IPL/SPL = v2.26 but WM6 won't flash...
Click to expand...
Click to collapse
Ok, if you are on IPL 1.xx and SPL 2.xx, you can use WST-Wizard Service Tool 4.2.2 to CID unlock
Then you should load a carrier ROm T-Mobile to get IPL/SPL 2.xx
But allways read as mentioned in the previous post
Doomer D. Great said:
Actually, I followed what Pisca said about using WT and it worked... in Button Love, I finally CID unlocked and upgraded to Official TMobile. Then TNT5.0. All Well
Thank you very much!
Problem solved
Click to expand...
Click to collapse
Great forget my last post