Hi guys,
I've recently become the proud owner of a vodafone touch pro. However when connecting to wifi, opera etc will not find any webpages. Now i know my wifi is working and the phone connects fine and picks up the DHCP ip address.
What could I be doing wrong? I've noticed data connections is disabled but I believe this is just for GPRS etc? Either way how can I confirm my wifi connection is being used?
Many thanks
EDIT - NM it was because it was not set to work
Hi Scribe,
I had the same problem as yours. No solution so far. Had no problem with GPRS.
I have mine working good on either wifi or GPRS.
Probably it's wifi problem? Have you tried on another wifi connection?
what was not set to work?
I have the same issue, connects to wifi but no internet. laptop connects and browses fine, but touch pro (and also diamond) don't
Make sure when you set your wifi connection up you say that it is used to connect to work not the internet, also make sure your adapter settings say this.
The problem is that the phone will always default to GPRS/3G for the internet but if it senses a local work network it will use that first.
Stupid I know!
I have the same prob, I changed some settings and it works. Try change Authentication to Shared instead of WAP-PSK, Data Encryption to WEP instead of TKIP. After you have internet connection, you can change to previous wifi settings with same network key.
Mine has gone again! I swear it's because 'Connects to the internet' wont save in the proxy settings - nope not that and still wont work, I've also tried by disabling all security
Related
My TouchPro can connect normally to unsecured wifi networks, but with WPA encrypted ones, it can only connect for the first time, after that it can not.
At home I have a wireless router/ADSL modem (Zoom X6) that is connected to my PC by cable, all my phones and laptops connect to internet via wifi. While other phones (1G iPhone) and laptops always connect successfully, the TP only connected once and then cannot or unable connect to the WPA security-enabled wireless network (although it's able to scan and detect the availability of the Wifi network). I tried to reset the router settings, even update router firmware, but no luck, it's still unable connect. I also tried with my office secured wifi network and I had the same problem.
Yesterday, I had to hardreset my TP and tried to connect once again, but problem was repeated, connected only once and after that, unable. Note that my previous PPC (TMobile Ameo WM5) didn't have any problem with the same wifi router and the same wifi settings (as follow).
My TP wifi settings:
Network Name: MyNetwork
Connects To: The Internet
Uncheck "This is a hidden network"
Next step:
Authentification: WPA-PSK
Data Encryption: TKIP
Greyed Out: The key is automatically provided
Network Key:************** (my pass)
Greyed Out: Key Index: 1
Next,
Checked "Use IEEE 802.1x network access control" but greyed (I can't change this)
Anybody know the solution for this issue?
Thanks and very appreciated for any help.
i experienced similar problems with my old p4350 but not yet with the TP...
no solution, sorry. but im quite unhappy that this issue still exists...
Any suggestion, pls.
yeah.. quite sucky.. I though the WiFi 'broke'.. but i was able to connect to a WEP site.. I think its something to do with WPA.
I never had this problem with my Diamond. The firmware on Diamond isso much more stable compared to Touch Pro..
I set everything to WEP and my key is open instead of shared, and now it works fine.
I had issues at my dad's, who has no encryption, and also there, when I set the key to open io shared, I got connection. (even though there is no key
anyway, it looks like that is the bug (at least in my device)
I have exactly same settings and same problem... but I want to use this encrypted connection since in future I will have to connect also in other places where I need it for sure.
Any help here?
I have similar promblem with my Hermes before.
My wireless router is running "Turbo-G" mode, my Hermes can't connect it with Turbo-G mode On.
After I change the wirless mode from Turbo-G to "g/b", my Hermes can connect it without any problem.
I tryed that and does not work...
strange is that is was working in the past and on router I did no changes but on TP I installed just some apps which should not affect this...
Only what could affect is Advanced config which I installed...
So where else can be problem?
How can I troubleshoot this?
Signal kvality is good but still keeps dropping and does not obtain IP from router.
mine works fine...not that that helps you in any way
I found the solution: set router to unsecured and use MAC filter. But that is only a tip, because my TP still can not connect with any other secured wifi.
I had same problem and looks like I found the bug in Advanced Config 3.2
There is in Network -> WPA auth... was enabled and I put Disabled (now I can use WPA auth anyway... before it just could not connect)
And next Wi-Fi delay after boot: 0 (when I changed to other number than I got problem that I could not even see any AP as I could see before and only network card settings was shown)
Try to play with other settings and you will see... I had also errors with device.exe after reboot... but now it all works as it should.
Just post here if it helps you also so we can notify creator of Advanced Config...
hung_ng said:
I found the solution: set router to unsecured and use MAC filter. But that is only a tip, because my TP still can not connect with any other secured wifi.
Click to expand...
Click to collapse
You are merely restricting people from connecting to your router.. without encryption, you are sending unsecure packets all over..
Have you tried using AES encryption on your device instead of TKIP? I only mention this because TKIP is the only one I haven't tried. All other methods of connectivity work fine for me with the TP.
I tried the PT using unsecured routers, WEP and WPA and all of them worked fine with stable connectivity.
The routers I have tried (without any problems) so far are:
1. Linksys WRT-54G running Tomato firmware
2. Linksys WRT-54G running DD-WRT firmware
3. D-Link DIR-655 running latest firmware
I tired open, WEP and WPA1+2 on all of the above routers and the TP responded with zero issues...
I am not using a custom ROM.
I hope this helps in some miniscule way.
Good luck.
Minus-1 said:
Have you tried using AES encryption on your device instead of TKIP? I only mention this because TKIP is the only one I haven't tried. All other methods of connectivity work fine for me with the TP.
....
I tired open, WEP and WPA1+2 on all of the above routers and the TP responded with zero issues....
Click to expand...
Click to collapse
I was about to say the same thing...
Not having any issues with my girlfriends WPA secured router. It's on WPA2-PSK and AES encryption. Enter key first time (case sensitive!!), and of you go... Connecting without trouble ever since
hmm..Funny mine still can't connect to my home WPA2, AES or TKIP.. I'm on the Buffalo Tomato firmware..
WIFI not connecting
This solution worked for me!! Excellent. This was a right pain!
thedino said:
I had same problem and looks like I found the bug in Advanced Config 3.2
There is in Network -> WPA auth... was enabled and I put Disabled (now I can use WPA auth anyway... before it just could not connect)
And next Wi-Fi delay after boot: 0 (when I changed to other number than I got problem that I could not even see any AP as I could see before and only network card settings was shown)
Try to play with other settings and you will see... I had also errors with device.exe after reboot... but now it all works as it should.
Just post here if it helps you also so we can notify creator of Advanced Config...
Click to expand...
Click to collapse
I've got the sollution, everybody on this forum probably has advance config installed, the program sets some default value's of it's own, set the WPA authentication under network in the advance config program to disabled and it will work again. Anyways, that worked for me
I've removed WiFi settings and then I edited settings again. It works now
Raphael Wifi problems
I bought this Fuze to replace my trusty Dash since I broke the antenna on my Dash. I'm running NRG Magic, but have tried other NATF and other ROMs as well, I cannot get this phone to connect to my wifi network I'm using WPA2-PSK but have disabled security for testing. My Dash and my laptop connect immediately with no problems. If I cannot get wifi going on this Fuze I'm afraid I'll have to put it on Ebay and try the Iphone, which people seem to love.
The Fuze did connect once, and it was WPA2-PSK at the time, I don't remember what ROM I was using at the time probably an NRG flavor, but Ihave had _no_ luck since.
Should I flash to 'official' ROM? Honestly I'm getting tired of playing with this thing I don't have the time.
Any help would be appreciated.
Thanks,
Marc
I may have found something
Check your time zone/daylight savings settings on your router. Phone and router time must be in sync.
-Does anyone know how to priotize w-lan for internet connections?
It seem that my phone always uses the mobile connections (GSM, 3G etc).
In menu for connections where internet connections can be created, I can't find anyting about w-lan.
This is something I've been meaning to ask about while I wait for the Fuze. By way of background, I have a Cingular 8525 with the original (WM5) ROM, and it drives me nuts using it at home. I only get EDGE inside my house, but the stupid phone persists in making an EDGE data connection instead of using the nice, fast Wifi connection that I just enabled. I use NoData to make sure it doesn't connect via EDGE or 3G, and then half the time it says it says that it can't connect -- even though the icon says that it is connected!! The only way I can reliably connect via Wifi is to go briefly into and out of flight mode, then turn on Wifi before connecting.
I'm really, really hoping that the situation is better with the Touch Pro/Fuze. Can anyone reassure me on that?
it should be accessing wifi first by default i believe...unless other connection is already connected
Hello!
Start first the WiFi Connection and then the Internet Explorer or Opera.
pjo12345
There's this stupid thing with wlan connections in WM - if connection type is set to 'Work', you can browse through files on other computers in (W)LAN at home, but any Internet connection wll be realised through GRPS/3G. To make it connect to the Internet using WiFi, you need to switch wifi type back to 'Internet'.
Maybe that's the thing?
Is there a way how to setup that the WiFi is connected to both (work AND internet)? I never saw WiFi connected only to work network... I assume there is no way but why not to ask ;-)
I know that many others have problem with that, but I didn't find any solution yet...
Because when I set it as work, my Exchange sync is working but no Internet, and when I switch to Internet, opera and QuickpGPS is working, but no Exchange sync (it is trying to open VPN connection because I need to go though inside address to the server because certificates and of course it cannot get it). Or I need somehow set that no VPN will be dealed on this WiFi network...
I need something like BOTH or Auto option.
It seems to be switching from Wlan to G / 3G / H when the signal is not that great. Mostly with the weather tab and Opera. Quick GPS works fine. The way I make sure it is on the internet through wlan is to shutdown the telephone and keep the wlan on with comm manager. The disadvantage is that anyone calling will be heading to your voicemail. Another option is to use the "Nodata" program, en disable to internet connections.
On Touch Pro, I usually just go to COMM MANAGER and switch on wifi and switch off data connection. It is only a couple of quick steps and saves battery, since you don't need both on, if you only want to use wifi.
I am sure there must be a more seamless solution, but I like easy fixes.
wmm said:
I'm really, really hoping that the situation is better with the Touch Pro/Fuze. Can anyone reassure me on that?
Click to expand...
Click to collapse
No it is not better. Turning on WiFi is not enough. It will continue to use the cellular data connection until you manually turn it off. This wouldn't be so bad, but in my experience I've had to push the button to turn off the cellular connection multiple times before it would actually do so. What would be really nice is if WM could seamlessly switch from the cellular network to WiFi, with zero user interaction, just like the iPhone does.
I got an other problem with wifi. When I establish a wifi-connection and pull my mail the ppc still connect with a data-canection and didn't use the wifi. My kaiser used the wifi-connection for that.
8notime said:
No it is not better. Turning on WiFi is not enough. It will continue to use the cellular data connection until you manually turn it off. This wouldn't be so bad, but in my experience I've had to push the button to turn off the cellular connection multiple times before it would actually do so. What would be really nice is if WM could seamlessly switch from the cellular network to WiFi, with zero user interaction, just like the iPhone does.
Click to expand...
Click to collapse
I wrote the original post before I had a chance to try it for myself. I've had a Fuze for three weeks now, and it works fine for me. I turn on wifi and the Fuze uses wifi. I turn it off and it goes back to normal wireless. (I did do the registry edits to turn on the HSDPA stuff in the connections tab and enabled the modified connection icons in the menu bar. I don't know if that had any effect on this issue or not, but it does what I would expect now.)
My VOX has stopped communicating to my router. This appears to have happened since I accidently deleted profile but that could be co-incidence..
It sees my network...
Settings VOX
Net type INTERNET
Auth WPA 2
AES
USE IEEE 802.1x YES
AEP type: Smart Card or certificate
Settings WAG200G nothing really relevent here except to say AES as above.
My phone seems to connect WITHOUT encryption but when I add encryption (with real simple password) this is where the phone can't connect for some reason... My laptop is still connected to the router without any problems there is no MAC filter or anything like that.
Anyone please help!
BTW tried hard reset not helped.
i have the exactly same problem. i tried other kinds of config on my router but nothing worked.without encripton or password it connects...
Not connecting to WIFI
Seems more people have this problem?
WPA2 does seem to be a problem. Personally I also use fixed IP, but never got my phone connected to my home network.
@work I use WEP and DHCP, no problem connecting.
@home I use, as mentioned, WPA2, AES, Fixed IP, router.
If anybody got a simple answer...?
btw, I got this problem after using other roms(for almost a year now). Basic HTC rom (WM 6.0 :-( ) seems to work fine.
Half connected in fact
Hi, I'm also getting a wifi problem after installing the RUU_Vox_HTC_FRA_1.34.406.1_4.1.13.54_03.10.90_Ship ROM (and thus resetting everything in the profile), but I wonder if it's really the same thing.
My phone connects to the wifi, gets an IP (both the phone and the router show the same IP attributed), but PIE and Outlook Pocket can not use the network. It's just like they couldn't see the network. But they don't use Edge either to connect, so they probably somehow try to send data to the network,but they fail.
Oh, and WEP encryption changes nothing. And I can't test with fully removing the encryption, as I use an internet box, not a standard router.
What I don't get is that I was browsing just fine on this ROM and the same config in my router I wish someone with more knowledge would spare a minute to help us out here or at least point us in the right direction
Solved
I upgraded the firmware on my router... :d thx
I apologize if this has already been addressed. I looked, but couldn't find anything.
Here's my problem. I have a Tilt 8925 and WMWifi Router. My internet sharing connection settings are through Media Net. I have used this connection method for many months. Well, today, I connected my laptop through the WMWifirouter and everything was fine for about 5 minutes. Then my connection was lost, and upon trying to re-establish my connection, I notice that the internet sharing connection is trying to connect through AT&T ISP or something like that. I have repeatedly tried to switch it back to Media Net, but it keeps kicking back to the ISP setting. I have no way of connecting through ISP so, what happened and how do I fix it?
Thanks in advance!
Not sure if this is related or not. I never really paid attention to these settings before, so I can't say. If I look under the wi-fi connections settings tab on my phone, it brings up Configure Network Adapters. It is set to Virtual Ethernet Intermediate Miniport.......under that there are a whole bunch of other things. If I try to change it to IEEE 802.11b/g Compatible Wi-Fi Ad......, it appears as if it accepts the changes, bbut I then go immediately back into the settings and it is back on the virtual ethernet setting. Shouldn't I be able to change it, and could this possibly be why I can no longer connect using the WMWifiRouter?
Any help at all, please???!!!!
Even just a response of I'm not sure is better than no response at all.
Hi there,
I have never been able to understand the difference between My ISP and My Work Network. So, I just deleted MyISP. In My Work Network, I have the GPRS connection and it works perfectly fine. If I connect to activesync, I can use internet. Good.
The problem comes when I want to connect to VPN. I make a new VPN connction, I click on it and click/tap connect. it connects GPRS but the vpn doesnt seem to get connected. And every tap will just give the option of CONNECT which basically means that its not getting connected.
Quetsions:
1. What is wrong with my setup?
2. How can I verify that im connected with VPN or not?
p.s: the vpn is managed by a friend of mine, right now its on L2TP and if any changes are required in the settings. it can be changed.
Im using wm6.5 , hd mini.