I have the Problem that 3G is switching off after some minutes. Are ther any enrgie options i have to change?
When you say 3g is switching off - you mean the 3G symbol is changing back to G or E? If so, i guess your 3G signal is not strong and therefore the phone is switching bands. You can stop this by changing the auto setting under phone settings however this may cause you to loose network altogether.
no it is switching off, it is not changing
what is switching off - the data connection or the signal? What does your signal strength show?
the data connection, the signal stays
On a stock ROM with no changes, the data connection should stay on. Download advanced configuration tool from this forum - that will allow you to make changes required.
http://forum.xda-developers.com/showthread.php?t=420855
There are other software that allows you to change these settings - i dont know what you have installed and therefore can't tell you if one of these has the option.
i have this tool, but which settings should i change?
Related
For all the people that need their battery for a day or more I wanted to add the instructions on how to disable 3G.
Go into the dialer and type in *#*#197328640#*#*
Select "Debug Screen" on the menu
then hit "Phone Control"
then "UE State Control"
"Change RAT to GSM" will turn off 3G access and will leave your DATA on 2G.
This will save lots of battery especially for those who have low 3G signals.
Please note that rebooting the phone or even turning on "Airplane mode" will reverse these changes.
This means you will have to change the settings again (this is also the fastest way to cancel the changes and go back to 3G).
Thanks a ton for this. I'm sure it was in another thread, but I always saw mixed reports and hadn't tried it myself.
I have a 3-4 bar EDGE signal in my office, but only a 0-3 3G signal, so this will be a lifesaver.
However, as soon as there's a ROM that adds the force 2G option that should be there back into settings (and removes any other locks AT&T put in the software), I'll probably go that direction just because it is a pretty clunky way to do something that should be an option as is.
I have something to add to this. If you use a reboot or airplane mode to turn 3G back on, the next time you go to turn 3G off, you may need to re-enable 3G (WCDMA) before changing back to GSM. Apparently, the setting didn't get changed in the debug menu even though I got switched to 3G, so I had to put it back on 3G first.
Is this still the only way to disable 3G but leave 2G enabled on the Captivate? The apps in the Market are still all or nothing (3G or no data connection at all).
Thanks!
3G, 2G disabling?
Is there a way to disable the 3G/2G altogether but still use wireless?
You can always put it in airplane mode and then turn WiFi on if you don't want to use the AT&T network at all.
G'day all...
I have a TF101G and I have noticed that the mobile broadband seens to be consistently at the top of the battery usage list even when I have mobile data disabled and (get this) even when I have the SIM card removed.
My TF101G spends most of its life within WiFi range and I only need the 3G when it's out of the house.
Does anyone have any idea how to disable the mobile broadband transmission? Maybe I'm mistaken, but it seems dumb that it's still using battery to check in even when I tell it not to use the 3G.
Thanks,
Alex.
How have you disabled it?
I've seen many widgets/apps that say they're capable of disabling APN connections but the only thing they do is modify the APN connection name, so the 3G is still active but it never connects due to APN's changed name. The problem is that since 3G is not disabled at all, it might still use battery.
If you disabled from System > Wireless and Network > Mobile Network > Use packed data then 3G is turned off for sure. Also any system app that could manage that should be able to enable/disable that option.
Thanks for the reply.
I did actually try changing the APN as well as removing the SIM card. I still see continuous battery usage for Mobile standby at the top of my usage graphs in Aplications > Battery use.
I don't actually have the "Use packed data" option under System > Wireless and Network > Mobile Network - I only have Data enabled, Data roaming, Access Point Names, Use only 2G networks and Network operators.
I can always to to flight mode for no connectivity, but I can't for the life of me figure out how I can make the TF101G WiFi-only. Surely there must be some way of doing it. Maybe the forthcoming ICS update will fix it - we live in hope.
DarthWombat said:
I don't actually have the "Use packed data" option under System > Wireless and Network > Mobile Network - I only have Data enabled, Data roaming, Access Point Names, Use only 2G networks and Network operators.
Click to expand...
Click to collapse
Sorry, I was refering to "Data enabled". If "Data enabled" is toggled, 3g is enabled despite the APN name's. Maybe you could try to disable "Data enabled" and see if it doesn't consume more battery.
First thing I tried!
No joy there.
Problem solved.
See post by Notdawa in http://www.transformerforums.com/fo...p/16657-no-firmware-update-me.html#post149760
It's simply a matter of putting it in flight mode and then manually enabling WiFi. It works a treat!
I have now TW 9.2.2.4 FW and still if i do flightmode and then wifi on, i see cell standy as the biggest power consumer . to me it seems somehow the modem hardware is not properly switched off. anyone knows what modem chipset it is? or what could be the reason why this behavior?
If i do reboot with 3G modem off (so flightmode but with WiFi on), i get 'cell standby' as big power consumer after few hours. But reboot with 3G on (but no mobile data enabled) and also WiFi connected, then goingto flightmode + WiFi does not show 'cell standby' in battery chart . I had many problems and reboots with first ICS {9.2.2.3}, hopefully now i can get long and controlled battery life and no empty battery beeps in middle of night.
Hi!
This one is for simmodded users.
I ask for a way to set the threshold for toggling between uts and prs connections.
Often I experience the following: having uts with fair signal strength (3-4 bars) then, without leaving the same spot outside the q drops the 3g connection and starts a gprs connection (signal strength full).
If I force the uts connection I mostly get the weaker 3g connection reastablished. Problem with this settings: in areas where I won't have no 3g connection I have to manually switch back to auto setting.
So is there a way to modify the time of automatic connection switch, so I may have longer weak 3g connection before I drop to gprs?
The 4 answers!
Sent from my awesome XT897
I don't know such an app, only the manual way.
Theoretically you could use SmartActions to start an app change to 3G on good locations and change to 2G on bad locations.
However, I don't know such an app for this.
Maybe someone know a better solution.
Dear friends, some time when I have low 4g signal, I can not receiver calls.
I need some app for setting auto switch from 4G to GSM band, when the 4G is low.
Same problem, I have with wifi. I need some app for setting auto switch from wifi to Data mobile connection, when wifi signal is low.
Someone know any app that I can try for resolve this problems??
Thanks
The firmware has this feature itself.
i.e. it can switch to another network automatically if the current network signal becomes weak.
You should select the network mode as Auto Network Mode for it to function.
vndnguyen said:
The firmware has this feature itself.
i.e. it can switch to another network automatically if the current network signal becomes weak.
You should select the network mode as Auto Network Mode for it to function.
Click to expand...
Click to collapse
Yes, but when the signal is low, the phone don't switch network, because phone see the signal there is, low signal, but there is! But really, when signal is so low, I don't receive calls, my phone number is not available!
I need an app, for setting the minimal signal level, that the phone must change network
Hello XDA Community!
When my new phone (Huawei P9 Lite Mini) is on 3G/2G auto network mode, it consumes more battery than LTE/3G/2G auto mode even mobile data off.
I do not understand how this happens? For example, while 3G consumption at overnight is %10-15; LTE is only %2-3. This problem is the same in daytime too. Mobile data is off, unneccesary services/apps disabled, and no extra application installed while this happens. I tried all "wipe/factory reset/update firmware/factory reset/wipe/no app install" procedures, enabling all battery saving options, but it did not work. This is a problem for me when I'm in non-LTE areas.
This problem occurs the same result in different locations. There was no problem with my previous phone and I use same nano sim card.
I tried the following but it did not work:
- Wipe cache, factory reset, wipe cache,
- Wipe data/factory reset over recovery menu,
- Update latest firmware, wipe data etc. again.
How this happens and where am I doing wrong? Thank you for your help, best regards!
EDIT: PROBLEM SOLVED!
I changed my mobile carrier (provider) and the problem is gone. This is very interesting! I worked for hours and days to solve the problem, but this problem is neither caused by the phone nor by the software...
WCDMA (aka 3G with support for 2G/Edge) is in always-on mode on most phones, because that's how you receive and emit phone calls and, for most phones, SMS (in some more recent phones, LTE takes care of sending and receiving SMS/MMS), so if you're in an area where 3G/2G reception is poor, your phone has trouble locking on a cell with enough power to maintain contact, hence the battery drain.
4G/LTE only works for data, and voice if you have VoLTE (Voice over LTE) enabled, but works on a on-demand mode, even with cellular data constantly enabled. In other words, the 4G modem on your phone will memorize the latest position and IP address the nearest 4G tower/cell allocated it, and connect to it using the memorized settings when you need it to.
Not so with 3G, where DHCP doesn't exist, at least not the way it does in 4G: it uses PPP (Point-to-Point Protocol), where an ad-hoc IP address is attributed to each new connection, based on a pool of existing addresses allocated to the tower and its owner (carrier) by the authorities.
UglyStuff said:
WCDMA (aka 3G with support for 2G/Edge) is in always-on mode on most phones, because that's how you receive and emit phone calls and, for most phones, SMS (in some more recent phones, LTE takes care of sending and receiving SMS/MMS), so if you're in an area where 3G/2G reception is poor, your phone has trouble locking on a cell with enough power to maintain contact, hence the battery drain.
4G/LTE only works for data, and voice if you have VoLTE (Voice over LTE) enabled, but works on a on-demand mode, even with cellular data constantly enabled. In other words, the 4G modem on your phone will memorize the latest position and IP address the nearest 4G tower/cell allocated it, and connect to it using the memorized settings when you need it to.
Not so with 3G, where DHCP doesn't exist, at least not the way it does in 4G: it uses PPP (Point-to-Point Protocol), where an ad-hoc IP address is attributed to each new connection, based on a pool of existing addresses allocated to the tower and its owner (carrier) by the authorities.
Click to expand...
Click to collapse
Thank you for your reply!
When I googled about 3G vs. LTE battery consumption, everyone says that LTE will consume more batteries. That's make sense on first thought. So what I've been through is very interesting to me.
I think about is there a problem with my phone's 3G antenna. (footnote: I don't know about that 3g and LTE antennas are same or seperate?)
But I understand that you say this is normal, right?
Edit: I found a forum that this problem may be due to the operator (carrier). I'm still investigating...
3G and 4G operate on basically the same principle: receiving and sending "information" via radio waves.
The difference lies in the frequencies each standard uses, the way the data sent over them is modulated and demodulated, and how handsets make and maintain connection, so if you stay in the same location, and set your phone to 3G-only, then switch Airplane mode on then off, it'll take your phone longer to reconnect to the 3G cell/tower with the strongest signal (not necessarily the closest to you), because it'll have to go through the whole getting-acquainted process again, whereas in 4G, it'll go straight to the "Hey, how do you do? Long time, no see".
Now, if your phone antenna has a problem, you could be standing a few feet from the tower, in line of sight, and still get a crappy to non-existent signal. How many bars are showing on your screen is just an indication of how well your phone is receiving the signal from the tower; it doesn't mean that this signal is consistent and steady, hence the bars coming and going in real time.
If I were you, I'd download and install the Hidden Settings app from the Play Store, and run it; there, you go to RadioInfo, and you'll get a lot of information about how your phone modem actually works. It's a bit technical, but it would give you an indication.
I will try and looking for a new carrier. Thank you again. See you.
I changed my mobile carrier (provider) and the problem is gone. This is very interesting! I worked for hours and days to solve the problem, but this problem is neither caused by the phone nor by the software...