Database Info

Hard SPL Problems

I have problems to use the Hard-Spl v1. I have a new HTC-Kaiser from T-Mobile. I start the Application HARD-SPL (I want to upgrating with Dutty´s ROM)
I run the kaiser-hardSPL.exe on Computer (PC)
I follow instructions on screen!!!!!
on the mobile i the question to start the applikation i answer Yes and then i get a with screen on the HTC Kaiser. NO tri-color-screen !!!
Please help, thx
Thomas

Thomas_Germany_Hamburg said:
I have problems to use the Hard-Spl v1. I have a new HTC-Kaiser from T-Mobile. I start the Application HARD-SPL (I want to upgrating with Dutty´s ROM)
I run the kaiser-hardSPL.exe on Computer (PC)
I follow instructions on screen!!!!!
on the mobile i the question to start the applikation i answer Yes and then i get a with screen on the HTC Kaiser. NO tri-color-screen !!!
Please help, thx
Thomas
Click to expand...
Click to collapse
From what I've read you need to remove your sim card and your microsd card then try again

There is no simcard and microsd in the htc Kaiser.
on the HTC Kaiser is the original T-Mobile software, nothing else

Perhaps your problem is related to new SPL... take a look at http://forum.xda-developers.com/showthread.php?t=349476
Cheers.

When your phone is booting up, look in the lower right corner. If you have a line that reads:
D 1.57.00.00
Then you most likely have the issue in the thread mentioned by jcespi2005. If you have:
D 1.56.00.00
Then its probably something else (as 1.56.00.00 should be able to do the HardSPL).

Why not flash the old SPL to the device then you can use Hard_SPL. I havent checked but arent there original ROM available(of course CID/carrier specific) from before 1.57.

wpbear said:
Why not flash the old SPL to the device then you can use Hard_SPL. I havent checked but arent there original ROM available(of course CID/carrier specific) from before 1.57.
Click to expand...
Click to collapse
The real problem is SSPL used to flash HardSPL is not working with this one, so you can't go back to previous SPL... don't know what shipped ROMs are out that allows flash over this SPL...but perhaps this can be a way to go...
Cheers.

The Rom of my Phone is d.1.56.00.00 !
I do a hardreset, but Hard SPL dont work!

well... for the Tilt you can't flash the "official" ROM back to the device because of an "Invalid Vendor ID", I'm not sure why this is but it just doesn't work. You can however flash the AKU0.4.4 ROM to an unmodified Tilt so the CID apparently is good on that ROM. However I've done this and it does not fix the "white screen" issue on the affected devices.

sirsycho said:
well... for the Tilt you can't flash the "official" ROM back to the device because of an "Invalid Vendor ID", I'm not sure why this is but it just doesn't work. You can however flash the AKU0.4.4 ROM to an unmodified Tilt so the CID apparently is good on that ROM. However I've done this and it does not fix the "white screen" issue on the affected devices.
Click to expand...
Click to collapse
oh well it was an idea. Another reason for me to put off the Tilt purchase.

wpbear said:
oh well it was an idea. Another reason for me to put off the Tilt purchase.
Click to expand...
Click to collapse
I might be returning mine because of this. Bummer.

Need Help! Asap!!!!!!!!!

i was attempting to debrand my v1615 (UK) and after i hardSPL'd it and attempted get the HTC factory rom on i got an error saying Vendor ID error. so i need advise on geting around this or the original v1615 ROM. failing that my fone may take a swim tomorrow and ill have to inform the insurance

Are you sure you installed HardSPL properly?

yea well 99% sure it went thru ok. phone is stuck on the tri colour screen and cant do anything from there. wont even activsync so i cant try to run SPL again

bump******

kantosbrin said:
yea well 99% sure it went thru ok. phone is stuck on the tri colour screen and cant do anything from there. wont even activsync so i cant try to run SPL again
Click to expand...
Click to collapse
what does the tri-color screen say... give me all the text on it.

ok in the top right is says RUUNBH
and under that but on the left it says
KAIS130
spl-1.56.0000
cpld-8
then either USB or serial depending on if the cable is in or not.
hope u can help

See my post here.

jockyw2001 said:
See my post here.
Click to expand...
Click to collapse
In addition to what jockyw2001 said...
You do not have HardSPL installed. Please try again and follow the instructions to verify (after you can boot back into the OS).

ok i out my depth here lol! i no im being a pain but is there any way of solving this simply? because that thread i was just send to made no sense

sounds like you have a lot of reading to do... or maybe you have a friend who is well versed in these types of things...
Really quickly... you need to find and download mtty.exe (check the wiki) and then you should learn how to connect it to your device and follow the instructions from jockyw2001.

Which Flash program for WM6 & Dutty's WM6.1 Hybrid v2 ROM

Hey everyone,
I'm having a heck of a time getting this flash to work properly. Every time I try, I get stuck at the flash status screen...Sorry if this is a re-post, i don't know all the tech terms, so honestly, i don't know what some of the other posts pertain to.
Anyways, i follow the directions, but when it goes from the tri-color screen where it displays "USB" at the bottom, it gets a connection error before the progress ever gets past 0%...
Has anybody else had this issue?
My tilt is currently bone stock, i just reset it before i did tried this to ensure nothing else i had on it would be an issue.
I tried using both the KaiserRUU and the CustomKaiserRUU without luck.. Is there a different one I should use?
Any help is GREATLY appreciated. You guys do some amazing stuff on this site, and i am just starting to learn.
Thanks,
-Tater

first, have you flashed HardSPL?
also, I recommend this guide:
http://mbarvian.freehostia.com/2008/09/10/flashing-your-first-rom/

i tried flashing the hardspl, but had similar results...after starting the program on my PC, the screen on my Tilt goes solid white.....the PC screen says im supposed to wait for the tri-color screen, but it never goes past white screen....
i will also check out the link you posted..
thanks,
Tater

Darth Tater said:
i tried flashing the hardspl, but had similar results...after starting the program on my PC, the screen on my Tilt goes solid white.....the PC screen says im supposed to wait for the tri-color screen, but it never goes past white screen....
i will also check out the link you posted..
thanks,
Tater
Click to expand...
Click to collapse
yes, the link I gave you should definitely fix the problem
oh, and DONT TRY FLASHING A ROM WITHOUT HARDSPL!!!
can't stress that one enough

ok, last time i will bug ya( for a few anyways )
it says in the manual, that there is usually a recommended HardSPL...
i dont see where Dutty recommends a specific HardSPL?
any suggestions?
thanks again...

Darth Tater said:
ok, last time i will bug ya( for a few anyways )
it says in the manual, that there is usually a recommended HardSPL...
i dont see where Dutty recommends a specific HardSPL?
any suggestions?
thanks again...
Click to expand...
Click to collapse
lol don't worry bout bugging me
try hardspl 3.29

Darth Tater said:
ok, last time i will bug ya( for a few anyways )
it says in the manual, that there is usually a recommended HardSPL...
i dont see where Dutty recommends a specific HardSPL?
any suggestions?
thanks again...
Click to expand...
Click to collapse
Any of jockyw2001's or cmonex's 3.* Hard Spl. 3.29 is a good one.
Dave

dang!,
same issue....i get the the part where it shows progress bar and i get a communication error. Should i try the force USB version? I read that it is for those of us with communication issues....

Darth Tater said:
dang!,
same issue....i get the the part where it shows progress bar and i get a communication error. Should i try the force USB version? I read that it is for those of us with communication issues....
Click to expand...
Click to collapse
yes, try that and post the outcome

READ!!!
Use either jumpSPLV1 or 1.56 afterwards hardSPL 3.29 or 3.56 (whatever the chef suggests - I user 3.56 with no probs).

Ok, so when i try to run JumpSPL from the tilt, I make sure that 0x00000000 is the value and i point it to the apropriate .nb file, and the screen goes white....it never makes it to the tri-color screen....
I followed the instructions exactly...
I tried using the Force USB version from my PC and it has the same communication error....
perhaps i need to use a different JumpSPL?
if it helps, this is what is on my Dev info:
ROM version 1.57.502.2
ROM date 08.25.07
Radio version 1.27.12.11
Protocol version 22.45.88.07H

Try JumpSPL1.56-KAIS.exe. I flashed 4 Kaisers, 2 worked with jumpSPLV1 and 2 with the file above but last but not least ALL could be flashed.
TAKE OUT SIM AND SD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

LOL, like the name and avatar.

Darth Tater said:
Ok, so when i try to run JumpSPL from the tilt, I make sure that 0x00000000 is the value and i point it to the apropriate .nb file, and the screen goes white....it never makes it to the tri-color screen....
I followed the instructions exactly...
I tried using the Force USB version from my PC and it has the same communication error....
perhaps i need to use a different JumpSPL?
if it helps, this is what is on my Dev info:
ROM version 1.57.502.2
ROM date 08.25.07
Radio version 1.27.12.11
Protocol version 22.45.88.07H
Click to expand...
Click to collapse
Switch USB ports. My HP laptop has 4 USB ports (2 left, 2 right), and the left ports cause a 220 Communication Error, but the right ones work fine.

NotATreoFan said:
Switch USB ports. My HP laptop has 4 USB ports (2 left, 2 right), and the left ports cause a 220 Communication Error, but the right ones work fine.
Click to expand...
Click to collapse
same here on a toshiba a215-s7422

OK, so I got it to work!!! Thanks very much guys.
I I think it may have been a combination of using one of the USB ports on the motherboard (instead of front ports) and using that JumpSPL1.56-KAIS.exe version instead of the other one I was trying.
This is a great looking rom. Now, i just have to get used to using it....
Thanks again to everybody who contributed to helping me get this phone flashed.

HTC Snap 511 (Willow): SSPL, HardSPL and original SPL by JockyW

Attached you find all you need to flash cooked ROMs on your HTC Snap 511 (Willow).
The sspl/hardspl are confirmed to work fine on the HTC Willow platform (HTC Snap 511).
It will not work on the HTC Maple platform (Dash3G). Running this sspl on a Dash3G will definitely brick it. Also the HTC CEDAR platform (Ozone) is not supported. For the Dash3G and Ozone I have already developed a sspl/hardspl.
The packages contains a SSPL, HardSPL, patched ROM updater and the original Snap S511 SPL. The package is based on SPL v0.34
Instructions:
1. remove SD and SIM cards (don't forget otherwise the sspl is likely not to work!!)
2. connect your device to your pc with a USB cable and wait until it is synced
3. extract the file "Snap S511 HardSPL by JockyW.zip" and execute "auto.bat"
4. follow all instructions given on screen: first the sspl is copied to the device and executed. You must confirm running JumpSPL on the device: first time you must click Yes to allow it to run, you also must click the trackball to continue execution of JumpSPL. The device display will turn dark and after that the romupdate tool will install the hardspl on your device. (the identification string in the tri-color bootloader screen is "0.34.Hard")
5. to test the sspl and the hardspl you can flash a splash screen
Once the HardSPL is installed on your device you can flash any cooked or original ROM.
A donation for my work would be highly appreciated
Have fun,
JockyW
PS: Moderators please make this a sticky. Thanks.

Donation
Donation has been sent. Thank you for this.

Good work!!!!

Thanks Jocky, sending you good vibes and tips!
Once we install the hardSLP on the sprint snap, which cooked roms can we use? Are we going to need one specially cooked for the snap 511?

dougmwpsu said:
Thanks Jocky, sending you good vibes and tips!
Once we install the hardSLP on the sprint snap, which cooked roms can we use? Are we going to need one specially cooked for the snap 511?
Click to expand...
Click to collapse
Yes, ookba is waiting to get his own phone to get a ROM working... Donations really speed up that process
Should this be stickied like the last few? Maybe consolidate all into one?

Black_V!per said:
Yes, ookba is waiting to get his own phone to get a ROM working... Donations really speed up that process
Should this be stickied like the last few? Maybe consolidate all into one?
Click to expand...
Click to collapse
Anyone care to donate their S511 to me for a week or so?

ookba said:
Anyone care to donate their S511 to me for a week or so?
Click to expand...
Click to collapse
Maybe the next week I'm on vacation... can the phone be service deactivated while you have it?

dougmwpsu said:
Maybe the next week I'm on vacation... can the phone be service deactivated while you have it?
Click to expand...
Click to collapse
Sure it can. Where are you though?

ookba said:
Sure it can. Where are you though?
Click to expand...
Click to collapse
Raleigh, NC. My next vacation isn't till the week of Christmas though, so maybe someone else can step up in the meantime. I'll also be out of the office again for a week in the spring.

first off, thanks so much to Jocky and Ookba for all the work you guys do! but i'm having some issues. i've dont a lot of searching on here and i can't find a solution hopefully someone can help me. i can't get the hardspl to run successfully.
my bootloader screen shows this:
CEDA200
SPL-0.34.0000
MicroP-Willow#C (LED) v58B
i'm using windows 7 (through VMWare on my iMac), everything seems fine until the pop up on the phone, i click the button (the not really a trackball button) and the screen goes black, i lose all connectivity through WMDC and the Rom Utility gets error 266.
If i don't click when the pop up shows on the phone, the Rom Utility will show and then the phone will go into the bootloader with USB written in the white area then i get the error 266 again.
of course there's no sim because it's a Sprint s511, and the sd card is always removed.
what can i do? i'd really love to get 6.5 on there, but i'm at a loss.

The fact that your running on a MAC with VMWare makes me think the issue could be in the connection...
Im not even sure if Win7 works, i could be wrong however. You wouldnt happen to know of anyone that has a WinXP machine would you?

I did try in vmware with XP and Activesync, but it did the same things. I have a Dell that I was gonna make a hackintosh, but I'm gonna throw xp on it and try using that machine. I was thinking it was the vmware too, i guess i just wanted one of you guys (you know, the one's with a clue! LOL) to confirm.

I applied the HardSPL to my snap using Windows 7 and everything went well

robconway said:
I did try in vmware with XP and Activesync, but it did the same things. I have a Dell that I was gonna make a hackintosh, but I'm gonna throw xp on it and try using that machine. I was thinking it was the vmware too, i guess i just wanted one of you guys (you know, the one's with a clue! LOL) to confirm.
Click to expand...
Click to collapse
Thats what it sounds like... Good to know it works on Win7 though SPIK3.

Thanks Black_V!per for responding and all. I did finally get it going! I set up the dell with XP and it actually didn't work at first. I had originally unRARed the package on the iMac and just copied the unarchived folder over to the XP machine, thinking it would save me a download, but it didn't work. So i just dl'd an RAR utility for windows and unpacked the RAR on the xp machine and it worked perfect. originally the Rom Updater said it couldn't find the nbh file. all's well! And i'm loving 6.5!!
Thanks again Jocky and Ookba!!!

robconway said:
Thanks Black_V!per for responding and all. I did finally get it going! I set up the dell with XP and it actually didn't work at first. I had originally unRARed the package on the iMac and just copied the unarchived folder over to the XP machine, thinking it would save me a download, but it didn't work. So i just dl'd an RAR utility for windows and unpacked the RAR on the xp machine and it worked perfect. originally the Rom Updater said it couldn't find the nbh file. all's well! And i'm loving 6.5!!
Thanks again Jocky and Ookba!!!
Click to expand...
Click to collapse
Must have corrupted during the download... Havent seen that since my 56k-days.
Glad to hear that!

First off, I appreciate everyone's hard work throughout this whole process.
Unfortunately I am running into a problem. The auto.bat is able to copy the JumpSPL file and the .nb file to my phone just fine. However once the Rom Update Utility starts the flashing process, the phone shuts off.
I did a hard reset to my phone, and went through the process again. The JumpSPL notice popped up on the screen, but then crashed when I hit OK. I know it crashed because the Windows Error Reporting popped up (which apparently I had disabled before I did the hard reset, so I never was able to tell if it was still running).
So then I manually ran the JumpSPL file. This time the memory box popped up, so I hit OK with the Jump Address at the default 0x00000000. It then asked which SPL file I wanted to use. I chose the .nb that was copied over. Then the Windows Error Reporting screen showed up again.
I'm not sure what is going on, but hopefully the details I just provided will allow someone to figure something out. Thanks.
BTW: My phone is a Sprint HTC Snap S511, and my splash screen is the same as the one posted before:
CEDA200
SPL-0.34.0000
MicroP-Willow#C (LED) v58B

Jaymoon said:
First off, I appreciate everyone's hard work throughout this whole process.
Unfortunately I am running into a problem. The auto.bat is able to copy the JumpSPL file and the .nb file to my phone just fine. However once the Rom Update Utility starts the flashing process, the phone shuts off.
I did a hard reset to my phone, and went through the process again. The JumpSPL notice popped up on the screen, but then crashed when I hit OK. I know it crashed because the Windows Error Reporting popped up (which apparently I had disabled before I did the hard reset, so I never was able to tell if it was still running).
So then I manually ran the JumpSPL file. This time the memory box popped up, so I hit OK with the Jump Address at the default 0x00000000. It then asked which SPL file I wanted to use. I chose the .nb that was copied over. Then the Windows Error Reporting screen showed up again.
I'm not sure what is going on, but hopefully the details I just provided will allow someone to figure something out. Thanks.
BTW: My phone is a Sprint HTC Snap S511, and my splash screen is the same as the one posted before:
CEDA200
SPL-0.34.0000
MicroP-Willow#C (LED) v58B
Click to expand...
Click to collapse
Is your phone applications unlocked? When I did mine it gave me a bunch of errors because it wasn't applications unlocked. Also make sure you remove your memory stick.

SPIK3 said:
Is your phone applications unlocked? When I did mine it gave me a bunch of errors because it wasn't applications unlocked. Also make sure you remove your memory stick.
Click to expand...
Click to collapse
How would I go about checking this?
I remember on my Samsung Ace, before the 6.1 update, I had to install an "application unlocker" that allowed unsigned programs to install. Is this the same thing with the Snap? Also this is the Sprint version, so I don't have a Sim card, or anyway to typically "unlock" this phone.
EDIT: Ah, now I know what you mean. I found the SDA Application Unlock here: http://forum.xda-developers.com/showthread.php?t=563761
The Rom Update Utility finished successfully! Now to move on to the next step... Thank you SPIK3

No problem, glad I can help.

Noob help w/ATT Fuze + WM6.5

Trying to flash my AT&T Fuze with HardSPL so I can pop a ROM of WM6.5 on it. Not having any luck.
I run the HardSPL executable, it sees the phone (with the current 5.11.XX... ROM version), and then when I hit OK, and see the progress bar (at 0%), it just sits there for about 45 seconds, then gives me a communications error.
Tried this on WinXP and Win7 with the same results. What am I doing wrong?

crescent.wire said:
Trying to flash my AT&T Fuze with HardSPL so I can pop a ROM of WM6.5 on it. Not having any luck.
I run the HardSPL executable, it sees the phone (with the current 5.11.XX... ROM version), and then when I hit OK, and see the progress bar (at 0%), it just sits there for about 45 seconds, then gives me a communications error.
Tried this on WinXP and Win7 with the same results. What am I doing wrong?
Click to expand...
Click to collapse
Is the phone new. We have reports that the SPL Loader changed and prevents flashing HardSPL. Check ur SPL it should not read anything different from 1.90. If it is a higher number then.
Go to the Hardspl thread and flash the 1.90 stock spl frome there first.

Yes, the phone is brand new.
SPL-5.10.0000 is displayed when I enter the bootloader. Would you mind pointing me in the right direction with the HardSPL thread (where I can flash to 1.90)? Can't seem to find it.

crescent.wire said:
SPL-5.10.0000 is displayed when I enter the bootloader. Would you mind pointing me in the right direction with the HardSPL thread (where I can flash to 1.90)? Can't seem to find it.
Click to expand...
Click to collapse
The 1.90 u can find in the HardSPL thread. But check if its ok to get from 5.1 to 1.90
I was more thinking from 1.9XXX to 1.90, so still within the 1.9 loaders. Dunno if its ok for the 5.1 to go down. It should but not shure about that.

Great. I'll check it out. Worse comes to worst, I just may not be able to throw WM6.5 on this, correct?

crescent.wire said:
Great. I'll check it out. Worse comes to worst, I just may not be able to throw WM6.5 on this, correct?
Click to expand...
Click to collapse
well when hardspl works, everything is possible. All the GSM roms are also for fuze afak

http://forum.xda-developers.com/showpost.php?p=4209384&postcount=589
Look through the HardSPL thread, seems that 5.1 Fuze is working with the 1.9 SPL.

Okay, so I was able to boot into the bootloader, where it tells my SPL is 5.1. I can get the HardSPL exe to run and get all the way to the Progress Bar screen (and the phone also jumps to a grey screen with a progress bar), but they both sit at 0% for about 1 min, then it cancels and says "ERROR(262): Update Failed."
Any ideas?

I also had this issue. I did the CID unlock first, then HSPL. I was then able to complete the upgrade.

No joke. I'll have to try that, then.
And, in anyone's opinion, what's the best cooked ROM to be using? EnergyROM?

crescent.wire said:
Okay, so I was able to boot into the bootloader, where it tells my SPL is 5.1. I can get the HardSPL exe to run and get all the way to the Progress Bar screen (and the phone also jumps to a grey screen with a progress bar), but they both sit at 0% for about 1 min, then it cancels and says "ERROR(262): Update Failed."
Any ideas?
Click to expand...
Click to collapse
Are you doing this through activesync. I asume you are. Make sure the file is placed on your main drive of the computer and ran from there. It cannot be in folders hidden. Otherwise it won't work. I had this issue with prior devices while upgrading.

crescent.wire said:
No joke. I'll have to try that, then.
And, in anyone's opinion, what's the best cooked ROM to be using? EnergyROM?
Click to expand...
Click to collapse
That is kind of like asking which is the best baseball team, NASCAR driver, flavor of potato chip or type of candy. Some cooks go for stability. Other cooks go for the latest release. Some cooks throw in all kinds of goodies. Other cooks put an the absolute minimum in the ROM, so the users can add just what he wants. You may hate my favorite ROM and I may hate your favorite ROM. That is why there are so many ROMs to choose from and all these wonderful cooks making them. Try a several different ROMs and see which you prefer.

Mxdadevolper said:
I also had this issue. I did the CID unlock first, then HSPL. I was then able to complete the upgrade.
Click to expand...
Click to collapse
And how might one go about unlocking the CID first?

yamilrx said:
Are you doing this through activesync. I asume you are. Make sure the file is placed on your main drive of the computer and ran from there. It cannot be in folders hidden. Otherwise it won't work. I had this issue with prior devices while upgrading.
Click to expand...
Click to collapse
Yep, doing all that. Thanks, though.

dlweston said:
That is kind of like asking which is the best baseball team, NASCAR driver, flavor of potato chip or type of candy. Some cooks go for stability. Other cooks go for the latest release. Some cooks throw in all kinds of goodies. Other cooks put an the absolute minimum in the ROM, so the users can add just what he wants. You may hate my favorite ROM and I may hate your favorite ROM. That is why there are so many ROMs to choose from and all these wonderful cooks making them. Try a several different ROMs and see which you prefer.
Click to expand...
Click to collapse
A fine point, to be sure.

Sorry, all -- kind of got ahead of myself with all these replies.
So, can anyone point me in the right direction for unlocking my phone's CID?

Simple question
crescent.wire said:
Yep, doing all that. Thanks, though.
Click to expand...
Click to collapse
I have one question. Do you have the phone in "ActiveSynch" mode before running the HardSPL? I found that running it while in the "BootLoader" does not work well, when running the HardSPL.
So, activesynch --> run the hardspl --> make sure you click "Ok", when the phone prompts you, if it is okay to run the 2 executables on your phone --> then watch your phone restart into the "bootloader", then update the hardspl...
Just observation from my past experience...

cso5874 said:
I have one question. Do you have the phone in "ActiveSynch" mode before running the HardSPL? I found that running it while in the "BootLoader" does not work well, when running the HardSPL.
So, activesynch --> run the hardspl --> make sure you click "Ok", when the phone prompts you, if it is okay to run the 2 executables on your phone --> then watch your phone restart into the "bootloader", then update the hardspl...
Just observation from my past experience...
Click to expand...
Click to collapse
Hmmm... I do not have it in ActiveSync mode. I actually have an Exchange connection set up on the phone right now with work. So I should remove that connection, set it to sync ONLY with my desktop, then run HardSPL with ActiveSync 4.5 (on XP) // WMDC (on Vista/7) open?
That's good advice, if I understand you correctly. Thank you!

Did u try to go Stock 1.90 first before doing HardSPL or did u try to flash direct to the unsigned 1.9 ?
As far as I know u have to switch from 5.1 first to the 1.90 signed and then to the unsigned version. See the hardspl thread for more info. Go to this
STEP BY STEP HOW TO RETURN TO STOCK SPL
first.

schnitzelbrain said:
Did u try to go Stock 1.90 first before doing HardSPL or did u try to flash direct to the unsigned 1.9 ?
As far as I know u have to switch from 5.1 first to the 1.90 signed and then to the unsigned version. See the hardspl thread for more info. Go to this
STEP BY STEP HOW TO RETURN TO STOCK SPL
first.
Click to expand...
Click to collapse
Awesome. I'll give that a shot, too. Thanks, guys!