Related
Hello XDA Nice Team !
By mistaken i wrote some file to my bootloader in my I-Mate Jam ..
That was after using the bad ROM : 2.03
it's the worst cooked version i saw !
Now my bootloader mode is working .. but no way to connect to PC with USB port ..
My computer does not recognize my Magican when plugged in bootloader mode anymore!
Bootloader Ver: 1.0
is there any way to fix or upgrade or restore original bootloader
Now i cant upgrade or downgrade my magican by any method
Noway to use successful connection with any roomupdate utility
Please help me to fix or restore my bootloader!
Thanks to any one read or replay or try to help or help me to resolve my problem
XDA lover
i'm sorry that happened mate...
i've had success with flash-from-bootloader attempts before, both on my Magician, when i accidentally flashed off of Vista and it'd enter the bootloader every week or on a reset using the reset hole, and also on my Wizard when i ignored warnings from WM5torage and it'd only enter the bootloader
what precisely happens when you connect to the PC, allow USB connections in AS/MDC, and let the phone enter bootloader however it does? i can just flash a rom from there, but i won't (iirc) get any reports of as recognising the device...
My experience:
1- when i plug my sd card into my jam .. usb not recognized in bootloader mood !!
2- when i use puty or roomupdate it reaches to USB> then when i type any command it does not respond !
3- i could do something .. i let my phone bootup and this i-mate logon screen stays 4ever .. i connected my ppc to pc and i could explre my imate by activesync ...
i could reach something .. when i explore my phone and remove everything from startup folder .. my phone boots .. and i can see start botton .. no touch alignment comes .. and everything works .. but.. screen is virtually reversed .. i can see the OK botton but i must click on the facing area and it be clicked ..
i think i executed some wrong hard SPL to my phone ant that happened >
is there any way to resolve this problem?
is there any way to erase flash on my I-Mate Jam????
is there any way flash my phone?
i also have prepaid JAFWM with pkey and USB cable .. no BOX ..
Help please!
that's messed up... howsabout flashing it at the point when the phone boots up? if there's an AS connection there, then it may work... i'd flash to an official rom though
Same problem , PLS Help !!!
Thx for help
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
If your magician isn't detected at ALL by your PC when plugging the USB cable into it (i mean, no new hardware; no unrecognized hardware; nothing is detected in your PC when you plug the USB cable), and unless you had previously made a SD backup of your entire Flash with this procedure ( http://wiki.xda-developers.com/index.php?pagename=MagicianSDflash ), then your only option will be to build a JTAG diag cable:
Here are some general directions / ideias:
Magician JTAG pinout: http://wiki.xda-developers.com/index.php?pagename=MagicianJTAG
How to build/run the JTAG: http://wiki.xda-developers.com/index.php?pagename=DeadBoot
Photos : http://www.cf-box.com/htm_data/55/0912/1679.html
Some interesting stuff for debugging problems: http://pda2u.ru/ptopic205.html
For sure cotulla has one built so to test his ROMs + bootloader - maybe he will be willing to give you some directions if you run into problems, and above all, give you a prepared .nb0 (with the bootloader file) for your magician, which i do not know if there's one out there, extracted from an original ROM.
Anyway, you can always try and do it for yourself using itsme utilities. Follow this link: http://forum.xda-developers.com/showthread.php?t=218643
Regards
Keeper,you're awesome! I'm searching for JTAG,too
xiaojin1985 said:
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
Click to expand...
Click to collapse
Dear xiaojin1985 ,
Thx for your help, But unfortunately i tried your solution but it dosnt work !
Dear Keeper,
Thanks too for your help,
and i think the solution for my problem is one of the solutions you says ( How to build/run the JTAG: ) ,
but the pictures is not available anymore , so pls can you get the pictures ?
All the pictures are in here:
http://s218.photobucket.com/albums/cc23/alex_beda/ and in attachment there's a .mth file with all the pics built-in.
Don't take it wrong what i'm about to say, but in all honesty if you can't figure this out yourself (digging up the internet for the missing pics), i would suggest that you shouldn't try this, since this ain't easy at ALL...
Just to give you some ideias, it will require you to adapt your magician test point signals (TDO;TDI; nRESET; etc,)seen on the magician pinout pic to what is said; solder very thin wires (best done with a small hot air tip); fixate the small dip switch (micro switch) to be always on; keep the USB connected...idk... plus alot of other small details which ain't easy to accomplish.
Personally i haven't tried this yet but for sure it would work
If you decide to go ahead, please post some results!
Connection error solution
this is my problem
hi all. A friend of mine gave me an S100, and after i played for a few days with it, i decided to update it's rom. A "country error" problem appeared,cause i have the greek version, so i ran MaUpgradeUt_noID.exe which completed (as showed 100% process). My (new) problem is that i cannot update anymore. Every time i enter boot menu, i ran the upgrade
(HTCMAG_ROM_WWE_O2.rar) following all the steps normally. When the device resets (so the upgrade is going to start), it's re-reseting again and showing ERROR 101 connection error. Any ideas?
Qtek Greek version
R 1.12.00
G 1337.42
D 1.12.00 WWE
P.S. apart the problem everything is function properly
and the solution
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe radio_1.11_greek but idont reset the qtek in first screen
and upgrate downgrate start all ok
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe MagicianRadio_1.12.10. uk but idont reset the qteki n first screen
upgrate from radio 1.11 to 1.12.10
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run HTCMAG_ROM_WWE_O5_251209
everything is ok my magisian run the new Rom
here..........................
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
I have similar problem, can't connect to PC anymore, but flashing with SD card works for me
have you tried different ROM images?
TQY said:
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
Click to expand...
Click to collapse
It sounds like you did not carefully read this.
That is also where this should have been posted. A new thread should not be started for this type of issue. I understand you are panicing. However, in almost all situations the phone can be recovered.
That said, Hold volume down and hit the reset button. It will put you in the tricolor screen. In the white it says serial. Connect it to your usb cord. It should now say usb. Now flash the STOCK rom.
be sure that battery over 50% then follow arupphental's
I have a friend with a kaiser and the same problem. can this be applied to it? i dont want to search through the forum forever...
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
X2D said:
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
Click to expand...
Click to collapse
ok i thought someone would say that. was just wondering off hand. thanks x2d
A.creature said:
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
Click to expand...
Click to collapse
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
I had the same problem after a faulty ROM from Vodafone NL, what I had to do is before I wanted to flash my ROM do a hard reset on my device (please back-up your personal data before doing this). After the hard reset, I could get a stable connection with activesync and flash my ROM
While the circumstances are different, my advice is still the same: http://forum.xda-developers.com/showthread.php?t=481527
longnguyen30 said:
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
Click to expand...
Click to collapse
Stumbled upon this.. and yes the advise is good, when you run the flashing utility (i.e. CustomRUU.exe), it says you need an Active Sync connection, but you really dont, you can flash it anyway, it seems to find the device via USB regardless.
ufff!!!! to me yes found right, thank you thank you to first post. (flashing from SD)
Undetected
Well i had the problem where my phone wasnt getting detected at all.... i put the stock rom and radio but couldnt put stock spl on the phone with sdcard.... after trying different computers/usb wires/settings i returned it for a new one and this one works fine.
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
I think you have been bricked your device...
dineshkumaar said:
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
if it's not recognized, remove the SIM card, the SD card, and on the PC open activesync and disable usb connections. for more info open this link
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
what if the device is bricked
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
dineshkumaar said:
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
Click to expand...
Click to collapse
you have to find another rom and try to flash it to your PDA.
ARE YOU RUNNING windows XP on your PC?
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
dineshkumaar said:
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
Click to expand...
Click to collapse
have you tried to upgrade another ROM, and if you did, is your PDA now working?
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
dineshkumaar said:
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
Click to expand...
Click to collapse
Have you read here?
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Try to reflash with another ROM
Hope it helped
And don´t forget to vote!
I had already done those steps to get no results.
its my badluck.
If you cannot get into bootloader and you have done the steps above, then you cannot flash to another rom.......it would seem you now have a paperweight im afraid
I am still not able to revive my device. I know that it is just due to corrupt bootloader but don't know how to repair it.
If anybody ever has solution for this... kindly let me know.
Regards
Have you tested mtty?
I would recommend to PM a chef on Universal forum
Good luck,
Mtty is not detecting my device
it says can't open usb port
One More thing I have noted is that when I keep the device connected with the pc, at a certain interval of about 10-15 mintues my device's Led shows RED Light for few seconds and then turns off followed by the the "USB device not recognized" on my pc.
I hope this can be used as a hint towards reviving my device.
Regards
have you followed orbs advise above and pm a chef on that section, they maybe able to help. From my knowledge (limited on that device) i ddont think there is any recovery proceedure that you have not tried. Have u downloaded offical wm5 rom and tried it. I know and appreciate that it will probably not work due to corrupt bootloader, but what else is there to do??
To understand more, what did you do PRIOR to trying to flash to 6.5.
Did you hardspl correctly? Had you already flashed to another rom and just felt like flashing to another new rom?? Give us more detail.
Thanks for your reply
I dont know how to PM Chef.
I had used 3 other Rom versions of WM6.1 on my device. They ran very much fine on my device. But When i found WM6.5 xplode, I wished to try that too. But the rom update procedure went successfully till 99% and after that it showed an error that upgrade was not successfull. I pulled out the device and tried to restart if by all methods but I wasnt able to power on at all.
Thanks
Regards
ok, goto the thread that you got the rom off, click the chefs name and you will get a menu there to send pm, do it, he might have seen a similar problem or know how to correct bootloader.
good luck
noup really no...
Is bricked
my bro has bricked an Universal and the same led turns red no power off no bootloar no power it means the flash chip is dead!
Sorry to heard that.
He waits too long for the upgrade it tooks at least 40 minutes
then ERROR... but you know... the batt was died in middle process ( th batt was ****ed up, it say full charged but no! it was on 60 or 50%) then the stupid thing is make a hardreset.. i told him dont hR your device... justa simple reste and reinit the process... and huh! its bricked.
if you are interested on sell your parts
maybe my bro want some parts.
my advice(similar to other people):
1. Charge your batery somehow (in other device or anything else)
2. put your devce in bootloader mode and connect it to pc - it wll be detected like microsoft usb sync
3. use mtty try difrend versions becuse sometimes 1.42 does not detect it properly - read here for what to do with mtty
IMO this may be battery problem or nand chip problem - in both cases it is hardware fail
Hello guys!
I've got a bit of a problem here, because now my mobile refuses to connect with activesync and therefore making it impossible to flash it.
I read the readme in the cid bypass folder, and didn't quite understand it, but as keen as I was on getting a new rom I did it all wrong.
I actually copied the cid bypass folder to my sd-card and ran haret.exe from the phone. A friendly penguin appeared along with some green text, and it rebooted and went black. I waited for a while, but had no patience so I rebooted it again. But after this it has been impossible to connect it with activesync! I've tried hard reset and different computers but nothing works!
I'm hoping someone on this forum can help me!
best regards
Try this.
turn your phone off and press the camera button in then plug it into the USB port
you should get a multi color screen. If you do then you can flash.
But go here http://forum.xda-developers.com/showthread.php?t=330909
Go to where it says EDIT and follow what it says.
Oh and when a dos box opens up and ask you things just press the return key each time.
good luck
hey man, I tried reflashing the original rom to my vox, with the manualstyle sd card flash. So now it's flashed with the original rom, but still activesync doesn't work! anybody have an idea on how to make this right?
somebody tried running haret.exe from their phone, then flashing the Uspl with ruu flasher and then flash the new cooked rom?
My phone is not able to connect for flashing while in black state (after running harET), is it stupid of me to reboot it and start it by holding camera button while plugging it in to the computer? and then flash it with the ruu?
somebody please help me?
go into settings then connections then more till you see USB to PC
in there un-tick the box which says enable advaned network.
zipuz said:
somebody tried running haret.exe from their phone, then flashing the Uspl with ruu flasher and then flash the new cooked rom?
My phone is not able to connect for flashing while in black state (after running harET), is it stupid of me to reboot it and start it by holding camera button while plugging it in to the computer? and then flash it with the ruu?
somebody please help me?
Click to expand...
Click to collapse
I am confused..is it working or not? one post you say it is but you cant sink..then you say its not.????
and dont use the flash off the mem stick..use windows..
ok, sorry for making confusing posts! I'm just excited about getting it to work.
So here's the situation:
From stock phone used with exchange (turned off the exchange part before doing anything)
1. I ran haret.exe from my phone, and it rebooted into a "black state" after which I rebooted it again
2. I tried to connect it to my computer using activesync, to be able to flash, but it wouldn't connect. Activesync doesn't respond to my phone.
3. I flashed the shipped rom to my phone from my sd-card in good hope that it would reset the whole process, but it still won't connect to activesync.
So here's my problem; I want to flash a cooked rom to my phone, but I'm unable to connect it to my computer via activesync, what to do?
deuse said:
go into settings then connections then more till you see USB to PC
in there un-tick the box which says enable advaned network.
Click to expand...
Click to collapse
tried with both ticked and unticked, still nothing
Turn off your phone then keep the camera button pressed in at the same time plug it into the usb port
your should show diff colors on the screen..if so follow what it says in this link.
http://forum.xda-developers.com/showthread.php?t=330909
and do it from the pc not your mobile...
it's restored, but no activesync still
Is the cable you are using ok? or is it a new one you just got.
does windows see it when you plug it in? if so un-install active sync then reinstall it.
I'm having the same issue with Windows Mobile 6.5 ROM, activesync simply doesn't work ;/
ivanek666 said:
I'm having the same issue with Windows Mobile 6.5 ROM, activesync simply doesn't work ;/
Click to expand...
Click to collapse
Have you been into settings and un-ticked the box in USB to PC?
Also if you are trying to sync to office you must create a new partnership
google is your best friend.
I have no problems with sync in XP/Vista?windows 7 and office 2007
I am using FMs 1.1 WM 1.1
deuse said:
Is the cable you are using ok? or is it a new one you just got.
does windows see it when you plug it in? if so un-install active sync then reinstall it.
Click to expand...
Click to collapse
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
zipuz said:
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
Click to expand...
Click to collapse
Do the Hard reset .Then connect it to your machine.I hope this time it will work smoothly.
zipuz said:
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
Click to expand...
Click to collapse
Try this
open sync then at the top chose files then click on DELETE MOBILE DEVICE
see what happens..but post back if you fix it to help other people
yogusmilu said:
Do the Hard reset .Then connect it to your machine.I hope this time it will work smoothly.
Click to expand...
Click to collapse
I failed to mention that I've tried the hard reset as well, no luck.
I thought about the same thing Deuse, but there's no mobile device registered, so I'm not able to delete it.
It seems that you have tried every possible method! Anyway, my suggestion is install activesync in some other PC (friend's) and connect your phone there. See if it registers the phone. If it does then it is problem with the PC and not with phone. In that case, connect phone to PC and open controlpanel>System (icon)>Hardware tab>Device Manager Button in your PC. Unfold Network adapters and see if your phone is detected properly or it is detected with an "!" mark in "Unknown/Other device". If so, delete the device and disconnect phone. Reboot PC, reboot phone connect again and let the PC reinstall your device and see if it recognises your phone.
One more way (I think you might have tried this)- Uninstall Activesync and reinstall and connect phone.
By the way if your phone is not recognised in some other PC then it seems trouble with the phone.
Thanks.
Looks like your cable is faulty. Try activesync connection through bluetooth (for testing, ofcourse you cant flash from bt ).
parthabhatta said:
It seems that you have tried every possible method! Anyway, my suggestion is install activesync in some other PC (friend's) and connect your phone there. See if it registers the phone. If it does then it is problem with the PC and not with phone. In that case, connect phone to PC and open controlpanel>System (icon)>Hardware tab>Device Manager Button in your PC. Unfold Network adapters and see if your phone is detected properly or it is detected with an "!" mark in "Unknown/Other device". If so, delete the device and disconnect phone. Reboot PC, reboot phone connect again and let the PC reinstall your device and see if it recognises your phone.
One more way (I think you might have tried this)- Uninstall Activesync and reinstall and connect phone.
By the way if your phone is not recognised in some other PC then it seems trouble with the phone.
Thanks.
Click to expand...
Click to collapse
It's marked with an "!", will try it on my own pc next time I have it, worked there last time! if not, I'll have to live with
Hello guys please help I was trying to update my 02 XDA (Polaris) to a pcarvalo extreme ROM and I had reached 85 % then all of a sudden a power failure and I now am having a bricked O2 XDA that is stuck on HardSPL2 screen red,green,blue, white....now when i try to update due to no connection with activesync I can´t progress beyond the initial screen of detection... please please how do I put a ROM back on to the device???? Anyone please please
Thanks for all the help
Regards
Tariq
t_malik said:
Hello guys please help I was trying to update my 02 XDA (Polaris) to a pcarvalo extreme ROM and I had reached 85 % then all of a sudden a power failure and I now am having a bricked O2 XDA that is stuck on HardSPL2 screen red,green,blue, white....now when i try to update due to no connection with activesync I can´t progress beyond the initial screen of detection... please please how do I put a ROM back on to the device???? Anyone please please
Thanks for all the help
Regards
Tariq
Click to expand...
Click to collapse
Hi,
Check this...
http://forum.xda-developers.com/showthread.php?t=425922
Thanks to [email protected], I hope It's good for you...
Cheers.
Thanks but so far no success
Thanks but so far no success as its impossible despite killing all activesync processes to get MTTY active on USB. The XDA itself shows the change from serial to usb but the MTTY does not find it apparently as USB option does not become available.
Tariq
t_malik said:
Thanks but so far no success as its impossible despite killing all activesync processes to get MTTY active on USB. The XDA itself shows the change from serial to usb but the MTTY does not find it apparently as USB option does not become available.
Tariq
Click to expand...
Click to collapse
did you run mtty from vista or win 7.....??
best is win xp....
Tried running both from Win 7 and XP on another machine, it does not seem possible for MTTY to find the USB despite all wce processes and winrapi etc have been killed !
Any suggestions?
Thanks again for all the help
Tariq
t_malik said:
Tried running both from Win 7 and XP on another machine, it does not seem possible for MTTY to find the USB despite all wce processes and winrapi etc have been killed !
Any suggestions?
Thanks again for all the help
Tariq
Click to expand...
Click to collapse
ok...this i write in another thread...maybe it helps you....:
read this...post 12.....he write...Now i can enter in 3 colors. Make this:
http://forum.xda-developers.com/showthread.php?t=636170&page=2
Still not able to get MTTY to show a USB in dropdown menu ...???? Amazing despite ripping almost all processes out not possible to get MTTY to detect the XDA
Thanks anyways
Tariq
Have you dissabled usb connections in WMDC (windows mobile device center) what version mtty you using ? i had best results with mtty_0513_Test.exe, you can also use putty.
Thanks Mekrib
I had disabled the USB connection in WMDC and On activesync on the XP PC and i used MTTY v.1.42 as this was the only one i found. Perhaps your version might help.
As much as i understand there seems to be a problem for the windows envoirnament to recognize the device as a USB device in the state it is in, amazingly does the XDA it self seem showing appropriate USB message when connected and Serial when the USB cable is unplugged. I was thinking perhaps to find a pc where activesync was never installed and then install the MotoQ driver and then try to run this MTTY.
Bye the way a link to MTTY of your version a believe is a test version would be highly appreciated.
Thanks again all of you guys I feel i am not suffering alone.
My best salutations to you all
Tariq
mtty works with vista xp win7 , plug your phone into pc before starting mtty.
out of interest what task are you going to run with mtty?
Thanks again
Unfortunately still no success even with this version of MTTY and I even tried out on other PC´s where activesync was not installed. Apparently the problem is that the phone device is not recognized in any system as a new device or even as a device. Only solution I can think of is some way to have the device boot from SD card if there is some way of doing this. I tried the NAND thing but again there one either has to flash something or use MTTY in my case none of these options seem to work as I am not able to communicate with the device using a computer through even MTTY
If someone has any other idea´s I am willing to give it a go
Thanks again every1
Tariq
Hi there chris
I was hoping to do following:
SET 16 0
Task 8 (format)
Task 0 (boot)
Then hopefully device would boot as it does have the basic IO( Bios) eqvivalent doesn´t it?
Regards
Tariq
You can re flash just run ruupdate again, if it failed at 85% your rom wouldn't boot.Check in device manager if your phone is recognized properly otherwise you wont be able to flash.
Thanks Meknb
Thats the whole idea stopping flashing due to power failure at 85% has somehow made the device locked to going on to a boot till the tricolor screen with the info: Pola200 MPG , SPL-2.20.0linex CPLD-2
and serial/usb but no computer is able to detect the device.
I guess it has had it then...:-(
Respects
Tariq
Can't you copy your rom to your sdcard rename it polaimg and flash it that way?
Great Idea but with the original rom O2 (UK) and 2 pcharvelo roms it did not work and when the XDA boots I can barely see but it does in fact write no image found and the switches to the tricolor serial/usb picture
Maybe I have to get more info on exactly how the image file should be in terms of name and location and which rom file to use for the microSD.
Thanks I shall look for possible image files.
Thanks again
Tariq
POLAIMG all in caps at the root of your card should work.
Sorry Meknb but tried even that with caps and everything it still say no image found.
Thanks again
Tariq
Success
Yes Finally its alive again !!
Here is what I had to do:
Take the original O2/UK rom rename it to POLAIMG.nbh and place it on root of microSD card
Then and here is he important difference in what i was doing previously just press power button and it then detects the image and completes the reflashing of the rom.
Alhamdolillah (Thank god) I thought I had lost it
Thanks guys all of you and I hope anyone else who gets in my situation will benefit from this
Respects
Tariq