Related
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Drunknasty said:
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Click to expand...
Click to collapse
if your device is G3, unlocking is required to flash any rom, before upgrade your device, it is recommended to flash an official WM5.0 rom (in your case T-Mobile rom) with IPL and SPL 2.xx then flash again.
in general there are many probabilities for your issue.
((Where is TNT1.1?? did you mean 1.0?? ))
My Bad meant 1.0
So to get it straight.... I will need to unlock my phone each time?
Oh and to correct myself again, when flashing with the T-mobile ROM it says UPGRADE ONLY. And the read me file says its the wrong RUU. But it is the same file from Tmobile I used when I first got the phone. But I will try again.
Are there any other suggestions?
You need to read the "how to flash" sticky.
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Try another ROM.
Sounds like you need the "Wizard Love" rom. I dont have the link handy but I am sure someone else does.
Drunknasty said:
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Click to expand...
Click to collapse
Already got it. Thanks I am trying to load it now. But the only thing is that the last time it failed and I can understand what the error says. I know the number is 300 but can read the language.
But I will let you guys know when this load completes.
Thanks again for all the assistance.
No worky worky. The load completed and then boots the splash screen shows and then stays there.
Any ideas?
Try to remove the battery and let it out for at least half an hour. Then put it back in and see what it does then.
I thought the same thing too. So when it got done last night, out of frustration, I removed the battery and left it there to wait on when I get off work today. I will report back on what happens.
Again I would like to thank you guys for helping me. I really do appreciate it!
STEP 1 install the original manufacturer ROM
T-mobile UK
http://www.tm-phonedownloads.com/download_manager_mda_vario.html
T-mobile US
http://www.t-mobile.com/wmupgrade/
Search for the original rom for any other
instructions on how to use the original rom can be found here
http://support.t-mobile.com/knowbase/root/public/tm23294.htm?&A2L.SERVICE=AboutUpgrading
Put it in the bootloader mode.. ( three color screens )
hope this helps..
cheers
Praneet
Ok I did that and it gave me ERROR 296: UPGRADE ONLY
Then it tells me that the NBF file cannot be used for my PDA Phone. Please get newer NBF file.
Is there any way I can get the Tmobile splash and IPL\SPL number back to original, it doesnt need to boot all the way into WCE but atleast show the same numbers and splash during boot up?
Or any other way to get this thing to work?
Thanks guys
BTW it is a HTC Wizard from T-mobile.
If you are getting an error 300 you need a newer rom update utility, and regardless if your phone is a G3 or G4 it needs to be unlocked before you flash any rom.. LOAD a OFFICIAL cingular ROM onto your device before going any further, then unlock your phone either via www.imei-check.com or through some of the tools offered here...
Which one should I down load from Cingular? Even though I have a Tmobile phone?
what ipl and spl are you using and what radio are you using. Just post all the numbers from the bootloader
As soon as I get home, I will post them.
Thanks
Ipl 1.01
Spl 3.08
Thanks
Drunknasty said:
Ipl 1.01
Spl 3.08
Thanks
Click to expand...
Click to collapse
uh oh. someone tell me if I'm wrong, but I think this is bad. it's the result of flashing a g4 with g3 or the other way around... keep searching, and good luck.
flash the original t-mobile rom. your phone doesn't appear to be unlocked. good luck
I am in dire need of some help when it comes to flashing custom ROMs. It appears that I can no longer flash custom ROMs. I can successfully flash the official 1.62 ROM from HTC website, the dumped TILT ROM, the Kaiser dumped ROM, and the WM6.1 WWE 3.03.405.0_radio_sign_25.70.40.02_1.64.06.04, but any other ROM I can’t. Let me explain my meaning of not being able to flash a ROM. Once it flashes 100% and reboots, when the “Tap the screen to begin to set up your windows-mobile device” is supposed to be displayed, all I get is a blank white screen. If I touch my stylus to the screen the text shows up, but none of the colored pictures that suppose to be in the back ground. Every section of the setup just displays the text no background images. Even my today screen won’t display any background images.
Does anyone have any information on this? I’ve abused this thread http://forum.xda-developers.com/showthread.php?t=314615 like a cheap dirty whore trying to find a solution, but no avail. Any help will be GREATLY appreciated.
kjones2k1 said:
I am in dire need of some help when it comes to flashing custom ROMs. It appears that I can no longer flash custom ROMs. I can successfully flash the official 1.62 ROM from HTC website, the dumped TILT ROM, the Kaiser dumped ROM, and the WM6.1 WWE 3.03.405.0_radio_sign_25.70.40.02_1.64.06.04, but any other ROM I can’t. Let me explain my meaning of not being able to flash a ROM. Once it flashes 100% and reboots, when the “Tap the screen to begin to set up your windows-mobile device” is supposed to be displayed, all I get is a blank white screen. If I touch my stylus to the screen the text shows up, but none of the colored pictures that suppose to be in the back ground. Every section of the setup just displays the text no background images. Even my today screen won’t display any background images.
Does anyone have any information on this? I’ve abused this thread http://forum.xda-developers.com/showthread.php?t=314615 like a cheap dirty whore trying to find a solution, but no avail. Any help will be GREATLY appreciated.
Click to expand...
Click to collapse
are you using 6.1 radios or the 6.0 radios?
P1Tater said:
are you using 6.1 radios or the 6.0 radios?
Click to expand...
Click to collapse
For each ROM, when ever I flashed, it changed my radio. For instance Alex's 1.62 rom, when I flashed his ROM, it already to changed my radio to the need radio to 1.27.14.09
kjones2k1 said:
For each ROM, when ever I flashed, it changed my radio. For instance Alex's 1.62 rom, when I flashed his ROM, it already to changed my radio to the need radio to 1.27.14.09
Click to expand...
Click to collapse
some come with radios, but most dont. You have to be sure if you need an AT$T specific radio or not.
P1Tater said:
some come with radios, but most dont. You have to be sure if you need an AT$T specific radio or not.
Click to expand...
Click to collapse
When I was running the WM6.1 3.03 ROM with radio 1.64.X.X, I flashed to Alex 1.62 ROM and my radio changed to 1.27.X.X. Didn't this flash change my radio?
kjones2k1 said:
When I was running the WM6.1 3.03 ROM with radio 1.64.X.X, I flashed to Alex 1.62 ROM and my radio changed to 1.27.X.X. Didn't this flash change my radio?
Click to expand...
Click to collapse
yes, if those are the only two flashes you have done, then it sounds like you might have had the unfortunate luck of having a bad flash. Reflash again and see what happens.
Edit:
Did you also do a hard reset at the "tap here to begin screen alingment" screen? If not, always do so.
P1Tater said:
yes, if those are the only two flashes you have done, then it sounds like you might have had the unfortunate luck of having a bad flash. Reflash again and see what happens.
Edit:
Did you also do a hard reset at the "tap here to begin screen alingment" screen? If not, always do so.
Click to expand...
Click to collapse
I always hard reset when flashing new roms (learned alot in the kasier wiki). This is what I'm trying. Flashing to ATT 1.62 (Offical from HTC website) > manually flashing to 1.27.04.09 radio > Flashing to Alex's 1.62 ROM
Anyone else have any suggestions?
I have a few ideas that I think may help. PM me when you get a moment. It may Late saturday or sunday till I can get back to you, but I need to know a coupl of things. So, if you're still stuck, let me know.
GSLEON3 said:
I have a few ideas that I think may help. PM me when you get a moment. It may Late saturday or sunday till I can get back to you, but I need to know a coupl of things. So, if you're still stuck, let me know.
Click to expand...
Click to collapse
PM sent
Check out the ROM Upgrading section of the Kaiser wiki under 'Troubleshooting' to learn how to enter bootloader mode.
Assuming that you installed HardSPL the first time you flashed, once you've booted into this mode, reconnect your device to your USB cable and flash another ROM.
For those who haven't looked at the Kaiser wiki in a while, I've completely revamped it w/TOC pages to make it alot easier to use (shameless plug)
_Alex_ said:
Check out the ROM Upgrading section of the Kaiser wiki under 'Troubleshooting' to learn how to enter bootloader mode.
Assuming that you installed HardSPL the first time you flashed, once you've booted into this mode, reconnect your device to your USB cable and flash another ROM.
For those who haven't looked at the Kaiser wiki in a while, I've completely revamped it w/TOC pages to make it alot easier to use (shameless plug)
Click to expand...
Click to collapse
?? This is not my issue. I'm not a complete beginner when it comes to flashing. Ever since I flashed the WM6.1 3.03 ROM I haven't been able to flash a custom ROM without having an image problem. I can still flash OEM type ROMS without the image issue, but not custom ROMS. I have the problem with images once a custom ROM has been flashed. If more clarification of problem is needed, I am will to give it.
This may be extreme and largely untested, but have you tried 'clear storage' on the WM6.1 ROMs and chosen 'delete NAND' (or something to that effect)?
That should wipe your ROM memory clean, although I'm not sure if that would help or hinder your cause, as I haven't heard anyone try it yet...
Hope this helps!
_Alex_ said:
This may be extreme and largely untested, but have you tried 'clear storage' on the WM6.1 ROMs and chosen 'delete NAND' (or something to that effect)?
That should wipe your ROM memory clean, although I'm not sure if that would help or hinder your cause, as I haven't heard anyone try it yet...
Hope this helps!
Click to expand...
Click to collapse
No, I haven't tried, but I guess I'll give it try when I get back in town on thursday.
Sorry I had to bug out....
Alex, his problem is a little different than a RUUBNH error that's commonly seen. I tried walking him through a CE reset using MTTY & he can't even communicate with his bootloader. MTTY wouldn't establish a USB connection. I agree that formating the Nand may help, but I think you really should also try & reflash hardspl as well. I suggest the new version with AT command support. I have seen a few funky hardspl flashes that inhibit communication, although rare.
I didn't forget you though Kjones, & I'm trying to duplicate your problem & find an answer.
I have been searching all over for this but it's probaly right in front of my face. I read that you need to get rid of SPL.nbh from official ROMS before flashing back with HardSPL. The problem is, the official T-Mobile Wing ROM that I downloaded is an .exe file. How do I go about removing the SPL.nbh file since it doesn't display folder contents or anything, just runs the RUU?
Sorry for the double post, I realized I was in the wrong forum
flipside123 said:
I have been searching all over for this but it's probaly right in front of my face. I read that you need to get rid of SPL.nbh from official ROMS before flashing back with HardSPL. The problem is, the official T-Mobile Wing ROM that I downloaded is an .exe file. How do I go about removing the SPL.nbh file since it doesn't display folder contents or anything, just runs the RUU?
Sorry for the double post, I realized I was in the wrong forum
Click to expand...
Click to collapse
I'm uploading a zip file which will have the entire thing already to go.
Just flash your device as you would with any other rom.
Hang tight the link will be available within 10 mins.
Thank you sir. Greatly appreciated
flipside123 said:
Thank you sir. Greatly appreciated
Click to expand...
Click to collapse
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
One more question. I'm looking to keep HardSPL but I have to revert to original to upgrade ROMS don't I? I want to upgrade to your OT 6.5 ROM
flipside123 said:
One more question. I'm looking to keep HardSPL but I have to revert to original to upgrade ROMS don't I? I want to upgrade to your OT 6.5 ROM
Click to expand...
Click to collapse
Okay,
I thought you wanted to go back to the original T-Mobile rom.
If your trying to HARD-SPL your device to install one of my roms or another cooks roms then thats another story.
Please read my FAQ or one of the stickies.
Ok, I think I got it now. So I don't need to revert to the original ROM to flash it since I have HardSPL? Thanks for the help
wen i did this i think i bricked my fone now its at the tmobile screen and it jus staying there
I tried the file that you uploaded here...And it went thru the whole process of flashing the ROM, but after it updated my wing just stays on the T-Mobiel screen and never boots past that.
It had that open touch software on it and I don't want open touch. I want plan old WM 6.0 on there.
I called T-Mobile and got an offical 6.0 update from them, but when I try that one it gets to 1% then says it has a disconneted and I get a connection error.
ttran001 said:
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
Click to expand...
Click to collapse
So does this work? The two people who did this had problems. I need the phone to be all stock so I can have t-mobile send a free replacement because the screen is going on this wing.
***EDIT:*** Oka so this is the same as http://forum.xda-developers.com/showthread.php?t=364543&page=2 the first time I tried it it froze at 15% on step 2 so I installed the RAPI CAB like it says. Step two completed, phone rebooted and had white screen then I got error 260 I think. I have the stock t-mobile rom on it and had it on before I did this but it still has the yang from when I did a hard spl. Is there another way to get it to stock or am I doing something wrong? Plug in phone, let it sync, run herald-uspl.exe hit enter and so forth.
***EDIT*** Ok so this time it completed but is now stuck at the T-Mobile screen and I am now unable to even flash because I can't get past it And that damn yang still shows up in bootloader. Well went into bootloader and flashed from there so phone works but the damn yang is still there. And on a side note: Has anyone ever had a problem with their screen going very dark after flashing a rom from here? Phone was fine then I flashed OTP v7.4 TouchFlo 2D Lite.nbh yesterday and at night screen started going dark, would light up when opened in keyboard mode, then switched and then both were very dark and hard to see. I then flashed to OTP v7.3.1 TouchFlo 2D Final.nbh and still dark. Then I flashed to stock rom and have been able to see the screen since.
This is stupid easy to do... im shocked there isnt a post going into detail.
5 steps to going back.
http://forum.xda-developers.com/showpost.php?p=2998657&postcount=4
smokeingit said:
This is stupid easy to do... im shocked there isnt a post going into detail.
5 steps to going back.
http://forum.xda-developers.com/showpost.php?p=2998657&postcount=4
Click to expand...
Click to collapse
Did not work. Do I need to install the cab files again? I know I deleted a file out of the stock rom so it would not overwrite or verify or something but I put that file back, should I not have? This has been a few weeks and still can't get the yang off. Screen on my girls phone is almost dead, she can't even slide it any more so I need to fix the spl so I can send back to t-mobile....anyone ?
this is what i do to get back to the tmobile orginal. download the software from tmobile. I downloaded the newest update from tmobile site. REMOVE YOUR SD CARD. Connected my phone via usb. Launched the update. It has never failed me yet. It is just like updating your phone. tmobile has to take it, it is their update. They sent me a new phone noproblem, matter of fact i have to do it again, the back on the phone keeps getting loose on me. so they are sending me another phone again. hope this helps.
Alternatively you can use the combination of uspl and stock rom ruu to return your device to stock tmobile rom...
1. Enter in to uspl like you were falshing one of ttran001 roms... You can get this HERALD-USPL-beta3 from http://rapidshare.com/files/79249048/Flash_Center.rar
2. ONLY use steps 1 and 2 from the black screen (getting the white screen on your device)...
3. For step 3 in the flasher exit out of the black screen (windows cmd screen) by pressing ctrl+C...
4. Fire up the official ruu from tmobile found here http://forum.xda-developers.com/showthread.php?t=358030 or alternatively if you have a tmobile account still active you can get the most up to date rom from http://www.t-mobile.com/wmupgrade/
5. Fallow on screen instructions...
6. Back to stock rom...
Brick dopod C858
ttran001 said:
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
Click to expand...
Click to collapse
Hello freind,
I have been downloaded the above "Remove_HARD-SPL_On_The_Wing.rar" files and flash it to my Dopod C858 which has the Chiness language, I suppose to change the language from chinesse to Englis, After flashing the above files, now the phone is only in bootloader mode.
If you start the phone it will stuck on white screen and turn off.
Please help me how to revive my phone back.
Thanks and best regards
Jhemzz
Hey I'm having the same problem as most of these guys who tried the file. The phone just idles on the white Tmobile screen... does anyone know what to do or how to help?
Please and thank you!
angest90 said:
wen i did this i think i bricked my fone now its at the tmobile screen and it jus staying there
Click to expand...
Click to collapse
im having the same problem can anyone help me please?
hotsammysliz said:
im having the same problem can anyone help me please?
Click to expand...
Click to collapse
Being stuck at the Tmobile screen isn't a true brick. Just reflash your ROM. (If you're not HardSPL'd, reflash your RUU.)
Remove Hard SPL from bootloader
Hi,
Anyone out there knows if we can remove hardspl from bootloader of Wing. Problem is my mobile displays splash screen, then switch offs by itself. Its been quite some time that I have hardspled it and have been using it. But recently I am facing this issue, so I am trying to move to original RUU and try if it works.
So for that anyone knows if we can remove hardspl from bootloader, because I am only able to enter bootloader. Moreover I tried several original roms from Flash Center as well as through SD card as well, but still be SPL version is 4.70.yang. Anyone knows any other alternative.
Also, if anyone has faced similar problem then kindly advice how you resolved.
Thanks in advance!
Regards,
Pankaj
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
shawndh said:
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
Click to expand...
Click to collapse
Ick...this sounds like one of a couple of things...either you really screwed it up (btw, even "really screwed up" has been known to be fixable thanks to the super awesome folks here on XDA Devs) or it's a simple fix. My first suggestion would be to put it back into bootloader (just hold the usualy bootloader buttons and stick the stylus up in the Reset hole OR take the batter out and put it back in, your choice I think) and try rerunning everything EXCEPT the KasierUnlocker (btw, dont quote me but I would almost swear KaiserUnlocker needed a special radio flashed in order to properly work...you may wanna head back to that thread and check it out. I unlocked mine with it and I can about guarantee I had a special radio...) and see if it fixes anything OR find a compatible radio and reflash it (well, first off...get it into bootloader and tell us what the bootloader says on it)
Anyways, first things first would be to see what the bootloader is showing and then work from there. Sounds like a little bug so don't freak out too bad. If you think flashing these babies are hard then you really didnt try flashing G4 versions of the Wizard =P I totally bricked one because it was the pesky G4s and I didn't realize it at the time (complete newbness lol) So yeah, Kaiser's are a LOVELY change for me =] I've flashed mine countless times and loved it since the moment I got it! =D
But yeah, gimme info! =]
Did you use WM6.1 or WM6.0 to unlock the phone? Put in boot loader and flash orginal WM6.0 ROM as the other user suggested. You should be able to flash it if it is not a brick.
If it doesn't work you can use mtty to recover your phone, the needed information you'll find in the Kaiser Wiki.
Hope it helps
I just had this exact problem.
Use the EXE included in the tutorial to flash any windows 6.1 ROM from the bootloader via USB, and you will boot again.
HTCOmega said:
Ick...this sounds like one of a couple of things...either you really screwed it up (btw, even "really screwed up" has been known to be fixable thanks to the super awesome folks here on XDA Devs) or it's a simple fix. My first suggestion would be to put it back into bootloader (just hold the usualy bootloader buttons and stick the stylus up in the Reset hole OR take the batter out and put it back in, your choice I think) and try rerunning everything EXCEPT the KasierUnlocker (btw, dont quote me but I would almost swear KaiserUnlocker needed a special radio flashed in order to properly work...you may wanna head back to that thread and check it out. I unlocked mine with it and I can about guarantee I had a special radio...) and see if it fixes anything OR find a compatible radio and reflash it (well, first off...get it into bootloader and tell us what the bootloader says on it)
Anyways, first things first would be to see what the bootloader is showing and then work from there. Sounds like a little bug so don't freak out too bad. If you think flashing these babies are hard then you really didnt try flashing G4 versions of the Wizard =P I totally bricked one because it was the pesky G4s and I didn't realize it at the time (complete newbness lol) So yeah, Kaiser's are a LOVELY change for me =] I've flashed mine countless times and loved it since the moment I got it! =D
But yeah, gimme info! =]
Click to expand...
Click to collapse
I know. The crazy thing is that I've successfully flashed a G3 and a G4 Wizard and I still find this confusing.
When I go to the boot loader screen I have:
KAIS1*0
SPL-3.56.Hard
CPLD-8
When I reset the device normally I get:
R 1.27.12.11
G 22.45.88.07H
D 1.62.00.00
I didn't try to flash any other ROMS to unlock it. I just went with the hard SPL and then tried the Unlock tool. The phone is stock.
Thanx for the replys. I reflashed the original ROM and now it's working again. This is what I have now:
When I go to the boot loader screen I have:
KAIS1*0
SPL-3.56.Hard
CPLD-8
Now when I reset the device normally I get:
ROM version 1.62.502.0
Radio version 1.27.14.09
Protocal version is 22.45.88.07H
Device info:
Windows Mobil 6
CE OS 5.2.1622 (Build 18128.0.4.4)
Can I go strait to a SIM unlocker and then flash a new ROM?
Well you've got HardSPL 3.56 flashed to it.
Why do you need to sim unlock it? Sim unlocking is not neccesary to flash one of the many Roms avaliable for the Kaiser/Tilt.
Once it's got HardSPL flashed, you're free to flash any type of rom onto it
shawndh said:
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
Click to expand...
Click to collapse
A couple of things:
1) The Kaiser-Unlocker only works on 1.xx hardspl's, so you'll have to put one of those on first.
2) You do need to install the patched radio before you run it.
3) You'll need to flash a compatible radio afterward too, or else your device might not boot all the way.
4) Next time please post these questions in the thread for the unlocker you are using. It makes it much simpler for everyone.
stuff said:
Well you've got HardSPL 3.56 flashed to it.
Why do you need to sim unlock it? Sim unlocking is not neccesary to flash one of the many Roms avaliable for the Kaiser/Tilt.
Once it's got HardSPL flashed, you're free to flash any type of rom onto it
Click to expand...
Click to collapse
But HardSPL 3.56 doesn't SIM unlock the phone from what I understand. I need to use it with T-Mobile SIM. So I need to chenge to a 1.XX Hard SPL to do this?
So I guess I went wrong with flashing 3.56 first and not 1.1
Then I need to patch the radio
Run the unlocker
rinstall the radio
Then flash the ROM
Problem I have now is that I can't seem to go back down to a lower SPL version.
shawndh said:
But HardSPL 3.56 doesn't SIM unlock the phone from what I understand. I need to use it with T-Mobile SIM. So I need to chenge to a 1.XX Hard SPL to do this?
Click to expand...
Click to collapse
You need to read the instructions carefully, and ask questions in that thread. All the experts in unlocking will be there to help you.
Ok...so my tp2 is verizon and I did the whole hardspl thing and somehow got the energyrom leo on my fone, and then wen i tried to update to the new sense 2.1 extreme rom, i dont know wat happened. It said to use this custom ruu thing which i clicked on, and wen it updated my fone, my fone does absolutely nothing now cept loading the start screen where it says Touch pro2
I new something was wrong becus at no point was the .nbh that i extracted used, but no ruu came with the file that i downloaded...sighhh so is my fone dead or wat? I tried hard resetting, and although i am able to get to the hard reset page, wen i actually do it, it still just freezes where touch pro2 screen comes out
dont trip
i've 'bricked' most of my phones i've played with at least once. If your getting anything your ok - go to boot loader mode, reflash the original rom on it, then the one you want. Make sure your battery has a good charge also ^^
starscalling said:
dont trip
i've 'bricked' most of my phones i've played with at least once. If your getting anything your ok - go to boot loader mode, reflash the original rom on it, then the one you want. Make sure your battery has a good charge also ^^
Click to expand...
Click to collapse
ok so im uploading this rom rite now http://forum.ppcgeeks.com/showthread.php?t=91940..the verizon one, once i get that do i have to do the hardspl thing again? btw thanks so much for the bootloader thing, i didnt know how to do it, i kept doing the hard reset..lol
* i got the stock rom back, thanks alot...do i need to hardpl it again? could sum1 help me flash to the another rom as well, i just dont know wat to do wit the nbh
fjgotgame24 said:
ok so im uploading this rom rite now http://forum.ppcgeeks.com/showthread.php?t=91940..the verizon one, once i get that do i have to do the hardspl thing again? btw thanks so much for the bootloader thing, i didnt know how to do it, i kept doing the hard reset..lol
* i got the stock rom back, thanks alot...do i need to hardpl it again? could sum1 help me flash to the another rom as well, i just dont know wat to do wit the nbh
Click to expand...
Click to collapse
it wouldnt hurt. Just pretend youve never done anything to the phone.
Write or type out a list of steps for each phase
print it out and cross them off one by one.
thanks
Thanks my TP2 now is working
orobas said:
Thanks my TP2 now is working
Click to expand...
Click to collapse
sweet
just had the black screen of death - lol was like - THE THREAD OF DEATH CURSED ME :> [all good now of course]
Failed flashing with CustomRUU.exe
Every flash has failed (freezes at "Touch Pro2" boot screen) when I tried to use a ROM that uses CustomRUU.exe (Miri, Cell_Pro, Athine, AF, Shadowline, and others). Flashing ROMs that use ROMUpdateUtility.exe already extracted flash fine. I've even tried first flash the original Sprint stock ROM and then flashing a "CustomRUU" ROM but without success. I've also extracted the files from the CustomRUU.exe and then run it with the nbh file but that doesn't work either. HTC Touch Pro2 (Sprint)
Any suggestions?
-Scott
scottGx said:
Every flash has failed (freezes at "Touch Pro2" boot screen) when I tried to use a ROM that uses CustomRUU.exe (Miri, Cell_Pro, Athine, AF, Shadowline, and others). Flashing ROMs that use ROMUpdateUtility.exe already extracted flash fine. I've even tried first flash the original Sprint stock ROM and then flashing a "CustomRUU" ROM but without success. I've also extracted the files from the CustomRUU.exe and then run it with the nbh file but that doesn't work either. HTC Touch Pro2 (Sprint)
Any suggestions?
-Scott
Click to expand...
Click to collapse
You're flashing CDMA ROMs, right? Not the GSM only ones found here, but CDMA ones from elsewhere, like here? Try flashing one of the CDMA ROMs found at the second link, and see if that works, because I think you may be flashing GSM ROMs onto your CDMA device, which would explain why it flashes, but doesn't boot properly. Hope that helps
DaveTheTytnIIGuy said:
You're flashing CDMA ROMs, right? Not the GSM only ones found here, but CDMA ones from elsewhere, like here? Try flashing one of the CDMA ROMs found at the second link, and see if that works, because I think you may be flashing GSM ROMs onto your CDMA device, which would explain why it flashes, but doesn't boot properly. Hope that helps
Click to expand...
Click to collapse
Apparently, I was flashing a GSM ROM. There really should be better indication of what the ROM is designed for than simply being in a particular form. It wouldn't be any trouble to add a few characters (GSM/CDMA) to the file name to make it clear.
Thanks!
My Verizon tp2 is stuck on the TOUCH pro2 screen when it tries to boot.. It will not hard or soft reset. So it's not being recognized by my pc to do the hardspl thing. I was trying to flash the perfectblack rom but it said it was not for my device...so i tried Energy rom.. it flashed but will not boot.. please help...how do i fix this.
Well...I took it back to Verizon...they are sending me another one. Have to figure out what I did wrong because I truly wanted to try a cooked rom or two.
Back to the drawing board.
defiantone said:
Well...I took it back to Verizon...they are sending me another one. Have to figure out what I did wrong because I truly wanted to try a cooked rom or two.
Back to the drawing board.
Click to expand...
Click to collapse
Wait, you are sending Verizon your phone with a non-booting cooked ROM and the HSPL on it?!?
If they figure that out, there's a good chance you'll be SOL.
dwizzy130
dwizzy130 said:
Wait, you are sending Verizon your phone with a non-booting cooked ROM and the HSPL on it?!?
If they figure that out, there's a good chance you'll be SOL.
dwizzy130
Click to expand...
Click to collapse
Exactly. Even if you have insurance on the TP2, if you sent it back with anything that is not stock, your insurance is probably voided, they probably wont give you your phone back, and you might even have to pay full price for a new one. Good luck man. Definitely should have held out for some responses before you sent it out. If you haven't then that's good, but if you did, your probably out of luck.
defiantone said:
Well...I took it back to Verizon...they are sending me another one. Have to figure out what I did wrong because I truly wanted to try a cooked rom or two.
Back to the drawing board.
Click to expand...
Click to collapse
Why didn't you try what the orginal poster did?
I loaded a GSM rom on my Sprint TP2, I wasn't paying attention to the orginal
Post and just thought oh.. I want this rom..
What I did,
Turn on the device while holding down the Power button and the Volume Down key. If you see Serial and 3-4 colored bars plug in your USB, and reflash with a CDMA Rom.
This fixed my Phone. Credits to the gurus at PPC Geeks. if i find the topic later I'll post it.
*edit: nevermind
*edit: problem resolved