... since this problem is bugging us with aku3.x and crossbow roms.
Especially with the crossbow rom, this seems to be the only problem. The other issues are already fixed, or are easy to get fixed (since they have already been fixed in earlier roms).
In addition to this, I think that if we work together we have greater chances of solving this frustrating issue.
So this is what I have tried (with no success):
1) replace the battdrv.dll with one from a prophet
I get the common result where the device will charge only when you softreset with the cable inserted. You also get a square in the "Model No" in device information (Module address conflict?) Someone solved the square issue in an aku 3.x rom. I would like to know how it was fixed.
2) replace the battdrv.dll with one from an HTC artemis
No charging/status indication. Model No is reported as "WIZA200"
3) I unloaded camera and keyboard driver to see if there are any conflicts with them - no difference
andrew_sh said:
... since this problem is bugging us with aku3.x and crossbow roms.
Click to expand...
Click to collapse
A possible way is to write a wrapper for the batterydriver, which logs information and try finding the differences in pnp, etc.. between a working rom and a non working rom with the prophet-driver.
You could try following too:
- don't touch the batterydriver in original aku3-rom
- do following while device finished boot and os is running:
- copy battdrvr.dll from prophet and rename it to \windows\battdrvr_New.dll (into the new rom)
- change the registry-value HKLM\Drivers\BuiltIn\Battery\Dll = battdrvr_New.dll
- wait some minutes and do a softreset
-->it will not survive a hard-reset, but i guess this could solve module-overlapps..
hope this helps,
ikarus
ikarus said:
A possible way is to write a wrapper for the batterydriver, which logs information and try finding the differences in pnp, etc.. between a working rom and a non working rom with the prophet-driver.
You could try following too:
- don't touch the batterydriver in original aku3-rom
- do following while device finished boot and os is running:
- copy battdrvr.dll from prophet and rename it to \windows\battdrvr_New.dll (into the new rom)
- change the registry-value HKLM\Drivers\BuiltIn\Battery\Dll = battdrvr_New.dll
- wait some minutes and do a softreset
-->it will not survive a hard-reset, but i guess this could solve module-overlapps..
hope this helps,
ikarus
Click to expand...
Click to collapse
Thanks for the info.
I just tried it.
Result:
I get the square in the device info.
No charging/no battery status.
Strange isn't it? I wonder why the model no gets f**d up.
To my knowledge, "usbfn.dll" is involved as well, so maybe you gotta play around with that one as well...
MusicMike said:
To my knowledge, "usbfn.dll" is involved as well, so maybe you gotta play around with that one as well...
Click to expand...
Click to collapse
I tried replacing this file. The result is that activesync stops working completely.
MusicMike said:
To my knowledge, "usbfn.dll" is involved as well, so maybe you gotta play around with that one as well...
Click to expand...
Click to collapse
i do agree.. don't know which dll's, but maybe there are more dll's used for battery..
There is a tool called depends or similar, which can figure this out..
depends is part of free eVC++ (\Program Files\Microsoft eMbedded C++ 4.0\Common\Tools\depends.exe)
ikarus
ikarus said:
i do agree.. don't know which dll's, but maybe there are more dll's used for battery..
There is a tool called depends or similar, which can figure this out..
depends is part of free eVC++ (\Program Files\Microsoft eMbedded C++ 4.0\Common\Tools\depends.exe)
ikarus
Click to expand...
Click to collapse
ahh, thats a handy tool, thanks for the tip !
attached is a cab which could fix this issue.
my contribution to the great work of our rom-cooker
ikarus
ikarus said:
attached is a cab which could fix this issue.
my contribution to the great work of our rom-cooker
ikarus
Click to expand...
Click to collapse
Thanks ikarus, i'll try tomorrow.
So have you tried this? Did you find out what was causing the problem?
andrew_sh said:
So have you tried this?
Click to expand...
Click to collapse
MusicMike tested it, but it needs more testing hehe
andrew_sh said:
Did you find out what was causing the problem?
Click to expand...
Click to collapse
not yet... in part yes, but i don't want to write explanations which could turn out to be wrong...
I'm back, testing it now
Jesterz said:
I'm back, testing it now
Click to expand...
Click to collapse
Welcome back! hehe damn it's been a long time
HELP
okay i have the japnease wm6 rc7 both files its all in jap appantly the battrey issue is fixed and all the other problems can someone help me to convert the language into english and then i can test on my prophet we may have a fully working wm6 rom here guys please need help for final stages.
WM6 100% working on prophet
Hi i just installed wm6 rc7 and i can confirm usb charging and sound all works on prophet flawlesly i need a hero to covert the language into english please can someone help
c3l5o said:
so I was just wondering what does the app change in my phone to make it work... I didn't eve have to soft reset it once...
Click to expand...
Click to collapse
jutley said:
Hi i just installed wm6 rc7 and i can confirm usb charging and sound all works on prophet flawlesly...
Click to expand...
Click to collapse
great. i have some thoughts about the cause, but i don't have an verified explanation for the cause.
Actually i don't have enough time to do more investigation for... So i can explain what the cab is doing.
It's a very slight solution.
The cab creates a notification for the "Notification Broker", which in turn starts XDADev_BatFix.exe each time usb gets connected.
(That is there is no extra thread running, there is no dll loaded, there is no system service running and no extra resource needed. It is almost like before.)
XDADev_BatFix.exe does only set a PowerEvent and exits afterwards.
that's it.
Best regards,
ikarus
anyone sucess pls post...
i'll try tomorrow
ikarus said:
great. i have some thoughts about the cause, but i don't have an verified explanation for the cause.
Actually i don't have enough time to do more investigation for... So i can explain what the cab is doing.
It's a very slight solution.
The cab creates a notification for the "Notification Broker", which in turn starts XDADev_BatFix.exe each time usb gets connected.
(That is there is no extra thread running, there is no dll loaded, there is no system service running and no extra resource needed. It is almost like before.)
XDADev_BatFix.exe does only set a PowerEvent and exits afterwards.
that's it.
Best regards,
ikarus
Click to expand...
Click to collapse
Ok thanks ikarus! Really is a smart and slight solution
guitarz said:
anyone sucess pls post...
i'll try tomorrow
Click to expand...
Click to collapse
It IS working indeed
This fix tested and working on Qtek S200! Its one of the 2,2 clean roms from a few months ago. The battery problem has been my biggest annoyance! Thanks!
I also tried XDADev_BatFix on my 818Pro with AKU3.3-Jester-b1 ROM.
Looks like it really solve the battery charge problem.
Thanks ikarus!
Worked
It Worked on I-mate JamIn, Thanks.
some times the device do not wake up after it sleeps
Related
KitChenROM Core 5.2.1908 Build 18508.0.7.0 :
New OEMs :
1. HTC Home New Version (Show HTC Home in Today)
2. Skin WMP.
3. PP=6MB
http://rapidshare.com/files/5396981...CTAIVOI_Core_1908_Build_18508.0.7.0_PP6MB.rar
Good stuff! Thank you . But can anyone share a mirror? Rapidshare's just really too slow!
Great! Thanks
Great job! Thanks.
Just a small note: the version of esmertec java is a bit outdated 20070425. I can prepare a OEM package with 20070802 if you want.
Thanks again
PS: has this rom been completely ported, i.e. all dll rebased and so on?
Great thanks boy_de_ghet great job!!
risidoro said:
Great job! Thanks.
Just a small note: the version of esmertec java is a bit outdated 20070425. I can prepare a OEM package with 20070802 if you want.
Click to expand...
Click to collapse
OK, it seems that the files in your oem package (2007_04_25) and the ones i got in this forum (2007_08_02) are the same. The only differences are in the registry keys, i don't know which keys are the correct ones but i suspect that the ones in your oem package cannot work since they associate jad and jar files with \windows\joedek.exe but there's no such file in \windows. The correct association is with \windows\jbed.exe. Your oem package will probably run ok but it won't let you start midlets installation right from the browser/file manager.
I'm attaching a slightly revised OEM package with correct file association, a link to jbed help in \windows\help and some missing png files added to initflashfiles.dat
Bye
thanks!
...time to light the fire
great job, as usual!
Can you provide some more info?
Which applications are added?
Screenshots?
Thank you very much!
risidoro said:
Great job! Thanks.
Just a small note: the version of esmertec java is a bit outdated 20070425. I can prepare a OEM package with 20070802 if you want.
Thanks again
PS: has this rom been completely ported, i.e. all dll rebased and so on?
Click to expand...
Click to collapse
This KitChenROM haved Esmertec Jbed 20070802.
boy_de_ghet said:
This KitChenROM haved Esmertec Jbed 20070802.
Click to expand...
Click to collapse
Yep, i realised soon after my post. The registry settings however are incorrect (they reports version 2007-04-25 and associate jad/jar to jeodek.exe instead of jbed.exe)
Great work BTW! Thanks
is it real QVGA version of AKU0.7.0 or mix of Universal's VGA AKU0.7.0 with older QVGA resources?
I've just flashed a new rom made with this kitchen. It is BY FAR the fastest rom ever tried!!!
BUT THERE IS A GREAT problem: i cannot access any SIP input methods from any application. All the SIPs (keyboard, letter recogniser and block recogniser have vanished).
EDIT: no more a problem, it went away after a soft reset
i did not read whole post.
i have one question, that "someone" could answer to...
HOW the hell use OLD commgr and OLD dialpad in that one.....i need 100% method for REPLACEMENT of these.
also - how to implement OLD no(fockin) touch touch driver...
I ran the buildos.exe but after finish, I don't see the 80040000-OS.nb in the temp folder anywhere. There's a dump file with all the stuff in it. Gimme a clue someone.
run the CreateRom.bat file...it should be in the same directory with the BuildOS.EXE
thanks, it works now.
problems
i built a rom with this kitchen and after i built it and flashed it to my wizard it will start to boot up for the first time and it will get to where u calibrate the screen and turn itself off and restart...in a endless cycle....this isnt hte only time ive had this problem its happened with other kitchens...i just dont know what the problem is...or how to fix it.....any ideas? any help would b great appricated! thanks!
jug6ernaut said:
i built a rom with this kitchen and after i built it and flashed it to my wizard it will start to boot up for the first time and it will get to where u calibrate the screen and turn itself off and restart...in a endless cycle....this isnt hte only time ive had this problem its happened with other kitchens...i just dont know what the problem is...or how to fix it.....any ideas? any help would b great appricated! thanks!
Click to expand...
Click to collapse
We need to know exactly which options did you enable and which not.
my bad ur right hmm let me see
i deleted(not non selected but actually deleted from the oem folder)
EsmertecJava
Eye on Privacy
Hibernate
Camera
and then added my own oems
coolcam
wm6 Palm Threader
all other options were enabled
palm threader i made myself but i know it works bc ive used it b4...the issue might b with the coolcam...or that i deleted the oems....idk...but ive had this issue b4.
thanks for ur help!
jug6ernaut said:
my bad ur right hmm let me see
i deleted(not non selected but actually deleted from the oem folder)
EsmertecJava
Eye on Privacy
Hibernate
Camera
and then added my own oems
coolcam
wm6 Palm Threader
all other options were enabled
palm threader i made myself but i know it works bc ive used it b4...the issue might b with the coolcam...or that i deleted the oems....idk...but ive had this issue b4.
thanks for ur help!
Click to expand...
Click to collapse
Use the kitchen and don't delete anything or add anything. If that ROM works, start by removing the stuff from the OEM folder and build again. If that works, then you know the problem lies with one of your custom apps.
jug6ernaut said:
my bad ur right hmm let me see
i deleted(not non selected but actually deleted from the oem folder)
EsmertecJava
Eye on Privacy
Hibernate
Camera
Click to expand...
Click to collapse
DO NOT REMOVE CAMERA!!!
It's not a clean package, it includes also some files and reg settings needed elsewhere in the rom. The other packages you listed can be safely removed. bye
After I updated to latest ROM from Ranju (Build 4), all was fine and the camera was working great. Then I inserted my 2GB SDcard and I had trouble with it, so I installed the rollback SD driver from Ranju post. My SD card is fine now, but my camera is broken, the image and the pictures I take is all blurry and full of interferences, and if I sitch to the front camera, I get one system error and my Qtek 9000 reboots.
Anyone has this problem or know how to solve it?
No one has any solution for my problem?
RRibeiro said:
No one has any solution for my problem?
Click to expand...
Click to collapse
I am currently looking into the issue myself and will post when I have found something.
Hope that helps,
-Jwrightmcps
Thanks, I hope you find a solution soon.
Many times I get some error about no buffer space and then my Qtek reboots.
install the hdsc patch
I have installed that I still the same problem.
i´m having the same problem with the camera....
RRibeiro said:
Many times I get some error about no buffer space and then my Qtek reboots.
Click to expand...
Click to collapse
I also have that problem often. It looks like it appends when the memory is low.
Can someone post the Cab or link to download the Universal camera cab for me to reinstall and see if works?
Thanks
I found it, I found the problem.
I had the processor speed aplet set to 624 mhz (Turbo mode), I turned off this option and got back to standard processor speed, and now my camera is working great.
But the Camera buffer problem is still there.
Well , I spoke too soon.
Everything was fine but all interferences and bad image of the camera came back like magic, I don't know why.
System error w Notes app
Jwrightmcps said:
I am currently looking into the issue myself and will post when I have found something.
Hope that helps,
-Jwrightmcps
Click to expand...
Click to collapse
I don't know if this can help, but I got the same system error writing a note with the standard notes application (no OneNote)
Marco.
RRibeiro said:
But the Camera buffer problem is still there.
Click to expand...
Click to collapse
try to this solve
unzip attached file then copy it into \Windows\Start Menu\Programs
then sofreset.
longnguyen30 said:
try to this solve
unzip attached file then copy it into \Windows\Start Menu\Programs
then sofreset.
Click to expand...
Click to collapse
How this should help? It's just a (wrong) shortcut!
Marco.
I have a problem with Quick GPS: It doesn´t update (I tried activesync, Wifi, 3G,...): "Connection error. Try again later"
any solution?
Thanks
Carolan said:
I have a problem with Quick GPS: It doesn´t update (I tried activesync, Wifi, 3G,...): "Connection error. Try again later"
any solution?
Thanks
Click to expand...
Click to collapse
The same for me!!!! (since a few days)
I'm waiting for a solution too....
THX
Solution that worked for me
You can load and run again the original cab attached here.
You can do it from your sd but remember to install it on the device. Soft reset and ...done!
milpap said:
You can load and run again the original cab attached here.
You can do it from your sd but remember to install it on the device. Soft reset and ...done!
Click to expand...
Click to collapse
Thanks for the tips. Unfortunately I can't install this Cab on my Polaris because the system inform me that this application isn't signed.
Any tips to bypass this problem ?
Thanks in advance
Try to install it when Polaris is not connected with pc.
milpap said:
Try to install it when Polaris is not connected with pc.
Click to expand...
Click to collapse
It is exactly what I've do (before reading your answer ;-) ).
It run perfectly (after a restart of the Polaris).
Thanks for the tip!
Unbelievable milpap!!!
It's work for me too...!!!
I have killed the process just before installing the cab, soft reset, and it's working now!
But where was the problem???
From Spain, thank you very much !!!, milpap
Works for me too
Fix using Registry
[HKEY_LOCAL_MACHINE\Software\HTC\QuickGPS]
"RemindTime"="02151010034724"
"Bias"=dword:fffffed4
"ExpiredTime"=dword:00002760
"folder"="\Windows\"
"region"="GB"
"INIDate"="20060531"
"remind"=dword:00000001
"actSync"=dword:00000001
"auto"=dword:00000000
"NotifyID"=dword:00001960
"INIFile"=""
"path"=""
"EEFile"="xtra.bin"
"curRegion"=dword:00000000
"curIP"=dword:00000000
"pwd"="1"
"authname"="1"
These registry settings will also correct the issue...
thanks
It worked, thank you very much!!!!!
Now workin`
Hey Guys!
After i read the post and updatetd my xda the QuickGPS Update runs like never before!
The O2 Germany Support was unable to fix my prob, so thanks to the Forum!!
Quick GPS
Same problem here, it works again, thanks!
Am i special?
Hey Guys...
I updateted the htc_quickgps.cab and restartet my device.
After one day the update ended with the old errormessage.
I dont know the reason, does anybody else?
best regards
Frank
btw:
I cant see any difference in the reg.-settings so i dont change anything
Quick GPS
Thanks a lot! I had the same problem and this solved it.
Hi,
I also had major problems with my QuickGPS (using a Polaris, which seems to be a little special in this concern).
After many days of research and finally a lucky hit at htc customer support I can tell you this:
You have to install some sort of navigation software, install a map, activate and soft reset before using quick gps the first time. if you dont, you screw up the registry and will always have problems with qgps!!
maybe some hints are helpful (they werren't for me), but I would not want to reinstall or change registry settings all the time.
Reason: The navigation software sets up qgps for its needs. qgps seems to be by far more than a simple download manager for ephemeris data. if you dont have a working navigation software, quick gps will start going wild
In case you will have problems later on: try uninstalling tomtom - soft reset - installl - soft reset and press thumbs
maybe a regular backup can help as well, we will see.
Wish you best of luck...
Thanks for cab, it works for me too !!
Mulb
Only Bepe 0.67 fixed it for me
Hey Guys!
I flashed my Device with Bepes 0.67 and now the update is running witout any problems.
Once again thxs to bepe!
Frank
There's a very easy fix which works for me. I see this problem from time to time on my device too. I am still unable to trace the "bad" software which replaces this registry key!
Just import the attached registry file every time you see the problem is back
Dmitry N said:
There's a very easy fix which works for me. I see this problem from time to time on my device too. I am still unable to trace the "bad" software which replaces this registry key!
Just import the attached registry file every time you see the problem is back
Click to expand...
Click to collapse
Thank you so much for this registery file...My problem was its update was only good for 1 day & 21 hours...It seemed strange to me & believe me I've tried everything & still didn't work right...Now with this registery file, update is good for 6 days....
at me this mistake. he managed to repair it. I say thank you for it
Hello, just received my HD2 ! But with trying to install some software, it mentions the certificates are not ok, so I cannot install. Is this the 'application lock' and how can I unlock it ?
MattRob said:
Hello, just received my HD2 ! But with trying to install some software, it mentions the certificates are not ok, so I cannot install. Is this the 'application lock' and how can I unlock it ?
Click to expand...
Click to collapse
Using a registry editor, set the following values:
Code:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]
"00001017"=dword:00000090
"00001005"=dword:00000028
"00001001"=dword:00000001
"0000101b"=dword:00000001
"0000101a"=dword:00000001
That should fix it... If the registry editor gives you an error, or you'd rather not use a registry editor, I can whip up a cab/program to do it.
Hm .... I tried that (with the old regeditSTG; but is not working very smooth) but still the same problem. I will try and install another regeditor, to see if that works ... Txs for quick follow up.
I tried it another time, but values seem to be correct now. Still have the application lock issue ... Would you mind making a cab, just to make sure ... ?
MattRob said:
I tried it another time, but values seem to be correct now. Still have the application lock issue ... Would you mind making a cab, just to make sure ... ?
Click to expand...
Click to collapse
Did you soft reset the device?
Yep, a few times already ....
MattRob said:
Yep, a few times already ....
Click to expand...
Click to collapse
Okay... I'll have a look at other things that could be set... What's the exact error it gives?
Unfortunately it is the Dutch version (that one arrived one week earlier here than the UK version), but after installing the software (which I used on my HD (with Dutty's Leo R7 and ALL earlier versions) and I need it to get my server ready for my work exchange server), it says (translated):
The file cannot be opened. It is not signed with a trusted certificate or one of the components cannot be found. U have to install it again or repair it if the problem persists.
MattRob said:
Unfortunately it is the Dutch version (that one arrived one week earlier here than the UK version), but after installing the software (which I used on my HD (with Dutty's Leo R7 and ALL earlier versions) and I need it to get my server ready for my work exchange server), it says (translated):
The file cannot be opened. It is not signed with a trusted certificate or one of the components cannot be found. U have to install it again or repair it if the problem persists.
Click to expand...
Click to collapse
I think that's an issue with the cab/software rather than the certificates... Out of interest, what application is it?
If that would be true, I REALLY have a problem. It is not a 'known' software, I guess. It has been prepared by my company and I have to install it first before I can use our Exchange Server (through Domain Enroll). It is call gprschange.exe
It worked on all former HD Roms and on the XPeria. I will try to set up Exchange server without it. Hopefully it will work .... Will let you know ...
It is not working now ... I cannot connect to Exchange server ... I assume it cannot have anything to do with the 'Dutch' version ? That would be strange, right ? But I cannot understand it worked on all the HD ROM versions, and here it is not working .... And I was so happy I got the HD2 today and now it is not working (for me at least) ...
i don't know if you already have solved the problem, but in some cases, when a cab refuses to install on my tp2, i open it with the wince cab manager on the desktop, remove the setup.dll and repack it again. It might not make any sense at all, but at least you can try it to rule it out.
May be something related to old .net 2?
or have you updated to 3.5 already?
hyellow said:
i don't know if you already have solved the problem, but in some cases, when a cab refuses to install on my tp2, i open it with the wince cab manager on the desktop, remove the setup.dll and repack it again. It might not make any sense at all, but at least you can try it to rule it out.
Click to expand...
Click to collapse
It was the setup.dll causing issues, it's fixed now!
Will move this to Leo Themes and Applications.
i have exactly the same problem with anumber of cabs that worked fine on my touch pro. seems a number of former reg edits are not being picked up as before. the keys i want to change for default folder locations don t work eiter...(see my post)...
oh, that is good...
thanks hyellow ...
Anyone knows about android iGo for polaris (QVGA)?
it looks like that it's working...
but haven't really tested so far
Sorry but
Hi,
Not yet for us. It's only usable in 320*480 !
See here
Cheers.
douceka said:
Anyone knows about android iGo for polaris (QVGA)?
Click to expand...
Click to collapse
manu33xtro said:
Hi,
Not yet for us. It's only usable in 320*480 !
See here
Cheers.
Click to expand...
Click to collapse
there's a "fix" to change the resolution down to 240x320 (data.gro)
i've tried it and it works so far, just the maps wont work with the wm igo8 version
have to look now for some new maps!
Hi,
Data.gro ?? Where is this file ? I can't find it in android folders...
Can you share it ? And explain to us how to use it : I've android with haret solution
Thanks in advance.
Cheers.
scripttec said:
there's a "fix" to change the resolution down to 240x320 (data.gro)
i've tried it and it works so far, just the maps wont work with the wm igo8 version
have to look now for some new maps!
Click to expand...
Click to collapse
hi,
attached you can find the modified "data.gro" file.
as your pola should already be rooted , there should be no problem by changing the file.
just copy the file with adb to the device.
afair the path on the device was something like "/app/app/com.navngo.igo.javaclient/ ... "
currently working under wm again, so can't tell you the exact path
have fun with igo on android
so far i've experienced the best usage with "lcd.density=100" in the default.txt
ooh and btw.: maps of igo8 version r3 are working!!
can't see the file in my phone...
Ok. Thanks. I saw it in Warez forum...
But I can't see anything maybe because I use with Haret ?!? I've a data path but nothing in
I don't know why...
scripttec said:
hi,
attached you can find the modified "data.gro" file.
as your pola should already be rooted , there should be no problem by changing the file.
just copy the file with adb to the device.
afair the path on the device was something like "/app/app/com.navngo.igo.javaclient/ ... "
currently working under wm again, so can't tell you the exact path
have fun with igo on android
so far i've experienced the best usage with "lcd.density=100" in the default.txt
ooh and btw.: maps of igo8 version r3 are working!!
Click to expand...
Click to collapse
scripttec said:
hi,
attached you can find the modified "data.gro" file.
as your pola should already be rooted , there should be no problem by changing the file.
just copy the file with adb to the device.
afair the path on the device was something like "/app/app/com.navngo.igo.javaclient/ ... "
currently working under wm again, so can't tell you the exact path
have fun with igo on android
so far i've experienced the best usage with "lcd.density=100" in the default.txt
ooh and btw.: maps of igo8 version r3 are working!!
Click to expand...
Click to collapse
Thx for help.
I've found the file, replaced it, igo seems to start correct resolution. However it terminates for unknown reason after license agreement screen
I tried igo my way for android
and data.gro is supposed to go in
data/data/com.navngo.igo.javaclient/data.gro
but I don´t even have com.navngo.igo.javaclient directory
SUCCESS!!!!!!
have to use root explorer in order to copy data.gro
iseeka said:
SUCCESS!!!!!!
have to use root explorer in order to copy data.gro
Click to expand...
Click to collapse
What version of igo do you have?
douceka said:
What version of igo do you have?
Click to expand...
Click to collapse
IGO myway 8.4.2.124036
i have to say that i said success at home without gps
tried this morning outside 1min no fix
i´ll try this afternoon and will let it more time to see if i get a fix or not
I tried again and i got a quick fix
tried also to plan a route and ok
later i´ll try if it warms speedcams
Hi,
Success for me too.
Just a little problem because I can't see all of the informations in down of the screen (speed for example) If I tap the screen in place of the speed information (I see just the up) I have the popup with speed but not the all ...
Is the same effect for you ??
Cheers.
iseeka said:
SUCCESS!!!!!!
have to use root explorer in order to copy data.gro
Click to expand...
Click to collapse
manu33xtro said:
Hi,
Success for me too.
Just a little problem because I can't see all of the informations in down of the screen (speed for example) If I tap the screen in place of the speed information (I see just the up) I have the popup with speed but not the all ...
Is the same effect for you ??
Cheers.
Click to expand...
Click to collapse
yes.. i guess data.gro has to be improved...
some ppl make a mod in order to hide and use the space of the top bar... maybe is possible to do it in our polaris and fix it...haven´t tried
If I've time I take a look...
Thanks for the answer
iseeka said:
yes.. i guess data.gro has to be improved...
some ppl make a mod in order to hide and use the space of the top bar... maybe is possible to do it in our polaris and fix it...haven´t tried
Click to expand...
Click to collapse
Success finally!!
The problem was somewhere in Win Mobile Content. Now I'm using only few maps, no pois etc. And it works great...
any success in running it on 240 x 320?
I'm using the attached data.gro file, but the language selection is all messed up...
Offtopic:
IGO is design for higher resolution that we have.
Replace data.gro - is the right way to get it running, but at the end result not good. Icons are messed up a little bit.
The other thing - stability. IGO hanged after about 1/2 hour of usage. Phone hangs, only reboot helped. Maybe it was issue of the relise I used. Can anyone post a comment on usage stability?
Right now using Sygic - for me seems much better solution for the moment. Only issue - positioning can take up to 5 minutes.
Hello, I have the HTC Wildfire, downloaded Igo but were exactly I need to place the data.gro file? Tried in to data in the phone not on the SD and it won"t let me copy it, can some one HELP, I really need Igo for my trip. Thanks a lot