Related
While a lot has been written, the following should provide an easy-to-follow guide:
Preparation:
1. A torch (read on and you will know why)
2. 256M SD card
3. Download ntrw.exe, romupdate.exe, hexedfull.exe from the ftp of this forum to c:\ and install hex editor
4. Download the appropriate ROM file (hereafter referred to as "newrom.nb1").
5. Cancel USB in ActiveSync
6. Use Sprite Backup to backup your ppc
Backup original ROM:
1. Put pocket pc into the boot loader mode (hold both on/off and camera buttons at the same time while resetting).
2. Insert empty SD card.
3. Connect pocket pc to pc through USB.
4. Run romupdate.exe on pc.
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
6. Don’t get panic to see the pocket pc screen goes dark. Use your torch and you will see the download percentage. Wait until it reaches 100% and shows “CheckSum is OK!”.
7. Insert SD card into card reader of the pc. Ignore the “format SD card” message and click “No”.
8. Run “command” to go into DOS prompt and change to root directory (cd c:\). Enter “ntrw read oldrom.nb1 s:” where s is the drive of your SD card.
9. Ignore the “Data error <cyclic redundancy check>” message. You should save another copy of this important rom file “oldrom.nb1”.
Change header of newrom.nb1:
1. Right click on oldrom.nb1 to open hex editor. Copy the first 416 bytes.
2. Open the downloaded newrom.nb1 file and overwrite the first 416 bytes with those of the old rom.
3. Save the edited newrom.nb1. You may save another copy of this important file.
4. Go to the command prompt and enter “ntrw write newrom.nb1 s:” to write it to the SD card. Ignore the error message “The parameter is incorrect”.
Update the ROM:
1. Insert SD card into pocket pc and put it to boot loader mode again (on/off + camera + reset). Use you torch to check the dark screen.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your pocket pc.
4. You may have to reinstall your software, unless you are familiar with the advanced features of Sprite Backup.
Ask you a question.
Does it backup 3 parts of rom (OS rom, extended rom and Radio rom)?
I am trying to backup my old Qtek Rom so I can install an update. I follow the steps to perfection..
The file created by ntrw is 999Mb big and at the end of the file I get an error stating that "parameters are incorrect"
Does this mean that the backup was not done successfully?
Why is the file so large?
Thanks for your help
ntrw get image SD card. Use SD card 256 Mb.
SD Card update problem
Hi I used ntrw.exe to backup my original rom to an SD card. It all went ok and I was able to clear the SD, write the rom back on the SD and put it in my M500. Normally I got a menu to press the power button to flash the rom to my phone, but now whatever I do I can't get the menu back. I won't get the option "Press power button" to flash. What I also see is that somethimes when I put the SD back in my laptop it is totaly empty. Normaly it would ask me if I want to format the SD because it can't be read. Can anybody help??
Thanks!
Dear All,
this is my first time to this site.
Could you please send me the download links for the files that are necessary (or the files themeselves) to backup the ROM (ntrw.exe, romupdate.exe, hexedfull.exe )
Thanks a million.
Will
i found this http://www.ccoo.net/MDAFlash/ntrw.exe
Thank you for this wonderful guide !!!
I am trying to backup my I-Mate JAM's ROM with a 256 MB SD card. However I have a similiar problem where when the ntrw.exe completed with the same "parameters are incorrect" error. The created ROM image is about 247,040 KB.
Is this correct? I did make sure the SD card is empty before the backup process (by deleteing everyfile on it), or should I use some proper method to ensure the SD card is actually completely empty?
Thanks in advance for any help!
Mine came up with that every time, but worked ok. I am trying to do the Anasky ROM update to my magician, and the backup i made of the original rom was fine to restore, even though i got that error.
mitchello said:
Mine came up with that every time, but worked ok. I am trying to do the Anasky ROM update to my magician, and the backup i made of the original rom was fine to restore, even though i got that error.
Click to expand...
Click to collapse
Thanks a lot for this info! It certainly make me feel a lot more confident about what I am doing
Thanks again !
Jyhnc said:
Thank you for this wonderful guide !!!
I am trying to backup my I-Mate JAM's ROM with a 256 MB SD card. However I have a similiar problem where when the ntrw.exe completed with the same "parameters are incorrect" error. The created ROM image is about 247,040 KB.
Is this correct? I did make sure the SD card is empty before the backup process (by deleteing everyfile on it), or should I use some proper method to ensure the SD card is actually completely empty?
Thanks in advance for any help!
Click to expand...
Click to collapse
someone in this forum told us that the rom size is vary and closed to the size of your sd card.
I used 128mb to backup and restore, it worked fine.
Has anyone experienced the problem of trying to reflash the device with the SD and when placed in Bootldr, the display just says serial and never progresses to press power to flash??
thanks
Jim
turn off the USB connection in your activesync, it will interfere the upgrade.
Found the fault, I reconnected the USB whilst entering the bootldr with the SD in socket and worked fine... Quite strange though as I couldnt remember having the USB connected the lasst time I performed the process
rgds
jim
jfran said:
Found the fault, I reconnected the USB whilst entering the bootldr with the SD in socket and worked fine... Quite strange though as I couldnt remember having the USB connected the lasst time I performed the process
rgds
jim
Click to expand...
Click to collapse
Hi All,
I was stuck at the Serial for a Looooooong time. Nothing worked. Until I did the following:
1) Using HHDHexeditor, copy the first 416byte (NOT 220byte!)
2) Write the copied original backup ROM into the new ROM (.nb1 file)
3) Put into your 02 Mini
4) VERY IMPORTANT! - Plug into your USB PORT!
5) Then I see the "Press Power button to Flash!"
and I am happily flashing my device now ... My guess is that it needs to be on external power in order to upgrade .... Thanks everyone .. can't wait to see my new baby with 27Mb storage! :twisted:
I'm using 256Mb SD Card ....
Alvin
How can i know the backup file name stored in the memory card? (*.nb1)
Thx~~
i am not seeing the popup window in which to select "d2s"...can anyone help?
update: Ok, so i was just temporarily blind! Have managed to continue and have fingers crossed it is ok.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your ppc.
After this.... how I do the soft reset with my ppc?? Connect or diconnect with the USB?? Coz I can't turn it back to the normal from boot loader mode even I do soft or hard reset after the rom flashing.......why?? :shock:
cojones said:
update: Have managed to continue and have fingers crossed it is ok.
Click to expand...
Click to collapse
I get the message ROM size isn't enough when i press the power button to flash from the sd card...why is this?
Talents said:
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
Click to expand...
Click to collapse
WTF ??? The only options are COM1 COM2 or COM3 and the Baud rate.
What a POS!
Hey guys,
Well I succeeded in upgrading to Anansky's BigStorage ROM and was very satisfied, but now my stupid speaker broke (I have a similar problem to other users where they can hear sound if they blow into the speaker). I have to return the Magician so I need to revert back. Can someone PLEASE upload the original XDA II ROM PLEASE???
Here's a list of instructions on how to backup the ROM:
Backing up your ROM can be done by connecting your Magician to the PC through the data cable when you first uncheck the USB connection of active sync.
If your Magician connects with active sync because you didn't uncheck the USB connection in the active sync connection settings then you will not be able to backup your ROM to an SD memory card.
1. Before connecting your Magician you should bring it into the boot loader mode. This can be done by simultaneously pressing power + camera buttons and at the same time the soft reset button with the stylus.
2. After connecting your Magician to the PC through the USB in boot loader mode and having your SD card inserted into the MDA, you run romupdate.exe.
3. Then choose the USB connection in the connection settings of romupdate.exe window and click on ok. After that a terminal window will popup in that window.
4. Type d2s and press enter. Your Magician will start copying the ROM to the sd card. The screen of your Magician will be dark (no light), but you will see it counting up to 100%. When it reaches 100% it will say it is calculating the checksum. Give it some time till its done and it will say checksum ok.
5. After finishing the transfer of the ROM from your Magician to the SD card, put your SD card into an SD card reader connected to your pc. Your pc might pop up a warning message that says your SD Card is not formatted would you like to format? Click No and open a Command prompt (DOS) window.
6. Change directory to your root directory (cd c:\) and run the command ntrw read o2orig.nb1 x: where x is the drive letter of your sd card. That command will create the ROM Backup file of your ROM into your C drive root directory by the name of o2orig.nb1. Make sure you keep o2orig.nb1 in a safe place and use a copy of that file for the rest of the procedure. Note that after finishing the copy from your SD card to o2orig.nb1 file ntrw might give you an error, just don’t pay attention to it.
7. WinRAR the o2orig.nb1 file, then upload it to the XDA Developers FTP .[/i]
No one wants to help?
The question is why havent you got a backup?? You were told to do this in the first instance should anything go wrong!!
somebody apparently has uploaded the O2 mini original rom, check it out!
The answer to this was I was using my digital camera as an SD reader...and the backup didn't work properly for some reason. So now I have nothing.
The backup (I think you're talking about the O2 Original Dump Rom) doesn't work for me. I have a 1.11 version of the O2 Asia ROM, but I'd rather have the original WWE. Oh yes, and I've tried several times with the "Original Dump Rom" using 220, 415 and 416 bytes...nothing works.
This may work for you - use the romupdate software to get the rom image of your device to the sd card. By this stage you have an edited rom image on the pc. Use ntrw to write that image over the top of the sd card that you have just written to with romupdate. Then plug it into the ppc. Do not format the sd card in the immediate procedure at anytime. For whatever reason I think the romupdate software puts a format on the sd card which the ppc recognises. There were a number of errors on the ppc screen just after installation however when you push the reset button hey hey the original splash screen boots up. Prior to this check that the edited rom header is 416, in my efforts it was not 415. The RomMiniOrg.nb1 image was good with the only NON change being the radio which remained at version 1.11 but I downgraded it to 1.05. I don't think the service centre will worry to much about this should you need it. Goodluck with this, it worked for me.
Hi yozhek,
Thanks for the help. I did what you said but it still didn't work. However, I used O2_mini_asia from the FTP to downgrade my extended rom, protocol and rom version...then I found the Radio downgrade on the FTP and downgraded to version 1.01.
now everything is original!
I didn't know that the Nb1 files did not include the radio stack downgrade so I had to downgrade that seperately.
the command in the romupdate program basically determine which image to backup.
d2s for rom, but I am not sure what's the other command for extended rom and radio. Anybody?
Can I use MaUpgradeUt_noID.exe to change the ROM on my mini with the o2mini_asia.nb1 ?
miniuser: no
you will have to use the process as described in procedure.doc (available in the FTP under anansky's bigstorage folder)
I did as described in the procedure.doc. I have run this command
ntrw write o2mini_asia.nb1 e: and then inserted the SD card into my mini and pressed the power+camera+soft reset button
but it is not doing anything, it has stopped at "Serial" above and v1.00 below for an hour now. Any suggestions?
cheers
mini_user
I tried it second time, now it says
SD DOWNLOAD
==========
SECTIONS=1
Not Allow Update
Any Suggestions?
Cheers
Sorry for the last post, was trying out something else.
I am using a 256MB SD card and the size of the rom is only 127MB after ntrw, does it make any diff??
you can always ntrw write a 127mb rom image into a 256mb sd card.
the rom flash will not work (and hence the no update allowed message) if your rom image in your sd card is invalid for some reason. I make a bobo previously, trying to copy 416byte of anasky rom into my original rom, instead of the other way round. And it give me that error message. After realising my mistake, and did the right modification, the flash went through successfully. so double check your rom header edit if you are not able to proceed to the flash step.
I have a mini with qteck 1.11.00 WWE
and I have download the o2mini rom from xda ftp and have got a 256 mb card
if I want to flash my mini with the o2mini rom the are these the steps to follow
1. dump qtek rom into card
2. copy it to pc
3. copy 1st 416 bytes of qtck into o2mini rom
4. dump o2mini rom into card
5. put mini into bootloader mode
6 update with mini rom
cheers
zenkinz said:
somebody apparently has uploaded the O2 mini original rom, check it out!
Click to expand...
Click to collapse
where is the file?
Hello All,
I follow the upgrade guide, when doing the step "8. Downloading your New ROM onto your Magician", I press the Power, Camera and Reset buttons at the same time to go to "Boot-loaded" mode. But the screen DOES NOT show "SD Download", it still show "Serial".
Please help!!
I am using O2 mini limited edition.
Thanks,
Jack
Jack,
Try putting your SD in your PC card-reader again, when it doesn't want to format it the writing of the rom with ntrw has failed in such a way that a mbr is still present on your sd. Is it the same card as you used for dumping your own rom? Did you dump at all?
To solve your problem
- stay in bootloader
- connnect usb (now your magician reads USB)
- dump your own rom on the SD, this will destroy the mbr & now ntrw will write the rom-image at the beginning of the Sd & your magician will see it.
- make a back-up from your SD with ntrw if you like
- write back the image, you have from your previous attempt, with ntrw
- put the SD in your magician, still in bootloader
- now it should read 'press power to flash'
Good luck, M
jack98lau said:
Hello All,
I follow the upgrade guide, when doing the step "8. Downloading your New ROM onto your Magician", I press the Power, Camera and Reset buttons at the same time to go to "Boot-loaded" mode. But the screen DOES NOT show "SD Download", it still show "Serial".
Please help!!
I am using O2 mini limited edition.
Thanks,
Jack
Click to expand...
Click to collapse
You have to HOLD the three buttons until you see the screen that says to hit the power screen to update. If you don't get that screen, load the .nb1 file back onto the SD card again.
I had to hold the three buttons for several seconds.
Hello,
Thanks for your reply!
But I encouter any other problem. After following the procedure, the SD download screen was shown it shows 100% and everything run smooth. Then I hard reset my o2 mini. After that the memory still not change (64MB + 64MB). I am using the file mksBigStorage112.nb1.
Does anyone know what is the problem ?
Thanks,
Jack
Jack,
The device only has 64Mb. Take a look at the storage folder, this should be around 27Mb. Start -> Settings -> system -> Memory -> second tab & select Storage.
Cheers, M
oh, ic. But still has around 7mb.
Are you sure that you didn't flash your own dump back, cause this is not the expected result.
Try again pls etc etc & more of these predictable phrases.
Regards, M
jack98lau said:
oh, ic. But still has around 7mb.
Click to expand...
Click to collapse
You updated your ROM to a new version, but not a BIG STORAGE version.
To get more storage, you have to flash with a BigStorage ROM. There are several threads here describing the process in detail. Do a search on "Big Storage Explained" or such and you will get detailed instructions.
mksBigStorage112.nb1
Sounds like a BS to me.
Hello Everyone,
For quiet some time now I've been trying to get root on my German G1 on RC9.
I've been trying to follow the guides that are on this forum, but everything on here is so scattered D:
Right now I'm having difficulties while trying to downgrade to RC7.
What I've done so far:
Get the SD Cards Serial.
Reverse it.
Zero the first two digits.
Make a goldcard image.
I then formatted the SD Card and copied the RC7 DREAIMG.NBH onto it.
After that, I went into linux to dd the goldcard on the card aswell.
Now...After I try to access the bootloader, it will Load the Image, Check the Image, and then give me the usual "not allow" error.
What am I doing wrong?
Any help is greatly appreciated.
Anyone able to help me out?
How exactly did you make the goldcard.img? Did you use qmat or the online generator? I don't think that you need to reverse or zero anything for the online tool...
PM me if you need further assistance in creating the goldcard.
Yes you need to reverse the serial and zero the first byte.
@Bavilo
We need more details to help you. So post everything you did so far. (CID, commands you used to format and to flash the img, ...)
Thanks for the responses!
Here's a little more info.
CID: 03534453553032478021452741008b8a
(could someone generate a correct goldcard.img for me?)
I formatted the card in windows. Fat32, 4096 allocation size.
I wasn't sure on the dd part, but this is what I used:
dd if=goldcard.img of=/dev/sdd
that gave me the correct response. Although the card is called sdc1. Maybe that was the problem?
Also I do not have a usb card reader, so the card is still plugged into the G1 while I'm doing all this. Will that make it not work?
Thanks in Advance
Finally I got it!
I used the wrong node for the sd card. It was sdc....not sdd...<_<
I will be performing the downgrade now. I'll report back if there are any further problems. Stay tuned ^^
Not good D:
"Update Terminate
UPDATE FAIL"
now what...
Edit:
The SD card now seems to be dead...I can no longer format it. So I'll have to get a new one first and then attempt to update my G1 again...sighhhh
The sd card shouldnt die that easily. Try to put the card in your computer and open gparted on linux. You should see the card in the list.
If it doesnt show reinsert your card and post the output of "lsusb" and "dmesg |tail -30".
If you want i can help you in german. My jabber name is k[email protected].
Hmmm...
I'm there now too... I have a german G1 RC9 and struggle to downgrade it.
I used the 2GB card of the phone
Online generated the Goldcard.img
DD't it to the sde (thats the correct one) using a card reader
copied the DREAIMG.nbh (maybe capitalisation?) on the sd
reboot -> not allowed and a red number ->Bootloader ->nothing
Did I miss anything? maybe first copy and the dd? I thought I tried it.. but hard to remember at 2am and fixing the filesystem 'cause I dd't to sda Grrrrr
Ok I managed to root my phone now!
Turns out that the slot for the mircosd card on my card reader was busted...<_<
Also the reason the Update Failed in the first place, was because I copied the extracted DREAIMG.NBH file onto the sdcard using ubuntu. Which must have corrupted it.
The way that made it work was to go into windows, move the RC7.zip onto the sdcard, and extract it on the sdcard. The update passed the first time
Thanks to everyone who has helped me!
Hmmm...
I'm there now too... I have a german G1 RC9 and struggle to downgrade it.
I used the 2GB card of the phone
Online generated the Goldcard.img
DD't it to the sde (thats the correct one) using a card reader
copied the DREAIMG.nbh (maybe capitalisation?) on the sd
reboot -> not allowed and a red number ->Bootloader ->nothing
Did I miss anything? maybe first copy and the dd? I thought I tried it.. but hard to remember at 2am and fixing the filesystem 'cause I dd't to sda Grrrrr
Click to expand...
Click to collapse
Using linux do a "dmesg" and check the node name of your sd card. Make sure you dded the goldcard onto the right sdcard. If you still get the "not allow" error, then you're goldcard is at fault. Maybe you didn't type the correct cid?
I finally managed it:
The mistake was:
Most howtos say, after reversing the CID you should add 00 at the beginning and use this to make the goldcard.
WRONG! I just used the reversed String and this finally made it possible.
Hope this helps
can someone genrate me please a correct goldcard?
CID: 1c5356555344202010051c4cd7008c4a
i cant manage to do it.
please help.
thanks.
HOW TO PARTION WITH PARAGON PARTITION MANAGER
**** YOU WILL LOSE ANY INFO ON THE SDCARD - PLEASE BACK UP IMPORTANT INFO PRIOR TO STARTING THIS PROCESS ***
**** these are instructions for Windows XP ***
***** if you are using Windows Vista - You need to change the permissions to Administrative in order for this to work - RIGHT CLICK ON THE START BUTTON AND GO TO ADMIN SETTINGS - even if you are the only user of the PC
have the sdcard in the card reader or in the phone mounted to the pc !!!!
OPEN PARTITION MANAGER...
CLICK ON PARTITION MANAGER IN THE LOWER RIGHT HAND CORNER..
then click on the line that represents the sdcard, and right click on it, and choose format partition.. name the volume label - fat32
then click format..
computer might hang for a minute or 2, and then a popup will come up and say click GREEN CHECK to apply changes..
click the GREEN CHECK IN THE TOOLBAR AREA..
you will then see another pop up show - apply changes, choose yes, then you will see OVERALL PROGRESS AND GEARS TURNING.. LET IT PROCESS AND TAKE ITS TIME.. DONT HIT CANCEL..
when its done the cancel button at the bottom will change to Close.. click it..
AND THE FIRST STAGE IS DONE...
NOW ITS TIME TO CREATE THE EXT2 PARTITION..
Now on the Left side of the screen click Create partition.. and a screen will now show Create New Partition Wizard... it lets you chose which drive to partition ( make sure you chose the sdcard - it will be the one with the smallest volume/size of the sdcard in gbs.. should be on the bottom )...
HIT NEXT
now a slider will appear where it says new volume....
move the slider with the mouse, and make it how big you want it.. for ext2 partiiton about 500mb to 1gb is plenty... 500mb is good size.. ( size wont be exact so get it close to the size you want..
WHEN DONE CLICK NEXT...
NOW IT GIVES YOU THE OPTION TO FORMAT THE PARTITION...
CLICK THE PARTITION TYPE DROPDOWN MENU AND CHOSE LINUX EXT2... AND GIVE IT A VOLUME LABEL OF ext2.
then click next...
PC WILL PROCESS AND HOURGLASS WILL SHOW WHERE THE MOUSE POINTER IS.. AND THEN A POP UP WILL SHOW - SAYING -
COMPLETING THE CREATE NEW PARTTITION WIZARD..
CLICK FINISH...
THEN IT TAKES YOU BACK TO THE SCREEN SHOWING THE DRIVES, AND WHAT YOU CREATED, AND THE OPTION AT THE TOP WILL SAY - APPLY ... choose apply
THEN IT WILL ASK YOU TO - APPLY PENDING CHANGES AGAIN, choose yes..
NOW YOU WILL SEE THE GEARS WORKING AGAIN.. LET IT RUN TILL IT SAYS complete..
*it will take a few minutes to process.. let it run...
you might get a pop up for the sdcard drive as a open folder on the pc just showing that its done, just go back to paragon and let it finish running...
once complete you will get a pop up saying SYSTEM RESTART IS REQUIRED TO COMPLETE OPERATION.. CHOSE RESTART THE COMPUTER...
You will see a paragon manager screen, that will hang for a almost a minute, and then the bar will fill saying 100 percent complete, press any key to reboot the pc..
AS LONG AS THERE IS NO ERRORS, YOUR DONE..
FORMAT COMPLETE..
PARAGON WILL START UP ON ITS OWN, AND SHOW THE PARTITIONS AS BEING COMPLETE..
----
*****edit
Originally Posted by Androidandy
check that the ext2 partition is good by typing busybox df -h in terminal.
************************************************************EDIT *****************
If your having issues using paragon partition manager, and trying to make a linux swap partition, try these instructions for formating thru Cyanogens newest recovery
Formatting you SDcard
You only need to do this once folks..if you already have 3 partitions including linux-swap move to step 2
You need Recovery image 1.31 to do this folks!
To format card SD card with linux-swap WARNING!!! this will reformat you entire SD card!!
You can use the recovery console and parted to format SDcards with 1.31 folks, no more going through hassles you have the tools on you G1!...here is an example of how to do this in recovery console using parted
Example for 8GB card (specific value's may be slightly different use print to verify your total SDcard size~!
Reboot and enter recovery
Enter console
#parted /dev/block/mmcblk0
#print (to verfiy we know what size card we are dealing with, the details should be straight forward)
rm 1
rm 2
mkpartfs primary fat32 0 7584
mkpartfs primary ext2 7584 8127
mkpartfs primary linux-swap 8127 8159
#print (to verify we have the 3 partitions)
Example for my 4GB card
#parted /dev/block/mmcblk0
#print (to verfiy we know what size card we are dealing with, the details should be straight forward * then grab a calculator to figure the exact amounts... as shown below that is an example..)
rm 1
rm 2
mkpartfs primary fat32 0 3420
mkpartfs primary ext2 3420 3932
mkpartfs primary linux-swap 3932-3964
"End?" you need to place the last value for the linux swap eg.3964 for my 4GB card
#print (to verify we have the 3 partitions)
Next we need to "quit" parted and upgrade our ext2 partition to ext3
#upgrade_fs
Swap value is set to 30 currently, you can change this by modifying the "echo" value for swappiness in the a2sd.sh script
swap partition shouldnt be no larger than 92mb
ext2/3 partition shouldnt be more than 500mb ( more than that is too much )
( directions from a post by justanothercrowd )
Thank You, for a great post but, can you please fix this link *** word docx with screenshots - http://kaysesoze.wordpress.com/wp-ad...ttachment_id=4
When I signed in I received the following message "You are not allowed to edit this attachment." Again THANK YOU,
V/R
Biz
stuck
I installed paragon parttition manager 9 pro trial version after installtion I reboot and , it brought me to the blu paragon advance recovery screen...I notice I forgot to back up my sd card...but it won't let me out of this screen...tried rebooting it still brought me back to this screen...is there any solution for this problem....its gotta be something easy...I just don't know what to do to get back to my desktop.....HELP!!!!!!!!!PLEASE!!!
biz18434 said:
Thank You, for a great post but, can you please fix this link *** word docx with screenshots - http://kaysesoze.wordpress.com/wp-ad...ttachment_id=4
When I signed in I received the following message "You are not allowed to edit this attachment." Again THANK YOU,
V/R
Biz
Click to expand...
Click to collapse
thanks for bringing that to my attention.. will try and fix it..
toconfuze1 said:
I installed paragon parttition manager 9 pro trial version after installtion I reboot and , it brought me to the blu paragon advance recovery screen...I notice I forgot to back up my sd card...but it won't let me out of this screen...tried rebooting it still brought me back to this screen...is there any solution for this problem....its gotta be something easy...I just don't know what to do to get back to my desktop.....HELP!!!!!!!!!PLEASE!!!
Click to expand...
Click to collapse
during the paragon process it says do not interrupt it while it is formating, cause you pc can become unstable. and thats exactly what you did.. u might be able to press the esc button, i believe it gives that option at the bottom of the screen to exit it properly. but rebooting was wrong...
anytime u FORMAT any drive or card you will lose information, thats pc fundamentals... will add the issue about losing info to orig post..
was stuck
thanks a lot....fixed
Help
I know I am always running into problems. But i am freakin out about this and i don't know if this is the right thread to be posting this or maybe someone can lead me to other thread with this fix.
Question
First i partitioned my mini sd card using my G1 with paragon manager and when everything was done the computer restarts.
But the weired thing is that now when i mount my G1. My G1 is recognized by my computer but it does not show me the storage device on my computer folder or even prompt me with opening a folder for my storoge card. I am freakin out.
Things i tried.
1. Rebooted my phone
2. nandrroid backup restore
3. restarted my computer
4. changed minisd cards.
5. uninstalling the usb android driver and reapplying it
6. went to usb debug on the settings on the phone
nothing worked.
Thanks . Any help would do.
------------------------
Fix ******Update
It took me alot of time to figure this out. if anyone gets this problem just assign your sdcard a Letter. Example: E: Drive.
When i look at these tutorials it does not mention anything like that.
thanks anyways
stonefurry said:
I know I am always running into problems. But i am freakin out about this and i don't know if this is the right thread to be posting this or maybe someone can lead me to other thread with this fix.
Question
First i partitioned my mini sd card using my G1 with paragon manager and when everything was done the computer restarts.
But the weired thing is that now when i mount my G1. My G1 is recognized by my computer but it does not show me the storage device on my computer folder or even prompt me with opening a folder for my storoge card. I am freakin out.
Things i tried.
1. Rebooted my phone
2. nandrroid backup restore
3. restarted my computer
4. changed minisd cards.
5. uninstalling the usb android driver and reapplying it
6. went to usb debug on the settings on the phone
nothing worked.
Thanks . Any help would do.
Click to expand...
Click to collapse
1. did you do the fat32 first, then ext2 second ?
2. did you mount the sdcard to the pc ?
3. may show as F drive on your pc !!!
I used PM 10, it is very easy. However when the program wants to reboot it says there is an error, but I check that the ext2 partition is good by typing busybox df -h in terminal.
I've partitioned several cards now and they all work.
I found that doing a wipe then installing Lucid's rom.
I reinstall my applications from mybackup pro and downloading others from the market.
I test everything is working fine, then and only then I use the scripts that Lucid posted.
To recap ensure that busybox recognises the ext2 partition then wipe, install Lucids rom
Androidandy said:
I used PM 10, it is very easy. However when the program wants to reboot it says there is an error, but I check that the ext2 partition is good by typing busybox df -h in terminal.
I've partitioned several cards now and they all work.
I found that doing a wipe then installing Lucid's rom.
I reinstall my applications from mybackup pro and downloading others from the market.
I test everything is working fine, then and only then I use the scripts that Lucid posted.
To recap ensure that busybox recognises the ext2 partition then wipe, install Lucids rom
Click to expand...
Click to collapse
thank you for the info..
was looking for the commands to verify that the ext2 partition is done correctly, and of course it verifies that busybox is working also..
I'm having a large issue with my new Micro SD card.
When using PM and my MicroSD in an SD adapter it allows me to format and create partitions successfully JUST FINE with my Sandisk 2gb which is probably a class 2 or just not a class at all...it doesn't say on the card at all.
BUT I just bought a Transcend 8gb Class 6 HC card and when using the SD adapter the computer recognizes it just fine to open and view files...BUT Paragon says its "Invalid" and won't allow me to format, partition, or anything.
I have no idea what needs to be done differently. It works just fine in the phone and moving files but Paragon won't recognize it or allow it to be modified.
I need some help please!!!
First of I'm new to all this so I'm a nood and I need some help massively I have trying to make this ext2 partition on ubumtu for months and always get an error message and a lost and found folder in the ext2 partition. Found these directions and finally make the partition w/ no error messages. Fat32 1st then ext2 2nd type busybox command so I think its done right. So I try to mkdir /system/sd/app for marcus directions on apps to sd to use his apps to sd2 app and I get error /system/sd/app read only. Why is that so? I look in pargan partitioner were I made the parition and there both still there. I would be greatfull if anyone can help out a nood like me [email protected]. I have been trying to get this ext2 partiton for months and today thought I did it correct cause no error messages and boy was I wrong!! Please anyone help !!
Bronze G1 W/ JF 1.5 cupcake W/Areo
NO APPS TO SD1! HELP PLEASE
Saphire SLP
[email protected]
i like this tuturial, but one problem, doesnt work with vista 64bit -.-
im literally crying
So every time I try to format, my phone unmounts my damn card.
Any ideas?
worked for me on vista 64
missxoash said:
So every time I try to format, my phone unmounts my damn card.
Any ideas?
Click to expand...
Click to collapse
Using Paragon or windows?
missxoash said:
So every time I try to format, my phone unmounts my damn card.
Any ideas?
Click to expand...
Click to collapse
im have the same problems as her, i dunno why
I am running vista 64 and paragon profesional. I can get it to format and can get the ext2, but I can not do anything with the card. I try and reformat the fat32 and give it a letter for a drive but it wont take or if i format it and then create the ext2 it gives the ext the drive letter(both cannot have a drive) What gives and in the meantime I have to use the 1gig because although paragon recognizes the sd card my pc does not!
so i've done everything in the tutorial. and even the coding for checking busybox.
it doesnt show the ext2.
and i tried running the lucid commands
and it says ext2 is not mounted.
i get all the way to the ext2 part the very last thing
like mount/dismount and i get a error
saying to close a program or restart pc
cant close program because i dont know what it is so i click retry same error
i restarted pc 2 times
still same thign tried reformatting all over again what am i doing wrong? thanks guys!
pr0cl1v1ty said:
i get all the way to the ext2 part the very last thing
like mount/dismount and i get a error
saying to close a program or restart pc
cant close program because i dont know what it is so i click retry same error
i restarted pc 2 times
still same thign tried reformatting all over again what am i doing wrong? thanks guys!
Click to expand...
Click to collapse
are u using a sdcard reader ??