Okay so my note 10.1 gt-n8000 is bricked , So i went and research a while and found that if i install stock rom then it will go as default .
So I downloaded the stock rom and installed it via odin and it was successful but when I try to go to recovery the same cwm recovery appears ?Im like wtf and installed stock rom again and again like 4 times but still cwm was not removed and the thing here is that im stuck on bootloop.
CWM Recovery starts with
E: cant open /cache/recovery/log
e: cant open /cache/recovery/log
e: cant open /cache/recovery/last_log
e: cant open /cache/recovery/last_log
and it cant mount sdcard either
How can I fix this bootloop ? I think it has something to do with cwm recovery because everytime i go and factory reset It restarts itself .
I'm in big trouble.
ODIN LOG:
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> tz.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
<ID:0/004> Removed!!
so u cant access recovery mode, only download mode is accessible ?
---------- Post added at 06:46 PM ---------- Previous post was at 06:41 PM ----------
you need to get the right Pit file
and Check "NAND Erase All" in Odin while flashing the stock rom
It will erase everything in your phone including corrupted recovery files
scorpiohyena said:
so u cant access recovery mode, only download mode is accessible ?
---------- Post added at 06:46 PM ---------- Previous post was at 06:41 PM ----------
you need to get the right Pit file
and Check "NAND Erase All" in Odin while flashing the stock rom
It will erase everything in your phone including corrupted recovery files
Click to expand...
Click to collapse
I cant file pit file... Searched all over :/ Do you have N8000? Could you share pit file?
I have a worst problem, it began after i upgraded to kitkat, but works for few months, and USB is not debugging enabled, by mistake...
Until i forgets it on the power fro four hours, then i discovered that it is rebooted and rebooted and rebooted and stuck on the samsung icon, i took it for samsung to fix it they told it is motherboard, and has a price more than the device itself, so i took it from them, and tried to start it, it is failed to start after... i removed the cover and removed the battery for a minute, useless, i couldn't turn it again, i did all the things on the internet, useless.
The PC is not detecting the device.
The device is not starting on.
the battery is removed many times, and plugged again.
Even i tried to charge the battery using its poles by a direct charger on it, while it is un-plugged from the motherboard.
The device can't be start or give any power on the screen...
Kindly help... Thanks in advance.
Related
I have a soft bricked S3 thats really stumped me. Its hanging at the verizon boot video so i figured i would just ODIN back to stock and be done with it. Everytime i try to flash VRALEC.bootchain.tar.md5 i fail. I tried to flash stock.vzw_root66 and i fail. I tried to flash COMBINATION_I535VRBLK3_I535VZWBLK3_381038_REV09_user_low_ship.tar.md5 and i fail. Ive tried different cables and different USB ports but i cant get odin to flash anything. Please help lol. I am using a NON rooted device.
heyitsdan03 said:
I have a soft bricked S3 thats really stumped me. Its hanging at the verizon boot video so i figured i would just ODIN back to stock and be done with it. Everytime i try to flash VRALEC.bootchain.tar.md5 i fail. I tried to flash stock.vzw_root66 and i fail. I tried to flash COMBINATION_I535VRBLK3_I535VZWBLK3_381038_REV09_user_low_ship.tar.md5 and i fail. Ive tried different cables and different USB ports but i cant get odin to flash anything. Please help lol. I am using a NON rooted device.
Click to expand...
Click to collapse
Are you putting the .tar file in the PDA slot in Odin?
Is your phone in download mode?
What base was you phone when it was working? ICS or JB?
If ICS stick with flashing root66 ICS for now (not any bootchains or modems) so that we can focus of getting your phone working first before any type of upgrade.
Also, if you cannot restore your phone by simply flashing root66 in Odin, follow this guide HOW-TO Unbrick Your Soft-Bricked Galaxy S III
corbn89 said:
Are you putting the .tar file in the PDA slot in Odin?
Is your phone in download mode?
What base was you phone when it was working? ICS or JB?
If ICS stick with flashing root66 ICS for now (not any bootchains or modems) so that we can focus of getting your phone working first before any type of upgrade.
Also, if you cannot restore your phone by simply flashing root66 in Odin, follow this guide HOW-TO Unbrick Your Soft-Bricked Galaxy S III
Click to expand...
Click to collapse
I am a base ICS and yes i have the phone in download mode, and i am using the pda slot but i cant get anything at all to flash sucessfully. That is the guide that i got the files from and i cant even get the first file to flash....
1.Open up ODIN
2.Select only the following box: F. Reset Time
3.Flash the VRALEC bootchain in the PDA section and wait for a PASS message
Thats where i get a fail message
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
heyitsdan03 said:
I am a base ICS and yes i have the phone in download mode, and i am using the pda slot but i cant get anything at all to flash sucessfully. That is the guide that i got the files from and i cant even get the first file to flash....
1.Open up ODIN
2.Select only the following box: F. Reset Time
3.Flash the VRALEC bootchain in the PDA section and wait for a PASS message
Thats where i get a fail message
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Did you check your MD5's? Also, just confirming that you already tried to restore by flashing root66 .tar in PDA with only Auto Reboot and F. Reset checked off? Also, read the second post in that guide and see if your symptoms are similar to the guide's second brick scenario.
corbn89 said:
Did you check your MD5's? Also, just confirming that you already tried to restore by flashing root66 .tar in PDA with only Auto Reboot and F. Reset checked off? Also, read the second post in that guide and see if your symptoms are similar to the guide's second brick scenario.
Click to expand...
Click to collapse
Yes i tried to flash just the root66 and this is what i get:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (WP)
<OSM> All threads completed. (succeed 0 / failed 1)
And i also tried the other guys post and this is what i get there:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (WP)
<OSM> All threads completed. (succeed 0 / failed 1)
What were you doing when it hung at the Verizon splash screen(what caused the brick)?
letinsh said:
What were you doing when it hung at the Verizon splash screen(what caused the brick)?
Click to expand...
Click to collapse
This is a friend of mines phone and from what i understand she was doing the jellybean update and it lost power in the middle of it
heyitsdan03 said:
This is a friend of mines phone and from what i understand she was doing the jellybean update and it lost power in the middle of it
Click to expand...
Click to collapse
Have you tried resetting the phone via the stock recovery?
corbn89 said:
Have you tried resetting the phone via the stock recovery?
Click to expand...
Click to collapse
stock recovery wont boot
you're using Odin v3.07?
---------- Post added at 03:45 PM ---------- Previous post was at 03:40 PM ----------
wait.
Stock recovery won't load, but you can get into download mode?
letinsh said:
you're using Odin v3.07?
---------- Post added at 03:45 PM ---------- Previous post was at 03:40 PM ----------
wait.
Stock recovery won't load, but you can get into download mode?
Click to expand...
Click to collapse
Yes, recovery wont boot but i can get into download mode, and i am using odin 3.07
Maybe this will help, i tried for the hell of it to boot normal and now it will go past the splash screen and come up to an "encryption failed" error with a reset button. The reset button does nothing..
have you tried getting into recover since the Odin flash failed?
Also, do you have Kies running on your computer? When using Odin, kies needs to be disabled.
---------- Post added at 04:14 PM ---------- Previous post was at 04:05 PM ----------
A little different approach.
this thread: http://forum.xda-developers.com/showthread.php?t=1974114
Try the VRBLK3 files (official vzw jb).
Yes i just tried again and nothing... and no i dont have kies even installed
letinsh said:
have you tried getting into recover since the Odin flash failed?
Also, do you have Kies running on your computer? When using Odin, kies needs to be disabled.
---------- Post added at 04:14 PM ---------- Previous post was at 04:05 PM ----------
A little different approach.
this thread: http://forum.xda-developers.com/showthread.php?t=1974114
Try the VRBLK3 files (official vzw jb).
Click to expand...
Click to collapse
This is what i get when i flash VRBLK3
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
heyitsdan03 said:
This is what i get when i flash VRBLK3
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
That's the file you mentioned in the OP or the one I just pointed you to (different files)?
That last one was the file you pointed to me and yes they were different files, neither one work.
Flash this (stock bootchain) in PDA: http://truelinux.net/sch-i535/bootchains/BOOTLOADER_I535VRALF2_618049_REV09_user_low_ship.tar.md5
then download this (stock rom), unzip it, and flash in PDA:
http://goo.im/devs/invisiblek/i535/...535VZWALG1_743127_REV09_user_low_ship.tar.zip
Having so many files fail with an Odin flash makes me think the error is caused by something else, though...
What else could it be?
Sent from my SAMSUNG-SGH-I747 using xda premium
Honestly, we've reached the limit of my experience. Must issues with Odin result from the physical connection. I know you tried different cords and different ports. I assume you're doing this, but make sure your usb cable is plugged into a port on the motherboard, not a hub or remote port.
I honestly don't know what the next step is... Reinstall drivers and Odin?
Sent from my SCH-I535 using xda app-developers app
Thanks to Atntpt that opened my mind. I've unpacked .Tar odin package of 5.1.1 and flashed something like modem,boot and recovery (adding .tar in the file names before flash them) one per time, then a custom kernel and last twrp, and the phone stops to reboot. Samsung Switch done the rest of the work. Hi guys, please help me, i'm working no stop on my phone from yesterday without a solution. Yesterday i've tryed to flash mm(Coming from noblerom installed without tripping knox with modified bootloader of 5.0) from the post in general. Flash of mm has fail with an error of a bootloader. then i've tryed to flash latest stock rom(not of my country), and gave me an error in flashing hidden.img, i've tryed to flash in odin, seems fine and phone boots but have no charge. attacched to charger the phone boots and shut down after 5 seconds.
Both recovery and download mode, works
in official recovery and twrp can't mount system
in official says
failed to mount '/system (invalid argument
If you know something about, please help me.
Log of odin flash
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
after hidden fails flash custom kernel via odin.. i should boot normaly..(will tip KNOX!!) that was the reason i tiped knok was unable to bypass that situation
Atntpt said:
after hidden fails flash custom kernel via odin.. i should boot normaly..(will tip KNOX!!) that was the reason i tiped knok was unable to bypass that situation
Click to expand...
Click to collapse
can you send me a link?
I'm glad I could help
Hello guys
i really need help to unbrick this phone, ive tried to root the phone and its bricked now !
not working at all
boot looping
cant enter recovery
i tried to flash twrp recovery using odin
but couldnt enter it to
tried to flash a whole rom using odin and i get an error
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1005)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> SingleDownload.
<ID:0/009> sboot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> FAIL!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and in the download mode i get
KNOX WARRANTY VOID:1 (0X0301)
AP SERV: B:3 K:2 S:2
please help me guys to make it boot
i cant do anything but see this blue screen
any help ?
Im getting out of my mind
Is it even fixable ??
Please please help me guys
Its fixable, but you'll need to trip your Knox , I was in ur shoes and here's how I got it fixed
Flash Philz recovery from Odin on download mode, then boot into recovery (home+power+volume up) then reset everything I mean everything except recovery, then go back into download mode and flash stock firmware Knox will be tripped cuz of Philz
Hope it works out
Edit: just realized your Knox was already tripped lol
---------- Post added at 04:59 AM ---------- Previous post was at 04:50 AM ----------
If your wondering where to download philz, go to Arter97s website http://arter97.com/browse/exynos7420/recovery/11.0/
Find model number (G920I for me) then download the recovery
SwaggerDaddy said:
Its fixable, but you'll need to trip your Knox , I was in ur shoes and here's how I got it fixed
Flash Philz recovery from Odin on download mode, then boot into recovery (home+power+volume up) then reset everything I mean everything except recovery, then go back into download mode and flash stock firmware Knox will be tripped cuz of Philz
Hope it works out
Edit: just realized your Knox was already tripped lol
---------- Post added at 04:59 AM ---------- Previous post was at 04:50 AM ----------
If your wondering where to download philz, go to Arter97s website http://arter97.com/browse/exynos7420/recovery/11.0/
Find model number (G920I for me) then download the recovery
Click to expand...
Click to collapse
i flashed it but i cant boot to recovery
it says recovery is not seandroid
ughhh it seems so hard to fix
Are you sure that you tried to get in recovery. For me it seems that your error comes on boot up
http://www.droidviews.com/fix-recovery-is-not-seandroid-enforcing-error-on-samsung-galaxy-devices/
http://www.galaxys6edgeupdate.com/r...nforcing-galaxy-s6-t-mobile-g920t-how-to-fix/
alawii_shark said:
i flashed it but i cant boot to recovery
it says recovery is not seandroid
ughhh it seems so hard to fix
Click to expand...
Click to collapse
this can be fixed, go to sammobile find the firmware according to your phone model, flash it using ODIN, that's it.
Hi @alawii_shark
Can you share if you are on 5.0.2 or 5.1.1 firmware, bootloader & modem?
- Renolz
alawii_shark said:
i flashed it but i cant boot to recovery
it says recovery is not seandroid
ughhh it seems so hard to fix
Click to expand...
Click to collapse
LOL are you sure you let the phone go to recoverymode ?
Hold volume up + home + power for 6 sec you will het inside recovery
Have you entered into recovery mode ?
alawii_shark said:
Hello guys
i really need help to unbrick this phone, ive tried to root the phone and its bricked now !
not working at all
boot looping
cant enter recovery
i tried to flash twrp recovery using odin
but couldnt enter it to
tried to flash a whole rom using odin and i get an error
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1005)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> SingleDownload.
<ID:0/009> sboot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> FAIL!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and in the download mode i get
KNOX WARRANTY VOID:1 (0X0301)
AP SERV: B:3 K:2 S:2
please help me guys to make it boot
i cant do anything but see this blue screen
Click to expand...
Click to collapse
How many times has been said .... Sboot fail is when you try to flash an older firmware than you currently have.... Flash OI9 BTU and you are OK
lummujaj said:
How many times has been said .... Sboot fail is when you try to flash an older firmware than you currently have.... Flash OI9 BTU and you are OK
Click to expand...
Click to collapse
Okay i will try to flash OI9 BTU
Even though i tried to flash the latest xsg ( my phone is xsg) it failed at the last
Maybe i need flash the pit file too ?
Depending on your model twrp might not work, 3.0.0 and 2.8.7.2 didn't work, I had to use 2.8.7.1, anyways flash that version and UNCHECK AUTO REBOOT ON ODIN and now it should work
Is there anyway i can know which one should i flash
I had 5.1.1 xsg
And my phone is SM-G920F
i took my phone to a phone shop and they can fix it
Even though i dont believe they will be able too
I just wish it works
when i try to flash the latest frimware with odin i get
<ID:0/009> Odin engine v(ID:3.1005)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> SingleDownload.
<ID:0/009> sboot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> cm.bin
<ID:0/009> boot.img
<ID:0/009> recovery.img
<ID:0/009> system.img
<ID:0/009> modem.bin
<ID:0/009> cache.img
<ID:0/009> hidden.img
<ID:0/009> FAIL!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
Click to expand...
Click to collapse
anyone knows what the problem ?
alawii_shark said:
when i try to flash the latest frimware with odin i get
anyone knows what the problem ?
Click to expand...
Click to collapse
Flash only pit file... Do a factory reset (home+volume up+ power) and your ok
model - sm-j700t
version - 6.0.1
kernel version - 3.10.61-9815749
odin - 3.07 and 3.1
twrp - 2.8.7 and 3.0.3
developer options both usb debugging and oem unlock enabled
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
OK i've done this about 5 times. i dont have a problem with w.e version of odin or twrp i use(or so it seems). every attempt is successful. I literally, for the life of me, can not boot into twrp recovery to install supersu. i've watched all the videos and after twrp is flashed the phone booths directly into twrp. my phone reboots normally and i have to turn it off and turn it back on holding volume + up, which ig boots into the regular boot up? it tries to install something, fails, and then goes to the i guess regular boot up. People have even suggested holding volume+up after twrp is flashed but the phone reboots normally anyway. I dont know what im doing wrong I cant get it to boot into twrp. please help
Hold the home button + volume up as soon as you see Removed!!
Sent from my SM-A310F using Tapatalk
Darkfang2u2 said:
model - sm-j700t
version - 6.0.1
kernel version - 3.10.61-9815749
odin - 3.07 and 3.1
twrp - 2.8.7 and 3.0.3
developer options both usb debugging and oem unlock enabled
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
OK i've done this about 5 times. i dont have a problem with w.e version of odin or twrp i use(or so it seems). every attempt is successful. I literally, for the life of me, can not boot into twrp recovery to install supersu. i've watched all the videos and after twrp is flashed the phone booths directly into twrp. my phone reboots normally and i have to turn it off and turn it back on holding volume + up, which ig boots into the regular boot up? it tries to install something, fails, and then goes to the i guess regular boot up. People have even suggested holding volume+up after twrp is flashed but the phone reboots normally anyway. I dont know what im doing wrong I cant get it to boot into twrp. please help
Click to expand...
Click to collapse
Soon as u see pass is how i do it,vol down,home, and power.hold till goes black.then slide vol to up position while u hold the other buttons. Hold till u see twrp booting.DO NOT use vol up first and whatever buttons he said it is NOT correct actually at all.,sorry to the dude who said to do that i mean no disrespect but u are incorrect. Also, make sure u format data, then flash root zip then encryption breaker then reboot if not u will be screwed and not be able to make nandroids. I have posted this on both j7 twrps numerous times. Good luck and sometimes it takes a couple times.
Make sure you have just the right version of TWRP man. I've had this happen the first time. Some versions are for the other J7 models. Get one from the j700t development thread and flash it again. Make sure as soon as you flash TWRP and Odin reboots the device, pull out the battery as soon as you see the Samsung splash screen. This is to prevent stock from overwriting the recovery. Finally, press and hold power up, home and power until it finally boots into TWRP. Message me if this doesn't work
Both versions work on our phone
J700t
Put this file in Odin and it should work for you.
I used it for both of my j700t. download.chainfire.eu/1138/CF-Root/CF-Auto-Root/CF-Auto-Root-j7eltetmo-j7eltetmo-smj700t.zip
You will need to copy and paste this to Google I can't post links.
Also those twrp files don't work on some of these j7 devices for reasons unknown to me.
Darkfang2u2 said:
model - sm-j700t
version - 6.0.1
kernel version - 3.10.61-9815749
odin - 3.07 and 3.1
twrp - 2.8.7 and 3.0.3
developer options both usb debugging and oem unlock enabled
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
OK i've done this about 5 times. i dont have a problem with w.e version of odin or twrp i use(or so it seems). every attempt is successful. I literally, for the life of me, can not boot into twrp recovery to install supersu. i've watched all the videos and after twrp is flashed the phone booths directly into twrp. my phone reboots normally and i have to turn it off and turn it back on holding volume + up, which ig boots into the regular boot up? it tries to install something, fails, and then goes to the i guess regular boot up. People have even suggested holding volume+up after twrp is flashed but the phone reboots normally anyway. I dont know what im doing wrong I cant get it to boot into twrp. please help
Click to expand...
Click to collapse
PM me brother, I'll get you setup.
Depends one the baseband version you have. if its aqc3 or aqf1 twrp is not compatible with those.
---------- Post added at 06:02 PM ---------- Previous post was at 05:38 PM ----------
check the cf auto root website for sm j700t you can root with that now.
Hello guys,
This device was my grandpa's gaming device (Candy Crush) so it has a emotional value.
What do I have:
Hardware:
> GT-N8010 Brazilian version (ZTO)
What is in it:
> Any alpha version of Lineage*
> CWM Recovery v6.0.1.1
* I don't remember what version of Lineage is (but I think it's 14.1 ) because I flashed it a few years ago when rom development for this device was almost dead, and this one I found was an alpha version, but it worked until a beautiful day, when bootloops occured and Unsuccessful Encryption screen showed its face.
The Reset Tablet button on Encryption Screen does nothing.
I'm able to boot on Recovery mode but I can't mount /data, /cache, etc.
I'm able to mount /system but I can't format it due to error.
Code:
Formatting /system...
E: format_volume: make_extf4fs failed on /dev/block/mmcblk0p9
Error formatting /system
I can't mount SDCARD or access it over PC connection.
What have I done so far:
Tried multiple flashes over Odin, using diferent versions of Odin (from 3.04 to the latest build);
More than one PC/USB Ports/Cables;
I also bought a new docker port but I still waiting to be delivered;
What I've tried to flash:
> Brazilian (ZTO) Stock ROM Kies Home type (Single File)
> Recovery Firmwares (Multiple files type BL+AP+CSC file)
> Pit file
> Some TWRP versions as well CWM 6.0.3.0
> Re-partition
All the times I tried I had succeed 1 / failed 0 / PASS! results in Odin, but when I boot the device it's the same.
Some times it bootloops on Lineage bootloader, some others on Unsuccessful Encryption screen.
So no changes at all.
Also, the loading bar appears on the device when Odin is flashing system.img.
Status on Download mode (Even after "successful flash"):
ODIN MODE
PRODUCT NAME:GT-N8010
CUSTOM BINARY DOWNLOAD: no
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
For example:
>> Multiple FIles Flash Odin 3.14 BL+AP+CSC
Code:
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 1789 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> tz.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
>> Single File Flash Odin 3.07 KIES HOME
Code:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> tz.img
<ID:0/003> sboot.bin
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I appreciate any new Ideas, have a nice day you all.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
mandatti said:
Hello guys,
This device was my grandpa's gaming device (Candy Crush) so it has a emotional value.
What do I have:
Hardware:
> GT-N8010 Brazilian version (ZTO)
What is in it:
> Any alpha version of Lineage*
> CWM Recovery v6.0.1.1
* I don't remember what version of Lineage is (but I think it's 14.1 ) because I flashed it a few years ago when rom development for this device was almost dead, and this one I found was an alpha version, but it worked until a beautiful day, when bootloops occured and Unsuccessful Encryption screen showed its face.
The Reset Tablet button on Encryption Screen does nothing.
I'm able to boot on Recovery mode but I can't mount /data, /cache, etc.
I'm able to mount /system but I can't format it due to error.
Code:
Formatting /system...
E: format_volume: make_extf4fs failed on /dev/block/mmcblk0p9
Error formatting /system
I can't mount SDCARD or access it over PC connection.
What have I done so far:
Tried multiple flashes over Odin, using diferent versions of Odin (from 3.04 to the latest build);
More than one PC/USB Ports/Cables;
I also bought a new docker port but I still waiting to be delivered;
What I've tried to flash:
> Brazilian (ZTO) Stock ROM Kies Home type (Single File)
> Recovery Firmwares (Multiple files type BL+AP+CSC file)
> Pit file
> Some TWRP versions as well CWM 6.0.3.0
> Re-partition
All the times I tried I had succeed 1 / failed 0 / PASS! results in Odin, but when I boot the device it's the same.
Some times it bootloops on Lineage bootloader, some others on Unsuccessful Encryption screen.
So no changes at all.
Also, the loading bar appears on the device when Odin is flashing system.img.
Status on Download mode (Even after "successful flash"):
ODIN MODE
PRODUCT NAME:GT-N8010
CUSTOM BINARY DOWNLOAD: no
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
For example:
>> Multiple FIles Flash Odin 3.14 BL+AP+CSC
Code:
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 1789 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> tz.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
>> Single File Flash Odin 3.07 KIES HOME
Code:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> tz.img
<ID:0/003> sboot.bin
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I appreciate any new Ideas, have a nice day you all.
View attachment 5741025
View attachment 5741027
Click to expand...
Click to collapse
I'm really sorry to tell you that your eMMC is locked.
If the devices stay's at the same state after flashing...
In this case the eMMC needs to get replaced, I've done this about 200 times on this tablet, the eMMC itself is not too expensive, IDK if a repair shop does this in your country, we are still doing it.
You also could buy a used mainboard or a used device, but consider that this eMMC is also used and will die someday.
html6405 said:
I'm really sorry to tell you that your eMMC is locked.
If the devices stay's at the same state after flashing...
In this case the eMMC needs to get replaced, I've done this abouht 200 times on this tablet, the eMMC itself is not too expensive, IDK if a repair shop does this in your country, we are still doing it.
You also could buy a used mainboard or a used device, but consider that this eMMC is also used and will die someday.
Click to expand...
Click to collapse
I'm curious why would the eMMC suddenly lock itself?
joseph15two said:
I'm curious why would the eMMC suddenly lock itself?
Click to expand...
Click to collapse
Thats the common EOL behaviour of the klmag2ge4a-a002 eMMC firmware,
you can read it in the data sheet.
It could be that it detected that it were running out of reserve blocks.
html6405 said:
Thats the common EOL behaviour of the klmag2ge4a-a002 eMMC firmware,
you can read it in the data sheet.
It could be that it detected that it were running out of reserve blocks.
Click to expand...
Click to collapse
Oh that's interesting. Thanks for the info!
html6405 said:
I'm really sorry to tell you that your eMMC is locked.
If the devices stay's at the same state after flashing...
In this case the eMMC needs to get replaced, I've done this about 200 times on this tablet, the eMMC itself is not too expensive, IDK if a repair shop does this in your country, we are still doing it.
You also could buy a used mainboard or a used device, but consider that this eMMC is also used and will die someday.
Click to expand...
Click to collapse
got this error with my tablet a long time ago, flashed stock and then lineageos 16 and all is ok
Fixes do vary but dead EMMC been on the forum since month one .
w_tapper said:
got this error with my tablet a long time ago, flashed stock and then lineageos 16 and all is ok
Click to expand...
Click to collapse
I don't believe that you've read the previous post carefully.
He's flashing the stock ROM and still LineageOS boot's up,
this show's for 100% that the eMMC is locked and read only.
In such a case a fake flashing is nearly always possible, but doesn't change anything on the device.
You really have to replace the eMMC like here:
Samsung Galaxy Note 10.1 eMMC replacement | Hier bekommt ein Samsung Galaxy Note 10.1 eine neue eMMC (intern verbauter Speicher), den Vorbereitungsprozess haben wir nicht gefilmt. (eMMC ablöten,... | By Mobile Hard & Software Solutions - Facebook
Hier bekommt ein Samsung Galaxy Note 10.1 eine neue eMMC (intern verbauter Speicher), den Vorbereitungsprozess haben wir nicht gefilmt. (eMMC ablöten,...
fb.watch
html6405 said:
I'm really sorry to tell you that your eMMC is locked.
If the devices stay's at the same state after flashing...
In this case the eMMC needs to get replaced, I've done this about 200 times on this tablet, the eMMC itself is not too expensive, IDK if a repair shop does this in your country, we are still doing it.
You also could buy a used mainboard or a used device, but consider that this eMMC is also used and will die someday.
Click to expand...
Click to collapse
Thank you!
That's what I was suspicious about...
Sad, I'll try to find a eMMC and try to replace it.
I'll post any updates if I have them.
EDIT: Do you have maybe where I can find a eMMC?
A link would be usefull.
I'm based on Germany.
mandatti said:
I'm based on Germany.
Click to expand...
Click to collapse
Thats great, then I could send you a pre-programmed eMMC from Austria, just contact me via PM.
html6405 said:
Thats great, then I could send you a pre-programmed eMMC from Austria, just contact me via PM.
Click to expand...
Click to collapse
Sent. (Y)