Related
I just started developing this odd creaking noise near the bottom and sides of my S4G. Even with a Seidio Active case wrapped around it, the creaking can be felt and heard when hitting the bottom buttons.
The fix is pretty easy. You just need to decrease the amount of movement the back cover has.
I had some .010 mil fiber (fish) paper laying around so I cut a small square that covers the sim card and microsd card area. You can probably use something else, but hey, why not use some insulated paper if you have it.
Lay the paper on top of the area and then slowly place the back cover back on. No holes are in that area above the sim and microsd, so no worries there. You should see an immediate improvement
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
jlevy73 said:
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
Click to expand...
Click to collapse
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
GideonX said:
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
Click to expand...
Click to collapse
I took a post-it and folded it twice. Then placed it on the bottom right area and closed up the cover. For me when I press down on the bottom right side of the screen the whole screen sort of depresses a bit. Only way I could get rid of that was to place the paper in that region. Problem solved.
Post it would have been my backup method
Sent from my HTC Sensation 4G
buy another battery, i recently got an anker also had the creaking problems, noticed the anker is a TINY bit thicker than the stock battery and it removed that problem completely. and that anker battery was DIRT cheap
I just lined the case with some scotch tape. from the bottom to about 3/4 of the way up. I just went around the antenna nubs and the usb hole.
Posted this in another thread, but felt it was valuable here too...
Got the creaking here also, definitely a design flaw. Being obsessive with my devices i couldnt live with it!
I do not recommend putting paper in the cover to fill the gap, as this is just expanding the cover further making it even MORE loose when the paper is not in there. Also i wouldn't recommend it because the paper pushes the back cover out a little more, you may loose a connection for the ground. Which is the little metal springy thing, half way up the right hand side. Obviously its not a good idea to 'push' the cover further away from this ground spot. I have heard that people have had issues with screen responsiveness due to a static build up from not grounding properly.
What i did to fix this problem was a bit of a kitbash of sorts.
Mine was creaking on the bottom right area, like most. The problem is there is too much play between the little black catches on the battery cover and the latch on the handset. Instead of filling up the gap between the phone and the cover (Ala paper, card in the cover) I closed it!
What you need to do is get some very thin plastic film. Like that on kids toy packaging etc. Not the thicker stuff though. This stuff would be under 1mm thick. It came as a viewing window in the box my new wallet came in. So you can sorta imagine what im talking about.
I cut a piece about 10mm long and as wide as one of the two little black catches. I applied a VERY thin coat of super glue to one end of the film. Just enough to cover the area under the catch. Then i carefully placed the film with the superglue on it under the catch, and then quickly applied some pressure to it with some tweezers. Then i carefully cut the excess off with a pair of finely tipped nail scissors.
The result is that it now PULLS the screen/phone INTO the cover more by making the little black catch thicker. Not the opposite (paper method), which pushes the cover out, creating a further problem of adding more paper under the cover over time as the cover expands/loosens to compensate. Not to mention a possible grounding loss and resulting damage.
Hope this helps some people that have had multiple replacements or could not be bothered replacing for such a cosmetic issue. (Like me). It definitely works, just got to get your surgeon on and be accurate with your placement of the film.
Apply this to what ever side creaks the most, and bam its gone. Nice. Solid phone... again.
If anyone wants more specific details etc, im all ears.
Regards,
Matt.
will try it with an double side film ...
i mean a film that hold back cover and phone together ;-) i think doing paper in there will do damage with time
I contacted HTC and they sent me another/new one. No more creaking!
RaptorRVL said:
I contacted HTC and they sent me another/new one. No more creaking!
Click to expand...
Click to collapse
Back cover or whole phone?
I have the same problem too. And it just seems to get more and more "cracking"
Hi guys. I recently saw this (http://blog.whitesites.com/HTC-Sensation-4G-Chrome-Polished-Frame__634471425817343750_blog.htm) and decided to try this on my phone's battery cover. it looks pretty cool now, with the battery door shiny and mirrorish. you can try this out too, but make sure you dont sand the metal too hard after the dark blue paint falls off, because thats going to give it scratches that are hard to remove. you can use about 100 grit to remove the paint, then 400 to make the surface smooth. with the new look, i feel like i have a new phone again. haha
Post pictures when you are done! I was considering it too, but i really like the feel of the blue material...
shungun said:
Post pictures when you are done! I was considering it too, but i really like the feel of the blue material...
Click to expand...
Click to collapse
here, ive uploaded a picture, its in the first post. i like the new texture now, it feels just as smooth as the front glass! and it feels cooler in my hand too (maybe because im touching the metal directly, and not through the paint)
Wow! That looks really good! I'll do this when i have time
So here is a little trick to go along with that. Since the blue / purple backing on the battery cover was a rubber composite, it tended to hold heat more. Now that you got that barrier off, here is the next step. Wrap your battery in aluminum foil and then put the cover on. Since aluminum foil doesn't conduct heat it will transfer it to the backing (since it doesn't actually touch the battery without the foil bridge) and dissipate the heat during use. This will keep your temperature down and for what it is worth, extend lifeline of the battery. I actually did this a long time ago (only in didn't sand the back, I soaked the cover in acetate solution and the rubber peeled right off) and it works fairly well, especially when using CPU for a duration like online music.
Woodrube said:
So here is a little trick to go along with that. Since the blue / purple backing on the battery cover was a rubber composite, it tended to hold heat more. Now that you got that barrier off, here is the next step. Wrap your battery in aluminum foil and then put the cover on. Since aluminum foil doesn't conduct heat it will transfer it to the backing (since it doesn't actually touch the battery without the foil bridge) and dissipate the heat during use. This will keep your temperature down and for what it is worth, extend lifeline of the battery. I actually did this a long time ago (only in didn't sand the back, I soaked the cover in acetate solution and the rubber peeled right off) and it works fairly well, especially when using CPU for a duration like online music.
Click to expand...
Click to collapse
cool, what made you put that cover into the solution? sounds much better cos it doesnt leave scratches. where do you get it?
if you allow heat to go into the cover, wont the phone feel much hotter in your hand? and wouldnt it affect the temperature of the lcd? my phone gets hot sometimes when charging, so i just remove the cover and leave the phone standing on the windowsill to prevent that.
Acetate is really nothing more than nail polish remover. I was getting my Google on a long time ago and came across it. Some kid with an XT did a YouTube video on it.
Since the heat is dissipating out the back, it doesn't effect the LCD on the front. The cover doesn't get too hot and actually the phone runs cooler bc the heat has somewhere to go.
Think of it like a wetsuit. You are totally dry and warm when fully covered, but open the neck a bit and your whole body gets cold. Phone is same way bc of the rubber coating. Remove that and the heat has somewhere to go and not stay trapped inside and cause possible damage to battery and CPU.
Allright. Ever since the last time i've taken out the battery of my Sensation, i've been slightly annoyed.
I've noticed that a small bulge developed in the battery compartment. I've also noticed there are a couple of streaks/scratches.
Why the hell is the battery compartment so susceptible to scratches? Also, should this bulge be of concern? I can even feel it if i run my finger over it.
Is the battery compartment back side actually a black film? You know, where the disposal symbol, and the FCC logo are.
If so, that would explain it, sort of...
not sure if serious. i really wouldn't worry about that, fella.
Oh, i'm serious. It's been bothering me. And i wanna know if the compartment is made of a film of some sort, or if it's plastic.
Prenihility said:
Oh, i'm serious. It's been bothering me. And i wanna know if the compartment is made of a film of some sort, or if it's plastic.
Click to expand...
Click to collapse
I think he meant that the scratches won't be serious.
Sent from my HTC Sensation Z710e using xda premium
Regardless, anyone know what the battery compartment is made of? Not the surrounding area, but the back of where the battery sits. Just as i had described before.
Does ANYONE know?
And can you get a replacement for that part?
It's the same type of metal that is on the exterior of the casing. You can buy a new battery back door housing if you'd like. They go for about $10-20 on ebay or amazon.
MMmmmm... No.
That's not what i'm talking about.
The place where the battery is fitted.
Right there. The spot with the largers amount of surface area in the battery compartment.
There's a disposal symbol on it.
I've got a little bulge there, and some scratches.
It feels soft.
What is it?
Prenihility said:
MMmmmm... No.
That's not what i'm talking about.
The place where the battery is fitted.
Right there. The spot with the largers amount of surface area in the battery compartment.
There's a disposal symbol on it.
I've got a little bulge there, and some scratches.
It feels soft.
What is it?
Click to expand...
Click to collapse
It's made of aluminium, the little silver grounding pin is part of it, it has a square shape, and that aluminium part is connected to the lcd back by other sort of 4 pins. I opened mine to try to clean the dust under my screen, then i realized i needed a heat gun and glue, so i left it like that. The pins that make contact with the lcd may be another possible cause of the touch problem...
Do you want a pic?
Dom42 said:
It's made of aluminium, the little silver grounding pin is part of it, it has a square shape, and that aluminium part is connected to the lcd back by other sort of 4 pins. I opened mine to try to clean the dust under my screen, then i realized i needed a heat gun and glue, so i left it like that. The pins that make contact with the lcd may be another possible cause of the touch problem...
Do you want a pic?
Click to expand...
Click to collapse
No no. Ok. You take the back cover of the phone OFF. And you take the battery OUT. The area behind/around the battery. It's black. It feels softer than any other part of the phone. THAT is what i'm talking about.
I ran my nail along it, and it left a mark... . And i kinda feel bad about it. Although it's inside... and the rest of the phone is in perfect condition.
That's the area on the phone i'm talking about.
Dom42 said:
It's made of aluminium, the little silver grounding pin is part of it, it has a square shape, and that aluminium part is connected to the lcd back by other sort of 4 pins. I opened mine to try to clean the dust under my screen, then i realized i needed a heat gun and glue, so i left it like that. The pins that make contact with the lcd may be another possible cause of the touch problem...
Do you want a pic?
Click to expand...
Click to collapse
I'd like a pic please.
This we overlooked while troubleshooting touchscreen problem.
Thanks
Ahem... eerrrmmm. Is anyone NOT clear of which part of the phone i'm talking about?
Are you talking about the black sticker in the batter compartment? I believe its just a plastic sticker. The bulge is probably either air that got trapped or a bump in the aluminum casing beneath. Either way the bulge and the scratches are purely cosmetic. There is no "replacement" for each sticker has several unique numbers on it. Also why would you even care?
Alright, I did send sms on my bicycle which resulted in I did drop the phone on the ground. Luckily I had ad NILLKIN glass screen protector, which did save most of the phone . I have ordered a new Nillkin screen protector from Aliexpress. And I hope to patch up this phone so it looks good again. How would you have done ?
As you can see at the bottom in the pictures there is physically damage, you can you see the screen bleeding thru also the huwawei logo is damaged.
My idea is UNDER the NEW Nillkin screen protector I will try to mask these "holes" so the screen is not beelding thru anymore. What material should I use to patch up these holes.. also.. how to repar the logo ? can I print it out on my computer printer ? it might look **** on paper but UNDER the glass protector it might look a lot better.
All creative ideas are appreciated, I have high hopes the phone will look good again..
And hopefully my phone will surrive until the M8 release.
Just to let you know desipite the glass look damaged like this the phone is still fully functional!!
ouch i can feel with you.
How about some black film, black paper or everything else that is black and thin
Yes some black material for sure.. Black film would be perfect in guess.. Just wonder where to get it also some black glue at the sides also..
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
alexre123 said:
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
Click to expand...
Click to collapse
Nice man might be a very good alternative! But how easy is it to change it really?
Do I need a heat gun for that?
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Or...if you have the courage go for it ) - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Joke man, don't do it yourself if you don't have experience
alexre123 said:
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Click to expand...
Click to collapse
I have done some smartphone repair myself, I changed the USB board on my old Galaxy Note 1.
I bought a smartphone repair kit with a few tools and very small screwdrivers. To change the glass is probably not much harder, but I need to know if I need a heat gun since I do not own any yet Hopefully it is not needed..but I would assume so...
I might also add the reason I bought a screen protector was that the original glass underneeth have a small crack too that goes accross the entire screen but it s quite invisible besides from certain angels.. so to change that screen to would actually be amazing..and it would make the secondary value when I sell this when M8 is released be a lot higher..
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
alexre123 said:
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
Click to expand...
Click to collapse
Yes the Nillkin glass did its job but I think I was unlucky, that the bottom of the phone got under my bicycle tire.. it felt like it...
I recommend Nillkin, IT has very good Oleophobic coating, which makes the whole device a lot more enjoyable to use, but be careful whren you put it on non 100% straight surfaces it will slip onto the floor.
Alright it is more or less decided I will buy a new front cover with glass, I will make sure to get original parts with gorilla glass. Since the ebay link you linked to are chipped from china I guess I can just order straight from alixpress instead...
I have heard singapore post have quite fast shipping compared to china post.
just one question is hard to see in the videos.. but do I really need to disassembly every component all the circuits boards just to change the front screen ? do I need to open the case at all when using the heat gun/hair dryer ?
If as in the every component and circuit board has to be disassembled it is over my competence probably... unless I am super careful..
Mutch better if you want to purchase an original front to replace it. Don,t know if you really need to take all the components of for replacing the front screen, but you can make some research on it or you can ask on other forums, maybe are others with more experience.
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
blackinfinity said:
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
Click to expand...
Click to collapse
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
ehhm... good luck OP
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
blackinfinity said:
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
Click to expand...
Click to collapse
Sorry but you are like 10 year old child..
So u wanna change your ''front Screen Outer Glass Lens'' ??? (that is damn long name for glass )
You have so much hopes ? OK .. go on .. I leave you to it ..
I wish you very best of luck ..
''''IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT''
DDDDDD this was so funny :laugh: :good:
Fingers :fingers-crossed:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
blackinfinity said:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
Click to expand...
Click to collapse
And I will give you one last advice ; that my detailed post above I explained you how difficult it is .. YOU want to change glass only ??
And what you think, you can just do it without stripping phone apart ?? Are you magician ? You would have to open phone anyway !
And replacing glass on your screen, do you have any idea how you gonna do it? Removing glass from LCD is x10 TIMES hard that my instructions above man !
So you basically adding even more, harder work to hard work ..!
Do you even have
1.LCD separator heat machine ??
2.Cutting line wire ??
3.Cleaning alcohol chemicals ??
4.Optical clear adhesive glue ??
5.Ultraviolet curing lamp ??
Come oon man ...
I told you I wish you very best of luck..
This guy want to do the exact same thing - https://www.youtube.com/watch?v=O8HNBtl9MwI
You have the all process here - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Take a look and decide if you want do it yourself and risk to mess things up or go with the phone and the replacing part to a service and let someone who did this before.
My display damaged and i wanna to ask you smth guys.
How difficulty is it to change it by myself?
I watch this video "
" and i concluded its pretty easy to change it. But the only tool i dont have is the heatgun the other tools i can buy.
Tell me your opinion. Is it easy to do?
Can't tell if it's easy, but in other situations that I needed a heat gun and didn't have one, I used a hair dryer, which is way more common to have at home, or at least easier to borrow from a neighbor or something like that
Watch tear down and repair vids.
If a repair shop will let you watch them do it.
ESD, learn and understand what it is. Discreet components ie the display and mobo are very susceptible to it out of circuit.
Bare minimum protection is a bare wood surface to work on and a relative room humidity of 50% or better. A earth grounded ESD mat and wrist strap is best
Disconnect the battery as soon as possible in the disassembly process. Discharge below 40% if possible before starting.
Have all the drivers, picks, fine precision tweezers, and tools needed. Excellent light and a 2X or so optical visor be nice.
Inspect for additional damage*.
Have a set of OEM seals and now's a good time to replace the battery if it's performance has noticably dropped.
Take pictures disassembling if needed. It must be put back together exactly as it was.
Do Not over torgue screws... less is better.
Be very careful not to damage the ribbon microconnectors.
Take your time, no rush.
*any impact that can break the display or bend the frame can damage the mobo. High G loads or direct impacts can damage chipsets internally, fracture solder joints and internally damaged multilayered mobo PCB internal traces.
I did it three days ago, bc my mix 3 had contact with water.
Its kind of easy to do with a hairdryer and a small plastic tool.
The hardest part is to glue it back together.
(But I have to say my screen didn't work afterwards. The expert in the phone repair store said its maybe a problem on the motherboard)
slowmotion11 said:
I did it three days ago, bc my mix 3 had contact with water.
Its kind of easy to do with a hairdryer and a small plastic tool.
The hardest part is to glue it back together.
(But I have to say my screen didn't work afterwards. The expert in the phone repair store said its maybe a problem on the motherboard)
Click to expand...
Click to collapse
If the battery isn't promptly removed and especially if it's not immediately powered down the current can cause corrosion and short out circuits. The power section is particularly vulnerable. Try again, inspect mobo and the ribbon connectors for signs of corrosion and moisture. Use bright light and magnification.
Is it completely dry? A good soaking with anhydrous isopropyl will help remove hidden water. Again dry completely afterwards. Getting the underside of BGA chipsets dry is imperative.
The micro connectors tend to trap moisture too.
Careful use of compressed air can be very useful but the key word here is careful. Don't stick a nozzle with 100 psi an inch or two from the mobo! Either use low pressure clean, dry air or back it up for high pressure air.
Use your best judgment... it's a bit of an art.
After you dry it as good as possible let it sit in a warm, dry room with a fan on it. Complete drying may take days without disassembly.
Thank you for the tips! I will try it like you described
The same is true with flooded cars, promptly pulling the battery can limit the damage even save the vehicle.
Be wary on flood damage vehicles for sale now, always check for water lines/marks
Most will suffer impossible electrical problems forever. Brine water always kills...